doc: imx8mp_evk: Remove unneeded export ATF_LOAD_ADDR line
Fabio Estevam
reviewerPATCH 1/2 doc: imx8mp_evk: Remove unneeded export ATF_LOAD_ADDR line
From: Fabio Estevam <[email protected]>
Originally, exporting the ATF_LOAD_ADDR was required, but since binman has been used to generate the flash.bin, it is no longer needed to do such manual export.
The ATF address is now passed via binman in imx8mp-u-boot.dtsi:
atf {
description = "ARM Trusted Firmware";
type = "firmware";
arch = "arm64";
compression = "none";
load = <0x970000>;
entry = <0x970000>;
atf_blob: atf-blob {
filename = "bl31.bin";
type = "atf-bl31";
};
};Remove the unneeded export ATF_LOAD_ADDR line.
--- doc/board/nxp/imx8mp_evk.rst | 1 - 1 file changed, 1 deletion(-)
doc/board/nxp/imx8mp_evk.rst +0 -1
@@ -44,7 +44,6 @@ Build U-Boot $ cp ../firmware-imx-8.10/firmware/ddr/synopsys/lpddr4_pmu_train_1d_imem_202006.bin ./build/ $ cp ../firmware-imx-8.10/firmware/ddr/synopsys/lpddr4_pmu_train_2d_dmem_202006.bin ./build/ $ cp ../firmware-imx-8.10/firmware/ddr/synopsys/lpddr4_pmu_train_2d_imem_202006.bin ./build/ - $ export ATF_LOAD_ADDR=0x970000 $ make O=build Burn the flash.bin to the MicroSD card at offset 32KB:
Signature · 1 line
2.34.1
Fabio Estevam
reviewerPATCH 2/2 doc: imx8mp_evk: Use in-tree build in the example
From: Fabio Estevam <[email protected]>
To make it consistent with the instructions from other NXP imx8m boards, such as imx8mm-evk and imx8mn-evk, use U-Boot in-tree build in the examples.
--- doc/board/nxp/imx8mp_evk.rst | 16 +++++++++------- 1 file changed, 9 insertions(+), 7 deletions(-)
doc/board/nxp/imx8mp_evk.rst +9 -7
@@ -37,20 +37,22 @@ Build U-Boot .. code-block:: bash +Note: builddir is U-Boot build directory (source directory for in-tree builds). + $ export CROSS_COMPILE=aarch64-poky-linux- $ make O=build imx8mp_evk_defconfig - $ cp ../imx-atf/build/imx8mp/release/bl31.bin ./build/bl31.bin - $ cp ../firmware-imx-8.10/firmware/ddr/synopsys/lpddr4_pmu_train_1d_dmem_202006.bin ./build/ - $ cp ../firmware-imx-8.10/firmware/ddr/synopsys/lpddr4_pmu_train_1d_imem_202006.bin ./build/ - $ cp ../firmware-imx-8.10/firmware/ddr/synopsys/lpddr4_pmu_train_2d_dmem_202006.bin ./build/ - $ cp ../firmware-imx-8.10/firmware/ddr/synopsys/lpddr4_pmu_train_2d_imem_202006.bin ./build/ - $ make O=build + $ cp ../imx-atf/build/imx8mp/release/bl31.bin $(builddir) + $ cp ../firmware-imx-8.10/firmware/ddr/synopsys/lpddr4_pmu_train_1d_dmem_202006.bin $(builddir) + $ cp ../firmware-imx-8.10/firmware/ddr/synopsys/lpddr4_pmu_train_1d_imem_202006.bin $(builddir) + $ cp ../firmware-imx-8.10/firmware/ddr/synopsys/lpddr4_pmu_train_2d_dmem_202006.bin $(builddir) + $ cp ../firmware-imx-8.10/firmware/ddr/synopsys/lpddr4_pmu_train_2d_imem_202006.bin $(builddir) + $ make Burn the flash.bin to the MicroSD card at offset 32KB: .. code-block:: bash - $sudo dd if=build/flash.bin of=/dev/sd[x] bs=1K seek=32 conv=notrunc; sync + $ sudo dd if=flash.bin of=/dev/sd[x] bs=1K seek=32 conv=notrunc; sync Boot ----
Signature · 1 line
2.34.1
Re: [PATCH 2/2] doc: imx8mp_evk: Use in-tree build in the example
Quoted 7 lines · Fabio Estevam
From: Fabio Estevam<[email protected]>
To make it consistent with the instructions from other NXP imx8m boards, such as imx8mm-evk and imx8mn-evk, use U-Boot in-tree build in the examples.
Signed-off-by Fabio Estevam<[email protected]>
Quoted 22 lines · Fabio Estevam
From: Fabio Estevam<[email protected]>
Originally, exporting the
ATF_LOAD_ADDRwas required, but since binman has been used to generate the flash.bin, it is no longer needed to do such manual export.The ATF address is now passed via binman in
imx8mp-u-boot.dtsi:atf { description = "ARM Trusted Firmware"; type = "firmware"; arch = "arm64"; compression = "none"; load = <0x970000>; entry = <0x970000>; atf_blob: atf-blob { filename = "bl31.bin"; type = "atf-bl31"; }; };
Quoted 3 lines
Remove the unneeded export
ATF_LOAD_ADDRline.Signed-off-by Fabio Estevam<[email protected]>