Skip to contentSkip to conversation

Add RK816 PMIC support

PATCH Superseded Alex Bee 3 participants 9 messages Mar 23, 2024 – Mar 28, 2024

Subsystems (6)

v3 of 4 Superseded Latest is v4 →

lore
Share & tools
lore

Alex Bee

author
#0 lore raw

v3 cover Add RK816 PMIC support

This series aims to add support for Rockchip RK816 PMIC series. As per datasheet it's targeted for RK3126/RK3128 (RK816-1), RK1108 (RK816-2) and PX3-SE (RK816-3) but might be used for other SoCs as well. The MFD consists of an integrated RTC, a GPIO controller, two 32k clock outputs, a power key, 3 buck- and 6 ldo regulators, 3 regulator-switches, and charger with integrated fuel gauge. Charger and fuel gauge are not part of this series. Two of the switches (otg/boost) are part of the binding, but not of the driver. They must only ever be enabled if no battery charging is happening, but it will be enabled automatically if a battery is attached and an external power source is connected. Thus that needs some incorporation of a yet to be added charger driver.
Integration in the existing rk8xx-infrastructure was pretty straightforward and only needed very little tweaking. In order to not further bloat the driver(s) too much with additional #defines I tried to re-use existing ones wherever possible.

The patches are loosely based on the vendor's implementation, verified against the datasheet and tested/measured on a RK3126 board. As they are touching several subsystems I'm sending them (very) early for the 6.10.-cycle.

changes since v1:
- integrated Krzysztof's feedback for the bindings and the resulting driver changes
- fixed a sparse warning

link to v1:
https://lore.kernel.org/lkml/[email protected]/

changes since v2:
- integrated Krzysztof's feedback to v2 of the bindings and the resulting driver changes

link to v2:
https://lore.kernel.org/lkml/[email protected]/

Please see individual patches for details about the changes.

Alex Bee (5):
dt-bindings: mfd: Add rk816 binding
mfd: rk8xx: Add RK816 support
pinctrl: rk805: Add rk816 pinctrl support
regulator: rk808: Support apply_bit for
rk808_set_suspend_voltage_range
regulator: rk808: Add RK816 support

 .../bindings/mfd/rockchip,rk816.yaml          | 274 ++++++++++++++++++
 drivers/mfd/Kconfig                           |   4 +-
 drivers/mfd/rk8xx-core.c                      | 103 +++++++
 drivers/mfd/rk8xx-i2c.c                       |  45 ++-
 drivers/pinctrl/pinctrl-rk805.c               |  69 +++++
 drivers/regulator/rk808-regulator.c           | 218 +++++++++++++-
 include/linux/mfd/rk808.h                     | 141 +++++++++
 7 files changed, 847 insertions(+), 7 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mfd/rockchip,rk816.yaml
Signature · 1 line
2.43.2
author
#1 lore raw

PATCH v3 1/5 dt-bindings: mfd: Add rk816 binding

Add DT binding document for Rockchip's RK816 PMIC

---
changes since v1:
- lowercase/hyphens for regulator node names
- rename "-reg" to "-regulator" to make node names generic
- dropped superfluous description for clock-output-names and wakeup-source
- dropped "|" for text blocks that don't require to preserve formatting
- use full path for $refs
- added pins description to the binding
- added charger function to description

changes since v2:
- dropped "-regulator"-suffix from regulator device names
- use "'"-quotes consistently in the binding
- dropped "pin_fun"-prefix from pin-function names
- added pin to example

 .../bindings/mfd/rockchip,rk816.yaml          | 274 ++++++++++++++++++
 1 file changed, 274 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/rockchip,rk816.yaml
Documentation/devicetree/bindings/mfd/rockchip,rk816.yaml new file +274 -0
new file mode 100644
index 000000000000..b960ded35e99
@@ -0,0 +1,274 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/rockchip,rk816.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: RK816 Power Management Integrated Circuit
+
+maintainers:
+  - Chris Zhong <[email protected]>
+  - Zhang Qing <[email protected]>
+
+description:
+  Rockchip RK816 series PMIC. This device consists of an i2c controlled MFD
+  that includes regulators, a RTC, a GPIO controller, a power button, and a
+  battery charger manager with fuel gauge.
+
+properties:
+  compatible:
+    enum:
+      - rockchip,rk816
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  '#clock-cells':
+    description:
+      See <dt-bindings/clock/rockchip,rk808.h> for clock IDs.
+    const: 1
+
+  clock-output-names:
+    maxItems: 2
+
+  gpio-controller: true
+
+  '#gpio-cells':
+    const: 2
+
+  system-power-controller:
+    type: boolean
+    description:
+      Telling whether or not this PMIC is controlling the system power.
+
+  wakeup-source:
+    type: boolean
+
+  vcc1-supply:
+    description:
+      The input supply for dcdc1.
+
+  vcc2-supply:
+    description:
+      The input supply for dcdc2.
+
+  vcc3-supply:
+    description:
+      The input supply for dcdc3.
+
+  vcc4-supply:
+    description:
+      The input supply for dcdc4.
+
+  vcc5-supply:
+    description:
+      The input supply for ldo1, ldo2, and ldo3.
+
+  vcc6-supply:
+    description:
+      The input supply for ldo4, ldo5, and ldo6.
+
+  vcc7-supply:
+    description:
+      The input supply for boost.
+
+  vcc8-supply:
+    description:
+      The input supply for otg-switch.
+
+  regulators:
+    type: object
+    patternProperties:
+      '^(boost|dcdc[1-4]|ldo[1-6]|otg-switch)$':
+        type: object
+        $ref: /schemas/regulator/regulator.yaml#
+        unevaluatedProperties: false
+    unevaluatedProperties: false
+
+patternProperties:
+  '-pins$':
+    type: object
+    additionalProperties: false
+    $ref: /schemas/pinctrl/pinmux-node.yaml
+
+    properties:
+      function:
+        enum: [gpio, thermistor]
+
+      pins:
+        $ref: /schemas/types.yaml#/definitions/string
+        const: gpio0
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - '#clock-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/pinctrl/rockchip.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        rk816: pmic@1a {
+            compatible = "rockchip,rk816";
+            reg = <0x1a>;
+            interrupt-parent = <&gpio0>;
+            interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;
+            clock-output-names = "xin32k", "rk816-clkout2";
+            pinctrl-names = "default";
+            pinctrl-0 = <&pmic_int_l>;
+            gpio-controller;
+            system-power-controller;
+            wakeup-source;
+            #clock-cells = <1>;
+            #gpio-cells = <2>;
+
+            vcc1-supply = <&vcc_sys>;
+            vcc2-supply = <&vcc_sys>;
+            vcc3-supply = <&vcc_sys>;
+            vcc4-supply = <&vcc_sys>;
+            vcc5-supply = <&vcc33_io>;
+            vcc6-supply = <&vcc_sys>;
+
+            regulators {
+                vdd_cpu: dcdc1 {
+                    regulator-name = "vdd_cpu";
+                    regulator-min-microvolt = <750000>;
+                    regulator-max-microvolt = <1450000>;
+                    regulator-ramp-delay = <6001>;
+                    regulator-initial-mode = <1>;
+                    regulator-always-on;
+                    regulator-boot-on;
+
+                    regulator-state-mem {
+                        regulator-off-in-suspend;
+                    };
+                };
+
+                vdd_logic: dcdc2 {
+                    regulator-name = "vdd_logic";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <1250000>;
+                    regulator-ramp-delay = <6001>;
+                    regulator-initial-mode = <1>;
+                    regulator-always-on;
+                    regulator-boot-on;
+
+                    regulator-state-mem {
+                        regulator-on-in-suspend;
+                        regulator-suspend-microvolt = <1000000>;
+                    };
+                };
+
+                vcc_ddr: dcdc3 {
+                    regulator-name = "vcc_ddr";
+                    regulator-initial-mode = <1>;
+                    regulator-always-on;
+                    regulator-boot-on;
+
+                    regulator-state-mem {
+                        regulator-on-in-suspend;
+                    };
+                };
+
+                vcc33_io: dcdc4 {
+                    regulator-min-microvolt = <3300000>;
+                    regulator-max-microvolt = <3300000>;
+                    regulator-name = "vcc33_io";
+                    regulator-initial-mode = <1>;
+                    regulator-always-on;
+                    regulator-boot-on;
+
+                    regulator-state-mem {
+                        regulator-on-in-suspend;
+                        regulator-suspend-microvolt = <3300000>;
+                    };
+                };
+
+                vccio_pmu: ldo1 {
+                    regulator-min-microvolt = <3300000>;
+                    regulator-max-microvolt = <3300000>;
+                    regulator-name = "vccio_pmu";
+                    regulator-always-on;
+                    regulator-boot-on;
+
+                    regulator-state-mem {
+                        regulator-on-in-suspend;
+                        regulator-suspend-microvolt = <3300000>;
+                    };
+                };
+
+                vcc_tp: ldo2 {
+                    regulator-min-microvolt = <3300000>;
+                    regulator-max-microvolt = <3300000>;
+                    regulator-name = "vcc_tp";
+
+                    regulator-state-mem {
+                        regulator-off-in-suspend;
+                    };
+                };
+
+                vdd_10: ldo3 {
+                    regulator-min-microvolt = <1000000>;
+                    regulator-max-microvolt = <1000000>;
+                    regulator-name = "vdd_10";
+                    regulator-always-on;
+                    regulator-boot-on;
+
+                    regulator-state-mem {
+                        regulator-on-in-suspend;
+                        regulator-suspend-microvolt = <1000000>;
+                    };
+                };
+
+                vcc18_lcd: ldo4 {
+                    regulator-min-microvolt = <1800000>;
+                    regulator-max-microvolt = <1800000>;
+                    regulator-name = "vcc18_lcd";
+
+                    regulator-state-mem {
+                        regulator-on-in-suspend;
+                        regulator-suspend-microvolt = <1800000>;
+                    };
+                };
+
+                vccio_sd: ldo5 {
+                    regulator-min-microvolt = <1800000>;
+                    regulator-max-microvolt = <3300000>;
+                    regulator-name = "vccio_sd";
+
+                    regulator-state-mem {
+                        regulator-on-in-suspend;
+                        regulator-suspend-microvolt = <3300000>;
+                    };
+                };
+
+                vdd10_lcd: ldo6 {
+                    regulator-min-microvolt = <1000000>;
+                    regulator-max-microvolt = <1000000>;
+                    regulator-name = "vdd10_lcd";
+
+                    regulator-state-mem {
+                        regulator-on-in-suspend;
+                        regulator-suspend-microvolt = <1000000>;
+                    };
+                };
+            };
+
+            rk816_gpio_pins: gpio-pins {
+                function = "gpio";
+                pins = "gpio0";
+            };
+        };
+    };
Signature · 1 line
2.43.2
Reviewed-by on v3 1/5
#2 lore raw

Re: [PATCH v3 1/5] dt-bindings: mfd: Add rk816 binding

Documentation/devicetree/bindings/mfd/rockchip,rk816.yaml line 88

Quoted 12 lines · Alex Bee

Add DT binding document for Rockchip's RK816 PMIC

Documentation/devicetree/bindings/mfd/rockchip,rk816.yaml new file +7 -0
+  regulators:
+    type: object
+    patternProperties:
+      '^(boost|dcdc[1-4]|ldo[1-6]|otg-switch)$':
+        type: object
+        $ref: /schemas/regulator/regulator.yaml#
+        unevaluatedProperties: false

This is good.

Quoted 1 line

+ unevaluatedProperties: false

I missed it last time, apologies. This (second) unevaluated should be "additionalProperties: false" instead.

With this fixed:

Best regards,
Krzysztof

author
#3 lore raw

Re: [PATCH v3 1/5] dt-bindings: mfd: Add rk816 binding

Am 23.03.24 um 15:32 schrieb Krzysztof Kozlowski:

Quoted 12 lines · Alex Bee

Documentation/devicetree/bindings/mfd/rockchip,rk816.yaml line 88

Quoted 11 lines

Add DT binding document for Rockchip's RK816 PMIC

Documentation/devicetree/bindings/mfd/rockchip,rk816.yaml new file +7 -0
+  regulators:
+    type: object
+    patternProperties:
+      '^(boost|dcdc[1-4]|ldo[1-6]|otg-switch)$':
+        type: object
+        $ref: /schemas/regulator/regulator.yaml#
+        unevaluatedProperties: false
Quoted 5 lines

This is good.

Quoted 1 line

+ unevaluatedProperties: false

I missed it last time, apologies. This (second) unevaluated should be "additionalProperties: false" instead.

Alright. Since there are no driver changes required for this change, I'll give the other maintainers some time to review and fix it alongside in v4.

Alex

Quoted 8 lines

With this fixed:

Best regards,
Krzysztof

author
#4 lore raw

PATCH v3 2/5 mfd: rk8xx: Add RK816 support

In reply to Alex Bee

This integrates RK816 support in the this existing rk8xx mfd driver.

This version has unaligned interrupt registers, which requires to define a separate get_irq_reg callback for the regmap. Apart from that the integration is straightforward and the existing structures can be used as is. The initialization sequence has been taken from vendor kernel.

---
chnages since v1:
- un-constify rk816_get_irq_reg's return type

 drivers/mfd/Kconfig       |   4 +-
 drivers/mfd/rk8xx-core.c  | 103 ++++++++++++++++++++++++++++
 drivers/mfd/rk8xx-i2c.c   |  45 +++++++++++-
 include/linux/mfd/rk808.h | 141 ++++++++++++++++++++++++++++++++++++++
 4 files changed, 290 insertions(+), 3 deletions(-)
drivers/mfd/Kconfig +2 -2
index 4b023ee229cf..2e7286cc98e4 100644
@@ -1225,7 +1225,7 @@ config MFD_RK8XX
 	select MFD_CORE
 
 config MFD_RK8XX_I2C
-	tristate "Rockchip RK805/RK808/RK809/RK817/RK818 Power Management Chip"
+	tristate "Rockchip RK805/RK808/RK809/RK816/RK817/RK818 Power Management Chip"
 	depends on I2C && OF
 	select MFD_CORE
 	select REGMAP_I2C
@@ -1233,7 +1233,7 @@ config MFD_RK8XX_I2C
 	select MFD_RK8XX
 	help
 	  If you say yes here you get support for the RK805, RK808, RK809,
-	  RK817 and RK818 Power Management chips.
+	  RK816, RK817 and RK818 Power Management chips.
 	  This driver provides common support for accessing the device
 	  through I2C interface. The device supports multiple sub-devices
 	  including interrupts, RTC, LDO & DCDC regulators, and onkey.
drivers/mfd/rk8xx-core.c +103 -0

145 lines not on this page · raw message

drivers/mfd/rk8xx-i2c.c +44 -1

74 lines not on this page · raw message

include/linux/mfd/rk808.h +141 -0

159 lines not on this page · raw message

Signature · 1 line
2.43.2
maintainer
#5 lore raw

Re: [PATCH v3 2/5] mfd: rk8xx: Add RK816 support

Quoted 56 lines · Alex Bee

This integrates RK816 support in the this existing rk8xx mfd driver.

This version has unaligned interrupt registers, which requires to define a separate get_irq_reg callback for the regmap. Apart from that the integration is straightforward and the existing structures can be used as is. The initialization sequence has been taken from vendor kernel.

---
chnages since v1:
- un-constify rk816_get_irq_reg's return type

 drivers/mfd/Kconfig       |   4 +-
 drivers/mfd/rk8xx-core.c  | 103 ++++++++++++++++++++++++++++
 drivers/mfd/rk8xx-i2c.c   |  45 +++++++++++-
 include/linux/mfd/rk808.h | 141 ++++++++++++++++++++++++++++++++++++++
 4 files changed, 290 insertions(+), 3 deletions(-)
drivers/mfd/Kconfig +2 -2
index 4b023ee229cf..2e7286cc98e4 100644
@@ -1225,7 +1225,7 @@ config MFD_RK8XX
 	select MFD_CORE
 
 config MFD_RK8XX_I2C
-	tristate "Rockchip RK805/RK808/RK809/RK817/RK818 Power Management Chip"
+	tristate "Rockchip RK805/RK808/RK809/RK816/RK817/RK818 Power Management Chip"
 	depends on I2C && OF
 	select MFD_CORE
 	select REGMAP_I2C
@@ -1233,7 +1233,7 @@ config MFD_RK8XX_I2C
 	select MFD_RK8XX
 	help
 	  If you say yes here you get support for the RK805, RK808, RK809,
-	  RK817 and RK818 Power Management chips.
+	  RK816, RK817 and RK818 Power Management chips.
 	  This driver provides common support for accessing the device
 	  through I2C interface. The device supports multiple sub-devices
 	  including interrupts, RTC, LDO & DCDC regulators, and onkey.
drivers/mfd/rk8xx-core.c +4 -0
index e2261b68b844..c68a380332e7 100644
@@ -28,6 +28,10 @@ static const struct resource rtc_resources[] = {
 	DEFINE_RES_IRQ(RK808_IRQ_RTC_ALARM),
 };
 
+static const struct resource rk816_rtc_resources[] = {
+	DEFINE_RES_IRQ(RK816_IRQ_RTC_ALARM),
+};
+
 static const struct resource rk817_rtc_resources[] = {
 	DEFINE_RES_IRQ(RK817_IRQ_RTC_ALARM),
 };

drivers/mfd/rk8xx-core.c static const struct mfd_cell rk808s[] = { · line 98

Quoted 8 lines
drivers/mfd/rk8xx-core.c +5 -0
@@ -87,6 +91,21 @@ static const struct mfd_cell rk808s[] = {
 	},
 };
 
+static const struct mfd_cell rk816s[] = {
+	{ .name = "rk805-pinctrl", },
+	{ .name = "rk808-clkout", },
+	{ .name = "rk808-regulator", },
+	{	.name = "rk805-pwrkey",

Newline after the '{'.

Quoted 32 lines
drivers/mfd/rk8xx-core.c +21 -0
+		.num_resources = ARRAY_SIZE(rk805_key_resources),
+		.resources = rk805_key_resources,
+	},
+	{
+		.name = "rk808-rtc",
+		.num_resources = ARRAY_SIZE(rk816_rtc_resources),
+		.resources = rk816_rtc_resources,
+	},
+};
+
 static const struct mfd_cell rk817s[] = {
 	{ .name = "rk808-clkout", },
 	{ .name = "rk808-regulator", },
@@ -148,6 +167,17 @@ static const struct rk808_reg_data rk808_pre_init_reg[] = {
 						    VB_LO_SEL_3500MV },
 };
 
+static const struct rk808_reg_data rk816_pre_init_reg[] = {
+	{ RK818_BUCK1_CONFIG_REG, RK817_RAMP_RATE_MASK,
+				  RK817_RAMP_RATE_12_5MV_PER_US },
+	{ RK818_BUCK2_CONFIG_REG, RK817_RAMP_RATE_MASK,
+				  RK817_RAMP_RATE_12_5MV_PER_US },
+	{ RK818_BUCK4_CONFIG_REG, BUCK_ILMIN_MASK,  BUCK_ILMIN_250MA },
+	{ RK808_THERMAL_REG, TEMP_HOTDIE_MSK, TEMP105C},
+	{ RK808_VB_MON_REG, VBAT_LOW_VOL_MASK | VBAT_LOW_ACT_MASK,
+			    RK808_VBAT_LOW_3V0 | EN_VABT_LOW_SHUT_DOWN },
+};
+
 static const struct rk808_reg_data rk817_pre_init_reg[] = {
 	{RK817_RTC_CTRL_REG, RTC_STOP, RTC_STOP},
 	/* Codec specific registers */

drivers/mfd/rk8xx-core.c static const struct regmap_irq rk808_irqs[] = { · line 384

Quoted 5 lines
drivers/mfd/rk8xx-core.c +2 -0
@@ -350,6 +380,59 @@ static const struct regmap_irq rk808_irqs[] = {
 	},
 };
 
+static const unsigned int rk816_irq_status_offsets[] = {
+	(RK816_INT_STS_REG1 - RK816_INT_STS_REG1),

Turn this into a macro please.

Quoted 347 lines
drivers/mfd/rk8xx-core.c +71 -0
+	(RK816_INT_STS_REG2 - RK816_INT_STS_REG1),
+	(RK816_INT_STS_REG3 - RK816_INT_STS_REG1),
+};
+
+static const unsigned int rk816_irq_mask_offsets[] = {
+	(RK816_INT_STS_MSK_REG1 - RK816_INT_STS_MSK_REG1),
+	(RK816_INT_STS_MSK_REG2 - RK816_INT_STS_MSK_REG1),
+	(RK816_INT_STS_MSK_REG3 - RK816_INT_STS_MSK_REG1),
+};
+
+static unsigned int rk816_get_irq_reg(struct regmap_irq_chip_data *data,
+				      unsigned int base, int index)
+{
+	unsigned int irq_reg = base;
+
+	switch (base) {
+	case RK816_INT_STS_REG1:
+		irq_reg += rk816_irq_status_offsets[index];
+		break;
+	case RK816_INT_STS_MSK_REG1:
+		irq_reg += rk816_irq_mask_offsets[index];
+		break;
+	}
+
+	return irq_reg;
+};
+
+static const struct regmap_irq rk816_irqs[] = {
+	/* INT_STS_REG1 IRQs */
+	REGMAP_IRQ_REG(RK816_IRQ_PWRON_FALL, 0, RK816_INT_STS_PWRON_FALL),
+	REGMAP_IRQ_REG(RK816_IRQ_PWRON_RISE, 0, RK816_INT_STS_PWRON_RISE),
+
+	/* INT_STS_REG2 IRQs  */
+	REGMAP_IRQ_REG(RK816_IRQ_VB_LOW, 1, RK816_INT_STS_VB_LOW),
+	REGMAP_IRQ_REG(RK816_IRQ_PWRON, 1, RK816_INT_STS_PWRON),
+	REGMAP_IRQ_REG(RK816_IRQ_PWRON_LP, 1, RK816_INT_STS_PWRON_LP),
+	REGMAP_IRQ_REG(RK816_IRQ_HOTDIE, 1, RK816_INT_STS_HOTDIE),
+	REGMAP_IRQ_REG(RK816_IRQ_RTC_ALARM, 1, RK816_INT_STS_RTC_ALARM),
+	REGMAP_IRQ_REG(RK816_IRQ_RTC_PERIOD, 1, RK816_INT_STS_RTC_PERIOD),
+	REGMAP_IRQ_REG(RK816_IRQ_USB_OV, 1, RK816_INT_STS_USB_OV),
+
+	/* INT_STS3 IRQs */
+	REGMAP_IRQ_REG(RK816_IRQ_PLUG_IN, 2, RK816_INT_STS_PLUG_IN),
+	REGMAP_IRQ_REG(RK816_IRQ_PLUG_OUT, 2, RK816_INT_STS_PLUG_OUT),
+	REGMAP_IRQ_REG(RK816_IRQ_CHG_OK, 2, RK816_INT_STS_CHG_OK),
+	REGMAP_IRQ_REG(RK816_IRQ_CHG_TE, 2, RK816_INT_STS_CHG_TE),
+	REGMAP_IRQ_REG(RK816_IRQ_CHG_TS, 2, RK816_INT_STS_CHG_TS),
+	REGMAP_IRQ_REG(RK816_IRQ_CHG_CVTLIM, 2, RK816_INT_STS_CHG_CVTLIM),
+	REGMAP_IRQ_REG(RK816_IRQ_DISCHG_ILIM, 2, RK816_INT_STS_DISCHG_ILIM),
+};
+
 static const struct regmap_irq rk818_irqs[] = {
 	/* INT_STS */
 	[RK818_IRQ_VOUT_LO] = {
@@ -482,6 +565,18 @@ static const struct regmap_irq_chip rk808_irq_chip = {
 	.init_ack_masked = true,
 };
 
+static const struct regmap_irq_chip rk816_irq_chip = {
+	.name = "rk816",
+	.irqs = rk816_irqs,
+	.num_irqs = ARRAY_SIZE(rk816_irqs),
+	.num_regs = 3,
+	.get_irq_reg = rk816_get_irq_reg,
+	.status_base = RK816_INT_STS_REG1,
+	.mask_base = RK816_INT_STS_MSK_REG1,
+	.ack_base = RK816_INT_STS_REG1,
+	.init_ack_masked = true,
+};
+
 static struct regmap_irq_chip rk817_irq_chip = {
 	.name = "rk817",
 	.irqs = rk817_irqs,
@@ -530,6 +625,7 @@ static int rk808_power_off(struct sys_off_data *data)
 		reg = RK817_SYS_CFG(3);
 		bit = DEV_OFF;
 		break;
+	case RK816_ID:
 	case RK818_ID:
 		reg = RK818_DEVCTRL_REG;
 		bit = DEV_OFF;
@@ -637,6 +733,13 @@ int rk8xx_probe(struct device *dev, int variant, unsigned int irq, struct regmap
 		cells = rk808s;
 		nr_cells = ARRAY_SIZE(rk808s);
 		break;
+	case RK816_ID:
+		rk808->regmap_irq_chip = &rk816_irq_chip;
+		pre_init_reg = rk816_pre_init_reg;
+		nr_pre_init_regs = ARRAY_SIZE(rk816_pre_init_reg);
+		cells = rk816s;
+		nr_cells = ARRAY_SIZE(rk816s);
+		break;
 	case RK818_ID:
 		rk808->regmap_irq_chip = &rk818_irq_chip;
 		pre_init_reg = rk818_pre_init_reg;
drivers/mfd/rk8xx-i2c.c +44 -1
index 75b5cf09d5a0..69a6b297d723 100644
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * Rockchip RK808/RK818 Core (I2C) driver
+ * Rockchip RK805/RK808/RK816/RK817/RK818 Core (I2C) driver
  *
  * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
  * Copyright (C) 2016 PHYTEC Messtechnik GmbH
@@ -49,6 +49,35 @@ static bool rk808_is_volatile_reg(struct device *dev, unsigned int reg)
 	return false;
 }
 
+static bool rk816_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+	/*
+	 * Technically the ROUND_30s bit makes RTC_CTRL_REG volatile, but
+	 * we don't use that feature.  It's better to cache.
+	 */
+
+	switch (reg) {
+	case RK808_SECONDS_REG ... RK808_WEEKS_REG:
+	case RK808_RTC_STATUS_REG:
+	case RK808_VB_MON_REG:
+	case RK808_THERMAL_REG:
+	case RK816_DCDC_EN_REG1:
+	case RK816_DCDC_EN_REG2:
+	case RK816_INT_STS_REG1:
+	case RK816_INT_STS_REG2:
+	case RK816_INT_STS_REG3:
+	case RK808_DEVCTRL_REG:
+	case RK816_SUP_STS_REG:
+	case RK816_GGSTS_REG:
+	case RK816_ZERO_CUR_ADC_REGH:
+	case RK816_ZERO_CUR_ADC_REGL:
+	case RK816_GASCNT_REG(0) ... RK816_BAT_VOL_REGL:
+		return true;
+	}
+
+	return false;
+}
+
 static bool rk817_is_volatile_reg(struct device *dev, unsigned int reg)
 {
 	/*
@@ -100,6 +129,14 @@ static const struct regmap_config rk808_regmap_config = {
 	.volatile_reg = rk808_is_volatile_reg,
 };
 
+static const struct regmap_config rk816_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.max_register = RK816_DATA_REG(18),
+	.cache_type = REGCACHE_MAPLE,
+	.volatile_reg = rk816_is_volatile_reg,
+};
+
 static const struct regmap_config rk817_regmap_config = {
 	.reg_bits = 8,
 	.val_bits = 8,
@@ -123,6 +160,11 @@ static const struct rk8xx_i2c_platform_data rk809_data = {
 	.variant = RK809_ID,
 };
 
+static const struct rk8xx_i2c_platform_data rk816_data = {
+	.regmap_cfg = &rk816_regmap_config,
+	.variant = RK816_ID,
+};
+
 static const struct rk8xx_i2c_platform_data rk817_data = {
 	.regmap_cfg = &rk817_regmap_config,
 	.variant = RK817_ID,
@@ -161,6 +203,7 @@ static const struct of_device_id rk8xx_i2c_of_match[] = {
 	{ .compatible = "rockchip,rk805", .data = &rk805_data },
 	{ .compatible = "rockchip,rk808", .data = &rk808_data },
 	{ .compatible = "rockchip,rk809", .data = &rk809_data },
+	{ .compatible = "rockchip,rk816", .data = &rk816_data },
 	{ .compatible = "rockchip,rk817", .data = &rk817_data },
 	{ .compatible = "rockchip,rk818", .data = &rk818_data },
 	{ },
include/linux/mfd/rk808.h +141 -0
index 78e167a92483..b90d1c278790 100644
@@ -113,6 +113,145 @@ enum rk808_reg {
 #define RK808_INT_STS_MSK_REG2	0x4f
 #define RK808_IO_POL_REG	0x50
 
+/* RK816 */
+enum rk816_reg {
+	RK816_ID_DCDC1,
+	RK816_ID_DCDC2,
+	RK816_ID_DCDC3,
+	RK816_ID_DCDC4,
+	RK816_ID_LDO1,
+	RK816_ID_LDO2,
+	RK816_ID_LDO3,
+	RK816_ID_LDO4,
+	RK816_ID_LDO5,
+	RK816_ID_LDO6,
+	RK816_ID_BOOST,
+	RK816_ID_OTG_SW,
+};
+
+enum rk816_irqs {
+	/* INT_STS_REG1 */
+	RK816_IRQ_PWRON_FALL,
+	RK816_IRQ_PWRON_RISE,
+
+	/* INT_STS_REG2 */
+	RK816_IRQ_VB_LOW,
+	RK816_IRQ_PWRON,
+	RK816_IRQ_PWRON_LP,
+	RK816_IRQ_HOTDIE,
+	RK816_IRQ_RTC_ALARM,
+	RK816_IRQ_RTC_PERIOD,
+	RK816_IRQ_USB_OV,
+
+	/* INT_STS_REG3 */
+	RK816_IRQ_PLUG_IN,
+	RK816_IRQ_PLUG_OUT,
+	RK816_IRQ_CHG_OK,
+	RK816_IRQ_CHG_TE,
+	RK816_IRQ_CHG_TS,
+	RK816_IRQ_CHG_CVTLIM,
+	RK816_IRQ_DISCHG_ILIM,
+};
+
+/* power channel registers */
+#define RK816_DCDC_EN_REG1		0x23
+
+#define RK816_DCDC_EN_REG2		0x24
+#define	RK816_BOOST_EN			BIT(1)
+#define RK816_OTG_EN			BIT(2)
+#define	RK816_BOOST_EN_MSK		BIT(5)
+#define RK816_OTG_EN_MSK		BIT(6)
+#define RK816_BUCK_DVS_CONFIRM		BIT(7)
+
+#define RK816_LDO_EN_REG1		0x27
+
+#define RK816_LDO_EN_REG2		0x28
+
+/* interrupt registers and irq definitions */
+#define RK816_INT_STS_REG1		0x49
+#define RK816_INT_STS_MSK_REG1		0x4a
+#define RK816_INT_STS_PWRON_FALL	BIT(5)
+#define RK816_INT_STS_PWRON_RISE	BIT(6)
+
+#define RK816_INT_STS_REG2		0x4c
+#define RK816_INT_STS_MSK_REG2		0x4d
+#define RK816_INT_STS_VB_LOW		BIT(1)
+#define RK816_INT_STS_PWRON		BIT(2)
+#define RK816_INT_STS_PWRON_LP		BIT(3)
+#define RK816_INT_STS_HOTDIE		BIT(4)
+#define RK816_INT_STS_RTC_ALARM		BIT(5)
+#define RK816_INT_STS_RTC_PERIOD	BIT(6)
+#define RK816_INT_STS_USB_OV		BIT(7)
+
+#define RK816_INT_STS_REG3		0x4e
+#define RK816_INT_STS_MSK_REG3		0x4f
+#define RK816_INT_STS_PLUG_IN		BIT(0)
+#define RK816_INT_STS_PLUG_OUT		BIT(1)
+#define RK816_INT_STS_CHG_OK		BIT(2)
+#define RK816_INT_STS_CHG_TE		BIT(3)
+#define RK816_INT_STS_CHG_TS		BIT(4)
+#define RK816_INT_STS_CHG_CVTLIM	BIT(6)
+#define RK816_INT_STS_DISCHG_ILIM	BIT(7)
+
+/* charger, boost and OTG registers */
+#define RK816_OTG_BUCK_LDO_CONFIG_REG	0x2a
+#define RK816_CHRG_CONFIG_REG		0x2b
+#define RK816_BOOST_ON_VESL_REG		0x54
+#define RK816_BOOST_SLP_VSEL_REG	0x55
+#define RK816_CHRG_BOOST_CONFIG_REG	0x9a
+#define RK816_SUP_STS_REG		0xa0
+#define RK816_USB_CTRL_REG		0xa1
+#define RK816_CHRG_CTRL(x)		(0xa3 + (x))
+#define RK816_BAT_CTRL_REG		0xa6
+#define RK816_BAT_HTS_TS_REG		0xa8
+#define RK816_BAT_LTS_TS_REG		0xa9
+
+/* adc and fuel gauge registers */
+#define RK816_TS_CTRL_REG		0xac
+#define RK816_ADC_CTRL_REG		0xad
+#define RK816_GGCON_REG			0xb0
+#define RK816_GGSTS_REG			0xb1
+#define RK816_ZERO_CUR_ADC_REGH		0xb2
+#define RK816_ZERO_CUR_ADC_REGL		0xb3
+#define RK816_GASCNT_CAL_REG(x)		(0xb7 - (x))
+#define RK816_GASCNT_REG(x)		(0xbb - (x))
+#define RK816_BAT_CUR_AVG_REGH		0xbc
+#define RK816_BAT_CUR_AVG_REGL		0xbd
+#define RK816_TS_ADC_REGH		0xbe
+#define RK816_TS_ADC_REGL		0xbf
+#define RK816_USB_ADC_REGH		0xc0
+#define RK816_USB_ADC_REGL		0xc1
+#define RK816_BAT_OCV_REGH		0xc2
+#define RK816_BAT_OCV_REGL		0xc3
+#define RK816_BAT_VOL_REGH		0xc4
+#define RK816_BAT_VOL_REGL		0xc5
+#define RK816_RELAX_ENTRY_THRES_REGH	0xc6
+#define RK816_RELAX_ENTRY_THRES_REGL	0xc7
+#define RK816_RELAX_EXIT_THRES_REGH	0xc8
+#define RK816_RELAX_EXIT_THRES_REGL	0xc9
+#define RK816_RELAX_VOL1_REGH		0xca
+#define RK816_RELAX_VOL1_REGL		0xcb
+#define RK816_RELAX_VOL2_REGH		0xcc
+#define RK816_RELAX_VOL2_REGL		0xcd
+#define RK816_RELAX_CUR1_REGH		0xce
+#define RK816_RELAX_CUR1_REGL		0xcf
+#define RK816_RELAX_CUR2_REGH		0xd0
+#define RK816_RELAX_CUR2_REGL		0xd1
+#define RK816_CAL_OFFSET_REGH		0xd2
+#define RK816_CAL_OFFSET_REGL		0xd3
+#define RK816_NON_ACT_TIMER_CNT_REG	0xd4
+#define RK816_VCALIB0_REGH		0xd5
+#define RK816_VCALIB0_REGL		0xd6
+#define RK816_VCALIB1_REGH		0xd7
+#define RK816_VCALIB1_REGL		0xd8
+#define RK816_FCC_GASCNT_REG(x)		(0xdc - (x))
+#define RK816_IOFFSET_REGH		0xdd
+#define RK816_IOFFSET_REGL		0xde
+#define RK816_SLEEP_CON_SAMP_CUR_REG	0xdf
+
+/* general purpose data registers 0xe0 ~ 0xf2 */
+#define RK816_DATA_REG(x)		(0xe0 + (x))
+
 /* RK818 */
 #define RK818_DCDC1			0
 #define RK818_LDO1			4
@@ -791,6 +930,7 @@ enum rk806_dvs_mode {
 #define VOUT_LO_INT	BIT(0)
 #define CLK32KOUT2_EN	BIT(0)
 
+#define TEMP105C			0x08
 #define TEMP115C			0x0c
 #define TEMP_HOTDIE_MSK			0x0c
 #define SLP_SD_MSK			(0x3 << 2)
@@ -1191,6 +1331,7 @@ enum {
 	RK806_ID = 0x8060,
 	RK808_ID = 0x0000,
 	RK809_ID = 0x8090,
+	RK816_ID = 0x8160,
 	RK817_ID = 0x8170,
 	RK818_ID = 0x8180,
 };
Signature · 1 line
2.43.2
Signature · 1 line
Lee Jones [李琼斯]
author
#6 lore raw

PATCH v3 3/5 pinctrl: rk805: Add rk816 pinctrl support

In reply to Alex Bee

This adds support for RK816 to the exising rk805 pinctrl driver

It has a single pin which can be configured as input from a thermistor (for instance in an attached battery) or as a gpio.

---
changes since v1:
- rename pin-function names according to the updated binding
- added missing fun_reg for rk816_gpio_cfgs

changes since v2:
- aligned pin-function names with binding (dropped "pin_fun"-prefix)

 drivers/pinctrl/pinctrl-rk805.c | 69 +++++++++++++++++++++++++++++++++
 1 file changed, 69 insertions(+)
drivers/pinctrl/pinctrl-rk805.c +69 -0
index 56d916f2cee6..c42f1bf93404 100644
@@ -93,6 +93,11 @@ enum rk806_pinmux_option {
 	RK806_PINMUX_FUN5,
 };
 
+enum rk816_pinmux_option {
+	RK816_PINMUX_THERMISTOR,
+	RK816_PINMUX_GPIO,
+};
+
 enum {
 	RK805_GPIO0,
 	RK805_GPIO1,
@@ -104,6 +109,10 @@ enum {
 	RK806_GPIO_DVS3
 };
 
+enum {
+	RK816_GPIO0,
+};
+
 static const char *const rk805_gpio_groups[] = {
 	"gpio0",
 	"gpio1",
@@ -115,6 +124,10 @@ static const char *const rk806_gpio_groups[] = {
 	"gpio_pwrctrl3",
 };
 
+static const char *const rk816_gpio_groups[] = {
+	"gpio0",
+};
+
 /* RK805: 2 output only GPIOs */
 static const struct pinctrl_pin_desc rk805_pins_desc[] = {
 	PINCTRL_PIN(RK805_GPIO0, "gpio0"),
@@ -128,6 +141,11 @@ static const struct pinctrl_pin_desc rk806_pins_desc[] = {
 	PINCTRL_PIN(RK806_GPIO_DVS3, "gpio_pwrctrl3"),
 };
 
+/* RK816 */
+static const struct pinctrl_pin_desc rk816_pins_desc[] = {
+	PINCTRL_PIN(RK816_GPIO0, "gpio0"),
+};
+
 static const struct rk805_pin_function rk805_pin_functions[] = {
 	{
 		.name = "gpio",
@@ -176,6 +194,21 @@ static const struct rk805_pin_function rk806_pin_functions[] = {
 	},
 };
 
+static const struct rk805_pin_function rk816_pin_functions[] = {
+	{
+		.name = "gpio",
+		.groups = rk816_gpio_groups,
+		.ngroups = ARRAY_SIZE(rk816_gpio_groups),
+		.mux_option = RK816_PINMUX_GPIO,
+	},
+	{
+		.name = "thermistor",
+		.groups = rk816_gpio_groups,
+		.ngroups = ARRAY_SIZE(rk816_gpio_groups),
+		.mux_option = RK816_PINMUX_THERMISTOR,
+	},
+};
+
 static const struct rk805_pin_group rk805_pin_groups[] = {
 	{
 		.name = "gpio0",
@@ -207,6 +240,14 @@ static const struct rk805_pin_group rk806_pin_groups[] = {
 	}
 };
 
+static const struct rk805_pin_group rk816_pin_groups[] = {
+	{
+		.name = "gpio0",
+		.pins = { RK816_GPIO0 },
+		.npins = 1,
+	},
+};
+
 #define RK805_GPIO0_VAL_MSK	BIT(0)
 #define RK805_GPIO1_VAL_MSK	BIT(1)
 
@@ -255,6 +296,20 @@ static struct rk805_pin_config rk806_gpio_cfgs[] = {
 	}
 };
 
+#define RK816_FUN_MASK		BIT(2)
+#define RK816_VAL_MASK		BIT(3)
+#define RK816_DIR_MASK		BIT(4)
+
+static struct rk805_pin_config rk816_gpio_cfgs[] = {
+	{
+		.fun_reg = RK818_IO_POL_REG,
+		.fun_msk = RK816_FUN_MASK,
+		.reg = RK818_IO_POL_REG,
+		.val_msk = RK816_VAL_MASK,
+		.dir_msk = RK816_DIR_MASK,
+	},
+};
+
 /* generic gpio chip */
 static int rk805_gpio_get(struct gpio_chip *chip, unsigned int offset)
 {
@@ -439,6 +494,8 @@ static int rk805_pinctrl_gpio_request_enable(struct pinctrl_dev *pctldev,
 		return _rk805_pinctrl_set_mux(pctldev, offset, RK805_PINMUX_GPIO);
 	case RK806_ID:
 		return _rk805_pinctrl_set_mux(pctldev, offset, RK806_PINMUX_FUN5);
+	case RK816_ID:
+		return _rk805_pinctrl_set_mux(pctldev, offset, RK816_PINMUX_GPIO);
 	}
 
 	return -ENOTSUPP;
@@ -588,6 +645,18 @@ static int rk805_pinctrl_probe(struct platform_device *pdev)
 		pci->pin_cfg = rk806_gpio_cfgs;
 		pci->gpio_chip.ngpio = ARRAY_SIZE(rk806_gpio_cfgs);
 		break;
+	case RK816_ID:
+		pci->pins = rk816_pins_desc;
+		pci->num_pins = ARRAY_SIZE(rk816_pins_desc);
+		pci->functions = rk816_pin_functions;
+		pci->num_functions = ARRAY_SIZE(rk816_pin_functions);
+		pci->groups = rk816_pin_groups;
+		pci->num_pin_groups = ARRAY_SIZE(rk816_pin_groups);
+		pci->pinctrl_desc.pins = rk816_pins_desc;
+		pci->pinctrl_desc.npins = ARRAY_SIZE(rk816_pins_desc);
+		pci->pin_cfg = rk816_gpio_cfgs;
+		pci->gpio_chip.ngpio = ARRAY_SIZE(rk816_gpio_cfgs);
+		break;
 	default:
 		dev_err(&pdev->dev, "unsupported RK805 ID %lu\n",
 			pci->rk808->variant);
Signature · 1 line
2.43.2
author
#7 lore raw

PATCH v3 4/5 regulator: rk808: Support apply_bit for rk808_set_suspend_voltage_range

In reply to Alex Bee

rk808_set_suspend_voltage_range currently does not account the existence of apply_bit/apply_reg.

This adds support for those in same way it is done in regulator_set_voltage_sel_regmap and is required for the upcoming RK816 support

---
changes since v1:
- none

 drivers/regulator/rk808-regulator.c | 16 +++++++++++++---
 1 file changed, 13 insertions(+), 3 deletions(-)
drivers/regulator/rk808-regulator.c +13 -3
index d89ae7f16d7a..a6a563e402d0 100644
@@ -534,15 +534,25 @@ static int rk808_set_suspend_voltage_range(struct regulator_dev *rdev, int uv)
 {
 	unsigned int reg;
 	int sel = regulator_map_voltage_linear_range(rdev, uv, uv);
+	int ret;
 
 	if (sel < 0)
 		return -EINVAL;
 
 	reg = rdev->desc->vsel_reg + RK808_SLP_REG_OFFSET;
 
-	return regmap_update_bits(rdev->regmap, reg,
-				  rdev->desc->vsel_mask,
-				  sel);
+	ret = regmap_update_bits(rdev->regmap, reg,
+				 rdev->desc->vsel_mask,
+				 sel);
+	if (ret)
+		return ret;
+
+	if (rdev->desc->apply_bit)
+		ret = regmap_update_bits(rdev->regmap, rdev->desc->apply_reg,
+					 rdev->desc->apply_bit,
+					 rdev->desc->apply_bit);
+
+	return ret;
 }
 
 static int rk805_set_suspend_enable(struct regulator_dev *rdev)
Signature · 1 line
2.43.2
author
#8 lore raw

PATCH v3 5/5 regulator: rk808: Add RK816 support

In reply to Alex Bee

Add support for rk816 to the existing rk808 regulator driver.

The infrastructure of the driver can be re-used as is. A peculiarity for this version is, that BUCK1/BUCK2 have a (common) bit which needs to toggled after a voltage change to confirm the change. Regulator regmap takes care of that by defining a apply_bit and apply_reg for those regulators.

---
changes since v1:
- align regulator's .name and .of_match with updated binding

changes since v2:
- align regulator's .name and .of_match with updated binding (dropped "-regulator" prefix)

 drivers/regulator/rk808-regulator.c | 202 +++++++++++++++++++++++++++-
 1 file changed, 201 insertions(+), 1 deletion(-)
drivers/regulator/rk808-regulator.c +201 -1
index a6a563e402d0..14b60abd6afc 100644
@@ -158,6 +158,11 @@
 	RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg,	\
 	_vmask, _ereg, _emask, 0, 0, _etime, &rk808_reg_ops)
 
+#define RK816_DESC(_id, _match, _supply, _min, _max, _step, _vreg,	\
+	_vmask, _ereg, _emask, _disval, _etime)				\
+	RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg,	\
+	_vmask, _ereg, _emask, _emask, _disval, _etime, &rk816_reg_ops)
+
 #define RK817_DESC(_id, _match, _supply, _min, _max, _step, _vreg,	\
 	_vmask, _ereg, _emask, _disval, _etime)				\
 	RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg,	\
@@ -258,7 +263,7 @@ static const unsigned int rk808_buck1_2_ramp_table[] = {
 	2000, 4000, 6000, 10000
 };
 
-/* RK817 RK809 */
+/* RK817/RK809/RK816 (buck 1/2 only) */
 static const unsigned int rk817_buck1_4_ramp_table[] = {
 	3000, 6300, 12500, 25000
 };
@@ -640,6 +645,38 @@ static int rk808_set_suspend_disable(struct regulator_dev *rdev)
 				  rdev->desc->enable_mask);
 }
 
+static const struct rk8xx_register_bit rk816_suspend_bits[] = {
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 0),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 1),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 2),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 3),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 0),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 1),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 2),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 3),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 4),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 5),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 5),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 6),
+};
+
+static int rk816_set_suspend_enable(struct regulator_dev *rdev)
+{
+	int rid = rdev_get_id(rdev);
+
+	return regmap_update_bits(rdev->regmap, rk816_suspend_bits[rid].reg,
+				  rk816_suspend_bits[rid].bit,
+				  rk816_suspend_bits[rid].bit);
+}
+
+static int rk816_set_suspend_disable(struct regulator_dev *rdev)
+{
+	int rid = rdev_get_id(rdev);
+
+	return regmap_update_bits(rdev->regmap, rk816_suspend_bits[rid].reg,
+				  rk816_suspend_bits[rid].bit, 0);
+}
+
 static int rk817_set_suspend_enable_ctrl(struct regulator_dev *rdev,
 					 unsigned int en)
 {
@@ -913,6 +950,54 @@ static const struct regulator_ops rk809_buck5_ops_range = {
 	.set_suspend_disable	= rk817_set_suspend_disable,
 };
 
+static const struct regulator_ops rk816_buck1_2_ops_ranges = {
+	.list_voltage		= regulator_list_voltage_linear_range,
+	.map_voltage		= regulator_map_voltage_linear_range,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+	.set_voltage_time_sel	= regulator_set_voltage_time_sel,
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.is_enabled		= regulator_is_enabled_regmap,
+	.set_mode		= rk8xx_set_mode,
+	.get_mode		= rk8xx_get_mode,
+	.set_suspend_mode	= rk8xx_set_suspend_mode,
+	.set_ramp_delay		= regulator_set_ramp_delay_regmap,
+	.set_suspend_voltage	= rk808_set_suspend_voltage_range,
+	.set_suspend_enable	= rk816_set_suspend_enable,
+	.set_suspend_disable	= rk816_set_suspend_disable,
+};
+
+static const struct regulator_ops rk816_buck4_ops_ranges = {
+	.list_voltage		= regulator_list_voltage_linear_range,
+	.map_voltage		= regulator_map_voltage_linear_range,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+	.set_voltage_time_sel	= regulator_set_voltage_time_sel,
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.is_enabled		= regulator_is_enabled_regmap,
+	.set_mode		= rk8xx_set_mode,
+	.get_mode		= rk8xx_get_mode,
+	.set_suspend_mode	= rk8xx_set_suspend_mode,
+	.set_suspend_voltage	= rk808_set_suspend_voltage_range,
+	.set_suspend_enable	= rk816_set_suspend_enable,
+	.set_suspend_disable	= rk816_set_suspend_disable,
+};
+
+static const struct regulator_ops rk816_reg_ops = {
+	.list_voltage		= regulator_list_voltage_linear,
+	.map_voltage		= regulator_map_voltage_linear,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.is_enabled		= rk8xx_is_enabled_wmsk_regmap,
+	.set_suspend_voltage	= rk808_set_suspend_voltage,
+	.set_suspend_enable	= rk816_set_suspend_enable,
+	.set_suspend_disable	= rk816_set_suspend_disable,
+};
+
 static const struct regulator_ops rk817_reg_ops = {
 	.list_voltage		= regulator_list_voltage_linear,
 	.map_voltage		= regulator_map_voltage_linear,
@@ -1392,6 +1477,117 @@ static const struct regulator_desc rk809_reg[] = {
 			  DISABLE_VAL(3)),
 };
 
+static const struct linear_range rk816_buck_4_voltage_ranges[] = {
+	REGULATOR_LINEAR_RANGE(800000, 0, 26, 100000),
+	REGULATOR_LINEAR_RANGE(3500000, 27, 31, 0),
+};
+
+static const struct regulator_desc rk816_reg[] = {
+	{
+		.name = "dcdc1",
+		.supply_name = "vcc1",
+		.of_match = of_match_ptr("dcdc1"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = RK816_ID_DCDC1,
+		.ops = &rk816_buck1_2_ops_ranges,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = 64,
+		.linear_ranges = rk805_buck_1_2_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(rk805_buck_1_2_voltage_ranges),
+		.vsel_reg = RK818_BUCK1_ON_VSEL_REG,
+		.vsel_mask = RK818_BUCK_VSEL_MASK,
+		.apply_reg = RK816_DCDC_EN_REG2,
+		.apply_bit = RK816_BUCK_DVS_CONFIRM,
+		.enable_reg = RK816_DCDC_EN_REG1,
+		.enable_mask = BIT(4) | BIT(0),
+		.enable_val = BIT(4) | BIT(0),
+		.disable_val = BIT(4),
+		.ramp_reg = RK818_BUCK1_CONFIG_REG,
+		.ramp_mask = RK808_RAMP_RATE_MASK,
+		.ramp_delay_table = rk817_buck1_4_ramp_table,
+		.n_ramp_values = ARRAY_SIZE(rk817_buck1_4_ramp_table),
+		.of_map_mode = rk8xx_regulator_of_map_mode,
+		.owner = THIS_MODULE,
+	}, {
+		.name = "dcdc2",
+		.supply_name = "vcc2",
+		.of_match = of_match_ptr("dcdc2"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = RK816_ID_DCDC2,
+		.ops = &rk816_buck1_2_ops_ranges,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = 64,
+		.linear_ranges = rk805_buck_1_2_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(rk805_buck_1_2_voltage_ranges),
+		.vsel_reg = RK818_BUCK2_ON_VSEL_REG,
+		.vsel_mask = RK818_BUCK_VSEL_MASK,
+		.apply_reg = RK816_DCDC_EN_REG2,
+		.apply_bit = RK816_BUCK_DVS_CONFIRM,
+		.enable_reg = RK816_DCDC_EN_REG1,
+		.enable_mask = BIT(5) | BIT(1),
+		.enable_val = BIT(5) | BIT(1),
+		.disable_val = BIT(5),
+		.ramp_reg = RK818_BUCK2_CONFIG_REG,
+		.ramp_mask = RK808_RAMP_RATE_MASK,
+		.ramp_delay_table = rk817_buck1_4_ramp_table,
+		.n_ramp_values = ARRAY_SIZE(rk817_buck1_4_ramp_table),
+		.of_map_mode = rk8xx_regulator_of_map_mode,
+		.owner = THIS_MODULE,
+	}, {
+		.name = "dcdc3",
+		.supply_name = "vcc3",
+		.of_match = of_match_ptr("dcdc3"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = RK816_ID_DCDC3,
+		.ops = &rk808_switch_ops,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = 1,
+		.enable_reg = RK816_DCDC_EN_REG1,
+		.enable_mask = BIT(6) | BIT(2),
+		.enable_val =  BIT(6) | BIT(2),
+		.disable_val = BIT(6),
+		.of_map_mode = rk8xx_regulator_of_map_mode,
+		.owner = THIS_MODULE,
+	}, {
+		.name = "dcdc4",
+		.supply_name = "vcc4",
+		.of_match = of_match_ptr("dcdc4"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = RK816_ID_DCDC4,
+		.ops = &rk816_buck4_ops_ranges,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = 32,
+		.linear_ranges = rk816_buck_4_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(rk816_buck_4_voltage_ranges),
+		.vsel_reg = RK818_BUCK4_ON_VSEL_REG,
+		.vsel_mask = RK818_BUCK4_VSEL_MASK,
+		.enable_reg = RK816_DCDC_EN_REG1,
+		.enable_mask = BIT(7) | BIT(3),
+		.enable_val = BIT(7) | BIT(3),
+		.disable_val = BIT(7),
+		.of_map_mode = rk8xx_regulator_of_map_mode,
+		.owner = THIS_MODULE,
+	},
+	RK816_DESC(RK816_ID_LDO1, "ldo1", "vcc5", 800, 3400, 100,
+		   RK818_LDO1_ON_VSEL_REG, RK818_LDO_VSEL_MASK,
+		   RK816_LDO_EN_REG1, ENABLE_MASK(0), DISABLE_VAL(0), 400),
+	RK816_DESC(RK816_ID_LDO2, "ldo2", "vcc5", 800, 3400, 100,
+		   RK818_LDO2_ON_VSEL_REG, RK818_LDO_VSEL_MASK,
+		   RK816_LDO_EN_REG1, ENABLE_MASK(1), DISABLE_VAL(1), 400),
+	RK816_DESC(RK816_ID_LDO3, "ldo3", "vcc5", 800, 3400, 100,
+		   RK818_LDO3_ON_VSEL_REG, RK818_LDO_VSEL_MASK,
+		   RK816_LDO_EN_REG1, ENABLE_MASK(2), DISABLE_VAL(2), 400),
+	RK816_DESC(RK816_ID_LDO4, "ldo4", "vcc6", 800, 3400, 100,
+		   RK818_LDO4_ON_VSEL_REG, RK818_LDO_VSEL_MASK,
+		   RK816_LDO_EN_REG1, ENABLE_MASK(3), DISABLE_VAL(3), 400),
+	RK816_DESC(RK816_ID_LDO5, "ldo5", "vcc6", 800, 3400, 100,
+		   RK818_LDO5_ON_VSEL_REG, RK818_LDO_VSEL_MASK,
+		   RK816_LDO_EN_REG2, ENABLE_MASK(0), DISABLE_VAL(0), 400),
+	RK816_DESC(RK816_ID_LDO6, "ldo6", "vcc6", 800, 3400, 100,
+		   RK818_LDO6_ON_VSEL_REG, RK818_LDO_VSEL_MASK,
+		   RK816_LDO_EN_REG2, ENABLE_MASK(1), DISABLE_VAL(1), 400),
+};
+
 static const struct regulator_desc rk817_reg[] = {
 	{
 		.name = "DCDC_REG1",
@@ -1714,6 +1910,10 @@ static int rk808_regulator_probe(struct platform_device *pdev)
 		regulators = rk809_reg;
 		nregulators = RK809_NUM_REGULATORS;
 		break;
+	case RK816_ID:
+		regulators = rk816_reg;
+		nregulators = ARRAY_SIZE(rk816_reg);
+		break;
 	case RK817_ID:
 		regulators = rk817_reg;
 		nregulators = RK817_NUM_REGULATORS;
Signature · 1 line
2.43.2