Skip to contentSkip to conversation

ARM: dts: aspeed: Add device tree for Ufispace NCPLite BMC

PATCH In review Jordan Chang 2 participants 3 messages Jan 5, 2023 – Jan 19, 2023

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ARM: dts: aspeed: Add device tree for Ufispace NCPLite BMC

Add initial version of device tree for Ufispace NCPlite platform which is equipped with AST2600-based BMC.

---
 arch/arm/boot/dts/Makefile                    |   1 +
 .../boot/dts/aspeed-bmc-ufispace-ncplite.dts  | 360 ++++++++++++++++++
 2 files changed, 361 insertions(+)
 create mode 100644 arch/arm/boot/dts/aspeed-bmc-ufispace-ncplite.dts
arch/arm/boot/dts/Makefile +1 -0
index 2ee9c043218b..d26e0651e805 100644
@@ -1626,6 +1626,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-bmc-inventec-transformers.dtb \
 	aspeed-bmc-tyan-s7106.dtb \
 	aspeed-bmc-tyan-s8036.dtb \
+	aspeed-bmc-ufispace-ncplite.dtb \
 	aspeed-bmc-vegman-n110.dtb \
 	aspeed-bmc-vegman-rx20.dtb \
 	aspeed-bmc-vegman-sx20.dtb
arch/arm/boot/dts/aspeed-bmc-ufispace-ncplite.dts new file +360 -0

360 lines not on this page · raw message

Signature · 14 lines
2.39.0


-- 
******************************
This e-mail is confidential. If you are not 
the intended recipient, you must not disclose, distribute or use the 
information in it as this could be a breach of confidentiality.If you have 
received this message in error, please advise us immediately by return 
e-mail and delete the document. The address from which this message has 
been sent is strictly for business mail only and the company reserves the 
right to monitor the contents of communications and take action where and 
when it is deemed necessary.
Thank you for your co-operation.
maintainer
#1 lore raw

Hello Jordan,

Quoted 5 lines · Jordan Chang

Add initial version of device tree for Ufispace NCPlite platform which is equipped with AST2600-based BMC.

There's a few things that need fixing with your patch:

ERROR: code indent should use tabs where possible

WARNING: please, no spaces at the start of a line

WARNING: DT compatible string "ufispace,ncplite-bmc" appears un-documented -- check ./Documentation/devicetree/bindings/ #46: FILE: arch/arm/boot/dts/aspeed-bmc-ufispace-ncplite.dts:11:
+ compatible = "ufispace,ncplite-bmc", "aspeed,ast2600";

WARNING: DT compatible string vendor "ufispace" appears un-documented -- check ./Documentation/devicetree/bindings/vendor-prefixes.yaml #46: FILE: arch/arm/boot/dts/aspeed-bmc-ufispace-ncplite.dts:11:
+ compatible = "ufispace,ncplite-bmc", "aspeed,ast2600";

Ignore the warning about 100 columns for the gpio description, that can be left as it is. You can also ignore the warning about MAINTAINERS, this file is covered by an existing maintainers rule.

Please fix these issues and re-run scripts/checkpatch.pl. When you resubmit, send to the upstream lists (linux-arm-kernel) and I will merge into the aspeed tree, as well as backport to openbmc.

Cheers,

Joel

Quoted 399 lines
---
 arch/arm/boot/dts/Makefile                    |   1 +
 .../boot/dts/aspeed-bmc-ufispace-ncplite.dts  | 360 ++++++++++++++++++
 2 files changed, 361 insertions(+)
 create mode 100644 arch/arm/boot/dts/aspeed-bmc-ufispace-ncplite.dts
arch/arm/boot/dts/Makefile +1 -0
index 2ee9c043218b..d26e0651e805 100644
@@ -1626,6 +1626,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
        aspeed-bmc-inventec-transformers.dtb \
        aspeed-bmc-tyan-s7106.dtb \
        aspeed-bmc-tyan-s8036.dtb \
+       aspeed-bmc-ufispace-ncplite.dtb \
        aspeed-bmc-vegman-n110.dtb \
        aspeed-bmc-vegman-rx20.dtb \
        aspeed-bmc-vegman-sx20.dtb
arch/arm/boot/dts/aspeed-bmc-ufispace-ncplite.dts new file +360 -1
new file mode 100644
index 000000000000..43e5d8901b04
@@ -0,0 +1,360 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright (c) 2022 Ufispace Co., Ltd.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+       model = "Ufispace NCPLite BMC";
+       compatible = "ufispace,ncplite-bmc", "aspeed,ast2600";
+
+       aliases {
+               serial4 = &uart5;
+       };
+
+       chosen {
+               stdout-path = &uart5;
+               bootargs = "console=ttyS4,115200n8 earlycon";
+       };
+
+       memory@80000000 {
+               device_type = "memory";
+               reg = <0x80000000 0x80000000>;
+       };
+
+       iio-hwmon {
+               compatible = "iio-hwmon";
+               io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+                              <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+                              <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
+                              <&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
+       };
+
+       gpio-keys {
+               compatible = "gpio-keys";
+
+               fan-status-int-l {
+                        label = "fan-status-int-l";
+                        gpios = <&gpio0 ASPEED_GPIO(M, 2) GPIO_ACTIVE_LOW>;
+                        linux,code = <ASPEED_GPIO(M, 2)>;
+                };
+
+                allpwr-good {
+                        label = "allpwr-good";
+                        gpios = <&gpio0 ASPEED_GPIO(V, 4) GPIO_ACTIVE_HIGH>;
+                        linux,code = <ASPEED_GPIO(V, 4)>;
+                };
+
+                psu0-alert-n {
+                        label = "psu0-alert-n";
+                        gpios = <&gpio0 ASPEED_GPIO(V, 1) GPIO_ACTIVE_LOW>;
+                        linux,code = <ASPEED_GPIO(V, 1)>;
+                };
+
+                psu1-alert-n {
+                        label = "psu1-alert-n";
+                        gpios = <&gpio0 ASPEED_GPIO(V, 2) GPIO_ACTIVE_LOW>;
+                        linux,code = <ASPEED_GPIO(V, 2)>;
+                };
+
+                int-thermal-alert {
+                        label = "int-thermal-alert";
+                        gpios = <&gpio0 ASPEED_GPIO(P, 2) GPIO_ACTIVE_LOW>;
+                        linux,code = <ASPEED_GPIO(P, 2)>;
+                };
+
+                cpu-caterr-l {
+                        label = "cpu-caterr-l";
+                        gpios = <&gpio0 ASPEED_GPIO(N, 3) GPIO_ACTIVE_LOW>;
+                        linux,code = <ASPEED_GPIO(N, 3)>;
+                };
+
+                cpu-thermtrip-l {
+                        label = "cpu-thermtrip-l";
+                        gpios = <&gpio0 ASPEED_GPIO(V, 5) GPIO_ACTIVE_LOW>;
+                        linux,code = <ASPEED_GPIO(V, 5)>;
+                };
+
+                psu0-presence-l {
+                        label = "psu0-presence-l";
+                        gpios = <&gpio0 ASPEED_GPIO(F, 6) GPIO_ACTIVE_LOW>;
+                        linux,code = <ASPEED_GPIO(F, 6)>;
+                };
+
+                psu1-presence-l {
+                        label = "psu1-presence-l";
+                        gpios = <&gpio0 ASPEED_GPIO(F, 7) GPIO_ACTIVE_LOW>;
+                        linux,code = <ASPEED_GPIO(F, 7)>;
+                };
+
+                psu0-power-ok {
+                        label = "psu0-power-ok";
+                        gpios = <&gpio0 ASPEED_GPIO(M, 4) GPIO_ACTIVE_HIGH>;
+                        linux,code = <ASPEED_GPIO(M, 4)>;
+                };
+
+                psu1-power-ok {
+                        label = "psu1-power-ok";
+                        gpios = <&gpio0 ASPEED_GPIO(M, 5) GPIO_ACTIVE_HIGH>;
+                        linux,code = <ASPEED_GPIO(M, 5)>;
+                };
+       };
+
+       gpio-keys-polled {
+               compatible = "gpio-keys-polled";
+               #address-cells = <1>;
+               #size-cells = <0>;
+               poll-interval = <1000>;
+
+               fan0-presence {
+                       label = "fan0-presence";
+                       gpios = <&fan_ioexp 2 GPIO_ACTIVE_LOW>;
+                       linux,code = <2>;
+               };
+
+               fan1-presence {
+                       label = "fan1-presence";
+                       gpios = <&fan_ioexp 6 GPIO_ACTIVE_LOW>;
+                       linux,code = <6>;
+               };
+
+               fan2-presence {
+                       label = "fan2-presence";
+                       gpios = <&fan_ioexp 10 GPIO_ACTIVE_LOW>;
+                       linux,code = <10>;
+               };
+
+               fan3-presence {
+                       label = "fan3-presence";
+                       gpios = <&fan_ioexp 14 GPIO_ACTIVE_LOW>;
+                       linux,code = <14>;
+               };
+       };
+};
+
+&mac2 {
+       status = "okay";
+       use-ncsi;
+
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_rmii3_default>;
+       clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>,
+                <&syscon ASPEED_CLK_MAC3RCLK>;
+       clock-names = "MACCLK", "RCLK";
+};
+
+&fmc {
+       status = "okay";
+       flash@0 {
+               status = "okay";
+               m25p,fast-read;
+               label = "bmc";
+               spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+       };
+
+       flash@1 {
+               status = "okay";
+               m25p,fast-read;
+               label = "alt-bmc";
+               spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64-alt.dtsi"
+       };
+};
+
+&uart1 {
+       status = "okay";
+};
+
+&uart4 {
+       status = "okay";
+};
+
+&uart5 {
+       status = "okay";
+};
+
+&kcs3 {
+        status = "okay";
+        aspeed,lpc-io-reg = <0xca2>;
+};
+
+&lpc_reset {
+       status = "okay";
+};
+
+&lpc_ctrl {
+       status = "okay";
+};
+
+&uart_routing {
+       status = "okay";
+};
+
+&wdt1 {
+       status = "okay";
+};
+
+&wdt2 {
+       status = "okay";
+};
+
+&peci0 {
+       status = "okay";
+};
+
+&udc {
+        status = "okay";
+};
+
+&adc0 {
+        vref = <2500>;
+        status = "okay";
+
+        pinctrl-names = "default";
+        pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+                &pinctrl_adc2_default &pinctrl_adc3_default
+                &pinctrl_adc4_default &pinctrl_adc5_default
+                &pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+        vref = <2500>;
+        status = "okay";
+
+        pinctrl-names = "default";
+        pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+                &pinctrl_adc10_default &pinctrl_adc11_default
+                &pinctrl_adc12_default &pinctrl_adc13_default
+                &pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&i2c0 {
+       status = "okay";
+};
+
+&i2c1 {
+       status = "okay";
+
+        lm75@48 {
+                compatible = "national,lm75";
+                reg = <0x48>;
+        };
+
+        lm75@49 {
+                compatible = "national,lm75";
+                reg = <0x49>;
+        };
+
+        lm86@4c {
+                compatible = "national,lm86";
+                reg = <0x4c>;
+        };
+};
+
+&i2c2 {
+       status = "okay";
+
+       lm75@4f {
+               cpmpatible = "national,lm75";
+               reg = <0x4f>;
+       };
+
+        fan_ioexp: pca9535@20 {
+                compatible = "nxp,pca9535";
+                reg = <0x20>;
+               #address-cells = <1>;
+                #size-cells = <0>;
+               gpio-controller;
+               #gpio-cells = <2>;
+
+               gpio-line-names =
+               "","","presence-fan0","",
+               "","","presence-fan1","",
+               "","","presence-fan2","",
+               "","","presence-fan3","";
+        };
+};
+
+&i2c3 {
+       status = "okay";
+
+        eeprom@50 {
+                compatible = "atmel,24c128";
+                reg = <0x50>;
+                pagesize = <64>;
+        };
+};
+
+&i2c4 {
+       status = "okay";
+
+       psu@58 {
+                compatible = "pmbus";
+                reg = <0x58>;
+        };
+
+        eeprom@50 {
+                compatible = "atmel,24c02";
+                reg = <0x50>;
+                pagesize = <1>;
+        };
+};
+
+&i2c5 {
+       status = "okay";
+
+       psu@58 {
+                compatible = "pmbus";
+                reg = <0x58>;
+        };
+
+        eeprom@50 {
+                compatible = "atmel,24c02";
+                reg = <0x50>;
+                pagesize = <1>;
+        };
+};
+
+&i2c8 {
+       status = "okay";
+};
+
+&i2c10 {
+       status = "okay";
+
+       lm75@4d {
+               compatible = "national,lm75";
+                reg = <0x4d>;
+       };
+};
+
+&gpio0 {
+       status = "okay";
+
+       gpio-line-names =
+       /*A0-A7*/       "","","","","","","","",
+       /*B0-B7*/       "","","","","","","","",
+       /*C0-C7*/       "","","","","","","","",
+       /*D0-D7*/       "","","","","","","","",
+       /*E0-E7*/       "","","","","","","","",
+       /*F0-F7*/       "CPU_PWRGD","","","power-button","host0-ready","","presence-ps0","presence-ps1",
+       /*G0-G7*/       "","","","","","","","",
+       /*H0-H7*/       "","","","","","","","",
+       /*I0-I7*/       "","","","","","reset-button","","",
+       /*J0-J7*/       "","","","","","","","",
+       /*K0-K7*/       "","","","","","","","",
+       /*L0-L7*/       "","","","","","","","",
+       /*M0-M7*/       "","","","","","","","",
+       /*N0-N7*/       "power-chassis-control0","power-chassis-control1","","","","","","",
+       /*O0-O7*/       "","","","","","","","",
+       /*P0-P7*/       "","","","","","","","",
+       /*Q0-Q7*/       "","","","","","","","",
+       /*R0-R7*/       "","","","","","","","",
+       /*S0-S7*/       "","","","","","","","",
+       /*T0-T7*/       "","","","","","","","",
+       /*U0-U7*/       "","","","","","","","",
+       /*V0-V7*/       "","","","","power-chassis-good","","","";
+};
--

2.39.0

--
******************************
This e-mail is confidential. If you are not
the intended recipient, you must not disclose, distribute or use the information in it as this could be a breach of confidentiality.If you have received this message in error, please advise us immediately by return e-mail and delete the document. The address from which this message has been sent is strictly for business mail only and the company reserves the right to monitor the contents of communications and take action where and when it is deemed necessary.
Thank you for your co-operation.

#2 lore raw

Hello Joel,

Thanks for your comments.

Quoted 26 lines · Joel Stanley

Hello Jordan,

Quoted 5 lines · Jordan Chang

Add initial version of device tree for Ufispace NCPlite platform which is equipped with AST2600-based BMC.

There's a few things that need fixing with your patch:

ERROR: code indent should use tabs where possible

WARNING: please, no spaces at the start of a line

WARNING: DT compatible string "ufispace,ncplite-bmc" appears un-documented -- check ./Documentation/devicetree/bindings/ #46: FILE: arch/arm/boot/dts/aspeed-bmc-ufispace-ncplite.dts:11:
+ compatible = "ufispace,ncplite-bmc", "aspeed,ast2600";

WARNING: DT compatible string vendor "ufispace" appears un-documented -- check ./Documentation/devicetree/bindings/vendor-prefixes.yaml #46: FILE: arch/arm/boot/dts/aspeed-bmc-ufispace-ncplite.dts:11:
+ compatible = "ufispace,ncplite-bmc", "aspeed,ast2600";

Quoted 8 lines

Ignore the warning about 100 columns for the gpio description, that can be left as it is. You can also ignore the warning about MAINTAINERS, this file is covered by an existing maintainers rule.

Please fix these issues and re-run scripts/checkpatch.pl. When you resubmit, send to the upstream lists (linux-arm-kernel) and I will merge into the aspeed tree, as well as backport to openbmc.

I have fixed those errors and warning issues. and check with scripts/checkpatch.pl.
Please help to check the patches on upstream lists. Thank you!

Cheers,

Jordan

Quoted 403 lines

Cheers,

Joel

Quoted 399 lines
---
 arch/arm/boot/dts/Makefile                    |   1 +
 .../boot/dts/aspeed-bmc-ufispace-ncplite.dts  | 360 ++++++++++++++++++
 2 files changed, 361 insertions(+)
 create mode 100644 arch/arm/boot/dts/aspeed-bmc-ufispace-ncplite.dts
arch/arm/boot/dts/Makefile +1 -0
index 2ee9c043218b..d26e0651e805 100644
@@ -1626,6 +1626,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
        aspeed-bmc-inventec-transformers.dtb \
        aspeed-bmc-tyan-s7106.dtb \
        aspeed-bmc-tyan-s8036.dtb \
+       aspeed-bmc-ufispace-ncplite.dtb \
        aspeed-bmc-vegman-n110.dtb \
        aspeed-bmc-vegman-rx20.dtb \
        aspeed-bmc-vegman-sx20.dtb
arch/arm/boot/dts/aspeed-bmc-ufispace-ncplite.dts new file +360 -1
new file mode 100644
index 000000000000..43e5d8901b04
@@ -0,0 +1,360 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright (c) 2022 Ufispace Co., Ltd.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+       model = "Ufispace NCPLite BMC";
+       compatible = "ufispace,ncplite-bmc", "aspeed,ast2600";
+
+       aliases {
+               serial4 = &uart5;
+       };
+
+       chosen {
+               stdout-path = &uart5;
+               bootargs = "console=ttyS4,115200n8 earlycon";
+       };
+
+       memory@80000000 {
+               device_type = "memory";
+               reg = <0x80000000 0x80000000>;
+       };
+
+       iio-hwmon {
+               compatible = "iio-hwmon";
+               io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+                              <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+                              <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
+                              <&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
+       };
+
+       gpio-keys {
+               compatible = "gpio-keys";
+
+               fan-status-int-l {
+                        label = "fan-status-int-l";
+                        gpios = <&gpio0 ASPEED_GPIO(M, 2) GPIO_ACTIVE_LOW>;
+                        linux,code = <ASPEED_GPIO(M, 2)>;
+                };
+
+                allpwr-good {
+                        label = "allpwr-good";
+                        gpios = <&gpio0 ASPEED_GPIO(V, 4) GPIO_ACTIVE_HIGH>;
+                        linux,code = <ASPEED_GPIO(V, 4)>;
+                };
+
+                psu0-alert-n {
+                        label = "psu0-alert-n";
+                        gpios = <&gpio0 ASPEED_GPIO(V, 1) GPIO_ACTIVE_LOW>;
+                        linux,code = <ASPEED_GPIO(V, 1)>;
+                };
+
+                psu1-alert-n {
+                        label = "psu1-alert-n";
+                        gpios = <&gpio0 ASPEED_GPIO(V, 2) GPIO_ACTIVE_LOW>;
+                        linux,code = <ASPEED_GPIO(V, 2)>;
+                };
+
+                int-thermal-alert {
+                        label = "int-thermal-alert";
+                        gpios = <&gpio0 ASPEED_GPIO(P, 2) GPIO_ACTIVE_LOW>;
+                        linux,code = <ASPEED_GPIO(P, 2)>;
+                };
+
+                cpu-caterr-l {
+                        label = "cpu-caterr-l";
+                        gpios = <&gpio0 ASPEED_GPIO(N, 3) GPIO_ACTIVE_LOW>;
+                        linux,code = <ASPEED_GPIO(N, 3)>;
+                };
+
+                cpu-thermtrip-l {
+                        label = "cpu-thermtrip-l";
+                        gpios = <&gpio0 ASPEED_GPIO(V, 5) GPIO_ACTIVE_LOW>;
+                        linux,code = <ASPEED_GPIO(V, 5)>;
+                };
+
+                psu0-presence-l {
+                        label = "psu0-presence-l";
+                        gpios = <&gpio0 ASPEED_GPIO(F, 6) GPIO_ACTIVE_LOW>;
+                        linux,code = <ASPEED_GPIO(F, 6)>;
+                };
+
+                psu1-presence-l {
+                        label = "psu1-presence-l";
+                        gpios = <&gpio0 ASPEED_GPIO(F, 7) GPIO_ACTIVE_LOW>;
+                        linux,code = <ASPEED_GPIO(F, 7)>;
+                };
+
+                psu0-power-ok {
+                        label = "psu0-power-ok";
+                        gpios = <&gpio0 ASPEED_GPIO(M, 4) GPIO_ACTIVE_HIGH>;
+                        linux,code = <ASPEED_GPIO(M, 4)>;
+                };
+
+                psu1-power-ok {
+                        label = "psu1-power-ok";
+                        gpios = <&gpio0 ASPEED_GPIO(M, 5) GPIO_ACTIVE_HIGH>;
+                        linux,code = <ASPEED_GPIO(M, 5)>;
+                };
+       };
+
+       gpio-keys-polled {
+               compatible = "gpio-keys-polled";
+               #address-cells = <1>;
+               #size-cells = <0>;
+               poll-interval = <1000>;
+
+               fan0-presence {
+                       label = "fan0-presence";
+                       gpios = <&fan_ioexp 2 GPIO_ACTIVE_LOW>;
+                       linux,code = <2>;
+               };
+
+               fan1-presence {
+                       label = "fan1-presence";
+                       gpios = <&fan_ioexp 6 GPIO_ACTIVE_LOW>;
+                       linux,code = <6>;
+               };
+
+               fan2-presence {
+                       label = "fan2-presence";
+                       gpios = <&fan_ioexp 10 GPIO_ACTIVE_LOW>;
+                       linux,code = <10>;
+               };
+
+               fan3-presence {
+                       label = "fan3-presence";
+                       gpios = <&fan_ioexp 14 GPIO_ACTIVE_LOW>;
+                       linux,code = <14>;
+               };
+       };
+};
+
+&mac2 {
+       status = "okay";
+       use-ncsi;
+
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_rmii3_default>;
+       clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>,
+                <&syscon ASPEED_CLK_MAC3RCLK>;
+       clock-names = "MACCLK", "RCLK";
+};
+
+&fmc {
+       status = "okay";
+       flash@0 {
+               status = "okay";
+               m25p,fast-read;
+               label = "bmc";
+               spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+       };
+
+       flash@1 {
+               status = "okay";
+               m25p,fast-read;
+               label = "alt-bmc";
+               spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64-alt.dtsi"
+       };
+};
+
+&uart1 {
+       status = "okay";
+};
+
+&uart4 {
+       status = "okay";
+};
+
+&uart5 {
+       status = "okay";
+};
+
+&kcs3 {
+        status = "okay";
+        aspeed,lpc-io-reg = <0xca2>;
+};
+
+&lpc_reset {
+       status = "okay";
+};
+
+&lpc_ctrl {
+       status = "okay";
+};
+
+&uart_routing {
+       status = "okay";
+};
+
+&wdt1 {
+       status = "okay";
+};
+
+&wdt2 {
+       status = "okay";
+};
+
+&peci0 {
+       status = "okay";
+};
+
+&udc {
+        status = "okay";
+};
+
+&adc0 {
+        vref = <2500>;
+        status = "okay";
+
+        pinctrl-names = "default";
+        pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+                &pinctrl_adc2_default &pinctrl_adc3_default
+                &pinctrl_adc4_default &pinctrl_adc5_default
+                &pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+        vref = <2500>;
+        status = "okay";
+
+        pinctrl-names = "default";
+        pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+                &pinctrl_adc10_default &pinctrl_adc11_default
+                &pinctrl_adc12_default &pinctrl_adc13_default
+                &pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&i2c0 {
+       status = "okay";
+};
+
+&i2c1 {
+       status = "okay";
+
+        lm75@48 {
+                compatible = "national,lm75";
+                reg = <0x48>;
+        };
+
+        lm75@49 {
+                compatible = "national,lm75";
+                reg = <0x49>;
+        };
+
+        lm86@4c {
+                compatible = "national,lm86";
+                reg = <0x4c>;
+        };
+};
+
+&i2c2 {
+       status = "okay";
+
+       lm75@4f {
+               cpmpatible = "national,lm75";
+               reg = <0x4f>;
+       };
+
+        fan_ioexp: pca9535@20 {
+                compatible = "nxp,pca9535";
+                reg = <0x20>;
+               #address-cells = <1>;
+                #size-cells = <0>;
+               gpio-controller;
+               #gpio-cells = <2>;
+
+               gpio-line-names =
+               "","","presence-fan0","",
+               "","","presence-fan1","",
+               "","","presence-fan2","",
+               "","","presence-fan3","";
+        };
+};
+
+&i2c3 {
+       status = "okay";
+
+        eeprom@50 {
+                compatible = "atmel,24c128";
+                reg = <0x50>;
+                pagesize = <64>;
+        };
+};
+
+&i2c4 {
+       status = "okay";
+
+       psu@58 {
+                compatible = "pmbus";
+                reg = <0x58>;
+        };
+
+        eeprom@50 {
+                compatible = "atmel,24c02";
+                reg = <0x50>;
+                pagesize = <1>;
+        };
+};
+
+&i2c5 {
+       status = "okay";
+
+       psu@58 {
+                compatible = "pmbus";
+                reg = <0x58>;
+        };
+
+        eeprom@50 {
+                compatible = "atmel,24c02";
+                reg = <0x50>;
+                pagesize = <1>;
+        };
+};
+
+&i2c8 {
+       status = "okay";
+};
+
+&i2c10 {
+       status = "okay";
+
+       lm75@4d {
+               compatible = "national,lm75";
+                reg = <0x4d>;
+       };
+};
+
+&gpio0 {
+       status = "okay";
+
+       gpio-line-names =
+       /*A0-A7*/       "","","","","","","","",
+       /*B0-B7*/       "","","","","","","","",
+       /*C0-C7*/       "","","","","","","","",
+       /*D0-D7*/       "","","","","","","","",
+       /*E0-E7*/       "","","","","","","","",
+       /*F0-F7*/       "CPU_PWRGD","","","power-button","host0-ready","","presence-ps0","presence-ps1",
+       /*G0-G7*/       "","","","","","","","",
+       /*H0-H7*/       "","","","","","","","",
+       /*I0-I7*/       "","","","","","reset-button","","",
+       /*J0-J7*/       "","","","","","","","",
+       /*K0-K7*/       "","","","","","","","",
+       /*L0-L7*/       "","","","","","","","",
+       /*M0-M7*/       "","","","","","","","",
+       /*N0-N7*/       "power-chassis-control0","power-chassis-control1","","","","","","",
+       /*O0-O7*/       "","","","","","","","",
+       /*P0-P7*/       "","","","","","","","",
+       /*Q0-Q7*/       "","","","","","","","",
+       /*R0-R7*/       "","","","","","","","",
+       /*S0-S7*/       "","","","","","","","",
+       /*T0-T7*/       "","","","","","","","",
+       /*U0-U7*/       "","","","","","","","",
+       /*V0-V7*/       "","","","","power-chassis-good","","","";
+};
--

2.39.0

--
******************************
This e-mail is confidential. If you are not
the intended recipient, you must not disclose, distribute or use the information in it as this could be a breach of confidentiality.If you have received this message in error, please advise us immediately by return e-mail and delete the document. The address from which this message has been sent is strictly for business mail only and the company reserves the right to monitor the contents of communications and take action where and when it is deemed necessary.
Thank you for your co-operation.

Signature · 10 lines
******************************
This e-mail is confidential. If you are not 
the intended recipient, you must not disclose, distribute or use the 
information in it as this could be a breach of confidentiality.If you have 
received this message in error, please advise us immediately by return 
e-mail and delete the document. The address from which this message has 
been sent is strictly for business mail only and the company reserves the 
right to monitor the contents of communications and take action where and 
when it is deemed necessary.
Thank you for your co-operation.