drm/msm/mdss: enable access to hw_rev from MDSS driver
Subsystems (5)
v2 cover drm/msm/mdss: enable access to hw_rev from MDSS driver
On newer platforms mdss can read hw_rev register. On older platforms the mdss driver can not read hw_rev register (to determine the platform). Add optional 'core' clock that enables access to MDSS registers before MDP5/DPU device is bound (and enabled the core clock).
Dmitry Baryshkov (4):
dt-bindings: display/msm: add core clock to the mdss bindings drm/msm/mdss: enable optional core clock for MDP5 MDSS drm/msm/mdss: check for core clk before accessing HW_REV drm/msm/mdss: move is_mdp5 condition to msm_mdss_init
.../bindings/display/msm/qcom,mdss.yaml | 34 ++++++++++++++----- drivers/gpu/drm/msm/msm_mdss.c | 31 ++++++++++++----- 2 files changed, 48 insertions(+), 17 deletions(-)
Signature · 1 line
2.39.0
PATCH v2 1/4 dt-bindings: display/msm: add core clock to the mdss bindings
Add (optional) core clock to the mdss bindings to let the MDSS driver access harware registers before MDP driver probes.
--- .../bindings/display/msm/qcom,mdss.yaml | 34 ++++++++++++++----- 1 file changed, 26 insertions(+), 8 deletions(-)
Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml +26 -8
@@ -45,17 +45,11 @@ properties: clocks: minItems: 1 - items: - - description: Display abh clock - - description: Display axi clock - - description: Display vsync clock + maxItems: 4 clock-names: minItems: 1 - items: - - const: iface - - const: bus - - const: vsync + maxItems: 4 "#address-cells": const: 1
@@ -69,6 +63,30 @@ properties: items: - description: MDSS_CORE reset +oneOf: + - properties: + clocks: + minItems: 3 + maxItems: 4 + + clock-names: + minItems: 3 + items: + - const: iface + - const: bus + - const: vsync + - const: core + - properties: + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + minItems: 1 + items: + - const: iface + - const: core + required: - compatible - reg
Signature · 1 line
2.39.0
Re: [PATCH v2 1/4] dt-bindings: display/msm: add core clock to the mdss bindings
Quoted 13 lines · Dmitry Baryshkov
Add (optional) core clock to the mdss bindings to let the MDSS driver access harware registers before MDP driver probes.
Signed-off-by Dmitry Baryshkov <[email protected]>--- .../bindings/display/msm/qcom,mdss.yaml | 34 ++++++++++++++----- 1 file changed, 26 insertions(+), 8 deletions(-)Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml +0
-0
Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml properties: · line 50
Quoted 6 lines
Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml +0
-3@@ -45,17 +45,11 @@ properties: clocks: minItems: 1 - items: - - description: Display abh clock - - description: Display axi clock
Not related to this patch, but it is a bit surprising to see AXI clock optional.
Quoted 18 lines
Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml +3
-5- - description: Display vsync clock + maxItems: 4 clock-names: minItems: 1 - items: - - const: iface - - const: bus - - const: vsync + maxItems: 4 "#address-cells": const: 1@@ -69,6 +63,30 @@ properties: items: - description: MDSS_CORE reset +oneOf:
Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml properties: · line 76
Quoted 10 lines
Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml +10
-0+ - properties: + clocks: + minItems: 3 + maxItems: 4 + + clock-names: + minItems: 3 + items: + - const: iface + - const: bus
BTW, sc7180-mdss uses here ahb name and calls it "AHB clock from dispcc".
SM8250 won't match here either. Maybe this should be reworked to specify limits here but not the names and actual clocks? IOW, drop entire oneOf?
There were a lot, a lot of changes to MDSS/DPU bindings recently, so I am really loosing track what is done where and when.
There are also few separate patchsets from you on the lists. Could they be combined into one cleanup?
I understand that sometimes new cleanup is needed after old cleanup finished (I had the same with pinctrl), so it is not a complain.
Another problem (and this time I complain) is that several of your patchsets were sent, discussed and then without any notice applied. No message that a patchset was applied to some tree. Look:
https://lore.kernel.org/all/[email protected]/
https://lore.kernel.org/all/[email protected]/
Nothing. Silent application. If you are the maintainer which picks up the patch, please always, always send message that they are applied. Patchwork does it automatically, b4 can do it easily as well. If you use other tools - use other tools for sending it. Otherwise things are discussed on mailing lists, receive several comments and there is never a resubmit but instead they show in the tree.
Best regards,
Krzysztof
Re: [PATCH v2 1/4] dt-bindings: display/msm: add core clock to the mdss bindings
Quoted 15 lines · Krzysztof Kozlowski
Quoted 14 lines · Dmitry Baryshkov
Add (optional) core clock to the mdss bindings to let the MDSS driver access harware registers before MDP driver probes.
Signed-off-by Dmitry Baryshkov <[email protected]>--- .../bindings/display/msm/qcom,mdss.yaml | 34 ++++++++++++++----- 1 file changed, 26 insertions(+), 8 deletions(-)Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml +0
-0@@ -45,17 +45,11 @@ properties:
Quoted 8 lines
Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml properties: · line 50
Quoted 5 lines
Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml +0
-3clocks: minItems: 1 - items: - - description: Display abh clock - - description: Display axi clockNot related to this patch, but it is a bit surprising to see AXI clock optional.
Hmm, There is one defined downstream. Probably we should fix that (but yes, it's a separate issue).
Quoted 31 lines
Quoted 18 lines
Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml +3
-5- - description: Display vsync clock + maxItems: 4 clock-names: minItems: 1 - items: - - const: iface - - const: bus - - const: vsync + maxItems: 4 "#address-cells": const: 1@@ -69,6 +63,30 @@ properties: items: - description: MDSS_CORE reset +oneOf:Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml properties: · line 76
Quoted 10 lines
Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml +10
-0+ - properties: + clocks: + minItems: 3 + maxItems: 4 + + clock-names: + minItems: 3 + items: + - const: iface + - const: busBTW, sc7180-mdss uses here ahb name and calls it "AHB clock from dispcc".
Quoted 2 lines
SM8250 won't match here either. Maybe this should be reworked to specify limits here but not the names and actual clocks? IOW, drop entire oneOf?
SC7180 and SM8250 use platform-specific bindings (qcom,sc7180-mdss.yaml and qcom,sm8250-mdss.yaml). This file is used only for older platforms (msm8916, msm8996, etc).
Quoted 6 lines
There were a lot, a lot of changes to MDSS/DPU bindings recently, so I am really loosing track what is done where and when.
There are also few separate patchsets from you on the lists. Could they be combined into one cleanup?
Ack, I'll merge them into a single patchset.
Quoted 10 lines
I understand that sometimes new cleanup is needed after old cleanup finished (I had the same with pinctrl), so it is not a complain.
Another problem (and this time I complain) is that several of your patchsets were sent, discussed and then without any notice applied. No message that a patchset was applied to some tree. Look:
https://lore.kernel.org/all/[email protected]/
https://lore.kernel.org/all/[email protected]/
Quoted 6 lines
Nothing. Silent application. If you are the maintainer which picks up the patch, please always, always send message that they are applied. Patchwork does it automatically, b4 can do it easily as well. If you use other tools - use other tools for sending it. Otherwise things are discussed on mailing lists, receive several comments and there is never a resubmit but instead they show in the tree.
Unfortunately freedreno uses patchwork-fdo, which doesn't send notifications. And the fdo fork is not supported by b4. I checked what would be necessary to enable support in b4. Unfortunately several API changes would be necessary. So this is a long process. But we are open to any suggestions on how to improve the process. Currently all three maintainers (Rob, Abhinav and me) keep the patch status in the patchwork, but that's all.
Signature · 2 lines
With best wishes Dmitry
Re: [PATCH v2 1/4] dt-bindings: display/msm: add core clock to the mdss bindings
Quoted 59 lines · Dmitry Baryshkov
Quoted 15 lines · Krzysztof Kozlowski
Quoted 14 lines · Dmitry Baryshkov
Add (optional) core clock to the mdss bindings to let the MDSS driver access harware registers before MDP driver probes.
Signed-off-by Dmitry Baryshkov <[email protected]>--- .../bindings/display/msm/qcom,mdss.yaml | 34 ++++++++++++++----- 1 file changed, 26 insertions(+), 8 deletions(-)Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml +0
-0@@ -45,17 +45,11 @@ properties:Quoted 8 lines
Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml properties: · line 50
Quoted 5 lines
Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml +0
-3clocks: minItems: 1 - items: - - description: Display abh clock - - description: Display axi clockNot related to this patch, but it is a bit surprising to see AXI clock optional.
Hmm, There is one defined downstream. Probably we should fix that (but yes, it's a separate issue).
Quoted 31 lines
Quoted 18 lines
Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml +3
-5- - description: Display vsync clock + maxItems: 4 clock-names: minItems: 1 - items: - - const: iface - - const: bus - - const: vsync + maxItems: 4 "#address-cells": const: 1@@ -69,6 +63,30 @@ properties: items: - description: MDSS_CORE reset +oneOf:Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml properties: · line 76
Quoted 10 lines
Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml +10
-0+ - properties: + clocks: + minItems: 3 + maxItems: 4 + + clock-names: + minItems: 3 + items: + - const: iface + - const: busBTW, sc7180-mdss uses here ahb name and calls it "AHB clock from dispcc".
Quoted 6 lines
Quoted 2 lines
SM8250 won't match here either. Maybe this should be reworked to specify limits here but not the names and actual clocks? IOW, drop entire oneOf?
SC7180 and SM8250 use platform-specific bindings (qcom,sc7180-mdss.yaml and qcom,sm8250-mdss.yaml). This file is used only for older platforms (msm8916, msm8996, etc).
Ah, right. It's a bit confusing to have bindings split into files:
1. mdss-common
2. mdss
3. device specific
but I guess fixing this would be another chunk of work.
Quoted 27 lines
Quoted 7 lines
There were a lot, a lot of changes to MDSS/DPU bindings recently, so I am really loosing track what is done where and when.
There are also few separate patchsets from you on the lists. Could they be combined into one cleanup?
Ack, I'll merge them into a single patchset.
Quoted 10 lines
I understand that sometimes new cleanup is needed after old cleanup finished (I had the same with pinctrl), so it is not a complain.
Another problem (and this time I complain) is that several of your patchsets were sent, discussed and then without any notice applied. No message that a patchset was applied to some tree. Look:
https://lore.kernel.org/all/[email protected]/
https://lore.kernel.org/all/[email protected]/Quoted 6 lines
Nothing. Silent application. If you are the maintainer which picks up the patch, please always, always send message that they are applied. Patchwork does it automatically, b4 can do it easily as well. If you use other tools - use other tools for sending it. Otherwise things are discussed on mailing lists, receive several comments and there is never a resubmit but instead they show in the tree.
Quoted 7 lines
Unfortunately freedreno uses patchwork-fdo, which doesn't send notifications. And the fdo fork is not supported by b4. I checked what would be necessary to enable support in b4. Unfortunately several API changes would be necessary. So this is a long process. But we are open to any suggestions on how to improve the process. Currently all three maintainers (Rob, Abhinav and me) keep the patch status in the patchwork, but that's all.
And how other freedesktop.org patchwork users notify? Manually or is there some hook? I notice only Exynos DRM where maintainer sends manual "Applied" messages.
Best regards,
Krzysztof
Re: [PATCH v2 1/4] dt-bindings: display/msm: add core clock to the mdss bindings
Quoted 67 lines · Krzysztof Kozlowski
Quoted 59 lines · Dmitry Baryshkov
Quoted 15 lines · Krzysztof Kozlowski
Quoted 14 lines · Dmitry Baryshkov
Add (optional) core clock to the mdss bindings to let the MDSS driver access harware registers before MDP driver probes.
Signed-off-by Dmitry Baryshkov <[email protected]>--- .../bindings/display/msm/qcom,mdss.yaml | 34 ++++++++++++++----- 1 file changed, 26 insertions(+), 8 deletions(-)Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml +0
-0@@ -45,17 +45,11 @@ properties:Quoted 8 lines
Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml properties: · line 50
Quoted 5 lines
Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml +0
-3clocks: minItems: 1 - items: - - description: Display abh clock - - description: Display axi clockNot related to this patch, but it is a bit surprising to see AXI clock optional.
Hmm, There is one defined downstream. Probably we should fix that (but yes, it's a separate issue).
Quoted 31 lines
Quoted 18 lines
Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml +3
-5- - description: Display vsync clock + maxItems: 4 clock-names: minItems: 1 - items: - - const: iface - - const: bus - - const: vsync + maxItems: 4 "#address-cells": const: 1@@ -69,6 +63,30 @@ properties: items: - description: MDSS_CORE reset +oneOf:Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml properties: · line 76
Quoted 10 lines
Documentation/devicetree/bindings/display/msm/qcom,mdss.yaml +10
-0+ - properties: + clocks: + minItems: 3 + maxItems: 4 + + clock-names: + minItems: 3 + items: + - const: iface + - const: busBTW, sc7180-mdss uses here ahb name and calls it "AHB clock from dispcc".
Quoted 6 lines
Quoted 2 lines
SM8250 won't match here either. Maybe this should be reworked to specify limits here but not the names and actual clocks? IOW, drop entire oneOf?
SC7180 and SM8250 use platform-specific bindings (qcom,sc7180-mdss.yaml and qcom,sm8250-mdss.yaml). This file is used only for older platforms (msm8916, msm8996, etc).
Quoted 6 lines
Ah, right. It's a bit confusing to have bindings split into files:
1. mdss-common
2. mdss
3. device specificbut I guess fixing this would be another chunk of work.
It comes from the history of display devices on Qualcomm platforms. Older platforms used single compatible entry: qcom,mdss (and qcom,mdp5 for the corresponding MDP/DPU device). Then at the sdm845 point there was a change: per-SoC compatibles for both MDSS and DPU. But older devices still have the qcom,mdss compat string. Moreover this change also introduced a shift in the DT (some properties were moved from MDP to the MDSS device, e.g. interconnects and iommus). So the mdss-common lists common properties of new-style bindings, but it is not applicable to old platforms.
Thus we ended up in a situation where we have:
- qcom,mdss for old devices. Maybe it better be renamed to qcom,mdss-other?
- qcom,SoC-mdss + mdss-common
The same situation applies to the MDP/DPU:
- qcom,mdp5
- qcom,SoC-dpu + dpu-common
Quoted 36 lines
Quoted 28 lines
Quoted 8 lines
There were a lot, a lot of changes to MDSS/DPU bindings recently, so I am really loosing track what is done where and when.
There are also few separate patchsets from you on the lists. Could they be combined into one cleanup?
Ack, I'll merge them into a single patchset.
Quoted 10 lines
I understand that sometimes new cleanup is needed after old cleanup finished (I had the same with pinctrl), so it is not a complain.
Another problem (and this time I complain) is that several of your patchsets were sent, discussed and then without any notice applied. No message that a patchset was applied to some tree. Look:
https://lore.kernel.org/all/[email protected]/
https://lore.kernel.org/all/[email protected]/Quoted 6 lines
Nothing. Silent application. If you are the maintainer which picks up the patch, please always, always send message that they are applied. Patchwork does it automatically, b4 can do it easily as well. If you use other tools - use other tools for sending it. Otherwise things are discussed on mailing lists, receive several comments and there is never a resubmit but instead they show in the tree.
Quoted 7 lines
Unfortunately freedreno uses patchwork-fdo, which doesn't send notifications. And the fdo fork is not supported by b4. I checked what would be necessary to enable support in b4. Unfortunately several API changes would be necessary. So this is a long process. But we are open to any suggestions on how to improve the process. Currently all three maintainers (Rob, Abhinav and me) keep the patch status in the patchwork, but that's all.
Quoted 3 lines
And how other freedesktop.org patchwork users notify? Manually or is there some hook? I notice only Exynos DRM where maintainer sends manual "Applied" messages.
I fear there are no other good options. I picked up maintenance practices from Rob, who doesn't send `applied' message. Maybe it's something to change.
Quoted 4 lines
Best regards,
Krzysztof
Signature · 2 lines
With best wishes Dmitry
Re: [PATCH v2 1/4] dt-bindings: display/msm: add core clock to the mdss bindings
In reply to Dmitry BaryshkovQuoted 2 lines · Dmitry Baryshkov
Quoted 1 line · Krzysztof Kozlowski
On 09/01/2023 01:52, Dmitry Baryshkov wrote:
[skipped]
Quoted 8 lines
Quoted 6 lines
There were a lot, a lot of changes to MDSS/DPU bindings recently, so I am really loosing track what is done where and when.
There are also few separate patchsets from you on the lists. Could they be combined into one cleanup?
Ack, I'll merge them into a single patchset.
I gave it some thought... Putting small non-mdss/mdp fixes aside, there are three series, which I'm trying to track:
- MDP5 schema conversion + per-SoC compatibles for MDP5 [1] no dependencies
- mdss/mdp/dpu -> display-subsystem, display-controller rename [2] depends on [1]
- mdp5 core clock support [3]
depends on [1]
I think I'll target on merging [1] and [2] first, since they are purely DT + schema changes. If you prefer I can squash them for the next iteration or I can keep them separate.
For [3] I'll wait for first two to be in the proper shape, since it also contributes driver changes (and I don't want to have additional interlocks here).
[1] https://lore.kernel.org/linux-arm-msm/[email protected]/
[2] https://lore.kernel.org/linux-arm-msm/[email protected]/
[3] https://lore.kernel.org/linux-arm-msm/[email protected]/
Signature · 2 lines
With best wishes Dmitry
Rob Herring
maintainerRe: [PATCH v2 1/4] dt-bindings: display/msm: add core clock to the mdss bindings
In reply to Dmitry BaryshkovQuoted 8 lines · Dmitry Baryshkov
Add (optional) core clock to the mdss bindings to let the MDSS driver access harware registers before MDP driver probes.
Signed-off-by Dmitry Baryshkov <[email protected]>--- .../bindings/display/msm/qcom,mdss.yaml | 34 ++++++++++++++----- 1 file changed, 26 insertions(+), 8 deletions(-)
Running 'make dtbs_check' with the schema in this patch gives the following warnings. Consider if they are expected or the schema is incorrect. These may not be new warnings.
Note that it is not yet a requirement to have 0 warnings for dtbs_check. This will change in the future.
Full log is available here: https://patchwork.ozlabs.org/project/devicetree-bindings/patch/[email protected]
mdss@1a00000: mdp@1a01000:compatible:0: 'qcom,mdp5' was expected
arch/arm64/boot/dts/qcom/sdm632-fairphone-fp3.dtb
mdss@1a00000: mdp@1a01000:compatible: ['qcom,msm8953-mdp5', 'qcom,mdp5'] is too long
arch/arm64/boot/dts/qcom/sdm632-fairphone-fp3.dtb
mdss@900000: phy@9a0600:compatible:0: 'qcom,hdmi-phy-8996' is not one of ['qcom,dsi-phy-14nm', 'qcom,dsi-phy-14nm-660', 'qcom,dsi-phy-14nm-8953', 'qcom,dsi-phy-20nm', 'qcom,dsi-phy-28nm-hpm', 'qcom,dsi-phy-28nm-lp']
arch/arm64/boot/dts/qcom/apq8096-db820c.dtb arch/arm64/boot/dts/qcom/apq8096-ifc6640.dtb arch/arm64/boot/dts/qcom/msm8996-mtp.dtb arch/arm64/boot/dts/qcom/msm8996-oneplus3.dtb arch/arm64/boot/dts/qcom/msm8996-oneplus3t.dtb arch/arm64/boot/dts/qcom/msm8996pro-xiaomi-natrium.dtb arch/arm64/boot/dts/qcom/msm8996pro-xiaomi-scorpio.dtb arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-dora.dtb arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-kagura.dtb arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone-keyaki.dtb arch/arm64/boot/dts/qcom/msm8996-xiaomi-gemini.dtb
PATCH v2 2/4 drm/msm/mdss: enable optional core clock for MDP5 MDSS
In reply to Dmitry BaryshkovEnable (optional) core (MDP_CLK) clock that allows accessing HW_REV registers during the platform init.
--- drivers/gpu/drm/msm/msm_mdss.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/gpu/drm/msm/msm_mdss.c +2 -1
@@ -355,7 +355,7 @@ static int msm_mdss_reset(struct device *dev)/* * MDP5 MDSS uses at most three specified clocks. */ -#define MDP5_MDSS_NUM_CLOCKS 3 +#define MDP5_MDSS_NUM_CLOCKS 4static int mdp5_mdss_parse_clock (struct platform_device *pdev,struct clk_bulk_data **clocks) {struct clk_bulk_data *bulk;
@@ -372,6 +372,7 @@ static int mdp5_mdss_parse_clock(struct platform_device *pdev, struct clk_bulk_d bulk[num_clocks++].id ="iface" ; bulk[num_clocks++].id ="bus" ; bulk[num_clocks++].id ="vsync" ; + bulk[num_clocks++].id ="core" ;/* for hw_rev access */ ret =devm_clk_bulk_get_optional (&pdev->dev, num_clocks, bulk);if (ret)
Signature · 1 line
2.39.0
PATCH v2 3/4 drm/msm/mdss: check for core clk before accessing HW_REV
In reply to Dmitry BaryshkovRather than checking whether the platform is an mdp5 or dpu platform, check if the MDP_CLK is provided or not before trying to access HW_REV (and skip reading the registers if the clock is not provided by the DT).
--- drivers/gpu/drm/msm/msm_mdss.c | 22 +++++++++++++++++----- 1 file changed, 17 insertions(+), 5 deletions(-)
drivers/gpu/drm/msm/msm_mdss.c +17 -5
@@ -35,7 +35,6 @@ struct msm_mdss {void __iomem *mmio;struct clk_bulk_data *clocks;size_t num_clocks; -bool is_mdp5;struct {unsigned long enabled_mask;struct irq_domain *domain;
@@ -230,6 +229,19 @@ static void msm_mdss_setup_ubwc_dec_40(struct msm_mdss *msm_mdss, } } +static bool msm_mdss_has_clock (struct msm_mdss *msm_mdss,const char *name) +{ +unsigned int i; + +for (i =0 ; i < msm_mdss->num_clocks; i++) { +if (!strcmp (msm_mdss->clocks[i].id, name) && + msm_mdss->clocks[i].clk) +return true; + } + +return false; +} +static int msm_mdss_enable (struct msm_mdss *msm_mdss) {int ret;
@@ -249,10 +261,11 @@ static int msm_mdss_enable(struct msm_mdss *msm_mdss) }/* -* HW_REV requires MDSS_MDP_CLK, which is not enabled by the mdss on -* mdp5 hardware. Skip reading it for now. +* HW_REV requires MDSS_MDP_CLK, which is not used for MDSS device in +* older device trees. Skip accessing registers if the clock is not +* present. */ -if (msm_mdss->is_mdp5) +if (!msm_mdss_has_clock (msm_mdss,"core" ))return 0 ; hw_rev =readl_relaxed (msm_mdss->mmio +HW_REV );
@@ -419,7 +432,6 @@ static struct msm_mdss *msm_mdss_init(struct platform_device *pdev, bool is_mdp5return ERR_PTR (ret); } msm_mdss->num_clocks = ret; - msm_mdss->is_mdp5 = is_mdp5; msm_mdss->dev = &pdev->dev;
Signature · 1 line
2.39.0
PATCH v2 4/4 drm/msm/mdss: move is_mdp5 condition to msm_mdss_init
In reply to Dmitry BaryshkovMove is_mdp5 check to a more logical place, to the msm_mdss_init(), rather than getting it in the mdss_probe() and passing it then as an argument.
--- drivers/gpu/drm/msm/msm_mdss.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/gpu/drm/msm/msm_mdss.c +3 -3
@@ -396,8 +396,9 @@ static int mdp5_mdss_parse_clock(struct platform_device *pdev, struct clk_bulk_dreturn num_clocks; } -static struct msm_mdss *msm_mdss_init (struct platform_device *pdev,bool is_mdp5) +static struct msm_mdss *msm_mdss_init (struct platform_device *pdev) { +bool is_mdp5 =of_device_is_compatible (pdev->dev.of_node,"qcom,mdss" );struct msm_mdss *msm_mdss;int ret;int irq;
@@ -494,11 +495,10 @@ static const struct dev_pm_ops mdss_pm_ops = {static int mdss_probe (struct platform_device *pdev) {struct msm_mdss *mdss; -bool is_mdp5 =of_device_is_compatible (pdev->dev.of_node,"qcom,mdss" );struct device *dev = &pdev->dev;int ret; - mdss =msm_mdss_init (pdev, is_mdp5); + mdss =msm_mdss_init (pdev);if (IS_ERR (mdss))return PTR_ERR (mdss);
Signature · 1 line
2.39.0