Skip to contentSkip to conversation

phycore-imx8mp: Add USB support

PATCH Superseded Benjamin Hahn 3 participants 7 messages Jan 31, 2024 – Feb 6, 2024

Subsystems (2)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

v2 cover phycore-imx8mp: Add USB support

add support for various USB features like USB storage, USB mass storage as well as booting and flashing emmc via UUU.

---
Changes in v2:
- sync kernel devicetree before making changes
- Link to v1: https://lore.kernel.org/r/[email protected]

---
Benjamin Hahn (4):
imx8mp-phyboard-pollux-rdk: sync with kernel devicetree from v6.8-rc2
phycore-imx8mp: add USB host support
phycore-imx8mp: add USB mass storage support
phycore-imx8mp: add support for booting and flashing emmc via UUU

 .../arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi |   4 +
 arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts        | 162 ++++++++++++++++++++-
 board/phytec/phycore_imx8mp/phycore-imx8mp.c       |   4 +
 configs/phycore-imx8mp_defconfig                   |  33 ++++-
 include/configs/phycore_imx8mp.h                   |   5 +
 5 files changed, 204 insertions(+), 4 deletions(-)

---
base-commit: e7f9e5eb584dd0b5d1b1ff82fe607d6da9940cc6
change-id: 20240126-usb_support-403f47d71ac1

Best regards,

Signature · 1 line
Benjamin Hahn <[email protected]>
#1 lore raw

PATCH v2 1/4 imx8mp-phyboard-pollux-rdk: sync with kernel devicetree from v6.8-rc2

---
 arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts | 162 +++++++++++++++++++++++++++-
 1 file changed, 159 insertions(+), 3 deletions(-)
arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts +159 -3
index 6aa720bafe..c8640cac3e 100644
@@ -19,6 +19,36 @@
 		stdout-path = &uart1;
 	};
 
+	reg_can1_stby: regulator-can1-stby {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flexcan1_reg>;
+		gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "can1-stby";
+	};
+
+	reg_can2_stby: regulator-can2-stby {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flexcan2_reg>;
+		gpio = <&gpio3 21 GPIO_ACTIVE_LOW>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "can2-stby";
+	};
+
+	reg_usb1_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb1_vbus>;
+		gpio = <&gpio1 12 GPIO_ACTIVE_LOW>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb1_host_vbus";
+	};
+
 	reg_usdhc2_vmmc: regulator-usdhc2 {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -57,6 +87,21 @@
 	};
 };
 
+/* CAN FD */
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_can1_stby>;
+	status = "okay";
+};
+
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	xceiver-supply = <&reg_can2_stby>;
+	status = "okay";
+};
+
 &i2c2 {
 	clock-frequency = <400000>;
 	pinctrl-names = "default", "gpio";
@@ -76,15 +121,15 @@
 		compatible = "nxp,pca9533";
 		reg = <0x62>;
 
-		led1 {
+		led-1 {
 			type = <PCA9532_TYPE_LED>;
 		};
 
-		led2 {
+		led-2 {
 			type = <PCA9532_TYPE_LED>;
 		};
 
-		led3 {
+		led-3 {
 			type = <PCA9532_TYPE_LED>;
 		};
 	};
@@ -101,8 +146,51 @@
 	status = "okay";
 };
 
+/* USB1 Host mode Type-A */
+&usb3_phy0 {
+	vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};
+
+&usb3_0 {
+	status = "okay";
+};
+
+&usb_dwc3_0 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+/* USB2 4-port USB3.0 HUB */
+&usb3_phy1 {
+	status = "okay";
+};
+
+&usb3_1 {
+	fsl,permanently-attached;
+	fsl,disable-port-power-control;
+	status = "okay";
+};
+
+&usb_dwc3_1 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+/* RS232/RS485 */
+&uart2 {
+	assigned-clocks = <&clk IMX8MP_CLK_UART2>;
+	assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_80M>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
 /* SD-Card */
 &usdhc2 {
+	assigned-clocks = <&clk IMX8MP_CLK_USDHC2>;
+	assigned-clock-rates = <200000000>;
 	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_pins>;
 	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_pins>;
@@ -113,6 +201,33 @@
 	status = "okay";
 };
 
+&gpio1 {
+	gpio-line-names = "", "", "X_PMIC_WDOG_B", "",
+		"PMIC_SD_VSEL", "", "", "", "", "",
+		"", "", "USB1_OTG_PWR", "", "", "X_nETHPHY_INT";
+};
+
+&gpio2 {
+	gpio-line-names = "", "", "", "",
+		"", "", "", "", "", "",
+		"", "", "X_SD2_CD_B", "", "", "",
+		"", "", "", "SD2_RESET_B";
+};
+
+&gpio3 {
+	gpio-line-names = "", "", "", "",
+		"", "", "", "", "", "",
+		"", "", "", "", "", "",
+		"", "", "", "", "nCAN1_EN", "nCAN2_EN";
+};
+
+&gpio4 {
+	gpio-line-names = "", "", "", "",
+		"", "", "", "", "", "",
+		"", "", "", "", "", "",
+		"", "", "X_PMIC_IRQ_B", "", "nENET0_INT_PWDN";
+};
+
 &iomuxc {
 	pinctrl_eqos: eqosgrp {
 		fsl,pins = <
@@ -134,6 +249,32 @@
 		>;
 	};
 
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI5_RXD2__CAN1_RX		0x154
+			MX8MP_IOMUXC_SAI5_RXD1__CAN1_TX		0x154
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI5_MCLK__CAN2_RX		0x154
+			MX8MP_IOMUXC_SAI5_RXD3__CAN2_TX		0x154
+		>;
+	};
+
+	pinctrl_flexcan1_reg: flexcan1reggrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI5_RXC__GPIO3_IO20	0x154
+		>;
+	};
+
+	pinctrl_flexcan2_reg: flexcan2reggrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI5_RXD0__GPIO3_IO21	0x154
+		>;
+	};
+
 	pinctrl_i2c2: i2c2grp {
 		fsl,pins = <
 			MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL		0x400001c2
@@ -161,6 +302,21 @@
 		>;
 	};
 
+	pinctrl_usb1_vbus: usb1vbusgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO12__GPIO1_IO12     0x10
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX	0x140
+			MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX	0x140
+			MX8MP_IOMUXC_SAI3_RXC__UART2_DCE_CTS	0x140
+			MX8MP_IOMUXC_SAI3_RXD__UART2_DCE_RTS	0x140
+		>;
+	};
+
 	pinctrl_usdhc2_pins: usdhc2-gpiogrp {
 		fsl,pins = <
 			MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12	0x1c4
Signature · 1 line
2.34.1
#2 lore raw

Re: [PATCH v2 1/4] imx8mp-phyboard-pollux-rdk: sync with kernel devicetree from v6.8-rc2

Hello Benjamin,

Am Mittwoch, dem 31.01.2024 um 09:45 +0100 schrieb Benjamin Hahn:

Quoted 1 line

please add a proper patch description. Adding only a subject line ist not enough.

Thanks,
Teresa

Quoted 231 lines

---
 arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts | 162
+++++++++++++++++++++++++++-

 1 file changed, 159 insertions(+), 3 deletions(-)
arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts +0 -0
index 6aa720bafe..c8640cac3e 100644
@@ -19,6 +19,36 @@
                 stdout-path = &uart1;
         };


+       reg_can1_stby: regulator-can1-stby { +               compatible = "regulator-fixed"; +               pinctrl-names = "default";
+               pinctrl-0 = <&pinctrl_flexcan1_reg>; +               gpio = <&gpio3 20 GPIO_ACTIVE_LOW>; +               regulator-max-microvolt = <3300000>; +               regulator-min-microvolt = <3300000>; +               regulator-name = "can1-stby"; +       };

arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts +21 -0
+
+       reg_can2_stby: regulator-can2-stby {
+               compatible = "regulator-fixed";
+               pinctrl-names = "default";
+               pinctrl-0 = <&pinctrl_flexcan2_reg>;
+               gpio = <&gpio3 21 GPIO_ACTIVE_LOW>;
+               regulator-max-microvolt = <3300000>;
+               regulator-min-microvolt = <3300000>;
+               regulator-name = "can2-stby";
+       };
+
+       reg_usb1_vbus: regulator-usb1-vbus {
+               compatible = "regulator-fixed";
+               pinctrl-names = "default";
+               pinctrl-0 = <&pinctrl_usb1_vbus>;
+               gpio = <&gpio1 12 GPIO_ACTIVE_LOW>;
+               regulator-max-microvolt = <5000000>;
+               regulator-min-microvolt = <5000000>;
+               regulator-name = "usb1_host_vbus";
+       };
+

        reg_usdhc2_vmmc: regulator-usdhc2 {
                compatible = "regulator-fixed";
                pinctrl-names = "default";

arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts +0 -0
@@ -57,6 +87,21 @@
         };
  };

arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts +15 -0
+/* CAN FD */
+&flexcan1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_flexcan1>;
+       xceiver-supply = <&reg_can1_stby>;
+       status = "okay";
+};
+
+&flexcan2 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_flexcan2>;
+       xceiver-supply = <&reg_can2_stby>;
+       status = "okay";
+};
+

 &i2c2 {
        clock-frequency = <400000>;
        pinctrl-names = "default", "gpio";

arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts +0 -0
@@ -76,15 +121,15 @@
                 compatible = "nxp,pca9533";
                 reg = <0x62>;


-               led1 {
+               led-1 {
                        type = <PCA9532_TYPE_LED>; };

-               led2 {
+               led-2 {
                        type = <PCA9532_TYPE_LED>; };

-               led3 {
+               led-3 {
                        type = <PCA9532_TYPE_LED>; };
        };

arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts +0 -0
@@ -101,8 +146,51 @@
         status = "okay";
  };

arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts +41 -0
+/* USB1 Host mode Type-A */
+&usb3_phy0 {
+       vbus-supply = <&reg_usb1_vbus>;
+       status = "okay";
+};
+
+&usb3_0 {
+       status = "okay";
+};
+
+&usb_dwc3_0 {
+       dr_mode = "host";
+       status = "okay";
+};
+
+/* USB2 4-port USB3.0 HUB */
+&usb3_phy1 {
+       status = "okay";
+};
+
+&usb3_1 {
+       fsl,permanently-attached;
+       fsl,disable-port-power-control;
+       status = "okay";
+};
+
+&usb_dwc3_1 {
+       dr_mode = "host";
+       status = "okay";
+};
+
+/* RS232/RS485 */
+&uart2 {
+       assigned-clocks = <&clk IMX8MP_CLK_UART2>;
+       assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_80M>;
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_uart2>;
+       uart-has-rtscts;
+       status = "okay";
+};
+

 /* SD-Card */
 &usdhc2 {
+       assigned-clocks = <&clk IMX8MP_CLK_USDHC2>;
+       assigned-clock-rates = <200000000>;
        pinctrl-names = "default", "state_100mhz", "state_200mhz"; pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_pins>; pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_pins>;

arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts +0 -0
@@ -113,6 +201,33 @@
         status = "okay";
  };


+&gpio1 {
+       gpio-line-names = "", "", "X_PMIC_WDOG_B", "", +               "PMIC_SD_VSEL", "", "", "", "", "",
+               "", "", "USB1_OTG_PWR", "", "", "X_nETHPHY_INT";

arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts +23 -0
+};
+
+&gpio2 {
+       gpio-line-names = "", "", "", "",
+               "", "", "", "", "", "",
+               "", "", "X_SD2_CD_B", "", "", "",
+               "", "", "", "SD2_RESET_B";
+};
+
+&gpio3 {
+       gpio-line-names = "", "", "", "",
+               "", "", "", "", "", "",
+               "", "", "", "", "", "",
+               "", "", "", "", "nCAN1_EN", "nCAN2_EN";
+};
+
+&gpio4 {
+       gpio-line-names = "", "", "", "",
+               "", "", "", "", "", "",
+               "", "", "", "", "", "",
+               "", "", "X_PMIC_IRQ_B", "", "nENET0_INT_PWDN";
+};
+

 &iomuxc {
        pinctrl_eqos: eqosgrp {
                fsl,pins = <

arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts +0 -0
@@ -134,6 +249,32 @@
                 >;
         };


+       pinctrl_flexcan1: flexcan1grp {
+               fsl,pins = <
+                       MX8MP_IOMUXC_SAI5_RXD2__CAN1_RX         0x154 +                       MX8MP_IOMUXC_SAI5_RXD1__CAN1_TX         0x154 +               >;
+       };

arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts +20 -0
+
+       pinctrl_flexcan2: flexcan2grp {
+               fsl,pins = <
+                       MX8MP_IOMUXC_SAI5_MCLK__CAN2_RX         0x154
+                       MX8MP_IOMUXC_SAI5_RXD3__CAN2_TX         0x154
+               >;
+       };
+
+       pinctrl_flexcan1_reg: flexcan1reggrp {
+               fsl,pins = <
+                       MX8MP_IOMUXC_SAI5_RXC__GPIO3_IO20       0x154
+               >;
+       };
+
+       pinctrl_flexcan2_reg: flexcan2reggrp {
+               fsl,pins = <
+                       MX8MP_IOMUXC_SAI5_RXD0__GPIO3_IO21      0x154
+               >;
+       };
+

        pinctrl_i2c2: i2c2grp {
                fsl,pins = < MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL         0x400 001c2

arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts +0 -0
@@ -161,6 +302,21 @@
                 >;
         };


+       pinctrl_usb1_vbus: usb1vbusgrp {
+               fsl,pins = <
+                       MX8MP_IOMUXC_GPIO1_IO12__GPIO1_IO12     0x10 +               >;
+       };

arch/arm/dts/imx8mp-phyboard-pollux-rdk.dts +10 -0
+
+       pinctrl_uart2: uart2grp {
+               fsl,pins = <
+                       MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX    0x140
+                       MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX    0x140
+                       MX8MP_IOMUXC_SAI3_RXC__UART2_DCE_CTS    0x140
+                       MX8MP_IOMUXC_SAI3_RXD__UART2_DCE_RTS    0x140
+               >;
+       };
+

        pinctrl_usdhc2_pins: usdhc2-gpiogrp {
                fsl,pins = < MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12       0x1c4

Signature · 5 lines
PHYTEC Messtechnik GmbH | Barcelona-Allee 1 | 55129 Mainz, Germany

Geschäftsführer: Dipl.-Ing. Michael Mitezki, Dipl.-Ing. Bodo Huber,
Dipl.-Ing. (FH) Markus Lickes | Handelsregister Mainz HRB 4656 |
Finanzamt Mainz | St.Nr. 266500608, DE 149059855
#3 lore raw

Re: [PATCH v2 1/4] imx8mp-phyboard-pollux-rdk: sync with kernel devicetree from v6.8-rc2

Quoted 9 lines · Teresa Remmet

Hello Benjamin,

Am Mittwoch, dem 31.01.2024 um 09:45 +0100 schrieb Benjamin Hahn:

Quoted 1 line

please add a proper patch description. Adding only a subject line ist not enough.

One idea that I had is when people are synching with mainline they could put the oneline summary of the stuff that's getting merged. In this case it's the 6 most recent commits.

$ git log --oneline arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
4a58fcdb1818 arm64: dts: imx8mp-phyboard-pollux: Add support for RS232/RS485
3bd7fdcc359e arm64: dts: imx8mp-phyboard-pollux: Add gpio-line-names
f5faa633daf8 arm64: dts: imx8mp-phyboard-pollux: Enable USB support
27c0dc128d04 arm64: dts: imx8mp-phyboard-pollux: Add flexcan support
fa2a1ec50456 arm64: dts: imx8mp-phyboard-pollux: Add missing usdhc clocks assignment
055e38c76388 arm64: dts: imx8mp-phyboard-pollux-rdk: Fix led sub-node names

regards,
dan carpenter

#4 lore raw

PATCH v2 2/4 phycore-imx8mp: add USB host support

In reply to Benjamin Hahn

The phyBOARD Pollux has two USB ports. Add support for USB host and USB storage for the USB1 port.

---
 configs/phycore-imx8mp_defconfig | 10 ++++++++++
 1 file changed, 10 insertions(+)
configs/phycore-imx8mp_defconfig +10 -0
index 519e0cfb3d..74450b957b 100644
@@ -65,6 +65,7 @@ CONFIG_CMD_FUSE=y
 CONFIG_CMD_GPIO=y
 CONFIG_CMD_I2C=y
 CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
@@ -104,6 +105,7 @@ CONFIG_DM_ETH_PHY=y
 CONFIG_FEC_MXC=y
 CONFIG_RGMII=y
 CONFIG_MII=y
+CONFIG_PHY_IMX8MQ_USB=y
 CONFIG_PINCTRL=y
 CONFIG_SPL_PINCTRL=y
 CONFIG_PINCTRL_IMX8M=y
@@ -120,4 +122,12 @@ CONFIG_SPL_SYSRESET=y
 CONFIG_SYSRESET_PSCI=y
 CONFIG_SYSRESET_WATCHDOG=y
 CONFIG_DM_THERMAL=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_XHCI_DWC3_OF_SIMPLE=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_DWC3=y
+CONFIG_USB_DWC3_GENERIC=y
+CONFIG_USB_STORAGE=y
 CONFIG_IMX_WATCHDOG=y
Signature · 1 line
2.34.1
#5 lore raw

PATCH v2 3/4 phycore-imx8mp: add USB mass storage support

In reply to Benjamin Hahn

add support for USB mass storage to USB0 port of phyBOARD Pollux.

tested with "ums 0 mmc 2"

---
 arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi | 4 ++++
 configs/phycore-imx8mp_defconfig                    | 7 +++++++
 2 files changed, 11 insertions(+)
arch/arm/dts/imx8mp-phyboard-pollux-rdk-u-boot.dtsi +4 -0
index 1c7b250549..b4efff27a7 100644
@@ -70,6 +70,10 @@
 	bootph-pre-ram;
 };
 
+&usb_dwc3_0 {
+	dr_mode = "peripheral";
+};
+
 &usdhc2 {
 	bootph-pre-ram;
 };
configs/phycore-imx8mp_defconfig +7 -0
index 74450b957b..e3fe4ed94e 100644
@@ -66,6 +66,7 @@ CONFIG_CMD_GPIO=y
 CONFIG_CMD_I2C=y
 CONFIG_CMD_MMC=y
 CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
 CONFIG_CMD_PING=y
@@ -123,6 +124,7 @@ CONFIG_SYSRESET_PSCI=y
 CONFIG_SYSRESET_WATCHDOG=y
 CONFIG_DM_THERMAL=y
 CONFIG_USB=y
+CONFIG_DM_USB_GADGET=y
 CONFIG_USB_XHCI_HCD=y
 CONFIG_USB_XHCI_DWC3=y
 CONFIG_USB_XHCI_DWC3_OF_SIMPLE=y
@@ -130,4 +132,9 @@ CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_DWC3=y
 CONFIG_USB_DWC3_GENERIC=y
 CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="FSL"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_USB_GADGET_DOWNLOAD=y
 CONFIG_IMX_WATCHDOG=y
Signature · 1 line
2.34.1
#6 lore raw

PATCH v2 4/4 phycore-imx8mp: add support for booting and flashing emmc via UUU

In reply to Benjamin Hahn

add support for Serial Downloader Boot via UUU as well as flashing emmc via UUU on USB0 Port of phyBOARD Pollux.

---
 board/phytec/phycore_imx8mp/phycore-imx8mp.c |  4 ++++
 configs/phycore-imx8mp_defconfig             | 18 ++++++++++++++++--
 include/configs/phycore_imx8mp.h             |  5 +++++
 3 files changed, 25 insertions(+), 2 deletions(-)
board/phytec/phycore_imx8mp/phycore-imx8mp.c +4 -0
index a8f0821437..dbdd6bb793 100644
@@ -46,6 +46,10 @@ int board_late_init(void)
 	case MMC3_BOOT:
 		env_set_ulong("mmcdev", 2);
 		break;
+	case USB_BOOT:
+		printf("Detect USB boot. Will enter fastboot mode!\n");
+		env_set_ulong("dofastboot", 1);
+		break;
 	default:
 		break;
 	}
configs/phycore-imx8mp_defconfig +16 -2
index e3fe4ed94e..0f37286d5d 100644
@@ -27,7 +27,7 @@ CONFIG_FIT_EXTERNAL_OFFSET=0x3000
 CONFIG_SPL_LOAD_FIT=y
 CONFIG_OF_SYSTEM_SETUP=y
 CONFIG_USE_BOOTCOMMAND=y
-CONFIG_BOOTCOMMAND="mmc dev ${mmcdev}; if mmc rescan; then if run loadimage; then run mmcboot; else run netboot; fi; fi;"
+CONFIG_BOOTCOMMAND="if test ${dofastboot} = 1; then fastboot 0; fi; mmc dev ${mmcdev}; if mmc rescan; then if run loadimage; then run mmcboot; else run netboot; fi; fi;"
 CONFIG_DEFAULT_FDT_FILE="oftree"
 CONFIG_SYS_CBSIZE=2048
 CONFIG_SYS_PBSIZE=2074
@@ -66,6 +66,7 @@ CONFIG_CMD_GPIO=y
 CONFIG_CMD_I2C=y
 CONFIG_CMD_MMC=y
 CONFIG_CMD_USB=y
+CONFIG_CMD_USB_SDP=y
 CONFIG_CMD_USB_MASS_STORAGE=y
 CONFIG_CMD_DHCP=y
 CONFIG_CMD_MII=y
@@ -87,6 +88,17 @@ CONFIG_NET_RANDOM_ETHADDR=y
 CONFIG_SPL_DM=y
 CONFIG_CLK_COMPOSITE_CCF=y
 CONFIG_CLK_IMX8MP=y
+CONFIG_USB_FUNCTION_FASTBOOT=y
+CONFIG_FASTBOOT_BUF_ADDR=0x42800000
+CONFIG_FASTBOOT_BUF_SIZE=0x13000000
+CONFIG_FASTBOOT_FLASH=y
+CONFIG_FASTBOOT_UUU_SUPPORT=y
+CONFIG_FASTBOOT_FLASH_MMC_DEV=2
+CONFIG_FASTBOOT_MMC_BOOT_SUPPORT=y
+CONFIG_FASTBOOT_MMC_BOOT1_NAME="mmc2boot0"
+CONFIG_FASTBOOT_MMC_BOOT2_NAME="mmc2boot1"
+CONFIG_FASTBOOT_MMC_USER_SUPPORT=y
+CONFIG_FASTBOOT_MMC_USER_NAME="mmc2"
 CONFIG_MXC_GPIO=y
 CONFIG_DM_I2C=y
 # CONFIG_SPL_DM_I2C is not set
@@ -111,6 +123,9 @@ CONFIG_PINCTRL=y
 CONFIG_SPL_PINCTRL=y
 CONFIG_PINCTRL_IMX8M=y
 CONFIG_SPL_POWER_LEGACY=y
+CONFIG_POWER_DOMAIN=y
+CONFIG_IMX8M_POWER_DOMAIN=y
+CONFIG_IMX8MP_HSIOMIX_BLKCTRL=y
 CONFIG_POWER_PCA9450=y
 CONFIG_DM_REGULATOR=y
 CONFIG_DM_REGULATOR_FIXED=y
@@ -136,5 +151,4 @@ CONFIG_USB_GADGET=y
 CONFIG_USB_GADGET_MANUFACTURER="FSL"
 CONFIG_USB_GADGET_VENDOR_NUM=0x0525
 CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
-CONFIG_USB_GADGET_DOWNLOAD=y
 CONFIG_IMX_WATCHDOG=y
include/configs/phycore_imx8mp.h +5 -0
index d79d364c8e..11a17be7fe 100644
@@ -19,6 +19,11 @@
 	"fdt_addr=0x48000000\0" \
 	"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
 	"ip_dyn=yes\0" \
+	"dofastboot=0\0" \
+	"fastboot_raw_partition_bootloader=64 8128\0" \
+	"fastboot_raw_partition_all=0 4194304\0" \
+	"emmc_dev=2\0" \
+	"sd_dev=1\0" \
 	"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
 	"mmcpart=1\0" \
 	"mmcroot=2\0" \
Signature · 1 line
2.34.1