Skip to contentSkip to conversation

Add EMAC3 support for sa8540p-ride (devicetree/clk bits)

PATCH Superseded Andrew Halaney 3 participants 6 messages Mar 31, 2023 – Apr 4, 2023

Subsystems (7)

v3 of 6 Superseded Latest is v6 →

lore
Share & tools
lore
#0 lore raw

v3 cover Add EMAC3 support for sa8540p-ride (devicetree/clk bits)

This is a forward port / upstream refactor of code delivered downstream by Qualcomm over at [0] to enable the DWMAC5 based implementation called EMAC3 on the sa8540p-ride dev board.

From what I can tell with the board schematic in hand, as well as the code delivered, the main changes needed are:

1. A new address space layout for /dwmac5/EMAC3 MTL/DMA regs
2. A new programming sequence required for the EMAC3 base platforms

This series addresses the devicetree and clock changes to support this hardware bringup.

As requested[1], it has been split up by compile time / maintainer tree. The associated v3 of the netdev specific changes can be found at [2]. Together, they result in the ethernet controller working for both controllers on this platform.

[0] https://git.codelinaro.org/clo/la/kernel/ark-5.14/-/commit/510235ad02d7f0df478146fb00d7a4ba74821b17
[1] https://lore.kernel.org/netdev/[email protected]/
[2] https://lore.kernel.org/netdev/[email protected]/T/#m0afcad0e8031c02bcb5dbfb86cb8acfc287968fe

v2: https://lore.kernel.org/netdev/[email protected]/
v1: https://lore.kernel.org/netdev/[email protected]/

Thanks,
Andrew

Andrew Halaney (3):
clk: qcom: gcc-sc8280xp: Add EMAC GDSCs
arm64: dts: qcom: sc8280xp: Add ethernet nodes
arm64: dts: qcom: sa8540p-ride: Add ethernet nodes

 arch/arm64/boot/dts/qcom/sa8540p-ride.dts     | 181 ++++++++++++++++++
 arch/arm64/boot/dts/qcom/sc8280xp.dtsi        |  59 ++++++
 drivers/clk/qcom/gcc-sc8280xp.c               |  18 ++
 include/dt-bindings/clock/qcom,gcc-sc8280xp.h |   2 +
 4 files changed, 260 insertions(+)
Signature · 1 line
2.39.2
#1 lore raw

PATCH v3 1/3 clk: qcom: gcc-sc8280xp: Add EMAC GDSCs

Add the EMAC GDSCs to allow the EMAC hardware to be enabled.

---

Changes since v2:
* Add Konrad's Reviewed-by

Changes since v1:
* Add Stephen's Acked-by
* Explicitly tested on x13s laptop with no noticeable side effect (Konrad)

 drivers/clk/qcom/gcc-sc8280xp.c               | 18 ++++++++++++++++++
 include/dt-bindings/clock/qcom,gcc-sc8280xp.h |  2 ++
 2 files changed, 20 insertions(+)
drivers/clk/qcom/gcc-sc8280xp.c +18 -0
index b3198784e1c3..04a99dbaa57e 100644
@@ -6873,6 +6873,22 @@ static struct gdsc usb30_sec_gdsc = {
 	.pwrsts = PWRSTS_RET_ON,
 };
 
+static struct gdsc emac_0_gdsc = {
+	.gdscr = 0xaa004,
+	.pd = {
+		.name = "emac_0_gdsc",
+	},
+	.pwrsts = PWRSTS_OFF_ON,
+};
+
+static struct gdsc emac_1_gdsc = {
+	.gdscr = 0xba004,
+	.pd = {
+		.name = "emac_1_gdsc",
+	},
+	.pwrsts = PWRSTS_OFF_ON,
+};
+
 static struct clk_regmap *gcc_sc8280xp_clocks[] = {
 	[GCC_AGGRE_NOC_PCIE0_TUNNEL_AXI_CLK] = &gcc_aggre_noc_pcie0_tunnel_axi_clk.clkr,
 	[GCC_AGGRE_NOC_PCIE1_TUNNEL_AXI_CLK] = &gcc_aggre_noc_pcie1_tunnel_axi_clk.clkr,
@@ -7351,6 +7367,8 @@ static struct gdsc *gcc_sc8280xp_gdscs[] = {
 	[USB30_MP_GDSC] = &usb30_mp_gdsc,
 	[USB30_PRIM_GDSC] = &usb30_prim_gdsc,
 	[USB30_SEC_GDSC] = &usb30_sec_gdsc,
+	[EMAC_0_GDSC] = &emac_0_gdsc,
+	[EMAC_1_GDSC] = &emac_1_gdsc,
 };
 
 static const struct clk_rcg_dfs_data gcc_dfs_clocks[] = {
include/dt-bindings/clock/qcom,gcc-sc8280xp.h +2 -0
index cb2fb638825c..721105ea4fad 100644
@@ -492,5 +492,7 @@
 #define USB30_MP_GDSC					9
 #define USB30_PRIM_GDSC					10
 #define USB30_SEC_GDSC					11
+#define EMAC_0_GDSC					12
+#define EMAC_1_GDSC					13
 
 #endif
Signature · 1 line
2.39.2
#2 lore raw

PATCH v3 2/3 arm64: dts: qcom: sc8280xp: Add ethernet nodes

In reply to Andrew Halaney

This platform has 2 MACs integrated in it, go ahead and describe them.

---

Changes since v2:
* Fix spacing (Konrad)

Changes since v1:
* None

 arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 59 ++++++++++++++++++++++++++
 1 file changed, 59 insertions(+)
arch/arm64/boot/dts/qcom/sc8280xp.dtsi +59 -0
index 42bfa9fa5b96..f28ea86b128d 100644
@@ -761,6 +761,65 @@ soc: soc@0 {
 		ranges = <0 0 0 0 0x10 0>;
 		dma-ranges = <0 0 0 0 0x10 0>;
 
+		ethernet0: ethernet@20000 {
+			compatible = "qcom,sc8280xp-ethqos";
+			reg = <0x0 0x00020000 0x0 0x10000>,
+			      <0x0 0x00036000 0x0 0x100>;
+			reg-names = "stmmaceth", "rgmii";
+
+			clocks = <&gcc GCC_EMAC0_AXI_CLK>,
+				 <&gcc GCC_EMAC0_SLV_AHB_CLK>,
+				 <&gcc GCC_EMAC0_PTP_CLK>,
+				 <&gcc GCC_EMAC0_RGMII_CLK>;
+			clock-names = "stmmaceth",
+				      "pclk",
+				      "ptp_ref",
+				      "rgmii";
+
+			interrupts = <GIC_SPI 946 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 936 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq", "eth_lpi";
+			iommus = <&apps_smmu 0x4c0 0xf>;
+			power-domains = <&gcc EMAC_0_GDSC>;
+
+			snps,tso;
+			snps,pbl = <32>;
+			rx-fifo-depth = <4096>;
+			tx-fifo-depth = <4096>;
+
+			status = "disabled";
+		};
+
+		ethernet1: ethernet@23000000 {
+			compatible = "qcom,sc8280xp-ethqos";
+			reg = <0x0 0x23000000 0x0 0x10000>,
+			      <0x0 0x23016000 0x0 0x100>;
+			reg-names = "stmmaceth", "rgmii";
+
+			clocks = <&gcc GCC_EMAC1_AXI_CLK>,
+				 <&gcc GCC_EMAC1_SLV_AHB_CLK>,
+				 <&gcc GCC_EMAC1_PTP_CLK>,
+				 <&gcc GCC_EMAC1_RGMII_CLK>;
+			clock-names = "stmmaceth",
+				      "pclk",
+				      "ptp_ref",
+				      "rgmii";
+
+			interrupts = <GIC_SPI 929 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 919 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq", "eth_lpi";
+
+			iommus = <&apps_smmu 0x40 0xf>;
+			power-domains = <&gcc EMAC_1_GDSC>;
+
+			snps,tso;
+			snps,pbl = <32>;
+			rx-fifo-depth = <4096>;
+			tx-fifo-depth = <4096>;
+
+			status = "disabled";
+		};
+
 		gcc: clock-controller@100000 {
 			compatible = "qcom,gcc-sc8280xp";
 			reg = <0x0 0x00100000 0x0 0x1f0000>;
Signature · 1 line
2.39.2
Reviewed-by on v3 2/3
#3 lore raw

Re: [PATCH v3 2/3] arm64: dts: qcom: sc8280xp: Add ethernet nodes

Quoted 42 lines · Andrew Halaney

This platform has 2 MACs integrated in it, go ahead and describe them.

---

Changes since v2:
* Fix spacing (Konrad)

Changes since v1:
* None

 arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 59 ++++++++++++++++++++++++++
 1 file changed, 59 insertions(+)
arch/arm64/boot/dts/qcom/sc8280xp.dtsi +20 -0
index 42bfa9fa5b96..f28ea86b128d 100644
@@ -761,6 +761,65 @@ soc: soc@0 {
 		ranges = <0 0 0 0 0x10 0>;
 		dma-ranges = <0 0 0 0 0x10 0>;
 
+		ethernet0: ethernet@20000 {
+			compatible = "qcom,sc8280xp-ethqos";
+			reg = <0x0 0x00020000 0x0 0x10000>,
+			      <0x0 0x00036000 0x0 0x100>;
+			reg-names = "stmmaceth", "rgmii";
+
+			clocks = <&gcc GCC_EMAC0_AXI_CLK>,
+				 <&gcc GCC_EMAC0_SLV_AHB_CLK>,
+				 <&gcc GCC_EMAC0_PTP_CLK>,
+				 <&gcc GCC_EMAC0_RGMII_CLK>;
+			clock-names = "stmmaceth",
+				      "pclk",
+				      "ptp_ref",
+				      "rgmii";
+
+			interrupts = <GIC_SPI 946 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 936 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq", "eth_lpi";
+			iommus = <&apps_smmu 0x4c0 0xf>;
+			power-domains = <&gcc EMAC_0_GDSC>;

arch/arm64/boot/dts/qcom/sc8280xp.dtsi soc: soc@0 { · line 793

Quoted 10 lines
arch/arm64/boot/dts/qcom/sc8280xp.dtsi +10 -0
+
+			snps,tso;
+			snps,pbl = <32>;
+			rx-fifo-depth = <4096>;
+			tx-fifo-depth = <4096>;
+
+			status = "disabled";
+		};
+
+		ethernet1: ethernet@23000000 {

Nodes under /soc should be ordered by their unit address, so in this case it belongs after dispcc1: clock-controller@..

With that fixed:

Konrad

Quoted 32 lines
arch/arm64/boot/dts/qcom/sc8280xp.dtsi +29 -0
+			compatible = "qcom,sc8280xp-ethqos";
+			reg = <0x0 0x23000000 0x0 0x10000>,
+			      <0x0 0x23016000 0x0 0x100>;
+			reg-names = "stmmaceth", "rgmii";
+
+			clocks = <&gcc GCC_EMAC1_AXI_CLK>,
+				 <&gcc GCC_EMAC1_SLV_AHB_CLK>,
+				 <&gcc GCC_EMAC1_PTP_CLK>,
+				 <&gcc GCC_EMAC1_RGMII_CLK>;
+			clock-names = "stmmaceth",
+				      "pclk",
+				      "ptp_ref",
+				      "rgmii";
+
+			interrupts = <GIC_SPI 929 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 919 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq", "eth_lpi";
+
+			iommus = <&apps_smmu 0x40 0xf>;
+			power-domains = <&gcc EMAC_1_GDSC>;
+
+			snps,tso;
+			snps,pbl = <32>;
+			rx-fifo-depth = <4096>;
+			tx-fifo-depth = <4096>;
+
+			status = "disabled";
+		};
+
 		gcc: clock-controller@100000 {
 			compatible = "qcom,gcc-sc8280xp";
 			reg = <0x0 0x00100000 0x0 0x1f0000>;
#4 lore raw

PATCH v3 3/3 arm64: dts: qcom: sa8540p-ride: Add ethernet nodes

In reply to Andrew Halaney

Enable both the MACs found on the board.

ethernet0 and ethernet1 both ultimately go to a series of on board switches which aren't managed by this processor.

ethernet0 is connected to a Marvell 88EA1512 phy via RGMII. That goes to the series of switches via SGMII on the "media" side of the phy. RGMII_SGMII mode is enabled via devicetree register descriptions. The switch on the "media" side has auto-negotiation disabled, so configuration from userspace similar to:

ethtool -s eth0 autoneg off speed 1000 duplex full

is necessary to get traffic flowing on that interface.

ethernet1 is in a mac2mac/fixed-link configuration going to the same series of switches directly via RGMII.

---

Changes since v1 and v2:
* None

 arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 181 ++++++++++++++++++++++
 1 file changed, 181 insertions(+)
arch/arm64/boot/dts/qcom/sa8540p-ride.dts +181 -0
index 40db5aa0803c..eb230265aa45 100644
@@ -28,6 +28,65 @@ aliases {
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	mtl_rx_setup: rx-queues-config {
+		snps,rx-queues-to-use = <1>;
+		snps,rx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+			snps,map-to-dma-channel = <0x0>;
+			snps,route-up;
+			snps,priority = <0x1>;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+			snps,map-to-dma-channel = <0x1>;
+			snps,route-ptp;
+		};
+
+		queue2 {
+			snps,avb-algorithm;
+			snps,map-to-dma-channel = <0x2>;
+			snps,route-avcp;
+		};
+
+		queue3 {
+			snps,avb-algorithm;
+			snps,map-to-dma-channel = <0x3>;
+			snps,priority = <0xc>;
+		};
+	};
+
+	mtl_tx_setup: tx-queues-config {
+		snps,tx-queues-to-use = <1>;
+		snps,tx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+		};
+
+		queue2 {
+			snps,avb-algorithm;
+			snps,send_slope = <0x1000>;
+			snps,idle_slope = <0x1000>;
+			snps,high_credit = <0x3e800>;
+			snps,low_credit = <0xffc18000>;
+		};
+
+		queue3 {
+			snps,avb-algorithm;
+			snps,send_slope = <0x1000>;
+			snps,idle_slope = <0x1000>;
+			snps,high_credit = <0x3e800>;
+			snps,low_credit = <0xffc18000>;
+		};
+	};
 };
 
 &apps_rsc {
@@ -151,6 +210,68 @@ vreg_l8g: ldo8 {
 	};
 };
 
+&ethernet0 {
+	snps,mtl-rx-config = <&mtl_rx_setup>;
+	snps,mtl-tx-config = <&mtl_tx_setup>;
+
+	max-speed = <1000>;
+	phy-handle = <&rgmii_phy>;
+	phy-mode = "rgmii-txid";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&ethernet0_default>;
+
+	status = "okay";
+
+	mdio {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		compatible = "snps,dwmac-mdio";
+
+		/* Marvell 88EA1512 */
+		rgmii_phy: phy@8 {
+			reg = <0x8>;
+
+			interrupt-parent = <&tlmm>;
+			interrupts-extended = <&tlmm 127 IRQ_TYPE_EDGE_FALLING>;
+
+			reset-gpios = <&pmm8540c_gpios 1 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <11000>;
+			reset-deassert-us = <70000>;
+
+			device_type = "ethernet-phy";
+
+			/* Set to RGMII_SGMII mode and soft reset. Turn off auto-negotiation
+			 * from userspace to talk to the switch on the SGMII side of things
+			 */
+			marvell,reg-init =
+				/* Set MODE[2:0] to RGMII_SGMII */
+				<0x12 0x14 0xfff8 0x4>,
+				/* Soft reset required after changing MODE[2:0] */
+				<0x12 0x14 0x7fff 0x8000>;
+		};
+	};
+};
+
+&ethernet1 {
+	snps,mtl-rx-config = <&mtl_rx_setup>;
+	snps,mtl-tx-config = <&mtl_tx_setup>;
+
+	max-speed = <1000>;
+	phy-mode = "rgmii-txid";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&ethernet1_default>;
+
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
 &i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_default>;
@@ -316,6 +437,66 @@ &xo_board_clk {
 /* PINCTRL */
 
 &tlmm {
+	ethernet0_default: ethernet0-default-state {
+		mdc-pins {
+			pins = "gpio175";
+			function = "rgmii_0";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		mdio-pins {
+			pins = "gpio176";
+			function = "rgmii_0";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		rgmii-tx-pins {
+			pins = "gpio183", "gpio184", "gpio185", "gpio186", "gpio187", "gpio188";
+			function = "rgmii_0";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		rgmii-rx-pins {
+			pins = "gpio177", "gpio178", "gpio179", "gpio180", "gpio181", "gpio182";
+			function = "rgmii_0";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	ethernet1_default: ethernet1-default-state {
+		mdc-pins {
+			pins = "gpio97";
+			function = "rgmii_1";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		mdio-pins {
+			pins = "gpio98";
+			function = "rgmii_1";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		rgmii-tx-pins {
+			pins = "gpio105", "gpio106", "gpio107", "gpio108", "gpio109", "gpio110";
+			function = "rgmii_1";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		rgmii-rx-pins {
+			pins = "gpio99", "gpio100", "gpio101", "gpio102", "gpio103", "gpio104";
+			function = "rgmii_1";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
 	i2c0_default: i2c0-default-state {
 		/* To USB7002T-I/KDXVA0 USB hub (SIP1 only) */
 		pins = "gpio135", "gpio136";
Signature · 1 line
2.39.2
#5 lore raw

Re: [PATCH v3 3/3] arm64: dts: qcom: sa8540p-ride: Add ethernet nodes

Quoted 14 lines · Andrew Halaney

Enable both the MACs found on the board.

ethernet0 and ethernet1 both ultimately go to a series of on board switches which aren't managed by this processor.

+&ethernet0 {

arch/arm64/boot/dts/qcom/sa8540p-ride.dts +7 -0
+	snps,mtl-rx-config = <&mtl_rx_setup>;
+	snps,mtl-tx-config = <&mtl_tx_setup>;
+
+	max-speed = <1000>;
+	phy-handle = <&rgmii_phy>;
+	phy-mode = "rgmii-txid";
+

arch/arm64/boot/dts/qcom/sa8540p-ride.dts vreg_l8g: ldo8 { · line 230

Quoted 10 lines
arch/arm64/boot/dts/qcom/sa8540p-ride.dts +10 -0
+	pinctrl-names = "default";
+	pinctrl-0 = <&ethernet0_default>;
+
+	status = "okay";
+
+	mdio {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		compatible = "snps,dwmac-mdio";

Compatible is always, always the first property.

Best regards,
Krzysztof