Add EMAC3 support for sa8540p-ride (devicetree/clk bits)
Subsystems (7)
v3 cover Add EMAC3 support for sa8540p-ride (devicetree/clk bits)
This is a forward port / upstream refactor of code delivered downstream by Qualcomm over at [0] to enable the DWMAC5 based implementation called EMAC3 on the sa8540p-ride dev board.
From what I can tell with the board schematic in hand, as well as the code delivered, the main changes needed are:
1. A new address space layout for /dwmac5/EMAC3 MTL/DMA regs
2. A new programming sequence required for the EMAC3 base platforms
This series addresses the devicetree and clock changes to support this hardware bringup.
As requested[1], it has been split up by compile time / maintainer tree. The associated v3 of the netdev specific changes can be found at [2]. Together, they result in the ethernet controller working for both controllers on this platform.
[0] https://git.codelinaro.org/clo/la/kernel/ark-5.14/-/commit/510235ad02d7f0df478146fb00d7a4ba74821b17
[1] https://lore.kernel.org/netdev/[email protected]/
[2] https://lore.kernel.org/netdev/[email protected]/T/#m0afcad0e8031c02bcb5dbfb86cb8acfc287968fe
v2: https://lore.kernel.org/netdev/[email protected]/
v1: https://lore.kernel.org/netdev/[email protected]/
Thanks,
Andrew
Andrew Halaney (3):
clk: qcom: gcc-sc8280xp: Add EMAC GDSCs
arm64: dts: qcom: sc8280xp: Add ethernet nodes
arm64: dts: qcom: sa8540p-ride: Add ethernet nodes
arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 181 ++++++++++++++++++ arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 59 ++++++ drivers/clk/qcom/gcc-sc8280xp.c | 18 ++ include/dt-bindings/clock/qcom,gcc-sc8280xp.h | 2 + 4 files changed, 260 insertions(+)
Signature · 1 line
2.39.2
PATCH v3 1/3 clk: qcom: gcc-sc8280xp: Add EMAC GDSCs
Add the EMAC GDSCs to allow the EMAC hardware to be enabled.
---
Changes since v2:
* Add Konrad's Reviewed-by
Changes since v1:
* Add Stephen's Acked-by
* Explicitly tested on x13s laptop with no noticeable side effect (Konrad)
drivers/clk/qcom/gcc-sc8280xp.c | 18 ++++++++++++++++++ include/dt-bindings/clock/qcom,gcc-sc8280xp.h | 2 ++ 2 files changed, 20 insertions(+)
drivers/clk/qcom/gcc-sc8280xp.c +18 -0
@@ -6873,6 +6873,22 @@ static struct gdsc usb30_sec_gdsc = { .pwrsts = PWRSTS_RET_ON, }; +static struct gdsc emac_0_gdsc = { + .gdscr =0xaa004 , + .pd = { + .name ="emac_0_gdsc" , + }, + .pwrsts =PWRSTS_OFF_ON , +}; + +static struct gdsc emac_1_gdsc = { + .gdscr =0xba004 , + .pd = { + .name ="emac_1_gdsc" , + }, + .pwrsts =PWRSTS_OFF_ON , +}; +static struct clk_regmap *gcc_sc8280xp_clocks[] = { [GCC_AGGRE_NOC_PCIE0_TUNNEL_AXI_CLK ] = &gcc_aggre_noc_pcie0_tunnel_axi_clk.clkr, [GCC_AGGRE_NOC_PCIE1_TUNNEL_AXI_CLK ] = &gcc_aggre_noc_pcie1_tunnel_axi_clk.clkr,
@@ -7351,6 +7367,8 @@ static struct gdsc *gcc_sc8280xp_gdscs[] = { [USB30_MP_GDSC] = &usb30_mp_gdsc, [USB30_PRIM_GDSC] = &usb30_prim_gdsc, [USB30_SEC_GDSC] = &usb30_sec_gdsc, + [EMAC_0_GDSC] = &emac_0_gdsc, + [EMAC_1_GDSC] = &emac_1_gdsc, };static const struct clk_rcg_dfs_data gcc_dfs_clocks[] = {
include/dt-bindings/clock/qcom,gcc-sc8280xp.h +2 -0
@@ -492,5 +492,7 @@#define USB30_MP_GDSC 9#define USB30_PRIM_GDSC 10#define USB30_SEC_GDSC 11 +#define EMAC_0_GDSC 12 +#define EMAC_1_GDSC 13#endif
Signature · 1 line
2.39.2
PATCH v3 2/3 arm64: dts: qcom: sc8280xp: Add ethernet nodes
In reply to Andrew HalaneyThis platform has 2 MACs integrated in it, go ahead and describe them.
---
Changes since v2:
* Fix spacing (Konrad)
Changes since v1:
* None
arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 59 ++++++++++++++++++++++++++ 1 file changed, 59 insertions(+)
arch/arm64/boot/dts/qcom/sc8280xp.dtsi +59 -0
@@ -761,6 +761,65 @@ soc: soc@0 { ranges = <0 0 0 0 0x10 0>; dma-ranges = <0 0 0 0 0x10 0>; + ethernet0: ethernet@20000 { + compatible = "qcom,sc8280xp-ethqos"; + reg = <0x0 0x00020000 0x0 0x10000>, + <0x0 0x00036000 0x0 0x100>; + reg-names = "stmmaceth", "rgmii"; + + clocks = <&gcc GCC_EMAC0_AXI_CLK>, + <&gcc GCC_EMAC0_SLV_AHB_CLK>, + <&gcc GCC_EMAC0_PTP_CLK>, + <&gcc GCC_EMAC0_RGMII_CLK>; + clock-names = "stmmaceth", + "pclk", + "ptp_ref", + "rgmii"; + + interrupts = <GIC_SPI 946 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 936 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq", "eth_lpi"; + iommus = <&apps_smmu 0x4c0 0xf>; + power-domains = <&gcc EMAC_0_GDSC>; + + snps,tso; + snps,pbl = <32>; + rx-fifo-depth = <4096>; + tx-fifo-depth = <4096>; + + status = "disabled"; + }; + + ethernet1: ethernet@23000000 { + compatible = "qcom,sc8280xp-ethqos"; + reg = <0x0 0x23000000 0x0 0x10000>, + <0x0 0x23016000 0x0 0x100>; + reg-names = "stmmaceth", "rgmii"; + + clocks = <&gcc GCC_EMAC1_AXI_CLK>, + <&gcc GCC_EMAC1_SLV_AHB_CLK>, + <&gcc GCC_EMAC1_PTP_CLK>, + <&gcc GCC_EMAC1_RGMII_CLK>; + clock-names = "stmmaceth", + "pclk", + "ptp_ref", + "rgmii"; + + interrupts = <GIC_SPI 929 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 919 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq", "eth_lpi"; + + iommus = <&apps_smmu 0x40 0xf>; + power-domains = <&gcc EMAC_1_GDSC>; + + snps,tso; + snps,pbl = <32>; + rx-fifo-depth = <4096>; + tx-fifo-depth = <4096>; + + status = "disabled"; + }; + gcc: clock-controller@100000 { compatible = "qcom,gcc-sc8280xp"; reg = <0x0 0x00100000 0x0 0x1f0000>;
Signature · 1 line
2.39.2
Re: [PATCH v3 2/3] arm64: dts: qcom: sc8280xp: Add ethernet nodes
Quoted 42 lines · Andrew Halaney
This platform has 2 MACs integrated in it, go ahead and describe them.
Signed-off-by Andrew Halaney <[email protected]>---
Changes since v2:
* Fix spacing (Konrad)Changes since v1:
* Nonearch/arm64/boot/dts/qcom/sc8280xp.dtsi | 59 ++++++++++++++++++++++++++ 1 file changed, 59 insertions(+)arch/arm64/boot/dts/qcom/sc8280xp.dtsi +20
-0@@ -761,6 +761,65 @@ soc: soc@0 { ranges = <0 0 0 0 0x10 0>; dma-ranges = <0 0 0 0 0x10 0>; + ethernet0: ethernet@20000 { + compatible = "qcom,sc8280xp-ethqos"; + reg = <0x0 0x00020000 0x0 0x10000>, + <0x0 0x00036000 0x0 0x100>; + reg-names = "stmmaceth", "rgmii"; + + clocks = <&gcc GCC_EMAC0_AXI_CLK>, + <&gcc GCC_EMAC0_SLV_AHB_CLK>, + <&gcc GCC_EMAC0_PTP_CLK>, + <&gcc GCC_EMAC0_RGMII_CLK>; + clock-names = "stmmaceth", + "pclk", + "ptp_ref", + "rgmii"; + + interrupts = <GIC_SPI 946 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 936 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq", "eth_lpi"; + iommus = <&apps_smmu 0x4c0 0xf>; + power-domains = <&gcc EMAC_0_GDSC>;
arch/arm64/boot/dts/qcom/sc8280xp.dtsi soc: soc@0 { · line 793
Quoted 10 lines
arch/arm64/boot/dts/qcom/sc8280xp.dtsi +10
-0+ + snps,tso; + snps,pbl = <32>; + rx-fifo-depth = <4096>; + tx-fifo-depth = <4096>; + + status = "disabled"; + }; + + ethernet1: ethernet@23000000 {
Nodes under /soc should be ordered by their unit address, so in this case it belongs after dispcc1: clock-controller@..
With that fixed:
Konrad
Quoted 32 lines
arch/arm64/boot/dts/qcom/sc8280xp.dtsi +29
-0+ compatible = "qcom,sc8280xp-ethqos"; + reg = <0x0 0x23000000 0x0 0x10000>, + <0x0 0x23016000 0x0 0x100>; + reg-names = "stmmaceth", "rgmii"; + + clocks = <&gcc GCC_EMAC1_AXI_CLK>, + <&gcc GCC_EMAC1_SLV_AHB_CLK>, + <&gcc GCC_EMAC1_PTP_CLK>, + <&gcc GCC_EMAC1_RGMII_CLK>; + clock-names = "stmmaceth", + "pclk", + "ptp_ref", + "rgmii"; + + interrupts = <GIC_SPI 929 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 919 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq", "eth_lpi"; + + iommus = <&apps_smmu 0x40 0xf>; + power-domains = <&gcc EMAC_1_GDSC>; + + snps,tso; + snps,pbl = <32>; + rx-fifo-depth = <4096>; + tx-fifo-depth = <4096>; + + status = "disabled"; + }; + gcc: clock-controller@100000 { compatible = "qcom,gcc-sc8280xp"; reg = <0x0 0x00100000 0x0 0x1f0000>;
PATCH v3 3/3 arm64: dts: qcom: sa8540p-ride: Add ethernet nodes
In reply to Andrew HalaneyEnable both the MACs found on the board.
ethernet0 and ethernet1 both ultimately go to a series of on board switches which aren't managed by this processor.
ethernet0 is connected to a Marvell 88EA1512 phy via RGMII. That goes to the series of switches via SGMII on the "media" side of the phy. RGMII_SGMII mode is enabled via devicetree register descriptions. The switch on the "media" side has auto-negotiation disabled, so configuration from userspace similar to:
ethtool -s eth0 autoneg off speed 1000 duplex full
is necessary to get traffic flowing on that interface.
ethernet1 is in a mac2mac/fixed-link configuration going to the same series of switches directly via RGMII.
---
Changes since v1 and v2:
* None
arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 181 ++++++++++++++++++++++ 1 file changed, 181 insertions(+)
arch/arm64/boot/dts/qcom/sa8540p-ride.dts +181 -0
@@ -28,6 +28,65 @@ aliases { chosen { stdout-path = "serial0:115200n8"; }; + + mtl_rx_setup: rx-queues-config { + snps,rx-queues-to-use = <1>; + snps,rx-sched-sp; + + queue0 { + snps,dcb-algorithm; + snps,map-to-dma-channel = <0x0>; + snps,route-up; + snps,priority = <0x1>; + }; + + queue1 { + snps,dcb-algorithm; + snps,map-to-dma-channel = <0x1>; + snps,route-ptp; + }; + + queue2 { + snps,avb-algorithm; + snps,map-to-dma-channel = <0x2>; + snps,route-avcp; + }; + + queue3 { + snps,avb-algorithm; + snps,map-to-dma-channel = <0x3>; + snps,priority = <0xc>; + }; + }; + + mtl_tx_setup: tx-queues-config { + snps,tx-queues-to-use = <1>; + snps,tx-sched-sp; + + queue0 { + snps,dcb-algorithm; + }; + + queue1 { + snps,dcb-algorithm; + }; + + queue2 { + snps,avb-algorithm; + snps,send_slope = <0x1000>; + snps,idle_slope = <0x1000>; + snps,high_credit = <0x3e800>; + snps,low_credit = <0xffc18000>; + }; + + queue3 { + snps,avb-algorithm; + snps,send_slope = <0x1000>; + snps,idle_slope = <0x1000>; + snps,high_credit = <0x3e800>; + snps,low_credit = <0xffc18000>; + }; + }; }; &apps_rsc {
@@ -151,6 +210,68 @@ vreg_l8g: ldo8 { }; }; +ðernet0 { + snps,mtl-rx-config = <&mtl_rx_setup>; + snps,mtl-tx-config = <&mtl_tx_setup>; + + max-speed = <1000>; + phy-handle = <&rgmii_phy>; + phy-mode = "rgmii-txid"; + + pinctrl-names = "default"; + pinctrl-0 = <ðernet0_default>; + + status = "okay"; + + mdio { + #address-cells = <0x1>; + #size-cells = <0x0>; + + compatible = "snps,dwmac-mdio"; + + /* Marvell 88EA1512 */ + rgmii_phy: phy@8 { + reg = <0x8>; + + interrupt-parent = <&tlmm>; + interrupts-extended = <&tlmm 127 IRQ_TYPE_EDGE_FALLING>; + + reset-gpios = <&pmm8540c_gpios 1 GPIO_ACTIVE_LOW>; + reset-assert-us = <11000>; + reset-deassert-us = <70000>; + + device_type = "ethernet-phy"; + + /* Set to RGMII_SGMII mode and soft reset. Turn off auto-negotiation + * from userspace to talk to the switch on the SGMII side of things + */ + marvell,reg-init = + /* Set MODE[2:0] to RGMII_SGMII */ + <0x12 0x14 0xfff8 0x4>, + /* Soft reset required after changing MODE[2:0] */ + <0x12 0x14 0x7fff 0x8000>; + }; + }; +}; + +ðernet1 { + snps,mtl-rx-config = <&mtl_rx_setup>; + snps,mtl-tx-config = <&mtl_tx_setup>; + + max-speed = <1000>; + phy-mode = "rgmii-txid"; + + pinctrl-names = "default"; + pinctrl-0 = <ðernet1_default>; + + status = "okay"; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + &i2c0 { pinctrl-names = "default"; pinctrl-0 = <&i2c0_default>;
@@ -316,6 +437,66 @@ &xo_board_clk { /* PINCTRL */ &tlmm { + ethernet0_default: ethernet0-default-state { + mdc-pins { + pins = "gpio175"; + function = "rgmii_0"; + drive-strength = <16>; + bias-pull-up; + }; + + mdio-pins { + pins = "gpio176"; + function = "rgmii_0"; + drive-strength = <16>; + bias-pull-up; + }; + + rgmii-tx-pins { + pins = "gpio183", "gpio184", "gpio185", "gpio186", "gpio187", "gpio188"; + function = "rgmii_0"; + drive-strength = <16>; + bias-pull-up; + }; + + rgmii-rx-pins { + pins = "gpio177", "gpio178", "gpio179", "gpio180", "gpio181", "gpio182"; + function = "rgmii_0"; + drive-strength = <16>; + bias-disable; + }; + }; + + ethernet1_default: ethernet1-default-state { + mdc-pins { + pins = "gpio97"; + function = "rgmii_1"; + drive-strength = <16>; + bias-pull-up; + }; + + mdio-pins { + pins = "gpio98"; + function = "rgmii_1"; + drive-strength = <16>; + bias-pull-up; + }; + + rgmii-tx-pins { + pins = "gpio105", "gpio106", "gpio107", "gpio108", "gpio109", "gpio110"; + function = "rgmii_1"; + drive-strength = <16>; + bias-pull-up; + }; + + rgmii-rx-pins { + pins = "gpio99", "gpio100", "gpio101", "gpio102", "gpio103", "gpio104"; + function = "rgmii_1"; + drive-strength = <16>; + bias-disable; + }; + }; + i2c0_default: i2c0-default-state { /* To USB7002T-I/KDXVA0 USB hub (SIP1 only) */ pins = "gpio135", "gpio136";
Signature · 1 line
2.39.2
Re: [PATCH v3 3/3] arm64: dts: qcom: sa8540p-ride: Add ethernet nodes
Quoted 14 lines · Andrew Halaney
Enable both the MACs found on the board.
ethernet0 and ethernet1 both ultimately go to a series of on board switches which aren't managed by this processor.
+ðernet0 {
arch/arm64/boot/dts/qcom/sa8540p-ride.dts +7
-0+ snps,mtl-rx-config = <&mtl_rx_setup>; + snps,mtl-tx-config = <&mtl_tx_setup>; + + max-speed = <1000>; + phy-handle = <&rgmii_phy>; + phy-mode = "rgmii-txid"; +
arch/arm64/boot/dts/qcom/sa8540p-ride.dts vreg_l8g: ldo8 { · line 230
Quoted 10 lines
arch/arm64/boot/dts/qcom/sa8540p-ride.dts +10
-0+ pinctrl-names = "default"; + pinctrl-0 = <ðernet0_default>; + + status = "okay"; + + mdio { + #address-cells = <0x1>; + #size-cells = <0x0>; + + compatible = "snps,dwmac-mdio";
Compatible is always, always the first property.
Best regards,
Krzysztof