dwc general suspend/resume functionality
Subsystems (5)
Frank Li
maintainerv10 cover dwc general suspend/resume functionality
Change log
- Change from v9 to v10
min change according to Mani's feedback
Add Mani's ACK tag
- Change from v8 to v9
- Change from v7 to v8
Add new patch to add common PCIE_PME_TO_L2_TIMEOUT_US define. timeout value using PCIE_PME_TO_L2_TIMEOUT_US.
- Chnage from v6 to v7
Remove local varible struct dw_pcie *pci = pcie->pci Change according to Manivannan's feedback
remove unused lut_off and lut_base
fixed 100 to 1000(for 1ms)
using dev_err for timeout
refine commit message
fix sleep value 100 (should be 1000 for 1ms). use dev_err when timeout
- Change from v5 to v6
change to NOIRQ_SYSTEM_SLEEP_PM_OPS to remove #ifdef PM_CONFIG refine commit message
change according to Manivannan's comments.
remove reduncate step dw_pcie_set_dstate()
return 0 when .pme_turn_off is zero
call host_deinit() in suspend
check .host_deinit and .host_init point before call.
- Change from v4 to v5
- Change from v3 to v4
change according to Manivannan's comments.
- change at v2 to v3
Basic rewrite whole patch according rob herry suggestion. put common function into dwc, so more soc can share the same logic.
Frank Li (2):
PCI: Add macro PCIE_PME_TO_L2_TIMEOUT_US
PCI: dwc: Implement general suspend/resume functionality for L2/L3
transitions
Hou Zhiqiang (1):
PCI: layerscape: Add power management support for ls1028a
drivers/pci/controller/dwc/pci-layerscape.c | 130 ++++++++++++++++-- .../pci/controller/dwc/pcie-designware-host.c | 76 ++++++++++ drivers/pci/controller/dwc/pcie-designware.h | 28 ++++ drivers/pci/pci.h | 6 + 4 files changed, 231 insertions(+), 9 deletions(-)
Signature · 1 line
2.34.1
Frank Li
maintainerPATCH v10 1/3 PCI: Add macro PCIE_PME_TO_L2_TIMEOUT_US
Introduce the PCIE_PME_TO_L2_TIMEOUT_US macro to facilitate checking the L2 ready timeout in the PCI subsystem.
--- drivers/pci/pci.h | 6 ++++++ 1 file changed, 6 insertions(+)
drivers/pci/pci.h +6 -0
@@ -13,6 +13,12 @@#define PCIE_LINK_RETRAIN_TIMEOUT_MS 1000 +/* +* PCIe r6.0, sec 5.3.3.2.1 <PME Synchronization> +* Recommends 1ms to 10ms timeout to check L2 ready. +*/ +#define PCIE_PME_TO_L2_TIMEOUT_US 10000 +extern const unsigned char pcie_link_speed[];extern bool pci_early_dump;
Signature · 1 line
2.34.1
Frank Li
maintainerPATCH v10 2/3 PCI: dwc: Implement general suspend/resume functionality for L2/L3 transitions
In reply to Frank LiIntroduce helper function dw_pcie_get_ltssm() to retrieve SMLH_LTSS_STATE.
Add callback .pme_turn_off and .exit_from_l2 for platform specific PME handling.
Add common dw_pcie_suspend(resume)_noirq() API to avoid duplicated code in dwc pci host controller platform driver.
Typical L2 entry workflow/dw_pcie_suspend_noirq()
1. Transmit PME turn off signal to PCI devices and wait for PME_To_Ack.
2. Await link entering L2_IDLE state.
Typical L2 exit workflow/dw_pcie_resume_noirq()
1. Issue exit from L2 command.
2. Reinitialize PCI host.
3. Wait for link to become active.
--- .../pci/controller/dwc/pcie-designware-host.c | 76 +++++++++++++++++++ drivers/pci/controller/dwc/pcie-designware.h | 29 +++++++ 2 files changed, 105 insertions(+)
drivers/pci/controller/dwc/pcie-designware-host.c +76 -0
@@ -8,6 +8,7 @@* Author: Jingoo Han <[email protected]> */ +#include <linux/iopoll.h> #include <linux/irqchip/chained_irq.h> #include <linux/irqdomain.h> #include <linux/msi.h>
@@ -16,6 +17,7 @@#include <linux/pci_regs.h> #include <linux/platform_device.h> +#include "../../pci.h" #include "pcie-designware.h" static struct pci_ops dw_pcie_ops;
@@ -807,3 +809,77 @@ int dw_pcie_setup_rc(struct dw_pcie_rp *pp)return 0 ; }EXPORT_SYMBOL_GPL (dw_pcie_setup_rc); + +int dw_pcie_suspend_noirq (struct dw_pcie *pci) +{ +u8 offset =dw_pcie_find_capability (pci,PCI_CAP_ID_EXP ); +u32 val; +int ret; + +/* +* If L1SS is supported, then do not put the link into L2 as some +* devices such as NVMe expect low resume latency. +*/ +if (dw_pcie_readw_dbi (pci, offset +PCI_EXP_LNKCTL ) &PCI_EXP_LNKCTL_ASPM_L1 ) +return 0 ; + +if (dw_pcie_get_ltssm (pci) <=DW_PCIE_LTSSM_DETECT_ACT ) +return 0 ; + +if (!pci->pp.ops->pme_turn_off) +return 0 ; + + pci->pp.ops->pme_turn_off (&pci->pp); + + ret =read_poll_timeout (dw_pcie_get_ltssm, val, val ==DW_PCIE_LTSSM_L2_IDLE , +PCIE_PME_TO_L2_TIMEOUT_US /10 , +PCIE_PME_TO_L2_TIMEOUT_US , false, pci); +if (ret) { +dev_err (pci->dev,"Timeout waiting for L2 entry! LTSSM: 0x%x\n" , val); +return ret; + } + +if (pci->pp.ops->host_deinit) + pci->pp.ops->host_deinit (&pci->pp); + + pci->suspended = true; + +return ret; +} +EXPORT_SYMBOL_GPL (dw_pcie_suspend_noirq); + +int dw_pcie_resume_noirq (struct dw_pcie *pci) +{ +int ret; + +if (!pci->suspended) +return 0 ; + + pci->suspended = false; + +if (!pci->pp.ops->exit_from_l2) +return 0 ; + + pci->pp.ops->exit_from_l2 (&pci->pp); + +if (pci->pp.ops->host_init) { + ret = pci->pp.ops->host_init (&pci->pp); +if (ret) { +dev_err (pci->dev,"Host init failed: %d\n" , ret); +return ret; + } + } + +dw_pcie_setup_rc (&pci->pp); + + ret =dw_pcie_start_link (pci); +if (ret) +return ret; + + ret =dw_pcie_wait_for_link (pci); +if (ret) +return ret; + +return ret; +} +EXPORT_SYMBOL_GPL (dw_pcie_resume_noirq);
drivers/pci/controller/dwc/pcie-designware.h +29 -0
@@ -288,10 +288,22 @@ enum dw_pcie_core_rst {DW_PCIE_NUM_CORE_RSTS }; +enum dw_pcie_ltssm { +/* Need to align with PCIE_PORT_DEBUG0 bits 0:5 */ +DW_PCIE_LTSSM_DETECT_QUIET =0x0 , +DW_PCIE_LTSSM_DETECT_ACT =0x1 , +DW_PCIE_LTSSM_L0 =0x11 , +DW_PCIE_LTSSM_L2_IDLE =0x15 , + +DW_PCIE_LTSSM_UNKNOWN =0xFFFFFFFF , +}; +struct dw_pcie_host_ops {int (*host_init)(struct dw_pcie_rp *pp);void (*host_deinit)(struct dw_pcie_rp *pp);int (*msi_host_init)(struct dw_pcie_rp *pp); +void (*pme_turn_off)(struct dw_pcie_rp *pp); +void (*exit_from_l2)(struct dw_pcie_rp *pp); };struct dw_pcie_rp {
@@ -364,6 +376,7 @@ struct dw_pcie_ops {void (*write_dbi2)(struct dw_pcie *pcie,void __iomem *base,u32 reg,size_t size,u32 val);int (*link_up)(struct dw_pcie *pcie); +enum dw_pcie_ltssm (*get_ltssm)(struct dw_pcie *pcie);int (*start_link)(struct dw_pcie *pcie);void (*stop_link)(struct dw_pcie *pcie); };
@@ -393,6 +406,7 @@ struct dw_pcie {struct reset_control_bulk_data app_rsts[DW_PCIE_NUM_APP_RSTS ];struct reset_control_bulk_data core_rsts[DW_PCIE_NUM_CORE_RSTS ];struct gpio_desc *pe_rst; +bool suspended; };#define to_dw_pcie_from_pp (port) container_of((port), struct dw_pcie, pp)
@@ -430,6 +444,9 @@ void dw_pcie_iatu_detect(struct dw_pcie *pci);int dw_pcie_edma_detect (struct dw_pcie *pci);void dw_pcie_edma_remove (struct dw_pcie *pci); +int dw_pcie_suspend_noirq (struct dw_pcie *pci); +int dw_pcie_resume_noirq (struct dw_pcie *pci); +static inline void dw_pcie_writel_dbi (struct dw_pcie *pci,u32 reg,u32 val) {dw_pcie_write_dbi (pci, reg,0x4 , val);
@@ -501,6 +518,18 @@ static inline void dw_pcie_stop_link(struct dw_pcie *pci) pci->ops->stop_link (pci); } +static inline enum dw_pcie_ltssm dw_pcie_get_ltssm (struct dw_pcie *pci) +{ +u32 val; + +if (pci->ops && pci->ops->get_ltssm) +return pci->ops->get_ltssm (pci); + + val =dw_pcie_readl_dbi (pci,PCIE_PORT_DEBUG0 ); + +return (enum dw_pcie_ltssm )FIELD_GET (PORT_LOGIC_LTSSM_STATE_MASK , val); +} +#ifdef CONFIG_PCIE_DW_HOST irqreturn_t dw_handle_msi_irq (struct dw_pcie_rp *pp);int dw_pcie_setup_rc (struct dw_pcie_rp *pp);
Signature · 1 line
2.34.1
Frank Li
maintainerPATCH v10 3/3 PCI: layerscape: Add power management support for ls1028a
In reply to Frank LiFrom: Hou Zhiqiang <[email protected]>
Add PME_Turn_off/PME_TO_Ack handshake sequence for ls1028a platform. Call common dwc dw_pcie_suspend(resume)_noirq() function when system enter/exit suspend state.
--- drivers/pci/controller/dwc/pci-layerscape.c | 130 ++++++++++++++++++-- 1 file changed, 121 insertions(+), 9 deletions(-)
drivers/pci/controller/dwc/pci-layerscape.c +121 -9
@@ -8,9 +8,11 @@* Author: Minghuan Lian <[email protected]> */ +#include <linux/delay.h> #include <linux/kernel.h> #include <linux/interrupt.h> #include <linux/init.h> +#include <linux/iopoll.h> #include <linux/of_pci.h> #include <linux/of_platform.h> #include <linux/of_address.h>
@@ -20,6 +22,7 @@#include <linux/mfd/syscon.h> #include <linux/regmap.h> +#include "../../pci.h" #include "pcie-designware.h" /* PEX Internal Configuration Registers */
@@ -27,12 +30,26 @@#define PCIE_ABSERR 0x8d0/* Bridge Slave Error Response Register */ #define PCIE_ABSERR_SETTING 0x9401/* Forward error of non-posted request */ +/* PF Message Command Register */ +#define LS_PCIE_PF_MCR 0x2c +#define PF_MCR_PTOMR BIT(0) +#define PF_MCR_EXL2S BIT(1) +#define PCIE_IATU_NUM 6 +struct ls_pcie_drvdata { +const u32 pf_off; +bool pm_support; +}; +struct ls_pcie {struct dw_pcie *pci; +const struct ls_pcie_drvdata *drvdata; +void __iomem *pf_base; +bool big_endian; }; +#define ls_pcie_pf_readl_addr (addr) ls_pcie_pf_readl(pcie, addr)#define to_ls_pcie (x) dev_get_drvdata((x)->dev)static bool ls_pcie_is_bridge (struct ls_pcie *pcie)
@@ -73,6 +90,60 @@ static void ls_pcie_fix_error_response(struct ls_pcie *pcie)iowrite32 (PCIE_ABSERR_SETTING , pci->dbi_base +PCIE_ABSERR ); } +static u32 ls_pcie_pf_readl (struct ls_pcie *pcie,u32 off) +{ +if (pcie->big_endian) +return ioread32be (pcie->pf_base + off); + +return ioread32 (pcie->pf_base + off); +} + +static void ls_pcie_pf_writel (struct ls_pcie *pcie,u32 off,u32 val) +{ +if (pcie->big_endian) +iowrite32be (val, pcie->pf_base + off); +else +iowrite32 (val, pcie->pf_base + off); +} + +static void ls_pcie_send_turnoff_msg (struct dw_pcie_rp *pp) +{ +struct dw_pcie *pci =to_dw_pcie_from_pp (pp); +struct ls_pcie *pcie =to_ls_pcie (pci); +u32 val; +int ret; + + val =ls_pcie_pf_readl (pcie,LS_PCIE_PF_MCR ); + val |=PF_MCR_PTOMR ; +ls_pcie_pf_writel (pcie,LS_PCIE_PF_MCR , val); + + ret =readx_poll_timeout (ls_pcie_pf_readl_addr,LS_PCIE_PF_MCR , + val, !(val &PF_MCR_PTOMR ), +PCIE_PME_TO_L2_TIMEOUT_US /10 , +PCIE_PME_TO_L2_TIMEOUT_US ); +if (ret) +dev_err (pcie->pci->dev,"poll turn off message timeout\n" ); +} + +static void ls_pcie_exit_from_l2 (struct dw_pcie_rp *pp) +{ +struct dw_pcie *pci =to_dw_pcie_from_pp (pp); +struct ls_pcie *pcie =to_ls_pcie (pci); +u32 val; +int ret; + + val =ls_pcie_pf_readl (pcie,LS_PCIE_PF_MCR ); + val |=PF_MCR_EXL2S ; +ls_pcie_pf_writel (pcie,LS_PCIE_PF_MCR , val); + + ret =readx_poll_timeout (ls_pcie_pf_readl_addr,LS_PCIE_PF_MCR , + val, !(val &PF_MCR_EXL2S ), +PCIE_PME_TO_L2_TIMEOUT_US /10 , +PCIE_PME_TO_L2_TIMEOUT_US ); +if (ret) +dev_err (pcie->pci->dev,"poll exit L2 state timeout\n" ); +} +static int ls_pcie_host_init (struct dw_pcie_rp *pp) {struct dw_pcie *pci =to_dw_pcie_from_pp (pp);
@@ -91,18 +162,28 @@ static int ls_pcie_host_init(struct dw_pcie_rp *pp)static const struct dw_pcie_host_ops ls_pcie_host_ops = { .host_init = ls_pcie_host_init, + .pme_turn_off = ls_pcie_send_turnoff_msg, + .exit_from_l2 = ls_pcie_exit_from_l2, +}; + +static const struct ls_pcie_drvdata ls1021a_drvdata = { +}; + +static const struct ls_pcie_drvdata layerscape_drvdata = { + .pf_off =0xc0000 , + .pm_support = true, };static const struct of_device_id ls_pcie_of_match[] = { - { .compatible ="fsl,ls1012a-pcie" , }, - { .compatible ="fsl,ls1021a-pcie" , }, - { .compatible ="fsl,ls1028a-pcie" , }, - { .compatible ="fsl,ls1043a-pcie" , }, - { .compatible ="fsl,ls1046a-pcie" , }, - { .compatible ="fsl,ls2080a-pcie" , }, - { .compatible ="fsl,ls2085a-pcie" , }, - { .compatible ="fsl,ls2088a-pcie" , }, - { .compatible ="fsl,ls1088a-pcie" , }, + { .compatible ="fsl,ls1012a-pcie" , .data = &layerscape_drvdata }, + { .compatible ="fsl,ls1021a-pcie" , .data = &ls1021a_drvdata }, + { .compatible ="fsl,ls1028a-pcie" , .data = &layerscape_drvdata }, + { .compatible ="fsl,ls1043a-pcie" , .data = &ls1021a_drvdata }, + { .compatible ="fsl,ls1046a-pcie" , .data = &layerscape_drvdata }, + { .compatible ="fsl,ls2080a-pcie" , .data = &layerscape_drvdata }, + { .compatible ="fsl,ls2085a-pcie" , .data = &layerscape_drvdata }, + { .compatible ="fsl,ls2088a-pcie" , .data = &layerscape_drvdata }, + { .compatible ="fsl,ls1088a-pcie" , .data = &layerscape_drvdata }, { }, };
@@ -121,6 +202,8 @@ static int ls_pcie_probe(struct platform_device *pdev)if (!pci)return -ENOMEM ; + pcie->drvdata =of_device_get_match_data (dev); + pci->dev = dev; pci->pp.ops = &ls_pcie_host_ops;
@@ -131,6 +214,10 @@ static int ls_pcie_probe(struct platform_device *pdev)if (IS_ERR (pci->dbi_base))return PTR_ERR (pci->dbi_base); + pcie->big_endian =of_property_read_bool (dev->of_node,"big-endian" ); + + pcie->pf_base = pci->dbi_base + pcie->drvdata->pf_off; +if (!ls_pcie_is_bridge (pcie))return -ENODEV ;
@@ -139,12 +226,37 @@ static int ls_pcie_probe(struct platform_device *pdev)return dw_pcie_host_init (&pci->pp); } +static int ls_pcie_suspend_noirq (struct device *dev) +{ +struct ls_pcie *pcie =dev_get_drvdata (dev); + +if (!pcie->drvdata->pm_support) +return 0 ; + +return dw_pcie_suspend_noirq (pcie->pci); +} + +static int ls_pcie_resume_noirq (struct device *dev) +{ +struct ls_pcie *pcie =dev_get_drvdata (dev); + +if (!pcie->drvdata->pm_support) +return 0 ; + +return dw_pcie_resume_noirq (pcie->pci); +} + +static const struct dev_pm_ops ls_pcie_pm_ops = { +NOIRQ_SYSTEM_SLEEP_PM_OPS (ls_pcie_suspend_noirq, ls_pcie_resume_noirq) +}; +static struct platform_driver ls_pcie_driver = { .probe = ls_pcie_probe, .driver = { .name ="layerscape-pcie" , .of_match_table = ls_pcie_of_match, .suppress_bind_attrs = true, + .pm = &ls_pcie_pm_ops, }, };builtin_platform_driver (ls_pcie_driver);
Signature · 1 line
2.34.1
Re: [PATCH v10 resent 3/3] PCI: layerscape: Add power management support for ls1028a
Quoted 110 lines · Frank Li
From: Hou Zhiqiang <[email protected]>
Add PME_Turn_off/PME_TO_Ack handshake sequence for ls1028a platform. Call common dwc dw_pcie_suspend(resume)_noirq() function when system enter/exit suspend state.
Signed-off-by Hou Zhiqiang <[email protected]>Signed-off-by Frank Li <[email protected]>--- drivers/pci/controller/dwc/pci-layerscape.c | 130 ++++++++++++++++++-- 1 file changed, 121 insertions(+), 9 deletions(-)drivers/pci/controller/dwc/pci-layerscape.c +59
-0@@ -8,9 +8,11 @@* Author: Minghuan Lian <[email protected]> */ +#include <linux/delay.h> #include <linux/kernel.h> #include <linux/interrupt.h> #include <linux/init.h> +#include <linux/iopoll.h> #include <linux/of_pci.h> #include <linux/of_platform.h> #include <linux/of_address.h> @@ -20,6 +22,7 @@#include <linux/mfd/syscon.h> #include <linux/regmap.h> +#include "../../pci.h" #include "pcie-designware.h" /* PEX Internal Configuration Registers */ @@ -27,12 +30,26 @@#define PCIE_ABSERR 0x8d0/* Bridge Slave Error Response Register */ #define PCIE_ABSERR_SETTING 0x9401/* Forward error of non-posted request */ +/* PF Message Command Register */ +#define LS_PCIE_PF_MCR 0x2c +#define PF_MCR_PTOMR BIT(0) +#define PF_MCR_EXL2S BIT(1) +#define PCIE_IATU_NUM 6 +struct ls_pcie_drvdata { +const u32 pf_off; +bool pm_support; +}; +struct ls_pcie {struct dw_pcie *pci; +const struct ls_pcie_drvdata *drvdata; +void __iomem *pf_base; +bool big_endian; }; +#define ls_pcie_pf_readl_addr (addr) ls_pcie_pf_readl(pcie, addr)#define to_ls_pcie (x) dev_get_drvdata((x)->dev)static bool ls_pcie_is_bridge (struct ls_pcie *pcie)@@ -73,6 +90,60 @@ static void ls_pcie_fix_error_response(struct ls_pcie *pcie)iowrite32 (PCIE_ABSERR_SETTING , pci->dbi_base +PCIE_ABSERR ); } +static u32 ls_pcie_pf_readl (struct ls_pcie *pcie,u32 off) +{ +if (pcie->big_endian) +return ioread32be (pcie->pf_base + off); + +return ioread32 (pcie->pf_base + off); +} + +static void ls_pcie_pf_writel (struct ls_pcie *pcie,u32 off,u32 val) +{ +if (pcie->big_endian) +iowrite32be (val, pcie->pf_base + off); +else +iowrite32 (val, pcie->pf_base + off); +} + +static void ls_pcie_send_turnoff_msg (struct dw_pcie_rp *pp) +{ +struct dw_pcie *pci =to_dw_pcie_from_pp (pp); +struct ls_pcie *pcie =to_ls_pcie (pci); +u32 val; +int ret; + + val =ls_pcie_pf_readl (pcie,LS_PCIE_PF_MCR ); + val |=PF_MCR_PTOMR ; +ls_pcie_pf_writel (pcie,LS_PCIE_PF_MCR , val); + + ret =readx_poll_timeout (ls_pcie_pf_readl_addr,LS_PCIE_PF_MCR , + val, !(val &PF_MCR_PTOMR ), +PCIE_PME_TO_L2_TIMEOUT_US /10 , +PCIE_PME_TO_L2_TIMEOUT_US ); +if (ret) +dev_err (pcie->pci->dev,"poll turn off message timeout\n" ); +} + +static void ls_pcie_exit_from_l2 (struct dw_pcie_rp *pp) +{ +struct dw_pcie *pci =to_dw_pcie_from_pp (pp); +struct ls_pcie *pcie =to_ls_pcie (pci); +u32 val; +int ret; +
drivers/pci/controller/dwc/pci-layerscape.c static void ls_pcie_fix_error_response(struct ls_pcie *pcie) · line 144
Quoted 10 lines
drivers/pci/controller/dwc/pci-layerscape.c +10
-0+ val =ls_pcie_pf_readl (pcie,LS_PCIE_PF_MCR ); + val |=PF_MCR_EXL2S ; +ls_pcie_pf_writel (pcie,LS_PCIE_PF_MCR , val); + + ret =readx_poll_timeout (ls_pcie_pf_readl_addr,LS_PCIE_PF_MCR , + val, !(val &PF_MCR_EXL2S ), +PCIE_PME_TO_L2_TIMEOUT_US /10 , +PCIE_PME_TO_L2_TIMEOUT_US ); +if (ret) +dev_err (pcie->pci->dev,"poll exit L2 state timeout\n" );
I specifically mentioned that you need to change this error message and the one below before adding my Acked-by tag. But you just added the tag without incorporating the changes :/
- Mani
Quoted 104 lines
drivers/pci/controller/dwc/pci-layerscape.c +52
-9+} +static int ls_pcie_host_init (struct dw_pcie_rp *pp) {struct dw_pcie *pci =to_dw_pcie_from_pp (pp);@@ -91,18 +162,28 @@ static int ls_pcie_host_init(struct dw_pcie_rp *pp)static const struct dw_pcie_host_ops ls_pcie_host_ops = { .host_init = ls_pcie_host_init, + .pme_turn_off = ls_pcie_send_turnoff_msg, + .exit_from_l2 = ls_pcie_exit_from_l2, +}; + +static const struct ls_pcie_drvdata ls1021a_drvdata = { +}; + +static const struct ls_pcie_drvdata layerscape_drvdata = { + .pf_off =0xc0000 , + .pm_support = true, };static const struct of_device_id ls_pcie_of_match[] = { - { .compatible ="fsl,ls1012a-pcie" , }, - { .compatible ="fsl,ls1021a-pcie" , }, - { .compatible ="fsl,ls1028a-pcie" , }, - { .compatible ="fsl,ls1043a-pcie" , }, - { .compatible ="fsl,ls1046a-pcie" , }, - { .compatible ="fsl,ls2080a-pcie" , }, - { .compatible ="fsl,ls2085a-pcie" , }, - { .compatible ="fsl,ls2088a-pcie" , }, - { .compatible ="fsl,ls1088a-pcie" , }, + { .compatible ="fsl,ls1012a-pcie" , .data = &layerscape_drvdata }, + { .compatible ="fsl,ls1021a-pcie" , .data = &ls1021a_drvdata }, + { .compatible ="fsl,ls1028a-pcie" , .data = &layerscape_drvdata }, + { .compatible ="fsl,ls1043a-pcie" , .data = &ls1021a_drvdata }, + { .compatible ="fsl,ls1046a-pcie" , .data = &layerscape_drvdata }, + { .compatible ="fsl,ls2080a-pcie" , .data = &layerscape_drvdata }, + { .compatible ="fsl,ls2085a-pcie" , .data = &layerscape_drvdata }, + { .compatible ="fsl,ls2088a-pcie" , .data = &layerscape_drvdata }, + { .compatible ="fsl,ls1088a-pcie" , .data = &layerscape_drvdata }, { }, };@@ -121,6 +202,8 @@ static int ls_pcie_probe(struct platform_device *pdev)if (!pci)return -ENOMEM ; + pcie->drvdata =of_device_get_match_data (dev); + pci->dev = dev; pci->pp.ops = &ls_pcie_host_ops;@@ -131,6 +214,10 @@ static int ls_pcie_probe(struct platform_device *pdev)if (IS_ERR (pci->dbi_base))return PTR_ERR (pci->dbi_base); + pcie->big_endian =of_property_read_bool (dev->of_node,"big-endian" ); + + pcie->pf_base = pci->dbi_base + pcie->drvdata->pf_off; +if (!ls_pcie_is_bridge (pcie))return -ENODEV ;@@ -139,12 +226,37 @@ static int ls_pcie_probe(struct platform_device *pdev)return dw_pcie_host_init (&pci->pp); } +static int ls_pcie_suspend_noirq (struct device *dev) +{ +struct ls_pcie *pcie =dev_get_drvdata (dev); + +if (!pcie->drvdata->pm_support) +return 0 ; + +return dw_pcie_suspend_noirq (pcie->pci); +} + +static int ls_pcie_resume_noirq (struct device *dev) +{ +struct ls_pcie *pcie =dev_get_drvdata (dev); + +if (!pcie->drvdata->pm_support) +return 0 ; + +return dw_pcie_resume_noirq (pcie->pci); +} + +static const struct dev_pm_ops ls_pcie_pm_ops = { +NOIRQ_SYSTEM_SLEEP_PM_OPS (ls_pcie_suspend_noirq, ls_pcie_resume_noirq) +}; +static struct platform_driver ls_pcie_driver = { .probe = ls_pcie_probe, .driver = { .name ="layerscape-pcie" , .of_match_table = ls_pcie_of_match, .suppress_bind_attrs = true, + .pm = &ls_pcie_pm_ops, }, };builtin_platform_driver (ls_pcie_driver);Signature · 1 line
2.34.1
Signature · 1 line
மணிவண்ணன் சதாசிவம்
Frank Li
maintainerRe: [PATCH v10 resent 3/3] PCI: layerscape: Add power management support for ls1028a
Quoted 117 lines · Manivannan Sadhasivam
Quoted 116 lines · Frank Li
From: Hou Zhiqiang <[email protected]>
Add PME_Turn_off/PME_TO_Ack handshake sequence for ls1028a platform. Call common dwc dw_pcie_suspend(resume)_noirq() function when system enter/exit suspend state.
Signed-off-by Hou Zhiqiang <[email protected]>Signed-off-by Frank Li <[email protected]>--- drivers/pci/controller/dwc/pci-layerscape.c | 130 ++++++++++++++++++-- 1 file changed, 121 insertions(+), 9 deletions(-)drivers/pci/controller/dwc/pci-layerscape.c +65
-0@@ -8,9 +8,11 @@* Author: Minghuan Lian <[email protected]> */ +#include <linux/delay.h> #include <linux/kernel.h> #include <linux/interrupt.h> #include <linux/init.h> +#include <linux/iopoll.h> #include <linux/of_pci.h> #include <linux/of_platform.h> #include <linux/of_address.h> @@ -20,6 +22,7 @@#include <linux/mfd/syscon.h> #include <linux/regmap.h> +#include "../../pci.h" #include "pcie-designware.h" /* PEX Internal Configuration Registers */ @@ -27,12 +30,26 @@#define PCIE_ABSERR 0x8d0/* Bridge Slave Error Response Register */ #define PCIE_ABSERR_SETTING 0x9401/* Forward error of non-posted request */ +/* PF Message Command Register */ +#define LS_PCIE_PF_MCR 0x2c +#define PF_MCR_PTOMR BIT(0) +#define PF_MCR_EXL2S BIT(1) +#define PCIE_IATU_NUM 6 +struct ls_pcie_drvdata { +const u32 pf_off; +bool pm_support; +}; +struct ls_pcie {struct dw_pcie *pci; +const struct ls_pcie_drvdata *drvdata; +void __iomem *pf_base; +bool big_endian; }; +#define ls_pcie_pf_readl_addr (addr) ls_pcie_pf_readl(pcie, addr)#define to_ls_pcie (x) dev_get_drvdata((x)->dev)static bool ls_pcie_is_bridge (struct ls_pcie *pcie)@@ -73,6 +90,60 @@ static void ls_pcie_fix_error_response(struct ls_pcie *pcie)iowrite32 (PCIE_ABSERR_SETTING , pci->dbi_base +PCIE_ABSERR ); } +static u32 ls_pcie_pf_readl (struct ls_pcie *pcie,u32 off) +{ +if (pcie->big_endian) +return ioread32be (pcie->pf_base + off); + +return ioread32 (pcie->pf_base + off); +} + +static void ls_pcie_pf_writel (struct ls_pcie *pcie,u32 off,u32 val) +{ +if (pcie->big_endian) +iowrite32be (val, pcie->pf_base + off); +else +iowrite32 (val, pcie->pf_base + off); +} + +static void ls_pcie_send_turnoff_msg (struct dw_pcie_rp *pp) +{ +struct dw_pcie *pci =to_dw_pcie_from_pp (pp); +struct ls_pcie *pcie =to_ls_pcie (pci); +u32 val; +int ret; + + val =ls_pcie_pf_readl (pcie,LS_PCIE_PF_MCR ); + val |=PF_MCR_PTOMR ; +ls_pcie_pf_writel (pcie,LS_PCIE_PF_MCR , val); + + ret =readx_poll_timeout (ls_pcie_pf_readl_addr,LS_PCIE_PF_MCR , + val, !(val &PF_MCR_PTOMR ), +PCIE_PME_TO_L2_TIMEOUT_US /10 , +PCIE_PME_TO_L2_TIMEOUT_US ); +if (ret) +dev_err (pcie->pci->dev,"poll turn off message timeout\n" ); +} + +static void ls_pcie_exit_from_l2 (struct dw_pcie_rp *pp) +{ +struct dw_pcie *pci =to_dw_pcie_from_pp (pp); +struct ls_pcie *pcie =to_ls_pcie (pci); +u32 val; +int ret; + + val =ls_pcie_pf_readl (pcie,LS_PCIE_PF_MCR ); + val |=PF_MCR_EXL2S ; +ls_pcie_pf_writel (pcie,LS_PCIE_PF_MCR , val); + + ret = readx_poll_timeout(ls_pcie_pf_readl_addr, LS_PCIE_PF_MCR, + val, !(val & PF_MCR_EXL2S),
Quoted 8 lines
drivers/pci/controller/dwc/pci-layerscape.c static void ls_pcie_fix_error_response(struct ls_pcie *pcie) · line 144
Quoted 4 lines
drivers/pci/controller/dwc/pci-layerscape.c +4
-0+PCIE_PME_TO_L2_TIMEOUT_US /10 , + PCIE_PME_TO_L2_TIMEOUT_US); +if (ret) +dev_err (pcie->pci->dev,"poll exit L2 state timeout\n" );I specifically mentioned that you need to change this error message and the one below before adding my Acked-by tag. But you just added the tag without incorporating the changes :/
Sorry, I found I forget run 'git add' when I run git commit --amend. Change just leave in local tree.
Will Send v11.
Frank
Quoted 110 lines
- Mani
Quoted 104 lines
drivers/pci/controller/dwc/pci-layerscape.c +52
-9+} +static int ls_pcie_host_init (struct dw_pcie_rp *pp) {struct dw_pcie *pci =to_dw_pcie_from_pp (pp);@@ -91,18 +162,28 @@ static int ls_pcie_host_init(struct dw_pcie_rp *pp)static const struct dw_pcie_host_ops ls_pcie_host_ops = { .host_init = ls_pcie_host_init, + .pme_turn_off = ls_pcie_send_turnoff_msg, + .exit_from_l2 = ls_pcie_exit_from_l2, +}; + +static const struct ls_pcie_drvdata ls1021a_drvdata = { +}; + +static const struct ls_pcie_drvdata layerscape_drvdata = { + .pf_off =0xc0000 , + .pm_support = true, };static const struct of_device_id ls_pcie_of_match[] = { - { .compatible ="fsl,ls1012a-pcie" , }, - { .compatible ="fsl,ls1021a-pcie" , }, - { .compatible ="fsl,ls1028a-pcie" , }, - { .compatible ="fsl,ls1043a-pcie" , }, - { .compatible ="fsl,ls1046a-pcie" , }, - { .compatible ="fsl,ls2080a-pcie" , }, - { .compatible ="fsl,ls2085a-pcie" , }, - { .compatible ="fsl,ls2088a-pcie" , }, - { .compatible ="fsl,ls1088a-pcie" , }, + { .compatible ="fsl,ls1012a-pcie" , .data = &layerscape_drvdata }, + { .compatible ="fsl,ls1021a-pcie" , .data = &ls1021a_drvdata }, + { .compatible ="fsl,ls1028a-pcie" , .data = &layerscape_drvdata }, + { .compatible ="fsl,ls1043a-pcie" , .data = &ls1021a_drvdata }, + { .compatible ="fsl,ls1046a-pcie" , .data = &layerscape_drvdata }, + { .compatible ="fsl,ls2080a-pcie" , .data = &layerscape_drvdata }, + { .compatible ="fsl,ls2085a-pcie" , .data = &layerscape_drvdata }, + { .compatible ="fsl,ls2088a-pcie" , .data = &layerscape_drvdata }, + { .compatible ="fsl,ls1088a-pcie" , .data = &layerscape_drvdata }, { }, };@@ -121,6 +202,8 @@ static int ls_pcie_probe(struct platform_device *pdev)if (!pci)return -ENOMEM ; + pcie->drvdata =of_device_get_match_data (dev); + pci->dev = dev; pci->pp.ops = &ls_pcie_host_ops;@@ -131,6 +214,10 @@ static int ls_pcie_probe(struct platform_device *pdev)if (IS_ERR (pci->dbi_base))return PTR_ERR (pci->dbi_base); + pcie->big_endian =of_property_read_bool (dev->of_node,"big-endian" ); + + pcie->pf_base = pci->dbi_base + pcie->drvdata->pf_off; +if (!ls_pcie_is_bridge (pcie))return -ENODEV ;@@ -139,12 +226,37 @@ static int ls_pcie_probe(struct platform_device *pdev)return dw_pcie_host_init (&pci->pp); } +static int ls_pcie_suspend_noirq (struct device *dev) +{ +struct ls_pcie *pcie =dev_get_drvdata (dev); + +if (!pcie->drvdata->pm_support) +return 0 ; + +return dw_pcie_suspend_noirq (pcie->pci); +} + +static int ls_pcie_resume_noirq (struct device *dev) +{ +struct ls_pcie *pcie =dev_get_drvdata (dev); + +if (!pcie->drvdata->pm_support) +return 0 ; + +return dw_pcie_resume_noirq (pcie->pci); +} + +static const struct dev_pm_ops ls_pcie_pm_ops = { +NOIRQ_SYSTEM_SLEEP_PM_OPS (ls_pcie_suspend_noirq, ls_pcie_resume_noirq) +}; +static struct platform_driver ls_pcie_driver = { .probe = ls_pcie_probe, .driver = { .name ="layerscape-pcie" , .of_match_table = ls_pcie_of_match, .suppress_bind_attrs = true, + .pm = &ls_pcie_pm_ops, }, };builtin_platform_driver (ls_pcie_driver);Signature · 1 line
2.34.1Signature · 1 line
மணிவண்ணன் சதாசிவம்