Skip to contentSkip to conversation

board: toradex: verdin-imx8mp: enable usb device and fastboot support

PATCH In review Marcel Ziswiler 4 participants 4 messages Aug 28, 2023 – Oct 28, 2023 Arm i.MX and Layerscape

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 board: toradex: verdin-imx8mp: enable usb device and fastboot support

From: Marcel Ziswiler <[email protected]>

Enable USB device and fastboot support which may be used to load the Toradex Easy Installer FIT image.

While at it also enable USB mass storage aka UMS support.

Note that the i.MX 8M Plus recovery mode support is based on the USB boot stage of the BOOTROM and does NOT require USB SDP SPL aka serial downloader support.

---

 configs/verdin-imx8mp_defconfig | 16 +++++++++++++++-
 1 file changed, 15 insertions(+), 1 deletion(-)
configs/verdin-imx8mp_defconfig +15 -1
index 2df0f4f3443..4c6650c3453 100644
@@ -79,6 +79,7 @@ CONFIG_CMD_I2C=y
 CONFIG_CMD_MMC=y
 CONFIG_CMD_READ=y
 CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
 CONFIG_CMD_BOOTCOUNT=y
 CONFIG_CMD_CACHE=y
 CONFIG_CMD_TIME=y
@@ -108,6 +109,12 @@ CONFIG_BOOTCOUNT_ENV=y
 CONFIG_CLK_COMPOSITE_CCF=y
 CONFIG_CLK_IMX8MP=y
 CONFIG_FSL_CAAM=y
+CONFIG_USB_FUNCTION_FASTBOOT=y
+CONFIG_FASTBOOT_BUF_ADDR=0x42800000
+CONFIG_FASTBOOT_BUF_SIZE=0x40000000
+CONFIG_FASTBOOT_FLASH=y
+CONFIG_FASTBOOT_UUU_SUPPORT=y
+CONFIG_FASTBOOT_FLASH_MMC_DEV=0
 CONFIG_GPIO_HOG=y
 CONFIG_SPL_GPIO_HOG=y
 CONFIG_MXC_GPIO=y
@@ -138,6 +145,7 @@ CONFIG_DWC_ETH_QOS_IMX=y
 CONFIG_FEC_MXC=y
 CONFIG_RGMII=y
 CONFIG_MII=y
+CONFIG_PHY=y
 CONFIG_PHY_IMX8MQ_USB=y
 CONFIG_PINCTRL=y
 CONFIG_SPL_PINCTRL=y
@@ -160,14 +168,20 @@ CONFIG_SYSRESET_WATCHDOG=y
 CONFIG_DM_THERMAL=y
 CONFIG_IMX_TMU=y
 CONFIG_USB=y
+# CONFIG_SPL_DM_USB is not set
+CONFIG_DM_USB_GADGET=y
 CONFIG_USB_XHCI_HCD=y
 CONFIG_USB_XHCI_DWC3=y
 CONFIG_USB_XHCI_DWC3_OF_SIMPLE=y
 CONFIG_USB_EHCI_HCD=y
-CONFIG_MXC_USB_OTG_HACTIVE=y
+# CONFIG_USB_EHCI_MX7 is not set
 CONFIG_USB_DWC3=y
 CONFIG_USB_DWC3_GENERIC=y
 CONFIG_USB_KEYBOARD=y
 CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="Toradex"
+CONFIG_USB_GADGET_VENDOR_NUM=0x1b67
+CONFIG_USB_GADGET_PRODUCT_NUM=0x4000
 CONFIG_IMX_WATCHDOG=y
 CONFIG_HEXDUMP=y
Signature · 1 line
2.36.1
reviewer Reviewed-by on v1 1/1
#1 lore raw

Hi Marcel,

Quoted 6 lines · Marcel Ziswiler

From: Marcel Ziswiler <[email protected]>

Enable USB device and fastboot support which may be used to load the Toradex Easy Installer FIT image.

Quoted 7 lines

While at it also enable USB mass storage aka UMS support.

Note that the i.MX 8M Plus recovery mode support is based on the USB boot stage of the BOOTROM and does NOT require USB SDP SPL aka serial downloader support.

#2 lore raw

Hi Stefano

Maybe you missed that one (i.MX 8M Plus vs. Mini)? Thanks!

Cheers

Marcel

Quoted 18 lines · Fabio Estevam

Hi Marcel,

Quoted 6 lines · Marcel Ziswiler

From: Marcel Ziswiler <[email protected]>

Enable USB device and fastboot support which may be used to load the Toradex Easy Installer FIT image.

Quoted 7 lines

While at it also enable USB mass storage aka UMS support.

Note that the i.MX 8M Plus recovery mode support is based on the USB boot stage of the BOOTROM and does NOT require USB SDP SPL aka serial downloader support.

#3 lore raw
In reply to Marcel Ziswiler
Quoted 5 lines · Marcel Ziswiler

From: Marcel Ziswiler <[email protected]>

Enable USB device and fastboot support which may be used to load the Toradex Easy Installer FIT image.

Quoted 8 lines

While at it also enable USB mass storage aka UMS support.

Note that the i.MX 8M Plus recovery mode support is based on the USB boot stage of the BOOTROM and does NOT require USB SDP SPL aka serial downloader support.

Applied to u-boot/master, thanks!

Signature · 1 line
Tom