SM8350 Display DTS

index fafd92edc855..c78cdaa4adcb 100644
@@ -3,6 +3,7 @@
  * Copyright (c) 2020, Linaro Limited
  */
 
+#include <dt-bindings/interconnect/qcom,sm8350.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,dispcc-sm8350.h>
 #include <dt-bindings/clock/qcom,gcc-sm8350.h>

@@ -2620,14 +2621,302 @@ usb_2_dwc3: usb@a800000 {
 			};
 		};
 
+		mdss: display-subsystem@ae00000 {
+			compatible = "qcom,sm8350-mdss";
+			reg = <0 0x0ae00000 0 0x1000>;
+			reg-names = "mdss";
+
+			interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>,
+					<&mmss_noc MASTER_MDP1 0 &mc_virt SLAVE_EBI1 0>;
+			interconnect-names = "mdp0-mem", "mdp1-mem";
+
+			power-domains = <&dispcc MDSS_GDSC>;
+			resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
+
+			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+				 <&gcc GCC_DISP_HF_AXI_CLK>,
+				 <&gcc GCC_DISP_SF_AXI_CLK>,
+				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
+			clock-names = "iface", "bus", "nrt_bus", "core";
+
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			iommus = <&apps_smmu 0x820 0x402>;
+
+			status = "disabled";
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			dpu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				/* TODO: opp-200000000 should work with
+				 * &rpmhpd_opp_low_svs, but one some of
+				 * sm8350_hdk boards reboot using this
+				 * opp.
+				 */
+				opp-200000000 {
+					opp-hz = /bits/ 64 <200000000>;
+					required-opps = <&rpmhpd_opp_svs>;
+				};
+
+				opp-300000000 {
+					opp-hz = /bits/ 64 <300000000>;
+					required-opps = <&rpmhpd_opp_svs>;
+				};
+
+				opp-345000000 {
+					opp-hz = /bits/ 64 <345000000>;
+					required-opps = <&rpmhpd_opp_svs_l1>;
+				};
+
+				opp-460000000 {
+					opp-hz = /bits/ 64 <460000000>;
+					required-opps = <&rpmhpd_opp_nom>;
+				};
+			};
+
+			mdss_mdp: display-controller@ae01000 {
+				compatible = "qcom,sm8350-dpu";
+				reg = <0 0x0ae01000 0 0x8f000>,
+				      <0 0x0aeb0000 0 0x2008>;
+				reg-names = "mdp", "vbif";
+
+				clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
+					<&gcc GCC_DISP_SF_AXI_CLK>,
+					<&dispcc DISP_CC_MDSS_AHB_CLK>,
+					<&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+					<&dispcc DISP_CC_MDSS_MDP_CLK>,
+					<&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				clock-names = "bus",
+					      "nrt_bus",
+					      "iface",
+					      "lut",
+					      "core",
+					      "vsync";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				assigned-clock-rates = <19200000>;
+
+				operating-points-v2 = <&dpu_opp_table>;
+				power-domains = <&rpmhpd SM8350_MMCX>;
+
+				interrupt-parent = <&mdss>;
+				interrupts = <0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dpu_intf1_out: endpoint {
+							remote-endpoint = <&dsi0_in>;
+						};
+					};
+				};
+			};
+
+			mdss_dsi0: dsi@ae94000 {
+				compatible = "qcom,mdss-dsi-ctrl";
+				reg = <0 0x0ae94000 0 0x400>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4>;
+
+				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+					 <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&gcc GCC_DISP_HF_AXI_CLK>;
+				clock-names = "byte",
+					      "byte_intf",
+					      "pixel",
+					      "core",
+					      "iface",
+					      "bus";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
+				assigned-clock-parents = <&mdss_dsi0_phy 0>,
+							 <&mdss_dsi0_phy 1>;
+
+				operating-points-v2 = <&dsi0_opp_table>;
+				power-domains = <&rpmhpd SM8350_MMCX>;
+
+				phys = <&mdss_dsi0_phy>;
+
+				status = "disabled";
+
+				dsi0_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					/* TODO: opp-187500000 should work with
+					 * &rpmhpd_opp_low_svs, but one some of
+					 * sm8350_hdk boards reboot using this
+					 * opp.
+					 */
+					opp-187500000 {
+						opp-hz = /bits/ 64 <187500000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-300000000 {
+						opp-hz = /bits/ 64 <300000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-358000000 {
+						opp-hz = /bits/ 64 <358000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+				};
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dsi0_in: endpoint {
+							remote-endpoint = <&dpu_intf1_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dsi0_out: endpoint {
+						};
+					};
+				};
+			};
+
+			mdss_dsi0_phy: phy@ae94400 {
+				compatible = "qcom,dsi-phy-5nm-8350";
+				reg = <0 0x0ae94400 0 0x200>,
+				      <0 0x0ae94600 0 0x280>,
+				      <0 0x0ae94900 0 0x260>;
+				reg-names = "dsi_phy",
+					    "dsi_phy_lane",
+					    "dsi_pll";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&rpmhcc RPMH_CXO_CLK>;
+				clock-names = "iface", "ref";
+
+				status = "disabled";
+			};
+
+			mdss_dsi1: dsi@ae96000 {
+				compatible = "qcom,mdss-dsi-ctrl";
+				reg = <0 0x0ae96000 0 0x400>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4>;
+
+				clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
+					 <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
+					 <&dispcc DISP_CC_MDSS_ESC1_CLK>,
+					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&gcc GCC_DISP_HF_AXI_CLK>;
+				clock-names = "byte",
+					      "byte_intf",
+					      "pixel",
+					      "core",
+					      "iface",
+					      "bus";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>;
+				assigned-clock-parents = <&mdss_dsi1_phy 0>,
+							 <&mdss_dsi1_phy 1>;
+
+				operating-points-v2 = <&dsi1_opp_table>;
+				power-domains = <&rpmhpd SM8350_MMCX>;
+
+				phys = <&mdss_dsi1_phy>;
+
+				status = "disabled";
+
+				dsi1_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					/* TODO: opp-187500000 should work with
+					 * &rpmhpd_opp_low_svs, but one some of
+					 * sm8350_hdk boards reboot using this
+					 * opp.
+					 */
+					opp-187500000 {
+						opp-hz = /bits/ 64 <187500000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-300000000 {
+						opp-hz = /bits/ 64 <300000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-358000000 {
+						opp-hz = /bits/ 64 <358000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+				};
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dsi1_in: endpoint {
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dsi1_out: endpoint {
+						};
+					};
+				};
+			};
+
+			mdss_dsi1_phy: phy@ae96400 {
+				compatible = "qcom,dsi-phy-5nm-8350";
+				reg = <0 0x0ae96400 0 0x200>,
+				      <0 0x0ae96600 0 0x280>,
+				      <0 0x0ae96900 0 0x260>;
+				reg-names = "dsi_phy",
+					    "dsi_phy_lane",
+					    "dsi_pll";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&rpmhcc RPMH_CXO_CLK>;
+				clock-names = "iface", "ref";
+
+				status = "disabled";
+			};
+		};
+
 		dispcc: clock-controller@af00000 {
 			compatible = "qcom,sm8350-dispcc";
 			reg = <0 0x0af00000 0 0x10000>;
 			clocks = <&rpmhcc RPMH_CXO_CLK>,
-				 <0>,
-				 <0>,
-				 <0>,
-				 <0>,
+				 <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>,
+				 <0>, <0>,
 				 <0>,
 				 <0>;
 			clock-names = "bi_tcxo",

index 26a608144886..7878f42e9378 100644
@@ -221,10 +221,32 @@ &cdsp {
 	firmware-name = "qcom/sm8350/cdsp.mbn";
 };
 
+&dispcc {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	vdda-supply = <&vreg_l6b_1p2>;
+	status = "okay";
+};
+
+&mdss_dsi0_phy  {
+	vdds-supply = <&vreg_l5b_0p88>;
+	status = "okay";
+};
+
 &gpi_dma1 {
 	status = "okay";
 };
 
+&mdss {
+	status = "okay";
+};
+
+&mdss_mdp {
+	status = "okay";
+};
+
 &mpss {
 	status = "okay";
 	firmware-name = "qcom/sm8350/modem.mbn";

index 7878f42e9378..49ff3033c120 100644
@@ -20,6 +20,17 @@ chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&lt9611_out>;
+			};
+		};
+	};
+
 	vph_pwr: vph-pwr-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "vph_pwr";

@@ -29,6 +40,31 @@ vph_pwr: vph-pwr-regulator {
 		regulator-always-on;
 		regulator-boot-on;
 	};
+
+	lt9611_1v2: lt9611-1v2-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "LT9611_1V2";
+
+		vin-supply = <&vph_pwr>;
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		gpio = <&tlmm 49 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+
+	lt9611_3v3: lt9611-3v3-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "LT9611_3V3";
+
+		vin-supply = <&vreg_bob>;
+		gpio = <&tlmm 47 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		regulator-boot-on;
+		regulator-always-on;
+	};
 };
 
 &adsp {

@@ -228,6 +264,15 @@ &dispcc {
 &mdss_dsi0 {
 	vdda-supply = <&vreg_l6b_1p2>;
 	status = "okay";
+
+	ports {
+		port@1 {
+			endpoint {
+				remote-endpoint = <&lt9611_a>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
 };
 
 &mdss_dsi0_phy  {

@@ -239,6 +284,46 @@ &gpi_dma1 {
 	status = "okay";
 };
 
+&i2c15 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	lt9611_codec: hdmi-bridge@2b {
+		compatible = "lontium,lt9611uxc";
+		reg = <0x2b>;
+
+		interrupts-extended = <&tlmm 50 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>;
+
+		vdd-supply = <&lt9611_1v2>;
+		vcc-supply = <&lt9611_3v3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lt9611_state>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lt9611_a: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				lt9611_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+		};
+	};
+};
+
 &mdss {
 	status = "okay";
 };

@@ -256,6 +341,10 @@ &qupv3_id_0 {
 	status = "okay";
 };
 
+&qupv3_id_2 {
+	status = "okay";
+};
+
 &slpi {
 	status = "okay";
 	firmware-name = "qcom/sm8350/slpi.mbn";

@@ -347,4 +436,20 @@ usb_hub_enabled_state: usb-hub-enabled-state {
 		drive-strength = <2>;
 		output-low;
 	};
+
+	lt9611_state: lt9611-state {
+		rst {
+			pins = "gpio48";
+			function = "normal";
+
+			output-high;
+			input-disable;
+		};
+
+		irq {
+			pins = "gpio50";
+			function = "gpio";
+			bias-disable;
+		};
+	};
 };