ARM: dts: aspeed: Add device tree for Ufispace NCPLite BMC
Subsystems (3)
PATCH 1/1 ARM: dts: aspeed: Add device tree for Ufispace NCPLite BMC
Add initial version of device tree for Ufispace NCPlite platform which is equipped with AST2600-based BMC.
--- arch/arm/boot/dts/Makefile | 1 + .../boot/dts/aspeed-bmc-ufispace-ncplite.dts | 360 ++++++++++++++++++ 2 files changed, 361 insertions(+) create mode 100644 arch/arm/boot/dts/aspeed-bmc-ufispace-ncplite.dts
arch/arm/boot/dts/Makefile +1 -0
@@ -1626,6 +1626,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \ aspeed-bmc-inventec-transformers.dtb \ aspeed-bmc-tyan-s7106.dtb \ aspeed-bmc-tyan-s8036.dtb \ + aspeed-bmc-ufispace-ncplite.dtb \ aspeed-bmc-vegman-n110.dtb \ aspeed-bmc-vegman-rx20.dtb \ aspeed-bmc-vegman-sx20.dtb
arch/arm/boot/dts/aspeed-bmc-ufispace-ncplite.dts new file +360 -0
360 lines not on this page · raw message
Signature · 14 lines
2.39.0 -- ****************************** This e-mail is confidential. If you are not the intended recipient, you must not disclose, distribute or use the information in it as this could be a breach of confidentiality.If you have received this message in error, please advise us immediately by return e-mail and delete the document. The address from which this message has been sent is strictly for business mail only and the company reserves the right to monitor the contents of communications and take action where and when it is deemed necessary. Thank you for your co-operation.
Joel Stanley
maintainerHello Jordan,
Quoted 5 lines · Jordan Chang
Add initial version of device tree for Ufispace NCPlite platform which is equipped with AST2600-based BMC.
Signed-off-by Jordan Chang <[email protected]>
There's a few things that need fixing with your patch:
ERROR: code indent should use tabs where possible
WARNING: please, no spaces at the start of a line
WARNING: DT compatible string "ufispace,ncplite-bmc" appears un-documented -- check ./Documentation/devicetree/bindings/ #46: FILE: arch/arm/boot/dts/aspeed-bmc-ufispace-ncplite.dts:11:
+ compatible = "ufispace,ncplite-bmc", "aspeed,ast2600";
WARNING: DT compatible string vendor "ufispace" appears un-documented -- check ./Documentation/devicetree/bindings/vendor-prefixes.yaml #46: FILE: arch/arm/boot/dts/aspeed-bmc-ufispace-ncplite.dts:11:
+ compatible = "ufispace,ncplite-bmc", "aspeed,ast2600";
Ignore the warning about 100 columns for the gpio description, that can be left as it is. You can also ignore the warning about MAINTAINERS, this file is covered by an existing maintainers rule.
Please fix these issues and re-run scripts/checkpatch.pl. When you resubmit, send to the upstream lists (linux-arm-kernel) and I will merge into the aspeed tree, as well as backport to openbmc.
Cheers,
Joel
Quoted 399 lines
--- arch/arm/boot/dts/Makefile | 1 + .../boot/dts/aspeed-bmc-ufispace-ncplite.dts | 360 ++++++++++++++++++ 2 files changed, 361 insertions(+) create mode 100644 arch/arm/boot/dts/aspeed-bmc-ufispace-ncplite.dtsarch/arm/boot/dts/Makefile +1
-0@@ -1626,6 +1626,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \ aspeed-bmc-inventec-transformers.dtb \ aspeed-bmc-tyan-s7106.dtb \ aspeed-bmc-tyan-s8036.dtb \ + aspeed-bmc-ufispace-ncplite.dtb \ aspeed-bmc-vegman-n110.dtb \ aspeed-bmc-vegman-rx20.dtb \ aspeed-bmc-vegman-sx20.dtbarch/arm/boot/dts/aspeed-bmc-ufispace-ncplite.dts new file +360
-1@@ -0,0 +1,360 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +// Copyright (c) 2022 Ufispace Co., Ltd. +/dts-v1/; + +#include "aspeed-g6.dtsi" +#include <dt-bindings/i2c/i2c.h> +#include <dt-bindings/gpio/aspeed-gpio.h> + +/ { + model = "Ufispace NCPLite BMC"; + compatible = "ufispace,ncplite-bmc", "aspeed,ast2600"; + + aliases { + serial4 = &uart5; + }; + + chosen { + stdout-path = &uart5; + bootargs = "console=ttyS4,115200n8 earlycon"; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0x80000000>; + }; + + iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>, + <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>, + <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>, + <&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>; + }; + + gpio-keys { + compatible = "gpio-keys"; + + fan-status-int-l { + label = "fan-status-int-l"; + gpios = <&gpio0 ASPEED_GPIO(M, 2) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(M, 2)>; + }; + + allpwr-good { + label = "allpwr-good"; + gpios = <&gpio0 ASPEED_GPIO(V, 4) GPIO_ACTIVE_HIGH>; + linux,code = <ASPEED_GPIO(V, 4)>; + }; + + psu0-alert-n { + label = "psu0-alert-n"; + gpios = <&gpio0 ASPEED_GPIO(V, 1) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(V, 1)>; + }; + + psu1-alert-n { + label = "psu1-alert-n"; + gpios = <&gpio0 ASPEED_GPIO(V, 2) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(V, 2)>; + }; + + int-thermal-alert { + label = "int-thermal-alert"; + gpios = <&gpio0 ASPEED_GPIO(P, 2) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(P, 2)>; + }; + + cpu-caterr-l { + label = "cpu-caterr-l"; + gpios = <&gpio0 ASPEED_GPIO(N, 3) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(N, 3)>; + }; + + cpu-thermtrip-l { + label = "cpu-thermtrip-l"; + gpios = <&gpio0 ASPEED_GPIO(V, 5) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(V, 5)>; + }; + + psu0-presence-l { + label = "psu0-presence-l"; + gpios = <&gpio0 ASPEED_GPIO(F, 6) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(F, 6)>; + }; + + psu1-presence-l { + label = "psu1-presence-l"; + gpios = <&gpio0 ASPEED_GPIO(F, 7) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(F, 7)>; + }; + + psu0-power-ok { + label = "psu0-power-ok"; + gpios = <&gpio0 ASPEED_GPIO(M, 4) GPIO_ACTIVE_HIGH>; + linux,code = <ASPEED_GPIO(M, 4)>; + }; + + psu1-power-ok { + label = "psu1-power-ok"; + gpios = <&gpio0 ASPEED_GPIO(M, 5) GPIO_ACTIVE_HIGH>; + linux,code = <ASPEED_GPIO(M, 5)>; + }; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <1000>; + + fan0-presence { + label = "fan0-presence"; + gpios = <&fan_ioexp 2 GPIO_ACTIVE_LOW>; + linux,code = <2>; + }; + + fan1-presence { + label = "fan1-presence"; + gpios = <&fan_ioexp 6 GPIO_ACTIVE_LOW>; + linux,code = <6>; + }; + + fan2-presence { + label = "fan2-presence"; + gpios = <&fan_ioexp 10 GPIO_ACTIVE_LOW>; + linux,code = <10>; + }; + + fan3-presence { + label = "fan3-presence"; + gpios = <&fan_ioexp 14 GPIO_ACTIVE_LOW>; + linux,code = <14>; + }; + }; +}; + +&mac2 { + status = "okay"; + use-ncsi; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rmii3_default>; + clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>, + <&syscon ASPEED_CLK_MAC3RCLK>; + clock-names = "MACCLK", "RCLK"; +}; + +&fmc { + status = "okay"; + flash@0 { + status = "okay"; + m25p,fast-read; + label = "bmc"; + spi-max-frequency = <50000000>; +#include "openbmc-flash-layout-64.dtsi" + }; + + flash@1 { + status = "okay"; + m25p,fast-read; + label = "alt-bmc"; + spi-max-frequency = <50000000>; +#include "openbmc-flash-layout-64-alt.dtsi" + }; +}; + +&uart1 { + status = "okay"; +}; + +&uart4 { + status = "okay"; +}; + +&uart5 { + status = "okay"; +}; + +&kcs3 { + status = "okay"; + aspeed,lpc-io-reg = <0xca2>; +}; + +&lpc_reset { + status = "okay"; +}; + +&lpc_ctrl { + status = "okay"; +}; + +&uart_routing { + status = "okay"; +}; + +&wdt1 { + status = "okay"; +}; + +&wdt2 { + status = "okay"; +}; + +&peci0 { + status = "okay"; +}; + +&udc { + status = "okay"; +}; + +&adc0 { + vref = <2500>; + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default + &pinctrl_adc2_default &pinctrl_adc3_default + &pinctrl_adc4_default &pinctrl_adc5_default + &pinctrl_adc6_default &pinctrl_adc7_default>; +}; + +&adc1 { + vref = <2500>; + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default + &pinctrl_adc10_default &pinctrl_adc11_default + &pinctrl_adc12_default &pinctrl_adc13_default + &pinctrl_adc14_default &pinctrl_adc15_default>; +}; + +&i2c0 { + status = "okay"; +}; + +&i2c1 { + status = "okay"; + + lm75@48 { + compatible = "national,lm75"; + reg = <0x48>; + }; + + lm75@49 { + compatible = "national,lm75"; + reg = <0x49>; + }; + + lm86@4c { + compatible = "national,lm86"; + reg = <0x4c>; + }; +}; + +&i2c2 { + status = "okay"; + + lm75@4f { + cpmpatible = "national,lm75"; + reg = <0x4f>; + }; + + fan_ioexp: pca9535@20 { + compatible = "nxp,pca9535"; + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + gpio-controller; + #gpio-cells = <2>; + + gpio-line-names = + "","","presence-fan0","", + "","","presence-fan1","", + "","","presence-fan2","", + "","","presence-fan3",""; + }; +}; + +&i2c3 { + status = "okay"; + + eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + pagesize = <64>; + }; +}; + +&i2c4 { + status = "okay"; + + psu@58 { + compatible = "pmbus"; + reg = <0x58>; + }; + + eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + pagesize = <1>; + }; +}; + +&i2c5 { + status = "okay"; + + psu@58 { + compatible = "pmbus"; + reg = <0x58>; + }; + + eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + pagesize = <1>; + }; +}; + +&i2c8 { + status = "okay"; +}; + +&i2c10 { + status = "okay"; + + lm75@4d { + compatible = "national,lm75"; + reg = <0x4d>; + }; +}; + +&gpio0 { + status = "okay"; + + gpio-line-names = + /*A0-A7*/ "","","","","","","","", + /*B0-B7*/ "","","","","","","","", + /*C0-C7*/ "","","","","","","","", + /*D0-D7*/ "","","","","","","","", + /*E0-E7*/ "","","","","","","","", + /*F0-F7*/ "CPU_PWRGD","","","power-button","host0-ready","","presence-ps0","presence-ps1", + /*G0-G7*/ "","","","","","","","", + /*H0-H7*/ "","","","","","","","", + /*I0-I7*/ "","","","","","reset-button","","", + /*J0-J7*/ "","","","","","","","", + /*K0-K7*/ "","","","","","","","", + /*L0-L7*/ "","","","","","","","", + /*M0-M7*/ "","","","","","","","", + /*N0-N7*/ "power-chassis-control0","power-chassis-control1","","","","","","", + /*O0-O7*/ "","","","","","","","", + /*P0-P7*/ "","","","","","","","", + /*Q0-Q7*/ "","","","","","","","", + /*R0-R7*/ "","","","","","","","", + /*S0-S7*/ "","","","","","","","", + /*T0-T7*/ "","","","","","","","", + /*U0-U7*/ "","","","","","","","", + /*V0-V7*/ "","","","","power-chassis-good","","",""; +}; --2.39.0
--
******************************
This e-mail is confidential. If you are not
the intended recipient, you must not disclose, distribute or use the information in it as this could be a breach of confidentiality.If you have received this message in error, please advise us immediately by return e-mail and delete the document. The address from which this message has been sent is strictly for business mail only and the company reserves the right to monitor the contents of communications and take action where and when it is deemed necessary.
Thank you for your co-operation.
Hello Joel,
Thanks for your comments.
Quoted 26 lines · Joel Stanley
Hello Jordan,
Quoted 5 lines · Jordan Chang
Add initial version of device tree for Ufispace NCPlite platform which is equipped with AST2600-based BMC.
Signed-off-by Jordan Chang <[email protected]>There's a few things that need fixing with your patch:
ERROR: code indent should use tabs where possible
WARNING: please, no spaces at the start of a line
WARNING: DT compatible string "ufispace,ncplite-bmc" appears un-documented -- check
./Documentation/devicetree/bindings/#46: FILE:arch/arm/boot/dts/aspeed-bmc-ufispace-ncplite.dts:11:
+ compatible = "ufispace,ncplite-bmc", "aspeed,ast2600";WARNING: DT compatible string vendor "ufispace" appears un-documented -- check
./Documentation/devicetree/bindings/vendor-prefixes.yaml#46: FILE:arch/arm/boot/dts/aspeed-bmc-ufispace-ncplite.dts:11:
+ compatible = "ufispace,ncplite-bmc", "aspeed,ast2600";
Quoted 8 lines
Ignore the warning about 100 columns for the gpio description, that can be left as it is. You can also ignore the warning about
MAINTAINERS, this file is covered by an existing maintainers rule.Please fix these issues and re-run
scripts/checkpatch.pl. When you resubmit, send to the upstream lists (linux-arm-kernel) and I will merge into the aspeed tree, as well as backport to openbmc.
I have fixed those errors and warning issues. and check with scripts/checkpatch.pl.
Please help to check the patches on upstream lists. Thank you!
Cheers,
Jordan
Quoted 403 lines
Cheers,
Joel
Quoted 399 lines
--- arch/arm/boot/dts/Makefile | 1 + .../boot/dts/aspeed-bmc-ufispace-ncplite.dts | 360 ++++++++++++++++++ 2 files changed, 361 insertions(+) create mode 100644 arch/arm/boot/dts/aspeed-bmc-ufispace-ncplite.dtsarch/arm/boot/dts/Makefile +1
-0@@ -1626,6 +1626,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \ aspeed-bmc-inventec-transformers.dtb \ aspeed-bmc-tyan-s7106.dtb \ aspeed-bmc-tyan-s8036.dtb \ + aspeed-bmc-ufispace-ncplite.dtb \ aspeed-bmc-vegman-n110.dtb \ aspeed-bmc-vegman-rx20.dtb \ aspeed-bmc-vegman-sx20.dtbarch/arm/boot/dts/aspeed-bmc-ufispace-ncplite.dts new file +360
-1@@ -0,0 +1,360 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +// Copyright (c) 2022 Ufispace Co., Ltd. +/dts-v1/; + +#include "aspeed-g6.dtsi" +#include <dt-bindings/i2c/i2c.h> +#include <dt-bindings/gpio/aspeed-gpio.h> + +/ { + model = "Ufispace NCPLite BMC"; + compatible = "ufispace,ncplite-bmc", "aspeed,ast2600"; + + aliases { + serial4 = &uart5; + }; + + chosen { + stdout-path = &uart5; + bootargs = "console=ttyS4,115200n8 earlycon"; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0x80000000>; + }; + + iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>, + <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>, + <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>, + <&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>; + }; + + gpio-keys { + compatible = "gpio-keys"; + + fan-status-int-l { + label = "fan-status-int-l"; + gpios = <&gpio0 ASPEED_GPIO(M, 2) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(M, 2)>; + }; + + allpwr-good { + label = "allpwr-good"; + gpios = <&gpio0 ASPEED_GPIO(V, 4) GPIO_ACTIVE_HIGH>; + linux,code = <ASPEED_GPIO(V, 4)>; + }; + + psu0-alert-n { + label = "psu0-alert-n"; + gpios = <&gpio0 ASPEED_GPIO(V, 1) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(V, 1)>; + }; + + psu1-alert-n { + label = "psu1-alert-n"; + gpios = <&gpio0 ASPEED_GPIO(V, 2) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(V, 2)>; + }; + + int-thermal-alert { + label = "int-thermal-alert"; + gpios = <&gpio0 ASPEED_GPIO(P, 2) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(P, 2)>; + }; + + cpu-caterr-l { + label = "cpu-caterr-l"; + gpios = <&gpio0 ASPEED_GPIO(N, 3) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(N, 3)>; + }; + + cpu-thermtrip-l { + label = "cpu-thermtrip-l"; + gpios = <&gpio0 ASPEED_GPIO(V, 5) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(V, 5)>; + }; + + psu0-presence-l { + label = "psu0-presence-l"; + gpios = <&gpio0 ASPEED_GPIO(F, 6) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(F, 6)>; + }; + + psu1-presence-l { + label = "psu1-presence-l"; + gpios = <&gpio0 ASPEED_GPIO(F, 7) GPIO_ACTIVE_LOW>; + linux,code = <ASPEED_GPIO(F, 7)>; + }; + + psu0-power-ok { + label = "psu0-power-ok"; + gpios = <&gpio0 ASPEED_GPIO(M, 4) GPIO_ACTIVE_HIGH>; + linux,code = <ASPEED_GPIO(M, 4)>; + }; + + psu1-power-ok { + label = "psu1-power-ok"; + gpios = <&gpio0 ASPEED_GPIO(M, 5) GPIO_ACTIVE_HIGH>; + linux,code = <ASPEED_GPIO(M, 5)>; + }; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <1000>; + + fan0-presence { + label = "fan0-presence"; + gpios = <&fan_ioexp 2 GPIO_ACTIVE_LOW>; + linux,code = <2>; + }; + + fan1-presence { + label = "fan1-presence"; + gpios = <&fan_ioexp 6 GPIO_ACTIVE_LOW>; + linux,code = <6>; + }; + + fan2-presence { + label = "fan2-presence"; + gpios = <&fan_ioexp 10 GPIO_ACTIVE_LOW>; + linux,code = <10>; + }; + + fan3-presence { + label = "fan3-presence"; + gpios = <&fan_ioexp 14 GPIO_ACTIVE_LOW>; + linux,code = <14>; + }; + }; +}; + +&mac2 { + status = "okay"; + use-ncsi; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rmii3_default>; + clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>, + <&syscon ASPEED_CLK_MAC3RCLK>; + clock-names = "MACCLK", "RCLK"; +}; + +&fmc { + status = "okay"; + flash@0 { + status = "okay"; + m25p,fast-read; + label = "bmc"; + spi-max-frequency = <50000000>; +#include "openbmc-flash-layout-64.dtsi" + }; + + flash@1 { + status = "okay"; + m25p,fast-read; + label = "alt-bmc"; + spi-max-frequency = <50000000>; +#include "openbmc-flash-layout-64-alt.dtsi" + }; +}; + +&uart1 { + status = "okay"; +}; + +&uart4 { + status = "okay"; +}; + +&uart5 { + status = "okay"; +}; + +&kcs3 { + status = "okay"; + aspeed,lpc-io-reg = <0xca2>; +}; + +&lpc_reset { + status = "okay"; +}; + +&lpc_ctrl { + status = "okay"; +}; + +&uart_routing { + status = "okay"; +}; + +&wdt1 { + status = "okay"; +}; + +&wdt2 { + status = "okay"; +}; + +&peci0 { + status = "okay"; +}; + +&udc { + status = "okay"; +}; + +&adc0 { + vref = <2500>; + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default + &pinctrl_adc2_default &pinctrl_adc3_default + &pinctrl_adc4_default &pinctrl_adc5_default + &pinctrl_adc6_default &pinctrl_adc7_default>; +}; + +&adc1 { + vref = <2500>; + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default + &pinctrl_adc10_default &pinctrl_adc11_default + &pinctrl_adc12_default &pinctrl_adc13_default + &pinctrl_adc14_default &pinctrl_adc15_default>; +}; + +&i2c0 { + status = "okay"; +}; + +&i2c1 { + status = "okay"; + + lm75@48 { + compatible = "national,lm75"; + reg = <0x48>; + }; + + lm75@49 { + compatible = "national,lm75"; + reg = <0x49>; + }; + + lm86@4c { + compatible = "national,lm86"; + reg = <0x4c>; + }; +}; + +&i2c2 { + status = "okay"; + + lm75@4f { + cpmpatible = "national,lm75"; + reg = <0x4f>; + }; + + fan_ioexp: pca9535@20 { + compatible = "nxp,pca9535"; + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + gpio-controller; + #gpio-cells = <2>; + + gpio-line-names = + "","","presence-fan0","", + "","","presence-fan1","", + "","","presence-fan2","", + "","","presence-fan3",""; + }; +}; + +&i2c3 { + status = "okay"; + + eeprom@50 { + compatible = "atmel,24c128"; + reg = <0x50>; + pagesize = <64>; + }; +}; + +&i2c4 { + status = "okay"; + + psu@58 { + compatible = "pmbus"; + reg = <0x58>; + }; + + eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + pagesize = <1>; + }; +}; + +&i2c5 { + status = "okay"; + + psu@58 { + compatible = "pmbus"; + reg = <0x58>; + }; + + eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + pagesize = <1>; + }; +}; + +&i2c8 { + status = "okay"; +}; + +&i2c10 { + status = "okay"; + + lm75@4d { + compatible = "national,lm75"; + reg = <0x4d>; + }; +}; + +&gpio0 { + status = "okay"; + + gpio-line-names = + /*A0-A7*/ "","","","","","","","", + /*B0-B7*/ "","","","","","","","", + /*C0-C7*/ "","","","","","","","", + /*D0-D7*/ "","","","","","","","", + /*E0-E7*/ "","","","","","","","", + /*F0-F7*/ "CPU_PWRGD","","","power-button","host0-ready","","presence-ps0","presence-ps1", + /*G0-G7*/ "","","","","","","","", + /*H0-H7*/ "","","","","","","","", + /*I0-I7*/ "","","","","","reset-button","","", + /*J0-J7*/ "","","","","","","","", + /*K0-K7*/ "","","","","","","","", + /*L0-L7*/ "","","","","","","","", + /*M0-M7*/ "","","","","","","","", + /*N0-N7*/ "power-chassis-control0","power-chassis-control1","","","","","","", + /*O0-O7*/ "","","","","","","","", + /*P0-P7*/ "","","","","","","","", + /*Q0-Q7*/ "","","","","","","","", + /*R0-R7*/ "","","","","","","","", + /*S0-S7*/ "","","","","","","","", + /*T0-T7*/ "","","","","","","","", + /*U0-U7*/ "","","","","","","","", + /*V0-V7*/ "","","","","power-chassis-good","","",""; +}; --2.39.0
--
******************************
This e-mail is confidential. If you are not
the intended recipient, you must not disclose, distribute or use the information in it as this could be a breach of confidentiality.If you have received this message in error, please advise us immediately by return e-mail and delete the document. The address from which this message has been sent is strictly for business mail only and the company reserves the right to monitor the contents of communications and take action where and when it is deemed necessary.
Thank you for your co-operation.
Signature · 10 lines
****************************** This e-mail is confidential. If you are not the intended recipient, you must not disclose, distribute or use the information in it as this could be a breach of confidentiality.If you have received this message in error, please advise us immediately by return e-mail and delete the document. The address from which this message has been sent is strictly for business mail only and the company reserves the right to monitor the contents of communications and take action where and when it is deemed necessary. Thank you for your co-operation.