Add support for Allwinner PWM on D1/T113s/R329 SoCs
Subsystems (4)
v6 cover Add support for Allwinner PWM on D1/T113s/R329 SoCs
Hi,
This series adds support for PWM controller on new Allwinner's SoCs, such as D1, T113s and R329. The implemented driver provides basic functionality for control PWM channels.
v2:
- fix dt-bindings
- fix a remark in the driver
v3:
- fix dt-bindings
- fix sunxi-d1s-t113.dtsi
v4:
- fix a remark in the driver
v5:
- dropped unused varibale in the driver
- fix dt-bindings
v6:
- add apb0 clock
Aleksandr Shubin (3):
dt-bindings: pwm: Add binding for Allwinner D1/T113-S3/R329 PWM
controller
pwm: Add Allwinner's D1/T113-S3/R329 SoCs PWM support
riscv: dts: allwinner: d1: Add pwm node
.../bindings/pwm/allwinner,sun20i-pwm.yaml | 87 +++++ .../boot/dts/allwinner/sunxi-d1s-t113.dtsi | 12 + drivers/pwm/Kconfig | 10 + drivers/pwm/Makefile | 1 + drivers/pwm/pwm-sun20i.c | 328 ++++++++++++++++++ 5 files changed, 438 insertions(+) create mode 100644 Documentation/devicetree/bindings/pwm/allwinner,sun20i-pwm.yaml create mode 100644 drivers/pwm/pwm-sun20i.c
Signature · 1 line
2.25.1
PATCH v6 1/3 dt-bindings: pwm: Add binding for Allwinner D1/T113-S3/R329 PWM controller
Allwinner's D1, T113-S3 and R329 SoCs have a new pwm controller witch is different from the previous pwm-sun4i.
The D1 and T113 are identical in terms of peripherals, they differ only in the architecture of the CPU core, and even share the majority of their DT. Because of that, using the same compatible makes sense.
The R329 is a different SoC though, and should have a different compatible string added, especially as there is a difference in the number of channels.
D1 and T113s SoCs have one PWM controller with 8 channels. R329 SoC has two PWM controllers in both power domains, one of them has 9 channels (CPUX one) and the other has 6 (CPUS one).
Add a device tree binding for them.
--- .../bindings/pwm/allwinner,sun20i-pwm.yaml | 87 +++++++++++++++++++ 1 file changed, 87 insertions(+) create mode 100644 Documentation/devicetree/bindings/pwm/allwinner,sun20i-pwm.yaml
Documentation/devicetree/bindings/pwm/allwinner,sun20i-pwm.yaml new file +87 -0
@@ -0,0 +1,87 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pwm/allwinner,sun20i-pwm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner D1, T113-S3 and R329 PWM + +maintainers: + - Aleksandr Shubin <[email protected]> + +properties: + compatible: + oneOf: + - const: allwinner,sun20i-d1-pwm + - items: + - const: allwinner,sun20i-r329-pwm + - const: allwinner,sun20i-d1-pwm + + reg: + maxItems: 1 + + "#pwm-cells": + const: 3 + + clocks: + items: + - description: Bus clock + - description: 24 MHz oscillator + - description: APB0 clock + + clock-names: + items: + - const: bus + - const: hosc + - const: apb0 + + resets: + maxItems: 1 + + allwinner,pwm-channels: + $ref: /schemas/types.yaml#/definitions/uint32 + description: The number of PWM channels configured for this instance + enum: [6, 9] + +allOf: + - $ref: pwm.yaml# + + - if: + properties: + compatible: + contains: + const: allwinner,sun20i-r329-pwm + + then: + required: + - allwinner,pwm-channels + + else: + properties: + allwinner,pwm-channels: false + +unevaluatedProperties: false + +required: + - compatible + - reg + - "#pwm-cells" + - clocks + - clock-names + - resets + +examples: + - | + #include <dt-bindings/clock/sun20i-d1-ccu.h> + #include <dt-bindings/reset/sun20i-d1-ccu.h> + + pwm: pwm@2000c00 { + compatible = "allwinner,sun20i-d1-pwm"; + reg = <0x02000c00 0x400>; + clocks = <&ccu CLK_BUS_PWM>, <&dcxo>, <&ccu CLK_APB0>; + clock-names = "bus", "hosc", "apb0"; + resets = <&ccu RST_BUS_PWM>; + #pwm-cells = <0x3>; + }; + +...
Signature · 1 line
2.25.1
PATCH v6 2/3 pwm: Add Allwinner's D1/T113-S3/R329 SoCs PWM support
In reply to Aleksandr ShubinAllwinner's D1, T113-S3 and R329 SoCs have a quite different PWM controllers with ones supported by pwm-sun4i driver.
This patch adds a PWM controller driver for Allwinner's D1, T113-S3 and R329 SoCs. The main difference between these SoCs is the number of channels defined by the DT property.
--- drivers/pwm/Kconfig | 10 ++ drivers/pwm/Makefile | 1 + drivers/pwm/pwm-sun20i.c | 328 +++++++++++++++++++++++++++++++++++++++ 3 files changed, 339 insertions(+) create mode 100644 drivers/pwm/pwm-sun20i.c
drivers/pwm/Kconfig +10 -0
@@ -594,6 +594,16 @@ config PWM_SUN4I To compile this driver as a module, choose M here: the module will be called pwm-sun4i. +config PWM_SUN20I + tristate "Allwinner D1/T113s/R329 PWM support" + depends on ARCH_SUNXI || COMPILE_TEST + depends on COMMON_CLK + help + Generic PWM framework driver for Allwinner D1/T113s/R329 SoCs. + + To compile this driver as a module, choose M here: the module + will be called pwm-sun20i. + config PWM_SUNPLUS tristate "Sunplus PWM support" depends on ARCH_SUNPLUS || COMPILE_TEST
drivers/pwm/Makefile +1 -0
@@ -55,6 +55,7 @@ obj-$(CONFIG_PWM_STM32) += pwm-stm32.o obj-$(CONFIG_PWM_STM32_LP) += pwm-stm32-lp.o obj-$(CONFIG_PWM_STMPE) += pwm-stmpe.o obj-$(CONFIG_PWM_SUN4I) += pwm-sun4i.o +obj-$(CONFIG_PWM_SUN20I) += pwm-sun20i.o obj-$(CONFIG_PWM_SUNPLUS) += pwm-sunplus.o obj-$(CONFIG_PWM_TEGRA) += pwm-tegra.o obj-$(CONFIG_PWM_TIECAP) += pwm-tiecap.o
drivers/pwm/pwm-sun20i.c new file +328 -0
328 lines not on this page · raw message
Signature · 1 line
2.25.1
Re: [PATCH v6 2/3] pwm: Add Allwinner's D1/T113-S3/R329 SoCs PWM support
Hello Aleksandr,
Quoted 71 lines · Aleksandr Shubin
Allwinner's D1, T113-S3 and R329 SoCs have a quite different PWM controllers with ones supported by pwm-sun4i driver.
This patch adds a PWM controller driver for Allwinner's D1, T113-S3 and R329 SoCs. The main difference between these SoCs is the number of channels defined by the DT property.
Signed-off-by Aleksandr Shubin <[email protected]>--- drivers/pwm/Kconfig | 10 ++ drivers/pwm/Makefile | 1 + drivers/pwm/pwm-sun20i.c | 328 +++++++++++++++++++++++++++++++++++++++ 3 files changed, 339 insertions(+) create mode 100644 drivers/pwm/pwm-sun20i.cdrivers/pwm/Kconfig +10
-0@@ -594,6 +594,16 @@ config PWM_SUN4I To compile this driver as a module, choose M here: the module will be called pwm-sun4i. +config PWM_SUN20I + tristate "Allwinner D1/T113s/R329 PWM support" + depends on ARCH_SUNXI || COMPILE_TEST + depends on COMMON_CLK + help + Generic PWM framework driver for Allwinner D1/T113s/R329 SoCs. + + To compile this driver as a module, choose M here: the module + will be called pwm-sun20i. + config PWM_SUNPLUS tristate "Sunplus PWM support" depends on ARCH_SUNPLUS || COMPILE_TESTdrivers/pwm/Makefile +1
-0@@ -55,6 +55,7 @@ obj-$(CONFIG_PWM_STM32) += pwm-stm32.o obj-$(CONFIG_PWM_STM32_LP) += pwm-stm32-lp.o obj-$(CONFIG_PWM_STMPE) += pwm-stmpe.o obj-$(CONFIG_PWM_SUN4I) += pwm-sun4i.o +obj-$(CONFIG_PWM_SUN20I) += pwm-sun20i.o obj-$(CONFIG_PWM_SUNPLUS) += pwm-sunplus.o obj-$(CONFIG_PWM_TEGRA) += pwm-tegra.o obj-$(CONFIG_PWM_TIECAP) += pwm-tiecap.odrivers/pwm/pwm-sun20i.c new file +17
-0@@ -0,0 +1,328 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* PWM Controller Driver for sunxi platforms (D1, T113-S3 and R329) +* +* Limitations: +* - When the parameters change, current running period will not be completed +* and run new settings immediately. +* - It output HIGH-Z state when PWM channel disabled. +* +* Copyright (c) 2023 Aleksandr Shubin <[email protected]> +*/ + +#include <linux/bitfield.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/module.h>
drivers/pwm/pwm-sun20i.c line 27
Quoted 10 lines
drivers/pwm/pwm-sun20i.c new file +10
-0+#include <linux/of_device.h> +#include <linux/pwm.h> +#include <linux/reset.h> + +#define PWM_CLK_CFG (chan) (0x20 + (((chan) >> 1) * 0x4)) +#define PWM_CLK_CFG_SRC GENMASK(8, 7) +#define PWM_CLK_CFG_DIV_M GENMASK(3, 0) + +#define PWM_CLK_GATE 0x40 +#define PWM_CLK_GATE_BYPASS (chan) BIT((chan) - 16)
Really? With chan == 0 this gives you BIT(-16).
Quoted 4 lines
drivers/pwm/pwm-sun20i.c new file +4
-0+#define PWM_CLK_GATE_GATING (chan) BIT(chan) + +#define PWM_ENABLE 0x80 +#define PWM_ENABLE_EN (chan) BIT(chan)
drivers/pwm/pwm-sun20i.c line 41
Quoted 10 lines
drivers/pwm/pwm-sun20i.c new file +10
-0+ +#define PWM_CTL (chan) (0x100 + (chan) * 0x20) +#define PWM_CTL_ACT_STA BIT(8) +#define PWM_CTL_PRESCAL_K GENMASK(7, 0) + +#define PWM_PERIOD (chan) (0x104 + (chan) * 0x20) +#define PWM_PERIOD_ENTIRE_CYCLE GENMASK(31, 16) +#define PWM_PERIOD_ACT_CYCLE GENMASK(15, 0) + +#define PWM_MAGIC (255 * 65535 + 2 * 65534 + 1)
A comment about PWM_MAGIC would be nice.
I'd like to have these register defines prefixed with (say) SUN20I_, otherwise the names are too generic and likely overlap with other defines.
Quoted 44 lines
drivers/pwm/pwm-sun20i.c new file +44
-0+struct sun20i_pwm_chip { +struct clk *clk_bus, *clk_hosc, *clk_apb0; +struct reset_control *rst; +struct pwm_chip chip; +void __iomem *base; +/* Mutex to protect pwm apply state */ +struct mutex mutex; +}; + +static inline struct sun20i_pwm_chip *to_sun20i_pwm_chip (struct pwm_chip *chip) +{ + return container_of(chip, struct sun20i_pwm_chip, chip); +} + +static inline u32 sun20i_pwm_readl (struct sun20i_pwm_chip *chip, +unsigned long offset) +{ +return readl (chip->base + offset); +} + +static inline void sun20i_pwm_writel (struct sun20i_pwm_chip *chip, +u32 val,unsigned long offset) +{ +writel (val, chip->base + offset); +} + +static int sun20i_pwm_get_state (struct pwm_chip *chip, +struct pwm_device *pwm, +struct pwm_state *state) +{ +struct sun20i_pwm_chip *sun20i_chip =to_sun20i_pwm_chip (chip); +u16 ent_cycle, act_cycle, prescal; +u64 clk_rate, tmp; +u8 div_id; +u32 val; + +mutex_lock (&sun20i_chip->mutex); + + val =sun20i_pwm_readl (sun20i_chip,PWM_CLK_CFG (pwm->hwpwm)); + div_id =FIELD_GET (PWM_CLK_CFG_DIV_M , val); +if (FIELD_GET (PWM_CLK_CFG_SRC , val) ==0 ) + clk_rate =clk_get_rate (sun20i_chip->clk_hosc); +else + clk_rate =clk_get_rate (sun20i_chip->clk_apb0);
drivers/pwm/pwm-sun20i.c line 96
Quoted 10 lines
drivers/pwm/pwm-sun20i.c new file +10
-0+ + val =sun20i_pwm_readl (sun20i_chip,PWM_CTL (pwm->hwpwm)); + state->polarity = (PWM_CTL_ACT_STA & val) ?PWM_POLARITY_NORMAL :PWM_POLARITY_INVERSED ; + + prescal =FIELD_GET (PWM_CTL_PRESCAL_K , val) +1 ; + + val =sun20i_pwm_readl (sun20i_chip,PWM_ENABLE ); + state->enabled = (PWM_ENABLE_EN (pwm->hwpwm) & val) ? true : false; + + val =sun20i_pwm_readl (sun20i_chip,PWM_PERIOD (pwm->hwpwm));
You can release the lock already here (or even after PWM_ENABLE is read?)
drivers/pwm/pwm-sun20i.c line 107
Quoted 11 lines
drivers/pwm/pwm-sun20i.c new file +11
-0+ act_cycle =FIELD_GET (PWM_PERIOD_ACT_CYCLE , val); + ent_cycle =FIELD_GET (PWM_PERIOD_ENTIRE_CYCLE , val); + +/* +* The duration of the active phase should not be longer +* than the duration of the period +*/ +if (act_cycle > ent_cycle) + act_cycle = ent_cycle; + + tmp = ((u64)(act_cycle) * prescal << div_id) *NSEC_PER_SEC ;
act_cycle is a 16 bit value, prescal is <= 256 and div_id is <= 15. So the maximal value tmp has to hold is 0x1dcd47329b00000000. This doesn't fit into an u64. You need something like mul_u64_u64_div64_roundup here.
Quoted 20 lines
drivers/pwm/pwm-sun20i.c new file +20
-0+ state->duty_cycle =DIV_ROUND_UP_ULL (tmp, clk_rate); + tmp = ((u64)(ent_cycle) * prescal << div_id) *NSEC_PER_SEC ; + state->period =DIV_ROUND_UP_ULL (tmp, clk_rate); +mutex_unlock (&sun20i_chip->mutex); + +return 0 ; +} + +static int sun20i_pwm_apply (struct pwm_chip *chip,struct pwm_device *pwm, +const struct pwm_state *state) +{ +struct sun20i_pwm_chip *sun20i_chip =to_sun20i_pwm_chip (chip); +u32 clk_gate, clk_cfg, pwm_en, ctl, period; +u64 bus_rate, hosc_rate, clk_div, val; +u32 prescaler, div_m; +bool use_bus_clk; +int ret =0 ; + +mutex_lock (&sun20i_chip->mutex); +
drivers/pwm/pwm-sun20i.c line 137
Quoted 10 lines
drivers/pwm/pwm-sun20i.c new file +10
-0+ pwm_en =sun20i_pwm_readl (sun20i_chip,PWM_ENABLE ); + +if (state->enabled != pwm->state.enabled) + clk_gate =sun20i_pwm_readl (sun20i_chip,PWM_CLK_GATE ); + +if (state->enabled != pwm->state.enabled && !state->enabled) { + clk_gate &= ~PWM_CLK_GATE_GATING (pwm->hwpwm); + pwm_en &= ~PWM_ENABLE_EN (pwm->hwpwm); +sun20i_pwm_writel (sun20i_chip, pwm_en,PWM_ENABLE ); +sun20i_pwm_writel (sun20i_chip, clk_gate,PWM_CLK_GATE );
Does ENABLE configure if the output pin is driven?
drivers/pwm/pwm-sun20i.c line 137
Quoted 1 line
drivers/pwm/pwm-sun20i.c new file +1
-0+ }
You can these to like:
if (state->enabled != pwm->state.enabled) {
clk_gate = ...
if (!state->enabled) {
...
}
}drivers/pwm/pwm-sun20i.c line 150
Quoted 12 lines
drivers/pwm/pwm-sun20i.c new file +12
-0+ +if (state->polarity != pwm->state.polarity || + state->duty_cycle != pwm->state.duty_cycle || + state->period != pwm->state.period) { + ctl =sun20i_pwm_readl (sun20i_chip,PWM_CTL (pwm->hwpwm)); + clk_cfg =sun20i_pwm_readl (sun20i_chip,PWM_CLK_CFG (pwm->hwpwm)); + hosc_rate =clk_get_rate (sun20i_chip->clk_hosc); + bus_rate =clk_get_rate (sun20i_chip->clk_apb0); +if (pwm_en &PWM_ENABLE_EN (pwm->hwpwm ^1 )) { +/* if the neighbor channel is enable, check period only */ + use_bus_clk =FIELD_GET (PWM_CLK_CFG_SRC , clk_cfg) !=0 ; + val = state->period * (use_bus_clk ? bus_rate : hosc_rate);
This can overflow.
Quoted 9 lines
drivers/pwm/pwm-sun20i.c new file +9
-0+do_div (val,NSEC_PER_SEC ); + + div_m =FIELD_GET (PWM_CLK_CFG_DIV_M , clk_cfg); + }else { +/* check period and select clock source */ + use_bus_clk = false; + val = state->period * hosc_rate; +do_div (val,NSEC_PER_SEC ); +if (val <=1 ) {
drivers/pwm/pwm-sun20i.c line 169
Quoted 10 lines
drivers/pwm/pwm-sun20i.c new file +10
-0+ use_bus_clk = true; + val = state->period * bus_rate; +do_div (val,NSEC_PER_SEC ); +if (val <=1 ) { + ret = -EINVAL ; + goto unlock_mutex; + } + } + div_m =fls (DIV_ROUND_DOWN_ULL (val,PWM_MAGIC )); +if (div_m >=9 ) {
What is 9 here? Something like DIV_M_MAX? There are a few other constants that might deserve a name.
Quoted 7 lines
drivers/pwm/pwm-sun20i.c new file +7
-0+ ret = -EINVAL ; + goto unlock_mutex; + } + +/* set up the CLK_DIV_M and clock CLK_SRC */ + clk_cfg =FIELD_PREP (PWM_CLK_CFG_DIV_M , div_m); + clk_cfg |=FIELD_PREP (PWM_CLK_CFG_SRC , use_bus_clk);
drivers/pwm/pwm-sun20i.c line 186
Quoted 10 lines
drivers/pwm/pwm-sun20i.c new file +10
-0+ +sun20i_pwm_writel (sun20i_chip, clk_cfg,PWM_CLK_CFG (pwm->hwpwm)); + } + +/* calculate prescaler, PWM entire cycle */ + clk_div = val >> div_m; +if (clk_div <=65534 ) { + prescaler =0 ; + }else { + prescaler =DIV_ROUND_UP_ULL (clk_div -65534 ,65535 );
This looks strange. The result is the same as DIV_ROUND_DOWN_ULL(clk_div, 65535) which by the way also does the right thing for clk_div <= 65534.
drivers/pwm/pwm-sun20i.c line 189
Quoted 3 lines
drivers/pwm/pwm-sun20i.c new file +3
-0+if (prescaler >=256 ) { + ret = -EINVAL ; + goto unlock_mutex;
If this happens the requested period is too big, right? Please use
prescaler = 255;
then and proceed. (The idea is to configure the biggest period that is not bigger than the requested period.)
Quoted 12 lines
drivers/pwm/pwm-sun20i.c new file +12
-0+ } +do_div (clk_div, prescaler +1 ); + } + + period =FIELD_PREP (PWM_PERIOD_ENTIRE_CYCLE , clk_div); + +/* set duty cycle */ + val = state->duty_cycle * (use_bus_clk ? bus_rate : hosc_rate); +do_div (val,NSEC_PER_SEC ); + clk_div = val >> div_m; +do_div (clk_div, prescaler +1 ); +
drivers/pwm/pwm-sun20i.c line 211
Quoted 10 lines
drivers/pwm/pwm-sun20i.c new file +10
-0+/* +* The formula of the output period and the duty-cycle for PWM are as follows. +* T period = (PWM01_CLK / PWM0_PRESCALE_K)^-1 * (PPR0.PWM_ENTIRE_CYCLE + 1) +* T high-level = (PWM01_CLK / PWM0_PRESCALE_K)^-1 * PPR0.PWM_ACT_CYCLE +* Duty-cycle = T high-level / T period +* In accordance with this formula, in order to set the duty-cycle to 100%, +* it is necessary that PWM_ACT_CYCLE >= PWM_ENTIRE_CYCLE + 1 +*/ +if (state->duty_cycle == state->period) + clk_div++;
Can it happen, that clk_div gets too big here?
drivers/pwm/pwm-sun20i.c line 212
Quoted 1 line
drivers/pwm/pwm-sun20i.c new file +1
-0+ period |=FIELD_PREP (PWM_PERIOD_ACT_CYCLE , clk_div);
It's a bit irritating (to me at least) that the variable "period" holds the configuration for the duty_cycle. Maybe call it "reg_period" or similar to not confuse it with state->period?
drivers/pwm/pwm-sun20i.c line 219
Quoted 7 lines
drivers/pwm/pwm-sun20i.c new file +7
-0+sun20i_pwm_writel (sun20i_chip, period,PWM_PERIOD (pwm->hwpwm)); + + ctl =FIELD_PREP (PWM_CTL_PRESCAL_K , prescaler); +if (state->polarity ==PWM_POLARITY_NORMAL ) + ctl |=PWM_CTL_ACT_STA ; + +sun20i_pwm_writel (sun20i_chip, ctl,PWM_CTL (pwm->hwpwm));
Is there a glitch if you switch polarity? i.e. after period is written a few lines above, a new period starts already and if you then invert PWM_CTL_ACT_STA, the output immediately switches polarity? If so that's something to mention in the Limitations section.
Quoted 29 lines
drivers/pwm/pwm-sun20i.c new file +29
-0+ } +[...] +static int sun20i_pwm_probe (struct platform_device *pdev) +{ +struct sun20i_pwm_chip *sun20i_chip; +int ret; + + sun20i_chip =devm_kzalloc (&pdev->dev,sizeof (*sun20i_chip),GFP_KERNEL ); +if (!sun20i_chip) +return -ENOMEM ; + + sun20i_chip->base =devm_platform_ioremap_resource (pdev,0 ); +if (IS_ERR (sun20i_chip->base)) +return PTR_ERR (sun20i_chip->base); + + sun20i_chip->clk_bus =devm_clk_get_enabled (&pdev->dev,"bus" ); +if (IS_ERR (sun20i_chip->clk_bus)) +return dev_err_probe (&pdev->dev,PTR_ERR (sun20i_chip->clk_bus), +"failed to get bus clock\n" ); + + sun20i_chip->clk_hosc =devm_clk_get_enabled (&pdev->dev,"hosc" ); +if (IS_ERR (sun20i_chip->clk_hosc)) +return dev_err_probe (&pdev->dev,PTR_ERR (sun20i_chip->clk_hosc), +"failed to get hosc clock\n" ); + + sun20i_chip->clk_apb0 =devm_clk_get_enabled (&pdev->dev,"apb0" ); +if (IS_ERR (sun20i_chip->clk_apb0)) +return dev_err_probe (&pdev->dev,PTR_ERR (sun20i_chip->clk_apb0), +"failed to get apb0 clock\n" );
drivers/pwm/pwm-sun20i.c line 284
Quoted 10 lines
drivers/pwm/pwm-sun20i.c new file +10
-0+ + sun20i_chip->rst =devm_reset_control_get_exclusive (&pdev->dev,NULL ); +if (IS_ERR (sun20i_chip->rst)) +return dev_err_probe (&pdev->dev,PTR_ERR (sun20i_chip->rst), +"failed to get bus reset\n" ); + + ret =of_property_read_u32 (pdev->dev.of_node,"allwinner,pwm-channels" , + &sun20i_chip->chip.npwm); +if (ret) + sun20i_chip->chip.npwm =8 ;
The register layout allows npwm <= 16 only, right? I suggest to add a check for that.
drivers/pwm/pwm-sun20i.c line 289
Quoted 4 lines
drivers/pwm/pwm-sun20i.c new file +4
-0+/* Deassert reset */ + ret =reset_control_deassert (sun20i_chip->rst); +if (ret) +return dev_err_probe (&pdev->dev, ret,"failed to deassert reset\n" );
Best regards
Uwe
Signature · 2 lines
Pengutronix e.K. | Uwe Kleine-König | Industrial Linux Solutions | https://www.pengutronix.de/ |
PATCH v6 3/3 riscv: dts: allwinner: d1: Add pwm node
In reply to Aleksandr ShubinD1 and T113s contain a pwm controller with 8 channels. This controller is supported by the sun20i-pwm driver.
Add a device tree node for it.
--- arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+)
arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi +12 -0
@@ -127,6 +127,18 @@ uart3_pb_pins: uart3-pb-pins { }; }; + pwm: pwm@2000c00 { + compatible = "allwinner,sun20i-d1-pwm"; + reg = <0x02000c00 0x400>; + clocks = <&ccu CLK_BUS_PWM>, + <&dcxo>, + <&ccu CLK_APB0>; + clock-names = "bus", "hosc", "apb0"; + resets = <&ccu RST_BUS_PWM>; + status = "disabled"; + #pwm-cells = <0x3>; + }; + ccu: clock-controller@2001000 { compatible = "allwinner,sun20i-d1-ccu"; reg = <0x2001000 0x1000>;
Signature · 1 line
2.25.1
Quoted 5 lines · Aleksandr Shubin
Hi,
This series adds support for PWM controller on new Allwinner's SoCs, such as D1, T113s and R329. The implemented driver provides basic functionality for control PWM channels.
I have tested this patch and earlier versions successfully on a Mango Pi MQ Dual and verified it outputs a PWM signal.
John.
Hi John,
Quoted 7 lines · John Watts
Quoted 3 lines · Aleksandr Shubin
This series adds support for PWM controller on new Allwinner's SoCs, such as D1, T113s and R329. The implemented driver provides basic functionality for control PWM channels.
I have tested this patch and earlier versions successfully on a Mango Pi MQ Dual and verified it outputs a PWM signal.
If you want that documented, the usual thing to do is to include a
Tested-by: tag in your reply.
Best regards
Uwe
Signature · 2 lines
Pengutronix e.K. | Uwe Kleine-König | Industrial Linux Solutions | https://www.pengutronix.de/ |
Quoted 8 lines · Uwe Kleine-König
Hi John,
Quoted 5 lines · John Watts
Quoted 3 lines · Aleksandr Shubin
This series adds support for PWM controller on new Allwinner's SoCs, such as D1, T113s and R329. The implemented driver provides basic functionality for control PWM channels.
Quoted 5 lines
Quoted 2 lines
I have tested this patch and earlier versions successfully on a Mango Pi MQ Dual and verified it outputs a PWM signal.
If you want that documented, the usual thing to do is to include a
Tested-by: tag in your reply.
That's a good idea! I'll take a closer look under a scope and against the data sheet and give another tested-by then when I can. I'm not sure how close that gets to a reviewed-by but I don't have the experience in driver development to know if something is off in the design.
Quoted 3 lines
Best regards
Uwe
John.
Hey John,
Quoted 12 lines · John Watts
Quoted 11 lines · Uwe Kleine-König
Hi John,
Quoted 7 lines · John Watts
Quoted 3 lines · Aleksandr Shubin
This series adds support for PWM controller on new Allwinner's SoCs, such as D1, T113s and R329. The implemented driver provides basic functionality for control PWM channels.
I have tested this patch and earlier versions successfully on a Mango Pi MQ Dual and verified it outputs a PWM signal.
Quoted 7 lines
Quoted 2 lines
If you want that documented, the usual thing to do is to include a
Tested-by: tag in your reply.That's a good idea! I'll take a closer look under a scope and against the data sheet and give another tested-by then when I can. I'm not sure how close that gets to a reviewed-by but I don't have the experience in driver development to know if something is off in the design.
Tested-by has little to nothing to do with development or review. If you tested that patch and it worked for you, that's enough to give such a tag.
Best regards
Uwe
Signature · 2 lines
Pengutronix e.K. | Uwe Kleine-König | Industrial Linux Solutions | https://www.pengutronix.de/ |
Quoted 5 lines · Aleksandr Shubin
Hi,
This series adds support for PWM controller on new Allwinner's SoCs, such as D1, T113s and R329. The implemented driver provides basic functionality for control PWM channels.
I did some more testing of this and it seems to work on my T113, outputting correct periods and duty cycles.
John.