serial: 8250: 8250_omap: Avoid RS485 RTS glitch on ->set_termios()
Subsystems (6)
Sasha Levin
maintainerPATCH 1/5 serial: 8250: 8250_omap: Avoid RS485 RTS glitch on ->set_termios()
From: Lukas Wunner <[email protected]>
[ Upstream commit 038ee49fef18710bedd38b531d173ccd746b2d8d ]
RS485-enabled UART ports on TI Sitara SoCs with active-low polarity exhibit a Transmit Enable glitch on ->set_termios():
omap8250_restore_regs(), which is called from omap_8250_set_termios(), sets the TCRTLR bit in the MCR register and clears all other bits, including RTS. If RTS uses active-low polarity, it is now asserted for no reason.
The TCRTLR bit is subsequently cleared by writing up->mcr to the MCR register. That variable is always zero, so the RTS bit is still cleared (incorrectly so if RTS is active-high).
(up->mcr is not, as one might think, a cache of the MCR register's current value. Rather, it only caches a single bit of that register, the AFE bit. And it only does so if the UART supports the AFE bit, which OMAP does not. For details see serial8250_do_set_termios() and serial8250_do_set_mctrl().)
Finally at the end of omap8250_restore_regs(), the MCR register is restored (and RTS deasserted) by a call to up->port.ops->set_mctrl() (which equals serial8250_set_mctrl()) and serial8250_em485_stop_tx().
So there's an RTS glitch between setting TCRTLR and calling serial8250_em485_stop_tx(). Avoid by using a read-modify-write when setting TCRTLR.
While at it, drop a redundant initialization of up->mcr. As explained above, the variable isn't used by the driver and it is already initialized to zero because it is part of the static struct serial8250_ports[] declared in 8250_core.c. (Static structs are initialized to zero per section 6.7.8 nr. 10 of the C99 standard.)
--- drivers/tty/serial/8250/8250_omap.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)
drivers/tty/serial/8250/8250_omap.c +4 -3
@@ -259,6 +259,7 @@ static void omap8250_restore_regs(struct uart_8250_port *up) {struct omap8250_priv *priv = up->port.private_data;struct uart_8250_dma *dma = up->dma; +u8 mcr =serial8250_in_MCR (up);if (dma && dma->tx_running) {/*
@@ -275,7 +276,7 @@ static void omap8250_restore_regs(struct uart_8250_port *up)serial_out (up,UART_EFR ,UART_EFR_ECB );serial_out (up,UART_LCR ,UART_LCR_CONF_MODE_A ); -serial8250_out_MCR (up,UART_MCR_TCRTLR ); +serial8250_out_MCR (up, mcr |UART_MCR_TCRTLR );serial_out (up,UART_FCR , up->fcr);omap8250_update_scr (up, priv);
@@ -291,7 +292,8 @@ static void omap8250_restore_regs(struct uart_8250_port *up)serial_out (up,UART_LCR ,0 );/* drop TCR + TLR access, we setup XON/XOFF later */ -serial8250_out_MCR (up, up->mcr); +serial8250_out_MCR (up, mcr); +serial_out (up,UART_IER , up->ier);serial_out (up,UART_LCR ,UART_LCR_CONF_MODE_B );
@@ -600,7 +602,6 @@ static int omap_8250_startup(struct uart_port *port)pm_runtime_get_sync (port->dev); - up->mcr =0 ;serial_out (up,UART_FCR ,UART_FCR_CLEAR_RCVR |UART_FCR_CLEAR_XMIT );serial_out (up,UART_LCR ,UART_LCR_WLEN8 );
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 2/5 xen/platform-pci: add missing free_irq() in error path
From: ruanjinjie <[email protected]>
[ Upstream commit c53717e1e3f0d0f9129b2e0dbc6dcc5e0a8132e9 ]
free_irq() is missing in case of error in platform_pci_probe(), fix that.
--- drivers/xen/platform-pci.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-)
drivers/xen/platform-pci.c +5 -2
@@ -149,7 +149,7 @@ static int platform_pci_probe(struct pci_dev *pdev,if (ret) {dev_warn (&pdev->dev,"Unable to set the evtchn callback " "err=%d\n" , ret); - goto out; + goto irq_out; } }
@@ -157,7 +157,7 @@ static int platform_pci_probe(struct pci_dev *pdev, grant_frames =alloc_xen_mmio (PAGE_SIZE * max_nr_gframes); ret =gnttab_setup_auto_xlat_frames (grant_frames);if (ret) - goto out; + goto irq_out; ret =gnttab_init ();if (ret) goto grant_out;
@@ -165,6 +165,9 @@ static int platform_pci_probe(struct pci_dev *pdev,return 0 ; grant_out:gnttab_free_auto_xlat_frames (); +irq_out: +if (!xen_have_vector_callback) +free_irq (pdev->irq, pdev); out:pci_release_region (pdev,0 ); mem_out:
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 3/5 platform/x86: asus-wmi: add missing pci_dev_put() in asus_wmi_set_xusb2pr()
In reply to Sasha LevinFrom: Xiongfeng Wang <[email protected]>
[ Upstream commit d0cdd85046b15089df71a50548617ac1025300d0 ]
pci_get_device() will increase the reference count for the returned pci_dev. We need to use pci_dev_put() to decrease the reference count before asus_wmi_set_xusb2pr() returns.
--- drivers/platform/x86/asus-wmi.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/platform/x86/asus-wmi.c +2 -0
@@ -1111,6 +1111,8 @@ static void asus_wmi_set_xusb2pr(struct asus_wmi *asus)pci_write_config_dword (xhci_pdev,USB_INTEL_XUSB2PR ,cpu_to_le32 (ports_available)); +pci_dev_put (xhci_pdev); +pr_info ("set USB_INTEL_XUSB2PR old: 0x%04x, new: 0x%04x\n" , orig_ports_available, ports_available); }
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 4/5 tcp: configurable source port perturb table size
In reply to Sasha LevinFrom: Gleb Mazovetskiy <[email protected]>
[ Upstream commit aeac4ec8f46d610a10adbaeff5e2edf6a88ffc62 ]
On embedded systems with little memory and no relevant security concerns, it is beneficial to reduce the size of the table.
Reducing the size from 2^16 to 2^8 saves 255 KiB of kernel RAM.
Makes the table size configurable as an expert option.
The size was previously increased from 2^8 to 2^16
in commit 4c2c8f03a5ab ("tcp: increase source port perturb table to 2^16").
--- net/ipv4/Kconfig | 10 ++++++++++ net/ipv4/inet_hashtables.c | 10 +++++----- 2 files changed, 15 insertions(+), 5 deletions(-)
net/ipv4/Kconfig +10 -0
@@ -371,6 +371,16 @@ config INET_IPCOMP If unsure, say Y. +config INET_TABLE_PERTURB_ORDER + int "INET: Source port perturbation table size (as power of 2)" if EXPERT + default 16 + help + Source port perturbation table size (as power of 2) for + RFC 6056 3.3.4. Algorithm 4: Double-Hash Port Selection Algorithm. + + The default is almost always what you want. + Only change this if you know what you are doing. + config INET_XFRM_TUNNEL tristate select INET_TUNNEL
net/ipv4/inet_hashtables.c +5 -5
@@ -541,13 +541,13 @@ EXPORT_SYMBOL_GPL(inet_unhash);* Note that we use 32bit integers (vs RFC 'short integers') * because 2^16 is not a multiple of num_ephemeral and this * property might be used by clever attacker. +* * RFC claims using TABLE_LENGTH=10 buckets gives an improvement, though -* attacks were since demonstrated, thus we use 65536 instead to really -* give more isolation and privacy, at the expense of 256kB of kernel -* memory. +* attacks were since demonstrated, thus we use 65536 by default instead +* to really give more isolation and privacy, at the expense of 256kB +* of kernel memory. */ -#define INET_TABLE_PERTURB_SHIFT 16 -#define INET_TABLE_PERTURB_SIZE (1 << INET_TABLE_PERTURB_SHIFT) +#define INET_TABLE_PERTURB_SIZE (1 << CONFIG_INET_TABLE_PERTURB_ORDER)static u32 *table_perturb; int __inet_hash_connect(struct inet_timewait_death_row *death_row,
Signature · 1 line
2.35.1
Sasha Levin
maintainerPATCH 5/5 net: usb: qmi_wwan: add Telit 0x103a composition
In reply to Sasha LevinFrom: Enrico Sau <[email protected]>
[ Upstream commit e103ba33998d0f25653cc8ebe745b68d1ee10cda ]
Add the following Telit LE910C4-WWX composition:
0x103a: rmnet
--- drivers/net/usb/qmi_wwan.c | 1 + 1 file changed, 1 insertion(+)
drivers/net/usb/qmi_wwan.c +1 -0
@@ -926,6 +926,7 @@ static const struct usb_device_id products[] = { {QMI_FIXED_INTF(0x2357, 0x0201, 4)}, /* TP-LINK HSUPA Modem MA180 */ {QMI_FIXED_INTF(0x2357, 0x9000, 4)}, /* TP-LINK MA260 */ {QMI_QUIRK_SET_DTR(0x1bc7, 0x1031, 3)}, /* Telit LE910C1-EUX */ + {QMI_QUIRK_SET_DTR(0x1bc7, 0x103a, 0)}, /* Telit LE910C4-WWX */ {QMI_QUIRK_SET_DTR(0x1bc7, 0x1040, 2)}, /* Telit LE922A */ {QMI_QUIRK_SET_DTR(0x1bc7, 0x1050, 2)}, /* Telit FN980 */ {QMI_QUIRK_SET_DTR(0x1bc7, 0x1060, 2)}, /* Telit LN920 */
Signature · 1 line
2.35.1