Skip to contentSkip to conversation

i3c: update dw-i3c-master i3c_clk_cfg function

PATCH Applied Jack Chen 2 participants 2 messages Feb 16, 2023 – Feb 25, 2023

Subsystems (2)
lore
Share & tools
lore

Jack Chen

author
#0 lore raw

PATCH v3 1/1 i3c: update dw-i3c-master i3c_clk_cfg function

Bus-speed could be default(12.5MHz) or defined by users in dts. Dw-i3c-master should not hard-code the initial speed to be I3C_BUS_TYP_I3C_SCL_RATE (12.5MHz)
And because of Synopsys's I3C controller limit (hcnt/lcnt register length) and core-clk provided, there is a limit to bus speed, too. For example, when core-clk is 250 MHz, the bus speed cannot be lowered below 1MHz.

Tested: tested with an i3c sensor and captured with a logic analyzer.

---
[v3]
- change the target tree to be i3c/next
[v2]
- replace max with max_t

 drivers/i3c/master/dw-i3c-master.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/i3c/master/dw-i3c-master.c +3 -2
index 51a8608203de..48954d3e6571 100644
@@ -531,7 +531,7 @@ static int dw_i3c_clk_cfg(struct dw_i3c_master *master)
 	if (hcnt < SCL_I3C_TIMING_CNT_MIN)
 		hcnt = SCL_I3C_TIMING_CNT_MIN;
 
-	lcnt = DIV_ROUND_UP(core_rate, I3C_BUS_TYP_I3C_SCL_RATE) - hcnt;
+	lcnt = DIV_ROUND_UP(core_rate, master->base.bus.scl_rate.i3c) - hcnt;
 	if (lcnt < SCL_I3C_TIMING_CNT_MIN)
 		lcnt = SCL_I3C_TIMING_CNT_MIN;
 
@@ -541,7 +541,8 @@ static int dw_i3c_clk_cfg(struct dw_i3c_master *master)
 	if (!(readl(master->regs + DEVICE_CTRL) & DEV_CTRL_I2C_SLAVE_PRESENT))
 		writel(BUS_I3C_MST_FREE(lcnt), master->regs + BUS_FREE_TIMING);
 
-	lcnt = DIV_ROUND_UP(I3C_BUS_TLOW_OD_MIN_NS, core_period);
+	lcnt = max_t(u8,
+		     DIV_ROUND_UP(I3C_BUS_TLOW_OD_MIN_NS, core_period), lcnt);
 	scl_timing = SCL_I3C_TIMING_HCNT(hcnt) | SCL_I3C_TIMING_LCNT(lcnt);
 	writel(scl_timing, master->regs + SCL_I3C_OD_TIMING);
 
Signature · 1 line
2.39.2.637.g21b0678d19-goog
maintainer Applied
#1 lore raw
Quoted 9 lines · Jack Chen

Bus-speed could be default(12.5MHz) or defined by users in dts. Dw-i3c-master should not hard-code the initial speed to be I3C_BUS_TYP_I3C_SCL_RATE (12.5MHz)
And because of Synopsys's I3C controller limit (hcnt/lcnt register length) and core-clk provided, there is a limit to bus speed, too. For example, when core-clk is 250 MHz, the bus speed cannot be lowered below 1MHz.

[...]

Applied, thanks!

[1/1] i3c: update dw-i3c-master i3c_clk_cfg function

      commit: 07eac9c306a0efd73a43804b50c88c67696a3c74

Best regards,

Signature · 8 lines
Alexandre Belloni, co-owner and COO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

-- 
linux-i3c mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-i3c