Skip to contentSkip to conversation

dt-bindings: arm: Add Gateworks i.MX8M Mini GW7905-0x board

PATCH Superseded Tim Harvey 2 participants 4 messages Jun 9, 2023 – Jul 19, 2023

Subsystems (2)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore

Tim Harvey

author
#0 lore raw

PATCH v2 1/2 dt-bindings: arm: Add Gateworks i.MX8M Mini GW7905-0x board

Add DT compatible string for a Gateworks GW7905-0x board based on the i.MX8M Mini from NXP.

---
v2:
- sort alphabetically

---
 Documentation/devicetree/bindings/arm/fsl.yaml | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/arm/fsl.yaml +1 -0
index 15d411084065..3a053e3e5929 100644
@@ -902,6 +902,7 @@ properties:
               - fsl,imx8mm-ddr4-evk       # i.MX8MM DDR4 EVK Board
               - fsl,imx8mm-evk            # i.MX8MM EVK Board
               - gateworks,imx8mm-gw7904
+              - gateworks,imx8mm-gw7905-0x # i.MX8MM Gateworks Board
               - gw,imx8mm-gw71xx-0x       # i.MX8MM Gateworks Development Kit
               - gw,imx8mm-gw72xx-0x       # i.MX8MM Gateworks Development Kit
               - gw,imx8mm-gw73xx-0x       # i.MX8MM Gateworks Development Kit
Signature · 1 line
2.25.1
author
#1 lore raw

PATCH v2 2/2 arm64: dts: freescale: Add imx8mm-venice-gw7905-0x

The Gateworks imx8mm-venice-gw7905-0x consists of a SOM + baseboard.

The GW700x SOM contains the following:
- i.MX8M Mini SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button controller, and ADC's
- PMIC
- SOM connector providing:
- FEC GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 2.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO

The GW7905 Baseboard contains the following:
- GPS
- microSD
- off-board I/O connector with I2C, SPI, GPIO
- EERPOM
- PCIe clock generator
- 1x full-length miniPCIe socket with PCI/USB3 (via mux) and USB2.0
- 1x half-length miniPCIe socket with USB2.0 and USB3.0
- USB 3.0 HUB
- USB Type-C with USB PD Sink capability and peripheral support
- USB Type-C with USB 3.0 host support

---
v2 - no changes

---
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../dts/freescale/imx8mm-venice-gw7905-0x.dts |  28 ++
 .../dts/freescale/imx8mm-venice-gw7905.dtsi   | 303 ++++++++++++++++++
 3 files changed, 332 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw7905-0x.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw7905.dtsi
arch/arm64/boot/dts/freescale/Makefile +1 -0
index d94d464db03e..f13faf043d48 100644
@@ -73,6 +73,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7901.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7902.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7903.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7904.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7905-0x.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-nonwifi-dahlia.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-nonwifi-dev.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-nonwifi-yavia.dtb
arch/arm64/boot/dts/freescale/imx8mm-venice-gw7905-0x.dts new file +28 -0
new file mode 100644
index 000000000000..914753f062cd
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2023 Gateworks Corporation
+ */
+
+/dts-v1/;
+
+#include "imx8mm.dtsi"
+#include "imx8mm-venice-gw700x.dtsi"
+#include "imx8mm-venice-gw7905.dtsi"
+
+/ {
+	model = "Gateworks Venice GW7905-0x i.MX8MM Development Kit";
+	compatible = "gateworks,imx8mm-gw7905-0x", "fsl,imx8mm";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+};
+
+/* Disable SOM interfaces not used on baseboard */
+&fec1 {
+	status = "disabled";
+};
+
+&usdhc1 {
+	status = "disabled";
+};
arch/arm64/boot/dts/freescale/imx8mm-venice-gw7905.dtsi new file +303 -0

303 lines not on this page · raw message

Signature · 1 line
2.25.1
author
#2 lore raw

Re: [PATCH v2 2/2] arm64: dts: freescale: Add imx8mm-venice-gw7905-0x

Quoted 400 lines · Tim Harvey

The Gateworks imx8mm-venice-gw7905-0x consists of a SOM + baseboard.

The GW700x SOM contains the following:
- i.MX8M Mini SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button controller, and ADC's
- PMIC
- SOM connector providing:
- FEC GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 2.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO

The GW7905 Baseboard contains the following:
- GPS
- microSD
- off-board I/O connector with I2C, SPI, GPIO
- EERPOM
- PCIe clock generator
- 1x full-length miniPCIe socket with PCI/USB3 (via mux) and USB2.0
- 1x half-length miniPCIe socket with USB2.0 and USB3.0
- USB 3.0 HUB
- USB Type-C with USB PD Sink capability and peripheral support
- USB Type-C with USB 3.0 host support

---
v2 - no changes

---
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../dts/freescale/imx8mm-venice-gw7905-0x.dts |  28 ++
 .../dts/freescale/imx8mm-venice-gw7905.dtsi   | 303 ++++++++++++++++++
 3 files changed, 332 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw7905-0x.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw7905.dtsi
arch/arm64/boot/dts/freescale/Makefile +1 -0
index d94d464db03e..f13faf043d48 100644
@@ -73,6 +73,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7901.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7902.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7903.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7904.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7905-0x.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-nonwifi-dahlia.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-nonwifi-dev.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-nonwifi-yavia.dtb
arch/arm64/boot/dts/freescale/imx8mm-venice-gw7905-0x.dts new file +28 -0
new file mode 100644
index 000000000000..914753f062cd
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2023 Gateworks Corporation
+ */
+
+/dts-v1/;
+
+#include "imx8mm.dtsi"
+#include "imx8mm-venice-gw700x.dtsi"
+#include "imx8mm-venice-gw7905.dtsi"
+
+/ {
+       model = "Gateworks Venice GW7905-0x i.MX8MM Development Kit";
+       compatible = "gateworks,imx8mm-gw7905-0x", "fsl,imx8mm";
+
+       chosen {
+               stdout-path = &uart2;
+       };
+};
+
+/* Disable SOM interfaces not used on baseboard */
+&fec1 {
+       status = "disabled";
+};
+
+&usdhc1 {
+       status = "disabled";
+};
arch/arm64/boot/dts/freescale/imx8mm-venice-gw7905.dtsi new file +303 -1
new file mode 100644
index 000000000000..9646eb9e4928
@@ -0,0 +1,303 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2023 Gateworks Corporation
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/phy/phy-imx8-pcie.h>
+
+/ {
+       led-controller {
+               compatible = "gpio-leds";
+               pinctrl-names = "default";
+               pinctrl-0 = <&pinctrl_gpio_leds>;
+
+               led-0 {
+                       function = LED_FUNCTION_STATUS;
+                       color = <LED_COLOR_ID_GREEN>;
+                       gpios = <&gpio4 0 GPIO_ACTIVE_HIGH>;
+                       default-state = "on";
+                       linux,default-trigger = "heartbeat";
+               };
+
+               led-1 {
+                       function = LED_FUNCTION_STATUS;
+                       color = <LED_COLOR_ID_RED>;
+                       gpios = <&gpio4 2 GPIO_ACTIVE_HIGH>;
+                       default-state = "off";
+               };
+       };
+
+       pcie0_refclk: pcie0-refclk {
+               compatible = "fixed-clock";
+               #clock-cells = <0>;
+               clock-frequency = <100000000>;
+       };
+
+       pps {
+               compatible = "pps-gpio";
+               pinctrl-names = "default";
+               pinctrl-0 = <&pinctrl_pps>;
+               gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>;
+               status = "okay";
+       };
+
+       reg_usb2_vbus: regulator-usb2-vbus {
+               pinctrl-names = "default";
+               pinctrl-0 = <&pinctrl_reg_usb2_en>;
+               compatible = "regulator-fixed";
+               regulator-name = "usb2_vbus";
+               gpio = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+               enable-active-high;
+               regulator-min-microvolt = <5000000>;
+               regulator-max-microvolt = <5000000>;
+       };
+
+       reg_usdhc2_vmmc: regulator-usdhc2 {
+               pinctrl-names = "default";
+               pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+               compatible = "regulator-fixed";
+               regulator-name = "SD2_3P3V";
+               regulator-min-microvolt = <3300000>;
+               regulator-max-microvolt = <3300000>;
+               gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+               enable-active-high;
+       };
+};
+
+/* off-board header */
+&ecspi2 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_spi2>;
+       cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+       status = "okay";
+};
+
+&gpio1 {
+       gpio-line-names =
+               "", "", "", "",
+               "", "", "", "",
+               "", "", "", "",
+               "", "gpioa", "gpiob", "",
+               "", "", "", "",
+               "", "", "", "",
+               "", "", "", "",
+               "", "", "", "";
+};
+
+&gpio4 {
+       gpio-line-names =
+               "", "", "", "pci_usb_sel",
+               "", "", "", "pci_wdis#",
+               "", "", "", "",
+               "", "", "", "",
+               "", "", "", "",
+               "", "", "", "",
+               "", "", "", "",
+               "", "", "", "";
+};
+
+&gpio5 {
+       gpio-line-names =
+               "", "", "", "",
+               "gpioc", "gpiod", "", "",
+               "", "", "", "",
+               "", "", "", "",
+               "", "", "", "",
+               "", "", "", "",
+               "", "", "", "",
+               "", "", "", "";
+};
+
+&i2c2 {
+       clock-frequency = <400000>;
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_i2c2>;
+       status = "okay";
+
+       eeprom@52 {
+               compatible = "atmel,24c32";
+               reg = <0x52>;
+               pagesize = <32>;
+       };
+};
+
+/* off-board header */
+&i2c3 {
+       clock-frequency = <400000>;
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_i2c3>;
+       status = "okay";
+};
+
+&pcie_phy {
+       fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
+       fsl,clkreq-unsupported;
+       clocks = <&pcie0_refclk>;
+       clock-names = "ref";
+       status = "okay";
+};
+
+&pcie0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_pcie0>;
+       reset-gpio = <&gpio4 6 GPIO_ACTIVE_LOW>;
+       status = "okay";
+};
+
+/* GPS */
+&uart1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_uart1>;
+       status = "okay";
+};
+
+/* USB1 - Type C front panel SINK port J14 */
+&usbotg1 {
+       dr_mode = "peripheral";
+       status = "okay";
+};
+
+/* USB2 4-port USB3.0 HUB:
+ *  P1 - USBC connector (host only)
+ *  P2 - USB2 test connector
+ *  P3 - miniPCIe full card
+ *  P4 - miniPCIe half card
+ */
+&usbotg2 {
+       dr_mode = "host";
+       vbus-supply = <&reg_usb2_vbus>;
+       status = "okay";
+};
+
+/* microSD */
+&usdhc2 {
+       pinctrl-names = "default", "state_100mhz", "state_200mhz";
+       pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+       pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+       pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+       cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+       vmmc-supply = <&reg_usdhc2_vmmc>;
+       bus-width = <4>;
+       status = "okay";
+};
+
+&iomuxc {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_hog>;
+
+       pinctrl_hog: hoggrp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_GPIO1_IO13_GPIO1_IO13      0x40000040 /* GPIOA */
+                       MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14      0x40000040 /* GPIOB */
+                       MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3        0x40000106 /* PCI_USBSEL */
+                       MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7        0x40000106 /* PCIE_WDIS# */
+                       MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5    0x40000040 /* GPIOD */
+                       MX8MM_IOMUXC_SPDIF_RX_GPIO5_IO4         0x40000040 /* GPIOC */
+               >;
+       };
+
+       pinctrl_gpio_leds: gpioledgrp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0        0x6     /* LEDG */
+                       MX8MM_IOMUXC_SAI1_RXD0_GPIO4_IO2        0x6     /* LEDR */
+               >;
+       };
+
+       pinctrl_i2c2: i2c2grp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL          0x400001c2
+                       MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA          0x400001c2
+               >;
+       };
+
+       pinctrl_i2c3: i2c3grp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL          0x400001c2
+                       MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA          0x400001c2
+               >;
+       };
+
+       pinctrl_pcie0: pciegrp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_SAI1_RXD4_GPIO4_IO6        0x106
+               >;
+       };
+
+       pinctrl_pps: ppsgrp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5        0x106
+               >;
+       };
+
+       pinctrl_reg_usb2_en: regusb2grp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8       0x6     /* USBHUB_RST# (ext p/u) */
+               >;
+       };
+
+       pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19     0x40
+               >;
+       };
+
+       pinctrl_spi2: spi2grp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK    0x140
+                       MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI    0x140
+                       MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO    0x140
+                       MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13      0x140
+               >;
+       };
+
+       pinctrl_uart1: uart1grp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX     0x140
+                       MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX     0x140
+               >;
+       };
+
+       pinctrl_usdhc2: usdhc2grp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK         0x190
+                       MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD         0x1d0
+                       MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0     0x1d0
+                       MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1     0x1d0
+                       MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2     0x1d0
+                       MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3     0x1d0
+                       MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT  0xc0
+               >;
+       };
+
+       pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK         0x194
+                       MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD         0x1d4
+                       MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0     0x1d4
+                       MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1     0x1d4
+                       MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2     0x1d4
+                       MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3     0x1d4
+                       MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT  0xc0
+               >;
+       };
+
+       pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK         0x196
+                       MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD         0x1d6
+                       MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0     0x1d6
+                       MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1     0x1d6
+                       MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2     0x1d6
+                       MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3     0x1d6
+                       MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT  0xc0
+               >;
+       };
+
+       pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12        0x1c4
+               >;
+       };
+};
--
Quoted 2 lines

2.25.1

Hi Shawn,

I'm not sure if you missed this one or if you had some rework that you wanted?

Best regards,

Tim