configs/imxrt1050-evk: New defconfig
PATCH v4 1/1 configs/imxrt1050-evk: New defconfig
Add defconfig for imxrt1050-evk is a development board from NXP.
Giulio and I worked on Linux and U-boot for this board. And now I'm adding support for the new board in Buildroot.
The i.MXRTxxxx family spreads from i.MXRT1020 to i.MXRT1170 with the first one supporting 1 USB OTG & 100M ethernet with a cortex-M7@500Mhz up to the latter with i.MXRT1170 with cortex-M7@1Ghz and cortex-M4@400Mhz, 2MB of internal SRAM, 2D GPU, 2x 1Gb and 1x 100Mb ENET. The i.MXRT family is NXP's answer to STM32F7xx, as it uses only simple SDRAM, it gives the chance of a 4 or less layer PCBs. Seeing that these chips are comparable to the STM32F7xxs which have buildroot ported to them it seems reasonable to add support for them.
--- DEVELOPERS | 6 +++ board/freescale/imxrt1050evk/genimage.cfg | 40 +++++++++++++++++++ board/freescale/imxrt1050evk/post-build.sh | 3 ++ board/freescale/imxrt1050evk/readme.txt | 30 ++++++++++++++ board/freescale/imxrt1050evk/uboot.fragment | 2 + configs/imxrt1050-evk_defconfig | 43 +++++++++++++++++++++ 6 files changed, 124 insertions(+) create mode 100644 board/freescale/imxrt1050evk/genimage.cfg create mode 100755 board/freescale/imxrt1050evk/post-build.sh create mode 100644 board/freescale/imxrt1050evk/readme.txt create mode 100644 board/freescale/imxrt1050evk/uboot.fragment create mode 100644 configs/imxrt1050-evk_defconfig
DEVELOPERS +6 -0
@@ -1132,9 +1132,11 @@ F: package/webp/ F: package/xapian/ N: Giulio Benetti <[email protected]> +F: board/freescale/imxrt1050evk/* F: board/olimex/a* F: configs/amarula_vyasa_rk3288_defconfig F: configs/asus_tinker_rk3288_defconfig +F: configs/imxrt1050-evk_defconfig F: configs/olimex_a* F: package/at/ F: package/binutils/
@@ -1477,6 +1479,10 @@ F: package/wmctrl/ F: package/x11r7/xdriver_xf86-video-imx/ F: package/x11r7/xdriver_xf86-video-imx-viv/ +N: Jesse Taube <[email protected]> +F: board/freescale/imxrt1050evk/* +F: configs/imxrt1050-evk_defconfig + N: Jesse Van Gavere <[email protected]> F: package/qt6/qt6serialport/
board/freescale/imxrt1050evk/genimage.cfg new file +40 -0
@@ -0,0 +1,40 @@ +image boot.vfat { + vfat { + files = { + "uImage", + "imxrt1050-evk.dtb", + } + } + + size = 6M +} + +image sdcard.img { + hdimage { + } + + partition SPL { + in-partition-table = "no" + image = "SPL" + offset = 1K + size = 127K + } + + partition u-boot { + in-partition-table = "no" + image = "u-boot.img" + offset = 128K + size = 512K + } + + partition boot { + partition-type = 0xc + bootable = "true" + image = "boot.vfat" + } + + partition rootfs { + partition-type = 0x83 + image = "rootfs.ext4" + } +}
board/freescale/imxrt1050evk/post-build.sh new file +3 -0
@@ -0,0 +1,3 @@ +#!/bin/sh +MKIMAGE=$HOST_DIR/bin/mkimage +$MKIMAGE -A arm -O linux -T kernel -C none -a 0x80008000 -e 0x80008000 -n "Linux kernel" -d $BINARIES_DIR/Image $BINARIES_DIR/uImage
board/freescale/imxrt1050evk/readme.txt new file +30 -0
@@ -0,0 +1,30 @@ +NXP i.MXRT1050 EVK board +------------------------ + +i.MX RT1050 are NXP's crossover MCUs. They combine the high performance and high +level of integration of an applications processors with the ease-of-use and +real-time functionality of a microcontroller. The i.MX RT1050 MCU runs on the Arm +Cortex-M7 core at 600 MHz. +https://www.nxp.com/design/development-boards/i-mx-evaluation-and-development-boards/i-mx-rt1050-evaluation-kit:MIMXRT1050-EVK + +To build a minimal support for this board: + +$ make imxrt1050-evk_defconfig +$ make + +Buildroot prepares a bootable "sdcard.img" image in the output/images/ +directory, ready to be flashed into the SD card: + +$ dd if=output/images/sdcard.img of=/dev/sdX +Where 'sdX' is the device node of the uSD. + +Jumper settings: + + SW7: 1 0 1 0 + +Where 0 means bottom position and 1 means top position (from the +switch label numbers reference). + +Connect the USB cable between the EVK and the PC for the console. + +Insert the micro SD card in the board, power it up and U-Boot messages should come up.
board/freescale/imxrt1050evk/uboot.fragment new file +2 -0
@@ -0,0 +1,2 @@ +CONFIG_USE_BOOTCOMMAND=y +CONFIG_BOOTCOMMAND="setenv bootargs console=ttyLP0 root=/dev/mmcblk0p2 rw earlycon rootwait;load mmc 0:1 0x80800000 imxrt1050-evk.dtb;load mmc 0:1 0x80000000 uImage;bootm 0x80000000 - 0x80800000"
configs/imxrt1050-evk_defconfig new file +43 -0
43 lines not on this page · raw message
Signature · 6 lines
2.38.1 _______________________________________________ buildroot mailing list [email protected] https://lists.buildroot.org/mailman/listinfo/buildroot
Quoted 186 lines · Jesse Taube
Add defconfig for imxrt1050-evk is a development board from NXP.
Giulio and I worked on Linux and U-boot for this board. And now I'm adding support for the new board in Buildroot.
The i.MXRTxxxx family spreads from i.MXRT1020 to i.MXRT1170 with the first one supporting 1 USB OTG & 100M ethernet with a cortex-M7@500Mhz up to the latter with i.MXRT1170 with cortex-M7@1Ghz and cortex-M4@400Mhz, 2MB of internal SRAM, 2D GPU, 2x 1Gb and 1x 100Mb ENET. The i.MXRT family is NXP's answer to STM32F7xx, as it uses only simple SDRAM, it gives the chance of a 4 or less layer PCBs. Seeing that these chips are comparable to the STM32F7xxs which have buildroot ported to them it seems reasonable to add support for them.
Signed-off-by Jesse Taube <[email protected]>Cc Giulio Benetti <[email protected]>--- DEVELOPERS | 6 +++ board/freescale/imxrt1050evk/genimage.cfg | 40 +++++++++++++++++++ board/freescale/imxrt1050evk/post-build.sh | 3 ++ board/freescale/imxrt1050evk/readme.txt | 30 ++++++++++++++ board/freescale/imxrt1050evk/uboot.fragment | 2 + configs/imxrt1050-evk_defconfig | 43 +++++++++++++++++++++ 6 files changed, 124 insertions(+)create mode 100644 board/freescale/imxrt1050evk/genimage.cfg create mode 100755
board/freescale/imxrt1050evk/post-build.shcreate mode 100644board/freescale/imxrt1050evk/readme.txtcreate mode 100644 board/freescale/imxrt1050evk/uboot.fragment create mode 100644 configs/imxrt1050-evk_defconfigDEVELOPERS +6
-0@@ -1132,9 +1132,11 @@ F: package/webp/ F: package/xapian/ N: Giulio Benetti <[email protected]> +F: board/freescale/imxrt1050evk/* F: board/olimex/a* F: configs/amarula_vyasa_rk3288_defconfig F: configs/asus_tinker_rk3288_defconfig +F: configs/imxrt1050-evk_defconfig F: configs/olimex_a* F: package/at/ F: package/binutils/@@ -1477,6 +1479,10 @@ F: package/wmctrl/ F: package/x11r7/xdriver_xf86-video-imx/ F: package/x11r7/xdriver_xf86-video-imx-viv/ +N: Jesse Taube <[email protected]> +F: board/freescale/imxrt1050evk/* +F: configs/imxrt1050-evk_defconfig + N: Jesse Van Gavere <[email protected]> F: package/qt6/qt6serialport/board/freescale/imxrt1050evk/genimage.cfg new file +40
-0@@ -0,0 +1,40 @@ +image boot.vfat { + vfat { + files = { + "uImage", + "imxrt1050-evk.dtb", + } + } + + size = 6M +} + +image sdcard.img { + hdimage { + } + + partition SPL { + in-partition-table = "no" + image = "SPL" + offset = 1K + size = 127K + } + + partition u-boot { + in-partition-table = "no" + image = "u-boot.img" + offset = 128K + size = 512K + } + + partition boot { + partition-type = 0xc + bootable = "true" + image = "boot.vfat" + } + + partition rootfs { + partition-type = 0x83 + image = "rootfs.ext4" + } +}board/freescale/imxrt1050evk/post-build.sh new file +3
-0@@ -0,0 +1,3 @@ +#!/bin/sh +MKIMAGE=$HOST_DIR/bin/mkimage +$MKIMAGE -A arm -O linux -T kernel -C none -a 0x80008000 -e 0x80008000 -n "Linux kernel" -d $BINARIES_DIR/Image $BINARIES_DIR/uImageboard/freescale/imxrt1050evk/readme.txt new file +30
-0@@ -0,0 +1,30 @@ +NXP i.MXRT1050 EVK board +------------------------ + +i.MX RT1050 are NXP's crossover MCUs. They combine the high performance and high +level of integration of an applications processors with the ease-of-use and +real-time functionality of a microcontroller. The i.MX RT1050 MCU runs on the Arm +Cortex-M7 core at 600 MHz. +https://www.nxp.com/design/development-boards/i-mx-evaluation-and-development-boards/i-mx-rt1050-evaluation-kit:MIMXRT1050-EVK + +To build a minimal support for this board: + +$ make imxrt1050-evk_defconfig +$ make + +Buildroot prepares a bootable "sdcard.img" image in the output/images/ +directory, ready to be flashed into the SD card: + +$ dd if=output/images/sdcard.img of=/dev/sdX +Where 'sdX' is the device node of the uSD. + +Jumper settings: + + SW7: 1 0 1 0 + +Where 0 means bottom position and 1 means top position (from the +switch label numbers reference). + +Connect the USB cable between the EVK and the PC for the console. + +Insert the micro SD card in the board, power it up and U-Boot messages should come up.board/freescale/imxrt1050evk/uboot.fragment new file +2
-0@@ -0,0 +1,2 @@ +CONFIG_USE_BOOTCOMMAND=y +CONFIG_BOOTCOMMAND="setenv bootargs console=ttyLP0 root=/dev/mmcblk0p2 rw earlycon rootwait;load mmc 0:1 0x80800000 imxrt1050-evk.dtb;load mmc 0:1 0x80000000 uImage;bootm 0x80000000 - 0x80800000"configs/imxrt1050-evk_defconfig new file +22
-0@@ -0,0 +1,43 @@ +# Architecture +BR2_arm=y +BR2_cortex_m7=y + +# Image +BR2_ROOTFS_POST_BUILD_SCRIPT="board/freescale/imxrt1050evk/post-build.sh" +BR2_ROOTFS_POST_IMAGE_SCRIPT="support/scripts/genimage.sh" +BR2_ROOTFS_POST_SCRIPT_ARGS="-c board/freescale/imxrt1050evk/genimage.cfg" + +# Kernel +BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_CUSTOM_VERSION=y +BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="6.1" +BR2_LINUX_KERNEL_DEFCONFIG="imxrt" +BR2_LINUX_KERNEL_IMAGE_TARGET_CUSTOM=y +BR2_LINUX_KERNEL_IMAGE_TARGET_NAME="Image" +BR2_LINUX_KERNEL_IMAGE_NAME="Image" +BR2_LINUX_KERNEL_DTS_SUPPORT=y +BR2_LINUX_KERNEL_INTREE_DTS_NAME="imxrt1050-evk" + +# Filesystem +BR2_TARGET_ROOTFS_EXT2=y
configs/imxrt1050-evk_defconfig line 32
Quoted 10 lines
configs/imxrt1050-evk_defconfig new file +10
-0+BR2_TARGET_ROOTFS_EXT2_4=y +BR2_TARGET_ROOTFS_EXT2_SIZE="3M" + + +# Bootloader +BR2_TARGET_UBOOT=y +BR2_TARGET_UBOOT_BOARDNAME="imxrt1050-evk" +BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y +BR2_TARGET_UBOOT_CUSTOM_VERSION=y +BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2022.11"
should have been 2022.10 I don't know if the committer will change this or not
Thanks,
Jesse Taube
configs/imxrt1050-evk_defconfig line 43
Quoted 11 lines
configs/imxrt1050-evk_defconfig new file +11
-0+BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imxrt1050-evk" +BR2_TARGET_UBOOT_CONFIG_FRAGMENT_FILES="board/freescale/imxrt1050evk/uboot.fragment" +BR2_TARGET_UBOOT_FORMAT_IMG=y +BR2_TARGET_UBOOT_SPL=y +BR2_TARGET_UBOOT_SPL_NAME="SPL" +BR2_TARGET_UBOOT_NEEDS_OPENSSL=y + +# Required tools to create the SD card image +BR2_PACKAGE_HOST_GENIMAGE=y +BR2_PACKAGE_HOST_MKPASSWD=y +BR2_PACKAGE_HOST_UBOOT_TOOLS=y
_______________________________________________
buildroot mailing list
[email protected]
https://lists.buildroot.org/mailman/listinfo/buildroot
Hi Jesse,
Quoted 65 lines · Jesse Taube
Add defconfig for imxrt1050-evk is a development board from NXP.
Giulio and I worked on Linux and U-boot for this board. And now I'm adding support for the new board in Buildroot.
The i.MXRTxxxx family spreads from i.MXRT1020 to i.MXRT1170 with the first one supporting 1 USB OTG & 100M ethernet with a cortex-M7@500Mhz up to the latter with i.MXRT1170 with cortex-M7@1Ghz and cortex-M4@400Mhz, 2MB of internal SRAM, 2D GPU, 2x 1Gb and 1x 100Mb ENET. The i.MXRT family is NXP's answer to STM32F7xx, as it uses only simple SDRAM, it gives the chance of a 4 or less layer PCBs. Seeing that these chips are comparable to the STM32F7xxs which have buildroot ported to them it seems reasonable to add support for them.
Signed-off-by Jesse Taube <[email protected]>Cc Giulio Benetti <[email protected]>--- DEVELOPERS | 6 +++ board/freescale/imxrt1050evk/genimage.cfg | 40 +++++++++++++++++++ board/freescale/imxrt1050evk/post-build.sh | 3 ++ board/freescale/imxrt1050evk/readme.txt | 30 ++++++++++++++ board/freescale/imxrt1050evk/uboot.fragment | 2 + configs/imxrt1050-evk_defconfig | 43 +++++++++++++++++++++ 6 files changed, 124 insertions(+)create mode 100644 board/freescale/imxrt1050evk/genimage.cfg create mode 100755
board/freescale/imxrt1050evk/post-build.shcreate mode 100644board/freescale/imxrt1050evk/readme.txtcreate mode 100644 board/freescale/imxrt1050evk/uboot.fragment create mode 100644 configs/imxrt1050-evk_defconfigDEVELOPERS +6
-0@@ -1132,9 +1132,11 @@ F: package/webp/ F: package/xapian/ N: Giulio Benetti <[email protected]> +F: board/freescale/imxrt1050evk/* F: board/olimex/a* F: configs/amarula_vyasa_rk3288_defconfig F: configs/asus_tinker_rk3288_defconfig +F: configs/imxrt1050-evk_defconfig F: configs/olimex_a* F: package/at/ F: package/binutils/@@ -1477,6 +1479,10 @@ F: package/wmctrl/ F: package/x11r7/xdriver_xf86-video-imx/ F: package/x11r7/xdriver_xf86-video-imx-viv/ +N: Jesse Taube <[email protected]> +F: board/freescale/imxrt1050evk/* +F: configs/imxrt1050-evk_defconfig + N: Jesse Van Gavere <[email protected]> F: package/qt6/qt6serialport/board/freescale/imxrt1050evk/genimage.cfg new file +0
-0
board/freescale/imxrt1050evk/genimage.cfg line 9
Quoted 9 lines
board/freescale/imxrt1050evk/genimage.cfg new file +9
-0@@ -0,0 +1,40 @@ +image boot.vfat { + vfat { + files = { + "uImage", + "imxrt1050-evk.dtb", + } + } + + size = 6M
Please round it up to 8M, 6M is pretty odd and we have an sd-card here to use, so plenty of space. If someone wants to shrink it down it can do it later.
Quoted 37 lines
board/freescale/imxrt1050evk/genimage.cfg new file +31
-0+} + +image sdcard.img { + hdimage { + } + + partition SPL { + in-partition-table = "no" + image = "SPL" + offset = 1K + size = 127K + } + + partition u-boot { + in-partition-table = "no" + image = "u-boot.img" + offset = 128K + size = 512K + } + + partition boot { + partition-type = 0xc + bootable = "true" + image = "boot.vfat" + } + + partition rootfs { + partition-type = 0x83 + image = "rootfs.ext4" + } +}board/freescale/imxrt1050evk/post-build.sh new file +0
-0
board/freescale/imxrt1050evk/post-build.sh line 3
Quoted 3 lines
board/freescale/imxrt1050evk/post-build.sh new file +3
-0@@ -0,0 +1,3 @@ +#!/bin/sh +MKIMAGE=$HOST_DIR/bin/mkimage +$MKIMAGE -A arm -O linux -T kernel -C none -a 0x80008000 -e 0x80008000 -n "Linux kernel" -d $BINARIES_DIR/Image $BINARIES_DIR/uImage
You can drop post-build.sh file because you can already produce uImage, see below
Quoted 50 lines
board/freescale/imxrt1050evk/readme.txt new file +30
-0@@ -0,0 +1,30 @@ +NXP i.MXRT1050 EVK board +------------------------ + +i.MX RT1050 are NXP's crossover MCUs. They combine the high performance and high +level of integration of an applications processors with the ease-of-use and +real-time functionality of a microcontroller. The i.MX RT1050 MCU runs on the Arm +Cortex-M7 core at 600 MHz. +https://www.nxp.com/design/development-boards/i-mx-evaluation-and-development-boards/i-mx-rt1050-evaluation-kit:MIMXRT1050-EVK + +To build a minimal support for this board: + +$ make imxrt1050-evk_defconfig +$ make + +Buildroot prepares a bootable "sdcard.img" image in the output/images/ +directory, ready to be flashed into the SD card: + +$ dd if=output/images/sdcard.img of=/dev/sdX +Where 'sdX' is the device node of the uSD. + +Jumper settings: + + SW7: 1 0 1 0 + +Where 0 means bottom position and 1 means top position (from the +switch label numbers reference). + +Connect the USB cable between the EVK and the PC for the console. + +Insert the micro SD card in the board, power it up and U-Boot messages should come up.board/freescale/imxrt1050evk/uboot.fragment new file +2
-0@@ -0,0 +1,2 @@ +CONFIG_USE_BOOTCOMMAND=y +CONFIG_BOOTCOMMAND="setenv bootargs console=ttyLP0 root=/dev/mmcblk0p2 rw earlycon rootwait;load mmc 0:1 0x80800000 imxrt1050-evk.dtb;load mmc 0:1 0x80000000 uImage;bootm 0x80000000 - 0x80800000"configs/imxrt1050-evk_defconfig new file +0
-0
configs/imxrt1050-evk_defconfig line 6
Quoted 6 lines
configs/imxrt1050-evk_defconfig new file +6
-0@@ -0,0 +1,43 @@ +# Architecture +BR2_arm=y +BR2_cortex_m7=y + +# Image +BR2_ROOTFS_POST_BUILD_SCRIPT="board/freescale/imxrt1050evk/post-build.sh"
Please drop this ^^^
configs/imxrt1050-evk_defconfig line 15
Quoted 9 lines
configs/imxrt1050-evk_defconfig new file +9
-0+BR2_ROOTFS_POST_IMAGE_SCRIPT="support/scripts/genimage.sh" +BR2_ROOTFS_POST_SCRIPT_ARGS="-c board/freescale/imxrt1050evk/genimage.cfg" + +# Kernel +BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_CUSTOM_VERSION=y +BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="6.1" +BR2_LINUX_KERNEL_DEFCONFIG="imxrt" +BR2_LINUX_KERNEL_IMAGE_TARGET_CUSTOM=y
Drop this ^^^
configs/imxrt1050-evk_defconfig line 16
Quoted 1 line
configs/imxrt1050-evk_defconfig new file +1
-0+BR2_LINUX_KERNEL_IMAGE_TARGET_NAME="Image"
and this ^^^
configs/imxrt1050-evk_defconfig line 17
Quoted 1 line
configs/imxrt1050-evk_defconfig new file +1
-0+BR2_LINUX_KERNEL_IMAGE_NAME="Image"
and this ^^^
in favor of:
BR2_LINUX_KERNEL_UIMAGE=y
it works even without specifying the address since the default is used that is exactly 0x80008000, the same used by post-build.sh that becomes useless.
configs/imxrt1050-evk_defconfig line 24
Quoted 7 lines
configs/imxrt1050-evk_defconfig new file +7
-0+BR2_LINUX_KERNEL_DTS_SUPPORT=y +BR2_LINUX_KERNEL_INTREE_DTS_NAME="imxrt1050-evk" + +# Filesystem +BR2_TARGET_ROOTFS_EXT2=y +BR2_TARGET_ROOTFS_EXT2_4=y +BR2_TARGET_ROOTFS_EXT2_SIZE="3M"
Please expand the rootfs size to 16M at least, 3M is odd and this is the result of 'df -h':
Filesystem Size Used Available Use% Mounted on
/dev/root 1.8M 537.0K 1.1M 33% /
I would like to have more than 1.1M to do tests.
configs/imxrt1050-evk_defconfig line 29
Quoted 5 lines
configs/imxrt1050-evk_defconfig new file +5
-0+ + +# Bootloader +BR2_TARGET_UBOOT=y +BR2_TARGET_UBOOT_BOARDNAME="imxrt1050-evk"
While make savedefconfig this ^^^ becomes useless. BR2_TARGET_UBOOT_BOARD_DEFCONFIG is enough. So please drop it
configs/imxrt1050-evk_defconfig line 32
Quoted 3 lines
configs/imxrt1050-evk_defconfig new file +3
-0+BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y +BR2_TARGET_UBOOT_CUSTOM_VERSION=y +BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2022.11"
As you've already pointed here you need 2022.10
configs/imxrt1050-evk_defconfig line 43
Quoted 11 lines
configs/imxrt1050-evk_defconfig new file +11
-0+BR2_TARGET_UBOOT_BOARD_DEFCONFIG="imxrt1050-evk" +BR2_TARGET_UBOOT_CONFIG_FRAGMENT_FILES="board/freescale/imxrt1050evk/uboot.fragment" +BR2_TARGET_UBOOT_FORMAT_IMG=y +BR2_TARGET_UBOOT_SPL=y +BR2_TARGET_UBOOT_SPL_NAME="SPL" +BR2_TARGET_UBOOT_NEEDS_OPENSSL=y + +# Required tools to create the SD card image +BR2_PACKAGE_HOST_GENIMAGE=y +BR2_PACKAGE_HOST_MKPASSWD=y +BR2_PACKAGE_HOST_UBOOT_TOOLS=y
Please drop this ^^^ too since now uImage is generated by Linux package.
I've tested this on the imxrt1050-evk but there is a problem that has a
simple solution:
busybox without MMU can only have HUSH as SH, so if you keep using the
default BR2_PACKAGE_BUSYBOX_CONFIG that is "package/busybox/busybox-minimal.config" it will automatically choose HUSH but with very few utilities, so we won't have umask, unset and other useful utility
written for MMU processors. You can try to check which busybox utilities
are enabled at the moment by issuing:
$ make busybox-menuconfig
To solve the problem you only need to specify:
BR2_PACKAGE_BUSYBOX_CONFIG="package/busybox/busybox-minmal.config" That enables all the HUSH utilites we need to have a working NOMMU rootfs. So please add:
BR2_PACKAGE_BUSYBOX_CONFIG="package/busybox/busybox-minmal.config" right after:
# Filesystem
I wait for V5 to test.
Thank you!
Best regards
Signature · 6 lines
Giulio Benetti CEO/CTO@Benetti Engineering sas _______________________________________________ buildroot mailing list [email protected] https://lists.buildroot.org/mailman/listinfo/buildroot