Skip to contentSkip to conversation

imx: imx8mm_beacon: Eliminate a few extras to free up SPL space

PATCH In review Adam Ford 5 participants 16 messages Oct 22, 2022 – Nov 8, 2022

Subsystems (2)
lore
Share & tools
lore

Adam Ford

author
#0 lore raw

PATCH 1/3 imx: imx8mm_beacon: Eliminate a few extras to free up SPL space

There are a few functions which are not essential for use in SPL, but they take up enough space to make other preferred features not fit. Remove the extras.

board/beacon/imx8mm/spl.c +0 -5
index a93cc93878..b0e9d918da 100644
@@ -44,11 +44,6 @@ static void spl_dram_init(void)
 	ddr_init(&dram_timing);
 }
 
-void spl_board_init(void)
-{
-	debug("Normal Boot\n");
-}
-
 #ifdef CONFIG_SPL_LOAD_FIT
 int board_fit_config_name_match(const char *name)
 {
configs/imx8mm_beacon_defconfig +1 -7
index e37ce01c19..f6a1012d8a 100644
@@ -29,7 +29,6 @@ CONFIG_DEFAULT_FDT_FILE="imx8mm-beacon-kit.dtb"
 CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
 CONFIG_SPL_BSS_START_ADDR=0x910000
 CONFIG_SPL_BSS_MAX_SIZE=0x2000
-CONFIG_SPL_BOARD_INIT=y
 # CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
 CONFIG_SPL_STACK=0x920000
 CONFIG_SYS_SPL_MALLOC=y
@@ -88,12 +87,9 @@ CONFIG_DM_PCA953X=y
 CONFIG_DM_I2C=y
 CONFIG_SUPPORT_EMMC_BOOT=y
 CONFIG_MMC_IO_VOLTAGE=y
-CONFIG_SPL_MMC_IO_VOLTAGE=y
 CONFIG_MMC_UHS_SUPPORT=y
-CONFIG_SPL_MMC_UHS_SUPPORT=y
 CONFIG_MMC_HS400_ES_SUPPORT=y
 CONFIG_MMC_HS400_SUPPORT=y
-CONFIG_SPL_MMC_HS400_SUPPORT=y
 CONFIG_FSL_USDHC=y
 CONFIG_MTD=y
 CONFIG_DM_MTD=y
@@ -113,14 +109,12 @@ CONFIG_PINCTRL_IMX8M=y
 CONFIG_POWER_DOMAIN=y
 CONFIG_IMX8M_POWER_DOMAIN=y
 CONFIG_DM_PMIC=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
 CONFIG_DM_PMIC_BD71837=y
 CONFIG_SPL_DM_PMIC_BD71837=y
 CONFIG_DM_REGULATOR=y
-CONFIG_SPL_DM_REGULATOR=y
 CONFIG_DM_REGULATOR_BD71837=y
-CONFIG_SPL_DM_REGULATOR_BD71837=y
 CONFIG_DM_REGULATOR_FIXED=y
-CONFIG_SPL_DM_REGULATOR_FIXED=y
 CONFIG_DM_REGULATOR_GPIO=y
 CONFIG_DM_SERIAL=y
 CONFIG_MXC_UART=y
Signature · 1 line
2.34.1
author
#1 lore raw

PATCH 2/3 imx: imx8mm-beacon: Enable USB booting via SDP

In order to boot over USB, the device tree needs to enable a few extra nodes in SPL. Since the USB driver has the ability to detect host/device, the dr_mode can be removed from the device tree since it needs to act as a device when booting and OTG is the default mode. Add USB boot support to spl_board_boot_device and enable the corresponding config options.

arch/arm/dts/imx8mm-beacon-kit-u-boot.dtsi +17 -1
index c94b4ffa4c..00ac413f36 100644
@@ -13,6 +13,10 @@
 	};
 };
 
+&aips4 {
+	u-boot,dm-spl;
+};
+
 &reg_usdhc2_vmmc {
 	u-boot,off-on-delay-us = <20000>;
 };
@@ -77,12 +81,24 @@
 	u-boot,dm-spl;
 };
 
+&reg_usbotg1 {
+
+};
+
 &uart2 {
 	u-boot,dm-spl;
 };
 
+&usbmisc1 {
+	u-boot,dm-spl;
+};
+
 &usbotg1 {
-	dr_mode="host";
+	u-boot,dm-spl;
+};
+
+&usbphynop1 {
+	u-boot,dm-spl;
 };
 
 &usdhc2 {
board/beacon/imx8mm/spl.c +2 -0
index b0e9d918da..a5f337aa17 100644
@@ -34,6 +34,8 @@ int spl_board_boot_device(enum boot_device boot_dev_spl)
 	case SD3_BOOT:
 	case MMC3_BOOT:
 		return BOOT_DEVICE_MMC2;
+	case USB_BOOT:
+		return BOOT_DEVICE_BOARD;
 	default:
 		return BOOT_DEVICE_NONE;
 	}
configs/imx8mm_beacon_defconfig +8 -1
index f6a1012d8a..90a623515e 100644
@@ -39,6 +39,9 @@ CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300
 CONFIG_SPL_I2C=y
 CONFIG_SPL_POWER=y
+CONFIG_SPL_USB_HOST=y
+CONFIG_SPL_USB_GADGET=y
+CONFIG_SPL_USB_SDP_SUPPORT=y
 CONFIG_SPL_WATCHDOG=y
 CONFIG_HUSH_PARSER=y
 CONFIG_SYS_MAXARGS=64
@@ -56,6 +59,7 @@ CONFIG_CMD_MMC=y
 CONFIG_CMD_PART=y
 CONFIG_CMD_SPI=y
 CONFIG_CMD_USB=y
+CONFIG_CMD_USB_SDP=y
 CONFIG_CMD_USB_MASS_STORAGE=y
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
@@ -103,6 +107,8 @@ CONFIG_PHY_ATHEROS=y
 CONFIG_PHY_GIGE=y
 CONFIG_FEC_MXC=y
 CONFIG_MII=y
+CONFIG_SPL_PHY=y
+CONFIG_SPL_NOP_PHY=y
 CONFIG_PINCTRL=y
 CONFIG_SPL_PINCTRL=y
 CONFIG_PINCTRL_IMX8M=y
@@ -127,12 +133,13 @@ CONFIG_SYSRESET_PSCI=y
 CONFIG_SYSRESET_WATCHDOG=y
 CONFIG_DM_THERMAL=y
 CONFIG_USB=y
-# CONFIG_SPL_DM_USB is not set
 CONFIG_USB_EHCI_HCD=y
+CONFIG_MXC_USB_OTG_HACTIVE=y
 CONFIG_USB_STORAGE=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_GADGET_VENDOR_NUM=0x0525
 CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
 CONFIG_CI_UDC=y
+CONFIG_SDP_LOADADDR=0x40400000
 CONFIG_USB_GADGET_DOWNLOAD=y
 CONFIG_IMX_WATCHDOG=y
Signature · 1 line
2.34.1
reviewer Reviewed-by on v1 2/3
#2 lore raw

Re: [PATCH 2/3] imx: imx8mm-beacon: Enable USB booting via SDP

Quoted 10 lines · Adam Ford

In order to boot over USB, the device tree needs to enable a few extra nodes in SPL. Since the USB driver has the ability to detect host/device, the dr_mode can be removed from the device tree since it needs to act as a device when booting and OTG is the default mode. Add USB boot support to spl_board_boot_device and enable the corresponding config options.

#3 lore raw

PATCH 2/3 imx: imx8mm-beacon: Enable USB booting via SDP

In reply to Adam Ford
Quoted 99 lines

In order to boot over USB, the device tree needs to enable a few extra nodes in SPL. Since the USB driver has the ability to detect host/device, the dr_mode can be removed from the device tree since it needs to act as a device when booting and OTG is the default mode. Add USB boot support to spl_board_boot_device and enable the corresponding config options.

arch/arm/dts/imx8mm-beacon-kit-u-boot.dtsi +17 -1
index c94b4ffa4c..00ac413f36 100644
@@ -13,6 +13,10 @@
 	};
 };
 
+&aips4 {
+	u-boot,dm-spl;
+};
+
 &reg_usdhc2_vmmc {
 	u-boot,off-on-delay-us = <20000>;
 };
@@ -77,12 +81,24 @@
 	u-boot,dm-spl;
 };
 
+&reg_usbotg1 {
+
+};
+
 &uart2 {
 	u-boot,dm-spl;
 };
 
+&usbmisc1 {
+	u-boot,dm-spl;
+};
+
 &usbotg1 {
-	dr_mode="host";
+	u-boot,dm-spl;
+};
+
+&usbphynop1 {
+	u-boot,dm-spl;
 };
 
 &usdhc2 {
board/beacon/imx8mm/spl.c +2 -0
index b0e9d918da..a5f337aa17 100644
@@ -34,6 +34,8 @@ int spl_board_boot_device(enum boot_device boot_dev_spl)
 	case SD3_BOOT:
 	case MMC3_BOOT:
 		return BOOT_DEVICE_MMC2;
+	case USB_BOOT:
+		return BOOT_DEVICE_BOARD;
 	default:
 		return BOOT_DEVICE_NONE;
 	}
configs/imx8mm_beacon_defconfig +6 -1
index f6a1012d8a..90a623515e 100644
@@ -39,6 +39,9 @@ CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300
 CONFIG_SPL_I2C=y
 CONFIG_SPL_POWER=y
+CONFIG_SPL_USB_HOST=y
+CONFIG_SPL_USB_GADGET=y
+CONFIG_SPL_USB_SDP_SUPPORT=y
 CONFIG_SPL_WATCHDOG=y
 CONFIG_HUSH_PARSER=y
 CONFIG_SYS_MAXARGS=64
@@ -56,6 +59,7 @@ CONFIG_CMD_MMC=y
 CONFIG_CMD_PART=y
 CONFIG_CMD_SPI=y
 CONFIG_CMD_USB=y
+CONFIG_CMD_USB_SDP=y
 CONFIG_CMD_USB_MASS_STORAGE=y
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
@@ -103,6 +107,8 @@ CONFIG_PHY_ATHEROS=y
 CONFIG_PHY_GIGE=y
 CONFIG_FEC_MXC=y
 CONFIG_MII=y
+CONFIG_SPL_PHY=y
+CONFIG_SPL_NOP_PHY=y
 CONFIG_PINCTRL=y
 CONFIG_SPL_PINCTRL=y
 CONFIG_PINCTRL_IMX8M=y
@@ -127,12 +133,13 @@ CONFIG_SYSRESET_PSCI=y
 CONFIG_SYSRESET_WATCHDOG=y
 CONFIG_DM_THERMAL=y
 CONFIG_USB=y
-# CONFIG_SPL_DM_USB is not set

configs/imx8mm_beacon_defconfig CONFIG_SYSRESET_PSCI=y · line 145

Quoted 10 lines
configs/imx8mm_beacon_defconfig +2 -0
 CONFIG_USB_EHCI_HCD=y
+CONFIG_MXC_USB_OTG_HACTIVE=y
 CONFIG_USB_STORAGE=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_GADGET_VENDOR_NUM=0x0525
 CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
 CONFIG_CI_UDC=y
+CONFIG_SDP_LOADADDR=0x40400000
 CONFIG_USB_GADGET_DOWNLOAD=y
 CONFIG_IMX_WATCHDOG=y

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
author
#4 lore raw

PATCH 3/3 imx: imx8mm-beacon: Move Environment to eMMC partition 2

In reply to Adam Ford

The downstream U-Boot distributed by Beacon stores the environment in the eMMC and the end of partition 2. This allow the environment to stay on the SOM regardless of the boot source.

configs/imx8mm_beacon_defconfig +4 -3
index 90a623515e..4dd87914b8 100644
@@ -5,8 +5,8 @@ CONFIG_SYS_MALLOC_LEN=0x2000000
 CONFIG_SPL_GPIO=y
 CONFIG_SPL_LIBCOMMON_SUPPORT=y
 CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_ENV_SIZE=0x1000
-CONFIG_ENV_OFFSET=0x400000
+CONFIG_ENV_SIZE=0x2000
+CONFIG_ENV_OFFSET=0xFFFFDE00
 CONFIG_DM_GPIO=y
 CONFIG_DEFAULT_DEVICE_TREE="imx8mm-beacon-kit"
 CONFIG_SPL_TEXT_BASE=0x7E1000
@@ -76,7 +76,8 @@ CONFIG_SPL_OF_CONTROL=y
 CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_SYS_MMC_ENV_DEV=1
+CONFIG_SYS_MMC_ENV_DEV=2
+CONFIG_SYS_MMC_ENV_PART=2
 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
 CONFIG_USE_ETHPRIME=y
 CONFIG_ETHPRIME="FEC"
Signature · 1 line
2.34.1
reviewer Reviewed-by on v1 3/3
#5 lore raw

Re: [PATCH 3/3] imx: imx8mm-beacon: Move Environment to eMMC partition 2

Quoted 6 lines · Adam Ford

The downstream U-Boot distributed by Beacon stores the environment in the eMMC and the end of partition 2. This allow the environment to stay on the SOM regardless of the boot source.

#6 lore raw

PATCH 3/3 imx: imx8mm-beacon: Move Environment to eMMC partition 2

In reply to Adam Ford
Quoted 21 lines

The downstream U-Boot distributed by Beacon stores the environment in the eMMC and the end of partition 2. This allow the environment to stay on the SOM regardless of the boot source.

configs/imx8mm_beacon_defconfig +2 -2
index 90a623515e..4dd87914b8 100644
@@ -5,8 +5,8 @@ CONFIG_SYS_MALLOC_LEN=0x2000000
 CONFIG_SPL_GPIO=y
 CONFIG_SPL_LIBCOMMON_SUPPORT=y
 CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_ENV_SIZE=0x1000
-CONFIG_ENV_OFFSET=0x400000
+CONFIG_ENV_SIZE=0x2000
+CONFIG_ENV_OFFSET=0xFFFFDE00
 CONFIG_DM_GPIO=y
 CONFIG_DEFAULT_DEVICE_TREE="imx8mm-beacon-kit"
 CONFIG_SPL_TEXT_BASE=0x7E1000

configs/imx8mm_beacon_defconfig CONFIG_SPL_OF_CONTROL=y · line 83

Quoted 9 lines
configs/imx8mm_beacon_defconfig +2 -1
@@ -76,7 +76,8 @@ CONFIG_SPL_OF_CONTROL=y
 CONFIG_ENV_OVERWRITE=y
 CONFIG_ENV_IS_IN_MMC=y
 CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_SYS_MMC_ENV_DEV=1
+CONFIG_SYS_MMC_ENV_DEV=2
+CONFIG_SYS_MMC_ENV_PART=2
 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
 CONFIG_USE_ETHPRIME=y
 CONFIG_ETHPRIME="FEC"

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
#8 lore raw
In reply to Adam Ford
Quoted 65 lines · Adam Ford

There are a few functions which are not essential for use in SPL, but they take up enough space to make other preferred features not fit. Remove the extras.

board/beacon/imx8mm/spl.c +0 -5
index a93cc93878..b0e9d918da 100644
@@ -44,11 +44,6 @@ static void spl_dram_init(void)
        ddr_init(&dram_timing);
 }
 
-void spl_board_init(void)
-{
-       debug("Normal Boot\n");
-}
-
 #ifdef CONFIG_SPL_LOAD_FIT
 int board_fit_config_name_match(const char *name)
 {
configs/imx8mm_beacon_defconfig +1 -8
index e37ce01c19..f6a1012d8a 100644
@@ -29,7 +29,6 @@ CONFIG_DEFAULT_FDT_FILE="imx8mm-beacon-kit.dtb"
 CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
 CONFIG_SPL_BSS_START_ADDR=0x910000
 CONFIG_SPL_BSS_MAX_SIZE=0x2000
-CONFIG_SPL_BOARD_INIT=y
 # CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
 CONFIG_SPL_STACK=0x920000
 CONFIG_SYS_SPL_MALLOC=y
@@ -88,12 +87,9 @@ CONFIG_DM_PCA953X=y
 CONFIG_DM_I2C=y
 CONFIG_SUPPORT_EMMC_BOOT=y
 CONFIG_MMC_IO_VOLTAGE=y
-CONFIG_SPL_MMC_IO_VOLTAGE=y
 CONFIG_MMC_UHS_SUPPORT=y
-CONFIG_SPL_MMC_UHS_SUPPORT=y
 CONFIG_MMC_HS400_ES_SUPPORT=y
 CONFIG_MMC_HS400_SUPPORT=y
-CONFIG_SPL_MMC_HS400_SUPPORT=y
 CONFIG_FSL_USDHC=y
 CONFIG_MTD=y
 CONFIG_DM_MTD=y
@@ -113,14 +109,12 @@ CONFIG_PINCTRL_IMX8M=y
 CONFIG_POWER_DOMAIN=y
 CONFIG_IMX8M_POWER_DOMAIN=y
 CONFIG_DM_PMIC=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
 CONFIG_DM_PMIC_BD71837=y
 CONFIG_SPL_DM_PMIC_BD71837=y
 CONFIG_DM_REGULATOR=y
-CONFIG_SPL_DM_REGULATOR=y
 CONFIG_DM_REGULATOR_BD71837=y
-CONFIG_SPL_DM_REGULATOR_BD71837=y
 CONFIG_DM_REGULATOR_FIXED=y
-CONFIG_SPL_DM_REGULATOR_FIXED=y
 CONFIG_DM_REGULATOR_GPIO=y
 CONFIG_DM_SERIAL=y
 CONFIG_MXC_UART=y
--
Quoted 2 lines

2.34.1

Adam,

I'm looking at your patches as I'm also trying to strip down the imx8mm-venice SPL so that I can fit DM USB support. It seems that all/most of the imx8m boards have a spl_board_init() which calls arch_misc_init(). I'm curious why your not calling that function?

Another config that I've found to save a lot of space for imx8m without any negative impact I can see is CONFIG_SPL_MMC_TINY=y

Best Regards,

Tim

author
#9 lore raw
Quoted 72 lines · Tim Harvey
Quoted 65 lines · Adam Ford

There are a few functions which are not essential for use in SPL, but they take up enough space to make other preferred features not fit. Remove the extras.

board/beacon/imx8mm/spl.c +0 -5
index a93cc93878..b0e9d918da 100644
@@ -44,11 +44,6 @@ static void spl_dram_init(void)
        ddr_init(&dram_timing);
 }
 
-void spl_board_init(void)
-{
-       debug("Normal Boot\n");
-}
-
 #ifdef CONFIG_SPL_LOAD_FIT
 int board_fit_config_name_match(const char *name)
 {
configs/imx8mm_beacon_defconfig +1 -8
index e37ce01c19..f6a1012d8a 100644
@@ -29,7 +29,6 @@ CONFIG_DEFAULT_FDT_FILE="imx8mm-beacon-kit.dtb"
 CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
 CONFIG_SPL_BSS_START_ADDR=0x910000
 CONFIG_SPL_BSS_MAX_SIZE=0x2000
-CONFIG_SPL_BOARD_INIT=y
 # CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
 CONFIG_SPL_STACK=0x920000
 CONFIG_SYS_SPL_MALLOC=y
@@ -88,12 +87,9 @@ CONFIG_DM_PCA953X=y
 CONFIG_DM_I2C=y
 CONFIG_SUPPORT_EMMC_BOOT=y
 CONFIG_MMC_IO_VOLTAGE=y
-CONFIG_SPL_MMC_IO_VOLTAGE=y
 CONFIG_MMC_UHS_SUPPORT=y
-CONFIG_SPL_MMC_UHS_SUPPORT=y
 CONFIG_MMC_HS400_ES_SUPPORT=y
 CONFIG_MMC_HS400_SUPPORT=y
-CONFIG_SPL_MMC_HS400_SUPPORT=y
 CONFIG_FSL_USDHC=y
 CONFIG_MTD=y
 CONFIG_DM_MTD=y
@@ -113,14 +109,12 @@ CONFIG_PINCTRL_IMX8M=y
 CONFIG_POWER_DOMAIN=y
 CONFIG_IMX8M_POWER_DOMAIN=y
 CONFIG_DM_PMIC=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
 CONFIG_DM_PMIC_BD71837=y
 CONFIG_SPL_DM_PMIC_BD71837=y
 CONFIG_DM_REGULATOR=y
-CONFIG_SPL_DM_REGULATOR=y
 CONFIG_DM_REGULATOR_BD71837=y
-CONFIG_SPL_DM_REGULATOR_BD71837=y
 CONFIG_DM_REGULATOR_FIXED=y
-CONFIG_SPL_DM_REGULATOR_FIXED=y
 CONFIG_DM_REGULATOR_GPIO=y
 CONFIG_DM_SERIAL=y
 CONFIG_MXC_UART=y
--
Quoted 2 lines

2.34.1

Adam,

Quoted 4 lines

I'm looking at your patches as I'm also trying to strip down the imx8mm-venice SPL so that I can fit DM USB support. It seems that all/most of the imx8m boards have a spl_board_init() which calls arch_misc_init(). I'm curious why your not calling that function?

As of right now, we're not using the CAAM which is initialized in arch_misc_init. If/When we do, we'll likely have to pull that in.

Quoted 3 lines

Another config that I've found to save a lot of space for imx8m without any negative impact I can see is CONFIG_SPL_MMC_TINY=y

I experimented a bit with that too, but I hadn't fully tested switching between booting between MMC1 and MMC2, so I wasn't quite ready to enable it, but I'll spend some more time with it to see how much more space I can shave off SPL.
Getting rid of the PMIC children in SPL helped me quite a bit.

thanks!

adam

Quoted 4 lines

Best Regards,

Tim

#10 lore raw
Quoted 74 lines · Adam Ford
Quoted 72 lines · Tim Harvey
Quoted 65 lines · Adam Ford

There are a few functions which are not essential for use in SPL, but they take up enough space to make other preferred features not fit. Remove the extras.

board/beacon/imx8mm/spl.c +0 -5
index a93cc93878..b0e9d918da 100644
@@ -44,11 +44,6 @@ static void spl_dram_init(void)
        ddr_init(&dram_timing);
 }
 
-void spl_board_init(void)
-{
-       debug("Normal Boot\n");
-}
-
 #ifdef CONFIG_SPL_LOAD_FIT
 int board_fit_config_name_match(const char *name)
 {
configs/imx8mm_beacon_defconfig +1 -8
index e37ce01c19..f6a1012d8a 100644
@@ -29,7 +29,6 @@ CONFIG_DEFAULT_FDT_FILE="imx8mm-beacon-kit.dtb"
 CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
 CONFIG_SPL_BSS_START_ADDR=0x910000
 CONFIG_SPL_BSS_MAX_SIZE=0x2000
-CONFIG_SPL_BOARD_INIT=y
 # CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
 CONFIG_SPL_STACK=0x920000
 CONFIG_SYS_SPL_MALLOC=y
@@ -88,12 +87,9 @@ CONFIG_DM_PCA953X=y
 CONFIG_DM_I2C=y
 CONFIG_SUPPORT_EMMC_BOOT=y
 CONFIG_MMC_IO_VOLTAGE=y
-CONFIG_SPL_MMC_IO_VOLTAGE=y
 CONFIG_MMC_UHS_SUPPORT=y
-CONFIG_SPL_MMC_UHS_SUPPORT=y
 CONFIG_MMC_HS400_ES_SUPPORT=y
 CONFIG_MMC_HS400_SUPPORT=y
-CONFIG_SPL_MMC_HS400_SUPPORT=y
 CONFIG_FSL_USDHC=y
 CONFIG_MTD=y
 CONFIG_DM_MTD=y
@@ -113,14 +109,12 @@ CONFIG_PINCTRL_IMX8M=y
 CONFIG_POWER_DOMAIN=y
 CONFIG_IMX8M_POWER_DOMAIN=y
 CONFIG_DM_PMIC=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
 CONFIG_DM_PMIC_BD71837=y
 CONFIG_SPL_DM_PMIC_BD71837=y
 CONFIG_DM_REGULATOR=y
-CONFIG_SPL_DM_REGULATOR=y
 CONFIG_DM_REGULATOR_BD71837=y
-CONFIG_SPL_DM_REGULATOR_BD71837=y
 CONFIG_DM_REGULATOR_FIXED=y
-CONFIG_SPL_DM_REGULATOR_FIXED=y
 CONFIG_DM_REGULATOR_GPIO=y
 CONFIG_DM_SERIAL=y
 CONFIG_MXC_UART=y
--
Quoted 2 lines

2.34.1

Adam,

Quoted 8 lines
Quoted 4 lines

I'm looking at your patches as I'm also trying to strip down the imx8mm-venice SPL so that I can fit DM USB support. It seems that all/most of the imx8m boards have a spl_board_init() which calls arch_misc_init(). I'm curious why your not calling that function?

As of right now, we're not using the CAAM which is initialized in arch_misc_init. If/When we do, we'll likely have to pull that in.

ok - makes sense.

Quoted 9 lines
Quoted 3 lines

Another config that I've found to save a lot of space for imx8m without any negative impact I can see is CONFIG_SPL_MMC_TINY=y

I experimented a bit with that too, but I hadn't fully tested switching between booting between MMC1 and MMC2, so I wasn't quite ready to enable it, but I'll spend some more time with it to see how much more space I can shave off SPL.
Getting rid of the PMIC children in SPL helped me quite a bit.

I see. It appears to save about 2K and Fabio's imx8mm clk reduction series that made it in saves another 800 bytes or so.

Regardless I'm still oversize for imx8mm-venice by 2K bytes and looking for things to prune. My issue is that I have 4 DRAM configs to support which suck up 3K each I believe.

Tim

author
#11 lore raw
Quoted 97 lines · Tim Harvey
Quoted 74 lines · Adam Ford
Quoted 72 lines · Tim Harvey
Quoted 65 lines · Adam Ford

There are a few functions which are not essential for use in SPL, but they take up enough space to make other preferred features not fit. Remove the extras.

board/beacon/imx8mm/spl.c +0 -5
index a93cc93878..b0e9d918da 100644
@@ -44,11 +44,6 @@ static void spl_dram_init(void)
        ddr_init(&dram_timing);
 }
 
-void spl_board_init(void)
-{
-       debug("Normal Boot\n");
-}
-
 #ifdef CONFIG_SPL_LOAD_FIT
 int board_fit_config_name_match(const char *name)
 {
configs/imx8mm_beacon_defconfig +1 -8
index e37ce01c19..f6a1012d8a 100644
@@ -29,7 +29,6 @@ CONFIG_DEFAULT_FDT_FILE="imx8mm-beacon-kit.dtb"
 CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
 CONFIG_SPL_BSS_START_ADDR=0x910000
 CONFIG_SPL_BSS_MAX_SIZE=0x2000
-CONFIG_SPL_BOARD_INIT=y
 # CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
 CONFIG_SPL_STACK=0x920000
 CONFIG_SYS_SPL_MALLOC=y
@@ -88,12 +87,9 @@ CONFIG_DM_PCA953X=y
 CONFIG_DM_I2C=y
 CONFIG_SUPPORT_EMMC_BOOT=y
 CONFIG_MMC_IO_VOLTAGE=y
-CONFIG_SPL_MMC_IO_VOLTAGE=y
 CONFIG_MMC_UHS_SUPPORT=y
-CONFIG_SPL_MMC_UHS_SUPPORT=y
 CONFIG_MMC_HS400_ES_SUPPORT=y
 CONFIG_MMC_HS400_SUPPORT=y
-CONFIG_SPL_MMC_HS400_SUPPORT=y
 CONFIG_FSL_USDHC=y
 CONFIG_MTD=y
 CONFIG_DM_MTD=y
@@ -113,14 +109,12 @@ CONFIG_PINCTRL_IMX8M=y
 CONFIG_POWER_DOMAIN=y
 CONFIG_IMX8M_POWER_DOMAIN=y
 CONFIG_DM_PMIC=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
 CONFIG_DM_PMIC_BD71837=y
 CONFIG_SPL_DM_PMIC_BD71837=y
 CONFIG_DM_REGULATOR=y
-CONFIG_SPL_DM_REGULATOR=y
 CONFIG_DM_REGULATOR_BD71837=y
-CONFIG_SPL_DM_REGULATOR_BD71837=y
 CONFIG_DM_REGULATOR_FIXED=y
-CONFIG_SPL_DM_REGULATOR_FIXED=y
 CONFIG_DM_REGULATOR_GPIO=y
 CONFIG_DM_SERIAL=y
 CONFIG_MXC_UART=y
--
Quoted 2 lines

2.34.1

Adam,

Quoted 8 lines
Quoted 4 lines

I'm looking at your patches as I'm also trying to strip down the imx8mm-venice SPL so that I can fit DM USB support. It seems that all/most of the imx8m boards have a spl_board_init() which calls arch_misc_init(). I'm curious why your not calling that function?

As of right now, we're not using the CAAM which is initialized in arch_misc_init. If/When we do, we'll likely have to pull that in.

ok - makes sense.

Quoted 9 lines
Quoted 3 lines

Another config that I've found to save a lot of space for imx8m without any negative impact I can see is CONFIG_SPL_MMC_TINY=y

I experimented a bit with that too, but I hadn't fully tested switching between booting between MMC1 and MMC2, so I wasn't quite ready to enable it, but I'll spend some more time with it to see how much more space I can shave off SPL.
Getting rid of the PMIC children in SPL helped me quite a bit.

Quoted 6 lines

I see. It appears to save about 2K and Fabio's imx8mm clk reduction series that made it in saves another 800 bytes or so.

Regardless I'm still oversize for imx8mm-venice by 2K bytes and looking for things to prune. My issue is that I have 4 DRAM configs to support which suck up 3K each I believe.

Can you split the DRAM configs into different _defconfig files so only the DRAM config you want is built-in?

adam

Quoted 2 lines

Tim

#12 lore raw
Quoted 102 lines · Adam Ford
Quoted 100 lines · Tim Harvey
Quoted 74 lines · Adam Ford
Quoted 72 lines · Tim Harvey
Quoted 65 lines · Adam Ford

There are a few functions which are not essential for use in SPL, but they take up enough space to make other preferred features not fit. Remove the extras.

board/beacon/imx8mm/spl.c +0 -5
index a93cc93878..b0e9d918da 100644
@@ -44,11 +44,6 @@ static void spl_dram_init(void)
        ddr_init(&dram_timing);
 }
 
-void spl_board_init(void)
-{
-       debug("Normal Boot\n");
-}
-
 #ifdef CONFIG_SPL_LOAD_FIT
 int board_fit_config_name_match(const char *name)
 {
configs/imx8mm_beacon_defconfig +1 -8
index e37ce01c19..f6a1012d8a 100644
@@ -29,7 +29,6 @@ CONFIG_DEFAULT_FDT_FILE="imx8mm-beacon-kit.dtb"
 CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
 CONFIG_SPL_BSS_START_ADDR=0x910000
 CONFIG_SPL_BSS_MAX_SIZE=0x2000
-CONFIG_SPL_BOARD_INIT=y
 # CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
 CONFIG_SPL_STACK=0x920000
 CONFIG_SYS_SPL_MALLOC=y
@@ -88,12 +87,9 @@ CONFIG_DM_PCA953X=y
 CONFIG_DM_I2C=y
 CONFIG_SUPPORT_EMMC_BOOT=y
 CONFIG_MMC_IO_VOLTAGE=y
-CONFIG_SPL_MMC_IO_VOLTAGE=y
 CONFIG_MMC_UHS_SUPPORT=y
-CONFIG_SPL_MMC_UHS_SUPPORT=y
 CONFIG_MMC_HS400_ES_SUPPORT=y
 CONFIG_MMC_HS400_SUPPORT=y
-CONFIG_SPL_MMC_HS400_SUPPORT=y
 CONFIG_FSL_USDHC=y
 CONFIG_MTD=y
 CONFIG_DM_MTD=y
@@ -113,14 +109,12 @@ CONFIG_PINCTRL_IMX8M=y
 CONFIG_POWER_DOMAIN=y
 CONFIG_IMX8M_POWER_DOMAIN=y
 CONFIG_DM_PMIC=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
 CONFIG_DM_PMIC_BD71837=y
 CONFIG_SPL_DM_PMIC_BD71837=y
 CONFIG_DM_REGULATOR=y
-CONFIG_SPL_DM_REGULATOR=y
 CONFIG_DM_REGULATOR_BD71837=y
-CONFIG_SPL_DM_REGULATOR_BD71837=y
 CONFIG_DM_REGULATOR_FIXED=y
-CONFIG_SPL_DM_REGULATOR_FIXED=y
 CONFIG_DM_REGULATOR_GPIO=y
 CONFIG_DM_SERIAL=y
 CONFIG_MXC_UART=y
--
Quoted 2 lines

2.34.1

Adam,

Quoted 8 lines
Quoted 4 lines

I'm looking at your patches as I'm also trying to strip down the imx8mm-venice SPL so that I can fit DM USB support. It seems that all/most of the imx8m boards have a spl_board_init() which calls arch_misc_init(). I'm curious why your not calling that function?

As of right now, we're not using the CAAM which is initialized in arch_misc_init. If/When we do, we'll likely have to pull that in.

ok - makes sense.

Quoted 9 lines
Quoted 3 lines

Another config that I've found to save a lot of space for imx8m without any negative impact I can see is CONFIG_SPL_MMC_TINY=y

I experimented a bit with that too, but I hadn't fully tested switching between booting between MMC1 and MMC2, so I wasn't quite ready to enable it, but I'll spend some more time with it to see how much more space I can shave off SPL.
Getting rid of the PMIC children in SPL helped me quite a bit.

I see. It appears to save about 2K and Fabio's imx8mm clk reduction series that made it in saves another 800 bytes or so.

Quoted 7 lines
Quoted 3 lines

Regardless I'm still oversize for imx8mm-venice by 2K bytes and looking for things to prune. My issue is that I have 4 DRAM configs to support which suck up 3K each I believe.

Can you split the DRAM configs into different _defconfig files so only the DRAM config you want is built-in?

Yes that would work but I hate adding multiple firmware images. I already have issues with users selecting the wrong firmware between imx8mm/n/p as it is.

I'm thinking I should be able to move dram configs to binman blobs like was recently done with the ddr4 training blobs.

Tim

#13 lore raw
In reply to Tim Harvey
Quoted 96 lines · Tim Harvey
Quoted 74 lines · Adam Ford
Quoted 72 lines · Tim Harvey
Quoted 65 lines · Adam Ford

There are a few functions which are not essential for use in SPL, but they take up enough space to make other preferred features not fit. Remove the extras.

board/beacon/imx8mm/spl.c +0 -5
index a93cc93878..b0e9d918da 100644
@@ -44,11 +44,6 @@ static void spl_dram_init(void)
         ddr_init(&dram_timing);
  }
 
-void spl_board_init(void)
-{
-       debug("Normal Boot\n");
-}
-
  #ifdef CONFIG_SPL_LOAD_FIT
  int board_fit_config_name_match(const char *name)
  {
configs/imx8mm_beacon_defconfig +1 -8
index e37ce01c19..f6a1012d8a 100644
@@ -29,7 +29,6 @@ CONFIG_DEFAULT_FDT_FILE="imx8mm-beacon-kit.dtb"
  CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
  CONFIG_SPL_BSS_START_ADDR=0x910000
  CONFIG_SPL_BSS_MAX_SIZE=0x2000
-CONFIG_SPL_BOARD_INIT=y
  # CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
  CONFIG_SPL_STACK=0x920000
  CONFIG_SYS_SPL_MALLOC=y
@@ -88,12 +87,9 @@ CONFIG_DM_PCA953X=y
  CONFIG_DM_I2C=y
  CONFIG_SUPPORT_EMMC_BOOT=y
  CONFIG_MMC_IO_VOLTAGE=y
-CONFIG_SPL_MMC_IO_VOLTAGE=y
  CONFIG_MMC_UHS_SUPPORT=y
-CONFIG_SPL_MMC_UHS_SUPPORT=y
  CONFIG_MMC_HS400_ES_SUPPORT=y
  CONFIG_MMC_HS400_SUPPORT=y
-CONFIG_SPL_MMC_HS400_SUPPORT=y
  CONFIG_FSL_USDHC=y
  CONFIG_MTD=y
  CONFIG_DM_MTD=y
@@ -113,14 +109,12 @@ CONFIG_PINCTRL_IMX8M=y
  CONFIG_POWER_DOMAIN=y
  CONFIG_IMX8M_POWER_DOMAIN=y
  CONFIG_DM_PMIC=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
  CONFIG_DM_PMIC_BD71837=y
  CONFIG_SPL_DM_PMIC_BD71837=y
  CONFIG_DM_REGULATOR=y
-CONFIG_SPL_DM_REGULATOR=y
  CONFIG_DM_REGULATOR_BD71837=y
-CONFIG_SPL_DM_REGULATOR_BD71837=y
  CONFIG_DM_REGULATOR_FIXED=y
-CONFIG_SPL_DM_REGULATOR_FIXED=y
  CONFIG_DM_REGULATOR_GPIO=y
  CONFIG_DM_SERIAL=y
  CONFIG_MXC_UART=y
--
Quoted 2 lines

2.34.1

Adam,

Quoted 8 lines
Quoted 4 lines

I'm looking at your patches as I'm also trying to strip down the imx8mm-venice SPL so that I can fit DM USB support. It seems that all/most of the imx8m boards have a spl_board_init() which calls arch_misc_init(). I'm curious why your not calling that function?

As of right now, we're not using the CAAM which is initialized in arch_misc_init. If/When we do, we'll likely have to pull that in.

ok - makes sense.

Quoted 9 lines
Quoted 3 lines

Another config that I've found to save a lot of space for imx8m without any negative impact I can see is CONFIG_SPL_MMC_TINY=y

I experimented a bit with that too, but I hadn't fully tested switching between booting between MMC1 and MMC2, so I wasn't quite ready to enable it, but I'll spend some more time with it to see how much more space I can shave off SPL.
Getting rid of the PMIC children in SPL helped me quite a bit.

Quoted 6 lines

I see. It appears to save about 2K and Fabio's imx8mm clk reduction series that made it in saves another 800 bytes or so.

Regardless I'm still oversize for imx8mm-venice by 2K bytes and looking for things to prune. My issue is that I have 4 DRAM configs to support which suck up 3K each I believe.

Why has so many DRAM configs? Use one image to support multiple boards?

Regards,
Peng.

Quoted 2 lines

Tim

#14 lore raw
Quoted 103 lines · Peng Fan
Quoted 99 lines · Tim Harvey
Quoted 74 lines · Adam Ford
Quoted 72 lines · Tim Harvey
Quoted 65 lines · Adam Ford

There are a few functions which are not essential for use in SPL, but they take up enough space to make other preferred features not fit. Remove the extras.

board/beacon/imx8mm/spl.c +0 -5
index a93cc93878..b0e9d918da 100644
@@ -44,11 +44,6 @@ static void spl_dram_init(void)
         ddr_init(&dram_timing);
  }
 
-void spl_board_init(void)
-{
-       debug("Normal Boot\n");
-}
-
  #ifdef CONFIG_SPL_LOAD_FIT
  int board_fit_config_name_match(const char *name)
  {
configs/imx8mm_beacon_defconfig +1 -8
index e37ce01c19..f6a1012d8a 100644
@@ -29,7 +29,6 @@ CONFIG_DEFAULT_FDT_FILE="imx8mm-beacon-kit.dtb"
  CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
  CONFIG_SPL_BSS_START_ADDR=0x910000
  CONFIG_SPL_BSS_MAX_SIZE=0x2000
-CONFIG_SPL_BOARD_INIT=y
  # CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
  CONFIG_SPL_STACK=0x920000
  CONFIG_SYS_SPL_MALLOC=y
@@ -88,12 +87,9 @@ CONFIG_DM_PCA953X=y
  CONFIG_DM_I2C=y
  CONFIG_SUPPORT_EMMC_BOOT=y
  CONFIG_MMC_IO_VOLTAGE=y
-CONFIG_SPL_MMC_IO_VOLTAGE=y
  CONFIG_MMC_UHS_SUPPORT=y
-CONFIG_SPL_MMC_UHS_SUPPORT=y
  CONFIG_MMC_HS400_ES_SUPPORT=y
  CONFIG_MMC_HS400_SUPPORT=y
-CONFIG_SPL_MMC_HS400_SUPPORT=y
  CONFIG_FSL_USDHC=y
  CONFIG_MTD=y
  CONFIG_DM_MTD=y
@@ -113,14 +109,12 @@ CONFIG_PINCTRL_IMX8M=y
  CONFIG_POWER_DOMAIN=y
  CONFIG_IMX8M_POWER_DOMAIN=y
  CONFIG_DM_PMIC=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
  CONFIG_DM_PMIC_BD71837=y
  CONFIG_SPL_DM_PMIC_BD71837=y
  CONFIG_DM_REGULATOR=y
-CONFIG_SPL_DM_REGULATOR=y
  CONFIG_DM_REGULATOR_BD71837=y
-CONFIG_SPL_DM_REGULATOR_BD71837=y
  CONFIG_DM_REGULATOR_FIXED=y
-CONFIG_SPL_DM_REGULATOR_FIXED=y
  CONFIG_DM_REGULATOR_GPIO=y
  CONFIG_DM_SERIAL=y
  CONFIG_MXC_UART=y
--
Quoted 2 lines

2.34.1

Adam,

Quoted 8 lines
Quoted 4 lines

I'm looking at your patches as I'm also trying to strip down the imx8mm-venice SPL so that I can fit DM USB support. It seems that all/most of the imx8m boards have a spl_board_init() which calls arch_misc_init(). I'm curious why your not calling that function?

As of right now, we're not using the CAAM which is initialized in arch_misc_init. If/When we do, we'll likely have to pull that in.

ok - makes sense.

Quoted 9 lines
Quoted 3 lines

Another config that I've found to save a lot of space for imx8m without any negative impact I can see is CONFIG_SPL_MMC_TINY=y

I experimented a bit with that too, but I hadn't fully tested switching between booting between MMC1 and MMC2, so I wasn't quite ready to enable it, but I'll spend some more time with it to see how much more space I can shave off SPL.
Getting rid of the PMIC children in SPL helped me quite a bit.

I see. It appears to save about 2K and Fabio's imx8mm clk reduction series that made it in saves another 800 bytes or so.

Quoted 9 lines
Quoted 3 lines

Regardless I'm still oversize for imx8mm-venice by 2K bytes and looking for things to prune. My issue is that I have 4 DRAM configs to support which suck up 3K each I believe.

Why has so many DRAM configs? Use one image to support multiple boards?

Regards,
Peng.

Peng,

Yes, imx8mm_venice_defconfig covers 6 different dtbs and 4 different DRAM configs (512MiB, 1GiB, 2GiB, 4GiB) which bloats the SPL to the point that I can't add SDP support... specifically DM USB.

Tim

#15 lore raw

PATCH 1/3 imx: imx8mm_beacon: Eliminate a few extras to free up SPL space

In reply to Adam Ford
Quoted 52 lines

There are a few functions which are not essential for use in SPL, but they take up enough space to make other preferred features not fit. Remove the extras.

board/beacon/imx8mm/spl.c +0 -5
index a93cc93878..b0e9d918da 100644
@@ -44,11 +44,6 @@ static void spl_dram_init(void)
 	ddr_init(&dram_timing);
 }
 
-void spl_board_init(void)
-{
-	debug("Normal Boot\n");
-}
-
 #ifdef CONFIG_SPL_LOAD_FIT
 int board_fit_config_name_match(const char *name)
 {
configs/imx8mm_beacon_defconfig +1 -4
index e37ce01c19..f6a1012d8a 100644
@@ -29,7 +29,6 @@ CONFIG_DEFAULT_FDT_FILE="imx8mm-beacon-kit.dtb"
 CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
 CONFIG_SPL_BSS_START_ADDR=0x910000
 CONFIG_SPL_BSS_MAX_SIZE=0x2000
-CONFIG_SPL_BOARD_INIT=y
 # CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
 CONFIG_SPL_STACK=0x920000
 CONFIG_SYS_SPL_MALLOC=y
@@ -88,12 +87,9 @@ CONFIG_DM_PCA953X=y
 CONFIG_DM_I2C=y
 CONFIG_SUPPORT_EMMC_BOOT=y
 CONFIG_MMC_IO_VOLTAGE=y
-CONFIG_SPL_MMC_IO_VOLTAGE=y
 CONFIG_MMC_UHS_SUPPORT=y
-CONFIG_SPL_MMC_UHS_SUPPORT=y
 CONFIG_MMC_HS400_ES_SUPPORT=y
 CONFIG_MMC_HS400_SUPPORT=y
-CONFIG_SPL_MMC_HS400_SUPPORT=y
 CONFIG_FSL_USDHC=y
 CONFIG_MTD=y
 CONFIG_DM_MTD=y
@@ -113,14 +109,12 @@ CONFIG_PINCTRL_IMX8M=y
 CONFIG_POWER_DOMAIN=y
 CONFIG_IMX8M_POWER_DOMAIN=y
 CONFIG_DM_PMIC=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
 CONFIG_DM_PMIC_BD71837=y

configs/imx8mm_beacon_defconfig CONFIG_PINCTRL_IMX8M=y · line 120

Quoted 10 lines
configs/imx8mm_beacon_defconfig +0 -3
 CONFIG_SPL_DM_PMIC_BD71837=y
 CONFIG_DM_REGULATOR=y
-CONFIG_SPL_DM_REGULATOR=y
 CONFIG_DM_REGULATOR_BD71837=y
-CONFIG_SPL_DM_REGULATOR_BD71837=y
 CONFIG_DM_REGULATOR_FIXED=y
-CONFIG_SPL_DM_REGULATOR_FIXED=y
 CONFIG_DM_REGULATOR_GPIO=y
 CONFIG_DM_SERIAL=y
 CONFIG_MXC_UART=y

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================