Improve K3-am625-sk support (USB, MMC)
Subsystems (2)
v4 cover Improve K3-am625-sk support (USB, MMC)
This series picks up a few patches from the TI BSP tree that unfortunately didn't make it upstream thusfar.
The first patch improve SD card compatibility (allowing U1 class cards to be used), the remaining ones add USB support.
The type-c connector isn't entirely modelled with these changes as it goes through a TPS6598 PD controller. Unfortunately the dtb bindings for that currently require an irq line, which is not connected on E1 and E2 version boards. The patchese to support this setup unfortunately didn't land yet[0].. As such the last patch ignored the PD controller and simply configures usb0 as periphal only rather then mode switch capable, which at least gives some basic usability of that USB port.
0: https://lore.kernel.org/lkml/[email protected]/T/
Changes in v4:
- Disable new usbss nodes by default in the dtsi and enable in the dts
- Drop unneeded disabled nodes in board dts
Changes in v3:
- Rebased against current ti-next aka 6.2-rc1
- Add Martyn's tested-by
Changes in v2:
- Rebase against linux-next 20221220
Aswath Govindraju (2):
arm64: dts: ti: k3-am62-main: Add support for USB
arm64: dts: ti: k3-am625-sk: Add support for USB
Nitin Yadav (1):
arm64: dts: ti: k3-am62-main: Update OTAP and ITAP delay select
arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 92 ++++++++++++++++++------ arch/arm64/boot/dts/ti/k3-am625-sk.dts | 27 +++++++ 2 files changed, 97 insertions(+), 22 deletions(-)
Signature · 7 lines
2.39.0 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v4 1/3 arm64: dts: ti: k3-am62-main: Update OTAP and ITAP delay select
From: Nitin Yadav <[email protected]>
UHS Class U1 sd-card are not getting detected due to incorrect OTAP/ITAP delay select values in linux. Update OTAP and ITAP delay select values for various speed modes. For sdhci0, update OTAP delay values for ddr52 & HS200 and add ITAP delay for legacy & mmc-hs. For sdhci1 & sdhci2, update OTAP & ITAP delay select recommended as in RIOT for various speed modes.
---
(no changes since v3)
Changes in v3:
- Rebased against current ti-next aka 6.2-rc1
- Add Martyn's tested-by
Changes in v2:
- Rebase against linux-next 20221220
arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 46 ++++++++++++------------ 1 file changed, 24 insertions(+), 22 deletions(-)
arch/arm64/boot/dts/ti/k3-am62-main.dtsi +24 -22
@@ -501,8 +501,10 @@ sdhci0: mmc@fa10000 { ti,clkbuf-sel = <0x7>; ti,otap-del-sel-legacy = <0x0>; ti,otap-del-sel-mmc-hs = <0x0>; - ti,otap-del-sel-ddr52 = <0x9>; - ti,otap-del-sel-hs200 = <0x6>; + ti,otap-del-sel-ddr52 = <0x5>; + ti,otap-del-sel-hs200 = <0x5>; + ti,itap-del-sel-legacy = <0xa>; + ti,itap-del-sel-mmc-hs = <0x1>; status = "disabled"; };
@@ -514,17 +516,17 @@ sdhci1: mmc@fa00000 { clocks = <&k3_clks 58 5>, <&k3_clks 58 6>; clock-names = "clk_ahb", "clk_xin"; ti,trm-icp = <0x2>; - ti,otap-del-sel-legacy = <0x0>; + ti,otap-del-sel-legacy = <0x8>; ti,otap-del-sel-sd-hs = <0x0>; - ti,otap-del-sel-sdr12 = <0xf>; - ti,otap-del-sel-sdr25 = <0xf>; - ti,otap-del-sel-sdr50 = <0xc>; - ti,otap-del-sel-sdr104 = <0x6>; - ti,otap-del-sel-ddr50 = <0x9>; - ti,itap-del-sel-legacy = <0x0>; - ti,itap-del-sel-sd-hs = <0x0>; - ti,itap-del-sel-sdr12 = <0x0>; - ti,itap-del-sel-sdr25 = <0x0>; + ti,otap-del-sel-sdr12 = <0x0>; + ti,otap-del-sel-sdr25 = <0x0>; + ti,otap-del-sel-sdr50 = <0x8>; + ti,otap-del-sel-sdr104 = <0x7>; + ti,otap-del-sel-ddr50 = <0x4>; + ti,itap-del-sel-legacy = <0xa>; + ti,itap-del-sel-sd-hs = <0x1>; + ti,itap-del-sel-sdr12 = <0xa>; + ti,itap-del-sel-sdr25 = <0x1>; ti,clkbuf-sel = <0x7>; bus-width = <4>; status = "disabled";
@@ -538,17 +540,17 @@ sdhci2: mmc@fa20000 { clocks = <&k3_clks 184 5>, <&k3_clks 184 6>; clock-names = "clk_ahb", "clk_xin"; ti,trm-icp = <0x2>; - ti,otap-del-sel-legacy = <0x0>; + ti,otap-del-sel-legacy = <0x8>; ti,otap-del-sel-sd-hs = <0x0>; - ti,otap-del-sel-sdr12 = <0xf>; - ti,otap-del-sel-sdr25 = <0xf>; - ti,otap-del-sel-sdr50 = <0xc>; - ti,otap-del-sel-sdr104 = <0x6>; - ti,otap-del-sel-ddr50 = <0x9>; - ti,itap-del-sel-legacy = <0x0>; - ti,itap-del-sel-sd-hs = <0x0>; - ti,itap-del-sel-sdr12 = <0x0>; - ti,itap-del-sel-sdr25 = <0x0>; + ti,otap-del-sel-sdr12 = <0x0>; + ti,otap-del-sel-sdr25 = <0x0>; + ti,otap-del-sel-sdr50 = <0x8>; + ti,otap-del-sel-sdr104 = <0x7>; + ti,otap-del-sel-ddr50 = <0x8>; + ti,itap-del-sel-legacy = <0xa>; + ti,itap-del-sel-sd-hs = <0xa>; + ti,itap-del-sel-sdr12 = <0xa>; + ti,itap-del-sel-sdr25 = <0x1>; ti,clkbuf-sel = <0x7>; status = "disabled"; };
Signature · 1 line
2.39.0
PATCH v4 2/3 arm64: dts: ti: k3-am62-main: Add support for USB
In reply to Sjoerd SimonsFrom: Aswath Govindraju <[email protected]>
AM62 SoC has two instances of USB on it. Therefore, add support for the same.
---
Changes in v4:
- Default to status="disabled" for usbss nodes
Changes in v3:
- Rebased against current ti-next aka 6.2-rc1
- Add Martyn's tested-by
Changes in v2:
- Rebase against linux-next 20221220
arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 46 ++++++++++++++++++++++++ 1 file changed, 46 insertions(+)
arch/arm64/boot/dts/ti/k3-am62-main.dtsi +46 -0
@@ -555,6 +555,52 @@ sdhci2: mmc@fa20000 { status = "disabled"; }; + usbss0: dwc3-usb@f900000 { + compatible = "ti,am62-usb"; + reg = <0x00 0x0f900000 0x00 0x800>; + clocks = <&k3_clks 161 3>; + clock-names = "ref"; + ti,syscon-phy-pll-refclk = <&wkup_conf 0x4008>; + #address-cells = <2>; + #size-cells = <2>; + power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>; + ranges; + status = "disabled"; + + usb0: usb@31000000 { + compatible = "snps,dwc3"; + reg =<0x00 0x31000000 0x00 0x50000>; + interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */ + <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */ + interrupt-names = "host", "peripheral"; + maximum-speed = "high-speed"; + dr_mode = "otg"; + }; + }; + + usbss1: dwc3-usb@f910000 { + compatible = "ti,am62-usb"; + reg = <0x00 0x0f910000 0x00 0x800>; + clocks = <&k3_clks 162 3>; + clock-names = "ref"; + ti,syscon-phy-pll-refclk = <&wkup_conf 0x4018>; + #address-cells = <2>; + #size-cells = <2>; + power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>; + ranges; + status = "disabled"; + + usb1: usb@31100000 { + compatible = "snps,dwc3"; + reg =<0x00 0x31100000 0x00 0x50000>; + interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */ + <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */ + interrupt-names = "host", "peripheral"; + maximum-speed = "high-speed"; + dr_mode = "otg"; + }; + }; + fss: bus@fc00000 { compatible = "simple-bus"; reg = <0x00 0x0fc00000 0x00 0x70000>;
Signature · 7 lines
2.39.0 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v4 3/3 arm64: dts: ti: k3-am625-sk: Add support for USB
In reply to Sjoerd SimonsFrom: Aswath Govindraju <[email protected]>
AM62 SoC has two instances of USB and they are brought on to the board in the following way,
-> USB0 instance
- This is brought out to a USB TypeC connector on board through TPS6598 PD controller. The PD controller should decide the role based on CC pin in the connector. Unfortunately the irq line for the TPS isn't hooked up which is a mode not yet support by the driver (some patches were submitted earlier this year[0]). So for now the PD controller is left out and peripheral mode chosen.
-> USB1 instance
- This is brought out to a USB TypeA connector on board.
Therefore, add the required device tree support for the above in the board dts file.
0: https://lore.kernel.org/lkml/[email protected]/T/
---
Changes in v4:
- Disable new usbss nodes by default in the dtsi and enable in the dts
- Drop unneeded disabled nodes in board dts
- Drop unneeded nodes
- Enable usbss nodes
- Small typo fix
Changes in v3:
- Rebased against current ti-next aka 6.2-rc1
- Add Martyn's tested-by
Changes in v2:
- Rebase against linux-next 20221220
arch/arm64/boot/dts/ti/k3-am625-sk.dts | 27 ++++++++++++++++++++++++++ 1 file changed, 27 insertions(+)
arch/arm64/boot/dts/ti/k3-am625-sk.dts +27 -0
@@ -24,6 +24,8 @@ aliases { spi0 = &ospi0; ethernet0 = &cpsw_port1; ethernet1 = &cpsw_port2; + usb0 = &usb0; + usb1 = &usb1; }; chosen {
@@ -284,6 +286,12 @@ main_gpio1_ioexp_intr_pins_default: main-gpio1-ioexp-intr-pins-default { AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */ >; }; + + main_usb1_pins_default: main-usb1-pins-default { + pinctrl-single,pins = < + AM62X_IOPAD(0x0258, PIN_OUTPUT, 0) /* (F18) USB1_DRVVBUS */ + >; + }; }; &wkup_uart0 {
@@ -464,3 +472,22 @@ partition@3fc0000 { }; }; }; + +&usbss0 { + status = "okay"; + ti,vbus-divider; +}; + +&usbss1 { + status = "okay"; +}; + +&usb0 { + dr_mode = "peripheral"; +}; + +&usb1 { + dr_mode = "host"; + pinctrl-names = "default"; + pinctrl-0 = <&main_usb1_pins_default>; +};
Signature · 7 lines
2.39.0 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Hi Sjoerd Simons,
Quoted 14 lines · Sjoerd Simons
This series picks up a few patches from the TI BSP tree that unfortunately didn't make it upstream thusfar.
The first patch improve SD card compatibility (allowing U1 class cards to be used), the remaining ones add USB support.
The type-c connector isn't entirely modelled with these changes as it goes through a TPS6598 PD controller. Unfortunately the dtb bindings for that currently require an irq line, which is not connected on E1 and E2 version boards. The patchese to support this setup unfortunately didn't land yet[0].. As such the last patch ignored the PD controller and simply configures usb0 as periphal only rather then mode switch capable, which at least gives some basic usability of that USB port.
Quoted 1 line
[...]
I have applied the following to branch ti-k3-next on [1]. Thank you!
[1/3] arm64: dts: ti: k3-am62-main: Update OTAP and ITAP delay select
commit: bd2912f400934d71ecb040f625685b886ccdcc20
[2/3] arm64: dts: ti: k3-am62-main: Add support for USB
commit: 2240f96cf3cd0f74f5c349fb212c4176627f69b0
[3/3] arm64: dts: ti: k3-am625-sk: Add support for USB
commit: 2d94dfc438853dca9b390a3f32fe5331c336fd28All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent up the chain during the next merge window (or sooner if it is a relevant bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git
--
Vignesh