Skip to contentSkip to conversation

Add EMAC3 support for sa8540p-ride

PATCH Superseded Andrew Halaney 5 participants 24 messages Mar 20, 2023 – Mar 22, 2023

Subsystems (10)

v2 of 6 Superseded Latest is v6 →

lore
Share & tools
lore
#0 lore raw

v2 cover Add EMAC3 support for sa8540p-ride

This is a forward port / upstream refactor of code delivered downstream by Qualcomm over at [0] to enable the DWMAC5 based implementation called EMAC3 on the sa8540p-ride dev board.

From what I can tell with the board schematic in hand, as well as the code delivered, the main changes needed are:

1. A new address space layout for /dwmac5/EMAC3 MTL/DMA regs
2. A new programming sequence required for the EMAC3 base platforms

This series makes those adaptations as well as other housekeeping items such as converting dt-bindings to yaml, adding clock descriptions, etc.

[0] https://git.codelinaro.org/clo/la/kernel/ark-5.14/-/commit/510235ad02d7f0df478146fb00d7a4ba74821b17

v1: https://lore.kernel.org/netdev/[email protected]/

Thanks,
Andrew

Andrew Halaney (8):
dt-bindings: net: qcom,ethqos: Add Qualcomm sc8280xp compatibles
clk: qcom: gcc-sc8280xp: Add EMAC GDSCs
arm64: dts: qcom: sc8280xp: Add ethernet nodes
arm64: dts: qcom: sa8540p-ride: Add ethernet nodes
net: stmmac: Remove unnecessary if statement brackets
net: stmmac: dwmac-qcom-ethqos: Respect phy-mode and TX delay
net: stmmac: dwmac-qcom-ethqos: Use loopback_en for all speeds
net: stmmac: dwmac-qcom-ethqos: Add EMAC3 support

Bhupesh Sharma (3):
dt-bindings: net: snps,dwmac: Update interrupt-names
dt-bindings: net: snps,dwmac: Add Qualcomm Ethernet ETHQOS compatibles
dt-bindings: net: qcom,ethqos: Convert bindings to yaml

Brian Masney (1):
net: stmmac: Add EMAC3 variant of dwmac4

 .../devicetree/bindings/net/qcom,ethqos.txt   |  66 ----
 .../devicetree/bindings/net/qcom,ethqos.yaml  | 111 ++++++
 .../devicetree/bindings/net/snps,dwmac.yaml   |   9 +-
 MAINTAINERS                                   |   2 +-
 arch/arm64/boot/dts/qcom/sa8540p-ride.dts     | 181 ++++++++++
 arch/arm64/boot/dts/qcom/sc8280xp.dtsi        |  53 +++
 drivers/clk/qcom/gcc-sc8280xp.c               |  18 +
 .../stmicro/stmmac/dwmac-qcom-ethqos.c        | 161 ++++++---
 drivers/net/ethernet/stmicro/stmmac/dwmac4.h  |  32 +-
 .../net/ethernet/stmicro/stmmac/dwmac4_core.c | 235 ++++++++++--
 .../net/ethernet/stmicro/stmmac/dwmac4_dma.c  | 334 ++++++++++++++----
 .../net/ethernet/stmicro/stmmac/dwmac4_dma.h  |  38 ++
 .../net/ethernet/stmicro/stmmac/dwmac4_lib.c  | 144 ++++++--
 drivers/net/ethernet/stmicro/stmmac/hwif.c    |  29 +-
 drivers/net/ethernet/stmicro/stmmac/hwif.h    |   2 +
 .../ethernet/stmicro/stmmac/stmmac_ethtool.c  |   6 +-
 .../net/ethernet/stmicro/stmmac/stmmac_main.c |  17 +-
 .../net/ethernet/stmicro/stmmac/stmmac_mdio.c |   9 +-
 .../net/ethernet/stmicro/stmmac/stmmac_ptp.c  |   4 +-
 include/dt-bindings/clock/qcom,gcc-sc8280xp.h |   2 +
 include/linux/stmmac.h                        |   1 +
 21 files changed, 1196 insertions(+), 258 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/net/qcom,ethqos.txt
 create mode 100644 Documentation/devicetree/bindings/net/qcom,ethqos.yaml
Signature · 1 line
2.39.2
#1 lore raw

PATCH v2 1/12 dt-bindings: net: snps,dwmac: Update interrupt-names

From: Bhupesh Sharma <[email protected]>

As commit fc191af1bb0d ("net: stmmac: platform: Fix misleading interrupt error msg") noted, not every stmmac based platform makes use of the 'eth_wake_irq' or 'eth_lpi' interrupts.

So, update the 'interrupt-names' inside 'snps,dwmac' YAML bindings to reflect the same.

---

Changes since v1:
* Dropped Krzysztof's Acked-by since changes requested
* Changed interrupt-names items per Krzysztof

 Documentation/devicetree/bindings/net/snps,dwmac.yaml | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
Documentation/devicetree/bindings/net/snps,dwmac.yaml +1 -1
index 16b7d2904696..df4c5d184446 100644
@@ -105,7 +105,7 @@ properties:
     minItems: 1
     items:
       - const: macirq
-      - const: eth_wake_irq
+      - enum: [eth_wake_irq, eth_lpi]
       - const: eth_lpi
 
   clocks:
Signature · 1 line
2.39.2
Reviewed-by on v2 1/12
#2 lore raw

Re: [PATCH net-next v2 01/12] dt-bindings: net: snps,dwmac: Update interrupt-names

Quoted 6 lines · Andrew Halaney

From: Bhupesh Sharma <[email protected]>

As commit fc191af1bb0d ("net: stmmac: platform: Fix misleading interrupt error msg") noted, not every stmmac based platform makes use of the 'eth_wake_irq' or 'eth_lpi' interrupts.

Quoted 6 lines

So, update the 'interrupt-names' inside 'snps,dwmac' YAML bindings to reflect the same.

---

Best regards,
Krzysztof

#3 lore raw

PATCH v2 2/12 dt-bindings: net: snps,dwmac: Add Qualcomm Ethernet ETHQOS compatibles

In reply to Andrew Halaney

From: Bhupesh Sharma <[email protected]>

Add Qualcomm Ethernet ETHQOS compatible checks
in snps,dwmac YAML binding document.

---

Changes since v1:
* None

 Documentation/devicetree/bindings/net/snps,dwmac.yaml | 4 ++++
 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/net/snps,dwmac.yaml +4 -0
index df4c5d184446..154955718246 100644
@@ -65,6 +65,8 @@ properties:
         - ingenic,x2000-mac
         - loongson,ls2k-dwmac
         - loongson,ls7a-dwmac
+        - qcom,qcs404-ethqos
+        - qcom,sm8150-ethqos
         - renesas,r9a06g032-gmac
         - renesas,rzn1-gmac
         - rockchip,px30-gmac
@@ -625,6 +627,8 @@ allOf:
               - ingenic,x1600-mac
               - ingenic,x1830-mac
               - ingenic,x2000-mac
+              - qcom,qcs404-ethqos
+              - qcom,sm8150-ethqos
               - snps,dwmac-4.00
               - snps,dwmac-4.10a
               - snps,dwmac-4.20a
Signature · 7 lines
2.39.2


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#4 lore raw

PATCH v2 3/12 dt-bindings: net: qcom,ethqos: Convert bindings to yaml

In reply to Andrew Halaney

From: Bhupesh Sharma <[email protected]>

Convert Qualcomm ETHQOS Ethernet devicetree binding to YAML. In doing so add a new property for iommus since newer platforms support using one, and without such make dtbs_check fails on them.

While at it, also update the MAINTAINERS file to point to the yaml version of the bindings.

[halaney: Remove duplicated properties, add MAINTAINERS and iommus]

---

Changes since v1:
* Drop redundant wording in binding description (Krzysztof)
* Document iommus addition explicitly in commit message (Krzysztof)

 .../devicetree/bindings/net/qcom,ethqos.txt   |  66 -----------
 .../devicetree/bindings/net/qcom,ethqos.yaml  | 110 ++++++++++++++++++
 MAINTAINERS                                   |   2 +-
 3 files changed, 111 insertions(+), 67 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/net/qcom,ethqos.txt
 create mode 100644 Documentation/devicetree/bindings/net/qcom,ethqos.yaml
Documentation/devicetree/bindings/net/qcom,ethqos.txt deleted +0 -66
deleted file mode 100644
index 1f5746849a71..000000000000
@@ -1,66 +0,0 @@
-Qualcomm Ethernet ETHQOS device
-
-This documents dwmmac based ethernet device which supports Gigabit
-ethernet for version v2.3.0 onwards.
-
-This device has following properties:
-
-Required properties:
-
-- compatible: Should be one of:
-		"qcom,qcs404-ethqos"
-		"qcom,sm8150-ethqos"
-
-- reg: Address and length of the register set for the device
-
-- reg-names: Should contain register names "stmmaceth", "rgmii"
-
-- clocks: Should contain phandle to clocks
-
-- clock-names: Should contain clock names "stmmaceth", "pclk",
-		"ptp_ref", "rgmii"
-
-- interrupts: Should contain phandle to interrupts
-
-- interrupt-names: Should contain interrupt names "macirq", "eth_lpi"
-
-Rest of the properties are defined in stmmac.txt file in same directory
-
-
-Example:
-
-ethernet: ethernet@7a80000 {
-	compatible = "qcom,qcs404-ethqos";
-	reg = <0x07a80000 0x10000>,
-		<0x07a96000 0x100>;
-	reg-names = "stmmaceth", "rgmii";
-	clock-names = "stmmaceth", "pclk", "ptp_ref", "rgmii";
-	clocks = <&gcc GCC_ETH_AXI_CLK>,
-		<&gcc GCC_ETH_SLAVE_AHB_CLK>,
-		<&gcc GCC_ETH_PTP_CLK>,
-		<&gcc GCC_ETH_RGMII_CLK>;
-	interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
-			<GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
-	interrupt-names = "macirq", "eth_lpi";
-	snps,reset-gpio = <&tlmm 60 GPIO_ACTIVE_LOW>;
-	snps,reset-active-low;
-
-	snps,txpbl = <8>;
-	snps,rxpbl = <2>;
-	snps,aal;
-	snps,tso;
-
-	phy-handle = <&phy1>;
-	phy-mode = "rgmii";
-
-	mdio {
-		#address-cells = <0x1>;
-		#size-cells = <0x0>;
-		compatible = "snps,dwmac-mdio";
-		phy1: phy@4 {
-			device_type = "ethernet-phy";
-			reg = <0x4>;
-		};
-	};
-
-};
Documentation/devicetree/bindings/net/qcom,ethqos.yaml new file +110 -0

110 lines not on this page · raw message

MAINTAINERS +1 -1
index 30ca644d704f..a58b1d1d0626 100644
@@ -17282,7 +17282,7 @@ M:	Vinod Koul <[email protected]>
 R:	Bhupesh Sharma <[email protected]>
 L:	[email protected]
 S:	Maintained
-F:	Documentation/devicetree/bindings/net/qcom,ethqos.txt
+F:	Documentation/devicetree/bindings/net/qcom,ethqos.yaml
 F:	drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c
 
 QUALCOMM FASTRPC DRIVER
Signature · 1 line
2.39.2
Reviewed-by on v2 3/12
#5 lore raw

Re: [PATCH net-next v2 03/12] dt-bindings: net: qcom,ethqos: Convert bindings to yaml

Quoted 6 lines · Andrew Halaney

From: Bhupesh Sharma <[email protected]>

Convert Qualcomm ETHQOS Ethernet devicetree binding to YAML. In doing so add a new property for iommus since newer platforms support using one, and without such make dtbs_check fails on them.

Quoted 8 lines

While at it, also update the MAINTAINERS file to point to the yaml version of the bindings.

[halaney: Remove duplicated properties, add MAINTAINERS and iommus]

---

Best regards,
Krzysztof

#6 lore raw

PATCH v2 4/12 dt-bindings: net: qcom,ethqos: Add Qualcomm sc8280xp compatibles

In reply to Andrew Halaney

The sc8280xp has a new version of the ETHQOS hardware in it, EMAC v3. Add a compatible for this.

---

Changes since v1:
* Alphabetical sorting (Krzysztof)

 Documentation/devicetree/bindings/net/qcom,ethqos.yaml | 1 +
 Documentation/devicetree/bindings/net/snps,dwmac.yaml  | 3 +++
 2 files changed, 4 insertions(+)
Documentation/devicetree/bindings/net/qcom,ethqos.yaml +1 -0
index 88234a2010b1..c60248e17e5a 100644
@@ -21,6 +21,7 @@ properties:
     enum:
       - qcom,qcs404-ethqos
       - qcom,sm8150-ethqos
+      - qcom,sc8280xp-ethqos
 
   reg:
     maxItems: 2
Documentation/devicetree/bindings/net/snps,dwmac.yaml +3 -0
index 154955718246..126552febe7e 100644
@@ -66,6 +66,7 @@ properties:
         - loongson,ls2k-dwmac
         - loongson,ls7a-dwmac
         - qcom,qcs404-ethqos
+        - qcom,sc8280xp-ethqos
         - qcom,sm8150-ethqos
         - renesas,r9a06g032-gmac
         - renesas,rzn1-gmac
@@ -574,6 +575,7 @@ allOf:
               - ingenic,x1600-mac
               - ingenic,x1830-mac
               - ingenic,x2000-mac
+              - qcom,sc8280xp-ethqos
               - snps,dwmac-3.50a
               - snps,dwmac-4.10a
               - snps,dwmac-4.20a
@@ -628,6 +630,7 @@ allOf:
               - ingenic,x1830-mac
               - ingenic,x2000-mac
               - qcom,qcs404-ethqos
+              - qcom,sc8280xp-ethqos
               - qcom,sm8150-ethqos
               - snps,dwmac-4.00
               - snps,dwmac-4.10a
Signature · 7 lines
2.39.2


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#7 lore raw

Re: [PATCH net-next v2 04/12] dt-bindings: net: qcom,ethqos: Add Qualcomm sc8280xp compatibles

Quoted 18 lines · Andrew Halaney

The sc8280xp has a new version of the ETHQOS hardware in it, EMAC v3. Add a compatible for this.

---

Changes since v1:
* Alphabetical sorting (Krzysztof)

 Documentation/devicetree/bindings/net/qcom,ethqos.yaml | 1 +
 Documentation/devicetree/bindings/net/snps,dwmac.yaml  | 3 +++
 2 files changed, 4 insertions(+)
Documentation/devicetree/bindings/net/qcom,ethqos.yaml +0 -0
index 88234a2010b1..c60248e17e5a 100644

Documentation/devicetree/bindings/net/qcom,ethqos.yaml properties: · line 24

Quoted 4 lines
Documentation/devicetree/bindings/net/qcom,ethqos.yaml +1 -0
@@ -21,6 +21,7 @@ properties:
     enum:
       - qcom,qcs404-ethqos
       - qcom,sm8150-ethqos
+      - qcom,sc8280xp-ethqos

This still needs sort.

Best regards,
Krzysztof

#8 lore raw

PATCH v2 5/12 clk: qcom: gcc-sc8280xp: Add EMAC GDSCs

In reply to Andrew Halaney

Add the EMAC GDSCs to allow the EMAC hardware to be enabled.

---

I'm still unsure if Bjorn wants to take this patch or net-dev, and how I am supposed to indicate such other than commenting here (per Stephen's
comment on v1): https://lore.kernel.org/netdev/[email protected]/#t

Changes since v1:
* Add Stephen's Acked-by
* Explicitly tested on x13s laptop with no noticeable side effect (Konrad)

 drivers/clk/qcom/gcc-sc8280xp.c               | 18 ++++++++++++++++++
 include/dt-bindings/clock/qcom,gcc-sc8280xp.h |  2 ++
 2 files changed, 20 insertions(+)
drivers/clk/qcom/gcc-sc8280xp.c +18 -0
index b3198784e1c3..04a99dbaa57e 100644
@@ -6873,6 +6873,22 @@ static struct gdsc usb30_sec_gdsc = {
 	.pwrsts = PWRSTS_RET_ON,
 };
 
+static struct gdsc emac_0_gdsc = {
+	.gdscr = 0xaa004,
+	.pd = {
+		.name = "emac_0_gdsc",
+	},
+	.pwrsts = PWRSTS_OFF_ON,
+};
+
+static struct gdsc emac_1_gdsc = {
+	.gdscr = 0xba004,
+	.pd = {
+		.name = "emac_1_gdsc",
+	},
+	.pwrsts = PWRSTS_OFF_ON,
+};
+
 static struct clk_regmap *gcc_sc8280xp_clocks[] = {
 	[GCC_AGGRE_NOC_PCIE0_TUNNEL_AXI_CLK] = &gcc_aggre_noc_pcie0_tunnel_axi_clk.clkr,
 	[GCC_AGGRE_NOC_PCIE1_TUNNEL_AXI_CLK] = &gcc_aggre_noc_pcie1_tunnel_axi_clk.clkr,
@@ -7351,6 +7367,8 @@ static struct gdsc *gcc_sc8280xp_gdscs[] = {
 	[USB30_MP_GDSC] = &usb30_mp_gdsc,
 	[USB30_PRIM_GDSC] = &usb30_prim_gdsc,
 	[USB30_SEC_GDSC] = &usb30_sec_gdsc,
+	[EMAC_0_GDSC] = &emac_0_gdsc,
+	[EMAC_1_GDSC] = &emac_1_gdsc,
 };
 
 static const struct clk_rcg_dfs_data gcc_dfs_clocks[] = {
include/dt-bindings/clock/qcom,gcc-sc8280xp.h +2 -0
index cb2fb638825c..721105ea4fad 100644
@@ -492,5 +492,7 @@
 #define USB30_MP_GDSC					9
 #define USB30_PRIM_GDSC					10
 #define USB30_SEC_GDSC					11
+#define EMAC_0_GDSC					12
+#define EMAC_1_GDSC					13
 
 #endif
Signature · 7 lines
2.39.2


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Reviewed-by on v2 5/12
#9 lore raw

Re: [PATCH net-next v2 05/12] clk: qcom: gcc-sc8280xp: Add EMAC GDSCs

Quoted 5 lines · Andrew Halaney

Add the EMAC GDSCs to allow the EMAC hardware to be enabled.

---

Konrad

Quoted 61 lines

I'm still unsure if Bjorn wants to take this patch or net-dev, and how I am supposed to indicate such other than commenting here (per Stephen's
comment on v1): https://lore.kernel.org/netdev/[email protected]/#t

Changes since v1:
* Add Stephen's Acked-by
* Explicitly tested on x13s laptop with no noticeable side effect (Konrad)

 drivers/clk/qcom/gcc-sc8280xp.c               | 18 ++++++++++++++++++
 include/dt-bindings/clock/qcom,gcc-sc8280xp.h |  2 ++
 2 files changed, 20 insertions(+)
drivers/clk/qcom/gcc-sc8280xp.c +18 -0
index b3198784e1c3..04a99dbaa57e 100644
@@ -6873,6 +6873,22 @@ static struct gdsc usb30_sec_gdsc = {
 	.pwrsts = PWRSTS_RET_ON,
 };
 
+static struct gdsc emac_0_gdsc = {
+	.gdscr = 0xaa004,
+	.pd = {
+		.name = "emac_0_gdsc",
+	},
+	.pwrsts = PWRSTS_OFF_ON,
+};
+
+static struct gdsc emac_1_gdsc = {
+	.gdscr = 0xba004,
+	.pd = {
+		.name = "emac_1_gdsc",
+	},
+	.pwrsts = PWRSTS_OFF_ON,
+};
+
 static struct clk_regmap *gcc_sc8280xp_clocks[] = {
 	[GCC_AGGRE_NOC_PCIE0_TUNNEL_AXI_CLK] = &gcc_aggre_noc_pcie0_tunnel_axi_clk.clkr,
 	[GCC_AGGRE_NOC_PCIE1_TUNNEL_AXI_CLK] = &gcc_aggre_noc_pcie1_tunnel_axi_clk.clkr,
@@ -7351,6 +7367,8 @@ static struct gdsc *gcc_sc8280xp_gdscs[] = {
 	[USB30_MP_GDSC] = &usb30_mp_gdsc,
 	[USB30_PRIM_GDSC] = &usb30_prim_gdsc,
 	[USB30_SEC_GDSC] = &usb30_sec_gdsc,
+	[EMAC_0_GDSC] = &emac_0_gdsc,
+	[EMAC_1_GDSC] = &emac_1_gdsc,
 };
 
 static const struct clk_rcg_dfs_data gcc_dfs_clocks[] = {
include/dt-bindings/clock/qcom,gcc-sc8280xp.h +2 -0
index cb2fb638825c..721105ea4fad 100644
@@ -492,5 +492,7 @@
 #define USB30_MP_GDSC					9
 #define USB30_PRIM_GDSC					10
 #define USB30_SEC_GDSC					11
+#define EMAC_0_GDSC					12
+#define EMAC_1_GDSC					13
 
 #endif
#10 lore raw

PATCH v2 6/12 arm64: dts: qcom: sc8280xp: Add ethernet nodes

In reply to Andrew Halaney

This platform has 2 MACs integrated in it, go ahead and describe them.

---

Changes since v1:
* None

 arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 53 ++++++++++++++++++++++++++
 1 file changed, 53 insertions(+)
arch/arm64/boot/dts/qcom/sc8280xp.dtsi +53 -0
index 0d02599d8867..a63e8e81a8c4 100644
@@ -761,6 +761,59 @@ soc: soc@0 {
 		ranges = <0 0 0 0 0x10 0>;
 		dma-ranges = <0 0 0 0 0x10 0>;
 
+		ethernet0: ethernet@20000 {
+			compatible = "qcom,sc8280xp-ethqos";
+			reg = <0x0 0x00020000 0x0 0x10000>,
+				<0x0 0x00036000 0x0 0x100>;
+			reg-names = "stmmaceth", "rgmii";
+
+			clocks = <&gcc GCC_EMAC0_AXI_CLK>,
+				<&gcc GCC_EMAC0_SLV_AHB_CLK>,
+				<&gcc GCC_EMAC0_PTP_CLK>,
+				<&gcc GCC_EMAC0_RGMII_CLK>;
+			clock-names = "stmmaceth", "pclk", "ptp_ref", "rgmii";
+
+			interrupts = <GIC_SPI 946 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 936 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq", "eth_lpi";
+			iommus = <&apps_smmu 0x4c0 0xf>;
+			power-domains = <&gcc EMAC_0_GDSC>;
+
+			snps,tso;
+			snps,pbl = <32>;
+			rx-fifo-depth = <4096>;
+			tx-fifo-depth = <4096>;
+
+			status = "disabled";
+		};
+
+		ethernet1: ethernet@23000000 {
+			compatible = "qcom,sc8280xp-ethqos";
+			reg = <0x0 0x23000000 0x0 0x10000>,
+				<0x0 0x23016000 0x0 0x100>;
+			reg-names = "stmmaceth", "rgmii";
+
+			clocks = <&gcc GCC_EMAC1_AXI_CLK>,
+				<&gcc GCC_EMAC1_SLV_AHB_CLK>,
+				<&gcc GCC_EMAC1_PTP_CLK>,
+				<&gcc GCC_EMAC1_RGMII_CLK>;
+			clock-names = "stmmaceth", "pclk", "ptp_ref", "rgmii";
+
+			interrupts = <GIC_SPI 929 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 919 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq", "eth_lpi";
+
+			iommus = <&apps_smmu 0x40 0xf>;
+			power-domains = <&gcc EMAC_1_GDSC>;
+
+			snps,tso;
+			snps,pbl = <32>;
+			rx-fifo-depth = <4096>;
+			tx-fifo-depth = <4096>;
+
+			status = "disabled";
+		};
+
 		gcc: clock-controller@100000 {
 			compatible = "qcom,gcc-sc8280xp";
 			reg = <0x0 0x00100000 0x0 0x1f0000>;
Signature · 7 lines
2.39.2


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#11 lore raw

Re: [PATCH net-next v2 06/12] arm64: dts: qcom: sc8280xp: Add ethernet nodes

Quoted 16 lines · Andrew Halaney

This platform has 2 MACs integrated in it, go ahead and describe them.

---

Changes since v1:
* None

 arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 53 ++++++++++++++++++++++++++
 1 file changed, 53 insertions(+)
arch/arm64/boot/dts/qcom/sc8280xp.dtsi +0 -0
index 0d02599d8867..a63e8e81a8c4 100644

arch/arm64/boot/dts/qcom/sc8280xp.dtsi soc: soc@0 { · line 767

Quoted 7 lines
arch/arm64/boot/dts/qcom/sc8280xp.dtsi +4 -0
@@ -761,6 +761,59 @@ soc: soc@0 {
 		ranges = <0 0 0 0 0x10 0>;
 		dma-ranges = <0 0 0 0 0x10 0>;
 
+		ethernet0: ethernet@20000 {
+			compatible = "qcom,sc8280xp-ethqos";
+			reg = <0x0 0x00020000 0x0 0x10000>,
+				<0x0 0x00036000 0x0 0x100>;

Please correct the indentation here.

arch/arm64/boot/dts/qcom/sc8280xp.dtsi soc: soc@0 { · line 773

Quoted 6 lines
arch/arm64/boot/dts/qcom/sc8280xp.dtsi +6 -0
+			reg-names = "stmmaceth", "rgmii";
+
+			clocks = <&gcc GCC_EMAC0_AXI_CLK>,
+				<&gcc GCC_EMAC0_SLV_AHB_CLK>,
+				<&gcc GCC_EMAC0_PTP_CLK>,
+				<&gcc GCC_EMAC0_RGMII_CLK>;

Please correct the indentation here.

arch/arm64/boot/dts/qcom/sc8280xp.dtsi soc: soc@0 { · line 774

Quoted 1 line
arch/arm64/boot/dts/qcom/sc8280xp.dtsi +1 -0
+			clock-names = "stmmaceth", "pclk", "ptp_ref", "rgmii";

Please turn this into a vertical list.

arch/arm64/boot/dts/qcom/sc8280xp.dtsi soc: soc@0 { · line 777

Quoted 3 lines
arch/arm64/boot/dts/qcom/sc8280xp.dtsi +3 -0
+
+			interrupts = <GIC_SPI 946 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 936 IRQ_TYPE_LEVEL_HIGH>;

Please correct the indentation here.

Same for the other node.

Konrad

Quoted 42 lines
arch/arm64/boot/dts/qcom/sc8280xp.dtsi +39 -0
+			interrupt-names = "macirq", "eth_lpi";
+			iommus = <&apps_smmu 0x4c0 0xf>;
+			power-domains = <&gcc EMAC_0_GDSC>;
+
+			snps,tso;
+			snps,pbl = <32>;
+			rx-fifo-depth = <4096>;
+			tx-fifo-depth = <4096>;
+
+			status = "disabled";
+		};
+
+		ethernet1: ethernet@23000000 {
+			compatible = "qcom,sc8280xp-ethqos";
+			reg = <0x0 0x23000000 0x0 0x10000>,
+				<0x0 0x23016000 0x0 0x100>;
+			reg-names = "stmmaceth", "rgmii";
+
+			clocks = <&gcc GCC_EMAC1_AXI_CLK>,
+				<&gcc GCC_EMAC1_SLV_AHB_CLK>,
+				<&gcc GCC_EMAC1_PTP_CLK>,
+				<&gcc GCC_EMAC1_RGMII_CLK>;
+			clock-names = "stmmaceth", "pclk", "ptp_ref", "rgmii";
+
+			interrupts = <GIC_SPI 929 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 919 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq", "eth_lpi";
+
+			iommus = <&apps_smmu 0x40 0xf>;
+			power-domains = <&gcc EMAC_1_GDSC>;
+
+			snps,tso;
+			snps,pbl = <32>;
+			rx-fifo-depth = <4096>;
+			tx-fifo-depth = <4096>;
+
+			status = "disabled";
+		};
+
 		gcc: clock-controller@100000 {
 			compatible = "qcom,gcc-sc8280xp";
 			reg = <0x0 0x00100000 0x0 0x1f0000>;
#12 lore raw

PATCH v2 7/12 arm64: dts: qcom: sa8540p-ride: Add ethernet nodes

In reply to Andrew Halaney

Enable both the MACs found on the board.

ethernet0 and ethernet1 both ultimately go to a series of on board switches which aren't managed by this processor.

ethernet0 is connected to a Marvell 88EA1512 phy via RGMII. That goes to the series of switches via SGMII on the "media" side of the phy. RGMII_SGMII mode is enabled via devicetree register descriptions. The switch on the "media" side has auto-negotiation disabled, so configuration from userspace similar to:

ethtool -s eth0 autoneg off speed 1000 duplex full

is necessary to get traffic flowing on that interface.

ethernet1 is in a mac2mac/fixed-link configuration going to the same series of switches directly via RGMII.

---

Changes since v1:
* None

 arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 181 ++++++++++++++++++++++
 1 file changed, 181 insertions(+)
arch/arm64/boot/dts/qcom/sa8540p-ride.dts +181 -0
index 8b7555f22528..b874f3909382 100644
@@ -28,6 +28,65 @@ aliases {
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	mtl_rx_setup: rx-queues-config {
+		snps,rx-queues-to-use = <1>;
+		snps,rx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+			snps,map-to-dma-channel = <0x0>;
+			snps,route-up;
+			snps,priority = <0x1>;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+			snps,map-to-dma-channel = <0x1>;
+			snps,route-ptp;
+		};
+
+		queue2 {
+			snps,avb-algorithm;
+			snps,map-to-dma-channel = <0x2>;
+			snps,route-avcp;
+		};
+
+		queue3 {
+			snps,avb-algorithm;
+			snps,map-to-dma-channel = <0x3>;
+			snps,priority = <0xc>;
+		};
+	};
+
+	mtl_tx_setup: tx-queues-config {
+		snps,tx-queues-to-use = <1>;
+		snps,tx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+		};
+
+		queue2 {
+			snps,avb-algorithm;
+			snps,send_slope = <0x1000>;
+			snps,idle_slope = <0x1000>;
+			snps,high_credit = <0x3e800>;
+			snps,low_credit = <0xffc18000>;
+		};
+
+		queue3 {
+			snps,avb-algorithm;
+			snps,send_slope = <0x1000>;
+			snps,idle_slope = <0x1000>;
+			snps,high_credit = <0x3e800>;
+			snps,low_credit = <0xffc18000>;
+		};
+	};
 };
 
 &apps_rsc {
@@ -151,6 +210,68 @@ vreg_l8g: ldo8 {
 	};
 };
 
+&ethernet0 {
+	snps,mtl-rx-config = <&mtl_rx_setup>;
+	snps,mtl-tx-config = <&mtl_tx_setup>;
+
+	max-speed = <1000>;
+	phy-handle = <&rgmii_phy>;
+	phy-mode = "rgmii-txid";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&ethernet0_default>;
+
+	status = "okay";
+
+	mdio {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		compatible = "snps,dwmac-mdio";
+
+		/* Marvell 88EA1512 */
+		rgmii_phy: phy@8 {
+			reg = <0x8>;
+
+			interrupt-parent = <&tlmm>;
+			interrupts-extended = <&tlmm 127 IRQ_TYPE_EDGE_FALLING>;
+
+			reset-gpios = <&pmm8540c_gpios 1 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <11000>;
+			reset-deassert-us = <70000>;
+
+			device_type = "ethernet-phy";
+
+			/* Set to RGMII_SGMII mode and soft reset. Turn off auto-negotiation
+			 * from userspace to talk to the switch on the SGMII side of things
+			 */
+			marvell,reg-init =
+				/* Set MODE[2:0] to RGMII_SGMII */
+				<0x12 0x14 0xfff8 0x4>,
+				/* Soft reset required after changing MODE[2:0] */
+				<0x12 0x14 0x7fff 0x8000>;
+		};
+	};
+};
+
+&ethernet1 {
+	snps,mtl-rx-config = <&mtl_rx_setup>;
+	snps,mtl-tx-config = <&mtl_tx_setup>;
+
+	max-speed = <1000>;
+	phy-mode = "rgmii-txid";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&ethernet1_default>;
+
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
 &i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_default>;
@@ -316,6 +437,66 @@ &xo_board_clk {
 /* PINCTRL */
 
 &tlmm {
+	ethernet0_default: ethernet0-default-state {
+		mdc-pins {
+			pins = "gpio175";
+			function = "rgmii_0";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		mdio-pins {
+			pins = "gpio176";
+			function = "rgmii_0";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		rgmii-tx-pins {
+			pins = "gpio183", "gpio184", "gpio185", "gpio186", "gpio187", "gpio188";
+			function = "rgmii_0";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		rgmii-rx-pins {
+			pins = "gpio177", "gpio178", "gpio179", "gpio180", "gpio181", "gpio182";
+			function = "rgmii_0";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	ethernet1_default: ethernet1-default-state {
+		mdc-pins {
+			pins = "gpio97";
+			function = "rgmii_1";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		mdio-pins {
+			pins = "gpio98";
+			function = "rgmii_1";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		rgmii-tx-pins {
+			pins = "gpio105", "gpio106", "gpio107", "gpio108", "gpio109", "gpio110";
+			function = "rgmii_1";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		rgmii-rx-pins {
+			pins = "gpio99", "gpio100", "gpio101", "gpio102", "gpio103", "gpio104";
+			function = "rgmii_1";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
 	i2c0_default: i2c0-default-state {
 		/* To USB7002T-I/KDXVA0 USB hub (SIP1 only) */
 		pins = "gpio135", "gpio136";
Signature · 7 lines
2.39.2


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#13 lore raw

PATCH v2 8/12 net: stmmac: Remove unnecessary if statement brackets

In reply to Andrew Halaney

The brackets are unnecessary, remove them to match the coding style used in the kernel.

---

Changes since v1:
* This patch is split from the next patch since it is a logically different change (Andrew Lunn)

 drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c +1 -2
index 21aaa2730ac8..6807c4c1a0a2 100644
@@ -281,9 +281,8 @@ static int stmmac_mdio_read_c22(struct mii_bus *bus, int phyaddr, int phyreg)
 	value |= (phyreg << priv->hw->mii.reg_shift) & priv->hw->mii.reg_mask;
 	value |= (priv->clk_csr << priv->hw->mii.clk_csr_shift)
 		& priv->hw->mii.clk_csr_mask;
-	if (priv->plat->has_gmac4) {
+	if (priv->plat->has_gmac4)
 		value |= MII_GMAC4_READ;
-	}
 
 	data = stmmac_mdio_read(priv, data, value);
 
Signature · 7 lines
2.39.2


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#14 lore raw

PATCH v2 9/12 net: stmmac: Add EMAC3 variant of dwmac4

In reply to Andrew Halaney

From: Brian Masney <[email protected]>

EMAC3 is a Qualcomm variant of dwmac4 that functions the same, but has a different address space layout for MTL and DMA registers. This makes the patch a bit more complicated than we would like so let's explain why the current approach was used.

The different address ranges between the two variants can be represented with 7 different sets of #ifdefs like the following:

    #if IS_ENABLED(CONFIG_DWMAC_QCOM_VER3)
    # define MTL_CHAN_BASE_ADDR             0x00008000
    # define MTL_CHAN_BASE_OFFSET           0x1000
    #else
    # define MTL_CHAN_BASE_ADDR             0x00000d00
    # define MTL_CHAN_BASE_OFFSET           0x40
    #endif

This won't be acceptable for upstream inclusion since it would be nice to enable both variants simultaneously without recompiling.

The next approach that was checked was to have a function pointer embedded inside a structure that does the appropriate conversion based on the variant that's in use. However, some of the function definitions are like the following:

void emac3_set_rx_ring_len(void __iomem *ioaddr, u32 len, u32 chan)

We can't do a container_of() with an __iomem address. Changing these functions to pass in an extra regular structure had a cascading effect across the different variants, and the change was quickly becoming large. It would also be hard to test and review.

So the approach that was decided to go with here is to take the existing dwmac4_XXX callbacks, rename it to do_XXX, and do the following:

    static void do_XXX(..., int addr_offset)
    {
       // Code from existing dwmac4 implementation.
    }

    static inline void emac3_XXX(...)
    {
        do_XXX(..., EMAC3_ADDR_OFFSET(...));
    }

    static inline void dwmac4_XXX(...)
    {
        do_XXX(..., DWMAC4_ADDR_OFFSET(...));
    }

Prior to the introduction of this patch, dwmac4_dma_init_channel() and dwmac410_dma_init_channel() already had the problem of copy and paste with trivial changes made.

While changes are being made here, this patch also fixes a bad comment that was in dwmac4_config_cbs (s/high/low).

---

Changes since v1:
* Clean up if statement bracket in its own (prior) patch (Andrew Lunn)
* Remove unnecessary static inlines (Jakub)
* Don't exceed 6 function arguments (use a struct instead) (Jakub)

I think despite Russell's comments Jakub's insights on readability with respect to function arguments / structure usage / poor man's **kwargs are still valid for this particular context. Hopefully this is a bit more appealing looking. There was only one function that needed this, do_config_cbs, otherwise they were all at <= 6 function args.

 drivers/net/ethernet/stmicro/stmmac/dwmac4.h  |  32 +-
 .../net/ethernet/stmicro/stmmac/dwmac4_core.c | 235 ++++++++++--
 .../net/ethernet/stmicro/stmmac/dwmac4_dma.c  | 334 ++++++++++++++----
 .../net/ethernet/stmicro/stmmac/dwmac4_dma.h  |  38 ++
 .../net/ethernet/stmicro/stmmac/dwmac4_lib.c  | 144 ++++++--
 drivers/net/ethernet/stmicro/stmmac/hwif.c    |  29 +-
 drivers/net/ethernet/stmicro/stmmac/hwif.h    |   2 +
 .../ethernet/stmicro/stmmac/stmmac_ethtool.c  |   6 +-
 .../net/ethernet/stmicro/stmmac/stmmac_main.c |  17 +-
 .../net/ethernet/stmicro/stmmac/stmmac_mdio.c |   8 +-
 .../net/ethernet/stmicro/stmmac/stmmac_ptp.c  |   4 +-
 include/linux/stmmac.h                        |   1 +
 12 files changed, 707 insertions(+), 143 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac4.h +31 -1
index ccd49346d3b3..56355d65fa4b 100644
@@ -333,7 +333,16 @@ enum power_event {
 #define MTL_RXQ_DMA_MAP1		0x00000c34 /* queue 4 to 7 */
 #define MTL_RXQ_DMA_QXMDMACH_MASK(x)	(0xf << 8 * (x))
 #define MTL_RXQ_DMA_QXMDMACH(chan, q)	((chan) << (8 * (q)))
-
+#define EMAC3_MTL_CHAN_BASE_ADDR		0x00008000
+#define EMAC3_MTL_CHAN_BASE_OFFSET		0x1000
+#define EMAC3_MTL_CHANX_BASE_ADDR(x)		(EMAC3_MTL_CHAN_BASE_ADDR + \
+					((x) * EMAC3_MTL_CHAN_BASE_OFFSET))
+
+#define EMAC3_MTL_CHAN_TX_OP_MODE(x)		EMAC3_MTL_CHANX_BASE_ADDR(x)
+#define EMAC3_MTL_CHAN_TX_DEBUG(x)		(EMAC3_MTL_CHANX_BASE_ADDR(x) + 0x8)
+#define EMAC3_MTL_CHAN_INT_CTRL(x)		(EMAC3_MTL_CHANX_BASE_ADDR(x) + 0x2c)
+#define EMAC3_MTL_CHAN_RX_OP_MODE(x)		(EMAC3_MTL_CHANX_BASE_ADDR(x) + 0x30)
+#define EMAC3_MTL_CHAN_RX_DEBUG(x)		(EMAC3_MTL_CHANX_BASE_ADDR(x) + 0x38)
 #define MTL_CHAN_BASE_ADDR		0x00000d00
 #define MTL_CHAN_BASE_OFFSET		0x40
 #define MTL_CHANX_BASE_ADDR(x)		(MTL_CHAN_BASE_ADDR + \
@@ -386,6 +395,10 @@ enum power_event {
 #define MTL_OP_MODE_RTC_128		(3 << MTL_OP_MODE_RTC_SHIFT)
 
 /* MTL ETS Control register */
+#define EMAC3_MTL_ETS_CTRL_BASE_ADDR		0x00008010
+#define EMAC3_MTL_ETS_CTRL_BASE_OFFSET	0x1000
+#define EMAC3_MTL_ETSX_CTRL_BASE_ADDR(x)	(EMAC3_MTL_ETS_CTRL_BASE_ADDR + \
+					((x) * EMAC3_MTL_ETS_CTRL_BASE_OFFSET))
 #define MTL_ETS_CTRL_BASE_ADDR		0x00000d10
 #define MTL_ETS_CTRL_BASE_OFFSET	0x40
 #define MTL_ETSX_CTRL_BASE_ADDR(x)	(MTL_ETS_CTRL_BASE_ADDR + \
@@ -395,6 +408,10 @@ enum power_event {
 #define MTL_ETS_CTRL_AVALG		BIT(2)
 
 /* MTL Queue Quantum Weight */
+#define EMAC3_MTL_TXQ_WEIGHT_BASE_ADDR	0x00008018
+#define EMAC3_MTL_TXQ_WEIGHT_BASE_OFFSET	0x1000
+#define EMAC3_MTL_TXQX_WEIGHT_BASE_ADDR(x)	(EMAC3_MTL_TXQ_WEIGHT_BASE_ADDR + \
+					((x) * EMAC3_MTL_TXQ_WEIGHT_BASE_OFFSET))
 #define MTL_TXQ_WEIGHT_BASE_ADDR	0x00000d18
 #define MTL_TXQ_WEIGHT_BASE_OFFSET	0x40
 #define MTL_TXQX_WEIGHT_BASE_ADDR(x)	(MTL_TXQ_WEIGHT_BASE_ADDR + \
@@ -402,6 +419,11 @@ enum power_event {
 #define MTL_TXQ_WEIGHT_ISCQW_MASK	GENMASK(20, 0)
 
 /* MTL sendSlopeCredit register */
+
+#define EMAC3_MTL_SEND_SLP_CRED_BASE_ADDR	0x0000801c
+#define EMAC3_MTL_SEND_SLP_CRED_OFFSET	0x1000
+#define EMAC3_MTL_SEND_SLP_CREDX_BASE_ADDR(x)	(EMAC3_MTL_SEND_SLP_CRED_BASE_ADDR + \
+					((x) * EMAC3_MTL_SEND_SLP_CRED_OFFSET))
 #define MTL_SEND_SLP_CRED_BASE_ADDR	0x00000d1c
 #define MTL_SEND_SLP_CRED_OFFSET	0x40
 #define MTL_SEND_SLP_CREDX_BASE_ADDR(x)	(MTL_SEND_SLP_CRED_BASE_ADDR + \
@@ -410,6 +432,10 @@ enum power_event {
 #define MTL_SEND_SLP_CRED_SSC_MASK	GENMASK(13, 0)
 
 /* MTL hiCredit register */
+#define EMAC3_MTL_HIGH_CRED_BASE_ADDR		0x00008020
+#define EMAC3_MTL_HIGH_CRED_OFFSET		0x1000
+#define EMAC3_MTL_HIGH_CREDX_BASE_ADDR(x)	(EMAC3_MTL_HIGH_CRED_BASE_ADDR + \
+					((x) * EMAC3_MTL_HIGH_CRED_OFFSET))
 #define MTL_HIGH_CRED_BASE_ADDR		0x00000d20
 #define MTL_HIGH_CRED_OFFSET		0x40
 #define MTL_HIGH_CREDX_BASE_ADDR(x)	(MTL_HIGH_CRED_BASE_ADDR + \
@@ -418,6 +444,10 @@ enum power_event {
 #define MTL_HIGH_CRED_HC_MASK		GENMASK(28, 0)
 
 /* MTL loCredit register */
+#define EMAC3_MTL_LOW_CRED_BASE_ADDR		0x00008024
+#define EMAC3_MTL_LOW_CRED_OFFSET		0x1000
+#define EMAC3_MTL_LOW_CREDX_BASE_ADDR(x)	(EMAC3_MTL_LOW_CRED_BASE_ADDR + \
+					((x) * EMAC3_MTL_LOW_CRED_OFFSET))
 #define MTL_LOW_CRED_BASE_ADDR		0x00000d24
 #define MTL_LOW_CRED_OFFSET		0x40
 #define MTL_LOW_CREDX_BASE_ADDR(x)	(MTL_LOW_CRED_BASE_ADDR + \
drivers/net/ethernet/stmicro/stmmac/dwmac4_core.c +202 -33

320 lines not on this page · raw message

drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c +268 -66

476 lines not on this page · raw message

drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.h +38 -0
index 9321879b599c..c9899eefba6c 100644
@@ -93,8 +93,11 @@
 #define DMA_TBS_DEF_FTOS		(DMA_TBS_FTOS | DMA_TBS_FTOV)
 
 /* Following DMA defines are chanels oriented */
+#define EMAC3_DMA_CHAN_BASE_ADDR		0x00008100
+#define EMAC3_DMA_CHAN_BASE_OFFSET		0x1000
 #define DMA_CHAN_BASE_ADDR		0x00001100
 #define DMA_CHAN_BASE_OFFSET		0x80
+
 #define DMA_CHANX_BASE_ADDR(x)		(DMA_CHAN_BASE_ADDR + \
 					(x * DMA_CHAN_BASE_OFFSET))
 #define DMA_CHAN_REG_NUMBER		17
@@ -119,6 +122,29 @@
 #define DMA_CHAN_CUR_RX_BUF_ADDR(x)	(DMA_CHANX_BASE_ADDR(x) + 0x5c)
 #define DMA_CHAN_STATUS(x)		(DMA_CHANX_BASE_ADDR(x) + 0x60)
 
+#define EMAC3_DMA_CHANX_BASE_ADDR(x)		(EMAC3_DMA_CHAN_BASE_ADDR + \
+					((x) * EMAC3_DMA_CHAN_BASE_OFFSET))
+
+#define EMAC3_DMA_CHAN_CONTROL(x)		EMAC3_DMA_CHANX_BASE_ADDR(x)
+#define EMAC3_DMA_CHAN_TX_CONTROL(x)		(EMAC3_DMA_CHANX_BASE_ADDR(x) + 0x4)
+#define EMAC3_DMA_CHAN_RX_CONTROL(x)		(EMAC3_DMA_CHANX_BASE_ADDR(x) + 0x8)
+#define EMAC3_DMA_CHAN_TX_BASE_ADDR_HI(x)	(EMAC3_DMA_CHANX_BASE_ADDR(x) + 0x10)
+#define EMAC3_DMA_CHAN_TX_BASE_ADDR(x)	(EMAC3_DMA_CHANX_BASE_ADDR(x) + 0x14)
+#define EMAC3_DMA_CHAN_RX_BASE_ADDR_HI(x)	(EMAC3_DMA_CHANX_BASE_ADDR(x) + 0x18)
+#define EMAC3_DMA_CHAN_RX_BASE_ADDR(x)	(EMAC3_DMA_CHANX_BASE_ADDR(x) + 0x1c)
+#define EMAC3_DMA_CHAN_TX_END_ADDR(x)		(EMAC3_DMA_CHANX_BASE_ADDR(x) + 0x20)
+#define EMAC3_DMA_CHAN_RX_END_ADDR(x)		(EMAC3_DMA_CHANX_BASE_ADDR(x) + 0x28)
+#define EMAC3_DMA_CHAN_TX_RING_LEN(x)		(EMAC3_DMA_CHANX_BASE_ADDR(x) + 0x2c)
+#define EMAC3_DMA_CHAN_RX_RING_LEN(x)		(EMAC3_DMA_CHANX_BASE_ADDR(x) + 0x30)
+#define EMAC3_DMA_CHAN_INTR_ENA(x)		(EMAC3_DMA_CHANX_BASE_ADDR(x) + 0x34)
+#define EMAC3_DMA_CHAN_RX_WATCHDOG(x)		(EMAC3_DMA_CHANX_BASE_ADDR(x) + 0x38)
+#define EMAC3_DMA_CHAN_SLOT_CTRL_STATUS(x)	(EMAC3_DMA_CHANX_BASE_ADDR(x) + 0x3c)
+#define EMAC3_DMA_CHAN_CUR_TX_DESC(x)		(EMAC3_DMA_CHANX_BASE_ADDR(x) + 0x44)
+#define EMAC3_DMA_CHAN_CUR_RX_DESC(x)		(EMAC3_DMA_CHANX_BASE_ADDR(x) + 0x4c)
+#define EMAC3_DMA_CHAN_CUR_TX_BUF_ADDR(x)	(EMAC3_DMA_CHANX_BASE_ADDR(x) + 0x54)
+#define EMAC3_DMA_CHAN_CUR_RX_BUF_ADDR(x)	(EMAC3_DMA_CHANX_BASE_ADDR(x) + 0x5c)
+#define EMAC3_DMA_CHAN_STATUS(x)		(EMAC3_DMA_CHANX_BASE_ADDR(x) + 0x60)
+
 /* DMA Control X */
 #define DMA_CONTROL_SPH			BIT(24)
 #define DMA_CONTROL_MSS_MASK		GENMASK(13, 0)
@@ -220,19 +246,31 @@
 #define DMA_CHAN0_DBG_STAT_RPS_SHIFT	8
 
 int dwmac4_dma_reset(void __iomem *ioaddr);
+void emac3_enable_dma_irq(void __iomem *ioaddr, u32 chan, bool rx, bool tx);
 void dwmac4_enable_dma_irq(void __iomem *ioaddr, u32 chan, bool rx, bool tx);
 void dwmac410_enable_dma_irq(void __iomem *ioaddr, u32 chan, bool rx, bool tx);
+void emac3_disable_dma_irq(void __iomem *ioaddr, u32 chan, bool rx, bool tx);
 void dwmac4_disable_dma_irq(void __iomem *ioaddr, u32 chan, bool rx, bool tx);
 void dwmac410_disable_dma_irq(void __iomem *ioaddr, u32 chan, bool rx, bool tx);
+void emac3_dma_start_tx(void __iomem *ioaddr, u32 chan);
 void dwmac4_dma_start_tx(void __iomem *ioaddr, u32 chan);
+void emac3_dma_stop_tx(void __iomem *ioaddr, u32 chan);
 void dwmac4_dma_stop_tx(void __iomem *ioaddr, u32 chan);
+void emac3_dma_start_rx(void __iomem *ioaddr, u32 chan);
 void dwmac4_dma_start_rx(void __iomem *ioaddr, u32 chan);
+void emac3_dma_stop_rx(void __iomem *ioaddr, u32 chan);
 void dwmac4_dma_stop_rx(void __iomem *ioaddr, u32 chan);
+int emac3_dma_interrupt(void __iomem *ioaddr, struct stmmac_extra_stats *x,
+			u32 chan, u32 dir);
 int dwmac4_dma_interrupt(void __iomem *ioaddr,
 			 struct stmmac_extra_stats *x, u32 chan, u32 dir);
+void emac3_set_rx_ring_len(void __iomem *ioaddr, u32 len, u32 chan);
 void dwmac4_set_rx_ring_len(void __iomem *ioaddr, u32 len, u32 chan);
+void emac3_set_tx_ring_len(void __iomem *ioaddr, u32 len, u32 chan);
 void dwmac4_set_tx_ring_len(void __iomem *ioaddr, u32 len, u32 chan);
+void emac3_set_rx_tail_ptr(void __iomem *ioaddr, u32 tail_ptr, u32 chan);
 void dwmac4_set_rx_tail_ptr(void __iomem *ioaddr, u32 tail_ptr, u32 chan);
+void emac3_set_tx_tail_ptr(void __iomem *ioaddr, u32 tail_ptr, u32 chan);
 void dwmac4_set_tx_tail_ptr(void __iomem *ioaddr, u32 tail_ptr, u32 chan);
 
 #endif /* __DWMAC4_DMA_H__ */
drivers/net/ethernet/stmicro/stmmac/dwmac4_lib.c +121 -23

231 lines not on this page · raw message

drivers/net/ethernet/stmicro/stmmac/hwif.c +26 -3
index bb7114f970f8..7d8aa5e316cf 100644
@@ -91,6 +91,7 @@ static const struct stmmac_hwif_entry {
 	bool gmac;
 	bool gmac4;
 	bool xgmac;
+	bool emac3;
 	u32 min_id;
 	u32 dev_id;
 	const struct stmmac_regs_off regs;
@@ -251,6 +252,25 @@ static const struct stmmac_hwif_entry {
 		.mmc = &dwxgmac_mmc_ops,
 		.setup = dwxlgmac2_setup,
 		.quirks = stmmac_dwxlgmac_quirks,
+	}, {
+		.gmac = false,
+		.gmac4 = false,
+		.xgmac = false,
+		.emac3 = true,
+		.min_id = DWMAC_CORE_5_10,
+		.regs = {
+			.ptp_off = PTP_GMAC4_OFFSET,
+			.mmc_off = MMC_GMAC4_OFFSET,
+		},
+		.desc = &dwmac4_desc_ops,
+		.dma = &emac3_dma_ops,
+		.mac = &emac3_ops,
+		.hwtimestamp = &stmmac_ptp,
+		.mode = &dwmac4_ring_mode_ops,
+		.tc = &dwmac510_tc_ops,
+		.mmc = &dwmac_mmc_ops,
+		.setup = dwmac4_setup,
+		.quirks = NULL,
 	},
 };
 
@@ -259,6 +279,7 @@ int stmmac_hwif_init(struct stmmac_priv *priv)
 	bool needs_xgmac = priv->plat->has_xgmac;
 	bool needs_gmac4 = priv->plat->has_gmac4;
 	bool needs_gmac = priv->plat->has_gmac;
+	bool needs_emac3 = priv->plat->has_emac3;
 	const struct stmmac_hwif_entry *entry;
 	struct mac_device_info *mac;
 	bool needs_setup = true;
@@ -267,7 +288,7 @@ int stmmac_hwif_init(struct stmmac_priv *priv)
 
 	if (needs_gmac) {
 		id = stmmac_get_id(priv, GMAC_VERSION);
-	} else if (needs_gmac4 || needs_xgmac) {
+	} else if (needs_gmac4 || needs_xgmac || needs_emac3) {
 		id = stmmac_get_id(priv, GMAC4_VERSION);
 		if (needs_xgmac)
 			dev_id = stmmac_get_dev_id(priv, GMAC4_VERSION);
@@ -280,9 +301,9 @@ int stmmac_hwif_init(struct stmmac_priv *priv)
 
 	/* Lets assume some safe values first */
 	priv->ptpaddr = priv->ioaddr +
-		(needs_gmac4 ? PTP_GMAC4_OFFSET : PTP_GMAC3_X_OFFSET);
+		((needs_gmac4 || needs_emac3) ? PTP_GMAC4_OFFSET : PTP_GMAC3_X_OFFSET);
 	priv->mmcaddr = priv->ioaddr +
-		(needs_gmac4 ? MMC_GMAC4_OFFSET : MMC_GMAC3_X_OFFSET);
+		((needs_gmac4 || needs_emac3) ? MMC_GMAC4_OFFSET : MMC_GMAC3_X_OFFSET);
 
 	/* Check for HW specific setup first */
 	if (priv->plat->setup) {
@@ -305,6 +326,8 @@ int stmmac_hwif_init(struct stmmac_priv *priv)
 			continue;
 		if (needs_xgmac ^ entry->xgmac)
 			continue;
+		if (needs_emac3 ^ entry->emac3)
+			continue;
 		/* Use synopsys_id var because some setups can override this */
 		if (priv->synopsys_id < entry->min_id)
 			continue;
drivers/net/ethernet/stmicro/stmmac/hwif.h +2 -0
index 16a7421715cb..44d77ced27cc 100644
@@ -620,6 +620,8 @@ struct stmmac_regs_off {
 	u32 mmc_off;
 };
 
+extern const struct stmmac_ops emac3_ops;
+extern const struct stmmac_dma_ops emac3_dma_ops;
 extern const struct stmmac_ops dwmac100_ops;
 extern const struct stmmac_dma_ops dwmac100_dma_ops;
 extern const struct stmmac_ops dwmac1000_ops;
drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c +3 -3
index 35c8dd92d369..0f62e5f85b60 100644
@@ -286,7 +286,7 @@ static void stmmac_ethtool_getdrvinfo(struct net_device *dev,
 {
 	struct stmmac_priv *priv = netdev_priv(dev);
 
-	if (priv->plat->has_gmac || priv->plat->has_gmac4)
+	if (priv->plat->has_gmac || priv->plat->has_gmac4 || priv->plat->has_emac3)
 		strscpy(info->driver, GMAC_ETHTOOL_NAME, sizeof(info->driver));
 	else if (priv->plat->has_xgmac)
 		strscpy(info->driver, XGMAC_ETHTOOL_NAME, sizeof(info->driver));
@@ -442,7 +442,7 @@ static int stmmac_ethtool_get_regs_len(struct net_device *dev)
 
 	if (priv->plat->has_xgmac)
 		return XGMAC_REGSIZE * 4;
-	else if (priv->plat->has_gmac4)
+	else if (priv->plat->has_gmac4 || priv->plat->has_emac3)
 		return GMAC4_REG_SPACE_SIZE;
 	return REG_SPACE_SIZE;
 }
@@ -457,7 +457,7 @@ static void stmmac_ethtool_gregs(struct net_device *dev,
 	stmmac_dump_dma_regs(priv, priv->ioaddr, reg_space);
 
 	/* Copy DMA registers to where ethtool expects them */
-	if (priv->plat->has_gmac4) {
+	if (priv->plat->has_gmac4 || priv->plat->has_emac3) {
 		/* GMAC4 dumps its DMA registers at its DMA_CHAN_BASE_ADDR */
 		memcpy(&reg_space[ETHTOOL_DMA_OFFSET],
 		       &reg_space[GMAC4_DMA_CHAN_BASE_ADDR / 4],
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +9 -8
index 8f543c3ab5c5..d086fe811b67 100644
@@ -509,7 +509,8 @@ bool stmmac_eee_init(struct stmmac_priv *priv)
 					true);
 	}
 
-	if (priv->plat->has_gmac4 && priv->tx_lpi_timer <= STMMAC_ET_MAX) {
+	if ((priv->plat->has_gmac4 || priv->plat->has_emac3) &&
+	    priv->tx_lpi_timer <= STMMAC_ET_MAX) {
 		del_timer_sync(&priv->eee_ctrl_timer);
 		priv->tx_path_in_lpi_mode = false;
 		stmmac_lpi_entry_timer_config(priv, 1);
@@ -585,7 +586,7 @@ static void stmmac_get_rx_hwtstamp(struct stmmac_priv *priv, struct dma_desc *p,
 	if (!priv->hwts_rx_en)
 		return;
 	/* For GMAC4, the valid timestamp is from CTX next desc. */
-	if (priv->plat->has_gmac4 || priv->plat->has_xgmac)
+	if (priv->plat->has_gmac4 || priv->plat->has_emac3 || priv->plat->has_xgmac)
 		desc = np;
 
 	/* Check if timestamp is available */
@@ -833,7 +834,7 @@ static int stmmac_hwtstamp_get(struct net_device *dev, struct ifreq *ifr)
  */
 int stmmac_init_tstamp_counter(struct stmmac_priv *priv, u32 systime_flags)
 {
-	bool xmac = priv->plat->has_gmac4 || priv->plat->has_xgmac;
+	bool xmac = priv->plat->has_gmac4 || priv->plat->has_emac3 || priv->plat->has_xgmac;
 	struct timespec64 now;
 	u32 sec_inc = 0;
 	u64 temp = 0;
@@ -881,7 +882,7 @@ EXPORT_SYMBOL_GPL(stmmac_init_tstamp_counter);
  */
 static int stmmac_init_ptp(struct stmmac_priv *priv)
 {
-	bool xmac = priv->plat->has_gmac4 || priv->plat->has_xgmac;
+	bool xmac = priv->plat->has_gmac4 || priv->plat->has_emac3 || priv->plat->has_xgmac;
 	int ret;
 
 	if (priv->plat->ptp_clk_freq_config)
@@ -1207,7 +1208,7 @@ static int stmmac_phy_setup(struct stmmac_priv *priv)
 	if (!max_speed || max_speed >= 1000)
 		priv->phylink_config.mac_capabilities |= MAC_1000;
 
-	if (priv->plat->has_gmac4) {
+	if (priv->plat->has_gmac4 || priv->plat->has_emac3) {
 		if (!max_speed || max_speed >= 2500)
 			priv->phylink_config.mac_capabilities |= MAC_2500FD;
 	} else if (priv->plat->has_xgmac) {
@@ -4343,7 +4344,7 @@ static netdev_tx_t stmmac_xmit(struct sk_buff *skb, struct net_device *dev)
 	if (skb_is_gso(skb) && priv->tso) {
 		if (gso & (SKB_GSO_TCPV4 | SKB_GSO_TCPV6))
 			return stmmac_tso_xmit(skb, dev);
-		if (priv->plat->has_gmac4 && (gso & SKB_GSO_UDP_L4))
+		if ((priv->plat->has_gmac4 || priv->plat->has_emac3) && (gso & SKB_GSO_UDP_L4))
 			return stmmac_tso_xmit(skb, dev);
 	}
 
@@ -5721,7 +5722,7 @@ static void stmmac_common_interrupt(struct stmmac_priv *priv)
 	u32 queue;
 	bool xmac;
 
-	xmac = priv->plat->has_gmac4 || priv->plat->has_xgmac;
+	xmac = priv->plat->has_gmac4 || priv->plat->has_emac3 || priv->plat->has_xgmac;
 	queues_count = (rx_cnt > tx_cnt) ? rx_cnt : tx_cnt;
 
 	if (priv->irq_wake)
@@ -7165,7 +7166,7 @@ int stmmac_dvr_probe(struct device *device,
 
 	if ((priv->plat->tso_en) && (priv->dma_cap.tsoen)) {
 		ndev->hw_features |= NETIF_F_TSO | NETIF_F_TSO6;
-		if (priv->plat->has_gmac4)
+		if (priv->plat->has_gmac4 || priv->plat->has_emac3)
 			ndev->hw_features |= NETIF_F_GSO_UDP_L4;
 		priv->tso = true;
 		dev_info(priv->device, "TSO feature enabled\n");
drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c +4 -4
index 6807c4c1a0a2..9e3d8e1202bd 100644
@@ -281,7 +281,7 @@ static int stmmac_mdio_read_c22(struct mii_bus *bus, int phyaddr, int phyreg)
 	value |= (phyreg << priv->hw->mii.reg_shift) & priv->hw->mii.reg_mask;
 	value |= (priv->clk_csr << priv->hw->mii.clk_csr_shift)
 		& priv->hw->mii.clk_csr_mask;
-	if (priv->plat->has_gmac4)
+	if (priv->plat->has_gmac4 || priv->plat->has_emac3)
 		value |= MII_GMAC4_READ;
 
 	data = stmmac_mdio_read(priv, data, value);
@@ -381,7 +381,7 @@ static int stmmac_mdio_write_c22(struct mii_bus *bus, int phyaddr, int phyreg,
 
 	value |= (priv->clk_csr << priv->hw->mii.clk_csr_shift)
 		& priv->hw->mii.clk_csr_mask;
-	if (priv->plat->has_gmac4)
+	if (priv->plat->has_gmac4 || priv->plat->has_emac3)
 		value |= MII_GMAC4_WRITE;
 	else
 		value |= MII_WRITE;
@@ -482,7 +482,7 @@ int stmmac_mdio_reset(struct mii_bus *bus)
 	 * on MDC, so perform a dummy mdio read. To be updated for GMAC4
 	 * if needed.
 	 */
-	if (!priv->plat->has_gmac4)
+	if (!priv->plat->has_gmac4 && !priv->plat->has_emac3)
 		writel(0, priv->ioaddr + mii_address);
 #endif
 	return 0;
@@ -568,7 +568,7 @@ int stmmac_mdio_register(struct net_device *ndev)
 	} else {
 		new_bus->read = &stmmac_mdio_read_c22;
 		new_bus->write = &stmmac_mdio_write_c22;
-		if (priv->plat->has_gmac4) {
+		if (priv->plat->has_gmac4 || priv->plat->has_emac3) {
 			new_bus->read_c45 = &stmmac_mdio_read_c45;
 			new_bus->write_c45 = &stmmac_mdio_write_c45;
 		}
drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c +2 -2
index b4388ca8d211..9a8f9630d6af 100644
@@ -56,7 +56,7 @@ static int stmmac_adjust_time(struct ptp_clock_info *ptp, s64 delta)
 	bool xmac, est_rst = false;
 	int ret;
 
-	xmac = priv->plat->has_gmac4 || priv->plat->has_xgmac;
+	xmac = priv->plat->has_gmac4 || priv->plat->has_emac3 || priv->plat->has_xgmac;
 
 	if (delta < 0) {
 		neg_adj = 1;
@@ -292,7 +292,7 @@ void stmmac_ptp_register(struct stmmac_priv *priv)
 
 	/* Calculate the clock domain crossing (CDC) error if necessary */
 	priv->plat->cdc_error_adj = 0;
-	if (priv->plat->has_gmac4 && priv->plat->clk_ptp_rate)
+	if ((priv->plat->has_gmac4 || priv->plat->has_emac3) && priv->plat->clk_ptp_rate)
 		priv->plat->cdc_error_adj = (2 * NSEC_PER_SEC) / priv->plat->clk_ptp_rate;
 
 	stmmac_ptp_clock_ops.n_per_out = priv->dma_cap.pps_out_num;
include/linux/stmmac.h +1 -0
index a152678b82b7..de2d0a8693c8 100644
@@ -248,6 +248,7 @@ struct plat_stmmacenet_data {
 	struct stmmac_axi *axi;
 	int has_gmac4;
 	bool has_sun8i;
+	bool has_emac3;
 	bool tso_en;
 	int rss_en;
 	int mac_port_sel_speed;
Signature · 7 lines
2.39.2


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
maintainer
#15 lore raw

Re: [PATCH net-next v2 09/12] net: stmmac: Add EMAC3 variant of dwmac4

Quoted 6 lines · On Mon, 20 Mar 2023 17:16:14 -0500 Andrew Halaney wrote:

The next approach that was checked was to have a function pointer embedded inside a structure that does the appropriate conversion based on the variant that's in use. However, some of the function definitions are like the following:

void emac3_set_rx_ring_len(void __iomem *ioaddr, u32 len, u32 chan)

I checked a couple of callbacks and they seem to all be called with priv->iomem as an arg, so there is no strong reason to pass iomem instead of priv / hw. Or at least not to pass both..

I think that's a better approach than adding the wrappers :(

Are you familiar with coccinelle / spatch? It's often better than just regexps for refactoring, maybe it can help?

#16 lore raw

Re: [PATCH net-next v2 09/12] net: stmmac: Add EMAC3 variant of dwmac4

Quoted 8 lines · Jakub Kicinski
Quoted 6 lines · On Mon, 20 Mar 2023 17:16:14 -0500 Andrew Halaney wrote:

The next approach that was checked was to have a function pointer embedded inside a structure that does the appropriate conversion based on the variant that's in use. However, some of the function definitions are like the following:

void emac3_set_rx_ring_len(void __iomem *ioaddr, u32 len, u32 chan)

Quoted 9 lines

I checked a couple of callbacks and they seem to all be called with priv->iomem as an arg, so there is no strong reason to pass iomem instead of priv / hw. Or at least not to pass both..

I think that's a better approach than adding the wrappers :(

Are you familiar with coccinelle / spatch? It's often better than just regexps for refactoring, maybe it can help?

No worries, I'll try and refactor as you mentioned. Looking at it some this afternoon makes me think I'll try something like this:

    diff --git a/drivers/net/ethernet/stmicro/stmmac/hwif.h b/drivers/net/ethernet/stmicro/stmmac/hwif.h
    index 16a7421715cb..75c55f696c7a 100644
    --- a/drivers/net/ethernet/stmicro/stmmac/hwif.h
    +++ b/drivers/net/ethernet/stmicro/stmmac/hwif.h
    @@ -12,7 +12,7 @@
     ({ \
            int __result = -EINVAL; \
            if ((__priv)->hw->__module && (__priv)->hw->__module->__cname) { \
    -               (__priv)->hw->__module->__cname((__arg0), ##__args); \
    +               (__priv)->hw->__module->__cname((__priv), (__arg0), ##__args); \
                    __result = 0; \
            } \
            __result; \
    @@ -21,7 +21,7 @@
     ({ \
            int __result = -EINVAL; \
            if ((__priv)->hw->__module && (__priv)->hw->__module->__cname) \
    -               __result = (__priv)->hw->__module->__cname((__arg0), ##__args); \
    +               __result = (__priv)->hw->__module->__cname((__priv), (__arg0), ##__args); \
            __result; \
     })
     
    @@ -34,68 +34,68 @@ struct dma_edesc;
     /* Descriptors helpers */
     struct stmmac_desc_ops {
            /* DMA RX descriptor ring initialization */
    -       void (*init_rx_desc)(struct dma_desc *p, int disable_rx_ic, int mode,
    -                       int end, int bfsize);
    +       void (*init_rx_desc)(struct stmmac_priv *priv, struct dma_desc *p,
    +                            int disable_rx_ic, int mode, int end, int bfsize);
            /* DMA TX descriptor ring initialization */
    (...)

and then, I'll add something like:

    diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h
    index a152678b82b7..f5f406a09ae3 100644
    --- a/include/linux/stmmac.h
    +++ b/include/linux/stmmac.h
    @@ -273,5 +273,7 @@ struct plat_stmmacenet_data {
            bool use_phy_wol;
            bool sph_disable;
            bool serdes_up_after_phy_linkup;
    +       u32 mtl_base;
    +       u32 mtl_offset;
     };
     #endif

and rewrite:

    #define MTL_CHANX_BASE_ADDR(x)		(MTL_CHAN_BASE_ADDR + \
                                            (x * MTL_CHAN_BASE_OFFSET))

to use mtl_base/offset if they exist, and so on for the DMA versions, etc...

I'm sure I'll probably run into some issue and change course slightly, but thought I'd post a hint of the path to make sure I'm not way off the mark.

Thanks for your feedback,
Andrew

#17 lore raw

PATCH v2 10/12 net: stmmac: dwmac-qcom-ethqos: Respect phy-mode and TX delay

In reply to Andrew Halaney

The driver currently sets a MAC TX delay of 2 ns no matter what the phy-mode is. If the phy-mode indicates the phy is in charge of the TX delay (rgmii-txid, rgmii-id), don't do it in the MAC.

---

Changes since v1:
* Use a consistent subject prefix with other stmmac changes in series (myself)

 .../stmicro/stmmac/dwmac-qcom-ethqos.c        | 19 ++++++++++++++-----
 1 file changed, 14 insertions(+), 5 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +14 -5
index 32763566c214..e89937916741 100644
@@ -279,6 +279,16 @@ static int ethqos_dll_configure(struct qcom_ethqos *ethqos)
 
 static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos)
 {
+	int phy_mode;
+	int phase_shift;
+
+	/* Determine if the PHY adds a 2 ns TX delay or the MAC handles it */
+	phy_mode = device_get_phy_mode(&ethqos->pdev->dev);
+	if (phy_mode == PHY_INTERFACE_MODE_RGMII_ID || phy_mode == PHY_INTERFACE_MODE_RGMII_TXID)
+		phase_shift = 0;
+	else
+		phase_shift = RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN;
+
 	/* Disable loopback mode */
 	rgmii_updatel(ethqos, RGMII_CONFIG2_TX_TO_RX_LOOPBACK_EN,
 		      0, RGMII_IO_MACRO_CONFIG2);
@@ -300,9 +310,9 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos)
 			      RGMII_CONFIG_PROG_SWAP, RGMII_IO_MACRO_CONFIG);
 		rgmii_updatel(ethqos, RGMII_CONFIG2_DATA_DIVIDE_CLK_SEL,
 			      0, RGMII_IO_MACRO_CONFIG2);
+
 		rgmii_updatel(ethqos, RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN,
-			      RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN,
-			      RGMII_IO_MACRO_CONFIG2);
+				  phase_shift, RGMII_IO_MACRO_CONFIG2);
 		rgmii_updatel(ethqos, RGMII_CONFIG2_RSVD_CONFIG15,
 			      0, RGMII_IO_MACRO_CONFIG2);
 		rgmii_updatel(ethqos, RGMII_CONFIG2_RX_PROG_SWAP,
@@ -336,8 +346,7 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos)
 		rgmii_updatel(ethqos, RGMII_CONFIG2_DATA_DIVIDE_CLK_SEL,
 			      0, RGMII_IO_MACRO_CONFIG2);
 		rgmii_updatel(ethqos, RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN,
-			      RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN,
-			      RGMII_IO_MACRO_CONFIG2);
+				  phase_shift, RGMII_IO_MACRO_CONFIG2);
 		rgmii_updatel(ethqos, RGMII_CONFIG_MAX_SPD_PRG_2,
 			      BIT(6), RGMII_IO_MACRO_CONFIG);
 		rgmii_updatel(ethqos, RGMII_CONFIG2_RSVD_CONFIG15,
@@ -375,7 +384,7 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos)
 		rgmii_updatel(ethqos, RGMII_CONFIG2_DATA_DIVIDE_CLK_SEL,
 			      0, RGMII_IO_MACRO_CONFIG2);
 		rgmii_updatel(ethqos, RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN,
-			      0, RGMII_IO_MACRO_CONFIG2);
+				  phase_shift, RGMII_IO_MACRO_CONFIG2);
 		rgmii_updatel(ethqos, RGMII_CONFIG_MAX_SPD_PRG_9,
 			      BIT(12) | GENMASK(9, 8),
 			      RGMII_IO_MACRO_CONFIG);
Signature · 7 lines
2.39.2


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
maintainer
#18 lore raw

Re: [PATCH net-next v2 10/12] net: stmmac: dwmac-qcom-ethqos: Respect phy-mode and TX delay

drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c static int ethqos_dll_configure(struct qcom_ethqos *ethqos) · line 283

Quoted 4 lines · On Mon, 20 Mar 2023 17:16:15 -0500 Andrew Halaney wrote:

static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos) {

drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +2 -0
+	int phy_mode;
+	int phase_shift;

nit: invert the order, we like variable declaration lines longest to shortest

drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c static int ethqos_dll_configure(struct qcom_ethqos *ethqos) · line 287

Quoted 3 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +3 -0
+	/* Determine if the PHY adds a 2 ns TX delay or the MAC handles it */
+	phy_mode = device_get_phy_mode(&ethqos->pdev->dev);
+	if (phy_mode == PHY_INTERFACE_MODE_RGMII_ID || phy_mode == PHY_INTERFACE_MODE_RGMII_TXID)

Let's try to stick to 80 chars where reasonable, this would be easier to read as 2 lines.

Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +4 -0
+		phase_shift = 0;
+	else
+		phase_shift = RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN;
+
 	/* Disable loopback mode */
 	rgmii_updatel(ethqos, RGMII_CONFIG2_TX_TO_RX_LOOPBACK_EN,
 		      0, RGMII_IO_MACRO_CONFIG2);

drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos) · line 315

Quoted 8 lines
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +2 -2
@@ -300,9 +310,9 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos)
 			      RGMII_CONFIG_PROG_SWAP, RGMII_IO_MACRO_CONFIG);
 		rgmii_updatel(ethqos, RGMII_CONFIG2_DATA_DIVIDE_CLK_SEL,
 			      0, RGMII_IO_MACRO_CONFIG2);
+
 		rgmii_updatel(ethqos, RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN,
-			      RGMII_CONFIG2_TX_CLK_PHASE_SHIFT_EN,
-			      RGMII_IO_MACRO_CONFIG2);
+				  phase_shift, RGMII_IO_MACRO_CONFIG2);

here and in couple more places looks like indentation got broken? continuation line should start under the opening bracket + 1.

#19 lore raw

PATCH v2 11/12 net: stmmac: dwmac-qcom-ethqos: Use loopback_en for all speeds

In reply to Andrew Halaney

It seems that this variable should be used for all speeds, not just 1000/100.

While at it refactor it slightly to be more readable, including fixing the typo in the variable name.

---

Changes since v1:
* Use a consistent subject prefix with other stmmac changes in series (myself)

 .../stmicro/stmmac/dwmac-qcom-ethqos.c        | 36 +++++++++----------
 1 file changed, 17 insertions(+), 19 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +17 -19
index e89937916741..41e6f4fa92f3 100644
@@ -78,7 +78,7 @@ struct ethqos_emac_por {
 struct ethqos_emac_driver_data {
 	const struct ethqos_emac_por *por;
 	unsigned int num_por;
-	bool rgmii_config_looback_en;
+	bool rgmii_config_loopback_en;
 };
 
 struct qcom_ethqos {
@@ -91,7 +91,7 @@ struct qcom_ethqos {
 
 	const struct ethqos_emac_por *por;
 	unsigned int num_por;
-	bool rgmii_config_looback_en;
+	bool rgmii_config_loopback_en;
 };
 
 static int rgmii_readl(struct qcom_ethqos *ethqos, unsigned int offset)
@@ -183,7 +183,7 @@ static const struct ethqos_emac_por emac_v2_3_0_por[] = {
 static const struct ethqos_emac_driver_data emac_v2_3_0_data = {
 	.por = emac_v2_3_0_por,
 	.num_por = ARRAY_SIZE(emac_v2_3_0_por),
-	.rgmii_config_looback_en = true,
+	.rgmii_config_loopback_en = true,
 };
 
 static const struct ethqos_emac_por emac_v2_1_0_por[] = {
@@ -198,7 +198,7 @@ static const struct ethqos_emac_por emac_v2_1_0_por[] = {
 static const struct ethqos_emac_driver_data emac_v2_1_0_data = {
 	.por = emac_v2_1_0_por,
 	.num_por = ARRAY_SIZE(emac_v2_1_0_por),
-	.rgmii_config_looback_en = false,
+	.rgmii_config_loopback_en = false,
 };
 
 static int ethqos_dll_configure(struct qcom_ethqos *ethqos)
@@ -281,6 +281,7 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos)
 {
 	int phy_mode;
 	int phase_shift;
+	int loopback;
 
 	/* Determine if the PHY adds a 2 ns TX delay or the MAC handles it */
 	phy_mode = device_get_phy_mode(&ethqos->pdev->dev);
@@ -293,6 +294,12 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos)
 	rgmii_updatel(ethqos, RGMII_CONFIG2_TX_TO_RX_LOOPBACK_EN,
 		      0, RGMII_IO_MACRO_CONFIG2);
 
+	/* Determine if this platform wants loopback enabled after programming */
+	if (ethqos->rgmii_config_loopback_en)
+		loopback = RGMII_CONFIG_LOOPBACK_EN;
+	else
+		loopback = 0;
+
 	/* Select RGMII, write 0 to interface select */
 	rgmii_updatel(ethqos, RGMII_CONFIG_INTF_SEL,
 		      0, RGMII_IO_MACRO_CONFIG);
@@ -325,12 +332,8 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos)
 		rgmii_updatel(ethqos, SDCC_DDR_CONFIG_PRG_DLY_EN,
 			      SDCC_DDR_CONFIG_PRG_DLY_EN,
 			      SDCC_HC_REG_DDR_CONFIG);
-		if (ethqos->rgmii_config_looback_en)
-			rgmii_updatel(ethqos, RGMII_CONFIG_LOOPBACK_EN,
-				      RGMII_CONFIG_LOOPBACK_EN, RGMII_IO_MACRO_CONFIG);
-		else
-			rgmii_updatel(ethqos, RGMII_CONFIG_LOOPBACK_EN,
-				      0, RGMII_IO_MACRO_CONFIG);
+		rgmii_updatel(ethqos, RGMII_CONFIG_LOOPBACK_EN,
+			      loopback, RGMII_IO_MACRO_CONFIG);
 		break;
 
 	case SPEED_100:
@@ -362,13 +365,8 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos)
 		rgmii_updatel(ethqos, SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_EN,
 			      SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_EN,
 			      SDCC_HC_REG_DDR_CONFIG);
-		if (ethqos->rgmii_config_looback_en)
-			rgmii_updatel(ethqos, RGMII_CONFIG_LOOPBACK_EN,
-				      RGMII_CONFIG_LOOPBACK_EN, RGMII_IO_MACRO_CONFIG);
-		else
-			rgmii_updatel(ethqos, RGMII_CONFIG_LOOPBACK_EN,
-				      0, RGMII_IO_MACRO_CONFIG);
-
+		rgmii_updatel(ethqos, RGMII_CONFIG_LOOPBACK_EN,
+			      loopback, RGMII_IO_MACRO_CONFIG);
 		break;
 
 	case SPEED_10:
@@ -402,7 +400,7 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos)
 			      SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_EN,
 			      SDCC_HC_REG_DDR_CONFIG);
 		rgmii_updatel(ethqos, RGMII_CONFIG_LOOPBACK_EN,
-			      RGMII_CONFIG_LOOPBACK_EN, RGMII_IO_MACRO_CONFIG);
+			      loopback, RGMII_IO_MACRO_CONFIG);
 		break;
 	default:
 		dev_err(&ethqos->pdev->dev,
@@ -547,7 +545,7 @@ static int qcom_ethqos_probe(struct platform_device *pdev)
 	data = of_device_get_match_data(&pdev->dev);
 	ethqos->por = data->por;
 	ethqos->num_por = data->num_por;
-	ethqos->rgmii_config_looback_en = data->rgmii_config_looback_en;
+	ethqos->rgmii_config_loopback_en = data->rgmii_config_loopback_en;
 
 	ethqos->rgmii_clk = devm_clk_get(&pdev->dev, "rgmii");
 	if (IS_ERR(ethqos->rgmii_clk)) {
Signature · 7 lines
2.39.2


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#20 lore raw

PATCH v2 12/12 net: stmmac: dwmac-qcom-ethqos: Add EMAC3 support

In reply to Andrew Halaney

Add the new programming sequence needed for EMAC3 based platforms such as the sc8280xp family.

---

Changes since v1:
* None

 .../stmicro/stmmac/dwmac-qcom-ethqos.c        | 106 ++++++++++++++----
 1 file changed, 84 insertions(+), 22 deletions(-)
drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +84 -22
index 41e6f4fa92f3..1fe8563b9c0d 100644
@@ -11,6 +11,7 @@
 
 #define RGMII_IO_MACRO_CONFIG		0x0
 #define SDCC_HC_REG_DLL_CONFIG		0x4
+#define SDCC_TEST_CTL			0x8
 #define SDCC_HC_REG_DDR_CONFIG		0xC
 #define SDCC_HC_REG_DLL_CONFIG2		0x10
 #define SDC4_STATUS			0x14
@@ -49,6 +50,7 @@
 #define SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY	GENMASK(26, 21)
 #define SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_CODE	GENMASK(29, 27)
 #define SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_EN	BIT(30)
+#define SDCC_DDR_CONFIG_TCXO_CYCLES_CNT		GENMASK(11, 9)
 #define SDCC_DDR_CONFIG_PRG_RCLK_DLY		GENMASK(8, 0)
 
 /* SDCC_HC_REG_DLL_CONFIG2 fields */
@@ -79,6 +81,7 @@ struct ethqos_emac_driver_data {
 	const struct ethqos_emac_por *por;
 	unsigned int num_por;
 	bool rgmii_config_loopback_en;
+	bool has_emac3;
 };
 
 struct qcom_ethqos {
@@ -92,6 +95,7 @@ struct qcom_ethqos {
 	const struct ethqos_emac_por *por;
 	unsigned int num_por;
 	bool rgmii_config_loopback_en;
+	bool has_emac3;
 };
 
 static int rgmii_readl(struct qcom_ethqos *ethqos, unsigned int offset)
@@ -184,6 +188,7 @@ static const struct ethqos_emac_driver_data emac_v2_3_0_data = {
 	.por = emac_v2_3_0_por,
 	.num_por = ARRAY_SIZE(emac_v2_3_0_por),
 	.rgmii_config_loopback_en = true,
+	.has_emac3 = false,
 };
 
 static const struct ethqos_emac_por emac_v2_1_0_por[] = {
@@ -199,6 +204,23 @@ static const struct ethqos_emac_driver_data emac_v2_1_0_data = {
 	.por = emac_v2_1_0_por,
 	.num_por = ARRAY_SIZE(emac_v2_1_0_por),
 	.rgmii_config_loopback_en = false,
+	.has_emac3 = false,
+};
+
+static const struct ethqos_emac_por emac_v3_0_0_por[] = {
+	{ .offset = RGMII_IO_MACRO_CONFIG,	.value = 0x40c01343 },
+	{ .offset = SDCC_HC_REG_DLL_CONFIG,	.value = 0x2004642c },
+	{ .offset = SDCC_HC_REG_DDR_CONFIG,	.value = 0x80040800 },
+	{ .offset = SDCC_HC_REG_DLL_CONFIG2,	.value = 0x00200000 },
+	{ .offset = SDCC_USR_CTL,		.value = 0x00010800 },
+	{ .offset = RGMII_IO_MACRO_CONFIG2,	.value = 0x00002060 },
+};
+
+static const struct ethqos_emac_driver_data emac_v3_0_0_data = {
+	.por = emac_v3_0_0_por,
+	.num_por = ARRAY_SIZE(emac_v3_0_0_por),
+	.rgmii_config_loopback_en = false,
+	.has_emac3 = true,
 };
 
 static int ethqos_dll_configure(struct qcom_ethqos *ethqos)
@@ -222,11 +244,13 @@ static int ethqos_dll_configure(struct qcom_ethqos *ethqos)
 	rgmii_updatel(ethqos, SDCC_DLL_CONFIG_DLL_EN,
 		      SDCC_DLL_CONFIG_DLL_EN, SDCC_HC_REG_DLL_CONFIG);
 
-	rgmii_updatel(ethqos, SDCC_DLL_MCLK_GATING_EN,
-		      0, SDCC_HC_REG_DLL_CONFIG);
+	if (!ethqos->has_emac3) {
+		rgmii_updatel(ethqos, SDCC_DLL_MCLK_GATING_EN,
+			      0, SDCC_HC_REG_DLL_CONFIG);
 
-	rgmii_updatel(ethqos, SDCC_DLL_CDR_FINE_PHASE,
-		      0, SDCC_HC_REG_DLL_CONFIG);
+		rgmii_updatel(ethqos, SDCC_DLL_CDR_FINE_PHASE,
+			      0, SDCC_HC_REG_DLL_CONFIG);
+	}
 
 	/* Wait for CK_OUT_EN clear */
 	do {
@@ -261,18 +285,20 @@ static int ethqos_dll_configure(struct qcom_ethqos *ethqos)
 	rgmii_updatel(ethqos, SDCC_DLL_CONFIG2_DDR_CAL_EN,
 		      SDCC_DLL_CONFIG2_DDR_CAL_EN, SDCC_HC_REG_DLL_CONFIG2);
 
-	rgmii_updatel(ethqos, SDCC_DLL_CONFIG2_DLL_CLOCK_DIS,
-		      0, SDCC_HC_REG_DLL_CONFIG2);
+	if (!ethqos->has_emac3) {
+		rgmii_updatel(ethqos, SDCC_DLL_CONFIG2_DLL_CLOCK_DIS,
+			      0, SDCC_HC_REG_DLL_CONFIG2);
 
-	rgmii_updatel(ethqos, SDCC_DLL_CONFIG2_MCLK_FREQ_CALC,
-		      0x1A << 10, SDCC_HC_REG_DLL_CONFIG2);
+		rgmii_updatel(ethqos, SDCC_DLL_CONFIG2_MCLK_FREQ_CALC,
+			      0x1A << 10, SDCC_HC_REG_DLL_CONFIG2);
 
-	rgmii_updatel(ethqos, SDCC_DLL_CONFIG2_DDR_TRAFFIC_INIT_SEL,
-		      BIT(2), SDCC_HC_REG_DLL_CONFIG2);
+		rgmii_updatel(ethqos, SDCC_DLL_CONFIG2_DDR_TRAFFIC_INIT_SEL,
+			      BIT(2), SDCC_HC_REG_DLL_CONFIG2);
 
-	rgmii_updatel(ethqos, SDCC_DLL_CONFIG2_DDR_TRAFFIC_INIT_SW,
-		      SDCC_DLL_CONFIG2_DDR_TRAFFIC_INIT_SW,
-		      SDCC_HC_REG_DLL_CONFIG2);
+		rgmii_updatel(ethqos, SDCC_DLL_CONFIG2_DDR_TRAFFIC_INIT_SW,
+			      SDCC_DLL_CONFIG2_DDR_TRAFFIC_INIT_SW,
+			      SDCC_HC_REG_DLL_CONFIG2);
+	}
 
 	return 0;
 }
@@ -326,9 +352,17 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos)
 			      RGMII_CONFIG2_RX_PROG_SWAP,
 			      RGMII_IO_MACRO_CONFIG2);
 
-		/* Set PRG_RCLK_DLY to 57 for 1.8 ns delay */
-		rgmii_updatel(ethqos, SDCC_DDR_CONFIG_PRG_RCLK_DLY,
-			      57, SDCC_HC_REG_DDR_CONFIG);
+		/* PRG_RCLK_DLY = TCXO period * TCXO_CYCLES_CNT / 2 * RX delay ns,
+		 * in practice this becomes PRG_RCLK_DLY = 52 * 4 / 2 * RX delay ns
+		 */
+		if (ethqos->has_emac3)
+			/* 0.9 ns */
+			rgmii_updatel(ethqos, SDCC_DDR_CONFIG_PRG_RCLK_DLY,
+				      115, SDCC_HC_REG_DDR_CONFIG);
+		else
+			/* 1.8 ns */
+			rgmii_updatel(ethqos, SDCC_DDR_CONFIG_PRG_RCLK_DLY,
+				      57, SDCC_HC_REG_DDR_CONFIG);
 		rgmii_updatel(ethqos, SDCC_DDR_CONFIG_PRG_DLY_EN,
 			      SDCC_DDR_CONFIG_PRG_DLY_EN,
 			      SDCC_HC_REG_DDR_CONFIG);
@@ -354,8 +388,15 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos)
 			      BIT(6), RGMII_IO_MACRO_CONFIG);
 		rgmii_updatel(ethqos, RGMII_CONFIG2_RSVD_CONFIG15,
 			      0, RGMII_IO_MACRO_CONFIG2);
-		rgmii_updatel(ethqos, RGMII_CONFIG2_RX_PROG_SWAP,
-			      0, RGMII_IO_MACRO_CONFIG2);
+
+		if (ethqos->has_emac3)
+			rgmii_updatel(ethqos, RGMII_CONFIG2_RX_PROG_SWAP,
+				      RGMII_CONFIG2_RX_PROG_SWAP,
+				      RGMII_IO_MACRO_CONFIG2);
+		else
+			rgmii_updatel(ethqos, RGMII_CONFIG2_RX_PROG_SWAP,
+				      0, RGMII_IO_MACRO_CONFIG2);
+
 		/* Write 0x5 to PRG_RCLK_DLY_CODE */
 		rgmii_updatel(ethqos, SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_CODE,
 			      (BIT(29) | BIT(27)), SDCC_HC_REG_DDR_CONFIG);
@@ -388,8 +429,13 @@ static int ethqos_rgmii_macro_init(struct qcom_ethqos *ethqos)
 			      RGMII_IO_MACRO_CONFIG);
 		rgmii_updatel(ethqos, RGMII_CONFIG2_RSVD_CONFIG15,
 			      0, RGMII_IO_MACRO_CONFIG2);
-		rgmii_updatel(ethqos, RGMII_CONFIG2_RX_PROG_SWAP,
-			      0, RGMII_IO_MACRO_CONFIG2);
+		if (ethqos->has_emac3)
+			rgmii_updatel(ethqos, RGMII_CONFIG2_RX_PROG_SWAP,
+				      RGMII_CONFIG2_RX_PROG_SWAP,
+				      RGMII_IO_MACRO_CONFIG2);
+		else
+			rgmii_updatel(ethqos, RGMII_CONFIG2_RX_PROG_SWAP,
+				      0, RGMII_IO_MACRO_CONFIG2);
 		/* Write 0x5 to PRG_RCLK_DLY_CODE */
 		rgmii_updatel(ethqos, SDCC_DDR_CONFIG_EXT_PRG_RCLK_DLY_CODE,
 			      (BIT(29) | BIT(27)), SDCC_HC_REG_DDR_CONFIG);
@@ -432,6 +478,17 @@ static int ethqos_configure(struct qcom_ethqos *ethqos)
 	rgmii_updatel(ethqos, SDCC_DLL_CONFIG_PDN,
 		      SDCC_DLL_CONFIG_PDN, SDCC_HC_REG_DLL_CONFIG);
 
+	if (ethqos->has_emac3) {
+		if (ethqos->speed == SPEED_1000) {
+			rgmii_writel(ethqos, 0x1800000, SDCC_TEST_CTL);
+			rgmii_writel(ethqos, 0x2C010800, SDCC_USR_CTL);
+			rgmii_writel(ethqos, 0xA001, SDCC_HC_REG_DLL_CONFIG2);
+		} else {
+			rgmii_writel(ethqos, 0x40010800, SDCC_USR_CTL);
+			rgmii_writel(ethqos, 0xA001, SDCC_HC_REG_DLL_CONFIG2);
+		}
+	}
+
 	/* Clear DLL_RST */
 	rgmii_updatel(ethqos, SDCC_DLL_CONFIG_DLL_RST, 0,
 		      SDCC_HC_REG_DLL_CONFIG);
@@ -451,7 +508,9 @@ static int ethqos_configure(struct qcom_ethqos *ethqos)
 			      SDCC_HC_REG_DLL_CONFIG);
 
 		/* Set USR_CTL bit 26 with mask of 3 bits */
-		rgmii_updatel(ethqos, GENMASK(26, 24), BIT(26), SDCC_USR_CTL);
+		if (!ethqos->has_emac3)
+			rgmii_updatel(ethqos, GENMASK(26, 24), BIT(26),
+				      SDCC_USR_CTL);
 
 		/* wait for DLL LOCK */
 		do {
@@ -546,6 +605,7 @@ static int qcom_ethqos_probe(struct platform_device *pdev)
 	ethqos->por = data->por;
 	ethqos->num_por = data->num_por;
 	ethqos->rgmii_config_loopback_en = data->rgmii_config_loopback_en;
+	ethqos->has_emac3 = data->has_emac3;
 
 	ethqos->rgmii_clk = devm_clk_get(&pdev->dev, "rgmii");
 	if (IS_ERR(ethqos->rgmii_clk)) {
@@ -564,7 +624,8 @@ static int qcom_ethqos_probe(struct platform_device *pdev)
 	plat_dat->bsp_priv = ethqos;
 	plat_dat->fix_mac_speed = ethqos_fix_mac_speed;
 	plat_dat->dump_debug_regs = rgmii_dump;
-	plat_dat->has_gmac4 = 1;
+	plat_dat->has_gmac4 = !data->has_emac3;
+	plat_dat->has_emac3 = data->has_emac3;
 	plat_dat->pmt = 1;
 	plat_dat->tso_en = of_property_read_bool(np, "snps,tso");
 	if (of_device_is_compatible(np, "qcom,qcs404-ethqos"))
@@ -603,6 +664,7 @@ static int qcom_ethqos_remove(struct platform_device *pdev)
 static const struct of_device_id qcom_ethqos_match[] = {
 	{ .compatible = "qcom,qcs404-ethqos", .data = &emac_v2_3_0_data},
 	{ .compatible = "qcom,sm8150-ethqos", .data = &emac_v2_1_0_data},
+	{ .compatible = "qcom,sc8280xp-ethqos", &emac_v3_0_0_data},
 	{ }
 };
 MODULE_DEVICE_TABLE(of, qcom_ethqos_match);
Signature · 7 lines
2.39.2


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
maintainer
#21 lore raw
In reply to Andrew Halaney
Quoted 10 lines · On Mon, 20 Mar 2023 17:16:05 -0500 Andrew Halaney wrote:

This is a forward port / upstream refactor of code delivered downstream by Qualcomm over at [0] to enable the DWMAC5 based implementation called EMAC3 on the sa8540p-ride dev board.

From what I can tell with the board schematic in hand, as well as the code delivered, the main changes needed are:

1. A new address space layout for /dwmac5/EMAC3 MTL/DMA regs
2. A new programming sequence required for the EMAC3 base platforms

Quoted 6 lines

This series makes those adaptations as well as other housekeeping items such as converting dt-bindings to yaml, adding clock descriptions, etc.

[0] https://git.codelinaro.org/clo/la/kernel/ark-5.14/-/commit/510235ad02d7f0df478146fb00d7a4ba74821b17

v1: https://lore.kernel.org/netdev/[email protected]/

At a glance 1-4,8-12 need to go via networking, 5 via clock tree, and 6,7 via ARM/Qualcomm.

AFAICT there are no strong (compile) dependencies so we can each merge our chunk and they will meet in Linus's tree? If so please repost just the networking stuff for net-next, and the other bits to respective trees, as separate series.

#22 lore raw
Quoted 18 lines · Jakub Kicinski
Quoted 10 lines · On Mon, 20 Mar 2023 17:16:05 -0500 Andrew Halaney wrote:

This is a forward port / upstream refactor of code delivered downstream by Qualcomm over at [0] to enable the DWMAC5 based implementation called EMAC3 on the sa8540p-ride dev board.

From what I can tell with the board schematic in hand, as well as the code delivered, the main changes needed are:

1. A new address space layout for /dwmac5/EMAC3 MTL/DMA regs
2. A new programming sequence required for the EMAC3 base platforms

Quoted 6 lines

This series makes those adaptations as well as other housekeeping items such as converting dt-bindings to yaml, adding clock descriptions, etc.

[0] https://git.codelinaro.org/clo/la/kernel/ark-5.14/-/commit/510235ad02d7f0df478146fb00d7a4ba74821b17

v1: https://lore.kernel.org/netdev/[email protected]/

Quoted 8 lines

At a glance 1-4,8-12 need to go via networking, 5 via clock tree, and 6,7 via ARM/Qualcomm.

AFAICT there are no strong (compile) dependencies so we can each merge our chunk and they will meet in Linus's tree? If so please repost just the networking stuff for net-next, and the other bits to respective trees, as separate series.

That makes sense to me, thanks for the advice.

The only note is that 5 (the clk patch) is depended on by 6/7 to compile (they use the header value in 5)... So I'll keep those together!

So all in all it will be the dt-binding changes + stmmac changes in one series for networking, and the clock + devicetree changes via ARM/Qualcomm if I am following properly.

I'll go that route for v3 and link here (just to make finding the split easier) unless someone objects (got some time as I need to refactor based on series feedback)!

Thanks,
Andrew

maintainer
#23 lore raw
Quoted 28 lines · Andrew Halaney
Quoted 18 lines · Jakub Kicinski
Quoted 10 lines · On Mon, 20 Mar 2023 17:16:05 -0500 Andrew Halaney wrote:

This is a forward port / upstream refactor of code delivered downstream by Qualcomm over at [0] to enable the DWMAC5 based implementation called EMAC3 on the sa8540p-ride dev board.

From what I can tell with the board schematic in hand, as well as the code delivered, the main changes needed are:

1. A new address space layout for /dwmac5/EMAC3 MTL/DMA regs
2. A new programming sequence required for the EMAC3 base platforms

Quoted 6 lines

This series makes those adaptations as well as other housekeeping items such as converting dt-bindings to yaml, adding clock descriptions, etc.

[0] https://git.codelinaro.org/clo/la/kernel/ark-5.14/-/commit/510235ad02d7f0df478146fb00d7a4ba74821b17

v1: https://lore.kernel.org/netdev/[email protected]/

Quoted 8 lines

At a glance 1-4,8-12 need to go via networking, 5 via clock tree, and 6,7 via ARM/Qualcomm.

AFAICT there are no strong (compile) dependencies so we can each merge our chunk and they will meet in Linus's tree? If so please repost just the networking stuff for net-next, and the other bits to respective trees, as separate series.

Quoted 5 lines

That makes sense to me, thanks for the advice.

The only note is that 5 (the clk patch) is depended on by 6/7 to compile (they use the header value in 5)... So I'll keep those together!

Sounds good to me!

Regards,
Bjorn

Quoted 11 lines

So all in all it will be the dt-binding changes + stmmac changes in one series for networking, and the clock + devicetree changes via ARM/Qualcomm if I am following properly.

I'll go that route for v3 and link here (just to make finding the split easier) unless someone objects (got some time as I need to refactor based on series feedback)!

Thanks,
Andrew