Skip to contentSkip to conversation

Add RK816 PMIC support

PATCH Applied Alex Bee 4 participants 17 messages Apr 16, 2024 – May 10, 2024

Subsystems (6)
lore
Share & tools
lore

Alex Bee

author
#0 lore raw

v4 cover Add RK816 PMIC support

This series aims to add support for Rockchip RK816 PMIC series. As per datasheet it's targeted for RK3126/RK3128 (RK816-1), RK1108 (RK816-2) and PX3-SE (RK816-3) but might be used for other SoCs as well. The MFD consists of an integrated RTC, a GPIO controller, two 32k clock outputs, a power key, 3 buck- and 6 ldo regulators, 3 regulator-switches, and charger with integrated fuel gauge. Charger and fuel gauge are not part of this series. Two of the switches (otg/boost) are part of the binding, but not of the driver. They must only ever be enabled if no battery charging is happening, but it will be enabled automatically if a battery is attached and an external power source is connected. Thus that needs some incorporation of a yet to be added charger driver.
Integration in the existing rk8xx-infrastructure was pretty straightforward and only needed very little tweaking. In order to not further bloat the driver(s) too much with additional #defines I tried to re-use existing ones wherever possible.

The patches are loosely based on the vendor's implementation, verified against the datasheet and tested/measured on a RK3126 board.

I'd like to gently ping pinctrl and regulator maintainers: please have a look at this series. I've now added Sebastian Reichel to the recipients, as he recently added RK806 support and re-worked parts of the rk8xx drivers.

changes since v1:
- integrated Krzysztof's feedback for the bindings and the resulting driver changes
- fixed a sparse warning

link to v1:
https://lore.kernel.org/lkml/[email protected]/

changes since v2:
- integrated Krzysztof's feedback to v2 of the bindings and the resulting driver changes

link to v2:
https://lore.kernel.org/lkml/[email protected]/

changes since v3:
- integrated Krzysztof's feedback to the bindings of v3
- integrated Lee's feedback to the mfd part of v3

link to v3:
https://lore.kernel.org/lkml/[email protected]/

Please see individual patches for details about the changes.

Alex Bee (5):
dt-bindings: mfd: Add rk816 binding
mfd: rk8xx: Add RK816 support
pinctrl: rk805: Add rk816 pinctrl support
regulator: rk808: Support apply_bit for
rk808_set_suspend_voltage_range
regulator: rk808: Add RK816 support

 .../bindings/mfd/rockchip,rk816.yaml          | 274 ++++++++++++++++++
 drivers/mfd/Kconfig                           |   4 +-
 drivers/mfd/rk8xx-core.c                      | 104 +++++++
 drivers/mfd/rk8xx-i2c.c                       |  45 ++-
 drivers/pinctrl/pinctrl-rk805.c               |  69 +++++
 drivers/regulator/rk808-regulator.c           | 218 +++++++++++++-
 include/linux/mfd/rk808.h                     | 144 +++++++++
 7 files changed, 851 insertions(+), 7 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mfd/rockchip,rk816.yaml
Signature · 1 line
2.43.2
author
#1 lore raw

PATCH v4 1/5 dt-bindings: mfd: Add rk816 binding

Add DT binding document for Rockchip's RK816 PMIC

---
changes since v1:
- lowercase/hyphens for regulator node names
- rename "-reg" to "-regulator" to make node names generic
- dropped superfluous description for clock-output-names and wakeup-source
- dropped "|" for text blocks that don't require to preserve formatting
- use full path for $refs
- added pins description to the binding
- added charger function to description

changes since v2:
- dropped "-regulator"-suffix from regulator device names
- use "'"-quotes consistently in the binding
- dropped "pin_fun"-prefix from pin-function names
- added pin to example

changes since v3:
- made "unevaluatedProperties: false" to "additionalProperties: false" for regulators node
- added RB-tag

 .../bindings/mfd/rockchip,rk816.yaml          | 274 ++++++++++++++++++
 1 file changed, 274 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/rockchip,rk816.yaml
Documentation/devicetree/bindings/mfd/rockchip,rk816.yaml new file +274 -0
new file mode 100644
index 000000000000..0676890f101e
@@ -0,0 +1,274 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/rockchip,rk816.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: RK816 Power Management Integrated Circuit
+
+maintainers:
+  - Chris Zhong <[email protected]>
+  - Zhang Qing <[email protected]>
+
+description:
+  Rockchip RK816 series PMIC. This device consists of an i2c controlled MFD
+  that includes regulators, a RTC, a GPIO controller, a power button, and a
+  battery charger manager with fuel gauge.
+
+properties:
+  compatible:
+    enum:
+      - rockchip,rk816
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  '#clock-cells':
+    description:
+      See <dt-bindings/clock/rockchip,rk808.h> for clock IDs.
+    const: 1
+
+  clock-output-names:
+    maxItems: 2
+
+  gpio-controller: true
+
+  '#gpio-cells':
+    const: 2
+
+  system-power-controller:
+    type: boolean
+    description:
+      Telling whether or not this PMIC is controlling the system power.
+
+  wakeup-source:
+    type: boolean
+
+  vcc1-supply:
+    description:
+      The input supply for dcdc1.
+
+  vcc2-supply:
+    description:
+      The input supply for dcdc2.
+
+  vcc3-supply:
+    description:
+      The input supply for dcdc3.
+
+  vcc4-supply:
+    description:
+      The input supply for dcdc4.
+
+  vcc5-supply:
+    description:
+      The input supply for ldo1, ldo2, and ldo3.
+
+  vcc6-supply:
+    description:
+      The input supply for ldo4, ldo5, and ldo6.
+
+  vcc7-supply:
+    description:
+      The input supply for boost.
+
+  vcc8-supply:
+    description:
+      The input supply for otg-switch.
+
+  regulators:
+    type: object
+    patternProperties:
+      '^(boost|dcdc[1-4]|ldo[1-6]|otg-switch)$':
+        type: object
+        $ref: /schemas/regulator/regulator.yaml#
+        unevaluatedProperties: false
+    additionalProperties: false
+
+patternProperties:
+  '-pins$':
+    type: object
+    additionalProperties: false
+    $ref: /schemas/pinctrl/pinmux-node.yaml
+
+    properties:
+      function:
+        enum: [gpio, thermistor]
+
+      pins:
+        $ref: /schemas/types.yaml#/definitions/string
+        const: gpio0
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - '#clock-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/pinctrl/rockchip.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        rk816: pmic@1a {
+            compatible = "rockchip,rk816";
+            reg = <0x1a>;
+            interrupt-parent = <&gpio0>;
+            interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;
+            clock-output-names = "xin32k", "rk816-clkout2";
+            pinctrl-names = "default";
+            pinctrl-0 = <&pmic_int_l>;
+            gpio-controller;
+            system-power-controller;
+            wakeup-source;
+            #clock-cells = <1>;
+            #gpio-cells = <2>;
+
+            vcc1-supply = <&vcc_sys>;
+            vcc2-supply = <&vcc_sys>;
+            vcc3-supply = <&vcc_sys>;
+            vcc4-supply = <&vcc_sys>;
+            vcc5-supply = <&vcc33_io>;
+            vcc6-supply = <&vcc_sys>;
+
+            regulators {
+                vdd_cpu: dcdc1 {
+                    regulator-name = "vdd_cpu";
+                    regulator-min-microvolt = <750000>;
+                    regulator-max-microvolt = <1450000>;
+                    regulator-ramp-delay = <6001>;
+                    regulator-initial-mode = <1>;
+                    regulator-always-on;
+                    regulator-boot-on;
+
+                    regulator-state-mem {
+                        regulator-off-in-suspend;
+                    };
+                };
+
+                vdd_logic: dcdc2 {
+                    regulator-name = "vdd_logic";
+                    regulator-min-microvolt = <800000>;
+                    regulator-max-microvolt = <1250000>;
+                    regulator-ramp-delay = <6001>;
+                    regulator-initial-mode = <1>;
+                    regulator-always-on;
+                    regulator-boot-on;
+
+                    regulator-state-mem {
+                        regulator-on-in-suspend;
+                        regulator-suspend-microvolt = <1000000>;
+                    };
+                };
+
+                vcc_ddr: dcdc3 {
+                    regulator-name = "vcc_ddr";
+                    regulator-initial-mode = <1>;
+                    regulator-always-on;
+                    regulator-boot-on;
+
+                    regulator-state-mem {
+                        regulator-on-in-suspend;
+                    };
+                };
+
+                vcc33_io: dcdc4 {
+                    regulator-min-microvolt = <3300000>;
+                    regulator-max-microvolt = <3300000>;
+                    regulator-name = "vcc33_io";
+                    regulator-initial-mode = <1>;
+                    regulator-always-on;
+                    regulator-boot-on;
+
+                    regulator-state-mem {
+                        regulator-on-in-suspend;
+                        regulator-suspend-microvolt = <3300000>;
+                    };
+                };
+
+                vccio_pmu: ldo1 {
+                    regulator-min-microvolt = <3300000>;
+                    regulator-max-microvolt = <3300000>;
+                    regulator-name = "vccio_pmu";
+                    regulator-always-on;
+                    regulator-boot-on;
+
+                    regulator-state-mem {
+                        regulator-on-in-suspend;
+                        regulator-suspend-microvolt = <3300000>;
+                    };
+                };
+
+                vcc_tp: ldo2 {
+                    regulator-min-microvolt = <3300000>;
+                    regulator-max-microvolt = <3300000>;
+                    regulator-name = "vcc_tp";
+
+                    regulator-state-mem {
+                        regulator-off-in-suspend;
+                    };
+                };
+
+                vdd_10: ldo3 {
+                    regulator-min-microvolt = <1000000>;
+                    regulator-max-microvolt = <1000000>;
+                    regulator-name = "vdd_10";
+                    regulator-always-on;
+                    regulator-boot-on;
+
+                    regulator-state-mem {
+                        regulator-on-in-suspend;
+                        regulator-suspend-microvolt = <1000000>;
+                    };
+                };
+
+                vcc18_lcd: ldo4 {
+                    regulator-min-microvolt = <1800000>;
+                    regulator-max-microvolt = <1800000>;
+                    regulator-name = "vcc18_lcd";
+
+                    regulator-state-mem {
+                        regulator-on-in-suspend;
+                        regulator-suspend-microvolt = <1800000>;
+                    };
+                };
+
+                vccio_sd: ldo5 {
+                    regulator-min-microvolt = <1800000>;
+                    regulator-max-microvolt = <3300000>;
+                    regulator-name = "vccio_sd";
+
+                    regulator-state-mem {
+                        regulator-on-in-suspend;
+                        regulator-suspend-microvolt = <3300000>;
+                    };
+                };
+
+                vdd10_lcd: ldo6 {
+                    regulator-min-microvolt = <1000000>;
+                    regulator-max-microvolt = <1000000>;
+                    regulator-name = "vdd10_lcd";
+
+                    regulator-state-mem {
+                        regulator-on-in-suspend;
+                        regulator-suspend-microvolt = <1000000>;
+                    };
+                };
+            };
+
+            rk816_gpio_pins: gpio-pins {
+                function = "gpio";
+                pins = "gpio0";
+            };
+        };
+    };
Signature · 1 line
2.43.2
author
#2 lore raw

PATCH v4 2/5 mfd: rk8xx: Add RK816 support

In reply to Alex Bee

This integrates RK816 support in the this existing rk8xx mfd driver.

This version has unaligned interrupt registers, which requires to define a separate get_irq_reg callback for the regmap. Apart from that the integration is straightforward and the existing structures can be used as is. The initialization sequence has been taken from vendor kernel.

---
chnages since v1:
- un-constify rk816_get_irq_reg's return type

chnages since v3:
- added RK816_IRQ_STS_OFFSET/RK816_IRQ_MSK_OFFSET macros
- codestyle fix

 drivers/mfd/Kconfig       |   4 +-
 drivers/mfd/rk8xx-core.c  | 104 +++++++++++++++++++++++++++
 drivers/mfd/rk8xx-i2c.c   |  45 +++++++++++-
 include/linux/mfd/rk808.h | 144 ++++++++++++++++++++++++++++++++++++++
 4 files changed, 294 insertions(+), 3 deletions(-)
drivers/mfd/Kconfig +2 -2
index 00fd388a9205..266b4f54af60 100644
@@ -1225,7 +1225,7 @@ config MFD_RK8XX
 	select MFD_CORE
 
 config MFD_RK8XX_I2C
-	tristate "Rockchip RK805/RK808/RK809/RK817/RK818 Power Management Chip"
+	tristate "Rockchip RK805/RK808/RK809/RK816/RK817/RK818 Power Management Chip"
 	depends on I2C && OF
 	select MFD_CORE
 	select REGMAP_I2C
@@ -1233,7 +1233,7 @@ config MFD_RK8XX_I2C
 	select MFD_RK8XX
 	help
 	  If you say yes here you get support for the RK805, RK808, RK809,
-	  RK817 and RK818 Power Management chips.
+	  RK816, RK817 and RK818 Power Management chips.
 	  This driver provides common support for accessing the device
 	  through I2C interface. The device supports multiple sub-devices
 	  including interrupts, RTC, LDO & DCDC regulators, and onkey.
drivers/mfd/rk8xx-core.c +104 -0

146 lines not on this page · raw message

drivers/mfd/rk8xx-i2c.c +44 -1

74 lines not on this page · raw message

include/linux/mfd/rk808.h +144 -0

162 lines not on this page · raw message

Signature · 1 line
2.43.2
author
#3 lore raw

PATCH v4 3/5 pinctrl: rk805: Add rk816 pinctrl support

In reply to Alex Bee

This adds support for RK816 to the exising rk805 pinctrl driver

It has a single pin which can be configured as input from a thermistor (for instance in an attached battery) or as a gpio.

---
changes since v1:
- rename pin-function names according to the updated binding
- added missing fun_reg for rk816_gpio_cfgs

changes since v2:
- aligned pin-function names with binding (dropped "pin_fun"-prefix)

 drivers/pinctrl/pinctrl-rk805.c | 69 +++++++++++++++++++++++++++++++++
 1 file changed, 69 insertions(+)
drivers/pinctrl/pinctrl-rk805.c +69 -0
index 56d916f2cee6..c42f1bf93404 100644
@@ -93,6 +93,11 @@ enum rk806_pinmux_option {
 	RK806_PINMUX_FUN5,
 };
 
+enum rk816_pinmux_option {
+	RK816_PINMUX_THERMISTOR,
+	RK816_PINMUX_GPIO,
+};
+
 enum {
 	RK805_GPIO0,
 	RK805_GPIO1,
@@ -104,6 +109,10 @@ enum {
 	RK806_GPIO_DVS3
 };
 
+enum {
+	RK816_GPIO0,
+};
+
 static const char *const rk805_gpio_groups[] = {
 	"gpio0",
 	"gpio1",
@@ -115,6 +124,10 @@ static const char *const rk806_gpio_groups[] = {
 	"gpio_pwrctrl3",
 };
 
+static const char *const rk816_gpio_groups[] = {
+	"gpio0",
+};
+
 /* RK805: 2 output only GPIOs */
 static const struct pinctrl_pin_desc rk805_pins_desc[] = {
 	PINCTRL_PIN(RK805_GPIO0, "gpio0"),
@@ -128,6 +141,11 @@ static const struct pinctrl_pin_desc rk806_pins_desc[] = {
 	PINCTRL_PIN(RK806_GPIO_DVS3, "gpio_pwrctrl3"),
 };
 
+/* RK816 */
+static const struct pinctrl_pin_desc rk816_pins_desc[] = {
+	PINCTRL_PIN(RK816_GPIO0, "gpio0"),
+};
+
 static const struct rk805_pin_function rk805_pin_functions[] = {
 	{
 		.name = "gpio",
@@ -176,6 +194,21 @@ static const struct rk805_pin_function rk806_pin_functions[] = {
 	},
 };
 
+static const struct rk805_pin_function rk816_pin_functions[] = {
+	{
+		.name = "gpio",
+		.groups = rk816_gpio_groups,
+		.ngroups = ARRAY_SIZE(rk816_gpio_groups),
+		.mux_option = RK816_PINMUX_GPIO,
+	},
+	{
+		.name = "thermistor",
+		.groups = rk816_gpio_groups,
+		.ngroups = ARRAY_SIZE(rk816_gpio_groups),
+		.mux_option = RK816_PINMUX_THERMISTOR,
+	},
+};
+
 static const struct rk805_pin_group rk805_pin_groups[] = {
 	{
 		.name = "gpio0",
@@ -207,6 +240,14 @@ static const struct rk805_pin_group rk806_pin_groups[] = {
 	}
 };
 
+static const struct rk805_pin_group rk816_pin_groups[] = {
+	{
+		.name = "gpio0",
+		.pins = { RK816_GPIO0 },
+		.npins = 1,
+	},
+};
+
 #define RK805_GPIO0_VAL_MSK	BIT(0)
 #define RK805_GPIO1_VAL_MSK	BIT(1)
 
@@ -255,6 +296,20 @@ static struct rk805_pin_config rk806_gpio_cfgs[] = {
 	}
 };
 
+#define RK816_FUN_MASK		BIT(2)
+#define RK816_VAL_MASK		BIT(3)
+#define RK816_DIR_MASK		BIT(4)
+
+static struct rk805_pin_config rk816_gpio_cfgs[] = {
+	{
+		.fun_reg = RK818_IO_POL_REG,
+		.fun_msk = RK816_FUN_MASK,
+		.reg = RK818_IO_POL_REG,
+		.val_msk = RK816_VAL_MASK,
+		.dir_msk = RK816_DIR_MASK,
+	},
+};
+
 /* generic gpio chip */
 static int rk805_gpio_get(struct gpio_chip *chip, unsigned int offset)
 {
@@ -439,6 +494,8 @@ static int rk805_pinctrl_gpio_request_enable(struct pinctrl_dev *pctldev,
 		return _rk805_pinctrl_set_mux(pctldev, offset, RK805_PINMUX_GPIO);
 	case RK806_ID:
 		return _rk805_pinctrl_set_mux(pctldev, offset, RK806_PINMUX_FUN5);
+	case RK816_ID:
+		return _rk805_pinctrl_set_mux(pctldev, offset, RK816_PINMUX_GPIO);
 	}
 
 	return -ENOTSUPP;
@@ -588,6 +645,18 @@ static int rk805_pinctrl_probe(struct platform_device *pdev)
 		pci->pin_cfg = rk806_gpio_cfgs;
 		pci->gpio_chip.ngpio = ARRAY_SIZE(rk806_gpio_cfgs);
 		break;
+	case RK816_ID:
+		pci->pins = rk816_pins_desc;
+		pci->num_pins = ARRAY_SIZE(rk816_pins_desc);
+		pci->functions = rk816_pin_functions;
+		pci->num_functions = ARRAY_SIZE(rk816_pin_functions);
+		pci->groups = rk816_pin_groups;
+		pci->num_pin_groups = ARRAY_SIZE(rk816_pin_groups);
+		pci->pinctrl_desc.pins = rk816_pins_desc;
+		pci->pinctrl_desc.npins = ARRAY_SIZE(rk816_pins_desc);
+		pci->pin_cfg = rk816_gpio_cfgs;
+		pci->gpio_chip.ngpio = ARRAY_SIZE(rk816_gpio_cfgs);
+		break;
 	default:
 		dev_err(&pdev->dev, "unsupported RK805 ID %lu\n",
 			pci->rk808->variant);
Signature · 1 line
2.43.2
#4 lore raw

Re: [PATCH v4 3/5] pinctrl: rk805: Add rk816 pinctrl support

Quoted 6 lines · Alex Bee

This adds support for RK816 to the exising rk805 pinctrl driver

It has a single pin which can be configured as input from a thermistor (for instance in an attached battery) or as a gpio.

Looks good to me, is this patch something I can just merge once the maintainers have reviewed it?

Yours,
Linus Walleij

author
#5 lore raw

Re: [PATCH v4 3/5] pinctrl: rk805: Add rk816 pinctrl support

Hi Linus

Am 17.04.24 um 10:57 schrieb Linus Walleij:

Quoted 10 lines · Alex Bee
Quoted 7 lines

This adds support for RK816 to the exising rk805 pinctrl driver

It has a single pin which can be configured as input from a thermistor (for instance in an attached battery) or as a gpio.

Looks good to me, is this patch something I can just merge once the maintainers have reviewed it?

This patch depends on the mfd patch as it includes some definitions which are used here. Same is true for the regulator patch. So I guess this whole series has to go via the mfd tree and it would be probably the best if the other subsystem maintainers could ack/review the other patches.

Regards,
Alex

Quoted 3 lines

Yours,
Linus Walleij

Reviewed-by on v4 3/5
#6 lore raw

Re: [PATCH v4 3/5] pinctrl: rk805: Add rk816 pinctrl support

In reply to Alex Bee
Quoted 6 lines · Alex Bee

This adds support for RK816 to the exising rk805 pinctrl driver

It has a single pin which can be configured as input from a thermistor (for instance in an attached battery) or as a gpio.

Lee: pls apply with the rest to the MFD subsystem when you are happy with the patches.

Yours,
Linus Walleij

author
#7 lore raw

PATCH v4 4/5 regulator: rk808: Support apply_bit for rk808_set_suspend_voltage_range

In reply to Alex Bee

rk808_set_suspend_voltage_range currently does not account the existence of apply_bit/apply_reg.

This adds support for those in same way it is done in regulator_set_voltage_sel_regmap and is required for the upcoming RK816 support

---
changes since v1:
- none

 drivers/regulator/rk808-regulator.c | 16 +++++++++++++---
 1 file changed, 13 insertions(+), 3 deletions(-)
drivers/regulator/rk808-regulator.c +13 -3
index d89ae7f16d7a..a6a563e402d0 100644
@@ -534,15 +534,25 @@ static int rk808_set_suspend_voltage_range(struct regulator_dev *rdev, int uv)
 {
 	unsigned int reg;
 	int sel = regulator_map_voltage_linear_range(rdev, uv, uv);
+	int ret;
 
 	if (sel < 0)
 		return -EINVAL;
 
 	reg = rdev->desc->vsel_reg + RK808_SLP_REG_OFFSET;
 
-	return regmap_update_bits(rdev->regmap, reg,
-				  rdev->desc->vsel_mask,
-				  sel);
+	ret = regmap_update_bits(rdev->regmap, reg,
+				 rdev->desc->vsel_mask,
+				 sel);
+	if (ret)
+		return ret;
+
+	if (rdev->desc->apply_bit)
+		ret = regmap_update_bits(rdev->regmap, rdev->desc->apply_reg,
+					 rdev->desc->apply_bit,
+					 rdev->desc->apply_bit);
+
+	return ret;
 }
 
 static int rk805_set_suspend_enable(struct regulator_dev *rdev)
Signature · 1 line
2.43.2
maintainer Acked-by on v4 4/5
#8 lore raw

Re: [PATCH v4 4/5] regulator: rk808: Support apply_bit for rk808_set_suspend_voltage_range

Quoted 6 lines · Alex Bee

rk808_set_suspend_voltage_range currently does not account the existence of apply_bit/apply_reg.

This adds support for those in same way it is done in regulator_set_voltage_sel_regmap and is required for the upcoming RK816 support

author
#9 lore raw

PATCH v4 5/5 regulator: rk808: Add RK816 support

In reply to Alex Bee

Add support for rk816 to the existing rk808 regulator driver.

The infrastructure of the driver can be re-used as is. A peculiarity for this version is, that BUCK1/BUCK2 have a (common) bit which needs to toggled after a voltage change to confirm the change. Regulator regmap takes care of that by defining a apply_bit and apply_reg for those regulators.

---
changes since v1:
- align regulator's .name and .of_match with updated binding

changes since v2:
- align regulator's .name and .of_match with updated binding (dropped "-regulator" prefix)

 drivers/regulator/rk808-regulator.c | 202 +++++++++++++++++++++++++++-
 1 file changed, 201 insertions(+), 1 deletion(-)
drivers/regulator/rk808-regulator.c +201 -1
index a6a563e402d0..14b60abd6afc 100644
@@ -158,6 +158,11 @@
 	RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg,	\
 	_vmask, _ereg, _emask, 0, 0, _etime, &rk808_reg_ops)
 
+#define RK816_DESC(_id, _match, _supply, _min, _max, _step, _vreg,	\
+	_vmask, _ereg, _emask, _disval, _etime)				\
+	RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg,	\
+	_vmask, _ereg, _emask, _emask, _disval, _etime, &rk816_reg_ops)
+
 #define RK817_DESC(_id, _match, _supply, _min, _max, _step, _vreg,	\
 	_vmask, _ereg, _emask, _disval, _etime)				\
 	RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg,	\
@@ -258,7 +263,7 @@ static const unsigned int rk808_buck1_2_ramp_table[] = {
 	2000, 4000, 6000, 10000
 };
 
-/* RK817 RK809 */
+/* RK817/RK809/RK816 (buck 1/2 only) */
 static const unsigned int rk817_buck1_4_ramp_table[] = {
 	3000, 6300, 12500, 25000
 };
@@ -640,6 +645,38 @@ static int rk808_set_suspend_disable(struct regulator_dev *rdev)
 				  rdev->desc->enable_mask);
 }
 
+static const struct rk8xx_register_bit rk816_suspend_bits[] = {
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 0),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 1),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 2),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 3),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 0),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 1),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 2),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 3),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 4),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG2, 5),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 5),
+	RK8XX_REG_BIT(RK818_SLEEP_SET_OFF_REG1, 6),
+};
+
+static int rk816_set_suspend_enable(struct regulator_dev *rdev)
+{
+	int rid = rdev_get_id(rdev);
+
+	return regmap_update_bits(rdev->regmap, rk816_suspend_bits[rid].reg,
+				  rk816_suspend_bits[rid].bit,
+				  rk816_suspend_bits[rid].bit);
+}
+
+static int rk816_set_suspend_disable(struct regulator_dev *rdev)
+{
+	int rid = rdev_get_id(rdev);
+
+	return regmap_update_bits(rdev->regmap, rk816_suspend_bits[rid].reg,
+				  rk816_suspend_bits[rid].bit, 0);
+}
+
 static int rk817_set_suspend_enable_ctrl(struct regulator_dev *rdev,
 					 unsigned int en)
 {
@@ -913,6 +950,54 @@ static const struct regulator_ops rk809_buck5_ops_range = {
 	.set_suspend_disable	= rk817_set_suspend_disable,
 };
 
+static const struct regulator_ops rk816_buck1_2_ops_ranges = {
+	.list_voltage		= regulator_list_voltage_linear_range,
+	.map_voltage		= regulator_map_voltage_linear_range,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+	.set_voltage_time_sel	= regulator_set_voltage_time_sel,
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.is_enabled		= regulator_is_enabled_regmap,
+	.set_mode		= rk8xx_set_mode,
+	.get_mode		= rk8xx_get_mode,
+	.set_suspend_mode	= rk8xx_set_suspend_mode,
+	.set_ramp_delay		= regulator_set_ramp_delay_regmap,
+	.set_suspend_voltage	= rk808_set_suspend_voltage_range,
+	.set_suspend_enable	= rk816_set_suspend_enable,
+	.set_suspend_disable	= rk816_set_suspend_disable,
+};
+
+static const struct regulator_ops rk816_buck4_ops_ranges = {
+	.list_voltage		= regulator_list_voltage_linear_range,
+	.map_voltage		= regulator_map_voltage_linear_range,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+	.set_voltage_time_sel	= regulator_set_voltage_time_sel,
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.is_enabled		= regulator_is_enabled_regmap,
+	.set_mode		= rk8xx_set_mode,
+	.get_mode		= rk8xx_get_mode,
+	.set_suspend_mode	= rk8xx_set_suspend_mode,
+	.set_suspend_voltage	= rk808_set_suspend_voltage_range,
+	.set_suspend_enable	= rk816_set_suspend_enable,
+	.set_suspend_disable	= rk816_set_suspend_disable,
+};
+
+static const struct regulator_ops rk816_reg_ops = {
+	.list_voltage		= regulator_list_voltage_linear,
+	.map_voltage		= regulator_map_voltage_linear,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.is_enabled		= rk8xx_is_enabled_wmsk_regmap,
+	.set_suspend_voltage	= rk808_set_suspend_voltage,
+	.set_suspend_enable	= rk816_set_suspend_enable,
+	.set_suspend_disable	= rk816_set_suspend_disable,
+};
+
 static const struct regulator_ops rk817_reg_ops = {
 	.list_voltage		= regulator_list_voltage_linear,
 	.map_voltage		= regulator_map_voltage_linear,
@@ -1392,6 +1477,117 @@ static const struct regulator_desc rk809_reg[] = {
 			  DISABLE_VAL(3)),
 };
 
+static const struct linear_range rk816_buck_4_voltage_ranges[] = {
+	REGULATOR_LINEAR_RANGE(800000, 0, 26, 100000),
+	REGULATOR_LINEAR_RANGE(3500000, 27, 31, 0),
+};
+
+static const struct regulator_desc rk816_reg[] = {
+	{
+		.name = "dcdc1",
+		.supply_name = "vcc1",
+		.of_match = of_match_ptr("dcdc1"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = RK816_ID_DCDC1,
+		.ops = &rk816_buck1_2_ops_ranges,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = 64,
+		.linear_ranges = rk805_buck_1_2_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(rk805_buck_1_2_voltage_ranges),
+		.vsel_reg = RK818_BUCK1_ON_VSEL_REG,
+		.vsel_mask = RK818_BUCK_VSEL_MASK,
+		.apply_reg = RK816_DCDC_EN_REG2,
+		.apply_bit = RK816_BUCK_DVS_CONFIRM,
+		.enable_reg = RK816_DCDC_EN_REG1,
+		.enable_mask = BIT(4) | BIT(0),
+		.enable_val = BIT(4) | BIT(0),
+		.disable_val = BIT(4),
+		.ramp_reg = RK818_BUCK1_CONFIG_REG,
+		.ramp_mask = RK808_RAMP_RATE_MASK,
+		.ramp_delay_table = rk817_buck1_4_ramp_table,
+		.n_ramp_values = ARRAY_SIZE(rk817_buck1_4_ramp_table),
+		.of_map_mode = rk8xx_regulator_of_map_mode,
+		.owner = THIS_MODULE,
+	}, {
+		.name = "dcdc2",
+		.supply_name = "vcc2",
+		.of_match = of_match_ptr("dcdc2"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = RK816_ID_DCDC2,
+		.ops = &rk816_buck1_2_ops_ranges,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = 64,
+		.linear_ranges = rk805_buck_1_2_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(rk805_buck_1_2_voltage_ranges),
+		.vsel_reg = RK818_BUCK2_ON_VSEL_REG,
+		.vsel_mask = RK818_BUCK_VSEL_MASK,
+		.apply_reg = RK816_DCDC_EN_REG2,
+		.apply_bit = RK816_BUCK_DVS_CONFIRM,
+		.enable_reg = RK816_DCDC_EN_REG1,
+		.enable_mask = BIT(5) | BIT(1),
+		.enable_val = BIT(5) | BIT(1),
+		.disable_val = BIT(5),
+		.ramp_reg = RK818_BUCK2_CONFIG_REG,
+		.ramp_mask = RK808_RAMP_RATE_MASK,
+		.ramp_delay_table = rk817_buck1_4_ramp_table,
+		.n_ramp_values = ARRAY_SIZE(rk817_buck1_4_ramp_table),
+		.of_map_mode = rk8xx_regulator_of_map_mode,
+		.owner = THIS_MODULE,
+	}, {
+		.name = "dcdc3",
+		.supply_name = "vcc3",
+		.of_match = of_match_ptr("dcdc3"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = RK816_ID_DCDC3,
+		.ops = &rk808_switch_ops,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = 1,
+		.enable_reg = RK816_DCDC_EN_REG1,
+		.enable_mask = BIT(6) | BIT(2),
+		.enable_val =  BIT(6) | BIT(2),
+		.disable_val = BIT(6),
+		.of_map_mode = rk8xx_regulator_of_map_mode,
+		.owner = THIS_MODULE,
+	}, {
+		.name = "dcdc4",
+		.supply_name = "vcc4",
+		.of_match = of_match_ptr("dcdc4"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = RK816_ID_DCDC4,
+		.ops = &rk816_buck4_ops_ranges,
+		.type = REGULATOR_VOLTAGE,
+		.n_voltages = 32,
+		.linear_ranges = rk816_buck_4_voltage_ranges,
+		.n_linear_ranges = ARRAY_SIZE(rk816_buck_4_voltage_ranges),
+		.vsel_reg = RK818_BUCK4_ON_VSEL_REG,
+		.vsel_mask = RK818_BUCK4_VSEL_MASK,
+		.enable_reg = RK816_DCDC_EN_REG1,
+		.enable_mask = BIT(7) | BIT(3),
+		.enable_val = BIT(7) | BIT(3),
+		.disable_val = BIT(7),
+		.of_map_mode = rk8xx_regulator_of_map_mode,
+		.owner = THIS_MODULE,
+	},
+	RK816_DESC(RK816_ID_LDO1, "ldo1", "vcc5", 800, 3400, 100,
+		   RK818_LDO1_ON_VSEL_REG, RK818_LDO_VSEL_MASK,
+		   RK816_LDO_EN_REG1, ENABLE_MASK(0), DISABLE_VAL(0), 400),
+	RK816_DESC(RK816_ID_LDO2, "ldo2", "vcc5", 800, 3400, 100,
+		   RK818_LDO2_ON_VSEL_REG, RK818_LDO_VSEL_MASK,
+		   RK816_LDO_EN_REG1, ENABLE_MASK(1), DISABLE_VAL(1), 400),
+	RK816_DESC(RK816_ID_LDO3, "ldo3", "vcc5", 800, 3400, 100,
+		   RK818_LDO3_ON_VSEL_REG, RK818_LDO_VSEL_MASK,
+		   RK816_LDO_EN_REG1, ENABLE_MASK(2), DISABLE_VAL(2), 400),
+	RK816_DESC(RK816_ID_LDO4, "ldo4", "vcc6", 800, 3400, 100,
+		   RK818_LDO4_ON_VSEL_REG, RK818_LDO_VSEL_MASK,
+		   RK816_LDO_EN_REG1, ENABLE_MASK(3), DISABLE_VAL(3), 400),
+	RK816_DESC(RK816_ID_LDO5, "ldo5", "vcc6", 800, 3400, 100,
+		   RK818_LDO5_ON_VSEL_REG, RK818_LDO_VSEL_MASK,
+		   RK816_LDO_EN_REG2, ENABLE_MASK(0), DISABLE_VAL(0), 400),
+	RK816_DESC(RK816_ID_LDO6, "ldo6", "vcc6", 800, 3400, 100,
+		   RK818_LDO6_ON_VSEL_REG, RK818_LDO_VSEL_MASK,
+		   RK816_LDO_EN_REG2, ENABLE_MASK(1), DISABLE_VAL(1), 400),
+};
+
 static const struct regulator_desc rk817_reg[] = {
 	{
 		.name = "DCDC_REG1",
@@ -1714,6 +1910,10 @@ static int rk808_regulator_probe(struct platform_device *pdev)
 		regulators = rk809_reg;
 		nregulators = RK809_NUM_REGULATORS;
 		break;
+	case RK816_ID:
+		regulators = rk816_reg;
+		nregulators = ARRAY_SIZE(rk816_reg);
+		break;
 	case RK817_ID:
 		regulators = rk817_reg;
 		nregulators = RK817_NUM_REGULATORS;
Signature · 1 line
2.43.2
maintainer Reviewed-by on v4 5/5
#10 lore raw

Re: [PATCH v4 5/5] regulator: rk808: Add RK816 support

Quoted 7 lines · Alex Bee

Add support for rk816 to the existing rk808 regulator driver.

The infrastructure of the driver can be re-used as is. A peculiarity for this version is, that BUCK1/BUCK2 have a (common) bit which needs to toggled after a voltage change to confirm the change. Regulator regmap takes care of that by defining a apply_bit and apply_reg for those regulators.

author
#11 lore raw
In reply to Alex Bee

Hi Lee,

it looks like all patches except the MFD ones have been reviewed/acked by now. I hope I integrated your feedback to v3 [0] in a way you were expecting. Also I was hoping this whole series could be go though the MFD tree, since all the none-MFD patches depend on the changes mfd-header.

Please let me know if there is anything left for me to do.

Thanks,

Alex

[0] https://lore.kernel.org/lkml/[email protected]/T/#m1bb23196c192289f898aebc64ccf62edb9ef5b5a

Am 16.04.24 um 18:12 schrieb Alex Bee:

Quoted 65 lines

This series aims to add support for Rockchip RK816 PMIC series. As per datasheet it's targeted for RK3126/RK3128 (RK816-1), RK1108 (RK816-2) and PX3-SE (RK816-3) but might be used for other SoCs as well. The MFD consists of an integrated RTC, a GPIO controller, two 32k clock outputs, a power key, 3 buck- and 6 ldo regulators, 3 regulator-switches, and charger with integrated fuel gauge. Charger and fuel gauge are not part of this series. Two of the switches (otg/boost) are part of the binding, but not of the driver. They must only ever be enabled if no battery charging is happening, but it will be enabled automatically if a battery is attached and an external power source is connected. Thus that needs some incorporation of a yet to be added charger driver.
Integration in the existing rk8xx-infrastructure was pretty straightforward and only needed very little tweaking. In order to not further bloat the driver(s) too much with additional #defines I tried to re-use existing ones wherever possible.

The patches are loosely based on the vendor's implementation, verified against the datasheet and tested/measured on a RK3126 board.

I'd like to gently ping pinctrl and regulator maintainers: please have a look at this series. I've now added Sebastian Reichel to the recipients, as he recently added RK806 support and re-worked parts of the rk8xx drivers.

changes since v1:
- integrated Krzysztof's feedback for the bindings and the resulting driver changes
- fixed a sparse warning

link to v1:
https://lore.kernel.org/lkml/[email protected]/

changes since v2:
- integrated Krzysztof's feedback to v2 of the bindings and the resulting driver changes

link to v2:
https://lore.kernel.org/lkml/[email protected]/

changes since v3:
- integrated Krzysztof's feedback to the bindings of v3
- integrated Lee's feedback to the mfd part of v3

link to v3:
https://lore.kernel.org/lkml/[email protected]/

Please see individual patches for details about the changes.

Alex Bee (5):--
dt-bindings: mfd: Add rk816 binding
mfd: rk8xx: Add RK816 support
pinctrl: rk805: Add rk816 pinctrl support
regulator: rk808: Support apply_bit for
rk808_set_suspend_voltage_range
regulator: rk808: Add RK816 support

  .../bindings/mfd/rockchip,rk816.yaml          | 274 ++++++++++++++++++
  drivers/mfd/Kconfig                           |   4 +-
  drivers/mfd/rk8xx-core.c                      | 104 +++++++
  drivers/mfd/rk8xx-i2c.c                       |  45 ++-
  drivers/pinctrl/pinctrl-rk805.c               |  69 +++++
  drivers/regulator/rk808-regulator.c           | 218 +++++++++++++-
  include/linux/mfd/rk808.h                     | 144 +++++++++
  7 files changed, 851 insertions(+), 7 deletions(-)

create mode 100644 Documentation/devicetree/bindings/mfd/rockchip,rk816.yaml

maintainer
#12 lore raw
Quoted 8 lines · Alex Bee

Hi Lee,

it looks like all patches except the MFD ones have been reviewed/acked by now. I hope I integrated your feedback to v3 [0] in a way you were expecting. Also I was hoping this whole series could be go though the MFD tree, since all the none-MFD patches depend on the changes mfd-header.

Please let me know if there is anything left for me to do.

I have the patch open 'right now', please bear with me.

Signature · 1 line
Lee Jones [李琼斯]
maintainer Applied
#13 lore raw
In reply to Alex Bee
Quoted 16 lines · Alex Bee

This series aims to add support for Rockchip RK816 PMIC series. As per datasheet it's targeted for RK3126/RK3128 (RK816-1), RK1108 (RK816-2) and PX3-SE (RK816-3) but might be used for other SoCs as well. The MFD consists of an integrated RTC, a GPIO controller, two 32k clock outputs, a power key, 3 buck- and 6 ldo regulators, 3 regulator-switches, and charger with integrated fuel gauge. Charger and fuel gauge are not part of this series. Two of the switches (otg/boost) are part of the binding, but not of the driver. They must only ever be enabled if no battery charging is happening, but it will be enabled automatically if a battery is attached and an external power source is connected. Thus that needs some incorporation of a yet to be added charger driver.
Integration in the existing rk8xx-infrastructure was pretty straightforward and only needed very little tweaking. In order to not further bloat the driver(s) too much with additional #defines I tried to re-use existing ones wherever possible.

Quoted 1 line

[...]

Applied, thanks!

[1/5] dt-bindings: mfd: Add rk816 binding

      commit: 06dfb41b1cf8d64327e5c4391e165f466506c4f0
[2/5] mfd: rk8xx: Add RK816 support
      commit: e9006f81faf8e438ea83626db578610e49f31576
[3/5] pinctrl: rk805: Add rk816 pinctrl support
      commit: 1bd97d64b5f0c01d03ecc9473ccfcf180dbbf54a
[4/5] regulator: rk808: Support apply_bit for rk808_set_suspend_voltage_range
      commit: 9f4e899c286b5127e2443d50e37ee2112efbfa2c
[5/5] regulator: rk808: Add RK816 support
      commit: 5eb068da74a0b443fb99a89d9e5062691649c470

--
Lee Jones [李琼斯]

maintainer
#14 lore raw
Quoted 22 lines · Lee Jones
Quoted 16 lines · Alex Bee

This series aims to add support for Rockchip RK816 PMIC series. As per datasheet it's targeted for RK3126/RK3128 (RK816-1), RK1108 (RK816-2) and PX3-SE (RK816-3) but might be used for other SoCs as well. The MFD consists of an integrated RTC, a GPIO controller, two 32k clock outputs, a power key, 3 buck- and 6 ldo regulators, 3 regulator-switches, and charger with integrated fuel gauge. Charger and fuel gauge are not part of this series. Two of the switches (otg/boost) are part of the binding, but not of the driver. They must only ever be enabled if no battery charging is happening, but it will be enabled automatically if a battery is attached and an external power source is connected. Thus that needs some incorporation of a yet to be added charger driver.
Integration in the existing rk8xx-infrastructure was pretty straightforward and only needed very little tweaking. In order to not further bloat the driver(s) too much with additional #defines I tried to re-use existing ones wherever possible.

Quoted 1 line

[...]

Applied, thanks!

[1/5] dt-bindings: mfd: Add rk816 binding

Quoted 9 lines
      commit: 06dfb41b1cf8d64327e5c4391e165f466506c4f0
[2/5] mfd: rk8xx: Add RK816 support
      commit: e9006f81faf8e438ea83626db578610e49f31576
[3/5] pinctrl: rk805: Add rk816 pinctrl support
      commit: 1bd97d64b5f0c01d03ecc9473ccfcf180dbbf54a
[4/5] regulator: rk808: Support apply_bit for rk808_set_suspend_voltage_range
      commit: 9f4e899c286b5127e2443d50e37ee2112efbfa2c
[5/5] regulator: rk808: Add RK816 support
      commit: 5eb068da74a0b443fb99a89d9e5062691649c470

Submitted for build testing.

If successful, I'll follow-up with a PR.

Signature · 1 line
Lee Jones [李琼斯]
author
#15 lore raw

Am 03.05.24 um 10:18 schrieb Lee Jones:

Quoted 32 lines · Lee Jones
Quoted 22 lines · Alex Bee
Quoted 16 lines

This series aims to add support for Rockchip RK816 PMIC series. As per datasheet it's targeted for RK3126/RK3128 (RK816-1), RK1108 (RK816-2) and PX3-SE (RK816-3) but might be used for other SoCs as well. The MFD consists of an integrated RTC, a GPIO controller, two 32k clock outputs, a power key, 3 buck- and 6 ldo regulators, 3 regulator-switches, and charger with integrated fuel gauge. Charger and fuel gauge are not part of this series. Two of the switches (otg/boost) are part of the binding, but not of the driver. They must only ever be enabled if no battery charging is happening, but it will be enabled automatically if a battery is attached and an external power source is connected. Thus that needs some incorporation of a yet to be added charger driver.
Integration in the existing rk8xx-infrastructure was pretty straightforward and only needed very little tweaking. In order to not further bloat the driver(s) too much with additional #defines I tried to re-use existing ones wherever possible.

Quoted 1 line

[...]

Applied, thanks!

[1/5] dt-bindings: mfd: Add rk816 binding

Quoted 9 lines
       commit: 06dfb41b1cf8d64327e5c4391e165f466506c4f0
[2/5] mfd: rk8xx: Add RK816 support
       commit: e9006f81faf8e438ea83626db578610e49f31576
[3/5] pinctrl: rk805: Add rk816 pinctrl support
       commit: 1bd97d64b5f0c01d03ecc9473ccfcf180dbbf54a
[4/5] regulator: rk808: Support apply_bit for rk808_set_suspend_voltage_range
       commit: 9f4e899c286b5127e2443d50e37ee2112efbfa2c
[5/5] regulator: rk808: Add RK816 support
       commit: 5eb068da74a0b443fb99a89d9e5062691649c470
Quoted 3 lines

Submitted for build testing.

If successful, I'll follow-up with a PR.

Great, thanks a lot.

Alex

maintainer
#16 lore raw

[GIT PULL] Immutable branch between MFD, Pinctrl and Regulator due for the v6.10 merge window

In reply to Alex Bee

Enjoy!

The following changes since commit 4cece764965020c22cff7665b18a012006359095:

Linux 6.9-rc1 (2024-03-24 14:10:05 -0700)

are available in the Git repository at:

git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git ib-mfd-pinctrl-regulator-v6.10

for you to fetch changes up to 5eb068da74a0b443fb99a89d9e5062691649c470:

regulator: rk808: Add RK816 support (2024-05-03 09:15:38 +0100)

----------------------------------------------------------------
Immutable branch between MFD, Pinctrl and Regulator due for the v6.10 merge window

----------------------------------------------------------------
Alex Bee (5):
dt-bindings: mfd: Add rk816 binding
mfd: rk8xx: Add RK816 support
pinctrl: rk805: Add rk816 pinctrl support
regulator: rk808: Support apply_bit for rk808_set_suspend_voltage_range
regulator: rk808: Add RK816 support

 .../devicetree/bindings/mfd/rockchip,rk816.yaml    | 274 +++++++++++++++++++++
 drivers/mfd/Kconfig                                |   4 +-
 drivers/mfd/rk8xx-core.c                           | 104 ++++++++
 drivers/mfd/rk8xx-i2c.c                            |  45 +++-
 drivers/pinctrl/pinctrl-rk805.c                    |  69 ++++++
 drivers/regulator/rk808-regulator.c                | 218 +++++++++++++++-
 include/linux/mfd/rk808.h                          | 144 +++++++++++
 7 files changed, 851 insertions(+), 7 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mfd/rockchip,rk816.yaml
Signature · 1 line
Lee Jones [李琼斯]