Skip to contentSkip to conversation

rtl8226b/8221b add C45 instances and SerDes switching

PATCH Superseded Eric Woudstra 3 participants 14 messages Apr 2, 2024

Subsystems (4)

v3 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

v3 cover rtl8226b/8221b add C45 instances and SerDes switching

Based on the comments in [PATCH net-next]
"Realtek RTL822x PHY rework to c45 and SerDes interface switching"

Adds SerDes switching interface between 2500base-x and sgmii for rtl8221b and rtl8226b.

Add get_rate_matching() for rtl8226b and rtl8221b, reading the serdes mode from phy.

Driver instances are added for rtl8226b and rtl8221b for Clause 45 access only. The existing code is not touched, they use newly added functions. They also use the same rtl822xb_config_init() and rtl822xb_get_rate_matching() as these functions also can be used for direct Clause 45 access. Also Adds definition of MMC 31 registers, which cannot be used through C45-over-C22, only when phydev->is_c45 is set.

Change rtlgen_get_speed() so the register value is passed as argument. Using Clause 45 access, this value is retrieved differently. Rename it to rtlgen_decode_speed() and add a call to it in rtl822x_c45_read_status().

Add rtl822x_c45_get_features() to set supported ports for rtl8221b.

Then 1 quirk is added for sfp modules known to have a rtl8221b behind RollBall, Clause 45 only, protocol.

Changed in PATCH v3:
* Only apply to rtl8221b and rtl8226b phy's
* Set phydev->rate_matching in .config_init()
* Removed OEM SFP fixup for now, as there are modules with the same vendor name/PN, but with different PHY's. We found rtl8221b, but also the ty8821, which is not supported.

Changed in PATCH v2:

* Set author to Marek for the commit of the new C45 instances
* Separate commit for setting supported ports
* Renamed rtlgen_get_speed to rtlgen_decode_speed
* Always fill in possible interfaces
* Renamed sfp_fixup_oem_2_5g to sfp_fixup_oem_2_5gbaset
* Only update phydev->interface when link is up

Alexander Couzens (1):
net: phy: realtek: configure SerDes mode for rtl822xb PHYs

Eric Woudstra (3):
net: phy: realtek: add get_rate_matching() for rtl822xb PHYs
net: phy: realtek: Change rtlgen_get_speed() to rtlgen_decode_speed()
net: phy: realtek: add rtl822x_c45_get_features() to set supported
ports

Marek Behún (2):
net: phy: realtek: Add driver instances for rtl8221b via Clause 45
net: sfp: add quirk for another multigig RollBall transceiver

 drivers/net/phy/realtek.c | 327 +++++++++++++++++++++++++++++++++++---
 drivers/net/phy/sfp.c     |   1 +
 2 files changed, 302 insertions(+), 26 deletions(-)
Signature · 1 line
2.42.1
#1 lore raw

PATCH v3 1/6 net: phy: realtek: configure SerDes mode for rtl822xb PHYs

From: Alexander Couzens <[email protected]>

The rtl8221b and rtl8226b series support switching SerDes mode between 2500base-x and sgmii based on the negotiated copper speed.

Configure this switching mode according to SerDes modes supported by host.

There is an additional datasheet for RTL8226B/RTL8221B called "SERDES MODE SETTING FLOW APPLICATION NOTE" where a sequence is described to setup interface and rate adapter mode.

However, there is no documentation about the meaning of registers and bits, it's literally just magic numbers and pseudo-code.

[ refactored, dropped HiSGMII mode and changed commit message ]
[ changed rtl822x_update_interface() to use vendor register ]
[ always fill in possible interfaces ]
[ only apply to rtl8221b and rtl8226b phy's ]
[ set phydev->rate_matching in .config_init() ]
---
 drivers/net/phy/realtek.c | 114 ++++++++++++++++++++++++++++++++++++--
 1 file changed, 110 insertions(+), 4 deletions(-)
drivers/net/phy/realtek.c +110 -4
index 1fa70427b2a2..70cd1834a832 100644
@@ -54,6 +54,16 @@
 						 RTL8201F_ISR_LINK)
 #define RTL8201F_IER				0x13
 
+#define RTL822X_VND1_SERDES_OPTION			0x697a
+#define RTL822X_VND1_SERDES_OPTION_MODE_MASK		GENMASK(5, 0)
+#define RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX_SGMII		0
+#define RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX		2
+
+#define RTL822X_VND1_SERDES_CTRL3			0x7580
+#define RTL822X_VND1_SERDES_CTRL3_MODE_MASK		GENMASK(5, 0)
+#define RTL822X_VND1_SERDES_CTRL3_MODE_SGMII			0x02
+#define RTL822X_VND1_SERDES_CTRL3_MODE_2500BASEX		0x16
+
 #define RTL8366RB_POWER_SAVE			0x15
 #define RTL8366RB_POWER_SAVE_ON			BIT(12)
 
@@ -659,6 +669,63 @@ static int rtl822x_write_mmd(struct phy_device *phydev, int devnum, u16 regnum,
 	return ret;
 }
 
+static int rtl822xb_config_init(struct phy_device *phydev)
+{
+	bool has_2500, has_sgmii;
+	u16 mode;
+	int ret;
+
+	has_2500 = test_bit(PHY_INTERFACE_MODE_2500BASEX,
+			    phydev->host_interfaces) ||
+		   phydev->interface == PHY_INTERFACE_MODE_2500BASEX;
+
+	has_sgmii = test_bit(PHY_INTERFACE_MODE_SGMII,
+			     phydev->host_interfaces) ||
+		    phydev->interface == PHY_INTERFACE_MODE_SGMII;
+
+	/* fill in possible interfaces */
+	__assign_bit(PHY_INTERFACE_MODE_2500BASEX, phydev->possible_interfaces,
+		     has_2500);
+	__assign_bit(PHY_INTERFACE_MODE_SGMII, phydev->possible_interfaces,
+		     has_sgmii);
+
+	if (!has_2500 && !has_sgmii)
+		return 0;
+
+	/* determine SerDes option mode */
+	if (has_2500 && !has_sgmii) {
+		mode = RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX;
+		phydev->rate_matching = RATE_MATCH_PAUSE;
+	} else {
+		mode = RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX_SGMII;
+		phydev->rate_matching = RATE_MATCH_NONE;
+	}
+
+	/* the following sequence with magic numbers sets up the SerDes
+	 * option mode
+	 */
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x75f3, 0);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_modify_mmd_changed(phydev, MDIO_MMD_VEND1,
+				     RTL822X_VND1_SERDES_OPTION,
+				     RTL822X_VND1_SERDES_OPTION_MODE_MASK,
+				     mode);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x6a04, 0x0503);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x6f10, 0xd455);
+	if (ret < 0)
+		return ret;
+
+	return phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x6f11, 0x8020);
+}
+
 static int rtl822x_get_features(struct phy_device *phydev)
 {
 	int val;
@@ -695,6 +762,28 @@ static int rtl822x_config_aneg(struct phy_device *phydev)
 	return __genphy_config_aneg(phydev, ret);
 }
 
+static void rtl822xb_update_interface(struct phy_device *phydev)
+{
+	int val;
+
+	if (!phydev->link)
+		return;
+
+	/* Change interface according to serdes mode */
+	val = phy_read_mmd(phydev, MDIO_MMD_VEND1, RTL822X_VND1_SERDES_CTRL3);
+	if (val < 0)
+		return;
+
+	switch (val & RTL822X_VND1_SERDES_CTRL3_MODE_MASK) {
+	case RTL822X_VND1_SERDES_CTRL3_MODE_2500BASEX:
+		phydev->interface = PHY_INTERFACE_MODE_2500BASEX;
+		break;
+	case RTL822X_VND1_SERDES_CTRL3_MODE_SGMII:
+		phydev->interface = PHY_INTERFACE_MODE_SGMII;
+		break;
+	}
+}
+
 static int rtl822x_read_status(struct phy_device *phydev)
 {
 	int ret;
@@ -716,6 +805,19 @@ static int rtl822x_read_status(struct phy_device *phydev)
 	return rtlgen_get_speed(phydev);
 }
 
+static int rtl822xb_read_status(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = rtl822x_read_status(phydev);
+	if (ret < 0)
+		return ret;
+
+	rtl822xb_update_interface(phydev);
+
+	return 0;
+}
+
 static bool rtlgen_supports_2_5gbps(struct phy_device *phydev)
 {
 	int val;
@@ -988,7 +1090,8 @@ static struct phy_driver realtek_drvs[] = {
 		.name		= "RTL8226B_RTL8221B 2.5Gbps PHY",
 		.get_features	= rtl822x_get_features,
 		.config_aneg	= rtl822x_config_aneg,
-		.read_status	= rtl822x_read_status,
+		.config_init    = rtl822xb_config_init,
+		.read_status	= rtl822xb_read_status,
 		.suspend	= genphy_suspend,
 		.resume		= rtlgen_resume,
 		.read_page	= rtl821x_read_page,
@@ -1010,7 +1113,8 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8226B-CG_RTL8221B-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
-		.read_status    = rtl822x_read_status,
+		.config_init    = rtl822xb_config_init,
+		.read_status    = rtl822xb_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
 		.read_page      = rtl821x_read_page,
@@ -1020,7 +1124,8 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8221B-VB-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
-		.read_status    = rtl822x_read_status,
+		.config_init    = rtl822xb_config_init,
+		.read_status    = rtl822xb_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
 		.read_page      = rtl821x_read_page,
@@ -1030,7 +1135,8 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8221B-VM-CG 2.5Gbps PHY",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
-		.read_status    = rtl822x_read_status,
+		.config_init    = rtl822xb_config_init,
+		.read_status    = rtl822xb_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
 		.read_page      = rtl821x_read_page,
Signature · 1 line
2.42.1
maintainer Reviewed-by on v3 1/6
#2 lore raw

Re: [PATCH v3 net-next 1/6] net: phy: realtek: configure SerDes mode for rtl822xb PHYs

Quoted 15 lines · Eric Woudstra

From: Alexander Couzens <[email protected]>

The rtl8221b and rtl8226b series support switching SerDes mode between 2500base-x and sgmii based on the negotiated copper speed.

Configure this switching mode according to SerDes modes supported by host.

There is an additional datasheet for RTL8226B/RTL8221B called "SERDES MODE SETTING FLOW APPLICATION NOTE" where a sequence is described to setup interface and rate adapter mode.

However, there is no documentation about the meaning of registers and bits, it's literally just magic numbers and pseudo-code.

Quoted 8 lines
[ refactored, dropped HiSGMII mode and changed commit message ]
[ changed rtl822x_update_interface() to use vendor register ]
[ always fill in possible interfaces ]
[ only apply to rtl8221b and rtl8226b phy's ]
[ set phydev->rate_matching in .config_init() ]

Thanks!

Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
#3 lore raw

PATCH v3 2/6 net: phy: realtek: add get_rate_matching() for rtl822xb PHYs

In reply to Eric Woudstra

Uses vendor register to determine if SerDes is setup in rate-matching mode.

Rate-matching only supported when SerDes is set to 2500base-x.

---
 drivers/net/phy/realtek.c | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)
drivers/net/phy/realtek.c +26 -0
index 70cd1834a832..ca1d61fa44f5 100644
@@ -726,6 +726,28 @@ static int rtl822xb_config_init(struct phy_device *phydev)
 	return phy_write_mmd(phydev, MDIO_MMD_VEND1, 0x6f11, 0x8020);
 }
 
+static int rtl822xb_get_rate_matching(struct phy_device *phydev,
+				      phy_interface_t iface)
+{
+	int val;
+
+	/* Only rate matching at 2500base-x */
+	if (iface != PHY_INTERFACE_MODE_2500BASEX)
+		return RATE_MATCH_NONE;
+
+	val = phy_read_mmd(phydev, MDIO_MMD_VEND1, RTL822X_VND1_SERDES_OPTION);
+	if (val < 0)
+		return val;
+
+	switch (val & RTL822X_VND1_SERDES_OPTION_MODE_MASK) {
+	case RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX:
+		return RATE_MATCH_PAUSE;
+	/* case RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX_SGMII: */
+	default:
+		return RATE_MATCH_NONE;
+	}
+}
+
 static int rtl822x_get_features(struct phy_device *phydev)
 {
 	int val;
@@ -1091,6 +1113,7 @@ static struct phy_driver realtek_drvs[] = {
 		.get_features	= rtl822x_get_features,
 		.config_aneg	= rtl822x_config_aneg,
 		.config_init    = rtl822xb_config_init,
+		.get_rate_matching = rtl822xb_get_rate_matching,
 		.read_status	= rtl822xb_read_status,
 		.suspend	= genphy_suspend,
 		.resume		= rtlgen_resume,
@@ -1114,6 +1137,7 @@ static struct phy_driver realtek_drvs[] = {
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
 		.config_init    = rtl822xb_config_init,
+		.get_rate_matching = rtl822xb_get_rate_matching,
 		.read_status    = rtl822xb_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
@@ -1125,6 +1149,7 @@ static struct phy_driver realtek_drvs[] = {
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
 		.config_init    = rtl822xb_config_init,
+		.get_rate_matching = rtl822xb_get_rate_matching,
 		.read_status    = rtl822xb_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
@@ -1136,6 +1161,7 @@ static struct phy_driver realtek_drvs[] = {
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
 		.config_init    = rtl822xb_config_init,
+		.get_rate_matching = rtl822xb_get_rate_matching,
 		.read_status    = rtl822xb_read_status,
 		.suspend        = genphy_suspend,
 		.resume         = rtlgen_resume,
Signature · 1 line
2.42.1
maintainer Reviewed-by on v3 2/6
#4 lore raw

Re: [PATCH v3 net-next 2/6] net: phy: realtek: add get_rate_matching() for rtl822xb PHYs

drivers/net/phy/realtek.c static int rtl822xb_config_init(struct phy_device *phydev) · line 748

Quoted 7 lines · Eric Woudstra
drivers/net/phy/realtek.c +7 -0
+	switch (val & RTL822X_VND1_SERDES_OPTION_MODE_MASK) {
+	case RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX:
+		return RATE_MATCH_PAUSE;
+	/* case RTL822X_VND1_SERDES_OPTION_MODE_2500BASEX_SGMII: */
+	default:
+		return RATE_MATCH_NONE;
+	}

Nit: Is this actually useful to have as a switch statement?

In any case,

Thanks!

Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
#5 lore raw

PATCH v3 3/6 net: phy: realtek: Add driver instances for rtl8221b via Clause 45

In reply to Eric Woudstra

From: Marek Behún <[email protected]>

Collected from several commits in [PATCH net-next] "Realtek RTL822x PHY rework to c45 and SerDes interface switching"

The instances are used by Clause 45 only accessible PHY's on several sfp modules, which are using RollBall protocol.

[ Added matching functions to differentiate C45 instances ]
---
 drivers/net/phy/realtek.c | 135 ++++++++++++++++++++++++++++++++++++--
 1 file changed, 131 insertions(+), 4 deletions(-)
drivers/net/phy/realtek.c +131 -4
index ca1d61fa44f5..2215a31d5aab 100644
@@ -64,6 +64,13 @@
 #define RTL822X_VND1_SERDES_CTRL3_MODE_SGMII			0x02
 #define RTL822X_VND1_SERDES_CTRL3_MODE_2500BASEX		0x16
 
+/* RTL822X_VND2_XXXXX registers are only accessible when phydev->is_c45
+ * is set, they cannot be accessed by C45-over-C22.
+ */
+#define RTL822X_VND2_GBCR				0xa412
+
+#define RTL822X_VND2_GANLPAR				0xa414
+
 #define RTL8366RB_POWER_SAVE			0x15
 #define RTL8366RB_POWER_SAVE_ON			BIT(12)
 
@@ -74,6 +81,9 @@
 
 #define RTL_GENERIC_PHYID			0x001cc800
 #define RTL_8211FVD_PHYID			0x001cc878
+#define RTL_8221B_VB_CG				0x001cc849
+#define RTL_8221B_VN_CG				0x001cc84a
+#define RTL_8251B				0x001cc862
 
 MODULE_DESCRIPTION("Realtek PHY driver");
 MODULE_AUTHOR("Johnson Leung");
@@ -840,6 +850,67 @@ static int rtl822xb_read_status(struct phy_device *phydev)
 	return 0;
 }
 
+static int rtl822x_c45_config_aneg(struct phy_device *phydev)
+{
+	bool changed = false;
+	int ret, val;
+
+	if (phydev->autoneg == AUTONEG_DISABLE)
+		return genphy_c45_pma_setup_forced(phydev);
+
+	ret = genphy_c45_an_config_aneg(phydev);
+	if (ret < 0)
+		return ret;
+	if (ret > 0)
+		changed = true;
+
+	val = linkmode_adv_to_mii_ctrl1000_t(phydev->advertising);
+
+	/* Vendor register as C45 has no standardized support for 1000BaseT */
+	ret = phy_modify_mmd_changed(phydev, MDIO_MMD_VEND2, RTL822X_VND2_GBCR,
+				     ADVERTISE_1000FULL, val);
+	if (ret < 0)
+		return ret;
+	if (ret > 0)
+		changed = true;
+
+	return genphy_c45_check_and_restart_aneg(phydev, changed);
+}
+
+static int rtl822x_c45_read_status(struct phy_device *phydev)
+{
+	int ret, val;
+
+	ret = genphy_c45_read_status(phydev);
+	if (ret < 0)
+		return ret;
+
+	/* Vendor register as C45 has no standardized support for 1000BaseT */
+	if (phydev->autoneg == AUTONEG_ENABLE) {
+		val = phy_read_mmd(phydev, MDIO_MMD_VEND2,
+				   RTL822X_VND2_GANLPAR);
+		if (val < 0)
+			return val;
+
+		mii_stat1000_mod_linkmode_lpa_t(phydev->lp_advertising, val);
+	}
+
+	return 0;
+}
+
+static int rtl822xb_c45_read_status(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = rtl822x_c45_read_status(phydev);
+	if (ret < 0)
+		return ret;
+
+	rtl822xb_update_interface(phydev);
+
+	return 0;
+}
+
 static bool rtlgen_supports_2_5gbps(struct phy_device *phydev)
 {
 	int val;
@@ -863,6 +934,35 @@ static int rtl8226_match_phy_device(struct phy_device *phydev)
 	       rtlgen_supports_2_5gbps(phydev);
 }
 
+static int rtlgen_is_c45_match(struct phy_device *phydev, unsigned int id,
+			       bool is_c45)
+{
+	if (phydev->is_c45)
+		return is_c45 && (id == phydev->c45_ids.device_ids[1]);
+	else
+		return !is_c45 && (id == phydev->phy_id);
+}
+
+static int rtl8221b_vb_cg_c22_match_phy_device(struct phy_device *phydev)
+{
+	return rtlgen_is_c45_match(phydev, RTL_8221B_VB_CG, false);
+}
+
+static int rtl8221b_vb_cg_c45_match_phy_device(struct phy_device *phydev)
+{
+	return rtlgen_is_c45_match(phydev, RTL_8221B_VB_CG, true);
+}
+
+static int rtl8221b_vn_cg_c22_match_phy_device(struct phy_device *phydev)
+{
+	return rtlgen_is_c45_match(phydev, RTL_8221B_VN_CG, false);
+}
+
+static int rtl8221b_vn_cg_c45_match_phy_device(struct phy_device *phydev)
+{
+	return rtlgen_is_c45_match(phydev, RTL_8221B_VN_CG, true);
+}
+
 static int rtlgen_resume(struct phy_device *phydev)
 {
 	int ret = genphy_resume(phydev);
@@ -873,6 +973,15 @@ static int rtlgen_resume(struct phy_device *phydev)
 	return ret;
 }
 
+static int rtlgen_c45_resume(struct phy_device *phydev)
+{
+	int ret = genphy_c45_pma_resume(phydev);
+
+	msleep(20);
+
+	return ret;
+}
+
 static int rtl9000a_config_init(struct phy_device *phydev)
 {
 	phydev->autoneg = AUTONEG_DISABLE;
@@ -1144,8 +1253,8 @@ static struct phy_driver realtek_drvs[] = {
 		.read_page      = rtl821x_read_page,
 		.write_page     = rtl821x_write_page,
 	}, {
-		PHY_ID_MATCH_EXACT(0x001cc849),
-		.name           = "RTL8221B-VB-CG 2.5Gbps PHY",
+		.match_phy_device = rtl8221b_vb_cg_c22_match_phy_device,
+		.name           = "RTL8221B-VB-CG 2.5Gbps PHY (C22)",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
 		.config_init    = rtl822xb_config_init,
@@ -1156,8 +1265,17 @@ static struct phy_driver realtek_drvs[] = {
 		.read_page      = rtl821x_read_page,
 		.write_page     = rtl821x_write_page,
 	}, {
-		PHY_ID_MATCH_EXACT(0x001cc84a),
-		.name           = "RTL8221B-VM-CG 2.5Gbps PHY",
+		.match_phy_device = rtl8221b_vb_cg_c45_match_phy_device,
+		.name           = "RTL8221B-VB-CG 2.5Gbps PHY (C45)",
+		.config_init    = rtl822xb_config_init,
+		.get_rate_matching = rtl822xb_get_rate_matching,
+		.config_aneg    = rtl822x_c45_config_aneg,
+		.read_status    = rtl822xb_c45_read_status,
+		.suspend        = genphy_c45_pma_suspend,
+		.resume         = rtlgen_c45_resume,
+	}, {
+		.match_phy_device = rtl8221b_vn_cg_c22_match_phy_device,
+		.name           = "RTL8221B-VM-CG 2.5Gbps PHY (C22)",
 		.get_features   = rtl822x_get_features,
 		.config_aneg    = rtl822x_config_aneg,
 		.config_init    = rtl822xb_config_init,
@@ -1167,6 +1285,15 @@ static struct phy_driver realtek_drvs[] = {
 		.resume         = rtlgen_resume,
 		.read_page      = rtl821x_read_page,
 		.write_page     = rtl821x_write_page,
+	}, {
+		.match_phy_device = rtl8221b_vn_cg_c45_match_phy_device,
+		.name           = "RTL8221B-VN-CG 2.5Gbps PHY (C45)",
+		.config_init    = rtl822xb_config_init,
+		.get_rate_matching = rtl822xb_get_rate_matching,
+		.config_aneg    = rtl822x_c45_config_aneg,
+		.read_status    = rtl822xb_c45_read_status,
+		.suspend        = genphy_c45_pma_suspend,
+		.resume         = rtlgen_c45_resume,
 	}, {
 		PHY_ID_MATCH_EXACT(0x001cc862),
 		.name           = "RTL8251B 5Gbps PHY",
Signature · 1 line
2.42.1
maintainer Reviewed-by on v3 3/6
#6 lore raw

Re: [PATCH v3 net-next 3/6] net: phy: realtek: Add driver instances for rtl8221b via Clause 45

Quoted 11 lines · Eric Woudstra

From: Marek Behún <[email protected]>

Collected from several commits in [PATCH net-next] "Realtek RTL822x PHY rework to c45 and SerDes interface switching"

The instances are used by Clause 45 only accessible PHY's on several sfp modules, which are using RollBall protocol.

[ Added matching functions to differentiate C45 instances ]

Thanks!

Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
#7 lore raw

PATCH v3 4/6 net: phy: realtek: Change rtlgen_get_speed() to rtlgen_decode_speed()

In reply to Eric Woudstra

The value of the register to determine the speed, is retrieved differently when using Clause 45 only. To use the rtlgen_get_speed() function in this case, pass the value of the register as argument to rtlgen_get_speed(). The function would then always return 0, so change it to void. A better name for this function now is rtlgen_decode_speed().

Replace a call to genphy_read_status() followed by rtlgen_get_speed() with a call to rtlgen_read_status() in rtl822x_read_status().

Add reading speed to rtl822x_c45_read_status().

---
 drivers/net/phy/realtek.c | 46 +++++++++++++++++++++------------------
 1 file changed, 25 insertions(+), 21 deletions(-)
drivers/net/phy/realtek.c +25 -21
index 2215a31d5aab..af5e77fd6576 100644
@@ -71,6 +71,8 @@
 
 #define RTL822X_VND2_GANLPAR				0xa414
 
+#define RTL822X_VND2_PHYSR				0xa434
+
 #define RTL8366RB_POWER_SAVE			0x15
 #define RTL8366RB_POWER_SAVE_ON			BIT(12)
 
@@ -551,17 +553,8 @@ static int rtl8366rb_config_init(struct phy_device *phydev)
 }
 
 /* get actual speed to cover the downshift case */
-static int rtlgen_get_speed(struct phy_device *phydev)
+static void rtlgen_decode_speed(struct phy_device *phydev, int val)
 {
-	int val;
-
-	if (!phydev->link)
-		return 0;
-
-	val = phy_read_paged(phydev, 0xa43, 0x12);
-	if (val < 0)
-		return val;
-
 	switch (val & RTLGEN_SPEED_MASK) {
 	case 0x0000:
 		phydev->speed = SPEED_10;
@@ -584,19 +577,26 @@ static int rtlgen_get_speed(struct phy_device *phydev)
 	default:
 		break;
 	}
-
-	return 0;
 }
 
 static int rtlgen_read_status(struct phy_device *phydev)
 {
-	int ret;
+	int ret, val;
 
 	ret = genphy_read_status(phydev);
 	if (ret < 0)
 		return ret;
 
-	return rtlgen_get_speed(phydev);
+	if (!phydev->link)
+		return 0;
+
+	val = phy_read_paged(phydev, 0xa43, 0x12);
+	if (val < 0)
+		return val;
+
+	rtlgen_decode_speed(phydev, val);
+
+	return 0;
 }
 
 static int rtlgen_read_mmd(struct phy_device *phydev, int devnum, u16 regnum)
@@ -818,8 +818,6 @@ static void rtl822xb_update_interface(struct phy_device *phydev)
 
 static int rtl822x_read_status(struct phy_device *phydev)
 {
-	int ret;
-
 	if (phydev->autoneg == AUTONEG_ENABLE) {
 		int lpadv = phy_read_paged(phydev, 0xa5d, 0x13);
 
@@ -830,11 +828,7 @@ static int rtl822x_read_status(struct phy_device *phydev)
 						  lpadv);
 	}
 
-	ret = genphy_read_status(phydev);
-	if (ret < 0)
-		return ret;
-
-	return rtlgen_get_speed(phydev);
+	return rtlgen_read_status(phydev);
 }
 
 static int rtl822xb_read_status(struct phy_device *phydev)
@@ -895,6 +889,16 @@ static int rtl822x_c45_read_status(struct phy_device *phydev)
 		mii_stat1000_mod_linkmode_lpa_t(phydev->lp_advertising, val);
 	}
 
+	if (!phydev->link)
+		return 0;
+
+	/* Read actual speed from vendor register. */
+	val = phy_read_mmd(phydev, MDIO_MMD_VEND2, RTL822X_VND2_PHYSR);
+	if (val < 0)
+		return val;
+
+	rtlgen_decode_speed(phydev, val);
+
 	return 0;
 }
 
Signature · 1 line
2.42.1
maintainer Reviewed-by on v3 4/6
#8 lore raw

Re: [PATCH v3 net-next 4/6] net: phy: realtek: Change rtlgen_get_speed() to rtlgen_decode_speed()

Quoted 6 lines · Eric Woudstra

The value of the register to determine the speed, is retrieved differently when using Clause 45 only. To use the rtlgen_get_speed() function in this case, pass the value of the register as argument to rtlgen_get_speed(). The function would then always return 0, so change it to void. A better name for this function now is rtlgen_decode_speed().

Quoted 6 lines

Replace a call to genphy_read_status() followed by rtlgen_get_speed() with a call to rtlgen_read_status() in rtl822x_read_status().

Add reading speed to rtl822x_c45_read_status().

Thanks!

Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!
#9 lore raw

PATCH v3 5/6 net: phy: realtek: add rtl822x_c45_get_features() to set supported ports

In reply to Eric Woudstra

Sets ETHTOOL_LINK_MODE_TP_BIT and ETHTOOL_LINK_MODE_MII_BIT in phydev->supported.

---
 drivers/net/phy/realtek.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)
drivers/net/phy/realtek.c +12 -0
index af5e77fd6576..b483aa3800e2 100644
@@ -844,6 +844,16 @@ static int rtl822xb_read_status(struct phy_device *phydev)
 	return 0;
 }
 
+static int rtl822x_c45_get_features(struct phy_device *phydev)
+{
+	linkmode_set_bit(ETHTOOL_LINK_MODE_TP_BIT,
+			 phydev->supported);
+	linkmode_set_bit(ETHTOOL_LINK_MODE_MII_BIT,
+			 phydev->supported);
+
+	return genphy_c45_pma_read_abilities(phydev);
+}
+
 static int rtl822x_c45_config_aneg(struct phy_device *phydev)
 {
 	bool changed = false;
@@ -1273,6 +1283,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8221B-VB-CG 2.5Gbps PHY (C45)",
 		.config_init    = rtl822xb_config_init,
 		.get_rate_matching = rtl822xb_get_rate_matching,
+		.get_features   = rtl822x_c45_get_features,
 		.config_aneg    = rtl822x_c45_config_aneg,
 		.read_status    = rtl822xb_c45_read_status,
 		.suspend        = genphy_c45_pma_suspend,
@@ -1294,6 +1305,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8221B-VN-CG 2.5Gbps PHY (C45)",
 		.config_init    = rtl822xb_config_init,
 		.get_rate_matching = rtl822xb_get_rate_matching,
+		.get_features   = rtl822x_c45_get_features,
 		.config_aneg    = rtl822x_c45_config_aneg,
 		.read_status    = rtl822xb_c45_read_status,
 		.suspend        = genphy_c45_pma_suspend,
Signature · 1 line
2.42.1
#10 lore raw

Re: [PATCH v3 net-next 5/6] net: phy: realtek: add rtl822x_c45_get_features() to set supported ports

Quoted 2 lines · Eric Woudstra

Sets ETHTOOL_LINK_MODE_TP_BIT and ETHTOOL_LINK_MODE_MII_BIT in phydev->supported.

Why ETHTOOL_LINK_MODE_MII_BIT? None of those phys got MII as external interface. Or am I getting something wrong here?

Quoted 46 lines
---
 drivers/net/phy/realtek.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)
drivers/net/phy/realtek.c +12 -0
index af5e77fd6576..b483aa3800e2 100644
@@ -844,6 +844,16 @@ static int rtl822xb_read_status(struct phy_device *phydev)
 	return 0;
 }
 
+static int rtl822x_c45_get_features(struct phy_device *phydev)
+{
+	linkmode_set_bit(ETHTOOL_LINK_MODE_TP_BIT,
+			 phydev->supported);
+	linkmode_set_bit(ETHTOOL_LINK_MODE_MII_BIT,
+			 phydev->supported);
+
+	return genphy_c45_pma_read_abilities(phydev);
+}
+
 static int rtl822x_c45_config_aneg(struct phy_device *phydev)
 {
 	bool changed = false;
@@ -1273,6 +1283,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8221B-VB-CG 2.5Gbps PHY (C45)",
 		.config_init    = rtl822xb_config_init,
 		.get_rate_matching = rtl822xb_get_rate_matching,
+		.get_features   = rtl822x_c45_get_features,
 		.config_aneg    = rtl822x_c45_config_aneg,
 		.read_status    = rtl822xb_c45_read_status,
 		.suspend        = genphy_c45_pma_suspend,
@@ -1294,6 +1305,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name           = "RTL8221B-VN-CG 2.5Gbps PHY (C45)",
 		.config_init    = rtl822xb_config_init,
 		.get_rate_matching = rtl822xb_get_rate_matching,
+		.get_features   = rtl822x_c45_get_features,
 		.config_aneg    = rtl822x_c45_config_aneg,
 		.read_status    = rtl822xb_c45_read_status,
 		.suspend        = genphy_c45_pma_suspend,
Signature · 1 line
2.42.1
#11 lore raw

Re: [PATCH v3 net-next 5/6] net: phy: realtek: add rtl822x_c45_get_features() to set supported ports

Quoted 7 lines · Daniel Golle
Quoted 2 lines · Eric Woudstra

Sets ETHTOOL_LINK_MODE_TP_BIT and ETHTOOL_LINK_MODE_MII_BIT in phydev->supported.

Why ETHTOOL_LINK_MODE_MII_BIT? None of those phys got MII as external interface. Or am I getting something wrong here?

I have copied it from my rtl8153:

# ethtool enu1u1
Settings for enu1u1:
	Supported ports: [ TP	 MII ]

But I see on rtl8125 it is indeed only TP, so it looks like I chose the wrong example. I'll remove MII then if, this should not be there.

The thing is, if no ports are set here, then from ethtool it looks like all ports are supported.

#12 lore raw

PATCH v3 6/6 net: sfp: add quirk for another multigig RollBall transceiver

In reply to Eric Woudstra

From: Marek Behún <[email protected]>

Add quirk for another RollBall copper transceiver: Turris RTSFP-2.5G, containing 2.5g capable RTL8221B PHY.

---
 drivers/net/phy/sfp.c | 1 +
 1 file changed, 1 insertion(+)
drivers/net/phy/sfp.c +1 -0
index f75c9eb3958e..6e7639fc64dd 100644
@@ -506,6 +506,7 @@ static const struct sfp_quirk sfp_quirks[] = {
 	SFP_QUIRK_M("OEM", "SFP-2.5G-T", sfp_quirk_oem_2_5g),
 	SFP_QUIRK_F("OEM", "RTSFP-10", sfp_fixup_rollball_cc),
 	SFP_QUIRK_F("OEM", "RTSFP-10G", sfp_fixup_rollball_cc),
+	SFP_QUIRK_F("Turris", "RTSFP-2.5G", sfp_fixup_rollball),
 	SFP_QUIRK_F("Turris", "RTSFP-10", sfp_fixup_rollball),
 	SFP_QUIRK_F("Turris", "RTSFP-10G", sfp_fixup_rollball),
 };
Signature · 1 line
2.42.1
maintainer Reviewed-by on v3 6/6
#13 lore raw

Re: [PATCH v3 net-next 6/6] net: sfp: add quirk for another multigig RollBall transceiver

Quoted 7 lines · Eric Woudstra

From: Marek Behún <[email protected]>

Add quirk for another RollBall copper transceiver: Turris RTSFP-2.5G, containing 2.5g capable RTL8221B PHY.

Thanks!

Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!