leds: trigger: netdev: add additional modes
Subsystems (3)
v4 cover leds: trigger: netdev: add additional modes
This is a continue of [1]. It was decided to take a more gradual approach to implement LEDs support for switch and phy starting with basic support and then implementing the hw control part when we have all the prereq done.
This should be the final part for the netdev trigger.
I added net-next tag and added netdev mailing list since I was informed that this should be merged with netdev branch.
We collect some info around and we found a good set of modes that are common in almost all the PHY and Switch.
These modes are:
- Modes for dedicated link speed(10, 100, 1000 mbps). Additional mode can be added later following this example.
- Modes for half and full duplex.
The original idea was to add hw control only modes.
While the concept makes sense in practice it would results in lots of additional code and extra check to make sure we are setting correct modes.
With the suggestion from Andrew it was pointed out that using the ethtool APIs we can actually get the current link speed and duplex and this effectively removed the problem of having hw control only modes since we can fallback to software.
Since these modes are supported by software, we can skip providing an user for this in the LED driver to support hw control for these new modes (that will come right after this is merged) and prevent this to be another multi subsystem series.
For link speed and duplex we use ethtool APIs.
To call ethtool APIs, rtnl lock is needed but this can be skipped on handling netdev events as the lock is already held.
[1] https://lore.kernel.org/lkml/[email protected]/
Changes v4:
- Add net-next tag
- Add additional patch to expose hw_control via sysfs
- CC netdev mailing list
Changes v3:
- Add Andrew review tag
- Use SPEED_UNKNOWN to init link_speed
- Fix using HALF_DUPLEX as duplex init and use DUPLEX_UNKNOWN instead Changes v2:
- Drop ACTIVITY patch as it can be handled internally in the LED driver
- Reduce duplicate code and move the link state to a dedicated helper
Christian Marangi (3):
leds: trigger: netdev: add additional specific link speed mode
leds: trigger: netdev: add additional specific link duplex mode
leds: trigger: netdev: expose hw_control status via sysfs
drivers/leds/trigger/ledtrig-netdev.c | 114 +++++++++++++++++++++++--- include/linux/leds.h | 5 ++ 2 files changed, 109 insertions(+), 10 deletions(-)
Signature · 1 line
2.40.1
PATCH v4 1/3 leds: trigger: netdev: add additional specific link speed mode
Add additional modes for specific link speed. Use ethtool APIs to get the current link speed and enable the LED accordingly. Under netdev event handler the rtnl lock is already held and is not needed to be set to access ethtool APIs.
This is especially useful for PHY and Switch that supports LEDs hw control for specific link speed. (example scenario a PHY that have 2 LED connected one green and one orange where the green is turned on with 1000mbps speed and orange is turned on with 10mpbs speed)
On mode set from sysfs we check if we have enabled split link speed mode and reject enabling generic link mode to prevent wrong and redundant configuration.
Rework logic on the set baseline state to support these new modes to select if we need to turn on or off the LED.
Add additional modes:
- link_10: Turn on LED when link speed is 10mbps
- link_100: Turn on LED when link speed is 100mbps
- link_1000: Turn on LED when link speed is 1000mbps
--- drivers/leds/trigger/ledtrig-netdev.c | 80 +++++++++++++++++++++++---- include/linux/leds.h | 3 + 2 files changed, 73 insertions(+), 10 deletions(-)
drivers/leds/trigger/ledtrig-netdev.c +70 -10
@@ -13,6 +13,7 @@#include <linux/atomic.h> #include <linux/ctype.h> #include <linux/device.h> +#include <linux/ethtool.h> #include <linux/init.h> #include <linux/jiffies.h> #include <linux/kernel.h>
@@ -21,6 +22,7 @@#include <linux/module.h> #include <linux/netdevice.h> #include <linux/mutex.h> +#include <linux/rtnetlink.h> #include <linux/timer.h> #include "../leds.h"
@@ -52,6 +54,8 @@ struct led_netdev_data {unsigned int last_activity;unsigned long mode; +int link_speed; +bool carrier_link_up;bool hw_control; };
@@ -77,7 +81,24 @@ static void set_baseline_state(struct led_netdev_data *trigger_data)if (!trigger_data->carrier_link_up) {led_set_brightness (led_cdev,LED_OFF ); }else { +bool blink_on = false; +if (test_bit (TRIGGER_NETDEV_LINK , &trigger_data->mode)) + blink_on = true; + +if (test_bit (TRIGGER_NETDEV_LINK_10 , &trigger_data->mode) && + trigger_data->link_speed ==SPEED_10 ) + blink_on = true; + +if (test_bit (TRIGGER_NETDEV_LINK_100 , &trigger_data->mode) && + trigger_data->link_speed ==SPEED_100 ) + blink_on = true; + +if (test_bit (TRIGGER_NETDEV_LINK_1000 , &trigger_data->mode) && + trigger_data->link_speed ==SPEED_1000 ) + blink_on = true; + +if (blink_on)led_set_brightness (led_cdev, led_cdev->blink_brightness);else
@@ -161,6 +182,18 @@ static bool can_hw_control(struct led_netdev_data *trigger_data)return true; } +static void get_device_state (struct led_netdev_data *trigger_data) +{ +struct ethtool_link_ksettings cmd; + + trigger_data->carrier_link_up =netif_carrier_ok (trigger_data->net_dev); +if (!trigger_data->carrier_link_up) +return ; + +if (!__ethtool_get_link_ksettings (trigger_data->net_dev, &cmd)) + trigger_data->link_speed = cmd.base.speed; +} +static ssize_t device_name_show (struct device *dev,struct device_attribute *attr,char *buf) {
@@ -196,8 +229,12 @@ static int set_device_name(struct led_netdev_data *trigger_data,dev_get_by_name (&init_net, trigger_data->device_name); trigger_data->carrier_link_up = false; -if (trigger_data->net_dev !=NULL ) - trigger_data->carrier_link_up =netif_carrier_ok (trigger_data->net_dev); + trigger_data->link_speed =SPEED_UNKNOWN ; +if (trigger_data->net_dev !=NULL ) { +rtnl_lock (); +get_device_state (trigger_data); +rtnl_unlock (); + } trigger_data->last_activity =0 ;
@@ -234,6 +271,9 @@ static ssize_t netdev_led_attr_show(struct device *dev, char *buf,switch (attr) {case TRIGGER_NETDEV_LINK : +case TRIGGER_NETDEV_LINK_10 : +case TRIGGER_NETDEV_LINK_100 : +case TRIGGER_NETDEV_LINK_1000 :case TRIGGER_NETDEV_TX :case TRIGGER_NETDEV_RX : bit = attr;
@@ -249,7 +289,7 @@ static ssize_t netdev_led_attr_store(struct device *dev, const char *buf, size_t size, enum led_trigger_netdev_modes attr) {struct led_netdev_data *trigger_data =led_trigger_get_drvdata (dev); -unsigned long state; +unsigned long state, mode = trigger_data->mode;int ret;int bit;
@@ -259,6 +299,9 @@ static ssize_t netdev_led_attr_store(struct device *dev, const char *buf,switch (attr) {case TRIGGER_NETDEV_LINK : +case TRIGGER_NETDEV_LINK_10 : +case TRIGGER_NETDEV_LINK_100 : +case TRIGGER_NETDEV_LINK_1000 :case TRIGGER_NETDEV_TX :case TRIGGER_NETDEV_RX : bit = attr;
@@ -267,13 +310,20 @@ static ssize_t netdev_led_attr_store(struct device *dev, const char *buf,return -EINVAL ; } -cancel_delayed_work_sync (&trigger_data->work); -if (state) -set_bit (bit, &trigger_data->mode); +set_bit (bit, &mode);else -clear_bit (bit, &trigger_data->mode); +clear_bit (bit, &mode); + +if (test_bit (TRIGGER_NETDEV_LINK , &mode) && + (test_bit (TRIGGER_NETDEV_LINK_10 , &mode) || +test_bit (TRIGGER_NETDEV_LINK_100 , &mode) || +test_bit (TRIGGER_NETDEV_LINK_1000 , &mode))) +return -EINVAL ; + +cancel_delayed_work_sync (&trigger_data->work); + trigger_data->mode = mode; trigger_data->hw_control =can_hw_control (trigger_data);set_baseline_state (trigger_data);
@@ -295,6 +345,9 @@ static ssize_t netdev_led_attr_store(struct device *dev, const char *buf,static DEVICE_ATTR_RW (trigger_name)DEFINE_NETDEV_TRIGGER (link, TRIGGER_NETDEV_LINK); +DEFINE_NETDEV_TRIGGER (link_10,TRIGGER_NETDEV_LINK_10 ); +DEFINE_NETDEV_TRIGGER (link_100,TRIGGER_NETDEV_LINK_100 ); +DEFINE_NETDEV_TRIGGER (link_1000,TRIGGER_NETDEV_LINK_1000 );DEFINE_NETDEV_TRIGGER (tx,TRIGGER_NETDEV_TX );DEFINE_NETDEV_TRIGGER (rx,TRIGGER_NETDEV_RX );
@@ -338,6 +391,9 @@ static DEVICE_ATTR_RW(interval);static struct attribute *netdev_trig_attrs[] = { &dev_attr_device_name.attr, &dev_attr_link.attr, + &dev_attr_link_10.attr, + &dev_attr_link_100.attr, + &dev_attr_link_1000.attr, &dev_attr_rx.attr, &dev_attr_tx.attr, &dev_attr_interval.attr,
@@ -368,9 +424,10 @@ static int netdev_trig_notify(struct notifier_block *nb,mutex_lock (&trigger_data->lock); trigger_data->carrier_link_up = false; + trigger_data->link_speed =SPEED_UNKNOWN ;switch (evt) {case NETDEV_CHANGENAME : - trigger_data->carrier_link_up =netif_carrier_ok (dev); +get_device_state (trigger_data); fallthrough;case NETDEV_REGISTER :dev_put (trigger_data->net_dev);
@@ -383,7 +440,7 @@ static int netdev_trig_notify(struct notifier_block *nb,break ;case NETDEV_UP :case NETDEV_CHANGE : - trigger_data->carrier_link_up =netif_carrier_ok (dev); +get_device_state (trigger_data);break ; }
@@ -426,7 +483,10 @@ static void netdev_trig_work(struct work_struct *work)if (trigger_data->last_activity != new_activity) {led_stop_software_blink (trigger_data->led_cdev); - invert =test_bit (TRIGGER_NETDEV_LINK , &trigger_data->mode); + invert =test_bit (TRIGGER_NETDEV_LINK , &trigger_data->mode) || +test_bit (TRIGGER_NETDEV_LINK_10 , &trigger_data->mode) || +test_bit (TRIGGER_NETDEV_LINK_100 , &trigger_data->mode) || +test_bit (TRIGGER_NETDEV_LINK_1000 , &trigger_data->mode); interval =jiffies_to_msecs (atomic_read (&trigger_data->interval));/* base state is ON (link present) */
include/linux/leds.h +3 -0
@@ -582,6 +582,9 @@ static inline void *led_get_trigger_data(struct led_classdev *led_cdev)/* Trigger specific enum */ enum led_trigger_netdev_modes {TRIGGER_NETDEV_LINK =0 , +TRIGGER_NETDEV_LINK_10 , +TRIGGER_NETDEV_LINK_100 , +TRIGGER_NETDEV_LINK_1000 ,TRIGGER_NETDEV_TX ,TRIGGER_NETDEV_RX ,
Signature · 1 line
2.40.1
PATCH v4 2/3 leds: trigger: netdev: add additional specific link duplex mode
In reply to Christian MarangiAdd additional modes for specific link duplex. Use ethtool APIs to get the current link duplex and enable the LED accordingly. Under netdev event handler the rtnl lock is already held and is not needed to be set to access ethtool APIs.
This is especially useful for PHY and Switch that supports LEDs hw control for specific link duplex.
Add additional modes:
- half_duplex: Turn on LED when link is half duplex
- full_duplex: Turn on LED when link is full duplex
--- drivers/leds/trigger/ledtrig-netdev.c | 27 +++++++++++++++++++++++++-- include/linux/leds.h | 2 ++ 2 files changed, 27 insertions(+), 2 deletions(-)
drivers/leds/trigger/ledtrig-netdev.c +25 -2
@@ -55,6 +55,7 @@ struct led_netdev_data {unsigned long mode;int link_speed; +u8 duplex;bool carrier_link_up;bool hw_control;
@@ -98,6 +99,14 @@ static void set_baseline_state(struct led_netdev_data *trigger_data) trigger_data->link_speed == SPEED_1000) blink_on = true; +if (test_bit (TRIGGER_NETDEV_HALF_DUPLEX , &trigger_data->mode) && + trigger_data->duplex ==DUPLEX_HALF ) + blink_on = true; + +if (test_bit (TRIGGER_NETDEV_FULL_DUPLEX , &trigger_data->mode) && + trigger_data->duplex ==DUPLEX_FULL ) + blink_on = true; +if (blink_on)led_set_brightness (led_cdev, led_cdev->blink_brightness);
@@ -190,8 +199,10 @@ static void get_device_state(struct led_netdev_data *trigger_data)if (!trigger_data->carrier_link_up)return ; -if (!__ethtool_get_link_ksettings (trigger_data->net_dev, &cmd)) +if (!__ethtool_get_link_ksettings (trigger_data->net_dev, &cmd)) { trigger_data->link_speed = cmd.base.speed; + trigger_data->duplex = cmd.base.duplex; + } } static ssize_t device_name_show(struct device *dev,
@@ -230,6 +241,7 @@ static int set_device_name(struct led_netdev_data *trigger_data, trigger_data->carrier_link_up = false; trigger_data->link_speed =SPEED_UNKNOWN ; + trigger_data->duplex =DUPLEX_UNKNOWN ;if (trigger_data->net_dev !=NULL ) {rtnl_lock ();get_device_state (trigger_data);
@@ -274,6 +286,8 @@ static ssize_t netdev_led_attr_show(struct device *dev, char *buf,case TRIGGER_NETDEV_LINK_10 :case TRIGGER_NETDEV_LINK_100 :case TRIGGER_NETDEV_LINK_1000 : +case TRIGGER_NETDEV_HALF_DUPLEX : +case TRIGGER_NETDEV_FULL_DUPLEX :case TRIGGER_NETDEV_TX :case TRIGGER_NETDEV_RX : bit = attr;
@@ -302,6 +316,8 @@ static ssize_t netdev_led_attr_store(struct device *dev, const char *buf,case TRIGGER_NETDEV_LINK_10 :case TRIGGER_NETDEV_LINK_100 :case TRIGGER_NETDEV_LINK_1000 : +case TRIGGER_NETDEV_HALF_DUPLEX : +case TRIGGER_NETDEV_FULL_DUPLEX :case TRIGGER_NETDEV_TX :case TRIGGER_NETDEV_RX : bit = attr;
@@ -348,6 +364,8 @@ DEFINE_NETDEV_TRIGGER(link, TRIGGER_NETDEV_LINK);DEFINE_NETDEV_TRIGGER (link_10,TRIGGER_NETDEV_LINK_10 );DEFINE_NETDEV_TRIGGER (link_100,TRIGGER_NETDEV_LINK_100 );DEFINE_NETDEV_TRIGGER (link_1000,TRIGGER_NETDEV_LINK_1000 ); +DEFINE_NETDEV_TRIGGER (half_duplex,TRIGGER_NETDEV_HALF_DUPLEX ); +DEFINE_NETDEV_TRIGGER (full_duplex,TRIGGER_NETDEV_FULL_DUPLEX );DEFINE_NETDEV_TRIGGER (tx,TRIGGER_NETDEV_TX );DEFINE_NETDEV_TRIGGER (rx,TRIGGER_NETDEV_RX );
@@ -394,6 +412,8 @@ static struct attribute *netdev_trig_attrs[] = { &dev_attr_link_10.attr, &dev_attr_link_100.attr, &dev_attr_link_1000.attr, + &dev_attr_full_duplex.attr, + &dev_attr_half_duplex.attr, &dev_attr_rx.attr, &dev_attr_tx.attr, &dev_attr_interval.attr,
@@ -425,6 +445,7 @@ static int netdev_trig_notify(struct notifier_block *nb, trigger_data->carrier_link_up = false; trigger_data->link_speed =SPEED_UNKNOWN ; + trigger_data->duplex =DUPLEX_UNKNOWN ;switch (evt) {case NETDEV_CHANGENAME :get_device_state (trigger_data);
@@ -486,7 +507,9 @@ static void netdev_trig_work(struct work_struct *work) invert =test_bit (TRIGGER_NETDEV_LINK , &trigger_data->mode) ||test_bit (TRIGGER_NETDEV_LINK_10 , &trigger_data->mode) ||test_bit (TRIGGER_NETDEV_LINK_100 , &trigger_data->mode) || -test_bit (TRIGGER_NETDEV_LINK_1000 , &trigger_data->mode); +test_bit (TRIGGER_NETDEV_LINK_1000 , &trigger_data->mode) || +test_bit (TRIGGER_NETDEV_HALF_DUPLEX , &trigger_data->mode) || +test_bit (TRIGGER_NETDEV_FULL_DUPLEX , &trigger_data->mode); interval =jiffies_to_msecs (atomic_read (&trigger_data->interval));/* base state is ON (link present) */
include/linux/leds.h +2 -0
@@ -585,6 +585,8 @@ enum led_trigger_netdev_modes {TRIGGER_NETDEV_LINK_10 ,TRIGGER_NETDEV_LINK_100 ,TRIGGER_NETDEV_LINK_1000 , +TRIGGER_NETDEV_HALF_DUPLEX , +TRIGGER_NETDEV_FULL_DUPLEX ,TRIGGER_NETDEV_TX , TRIGGER_NETDEV_RX,
Signature · 1 line
2.40.1
Re: [net-next PATCH v4 2/3] leds: trigger: netdev: add additional specific link duplex mode
Quoted 5 lines · Christian Marangi
Add additional modes for specific link duplex. Use ethtool APIs to get the current link duplex and enable the LED accordingly. Under netdev event handler the rtnl lock is already held and is not needed to be set to access ethtool APIs.
Quoted 8 lines
This is especially useful for PHY and Switch that supports LEDs hw control for specific link duplex.
Add additional modes:
-half_duplex: Turn on LED when link is half duplex
-full_duplex: Turn on LED when link is full duplexSigned-off-by Christian Marangi <[email protected]>
Andrew
PATCH v4 3/3 leds: trigger: netdev: expose hw_control status via sysfs
In reply to Christian MarangiExpose hw_control status via sysfs for the netdev trigger to give userspace better understanding of the current state of the trigger and the LED.
--- drivers/leds/trigger/ledtrig-netdev.c | 11 +++++++++++ 1 file changed, 11 insertions(+)
drivers/leds/trigger/ledtrig-netdev.c +11 -0
@@ -406,6 +406,16 @@ static ssize_t interval_store(struct device *dev,static DEVICE_ATTR_RW (interval); +static ssize_t hw_control_show (struct device *dev, +struct device_attribute *attr,char *buf) +{ +struct led_netdev_data *trigger_data =led_trigger_get_drvdata (dev); + +return sprintf (buf,"%d\n" , trigger_data->hw_control); +} + +static DEVICE_ATTR_RO (hw_control); +static struct attribute *netdev_trig_attrs[] = { &dev_attr_device_name.attr, &dev_attr_link.attr,
@@ -417,6 +427,7 @@ static struct attribute *netdev_trig_attrs[] = { &dev_attr_rx.attr, &dev_attr_tx.attr, &dev_attr_interval.attr, + &dev_attr_hw_control.attr, NULL };ATTRIBUTE_GROUPS (netdev_trig);
Signature · 1 line
2.40.1
Re: [net-next PATCH v4 3/3] leds: trigger: netdev: expose hw_control status via sysfs
Quoted 5 lines · Christian Marangi
Expose
hw_controlstatus via sysfs for the netdev trigger to give userspace better understanding of the current state of the trigger and the LED.Signed-off-by Christian Marangi <[email protected]>
Andrew
Lee Jones
maintainerQuoted 50 lines · Christian Marangi
This is a continue of [1]. It was decided to take a more gradual approach to implement LEDs support for switch and phy starting with basic support and then implementing the hw control part when we have all the prereq done.
This should be the final part for the netdev trigger.
I added net-next tag and added netdev mailing list since I was informed that this should be merged with netdev branch.We collect some info around and we found a good set of modes that are common in almost all the PHY and Switch.
These modes are:
- Modes for dedicated linkspeed(10, 100, 1000 mbps). Additional mode can be added later following this example.
- Modes for half and full duplex.The original idea was to add hw control only modes.
While the concept makes sense in practice it would results in lots of additional code and extra check to make sure we are setting correct modes.With the suggestion from Andrew it was pointed out that using the ethtool APIs we can actually get the current link speed and duplex and this effectively removed the problem of having hw control only modes since we can fallback to software.
Since these modes are supported by software, we can skip providing an user for this in the LED driver to support hw control for these new modes (that will come right after this is merged) and prevent this to be another multi subsystem series.
For link speed and duplex we use ethtool APIs.
To call ethtool APIs, rtnl lock is needed but this can be skipped on handling netdev events as the lock is already held.
[1] https://lore.kernel.org/lkml/[email protected]/
Changes v4:
- Add net-next tag
- Add additional patch to exposehw_controlvia sysfs
- CC netdev mailing list
Changes v3:
- Add Andrew review tag
- UseSPEED_UNKNOWNto initlink_speed
- Fix usingHALF_DUPLEXas duplex init and useDUPLEX_UNKNOWNinstead Changes v2:
- Drop ACTIVITY patch as it can be handled internally in the LED driver
- Reduce duplicate code and move the link state to a dedicated helper
Quoted 8 lines
Christian Marangi (3):
leds: trigger: netdev: add additional specific link speed mode
leds: trigger: netdev: add additional specific link duplex mode
leds: trigger: netdev: exposehw_controlstatus via sysfsdrivers/leds/trigger/ledtrig-netdev.c | 114 +++++++++++++++++++++++--- include/linux/leds.h | 5 ++ 2 files changed, 109 insertions(+), 10 deletions(-)
Seeing as we're on -rc7 already, any reason why we shouldn't hold off and simply apply these against LEDs once v6.5 is released?
Signature · 1 line
Lee Jones [李琼斯]
Quoted 2 lines
Seeing as we're on -rc7 already, any reason why we shouldn't hold off and simply apply these against LEDs once v6.5 is released?
Each subsystem has its own policies. netdev tends to accept patches right up until the merge window opens, sometimes even a couple of days into the merge window for low risk changes. Maybe this is because netdev is fast moving, two weeks of not merging results in a big backlog of patches, making it a bumpy restart once merging is started again. And is some of those late patches breaks something, there is still 7 weeks to fix it.
Since this is cross subsystems i would expect both subsystems Maintainers to agree to a merge or not. If you want to be more conservative than netdev, wait until after the next merge window, please say so.
If you do decided to wait, you are going to need to create another stable branch to pull into netdev. I know it is not a huge overhead, but it is still work, coordination etc.
Andrew
Lee Jones
maintainerQuoted 11 lines · Andrew Lunn
Quoted 2 lines
Seeing as we're on -rc7 already, any reason why we shouldn't hold off and simply apply these against LEDs once v6.5 is released?
Each subsystem has its own policies. netdev tends to accept patches right up until the merge window opens, sometimes even a couple of days into the merge window for low risk changes. Maybe this is because netdev is fast moving, two weeks of not merging results in a big backlog of patches, making it a bumpy restart once merging is started again. And is some of those late patches breaks something, there is still 7 weeks to fix it.
Quoted 8 lines
Since this is cross subsystems i would expect both subsystems Maintainers to agree to a merge or not. If you want to be more conservative than netdev, wait until after the next merge window, please say so.
If you do decided to wait, you are going to need to create another stable branch to pull into netdev. I know it is not a huge overhead, but it is still work, coordination etc.
Can you clarify you last point for me please?
Signature · 1 line
Lee Jones [李琼斯]
Quoted 5 lines
Quoted 3 lines
If you do decided to wait, you are going to need to create another stable branch to pull into netdev. I know it is not a huge overhead, but it is still work, coordination etc.
Can you clarify you last point for me please?
This patchset extends the conditions on which the trigger blinks the LED. It adds a couple more values to enum led_trigger_netdev_modes in include/linux/leds.h. Once it gets merged, i will have a followup patch extending the Marvell PHY driver to make us of them. It will need these additional enum values. I also expect other PHY drivers to gain support for them. Probably the dp83867.c driver since Alexander Stein already has a patch merged adding support for what the current API supports.
If we merge this patchset now via netdev, -rc1 should have everything we need for this continuing development work. If we wait to merge these patches until -rc1, only the LED tree has the needed patches, so these network drivers will need a stable branch we can pull into netdev.
Both ways work, we can do either. But it is probably easier for everybody to merge now via netdev.
Andrew
Lee Jones
maintainerQuoted 15 lines · Andrew Lunn
Quoted 5 lines
Quoted 3 lines
If you do decided to wait, you are going to need to create another stable branch to pull into netdev. I know it is not a huge overhead, but it is still work, coordination etc.
Can you clarify you last point for me please?
This patchset extends the conditions on which the trigger blinks the LED. It adds a couple more values to enum
led_trigger_netdev_modesininclude/linux/leds.h. Once it gets merged, i will have a followup patch extending the Marvell PHY driver to make us of them. It will need these additional enum values. I also expect other PHY drivers to gain support for them. Probably thedp83867.cdriver since Alexander Stein already has a patch merged adding support for what the current API supports.
Quoted 8 lines
If we merge this patchset now via netdev, -rc1 should have everything we need for this continuing development work. If we wait to merge these patches until -rc1, only the LED tree has the needed patches, so these network drivers will need a stable branch we can pull into netdev.
Both ways work, we can do either. But it is probably easier for everybody to merge now via netdev.
Got it, thanks.
Signature · 1 line
Lee Jones [李琼斯]
Quoted 31 lines · Christian Marangi
This is a continue of [1]. It was decided to take a more gradual approach to implement LEDs support for switch and phy starting with basic support and then implementing the hw control part when we have all the prereq done.
This should be the final part for the netdev trigger.
I added net-next tag and added netdev mailing list since I was informed that this should be merged with netdev branch.We collect some info around and we found a good set of modes that are common in almost all the PHY and Switch.
These modes are:
- Modes for dedicated linkspeed(10, 100, 1000 mbps). Additional mode can be added later following this example.
- Modes for half and full duplex.The original idea was to add hw control only modes.
While the concept makes sense in practice it would results in lots of additional code and extra check to make sure we are setting correct modes.With the suggestion from Andrew it was pointed out that using the ethtool APIs we can actually get the current link speed and duplex and this effectively removed the problem of having hw control only modes since we can fallback to software.
Since these modes are supported by software, we can skip providing an user for this in the LED driver to support hw control for these new modes (that will come right after this is merged) and prevent this to be another multi subsystem series.
Quoted 6 lines
For link speed and duplex we use ethtool APIs.
To call ethtool APIs, rtnl lock is needed but this can be skipped on handling netdev events as the lock is already held.
Hi Christian,
I am sorry if I am missing something obvious here, but this series does not appear to apply on top of net-next.
Please consider rebasing and reposting.
As you probably know, you can include the reviewed-by tags provided by Andrew for this posting, unless there are substantial changes.
Signature · 1 line
pw-bot: changes-requested
Quoted 41 lines · Simon Horman
Quoted 31 lines · Christian Marangi
This is a continue of [1]. It was decided to take a more gradual approach to implement LEDs support for switch and phy starting with basic support and then implementing the hw control part when we have all the prereq done.
This should be the final part for the netdev trigger.
I added net-next tag and added netdev mailing list since I was informed that this should be merged with netdev branch.We collect some info around and we found a good set of modes that are common in almost all the PHY and Switch.
These modes are:
- Modes for dedicated linkspeed(10, 100, 1000 mbps). Additional mode can be added later following this example.
- Modes for half and full duplex.The original idea was to add hw control only modes.
While the concept makes sense in practice it would results in lots of additional code and extra check to make sure we are setting correct modes.With the suggestion from Andrew it was pointed out that using the ethtool APIs we can actually get the current link speed and duplex and this effectively removed the problem of having hw control only modes since we can fallback to software.
Since these modes are supported by software, we can skip providing an user for this in the LED driver to support hw control for these new modes (that will come right after this is merged) and prevent this to be another multi subsystem series.
Quoted 6 lines
For link speed and duplex we use ethtool APIs.
To call ethtool APIs, rtnl lock is needed but this can be skipped on handling netdev events as the lock is already held.
Hi Christian,
Quoted 12 lines
I am sorry if I am missing something obvious here, but this series does not appear to apply on top of net-next.
Please consider rebasing and reposting.
As you probably know, you can include the reviewed-by tags provided by Andrew for this posting, unless there are substantial changes.
Signature · 1 line
pw-bot: changes-requested
Hi, sorry for the mistake. I just sent v5 and added the additional Review-by tag.
Signature · 1 line
Ansuel