hwmon: (amc6821) Various improvements
Subsystems (2)
Guenter Roeck
maintainerv2 cover hwmon: (amc6821) Various improvements
Cleanup and modernize the amc2821 driver.
Summary of changes:
- Stop accepting invalid pwm values.
- Improve consistency of reading vs. writing fan speed limits
- Rename fan1_div to fan1_pulses
- Add support for fan1_target and pwm1_enable mode 4
- Reorder include files, drop unnecessary ones
- Use tabs for column alignment in defines
- Use BIT() and GENMASK()
- Drop unnecessary enum chips
- Convert to use regmap
- Convert to with_info API
- Add support for pwm1_mode attribute
v2:
- Use kstrtou8() instead of kstrtol() where possible
- Limit range of pwm1_auto_point_pwm to 0..254 in patch 1 instead of limiting it later, and do not accept invalid values for the attribute
- Do not accept negative fan speed values
- Display fan speed and speed limit as 0 if register value is 0 (instead of 6000000), as in original code
- Only permit writing 0 (unlimited) for the maximum fan speed
- Add Reviewed-by: tags where given
- Fix definition of AMC6821_CONF1_FDRC1 in patch 7/10
- Use sign_extend32() instead of odd type cast
- Drop remaining spurious debug message in patch 9 instead of patch 10
- Add missing "select REGMAP_I2C" to Kconfig
- Change misleading variable name from 'mask' to 'mode'
- Use sysfs_emit instead of sprintf everywhere
- Add support for pwm1_mode attribute
----------------------------------------------------------------
Guenter Roeck (11):
hwmon: (amc6821) Stop accepting invalid pwm values
hwmon: (amc6821) Make reading and writing fan speed limits consistent
hwmon: (amc6821) Rename fan1_div to fan1_pulses
hwmon: (amc6821) Add support for fan1_target and pwm1_enable mode 4
hwmon: (amc2821) Reorder include files, drop unnecessary ones
hwmon: (amc6821) Use tabs for column alignment in defines
hwmon: (amc2821) Use BIT() and GENMASK()
hwmon: (amc6821) Drop unnecessary enum chips
hwmon: (amc6821) Convert to use regmap
hwmon: (amc6821) Convert to with_info API
hwmon: (amc6821) Add support for pwm1_mode attribute
Documentation/hwmon/amc6821.rst | 7 +- drivers/hwmon/Kconfig | 1 + drivers/hwmon/amc6821.c | 1299 ++++++++++++++++++++------------------- 3 files changed, 660 insertions(+), 647 deletions(-)
Guenter Roeck
maintainerPATCH v2 1/11 hwmon: (amc6821) Stop accepting invalid pwm values
The pwm value range is well defined from 0..255. Don't accept any values outside this range.
---
v2: Use kstrtou8() instead of kstrtol() where possible.
Limit range of pwm1_auto_point_pwm to 0..254 in patch 1 instead of limiting it later, and do not accept invalid values for the attribute.
drivers/hwmon/amc6821.c | 15 +++++++++------ 1 file changed, 9 insertions(+), 6 deletions(-)
drivers/hwmon/amc6821.c +9 -6
@@ -355,13 +355,13 @@ static ssize_t pwm1_store(struct device *dev, {struct amc6821_data *data =dev_get_drvdata (dev);struct i2c_client *client = data->client; -long val; -int ret =kstrtol (buf,10 , &val); +u8 val; +int ret =kstrtou8 (buf,10 , &val);if (ret)return ret;mutex_lock (&data->update_lock); - data->pwm1 =clamp_val (val ,0 ,255 ); + data->pwm1 = val;i2c_smbus_write_byte_data (client,AMC6821_REG_DCY , data->pwm1);mutex_unlock (&data->update_lock);return count;
@@ -558,13 +558,16 @@ static ssize_t pwm1_auto_point_pwm_store(struct device *dev,struct amc6821_data *data =dev_get_drvdata (dev);struct i2c_client *client = data->client;int dpwm; -long val; -int ret =kstrtol (buf,10 , &val); +u8 val; +int ret =kstrtou8 (buf,10 , &val);if (ret)return ret; +if (val >254 ) +return -EINVAL ; +mutex_lock (&data->update_lock); - data->pwm1_auto_point_pwm[1 ] =clamp_val (val,0 ,254 ); + data->pwm1_auto_point_pwm[1 ] = val;if (i2c_smbus_write_byte_data (client,AMC6821_REG_DCY_LOW_TEMP , data->pwm1_auto_point_pwm[1 ])) {dev_err (&client->dev,"Register write error, aborting.\n" );
Signature · 1 line
2.39.2
Re: [PATCH v2 01/11] hwmon: (amc6821) Stop accepting invalid pwm values
Hi Guenter,
Quoted 36 lines · Guenter Roeck
The pwm value range is well defined from 0..255. Don't accept any values outside this range.
Signed-off-by Guenter Roeck <[email protected]>---
v2: Usekstrtou8()instead ofkstrtol()where possible.
Limit range ofpwm1_auto_point_pwmto 0..254 in patch 1 instead of limiting it later, and do not accept invalid values for the attribute.drivers/hwmon/amc6821.c | 15 +++++++++------ 1 file changed, 9 insertions(+), 6 deletions(-)drivers/hwmon/amc6821.c +3
-3@@ -355,13 +355,13 @@ static ssize_t pwm1_store(struct device *dev, {struct amc6821_data *data =dev_get_drvdata (dev);struct i2c_client *client = data->client; -long val; -int ret =kstrtol (buf,10 , &val); +u8 val; +int ret =kstrtou8 (buf,10 , &val);if (ret)return ret;mutex_lock (&data->update_lock); - data->pwm1 =clamp_val (val ,0 ,255 ); + data->pwm1 = val;i2c_smbus_write_byte_data (client,AMC6821_REG_DCY , data->pwm1);mutex_unlock (&data->update_lock);return count;@@ -558,13 +558,16 @@ static ssize_t pwm1_auto_point_pwm_store(struct device *dev,struct amc6821_data *data =dev_get_drvdata (dev);
drivers/hwmon/amc6821.c static ssize_t pwm1_auto_point_pwm_store(struct device *dev, · line 566
Quoted 10 lines
drivers/hwmon/amc6821.c +3
-2struct i2c_client *client = data->client;int dpwm; -long val; -int ret =kstrtol (buf,10 , &val); +u8 val; +int ret =kstrtou8 (buf,10 , &val);if (ret)return ret; +if (val >254 )
Would have appreciated a comment as to why it's 254. My understanding is that the subsystem requires no overlap between multiple pwm_auto_points? 0 being 0 and 2 being 255, we need 1 to be 255?
Actually, that doesn't explain why we allow 0 here, so maybe I'm just clueless :)
The change itself though:
Thanks!
Quentin
Guenter Roeck
maintainerRe: [PATCH v2 01/11] hwmon: (amc6821) Stop accepting invalid pwm values
Quoted 47 lines · Quentin Schulz
Hi Guenter,
Quoted 44 lines · Guenter Roeck
The pwm value range is well defined from 0..255. Don't accept any values outside this range.
Signed-off-by Guenter Roeck <[email protected]>---
v2: Usekstrtou8()instead ofkstrtol()where possible. Limit range ofpwm1_auto_point_pwmto 0..254 in patch 1 instead of limiting it later, and do not accept invalid values for the attribute.
drivers/hwmon/amc6821.c| 15 +++++++++------1 file changed, 9 insertions(+), 6 deletions(-)drivers/hwmon/amc6821.c +5
-5@@ -355,13 +355,13 @@ static ssize_t pwm1_store(struct device *dev, { struct amc6821_data *data = dev_get_drvdata(dev); struct i2c_client *client = data->client; - long val; - int ret = kstrtol(buf, 10, &val); + u8 val; + int ret = kstrtou8(buf, 10, &val); if (ret) return ret; mutex_lock(&data->update_lock); - data->pwm1 = clamp_val(val , 0, 255); + data->pwm1 = val; i2c_smbus_write_byte_data(client, AMC6821_REG_DCY, data->pwm1); mutex_unlock(&data->update_lock); return count;@@ -558,13 +558,16 @@ static ssize_t pwm1_auto_point_pwm_store(struct device *dev, struct amc6821_data *data = dev_get_drvdata(dev); struct i2c_client *client = data->client; int dpwm; - long val; - int ret = kstrtol(buf, 10, &val); + u8 val; + int ret = kstrtou8(buf, 10, &val); if (ret) return ret;
Quoted 4 lines
drivers/hwmon/amc6821.c static ssize_t pwm1_auto_point_pwm_store(struct device *dev, · line 566
Quoted 1 line
drivers/hwmon/amc6821.c +1
-0+ if (val > 254)Would have appreciated a comment as to why it's 254. My understanding is that the subsystem requires no overlap between multiple
pwm_auto_points? 0 being 0 and 2 being 255, we need 1 to be 255?
No idea, really, I just took it from the original code. I don't find a hint in the code suggesting why 255 would be worse than 0.
Quoted 2 lines
Actually, that doesn't explain why we allow 0 here, so maybe I'm just clueless :)
Yes, agreed, that doesn't really make sense. I'll change the upper limit to 255.
Quoted 3 lines
The change itself though:
Reviewed-by Quentin Schulz <[email protected]>
... but I'll also keep that tag unless you start screaming.
Thanks,
Guenter
Guenter Roeck
maintainerPATCH v2 2/11 hwmon: (amc6821) Make reading and writing fan speed limits consistent
In reply to Guenter RoeckThe default value of the maximum fan speed limit register is 0, essentially translating to an unlimited fan speed. When reading the limit, a value of 0 is reported in this case. However, writing a value of 0 results in writing a value of 0xffff into the register, which is inconsistent.
To solve the problem, permit writing a limit of 0 for the maximim fan speed, effectively translating to "no limit". Write 0 into the register if a limit value of 0 is written. Otherwise limit the range to <1..6000000> and write 1..0xffff into the register. This ensures that reading and writing from and to a limit register return the same value while at the same time not changing reported values when reading the speed or limits.
While at it, restrict fan limit writes to non-negative numbers; writing a negative limit does not make sense and should be reported instead of being corrected.
---
v2: Do not accept negative fan speed values
Display fan speed and speed limit as 0 if register value is 0 (instead of 6000000), as in original code.
Only permit writing 0 (unlimited) for the maximum fan speed.
drivers/hwmon/amc6821.c | 13 +++++++++---- 1 file changed, 9 insertions(+), 4 deletions(-)
drivers/hwmon/amc6821.c +9 -4
@@ -617,15 +617,20 @@ static ssize_t fan_store(struct device *dev, struct device_attribute *attr, {struct amc6821_data *data =dev_get_drvdata (dev);struct i2c_client *client = data->client; -long val; +unsigned long val;int ix =to_sensor_dev_attr (attr)->index; -int ret =kstrtol (buf,10 , &val); +int ret =kstrtoul (buf,10 , &val);if (ret)return ret; - val =1 > val ?0xFFFF :6000000 /val; + +/* The minimum fan speed must not be unlimited (0) */ +if (ix ==IDX_FAN1_MIN && !val) +return -EINVAL ; + + val = val >0 ?6000000 /clamp_val (val,1 ,6000000 ) :0 ;mutex_lock (&data->update_lock); - data->fan[ix] = (u16 )clamp_val (val,1 ,0xFFFF ); + data->fan[ix] =clamp_val (val,0 ,0xFFFF );if (i2c_smbus_write_byte_data (client, fan_reg_low[ix], data->fan[ix] &0xFF )) {dev_err (&client->dev,"Register write error, aborting.\n" );
Signature · 1 line
2.39.2
Re: [PATCH v2 02/11] hwmon: (amc6821) Make reading and writing fan speed limits consistent
Hi Guenter,
Quoted 41 lines · Guenter Roeck
The default value of the maximum fan speed limit register is 0, essentially translating to an unlimited fan speed. When reading the limit, a value of 0 is reported in this case. However, writing a value of 0 results in writing a value of
0xffffinto the register, which is inconsistent.To solve the problem, permit writing a limit of 0 for the maximim fan speed, effectively translating to "no limit". Write 0 into the register if a limit value of 0 is written. Otherwise limit the range to <1..6000000> and write 1..0xffff into the register. This ensures that reading and writing from and to a limit register return the same value while at the same time not changing reported values when reading the speed or limits.
While at it, restrict fan limit writes to non-negative numbers; writing a negative limit does not make sense and should be reported instead of being corrected.
Signed-off-by Guenter Roeck <[email protected]>---
v2: Do not accept negative fan speed values
Display fan speed and speed limit as 0 if register value is 0 (instead of 6000000), as in original code.
Only permit writing 0 (unlimited) for the maximum fan speed.drivers/hwmon/amc6821.c | 13 +++++++++---- 1 file changed, 9 insertions(+), 4 deletions(-)drivers/hwmon/amc6821.c +2
-2@@ -617,15 +617,20 @@ static ssize_t fan_store(struct device *dev, struct device_attribute *attr, {struct amc6821_data *data =dev_get_drvdata (dev);struct i2c_client *client = data->client; -long val; +unsigned long val;int ix =to_sensor_dev_attr (attr)->index; -int ret =kstrtol (buf,10 , &val); +int ret =kstrtoul (buf,10 , &val);
drivers/hwmon/amc6821.c static ssize_t fan_store(struct device *dev, struct device_attribute *attr, · line 631
Quoted 10 lines
drivers/hwmon/amc6821.c +6
-1if (ret)return ret; - val =1 > val ?0xFFFF :6000000 /val; + +/* The minimum fan speed must not be unlimited (0) */ +if (ix ==IDX_FAN1_MIN && !val) +return -EINVAL ; + + val = val >0 ?6000000 /clamp_val (val,1 ,6000000 ) :0 ;
I'm wondering if we shouldn't check !val for min after this line instead? Otherwise we allow 6000001+RPM speeds... which is technically unlimited.
Nitpicking though, therefore:
Thanks!
Quentin
Guenter Roeck
maintainerRe: [PATCH v2 02/11] hwmon: (amc6821) Make reading and writing fan speed limits consistent
Quoted 47 lines · Quentin Schulz
Hi Guenter,
Quoted 44 lines · Guenter Roeck
The default value of the maximum fan speed limit register is 0, essentially translating to an unlimited fan speed. When reading the limit, a value of 0 is reported in this case. However, writing a value of 0 results in writing a value of
0xffffinto the register, which is inconsistent.To solve the problem, permit writing a limit of 0 for the maximim fan speed, effectively translating to "no limit". Write 0 into the register if a limit value of 0 is written. Otherwise limit the range to <1..6000000> and write 1..0xffff into the register. This ensures that reading and writing from and to a limit register return the same value while at the same time not changing reported values when reading the speed or limits.
While at it, restrict fan limit writes to non-negative numbers; writing a negative limit does not make sense and should be reported instead of being corrected.
Signed-off-by Guenter Roeck <[email protected]>---
v2: Do not accept negative fan speed values
Display fan speed and speed limit as 0 if register value is 0 (instead of 6000000), as in original code.
Only permit writing 0 (unlimited) for the maximum fan speed.
drivers/hwmon/amc6821.c| 13 +++++++++----1 file changed, 9 insertions(+), 4 deletions(-)drivers/hwmon/amc6821.c +2
-3@@ -617,15 +617,20 @@ static ssize_t fan_store(struct device *dev, struct device_attribute *attr, { struct amc6821_data *data = dev_get_drvdata(dev); struct i2c_client *client = data->client; - long val; + unsigned long val; int ix = to_sensor_dev_attr(attr)->index; - int ret = kstrtol(buf, 10, &val); + int ret = kstrtoul(buf, 10, &val); if (ret) return ret; - val = 1 > val ? 0xFFFF : 6000000/val;
Quoted 9 lines
drivers/hwmon/amc6821.c static ssize_t fan_store(struct device *dev, struct device_attribute *attr, · line 630
Quoted 6 lines
drivers/hwmon/amc6821.c +6
-0+ + /* The minimum fan speed must not be unlimited (0) */ + if (ix == IDX_FAN1_MIN && !val) + return -EINVAL; + + val = val > 0 ? 6000000 / clamp_val(val, 1, 6000000) : 0;I'm wondering if we shouldn't check !val for min after this line instead? Otherwise we allow 6000001+RPM speeds... which is technically unlimited.
If ix == IDX_FAN1_MIN, val must be positive because of the check above. The expression "6000000 / clamp_val(val, 1, 6000000)" is therefore always positive as well because val is clamped. Its minimum result would be 6000000/6000000 = 1. The alternate case of the ternary expression would never hit because it is guaranteed that val > 0. Am I missing something ?
Thanks,
Guenter
Re: [PATCH v2 02/11] hwmon: (amc6821) Make reading and writing fan speed limits consistent
Hi Guenter,
Quoted 59 lines · Guenter Roeck
Quoted 48 lines · Quentin Schulz
Hi Guenter,
Quoted 45 lines · Guenter Roeck
The default value of the maximum fan speed limit register is 0, essentially translating to an unlimited fan speed. When reading the limit, a value of 0 is reported in this case. However, writing a value of 0 results in writing a value of
0xffffinto the register, which is inconsistent.To solve the problem, permit writing a limit of 0 for the maximim fan speed, effectively translating to "no limit". Write 0 into the register if a limit value of 0 is written. Otherwise limit the range to <1..6000000> and write 1..0xffff into the register. This ensures that reading and writing from and to a limit register return the same value while at the same time not changing reported values when reading the speed or limits.
While at it, restrict fan limit writes to non-negative numbers; writing a negative limit does not make sense and should be reported instead of being corrected.
Signed-off-by Guenter Roeck <[email protected]>---
v2: Do not accept negative fan speed values
Display fan speed and speed limit as 0 if register value is 0 (instead of 6000000), as in original code.
Only permit writing 0 (unlimited) for the maximum fan speed.
drivers/hwmon/amc6821.c| 13 +++++++++----1 file changed, 9 insertions(+), 4 deletions(-)drivers/hwmon/amc6821.c +2
-3@@ -617,15 +617,20 @@ static ssize_t fan_store(struct device *dev, struct device_attribute *attr, { struct amc6821_data *data = dev_get_drvdata(dev); struct i2c_client *client = data->client; - long val; + unsigned long val; int ix = to_sensor_dev_attr(attr)->index; - int ret = kstrtol(buf, 10, &val); + int ret = kstrtoul(buf, 10, &val); if (ret) return ret; - val = 1 > val ? 0xFFFF : 6000000/val;Quoted 9 lines
drivers/hwmon/amc6821.c static ssize_t fan_store(struct device *dev, struct device_attribute *attr, · line 630
Quoted 6 lines
drivers/hwmon/amc6821.c +6
-0+ + /* The minimum fan speed must not be unlimited (0) */ + if (ix == IDX_FAN1_MIN && !val) + return -EINVAL; + + val = val > 0 ? 6000000 / clamp_val(val, 1, 6000000) : 0;I'm wondering if we shouldn't check !val for min after this line instead? Otherwise we allow 6000001+RPM speeds... which is technically unlimited.
Quoted 6 lines
If ix ==
IDX_FAN1_MIN, val must be positive because of the check above. The expression "6000000 /clamp_val(val, 1, 6000000)" is therefore always positive as well because val is clamped. Its minimum result would be 6000000/6000000 = 1. The alternate case of the ternary expression would never hit because it is guaranteed that val > 0. Am I missing something ?
No, I misread the code and I didn't see the clamp_val, which means we cannot have the denominator be > 6000000, meaning val cannot be 0 after that line (well, except if it is 0 **before** already).
So no, just brain fart.
Also, we probably could swap clamp_val(val, 1, 6000000) for min(val, 6000000) as val > 0 because of the ternary operator condition. But that's nothing important nor interesting.
Cheers,
Quentin
Guenter Roeck
maintainerRe: [PATCH v2 02/11] hwmon: (amc6821) Make reading and writing fan speed limits consistent
Quoted 68 lines · Quentin Schulz
Hi Guenter,
Quoted 58 lines · Guenter Roeck
Quoted 47 lines · Quentin Schulz
Hi Guenter,
Quoted 44 lines · Guenter Roeck
The default value of the maximum fan speed limit register is 0, essentially translating to an unlimited fan speed. When reading the limit, a value of 0 is reported in this case. However, writing a value of 0 results in writing a value of
0xffffinto the register, which is inconsistent.To solve the problem, permit writing a limit of 0 for the maximim fan speed, effectively translating to "no limit". Write 0 into the register if a limit value of 0 is written. Otherwise limit the range to <1..6000000> and write 1..0xffff into the register. This ensures that reading and writing from and to a limit register return the same value while at the same time not changing reported values when reading the speed or limits.
While at it, restrict fan limit writes to non-negative numbers; writing a negative limit does not make sense and should be reported instead of being corrected.
Signed-off-by Guenter Roeck <[email protected]>---
v2: Do not accept negative fan speed values
Display fan speed and speed limit as 0 if register value is 0 (instead of 6000000), as in original code.
Only permit writing 0 (unlimited) for the maximum fan speed.
drivers/hwmon/amc6821.c| 13 +++++++++----1 file changed, 9 insertions(+), 4 deletions(-)drivers/hwmon/amc6821.c +2
-3@@ -617,15 +617,20 @@ static ssize_t fan_store(struct device *dev, struct device_attribute *attr, { struct amc6821_data *data = dev_get_drvdata(dev); struct i2c_client *client = data->client; - long val; + unsigned long val; int ix = to_sensor_dev_attr(attr)->index; - int ret = kstrtol(buf, 10, &val); + int ret = kstrtoul(buf, 10, &val); if (ret) return ret; - val = 1 > val ? 0xFFFF : 6000000/val;Quoted 9 lines
drivers/hwmon/amc6821.c static ssize_t fan_store(struct device *dev, struct device_attribute *attr, · line 630
Quoted 6 lines
drivers/hwmon/amc6821.c +6
-0+ + /* The minimum fan speed must not be unlimited (0) */ + if (ix == IDX_FAN1_MIN && !val) + return -EINVAL; + + val = val > 0 ? 6000000 / clamp_val(val, 1, 6000000) : 0;I'm wondering if we shouldn't check !val for min after this line instead? Otherwise we allow 6000001+RPM speeds... which is technically unlimited.
Quoted 6 lines
If ix ==
IDX_FAN1_MIN, val must be positive because of the check above. The expression "6000000 /clamp_val(val, 1, 6000000)" is therefore always positive as well because val is clamped. Its minimum result would be 6000000/6000000 = 1. The alternate case of the ternary expression would never hit because it is guaranteed that val > 0. Am I missing something ?
Quoted 6 lines
No, I misread the code and I didn't see the
clamp_val, which means we cannot have the denominator be > 6000000, meaning val cannot be 0 after that line (well, except if it is 0 **before** already).So no, just brain fart.
Also, we probably could swap
clamp_val(val, 1, 6000000)formin(val, 6000000)as val > 0 because of the ternary operator condition. But that's nothing important nor interesting.
Good point. I may do that if I have to send v4 (if I remember), but for now the existing code should be good enough.
Thanks,
Guenter
Guenter Roeck
maintainerPATCH v2 3/11 hwmon: (amc6821) Rename fan1_div to fan1_pulses
In reply to Guenter RoeckThe chip does not have a fan divisor. What it does have is a configuration to set either 2 or 4 pulses per fan rotation. Rename the attribute to reflect its use. Update documentation accordingly.
---
v2: Add Quentin's Reviewed-by: tag
Documentation/hwmon/amc6821.rst | 2 +- drivers/hwmon/amc6821.c | 26 +++++++++++++------------- 2 files changed, 14 insertions(+), 14 deletions(-)
Documentation/hwmon/amc6821.rst +1 -1
@@ -47,7 +47,7 @@ fan1_input ro tachometer speed fan1_min rw " fan1_max rw " fan1_fault ro " -fan1_div rw Fan divisor can be either 2 or 4. +fan1_pulses rw Pulses per revolution can be either 2 or 4. pwm1 rw pwm1 pwm1_enable rw regulator mode, 1=open loop, 2=fan controlled
drivers/hwmon/amc6821.c +13 -13
@@ -148,7 +148,7 @@ struct amc6821_data {int temp[TEMP_IDX_LEN ];u16 fan[FAN1_IDX_LEN ]; -u8 fan1_div; +u8 fan1_pulses;u8 pwm1;u8 temp1_auto_point_temp[3 ];
@@ -193,9 +193,9 @@ static struct amc6821_data *amc6821_update_device(struct device *dev) client, fan_reg_hi[i]) << 8; } - data->fan1_div =i2c_smbus_read_byte_data (client, + data->fan1_pulses =i2c_smbus_read_byte_data (client,AMC6821_REG_CONF4 ); - data->fan1_div = data->fan1_div &AMC6821_CONF4_PSPR ?4 :2 ; + data->fan1_pulses = data->fan1_pulses &AMC6821_CONF4_PSPR ?4 :2 ; data->pwm1_auto_point_pwm[0 ] =0 ; data->pwm1_auto_point_pwm[2 ] =255 ;
@@ -647,16 +647,16 @@ static ssize_t fan_store(struct device *dev, struct device_attribute *attr,return count; } -static ssize_t fan1_div_show (struct device *dev, -struct device_attribute *devattr,char *buf) +static ssize_t fan1_pulses_show (struct device *dev, +struct device_attribute *devattr,char *buf) {struct amc6821_data *data =amc6821_update_device (dev); -return sprintf (buf,"%d\n" , data->fan1_div); +return sprintf (buf,"%d\n" , data->fan1_pulses); } -static ssize_t fan1_div_store (struct device *dev, -struct device_attribute *attr,const char *buf, -size_t count) +static ssize_t fan1_pulses_store (struct device *dev, +struct device_attribute *attr,const char *buf, +size_t count) {struct amc6821_data *data =dev_get_drvdata (dev);struct i2c_client *client = data->client;
@@ -676,11 +676,11 @@ static ssize_t fan1_div_store(struct device *dev,switch (val) {case 2 : config &= ~AMC6821_CONF4_PSPR ; - data->fan1_div =2 ; + data->fan1_pulses =2 ;break ;case 4 : config |=AMC6821_CONF4_PSPR ; - data->fan1_div =4 ; + data->fan1_pulses =4 ;break ;default : count = -EINVAL ;
@@ -715,7 +715,7 @@ static SENSOR_DEVICE_ATTR_RO(fan1_input, fan, IDX_FAN1_INPUT); static SENSOR_DEVICE_ATTR_RW(fan1_min, fan, IDX_FAN1_MIN); static SENSOR_DEVICE_ATTR_RW(fan1_max, fan, IDX_FAN1_MAX); static SENSOR_DEVICE_ATTR_RO(fan1_fault, fan1_fault, 0); -static SENSOR_DEVICE_ATTR_RW(fan1_div, fan1_div, 0); +static SENSOR_DEVICE_ATTR_RW(fan1_pulses, fan1_pulses, 0); static SENSOR_DEVICE_ATTR_RW(pwm1, pwm1, 0); static SENSOR_DEVICE_ATTR_RW(pwm1_enable, pwm1_enable, 0);
@@ -758,7 +758,7 @@ static struct attribute *amc6821_attrs[] = { &sensor_dev_attr_fan1_min.dev_attr.attr, &sensor_dev_attr_fan1_max.dev_attr.attr, &sensor_dev_attr_fan1_fault.dev_attr.attr, - &sensor_dev_attr_fan1_div.dev_attr.attr, + &sensor_dev_attr_fan1_pulses.dev_attr.attr, &sensor_dev_attr_pwm1.dev_attr.attr, &sensor_dev_attr_pwm1_enable.dev_attr.attr, &sensor_dev_attr_pwm1_auto_channels_temp.dev_attr.attr,
Signature · 1 line
2.39.2
Guenter Roeck
maintainerPATCH v2 4/11 hwmon: (amc6821) Add support for fan1_target and pwm1_enable mode 4
In reply to Guenter RoeckAfter setting fan1_target and setting pwm1_enable to 4, the fan controller tries to achieve the requested fan speed.
---
v2: Do not permit writing negative or unlimited target fan speed
Documentation/hwmon/amc6821.rst | 4 ++++ drivers/hwmon/amc6821.c | 25 +++++++++++++++++-------- 2 files changed, 21 insertions(+), 8 deletions(-)
Documentation/hwmon/amc6821.rst +4 -0
@@ -48,12 +48,16 @@ fan1_min rw " fan1_max rw " fan1_fault ro " fan1_pulses rw Pulses per revolution can be either 2 or 4. +fan1_target rw Target fan speed, to be used with pwm1_enable + mode 4. pwm1 rw pwm1 pwm1_enable rw regulator mode, 1=open loop, 2=fan controlled by remote temperature, 3=fan controlled by combination of the on-chip temperature and remote-sensor temperature, + 4=fan controlled by target rpm set with + fan1_target attribute. pwm1_auto_channels_temp ro 1 if pwm_enable==2, 3 if pwm_enable==3 pwm1_auto_point1_pwm ro Hardwired to 0, shared for both temperature channels.
drivers/hwmon/amc6821.c +17 -8
@@ -66,6 +66,8 @@ enum chips { amc6821 };#define AMC6821_REG_TACH_LLIMITH 0x11#define AMC6821_REG_TACH_HLIMITL 0x12#define AMC6821_REG_TACH_HLIMITH 0x13 +#define AMC6821_REG_TACH_SETTINGL 0x1e +#define AMC6821_REG_TACH_SETTINGH 0x1f#define AMC6821_CONF1_START 0x01#define AMC6821_CONF1_FAN_INT_EN 0x02
@@ -122,17 +124,18 @@ static const u8 temp_reg[] = {AMC6821_REG_LTEMP_HI,AMC6821_REG_RTEMP_LIMIT_MAX , AMC6821_REG_RTEMP_CRIT, }; -enum {IDX_FAN1_INPUT =0 ,IDX_FAN1_MIN ,IDX_FAN1_MAX , +enum {IDX_FAN1_INPUT =0 ,IDX_FAN1_MIN ,IDX_FAN1_MAX ,IDX_FAN1_TARGET ,FAN1_IDX_LEN , };static const u8 fan_reg_low[] = {AMC6821_REG_TDATA_LOW ,AMC6821_REG_TACH_LLIMITL , -AMC6821_REG_TACH_HLIMITL , }; - +AMC6821_REG_TACH_HLIMITL , +AMC6821_REG_TACH_SETTINGL , };static const u8 fan_reg_hi[] = {AMC6821_REG_TDATA_HI ,AMC6821_REG_TACH_LLIMITH , -AMC6821_REG_TACH_HLIMITH , }; +AMC6821_REG_TACH_HLIMITH , +AMC6821_REG_TACH_SETTINGH , };/* * Client data (each client gets its own)
@@ -250,10 +253,10 @@ static struct amc6821_data *amc6821_update_device(struct device *dev)break ;case 1 :/* * semi-open loop: software sets rpm, chip controls -* pwm1, currently not implemented +* pwm1 */ data->pwm1_auto_channels_temp =0 ; - data->pwm1_enable =0 ; + data->pwm1_enable =4 ;break ; }
@@ -407,6 +410,10 @@ static ssize_t pwm1_enable_store(struct device *dev, config |=AMC6821_CONF1_FDRC0 ; config |=AMC6821_CONF1_FDRC1 ;break ; +case 4 : + config |=AMC6821_CONF1_FDRC0 ; + config &= ~AMC6821_CONF1_FDRC1 ; +break ;default : count = -EINVAL ; goto unlock;
@@ -623,8 +630,8 @@ static ssize_t fan_store(struct device *dev, struct device_attribute *attr,if (ret)return ret; -/* The minimum fan speed must not be unlimited (0) */ -if (ix ==IDX_FAN1_MIN && !val) +/* Minimum and target fan speed must not be unlimited (0) */ +if ((ix ==IDX_FAN1_MIN || ix ==IDX_FAN1_TARGET ) && !val)return -EINVAL ; val = val >0 ?6000000 /clamp_val (val,1 ,6000000 ) :0 ;
@@ -714,6 +721,7 @@ static SENSOR_DEVICE_ATTR_RO(temp2_crit_alarm, temp_alarm, IDX_TEMP2_CRIT); static SENSOR_DEVICE_ATTR_RO(fan1_input, fan, IDX_FAN1_INPUT); static SENSOR_DEVICE_ATTR_RW(fan1_min, fan, IDX_FAN1_MIN); static SENSOR_DEVICE_ATTR_RW(fan1_max, fan, IDX_FAN1_MAX); +static SENSOR_DEVICE_ATTR_RW(fan1_target, fan, IDX_FAN1_TARGET); static SENSOR_DEVICE_ATTR_RO(fan1_fault, fan1_fault, 0); static SENSOR_DEVICE_ATTR_RW(fan1_pulses, fan1_pulses, 0);
@@ -757,6 +765,7 @@ static struct attribute *amc6821_attrs[] = { &sensor_dev_attr_fan1_input.dev_attr.attr, &sensor_dev_attr_fan1_min.dev_attr.attr, &sensor_dev_attr_fan1_max.dev_attr.attr, + &sensor_dev_attr_fan1_target.dev_attr.attr, &sensor_dev_attr_fan1_fault.dev_attr.attr, &sensor_dev_attr_fan1_pulses.dev_attr.attr, &sensor_dev_attr_pwm1.dev_attr.attr,
Signature · 1 line
2.39.2
Re: [PATCH v2 04/11] hwmon: (amc6821) Add support for fan1_target and pwm1_enable mode 4
Hi Guenter,
Quoted 4 lines · Guenter Roeck
After setting
fan1_targetand settingpwm1_enableto 4, the fan controller tries to achieve the requested fan speed.Signed-off-by Guenter Roeck <[email protected]>
Thanks!
Quentin
Guenter Roeck
maintainerPATCH v2 5/11 hwmon: (amc2821) Reorder include files, drop unnecessary ones
In reply to Guenter RoeckReorder include files to alphabetic order to simplify maintenance, and drop the unnecessary kernel.h include.
No functional change intended.
---
v2: Add Quentin's Reviewed-by: tag
drivers/hwmon/amc6821.c | 13 ++++++------- 1 file changed, 6 insertions(+), 7 deletions(-)
drivers/hwmon/amc6821.c +6 -7
@@ -8,16 +8,15 @@* Copyright (C) 2007 Hans J. Koch <[email protected]> */ -#include <linux/kernel.h> /* Needed for KERN_INFO */ -#include <linux/module.h> -#include <linux/init.h> -#include <linux/slab.h> -#include <linux/jiffies.h> -#include <linux/i2c.h> +#include <linux/err.h> #include <linux/hwmon.h> #include <linux/hwmon-sysfs.h> -#include <linux/err.h> +#include <linux/i2c.h> +#include <linux/init.h> +#include <linux/jiffies.h> +#include <linux/module.h> #include <linux/mutex.h> +#include <linux/slab.h> /* * Addresses to scan.
Signature · 1 line
2.39.2
Guenter Roeck
maintainerPATCH v2 6/11 hwmon: (amc6821) Use tabs for column alignment in defines
In reply to Guenter RoeckUsing tabs for column alignment makes the code easier to read.
No functional change intended.
---
v2: Add Quentin's Reviewed-by: tag
drivers/hwmon/amc6821.c | 128 ++++++++++++++++++++-------------------- 1 file changed, 64 insertions(+), 64 deletions(-)
drivers/hwmon/amc6821.c +64 -64
@@ -37,77 +37,77 @@ module_param(init, int, 0444);enum chips { amc6821 }; -#define AMC6821_REG_DEV_ID 0x3D -#define AMC6821_REG_COMP_ID 0x3E -#define AMC6821_REG_CONF1 0x00 -#define AMC6821_REG_CONF2 0x01 -#define AMC6821_REG_CONF3 0x3F -#define AMC6821_REG_CONF4 0x04 -#define AMC6821_REG_STAT1 0x02 -#define AMC6821_REG_STAT2 0x03 -#define AMC6821_REG_TDATA_LOW 0x08 -#define AMC6821_REG_TDATA_HI 0x09 -#define AMC6821_REG_LTEMP_HI 0x0A -#define AMC6821_REG_RTEMP_HI 0x0B -#define AMC6821_REG_LTEMP_LIMIT_MIN 0x15 -#define AMC6821_REG_LTEMP_LIMIT_MAX 0x14 -#define AMC6821_REG_RTEMP_LIMIT_MIN 0x19 -#define AMC6821_REG_RTEMP_LIMIT_MAX 0x18 -#define AMC6821_REG_LTEMP_CRIT 0x1B -#define AMC6821_REG_RTEMP_CRIT 0x1D -#define AMC6821_REG_PSV_TEMP 0x1C -#define AMC6821_REG_DCY 0x22 -#define AMC6821_REG_LTEMP_FAN_CTRL 0x24 -#define AMC6821_REG_RTEMP_FAN_CTRL 0x25 -#define AMC6821_REG_DCY_LOW_TEMP 0x21 +#define AMC6821_REG_DEV_ID 0x3D +#define AMC6821_REG_COMP_ID 0x3E +#define AMC6821_REG_CONF1 0x00 +#define AMC6821_REG_CONF2 0x01 +#define AMC6821_REG_CONF3 0x3F +#define AMC6821_REG_CONF4 0x04 +#define AMC6821_REG_STAT1 0x02 +#define AMC6821_REG_STAT2 0x03 +#define AMC6821_REG_TDATA_LOW 0x08 +#define AMC6821_REG_TDATA_HI 0x09 +#define AMC6821_REG_LTEMP_HI 0x0A +#define AMC6821_REG_RTEMP_HI 0x0B +#define AMC6821_REG_LTEMP_LIMIT_MIN 0x15 +#define AMC6821_REG_LTEMP_LIMIT_MAX 0x14 +#define AMC6821_REG_RTEMP_LIMIT_MIN 0x19 +#define AMC6821_REG_RTEMP_LIMIT_MAX 0x18 +#define AMC6821_REG_LTEMP_CRIT 0x1B +#define AMC6821_REG_RTEMP_CRIT 0x1D +#define AMC6821_REG_PSV_TEMP 0x1C +#define AMC6821_REG_DCY 0x22 +#define AMC6821_REG_LTEMP_FAN_CTRL 0x24 +#define AMC6821_REG_RTEMP_FAN_CTRL 0x25 +#define AMC6821_REG_DCY_LOW_TEMP 0x21 -#define AMC6821_REG_TACH_LLIMITL 0x10 -#define AMC6821_REG_TACH_LLIMITH 0x11 -#define AMC6821_REG_TACH_HLIMITL 0x12 -#define AMC6821_REG_TACH_HLIMITH 0x13 -#define AMC6821_REG_TACH_SETTINGL 0x1e -#define AMC6821_REG_TACH_SETTINGH 0x1f +#define AMC6821_REG_TACH_LLIMITL 0x10 +#define AMC6821_REG_TACH_LLIMITH 0x11 +#define AMC6821_REG_TACH_HLIMITL 0x12 +#define AMC6821_REG_TACH_HLIMITH 0x13 +#define AMC6821_REG_TACH_SETTINGL 0x1e +#define AMC6821_REG_TACH_SETTINGH 0x1f -#define AMC6821_CONF1_START 0x01 -#define AMC6821_CONF1_FAN_INT_EN 0x02 -#define AMC6821_CONF1_FANIE 0x04 -#define AMC6821_CONF1_PWMINV 0x08 -#define AMC6821_CONF1_FAN_FAULT_EN 0x10 -#define AMC6821_CONF1_FDRC0 0x20 -#define AMC6821_CONF1_FDRC1 0x40 -#define AMC6821_CONF1_THERMOVIE 0x80 +#define AMC6821_CONF1_START 0x01 +#define AMC6821_CONF1_FAN_INT_EN 0x02 +#define AMC6821_CONF1_FANIE 0x04 +#define AMC6821_CONF1_PWMINV 0x08 +#define AMC6821_CONF1_FAN_FAULT_EN 0x10 +#define AMC6821_CONF1_FDRC0 0x20 +#define AMC6821_CONF1_FDRC1 0x40 +#define AMC6821_CONF1_THERMOVIE 0x80 -#define AMC6821_CONF2_PWM_EN 0x01 -#define AMC6821_CONF2_TACH_MODE 0x02 -#define AMC6821_CONF2_TACH_EN 0x04 -#define AMC6821_CONF2_RTFIE 0x08 -#define AMC6821_CONF2_LTOIE 0x10 -#define AMC6821_CONF2_RTOIE 0x20 -#define AMC6821_CONF2_PSVIE 0x40 -#define AMC6821_CONF2_RST 0x80 +#define AMC6821_CONF2_PWM_EN 0x01 +#define AMC6821_CONF2_TACH_MODE 0x02 +#define AMC6821_CONF2_TACH_EN 0x04 +#define AMC6821_CONF2_RTFIE 0x08 +#define AMC6821_CONF2_LTOIE 0x10 +#define AMC6821_CONF2_RTOIE 0x20 +#define AMC6821_CONF2_PSVIE 0x40 +#define AMC6821_CONF2_RST 0x80 -#define AMC6821_CONF3_THERM_FAN_EN 0x80 -#define AMC6821_CONF3_REV_MASK 0x0F +#define AMC6821_CONF3_THERM_FAN_EN 0x80 +#define AMC6821_CONF3_REV_MASK 0x0F -#define AMC6821_CONF4_OVREN 0x10 -#define AMC6821_CONF4_TACH_FAST 0x20 -#define AMC6821_CONF4_PSPR 0x40 -#define AMC6821_CONF4_MODE 0x80 +#define AMC6821_CONF4_OVREN 0x10 +#define AMC6821_CONF4_TACH_FAST 0x20 +#define AMC6821_CONF4_PSPR 0x40 +#define AMC6821_CONF4_MODE 0x80 -#define AMC6821_STAT1_RPM_ALARM 0x01 -#define AMC6821_STAT1_FANS 0x02 -#define AMC6821_STAT1_RTH 0x04 -#define AMC6821_STAT1_RTL 0x08 -#define AMC6821_STAT1_R_THERM 0x10 -#define AMC6821_STAT1_RTF 0x20 -#define AMC6821_STAT1_LTH 0x40 -#define AMC6821_STAT1_LTL 0x80 +#define AMC6821_STAT1_RPM_ALARM 0x01 +#define AMC6821_STAT1_FANS 0x02 +#define AMC6821_STAT1_RTH 0x04 +#define AMC6821_STAT1_RTL 0x08 +#define AMC6821_STAT1_R_THERM 0x10 +#define AMC6821_STAT1_RTF 0x20 +#define AMC6821_STAT1_LTH 0x40 +#define AMC6821_STAT1_LTL 0x80 -#define AMC6821_STAT2_RTC 0x08 -#define AMC6821_STAT2_LTC 0x10 -#define AMC6821_STAT2_LPSV 0x20 -#define AMC6821_STAT2_L_THERM 0x40 -#define AMC6821_STAT2_THERM_IN 0x80 +#define AMC6821_STAT2_RTC 0x08 +#define AMC6821_STAT2_LTC 0x10 +#define AMC6821_STAT2_LPSV 0x20 +#define AMC6821_STAT2_L_THERM 0x40 +#define AMC6821_STAT2_THERM_IN 0x80enum {IDX_TEMP1_INPUT =0 ,IDX_TEMP1_MIN ,IDX_TEMP1_MAX ,IDX_TEMP1_CRIT ,IDX_TEMP2_INPUT ,IDX_TEMP2_MIN ,
Signature · 1 line
2.39.2
Guenter Roeck
maintainerPATCH v2 7/11 hwmon: (amc2821) Use BIT() and GENMASK()
In reply to Guenter RoeckUse BIT() and GENMASK() for bit and mask definitions to help distinguish bit and mask definitions from other defines and to make the code easier to read.
No functional change intended.
---
v2: Fix definition of AMC6821_CONF1_FDRC1 in this patch
drivers/hwmon/amc6821.c | 71 +++++++++++++++++++++-------------------- 1 file changed, 36 insertions(+), 35 deletions(-)
drivers/hwmon/amc6821.c +36 -35
@@ -8,6 +8,7 @@* Copyright (C) 2007 Hans J. Koch <[email protected]> */ +#include <linux/bits.h> #include <linux/err.h> #include <linux/hwmon.h> #include <linux/hwmon-sysfs.h>
@@ -68,46 +69,46 @@ enum chips { amc6821 };#define AMC6821_REG_TACH_SETTINGL 0x1e#define AMC6821_REG_TACH_SETTINGH 0x1f -#define AMC6821_CONF1_START 0x01 -#define AMC6821_CONF1_FAN_INT_EN 0x02 -#define AMC6821_CONF1_FANIE 0x04 -#define AMC6821_CONF1_PWMINV 0x08 -#define AMC6821_CONF1_FAN_FAULT_EN 0x10 -#define AMC6821_CONF1_FDRC0 0x20 -#define AMC6821_CONF1_FDRC1 0x40 -#define AMC6821_CONF1_THERMOVIE 0x80 +#define AMC6821_CONF1_START BIT(0) +#define AMC6821_CONF1_FAN_INT_EN BIT(1) +#define AMC6821_CONF1_FANIE BIT(2) +#define AMC6821_CONF1_PWMINV BIT(3) +#define AMC6821_CONF1_FAN_FAULT_EN BIT(4) +#define AMC6821_CONF1_FDRC0 BIT(5) +#define AMC6821_CONF1_FDRC1 BIT(6) +#define AMC6821_CONF1_THERMOVIE BIT(7) -#define AMC6821_CONF2_PWM_EN 0x01 -#define AMC6821_CONF2_TACH_MODE 0x02 -#define AMC6821_CONF2_TACH_EN 0x04 -#define AMC6821_CONF2_RTFIE 0x08 -#define AMC6821_CONF2_LTOIE 0x10 -#define AMC6821_CONF2_RTOIE 0x20 -#define AMC6821_CONF2_PSVIE 0x40 -#define AMC6821_CONF2_RST 0x80 +#define AMC6821_CONF2_PWM_EN BIT(0) +#define AMC6821_CONF2_TACH_MODE BIT(1) +#define AMC6821_CONF2_TACH_EN BIT(2) +#define AMC6821_CONF2_RTFIE BIT(3) +#define AMC6821_CONF2_LTOIE BIT(4) +#define AMC6821_CONF2_RTOIE BIT(5) +#define AMC6821_CONF2_PSVIE BIT(6) +#define AMC6821_CONF2_RST BIT(7) -#define AMC6821_CONF3_THERM_FAN_EN 0x80 -#define AMC6821_CONF3_REV_MASK 0x0F +#define AMC6821_CONF3_THERM_FAN_EN BIT(7) +#define AMC6821_CONF3_REV_MASK GENMASK(3, 0) -#define AMC6821_CONF4_OVREN 0x10 -#define AMC6821_CONF4_TACH_FAST 0x20 -#define AMC6821_CONF4_PSPR 0x40 -#define AMC6821_CONF4_MODE 0x80 +#define AMC6821_CONF4_OVREN BIT(4) +#define AMC6821_CONF4_TACH_FAST BIT(5) +#define AMC6821_CONF4_PSPR BIT(6) +#define AMC6821_CONF4_MODE BIT(7) -#define AMC6821_STAT1_RPM_ALARM 0x01 -#define AMC6821_STAT1_FANS 0x02 -#define AMC6821_STAT1_RTH 0x04 -#define AMC6821_STAT1_RTL 0x08 -#define AMC6821_STAT1_R_THERM 0x10 -#define AMC6821_STAT1_RTF 0x20 -#define AMC6821_STAT1_LTH 0x40 -#define AMC6821_STAT1_LTL 0x80 +#define AMC6821_STAT1_RPM_ALARM BIT(0) +#define AMC6821_STAT1_FANS BIT(1) +#define AMC6821_STAT1_RTH BIT(2) +#define AMC6821_STAT1_RTL BIT(3) +#define AMC6821_STAT1_R_THERM BIT(4) +#define AMC6821_STAT1_RTF BIT(5) +#define AMC6821_STAT1_LTH BIT(6) +#define AMC6821_STAT1_LTL BIT(7) -#define AMC6821_STAT2_RTC 0x08 -#define AMC6821_STAT2_LTC 0x10 -#define AMC6821_STAT2_LPSV 0x20 -#define AMC6821_STAT2_L_THERM 0x40 -#define AMC6821_STAT2_THERM_IN 0x80 +#define AMC6821_STAT2_RTC BIT(3) +#define AMC6821_STAT2_LTC BIT(4) +#define AMC6821_STAT2_LPSV BIT(5) +#define AMC6821_STAT2_L_THERM BIT(6) +#define AMC6821_STAT2_THERM_IN BIT(7)enum {IDX_TEMP1_INPUT =0 ,IDX_TEMP1_MIN ,IDX_TEMP1_MAX ,IDX_TEMP1_CRIT ,IDX_TEMP2_INPUT ,IDX_TEMP2_MIN ,
Signature · 1 line
2.39.2
Re: [PATCH v2 07/11] hwmon: (amc2821) Use BIT() and GENMASK()
Hi Guenter,
Quoted 7 lines · Guenter Roeck
Use
BIT()andGENMASK()for bit and mask definitions to help distinguish bit and mask definitions from other defines and to make the code easier to read.No functional change intended.
Signed-off-by Guenter Roeck <[email protected]>
Thanks!
Quentin
Guenter Roeck
maintainerPATCH v2 8/11 hwmon: (amc6821) Drop unnecessary enum chips
In reply to Guenter RoeckThe driver only supports a single chip, so an enum to determine the chip type is unnecessary. Drop it.
No functional change intended.
---
v2: Add Quentin's Reviewed-by: tag
drivers/hwmon/amc6821.c | 5 +---- 1 file changed, 1 insertion(+), 4 deletions(-)
drivers/hwmon/amc6821.c +1 -4
@@ -36,8 +36,6 @@ module_param(pwminv, int, 0444);static int init =1 ;/*Power-on initialization.*/ module_param (init, int,0444 ); -enum chips { amc6821 }; -#define AMC6821_REG_DEV_ID 0x3D#define AMC6821_REG_COMP_ID 0x3E#define AMC6821_REG_CONF1 0x00
@@ -945,7 +943,7 @@ static int amc6821_probe(struct i2c_client *client) }static const struct i2c_device_id amc6821_id[] = { - {"amc6821" , amc6821 }, + {"amc6821" ,0 }, { } };
@@ -954,7 +952,6 @@ MODULE_DEVICE_TABLE(i2c, amc6821_id);static const struct of_device_id __maybe_unused amc6821_of_match[] = { { .compatible ="ti,amc6821" , - .data = (void *)amc6821, }, { } };
Signature · 1 line
2.39.2
Guenter Roeck
maintainerPATCH v2 9/11 hwmon: (amc6821) Convert to use regmap
In reply to Guenter RoeckUse regmap for register accesses and for most caching.
While at it, use sysfs_emit() instead of sprintf() to write sysfs attribute data, and remove spurious debug messages which would only be seen as result of a bug in the code.
No functional change intended.
---
v2: Drop another spurious debug message in this patch instead of patch 10
Add missing "select REGMAP_I2C" to Kconfig
Change misleading variable name from 'mask' to 'mode'. Use sysfs_emit instead of sprintf everywhere
drivers/hwmon/Kconfig | 1 + drivers/hwmon/amc6821.c | 713 ++++++++++++++++++---------------------- 2 files changed, 329 insertions(+), 385 deletions(-)
drivers/hwmon/Kconfig +1 -0
@@ -2127,6 +2127,7 @@ config SENSORS_ADS7871 config SENSORS_AMC6821 tristate "Texas Instruments AMC6821" depends on I2C + select REGMAP_I2C help If you say yes here you get support for the Texas Instruments AMC6821 hardware monitoring chips.
drivers/hwmon/amc6821.c +328 -385
1,014 lines not on this page · raw message
Signature · 1 line
2.39.2
Re: [PATCH v2 09/11] hwmon: (amc6821) Convert to use regmap
Hi Guenter,
Quoted 114 lines · Guenter Roeck
Use regmap for register accesses and for most caching.
While at it, use
sysfs_emit()instead ofsprintf()to write sysfs attribute data, and remove spurious debug messages which would only be seen as result of a bug in the code.No functional change intended.
Signed-off-by Guenter Roeck <[email protected]>---
v2: Drop another spurious debug message in this patch instead of patch 10
Add missing "selectREGMAP_I2C" toKconfig
Change misleading variable name from 'mask' to 'mode'. Usesysfs_emitinstead of sprintf everywheredrivers/hwmon/Kconfig | 1 + drivers/hwmon/amc6821.c | 713 ++++++++++++++++++---------------------- 2 files changed, 329 insertions(+), 385 deletions(-)drivers/hwmon/Kconfig +1
-0@@ -2127,6 +2127,7 @@ config SENSORS_ADS7871 config SENSORS_AMC6821 tristate "Texas Instruments AMC6821" depends on I2C + select REGMAP_I2C help If you say yes here you get support for the Texas Instruments AMC6821 hardware monitoring chips.drivers/hwmon/amc6821.c +5
-27@@ -8,15 +8,16 @@* Copyright (C) 2007 Hans J. Koch <[email protected]> */ +#include <linux/bitops.h> #include <linux/bits.h> #include <linux/err.h> #include <linux/hwmon.h> #include <linux/hwmon-sysfs.h> #include <linux/i2c.h> #include <linux/init.h> -#include <linux/jiffies.h> #include <linux/module.h> #include <linux/mutex.h> +#include <linux/regmap.h> #include <linux/slab.h> /* @@ -44,6 +45,7 @@ module_param(init, int, 0444);#define AMC6821_REG_CONF4 0x04#define AMC6821_REG_STAT1 0x02#define AMC6821_REG_STAT2 0x03 +#define AMC6821_REG_TEMP_LO 0x06#define AMC6821_REG_TDATA_LOW 0x08#define AMC6821_REG_TDATA_HI 0x09#define AMC6821_REG_LTEMP_HI 0x0A@@ -61,11 +63,8 @@ module_param(init, int, 0444);#define AMC6821_REG_DCY_LOW_TEMP 0x21#define AMC6821_REG_TACH_LLIMITL 0x10 -#define AMC6821_REG_TACH_LLIMITH 0x11#define AMC6821_REG_TACH_HLIMITL 0x12 -#define AMC6821_REG_TACH_HLIMITH 0x13#define AMC6821_REG_TACH_SETTINGL 0x1e -#define AMC6821_REG_TACH_SETTINGH 0x1f#define AMC6821_CONF1_START BIT(0)#define AMC6821_CONF1_FAN_INT_EN BIT(1)@@ -130,224 +129,169 @@ static const u8 fan_reg_low[] = {AMC6821_REG_TDATA_LOW,AMC6821_REG_TACH_HLIMITL , AMC6821_REG_TACH_SETTINGL, }; -static const u8 fan_reg_hi[] = {AMC6821_REG_TDATA_HI , -AMC6821_REG_TACH_LLIMITH , -AMC6821_REG_TACH_HLIMITH , -AMC6821_REG_TACH_SETTINGH , }; -/* * Client data (each client gets its own) */ struct amc6821_data { -struct i2c_client *client; +struct regmap *regmap;struct mutex update_lock; -bool valid;/* false until following fields are valid */ -unsigned long last_updated;/* in jiffies */ -/* register values */ -int temp[TEMP_IDX_LEN ]; - -u16 fan[FAN1_IDX_LEN ]; -u8 fan1_pulses; - -u8 pwm1;u8 temp1_auto_point_temp[3 ];u8 temp2_auto_point_temp[3 ]; -u8 pwm1_auto_point_pwm[3 ]; -u8 pwm1_enable; -u8 pwm1_auto_channels_temp; - -u8 stat1; -u8 stat2; }; -static struct amc6821_data *amc6821_update_device (struct device *dev) +static int amc6821_init_auto_point_data (struct amc6821_data *data) { -struct amc6821_data *data =dev_get_drvdata (dev);
drivers/hwmon/amc6821.c static const u8 fan_reg_low[] = {AMC6821_REG_TDATA_LOW, · line 150
Quoted 10 lines
drivers/hwmon/amc6821.c +4
-5-struct i2c_client *client = data->client; -int timeout =HZ ; -u8 reg; -int i; +struct regmap *regmap = data->regmap; +u32 pwm, regval; +int err; -mutex_lock (&data->update_lock); + err =regmap_read (regmap,AMC6821_REG_DCY_LOW_TEMP , &pwm);
I think this is incorrect logic.
amc6821_init_auto_point_data is only called once in init_client, in probe. While we currently do not write to AMC6821_REG_DCY_LOW_TEMP, we could in the future. But writing to it would desynchronise the auto_point_temp values for the new value of the register.
I suggest we put the logic into a function and return the value for a given temp_auto_point (1/2 currently) so that we are calling this function instead of a member in the struct so that we are never caching it unknowingly (regmap would do it for us in any case). It's a bit odd anyway to have only **those** values be cached in the struct as members and migrating everything else.
Quoted 204 lines
drivers/hwmon/amc6821.c +56
-102+if (err) +return err; -if (time_after (jiffies, data->last_updated + timeout) || - !data->valid) { + err =regmap_read (regmap,AMC6821_REG_PSV_TEMP , ®val); +if (err) +return err; + data->temp1_auto_point_temp[0 ] = regval; + data->temp2_auto_point_temp[0 ] = data->temp1_auto_point_temp[0 ]; -for (i =0 ; i <TEMP_IDX_LEN ; i++) - data->temp[i] = (int8_t )i2c_smbus_read_byte_data ( - client, temp_reg[i]); + err =regmap_read (regmap,AMC6821_REG_LTEMP_FAN_CTRL , ®val); +if (err) +return err; + data->temp1_auto_point_temp[1 ] = (regval &0xF8 ) >>1 ; - data->stat1 =i2c_smbus_read_byte_data (client, -AMC6821_REG_STAT1 ); - data->stat2 =i2c_smbus_read_byte_data (client, -AMC6821_REG_STAT2 ); + regval &=0x07 ; + regval =0x20 >> regval; +if (regval) + data->temp1_auto_point_temp[2 ] = + data->temp1_auto_point_temp[1 ] + + (255 - pwm) / regval; +else + data->temp1_auto_point_temp[2 ] =255 ; - data->pwm1 =i2c_smbus_read_byte_data (client, -AMC6821_REG_DCY ); -for (i =0 ; i <FAN1_IDX_LEN ; i++) { - data->fan[i] =i2c_smbus_read_byte_data ( - client, - fan_reg_low[i]); - data->fan[i] +=i2c_smbus_read_byte_data ( - client, - fan_reg_hi[i]) <<8 ; - } - data->fan1_pulses =i2c_smbus_read_byte_data (client, -AMC6821_REG_CONF4 ); - data->fan1_pulses = data->fan1_pulses &AMC6821_CONF4_PSPR ?4 :2 ; + err =regmap_read (regmap,AMC6821_REG_RTEMP_FAN_CTRL , ®val); +if (err) +return err; - data->pwm1_auto_point_pwm[0 ] =0 ; - data->pwm1_auto_point_pwm[2 ] =255 ; - data->pwm1_auto_point_pwm[1 ] =i2c_smbus_read_byte_data (client, -AMC6821_REG_DCY_LOW_TEMP ); + data->temp2_auto_point_temp[1 ] = (regval &0xF8 ) >>1 ; + regval &=0x07 ; + regval =0x20 >> regval; - data->temp1_auto_point_temp[0 ] = -i2c_smbus_read_byte_data (client, -AMC6821_REG_PSV_TEMP ); - data->temp2_auto_point_temp[0 ] = - data->temp1_auto_point_temp[0 ]; - reg =i2c_smbus_read_byte_data (client, -AMC6821_REG_LTEMP_FAN_CTRL ); - data->temp1_auto_point_temp[1 ] = (reg &0xF8 ) >>1 ; - reg &=0x07 ; - reg =0x20 >> reg; -if (reg >0 ) - data->temp1_auto_point_temp[2 ] = - data->temp1_auto_point_temp[1 ] + - (data->pwm1_auto_point_pwm[2 ] - - data->pwm1_auto_point_pwm[1 ]) / reg; -else - data->temp1_auto_point_temp[2 ] =255 ; +if (regval) + data->temp2_auto_point_temp[2 ] = + data->temp2_auto_point_temp[1 ] + + (255 - pwm) / regval; +else + data->temp2_auto_point_temp[2 ] =255 ; - reg =i2c_smbus_read_byte_data (client, -AMC6821_REG_RTEMP_FAN_CTRL ); - data->temp2_auto_point_temp[1 ] = (reg &0xF8 ) >>1 ; - reg &=0x07 ; - reg =0x20 >> reg; -if (reg >0 ) - data->temp2_auto_point_temp[2 ] = - data->temp2_auto_point_temp[1 ] + - (data->pwm1_auto_point_pwm[2 ] - - data->pwm1_auto_point_pwm[1 ]) / reg; -else - data->temp2_auto_point_temp[2 ] =255 ; - - reg =i2c_smbus_read_byte_data (client,AMC6821_REG_CONF1 ); - reg = (reg >>5 ) &0x3 ; -switch (reg) { -case 0 :/*open loop: software sets pwm1*/ - data->pwm1_auto_channels_temp =0 ; - data->pwm1_enable =1 ; -break ; -case 2 :/*closed loop: remote T (temp2)*/ - data->pwm1_auto_channels_temp =2 ; - data->pwm1_enable =2 ; -break ; -case 3 :/*closed loop: local and remote T (temp2)*/ - data->pwm1_auto_channels_temp =3 ; - data->pwm1_enable =3 ; -break ; -case 1 :/* -* semi-open loop: software sets rpm, chip controls -* pwm1 -*/ - data->pwm1_auto_channels_temp =0 ; - data->pwm1_enable =4 ; -break ; - } - - data->last_updated = jiffies; - data->valid = true; - } -mutex_unlock (&data->update_lock); -return data; +return 0 ; }static ssize_t temp_show (struct device *dev,struct device_attribute *devattr,char *buf) { -struct amc6821_data *data =amc6821_update_device (dev); +struct amc6821_data *data =dev_get_drvdata (dev);int ix =to_sensor_dev_attr (devattr)->index; +u32 regval; +int err; -return sprintf (buf,"%d\n" , data->temp[ix] *1000 ); + err =regmap_read (data->regmap, temp_reg[ix], ®val); +if (err) +return err; + +return sysfs_emit (buf,"%d\n" ,sign_extend32 (regval,7 ) *1000 ); }static ssize_t temp_store (struct device *dev,struct device_attribute *attr,const char *buf,size_t count) {struct amc6821_data *data =dev_get_drvdata (dev); -struct i2c_client *client = data->client;int ix =to_sensor_dev_attr (attr)->index;long val; +int err;int ret =kstrtol (buf,10 , &val);if (ret)return ret; val =clamp_val (val /1000 ,-128 ,127 ); -mutex_lock (&data->update_lock); - data->temp[ix] = val; -if (i2c_smbus_write_byte_data (client, temp_reg[ix], data->temp[ix])) { -dev_err (&client->dev,"Register write error, aborting.\n" ); - count = -EIO ; - } -mutex_unlock (&data->update_lock); + err =regmap_write (data->regmap, temp_reg[ix], val); +if (err) +return err; +return count; }static ssize_t temp_alarm_show (struct device *dev,struct device_attribute *devattr,char *buf) { -struct amc6821_data *data =amc6821_update_device (dev); +struct amc6821_data *data =dev_get_drvdata (dev);int ix =to_sensor_dev_attr (devattr)->index; -u8 flag; +u32 regval, mask, reg; +int err;switch (ix) {case IDX_TEMP1_MIN : - flag = data->stat1 &AMC6821_STAT1_LTL ; + reg =AMC6821_REG_STAT1 ; + mask =AMC6821_STAT1_LTL ;break ;case IDX_TEMP1_MAX : - flag = data->stat1 &AMC6821_STAT1_LTH ; + reg =AMC6821_REG_STAT1 ; + mask =AMC6821_STAT1_LTH ;break ;case IDX_TEMP1_CRIT : - flag = data->stat2 &AMC6821_STAT2_LTC ; + reg =AMC6821_REG_STAT2 ; + mask =AMC6821_STAT2_LTC ;break ;case IDX_TEMP2_MIN : - flag = data->stat1 &AMC6821_STAT1_RTL ; + reg =AMC6821_REG_STAT1 ; + mask =AMC6821_STAT1_RTL ;break ;case IDX_TEMP2_MAX : - flag = data->stat1 &AMC6821_STAT1_RTH ;
drivers/hwmon/amc6821.c static const u8 fan_reg_low[] = {AMC6821_REG_TDATA_LOW, · line 327
Quoted 10 lines
drivers/hwmon/amc6821.c +4
-2+ reg =AMC6821_REG_STAT1 ; + mask =AMC6821_STAT1_RTH ;break ;case IDX_TEMP2_CRIT : - flag = data->stat2 &AMC6821_STAT2_RTC ; + reg =AMC6821_REG_STAT2 ; + mask =AMC6821_STAT2_RTC ;break ;default : -dev_dbg (dev,"Unknown attr->index (%d).\n" , ix);
Was this an intended removal? I think we can afford keeping it in?
Quoted 207 lines
drivers/hwmon/amc6821.c +88
-51return -EINVAL ; } -if (flag) -return sprintf (buf,"1" ); -else -return sprintf (buf,"0" ); + err =regmap_read (data->regmap, reg, ®val); +if (err) +return err; +return sysfs_emit (buf,"%d\n" , !!(regval & mask)); }static ssize_t temp2_fault_show (struct device *dev,struct device_attribute *devattr,char *buf) { -struct amc6821_data *data =amc6821_update_device (dev); -if (data->stat1 &AMC6821_STAT1_RTF ) -return sprintf (buf,"1" ); -else -return sprintf (buf,"0" ); +struct amc6821_data *data =dev_get_drvdata (dev); +u32 regval; +int err; + + err =regmap_read (data->regmap,AMC6821_REG_STAT1 , ®val); +if (err) +return err; + +return sysfs_emit (buf,"%d\n" , !!(regval &AMC6821_STAT1_RTF )); }static ssize_t pwm1_show (struct device *dev,struct device_attribute *devattr,char *buf) { -struct amc6821_data *data =amc6821_update_device (dev); -return sprintf (buf,"%d\n" , data->pwm1); +struct amc6821_data *data =dev_get_drvdata (dev); +u32 regval; +int err; + + err =regmap_read (data->regmap,AMC6821_REG_DCY , ®val); +if (err) +return err; + +return sysfs_emit (buf,"%d\n" , regval); } static ssize_t pwm1_store(struct device *dev,@@ -355,24 +299,43 @@ static ssize_t pwm1_store(struct device *dev, size_t count) {struct amc6821_data *data =dev_get_drvdata (dev); -struct i2c_client *client = data->client;u8 val;int ret =kstrtou8 (buf,10 , &val);if (ret)return ret; -mutex_lock (&data->update_lock); - data->pwm1 = val; -i2c_smbus_write_byte_data (client,AMC6821_REG_DCY , data->pwm1); -mutex_unlock (&data->update_lock); + ret =regmap_write (data->regmap,AMC6821_REG_DCY , val); +if (ret) +return ret; +return count; }static ssize_t pwm1_enable_show (struct device *dev,struct device_attribute *devattr,char *buf) { -struct amc6821_data *data =amc6821_update_device (dev); -return sprintf (buf,"%d\n" , data->pwm1_enable); +struct amc6821_data *data =dev_get_drvdata (dev); +int err; +u32 val; + + err =regmap_read (data->regmap,AMC6821_REG_CONF1 , &val); +if (err) +return err; +switch (val & (AMC6821_CONF1_FDRC0 |AMC6821_CONF1_FDRC1 )) { +case 0 : + val =1 ;/* manual */ +break ; +case AMC6821_CONF1_FDRC0 : + val =4 ;/* target rpm (fan1_target) controlled */ +break ; +case AMC6821_CONF1_FDRC1 : + val =2 ;/* remote temp controlled */ +break ; +default : + val =3 ;/* max(local, remote) temp controlled */ +break ; + } +return sysfs_emit (buf,"%d\n" , val); } static ssize_t pwm1_enable_store(struct device *dev,@@ -380,49 +343,37 @@ static ssize_t pwm1_enable_store(struct device *dev, const char *buf, size_t count) {struct amc6821_data *data =dev_get_drvdata (dev); -struct i2c_client *client = data->client;long val; -int config =kstrtol (buf,10 , &val); -if (config) -return config; +u32 mode; +int err; -mutex_lock (&data->update_lock); - config =i2c_smbus_read_byte_data (client,AMC6821_REG_CONF1 ); -if (config <0 ) { -dev_err (&client->dev, -"Error reading configuration register, aborting.\n" ); - count = config; - goto unlock; - } + err =kstrtol (buf,10 , &val); +if (err) +return err;switch (val) {case 1 : - config &= ~AMC6821_CONF1_FDRC0 ; - config &= ~AMC6821_CONF1_FDRC1 ; + mode =0 ;break ;case 2 : - config &= ~AMC6821_CONF1_FDRC0 ; - config |=AMC6821_CONF1_FDRC1 ; + mode =AMC6821_CONF1_FDRC1 ;break ;case 3 : - config |=AMC6821_CONF1_FDRC0 ; - config |=AMC6821_CONF1_FDRC1 ; + mode =AMC6821_CONF1_FDRC0 |AMC6821_CONF1_FDRC1 ;break ;case 4 : - config |=AMC6821_CONF1_FDRC0 ; - config &= ~AMC6821_CONF1_FDRC1 ; + mode =AMC6821_CONF1_FDRC0 ;break ;default : - count = -EINVAL ; - goto unlock; +return -EINVAL ; } -if (i2c_smbus_write_byte_data (client,AMC6821_REG_CONF1 , config)) { -dev_err (&client->dev, -"Configuration register write error, aborting.\n" ); - count = -EIO ; - } -unlock: -mutex_unlock (&data->update_lock); + + err =regmap_update_bits (data->regmap,AMC6821_REG_CONF1 , +AMC6821_CONF1_FDRC0 |AMC6821_CONF1_FDRC1 , + mode); +if (err) +return err; +return count; }@@ -430,26 +381,45 @@ static ssize_t pwm1_auto_channels_temp_show(struct device *dev,struct device_attribute *devattr, char *buf) { - struct amc6821_data *data = amc6821_update_device(dev); -return sprintf (buf,"%d\n" , data->pwm1_auto_channels_temp); + struct amc6821_data *data = dev_get_drvdata(dev); +u32 val; +int err; + + err =regmap_read (data->regmap,AMC6821_REG_CONF1 , &val); +if (err) +return err; +switch (val & (AMC6821_CONF1_FDRC0 |AMC6821_CONF1_FDRC1 )) { +case 0 : +case AMC6821_CONF1_FDRC0 : + val =0 ;/* manual or target rpm controlled */ +break ; +case AMC6821_CONF1_FDRC1 : + val =2 ;/* remote temp controlled */ +break ; +default : + val =3 ;/* max(local, remote) temp controlled */ +break ; + } + +return sysfs_emit (buf,"%d\n" , val); }static ssize_t temp_auto_point_temp_show (struct device *dev,struct device_attribute *devattr,char *buf) { +struct amc6821_data *data =dev_get_drvdata (dev);int ix =to_sensor_dev_attr_2 (devattr)->index;int nr =to_sensor_dev_attr_2 (devattr)->nr; -struct amc6821_data *data =amc6821_update_device (dev); +switch (nr) {case 1 : - return sprintf(buf, "%d\n",
drivers/hwmon/amc6821.c static ssize_t pwm1_auto_channels_temp_show(struct device *dev, · line 452
Quoted 10 lines
drivers/hwmon/amc6821.c +4
-4- data->temp1_auto_point_temp[ix] * 1000); +return sysfs_emit (buf,"%d\n" , + data->temp1_auto_point_temp[ix] *1000 );case 2 : -return sprintf (buf,"%d\n" , - data->temp2_auto_point_temp[ix] *1000 ); +return sysfs_emit (buf,"%d\n" , + data->temp2_auto_point_temp[ix] *1000 );default : -dev_dbg (dev,"Unknown attr->nr (%d).\n" , nr);
Ditto.
Quoted 82 lines
drivers/hwmon/amc6821.c +33
-18return -EINVAL ; } }@@ -458,44 +428,59 @@ static ssize_t pwm1_auto_point_pwm_show(struct device *dev,struct device_attribute *devattr, char *buf) { + struct amc6821_data *data = dev_get_drvdata(dev);int ix =to_sensor_dev_attr (devattr)->index; -struct amc6821_data *data =amc6821_update_device (dev); -return sprintf (buf,"%d\n" , data->pwm1_auto_point_pwm[ix]); +u32 val; +int err; + +switch (ix) { +case 0 : + val =0 ; +break ; +case 1 : + err =regmap_read (data->regmap,AMC6821_REG_DCY_LOW_TEMP , &val); +if (err) +return err; +break ; +default : + val =255 ; +break ; + } +return sysfs_emit (buf,"%d\n" , val); } -static inline ssize_t set_slope_register (struct i2c_client *client, -u8 reg, -u8 dpwm, -u8 *ptemp) +static inline int set_slope_register (struct regmap *regmap, +u8 reg,u8 *ptemp) { -int dt; -u8 tmp; +u8 tmp, dpwm; +int err, dt; +u32 pwm; - dt = ptemp[2 ]-ptemp[1 ]; + err =regmap_read (regmap,AMC6821_REG_DCY_LOW_TEMP , &pwm); +if (err) +return err; + + dpwm =255 - pwm; + + dt = ptemp[2 ] - ptemp[1 ];for (tmp =4 ; tmp >0 ; tmp--) {if (dt * (0x20 >> tmp) >= dpwm)break ; } tmp |= (ptemp[1 ] &0x7C ) <<1 ; -if (i2c_smbus_write_byte_data (client, - reg, tmp)) { -dev_err (&client->dev,"Register write error, aborting.\n" ); -return -EIO ; - } -return 0 ; +return regmap_write (regmap, reg, tmp); }static ssize_t temp_auto_point_temp_store (struct device *dev,struct device_attribute *attr,const char *buf,size_t count) { -struct amc6821_data *data =amc6821_update_device (dev); -struct i2c_client *client = data->client; +struct amc6821_data *data =dev_get_drvdata (dev);int ix =to_sensor_dev_attr_2 (attr)->index;int nr =to_sensor_dev_attr_2 (attr)->nr; +struct regmap *regmap = data->regmap;u8 *ptemp;u8 reg; -int dpwm;long val;int ret =kstrtol (buf,10 , &val);if (ret)
drivers/hwmon/amc6821.c static ssize_t temp_auto_point_temp_store(struct device *dev, · line 514
Quoted 4 lines
drivers/hwmon/amc6821.c +0
-1@@ -511,12 +496,10 @@ static ssize_t temp_auto_point_temp_store(struct device *dev, reg =AMC6821_REG_RTEMP_FAN_CTRL ;break ;default : -dev_dbg (dev,"Unknown attr->nr (%d).\n" , nr);
Ditto.
Quoted 26 lines
drivers/hwmon/amc6821.c +3
-8return -EINVAL ; }mutex_lock (&data->update_lock); - data->valid = false;switch (ix) {case 0 :@@ -525,13 +508,9 @@ static ssize_t temp_auto_point_temp_store(struct device *dev, ptemp[0 ] =clamp_val (ptemp[0 ],0 , data->temp2_auto_point_temp[1 ]); ptemp[0 ] =clamp_val (ptemp[0 ],0 ,63 ); -if (i2c_smbus_write_byte_data ( - client, -AMC6821_REG_PSV_TEMP , - ptemp[0 ])) { -dev_err (&client->dev, -"Register write error, aborting.\n" ); - count = -EIO ; +if (regmap_write (regmap,AMC6821_REG_PSV_TEMP , ptemp[0 ])) { +dev_err (dev,"Register write error, aborting.\n" ); + count = -EIO ; } goto EXIT;case 1 :
drivers/hwmon/amc6821.c static ssize_t temp_auto_point_temp_store(struct device *dev, · line 546
Quoted 4 lines
drivers/hwmon/amc6821.c +0
-1@@ -543,12 +522,10 @@ static ssize_t temp_auto_point_temp_store(struct device *dev, ptemp[2 ] =clamp_val (val /1000 , ptemp[1 ]+1 ,255 );break ;default : -dev_dbg (dev,"Unknown attr->index (%d).\n" , ix);
Ditto.
Quoted 11 lines
drivers/hwmon/amc6821.c +1
-2count = -EINVAL ; goto EXIT; } - dpwm = data->pwm1_auto_point_pwm[2 ] - data->pwm1_auto_point_pwm[1 ]; -if (set_slope_register (client, reg, dpwm, ptemp)) +if (set_slope_register (regmap, reg, ptemp)) count = -EIO ; EXIT:@@ -561,10 +538,11 @@ static ssize_t pwm1_auto_point_pwm_store(struct device *dev, const char *buf, size_t count)
drivers/hwmon/amc6821.c static ssize_t pwm1_auto_point_pwm_store(struct device *dev, · line 545
Quoted 10 lines
drivers/hwmon/amc6821.c +4
-3{struct amc6821_data *data =dev_get_drvdata (dev); -struct i2c_client *client = data->client; -int dpwm; +struct regmap *regmap = data->regmap;u8 val; -int ret =kstrtou8 (buf,10 , &val); +int ret; + + ret =kstrtou8 (buf,10 , &val);
Not sure this cosmetic change is worth it? Or maybe squash with an earlier commit?
Quoted 5 lines
drivers/hwmon/amc6821.c +0
-0if (ret)return ret;@@ -572,27 +550,24 @@ static ssize_t pwm1_auto_point_pwm_store(struct device *dev,return -EINVAL ;
drivers/hwmon/amc6821.c static ssize_t pwm1_auto_point_pwm_store(struct device *dev, · line 554
Quoted 10 lines
drivers/hwmon/amc6821.c +2
-6mutex_lock (&data->update_lock); - data->pwm1_auto_point_pwm[1 ] = val; -if (i2c_smbus_write_byte_data (client,AMC6821_REG_DCY_LOW_TEMP , - data->pwm1_auto_point_pwm[1 ])) { -dev_err (&client->dev,"Register write error, aborting.\n" ); - count = -EIO ; - goto EXIT; + ret =regmap_write (regmap,AMC6821_REG_DCY_LOW_TEMP , val); +if (ret)
I think we're missing a count = something here?
drivers/hwmon/amc6821.c static ssize_t pwm1_auto_point_pwm_store(struct device *dev, · line 560
Quoted 6 lines
drivers/hwmon/amc6821.c +6
-0+ goto unlock; + + ret =set_slope_register (regmap,AMC6821_REG_LTEMP_FAN_CTRL , + data->temp1_auto_point_temp); +if (ret) { + count = ret;
In some places, we replace set_slope_register return code with -EIO (like it was) and sometimes we propagate it, like here. Is there some reason for this or can we have some kind of consistency across the code base here?
Looks good to me otherwise.
Cheers,
Quentin
Guenter Roeck
maintainerRe: [PATCH v2 09/11] hwmon: (amc6821) Convert to use regmap
Quoted 121 lines · Quentin Schulz
Hi Guenter,
Quoted 105 lines · Guenter Roeck
Use regmap for register accesses and for most caching.
While at it, use
sysfs_emit()instead ofsprintf()to write sysfs attribute data, and remove spurious debug messages which would only be seen as result of a bug in the code.No functional change intended.
Signed-off-by Guenter Roeck <[email protected]>---
v2: Drop another spurious debug message in this patch instead of patch 10 Add missing "selectREGMAP_I2C" toKconfig
Change misleading variable name from 'mask' to 'mode'. Usesysfs_emitinstead of sprintf everywheredrivers/hwmon/Kconfig | 1 +
drivers/hwmon/amc6821.c| 713 ++++++++++++++++++----------------------2 files changed, 329 insertions(+), 385 deletions(-)drivers/hwmon/Kconfig +0
-0@@ -2127,6 +2127,7 @@ config SENSORS_ADS7871config
SENSORS_AMC6821
tristate "Texas Instruments AMC6821"
depends on I2C
+ selectREGMAP_I2C
help
If you say yes here you get support for the Texas Instruments AMC6821 hardware monitoring chips.drivers/hwmon/amc6821.c +5
-26@@ -8,15 +8,16 @@* Copyright (C) 2007 Hans J. Koch <[email protected]> */ +#include <linux/bitops.h> #include <linux/bits.h> #include <linux/err.h> #include <linux/hwmon.h> #include <linux/hwmon-sysfs.h> #include <linux/i2c.h> #include <linux/init.h> -#include <linux/jiffies.h> #include <linux/module.h> #include <linux/mutex.h> +#include <linux/regmap.h> #include <linux/slab.h> /*@@ -44,6 +45,7 @@ module_param(init, int, 0444); #define AMC6821_REG_CONF4 0x04 #define AMC6821_REG_STAT1 0x02 #define AMC6821_REG_STAT2 0x03 +#define AMC6821_REG_TEMP_LO 0x06 #define AMC6821_REG_TDATA_LOW 0x08 #define AMC6821_REG_TDATA_HI 0x09 #define AMC6821_REG_LTEMP_HI 0x0A@@ -61,11 +63,8 @@ module_param(init, int, 0444); #define AMC6821_REG_DCY_LOW_TEMP 0x21 #define AMC6821_REG_TACH_LLIMITL 0x10 -#define AMC6821_REG_TACH_LLIMITH 0x11 #define AMC6821_REG_TACH_HLIMITL 0x12 -#define AMC6821_REG_TACH_HLIMITH 0x13 #define AMC6821_REG_TACH_SETTINGL 0x1e -#define AMC6821_REG_TACH_SETTINGH 0x1f #define AMC6821_CONF1_START BIT(0) #define AMC6821_CONF1_FAN_INT_EN BIT(1)@@ -130,224 +129,169 @@ static const u8 fan_reg_low[] = {AMC6821_REG_TDATA_LOW, AMC6821_REG_TACH_HLIMITL, AMC6821_REG_TACH_SETTINGL, }; -static const u8 fan_reg_hi[] = {AMC6821_REG_TDATA_HI , - AMC6821_REG_TACH_LLIMITH, - AMC6821_REG_TACH_HLIMITH, - AMC6821_REG_TACH_SETTINGH, }; - /* * Client data (each client gets its own) */ struct amc6821_data { - struct i2c_client *client; + struct regmap *regmap; struct mutex update_lock; - bool valid; /* false until following fields are valid */ - unsigned long last_updated; /* in jiffies */ - /* register values */ - int temp[TEMP_IDX_LEN]; - - u16 fan[FAN1_IDX_LEN]; - u8 fan1_pulses; - - u8 pwm1; u8 temp1_auto_point_temp[3]; u8 temp2_auto_point_temp[3]; - u8 pwm1_auto_point_pwm[3]; - u8 pwm1_enable; - u8 pwm1_auto_channels_temp; - - u8 stat1; - u8 stat2; }; -static struct amc6821_data *amc6821_update_device (struct device *dev) +static int amc6821_init_auto_point_data (struct amc6821_data *data) {drivers/hwmon/amc6821.c static const u8 fan_reg_low[] = {AMC6821_REG_TDATA_LOW, · line 145
Quoted 10 lines
drivers/hwmon/amc6821.c +4
-6- struct amc6821_data *data = dev_get_drvdata(dev); - struct i2c_client *client = data->client; - int timeout = HZ; - u8 reg; - int i; + struct regmap *regmap = data->regmap; + u32 pwm, regval; + int err; - mutex_lock(&data->update_lock); + err = regmap_read(regmap, AMC6821_REG_DCY_LOW_TEMP, &pwm);I think this is incorrect logic.
Quoted 2 lines
amc6821_init_auto_point_datais only called once ininit_client, in probe. While we currently do not write toAMC6821_REG_DCY_LOW_TEMP, we could in the future. But writing to it would desynchronise theauto_point_tempvalues for the new value of the register.
We do write the register, in pwm1_auto_point_pwm_store().
Quoted 1 line
I suggest we put the logic into a function and return the value for a given
temp_auto_point(1/2 currently) so that we are calling this function instead of a member in the struct so that we are never caching it unknowingly (regmap would do it for us in any case). It's a bit odd anyway to have only **those** values be cached in the struct as members and migrating everything else.
Yes, I know, that is a bit odd. Essentially I was too lazy to clean that up. But, yes, you are correct, that results in the cached values being wrong after AMC6821_REG_DCY_LOW_TEMP is updated. Back to the drawing board, and thanks for finding this.
[ ... ]
Quoted 4 lines
Quoted 2 lines
default:
-dev_dbg(dev, "Unknown attr->index (%d).\n", ix);Was this an intended removal? I think we can afford keeping it in?
Yes, it is intentional. It (and the others below) indicate a coding error, which would have been found during development. While it does make sense to keep the default: case to make the compiler happy, it doesn't make sense to keep the pointless message in the code.
Quoted 6 lines
Quoted 6 lines
drivers/hwmon/amc6821.c +0
-2@@ -561,10 +538,11 @@ static ssize_t pwm1_auto_point_pwm_store(struct device *dev, const char *buf, size_t count) { struct amc6821_data *data = dev_get_drvdata(dev); - struct i2c_client *client = data->client; - int dpwm;
Quoted 9 lines
drivers/hwmon/amc6821.c static ssize_t pwm1_auto_point_pwm_store(struct device *dev, · line 545
Quoted 6 lines
drivers/hwmon/amc6821.c +4
-1+ struct regmap *regmap = data->regmap; u8 val; - int ret = kstrtou8(buf, 10, &val); + int ret; + + ret = kstrtou8(buf, 10, &val);Not sure this cosmetic change is worth it? Or maybe squash with an earlier commit?
That slipped in, I think from the first patch of the series. I'll move it there.
Quoted 7 lines
Quoted 7 lines
drivers/hwmon/amc6821.c +0
-2if (ret) return ret;@@ -572,27 +550,24 @@ static ssize_t pwm1_auto_point_pwm_store(struct device *dev, return -EINVAL; mutex_lock(&data->update_lock); - data->pwm1_auto_point_pwm[1] = val; - if (i2c_smbus_write_byte_data(client, AMC6821_REG_DCY_LOW_TEMP,
Quoted 9 lines
drivers/hwmon/amc6821.c static ssize_t pwm1_auto_point_pwm_store(struct device *dev, · line 554
Quoted 6 lines
drivers/hwmon/amc6821.c +2
-4- data->pwm1_auto_point_pwm[1])) { - dev_err(&client->dev, "Register write error, aborting.\n"); - count = -EIO; - goto EXIT; + ret = regmap_write(regmap, AMC6821_REG_DCY_LOW_TEMP, val); + if (ret)I think we're missing a count = something here?
Yes.
Quoted 9 lines
drivers/hwmon/amc6821.c static ssize_t pwm1_auto_point_pwm_store(struct device *dev, · line 560
Quoted 6 lines
drivers/hwmon/amc6821.c +6
-0+ goto unlock; + + ret = set_slope_register(regmap, AMC6821_REG_LTEMP_FAN_CTRL, + data->temp1_auto_point_temp); + if (ret) { + count = ret;In some places, we replace
set_slope_registerreturn code with-EIO(like it was) and sometimes we propagate it, like here. Is there some reason for this or can we have some kind of consistency across the code base here?
Thanks for noticing. The code should be consistent and always propagate the error code. I'll fix it.
Thanks,
Guenter
Guenter Roeck
maintainerPATCH v2 10/11 hwmon: (amc6821) Convert to with_info API
In reply to Guenter RoeckConvert to use with_info API to simplify the code and make it easier to maintain. This also reduces code size by approximately 20%.
No functional change intended.
---
v2: Adjust to changes made in preceding patches
drivers/hwmon/amc6821.c | 744 +++++++++++++++++++++------------------- 1 file changed, 390 insertions(+), 354 deletions(-)
drivers/hwmon/amc6821.c +390 -354
@@ -6,6 +6,9 @@* * Based on max6650.c: * Copyright (C) 2007 Hans J. Koch <[email protected]> +* +* Conversion to regmap and with_info API: +* Copyright (C) 2024 Guenter Roeck <[email protected]> */ #include <linux/bitops.h>
@@ -107,28 +110,6 @@ module_param(init, int, 0444);#define AMC6821_STAT2_L_THERM BIT(6)#define AMC6821_STAT2_THERM_IN BIT(7) -enum {IDX_TEMP1_INPUT =0 ,IDX_TEMP1_MIN ,IDX_TEMP1_MAX , -IDX_TEMP1_CRIT ,IDX_TEMP2_INPUT ,IDX_TEMP2_MIN , -IDX_TEMP2_MAX ,IDX_TEMP2_CRIT , -TEMP_IDX_LEN , }; - -static const u8 temp_reg[] = {AMC6821_REG_LTEMP_HI , -AMC6821_REG_LTEMP_LIMIT_MIN , -AMC6821_REG_LTEMP_LIMIT_MAX , -AMC6821_REG_LTEMP_CRIT , -AMC6821_REG_RTEMP_HI , -AMC6821_REG_RTEMP_LIMIT_MIN , -AMC6821_REG_RTEMP_LIMIT_MAX , -AMC6821_REG_RTEMP_CRIT , }; - -enum {IDX_FAN1_INPUT =0 ,IDX_FAN1_MIN ,IDX_FAN1_MAX ,IDX_FAN1_TARGET , -FAN1_IDX_LEN , }; - -static const u8 fan_reg_low[] = {AMC6821_REG_TDATA_LOW , -AMC6821_REG_TACH_LLIMITL , -AMC6821_REG_TACH_HLIMITL , -AMC6821_REG_TACH_SETTINGL , }; -/* * Client data (each client gets its own) */
@@ -189,219 +170,319 @@ static int amc6821_init_auto_point_data(struct amc6821_data *data)return 0 ; } -static ssize_t temp_show (struct device *dev,struct device_attribute *devattr, -char *buf) +static int amc6821_temp_read_values (struct regmap *regmap,u32 attr,int channel,long *val) { -struct amc6821_data *data =dev_get_drvdata (dev); -int ix =to_sensor_dev_attr (devattr)->index; +int reg, err;u32 regval; -int err; - err =regmap_read (data->regmap, temp_reg[ix], ®val); -if (err) -return err; - -return sysfs_emit (buf,"%d\n" ,sign_extend32 (regval,7 ) *1000 ); -} - -static ssize_t temp_store (struct device *dev,struct device_attribute *attr, -const char *buf,size_t count) -{ -struct amc6821_data *data =dev_get_drvdata (dev); -int ix =to_sensor_dev_attr (attr)->index; -long val; -int err; - -int ret =kstrtol (buf,10 , &val); -if (ret) -return ret; - val =clamp_val (val /1000 ,-128 ,127 ); - - err =regmap_write (data->regmap, temp_reg[ix], val); -if (err) -return err; - -return count; -} - -static ssize_t temp_alarm_show (struct device *dev, -struct device_attribute *devattr,char *buf) -{ -struct amc6821_data *data =dev_get_drvdata (dev); -int ix =to_sensor_dev_attr (devattr)->index; -u32 regval, mask, reg; -int err; - -switch (ix) { -case IDX_TEMP1_MIN : - reg =AMC6821_REG_STAT1 ; - mask =AMC6821_STAT1_LTL ; +switch (attr) { +case hwmon_temp_input: + reg = channel ?AMC6821_REG_RTEMP_HI :AMC6821_REG_LTEMP_HI ;break ; -case IDX_TEMP1_MAX : - reg =AMC6821_REG_STAT1 ; - mask =AMC6821_STAT1_LTH ; +case hwmon_temp_min: + reg = channel ?AMC6821_REG_RTEMP_LIMIT_MIN :AMC6821_REG_LTEMP_LIMIT_MIN ;break ; -case IDX_TEMP1_CRIT : - reg =AMC6821_REG_STAT2 ; - mask =AMC6821_STAT2_LTC ; +case hwmon_temp_max: + reg = channel ?AMC6821_REG_RTEMP_LIMIT_MAX :AMC6821_REG_LTEMP_LIMIT_MAX ;break ; -case IDX_TEMP2_MIN : - reg =AMC6821_REG_STAT1 ; - mask =AMC6821_STAT1_RTL ; -break ; -case IDX_TEMP2_MAX : - reg =AMC6821_REG_STAT1 ; - mask =AMC6821_STAT1_RTH ; -break ; -case IDX_TEMP2_CRIT : - reg =AMC6821_REG_STAT2 ; - mask =AMC6821_STAT2_RTC ; +case hwmon_temp_crit: + reg = channel ?AMC6821_REG_RTEMP_CRIT :AMC6821_REG_LTEMP_CRIT ;break ;default : -return -EINVAL ; +return -EOPNOTSUPP ; } - err =regmap_read (data->regmap, reg, ®val); + err =regmap_read (regmap, reg, ®val);if (err)return err; -return sysfs_emit (buf,"%d\n" , !!(regval & mask)); + *val =sign_extend32 (regval,7 ) *1000 ; +return 0 ; } -static ssize_t temp2_fault_show (struct device *dev, -struct device_attribute *devattr,char *buf) +static int amc6821_read_alarms (struct regmap *regmap,enum hwmon_sensor_types type, +u32 attr,int channel,long *val) { -struct amc6821_data *data =dev_get_drvdata (dev); +int reg, mask, err;u32 regval; -int err; - err =regmap_read (data->regmap,AMC6821_REG_STAT1 , ®val); -if (err) -return err; - -return sysfs_emit (buf,"%d\n" , !!(regval &AMC6821_STAT1_RTF )); -} - -static ssize_t pwm1_show (struct device *dev,struct device_attribute *devattr, -char *buf) -{ -struct amc6821_data *data =dev_get_drvdata (dev); -u32 regval; -int err; - - err =regmap_read (data->regmap,AMC6821_REG_DCY , ®val); -if (err) -return err; - -return sysfs_emit (buf,"%d\n" , regval); -} - -static ssize_t pwm1_store (struct device *dev, -struct device_attribute *devattr,const char *buf, -size_t count) -{ -struct amc6821_data *data =dev_get_drvdata (dev); -u8 val; -int ret =kstrtou8 (buf,10 , &val); -if (ret) -return ret; - - ret =regmap_write (data->regmap,AMC6821_REG_DCY , val); -if (ret) -return ret; - -return count; -} - -static ssize_t pwm1_enable_show (struct device *dev, -struct device_attribute *devattr,char *buf) -{ -struct amc6821_data *data =dev_get_drvdata (dev); -int err; -u32 val; - - err =regmap_read (data->regmap,AMC6821_REG_CONF1 , &val); -if (err) -return err; -switch (val & (AMC6821_CONF1_FDRC0 |AMC6821_CONF1_FDRC1 )) { -case 0 : - val =1 ;/* manual */ +switch (type) { +case hwmon_temp: +switch (attr) { +case hwmon_temp_min_alarm: + reg =AMC6821_REG_STAT1 ; + mask = channel ?AMC6821_STAT1_RTL :AMC6821_STAT1_LTL ; +break ; +case hwmon_temp_max_alarm: + reg =AMC6821_REG_STAT1 ; + mask = channel ?AMC6821_STAT1_RTH :AMC6821_STAT1_LTH ; +break ; +case hwmon_temp_crit_alarm: + reg =AMC6821_REG_STAT2 ; + mask = channel ?AMC6821_STAT2_RTC :AMC6821_STAT2_LTC ; +break ; +case hwmon_temp_fault: + reg =AMC6821_REG_STAT1 ; + mask =AMC6821_STAT1_RTF ; +break ; +default : +return -EOPNOTSUPP ; + }break ; -case AMC6821_CONF1_FDRC0 : - val =4 ;/* target rpm (fan1_target) controlled */ -break ; -case AMC6821_CONF1_FDRC1 : - val =2 ;/* remote temp controlled */ +case hwmon_fan: +switch (attr) { +case hwmon_fan_fault: + reg =AMC6821_REG_STAT1 ; + mask =AMC6821_STAT1_FANS ; +break ; +default : +return -EOPNOTSUPP ; + }break ;default : - val =3 ;/* max(local, remote) temp controlled */ -break ; +return -EOPNOTSUPP ; } -return sysfs_emit (buf,"%d\n" , val); + err =regmap_read (regmap, reg, ®val); +if (err) +return err; + *val = !!(regval & mask); +return 0 ; } -static ssize_t pwm1_enable_store (struct device *dev, -struct device_attribute *attr, -const char *buf,size_t count) +static int amc6821_temp_read (struct device *dev,u32 attr,int channel,long *val) {struct amc6821_data *data =dev_get_drvdata (dev); -long val; + +switch (attr) { +case hwmon_temp_input: +case hwmon_temp_min: +case hwmon_temp_max: +case hwmon_temp_crit: +return amc6821_temp_read_values (data->regmap, attr, channel, val); +case hwmon_temp_min_alarm: +case hwmon_temp_max_alarm: +case hwmon_temp_crit_alarm: +case hwmon_temp_fault: +return amc6821_read_alarms (data->regmap, hwmon_temp, attr, channel, val); +default : +return -EOPNOTSUPP ; + } +} + +static int amc6821_temp_write (struct device *dev,u32 attr,int channel,long val) +{ +struct amc6821_data *data =dev_get_drvdata (dev); +int reg; + + val =DIV_ROUND_CLOSEST (clamp_val (val,-128000 ,127000 ),1000 ); + +switch (attr) { +case hwmon_temp_min: + reg = channel ?AMC6821_REG_RTEMP_LIMIT_MIN :AMC6821_REG_LTEMP_LIMIT_MIN ; +break ; +case hwmon_temp_max: + reg = channel ?AMC6821_REG_RTEMP_LIMIT_MAX :AMC6821_REG_LTEMP_LIMIT_MAX ; +break ; +case hwmon_temp_crit: + reg = channel ?AMC6821_REG_RTEMP_CRIT :AMC6821_REG_LTEMP_CRIT ; +break ; +default : +return -EOPNOTSUPP ; + } +return regmap_write (data->regmap, reg, val); +} + +static int amc6821_pwm_read (struct device *dev,u32 attr,long *val) +{ +struct amc6821_data *data =dev_get_drvdata (dev); +struct regmap *regmap = data->regmap; +u32 regval; +int err; + +switch (attr) { +case hwmon_pwm_enable: + err =regmap_read (regmap,AMC6821_REG_CONF1 , ®val); +if (err) +return err; +switch (regval & (AMC6821_CONF1_FDRC0 |AMC6821_CONF1_FDRC1 )) { +case 0 : + *val =1 ;/* manual */ +break ; +case AMC6821_CONF1_FDRC0 : + *val =4 ;/* target rpm (fan1_target) controlled */ +break ; +case AMC6821_CONF1_FDRC1 : + *val =2 ;/* remote temp controlled */ +break ; +default : + *val =3 ;/* max(local, remote) temp controlled */ +break ; + } +return 0 ; +case hwmon_pwm_auto_channels_temp: + err =regmap_read (regmap,AMC6821_REG_CONF1 , ®val); +if (err) +return err; +switch (regval & (AMC6821_CONF1_FDRC0 |AMC6821_CONF1_FDRC1 )) { +case 0 : +case AMC6821_CONF1_FDRC0 : + *val =0 ;/* manual or target rpm controlled */ +break ; +case AMC6821_CONF1_FDRC1 : + *val =2 ;/* remote temp controlled */ +break ; +default : + *val =3 ;/* max(local, remote) temp controlled */ +break ; + } +return 0 ; +case hwmon_pwm_input: + err =regmap_read (regmap,AMC6821_REG_DCY , ®val); +if (err) +return err; + *val = regval; +return 0 ; +default : +return -EOPNOTSUPP ; + } +} + +static int amc6821_pwm_write (struct device *dev,u32 attr,long val) +{ +struct amc6821_data *data =dev_get_drvdata (dev); +struct regmap *regmap = data->regmap;u32 mode; -int err; - err =kstrtol (buf,10 , &val); -if (err) -return err; - -switch (val) { -case 1 : - mode =0 ; -break ; -case 2 : - mode =AMC6821_CONF1_FDRC1 ; -break ; -case 3 : - mode =AMC6821_CONF1_FDRC0 |AMC6821_CONF1_FDRC1 ; -break ; -case 4 : - mode =AMC6821_CONF1_FDRC0 ; -break ; +switch (attr) { +case hwmon_pwm_enable: +switch (val) { +case 1 : + mode =0 ; +break ; +case 2 : + mode =AMC6821_CONF1_FDRC1 ; +break ; +case 3 : + mode =AMC6821_CONF1_FDRC0 |AMC6821_CONF1_FDRC1 ; +break ; +case 4 : + mode =AMC6821_CONF1_FDRC0 ; +break ; +default : +return -EINVAL ; + } +return regmap_update_bits (regmap,AMC6821_REG_CONF1 , +AMC6821_CONF1_FDRC0 |AMC6821_CONF1_FDRC1 , + mode); +case hwmon_pwm_input: +if (val <0 || val >255 ) +return -EINVAL ; +return regmap_write (regmap,AMC6821_REG_DCY , val);default : -return -EINVAL ; +return -EOPNOTSUPP ; } - - err =regmap_update_bits (data->regmap,AMC6821_REG_CONF1 , -AMC6821_CONF1_FDRC0 |AMC6821_CONF1_FDRC1 , - mode); -if (err) -return err; - -return count; } -static ssize_t pwm1_auto_channels_temp_show (struct device *dev, -struct device_attribute *devattr, -char *buf) +static int amc6821_fan_read_rpm (struct regmap *regmap,u32 attr,long *val) { -struct amc6821_data *data =dev_get_drvdata (dev); -u32 val; -int err; +int reg, err; +u8 regs[2 ]; +u32 regval; - err =regmap_read (data->regmap,AMC6821_REG_CONF1 , &val); -if (err) -return err; -switch (val & (AMC6821_CONF1_FDRC0 |AMC6821_CONF1_FDRC1 )) { -case 0 : -case AMC6821_CONF1_FDRC0 : - val =0 ;/* manual or target rpm controlled */ +switch (attr) { +case hwmon_fan_input: + reg =AMC6821_REG_TDATA_LOW ;break ; -case AMC6821_CONF1_FDRC1 : - val =2 ;/* remote temp controlled */ +case hwmon_fan_min: + reg =AMC6821_REG_TACH_LLIMITL ; +break ; +case hwmon_fan_max: + reg =AMC6821_REG_TACH_HLIMITL ; +break ; +case hwmon_fan_target: + reg =AMC6821_REG_TACH_SETTINGL ;break ;default : - val =3 ;/* max(local, remote) temp controlled */ -break ; +return -EOPNOTSUPP ; } -return sysfs_emit (buf,"%d\n" , val); + err =regmap_bulk_read (regmap, reg, regs,2 ); +if (err) +return err; + + regval = (regs[1 ] <<8 ) | regs[0 ]; + *val = regval ?6000000 / regval :0 ; + +return 0 ; +} + +static int amc6821_fan_read (struct device *dev,u32 attr,long *val) +{ +struct amc6821_data *data =dev_get_drvdata (dev); +struct regmap *regmap = data->regmap; +u32 regval; +int err; + +switch (attr) { +case hwmon_fan_input: +case hwmon_fan_min: +case hwmon_fan_max: +case hwmon_fan_target: +return amc6821_fan_read_rpm (regmap, attr, val); +case hwmon_fan_fault: +return amc6821_read_alarms (regmap, hwmon_fan, attr,0 , val); +case hwmon_fan_pulses: + err =regmap_read (regmap,AMC6821_REG_CONF4 , ®val); +if (err) +return err; + *val = (regval &AMC6821_CONF4_PSPR ) ?4 :2 ; +return 0 ; +default : +return -EOPNOTSUPP ; + } +} + +static int amc6821_fan_write (struct device *dev,u32 attr,long val) +{ +struct amc6821_data *data =dev_get_drvdata (dev); +struct regmap *regmap = data->regmap; +u8 regs[2 ]; +int reg; + +if (attr == hwmon_fan_pulses) { +if (val !=2 && val !=4 ) +return -EINVAL ; +return regmap_update_bits (regmap,AMC6821_REG_CONF4 , +AMC6821_CONF4_PSPR , + val ==4 ?AMC6821_CONF4_PSPR :0 ); + } + +if (val <0 ) +return -EINVAL ; + +switch (attr) { +case hwmon_fan_min: +if (!val)/* no unlimited minimum speed */ +return -EINVAL ; + reg =AMC6821_REG_TACH_LLIMITL ; +break ; +case hwmon_fan_max: + reg =AMC6821_REG_TACH_HLIMITL ; +break ; +case hwmon_fan_target: +if (!val)/* no unlimited target speed */ +return -EINVAL ; + reg =AMC6821_REG_TACH_SETTINGL ; +break ; +default : +return -EOPNOTSUPP ; + } + + val = val ?6000000 /clamp_val (val,1 ,6000000 ) :0 ; + val =clamp_val (val,0 ,0xffff ); + + regs[0 ] = val &0xff ; + regs[1 ] = val >>8 ; + +return regmap_bulk_write (data->regmap, reg, regs,2 ); } static ssize_t temp_auto_point_temp_show(struct device *dev,
@@ -572,134 +653,9 @@ static ssize_t pwm1_auto_point_pwm_store(struct device *dev,return count; } -static ssize_t fan_show (struct device *dev,struct device_attribute *devattr, -char *buf) -{ -struct amc6821_data *data =dev_get_drvdata (dev); -int ix =to_sensor_dev_attr (devattr)->index; -u32 regval; -u8 regs[2 ]; -int err; - - err =regmap_bulk_read (data->regmap, fan_reg_low[ix], regs,2 ); -if (err) -return err; - regval = (regs[1 ] <<8 ) | regs[0 ]; - -return sysfs_emit (buf,"%d\n" ,6000000 / (regval ? :1 )); -} - -static ssize_t fan1_fault_show (struct device *dev, -struct device_attribute *devattr,char *buf) -{ -struct amc6821_data *data =dev_get_drvdata (dev); -u32 regval; -int err; - - err =regmap_read (data->regmap,AMC6821_REG_STAT1 , ®val); -if (err) -return err; - -return sysfs_emit (buf,"%d\n" , !!(regval &AMC6821_STAT1_FANS )); -} - -static ssize_t fan_store (struct device *dev,struct device_attribute *attr, -const char *buf,size_t count) -{ -struct amc6821_data *data =dev_get_drvdata (dev); -int ix =to_sensor_dev_attr (attr)->index; -unsigned long val; -u8 regs[2 ]; -int err; - - err =kstrtoul (buf,10 , &val); -if (err) -return err; - -/* Minimum and target fan speed must not be unlimited (0) */ -if ((ix ==IDX_FAN1_MIN || ix ==IDX_FAN1_TARGET ) && !val) -return -EINVAL ; - - val = val >0 ?6000000 /clamp_val (val,1 ,6000000 ) :0 ; - val =clamp_val (val,0 ,0xFFFF ); - - regs[0 ] = val &0xff ; - regs[1 ] = val >>8 ; - - err =regmap_bulk_write (data->regmap, fan_reg_low[ix], regs,2 ); -if (err) -return err; - -return count; -} - -static ssize_t fan1_pulses_show (struct device *dev, -struct device_attribute *devattr,char *buf) -{ -struct amc6821_data *data =dev_get_drvdata (dev); -u32 regval; -int err; - - err =regmap_read (data->regmap,AMC6821_REG_CONF4 , ®val); -if (err) -return err; - -return sysfs_emit (buf,"%d\n" , (regval &AMC6821_CONF4_PSPR ) ?4 :2 ); -} - -static ssize_t fan1_pulses_store (struct device *dev, -struct device_attribute *attr,const char *buf, -size_t count) -{ -struct amc6821_data *data =dev_get_drvdata (dev); -long val; -int err; - - err =kstrtol (buf,10 , &val); -if (err) -return err; - -if (val !=2 && val !=4 ) -return -EINVAL ; - - err =regmap_update_bits (data->regmap,AMC6821_REG_CONF4 , -AMC6821_CONF4_PSPR , - val ==4 ?AMC6821_CONF4_PSPR :0 ); -if (err) -return err; - -return count; -} - -static SENSOR_DEVICE_ATTR_RO(temp1_input, temp, IDX_TEMP1_INPUT); -static SENSOR_DEVICE_ATTR_RW(temp1_min, temp, IDX_TEMP1_MIN); -static SENSOR_DEVICE_ATTR_RW(temp1_max, temp, IDX_TEMP1_MAX); -static SENSOR_DEVICE_ATTR_RW(temp1_crit, temp, IDX_TEMP1_CRIT); -static SENSOR_DEVICE_ATTR_RO(temp1_min_alarm, temp_alarm, IDX_TEMP1_MIN); -static SENSOR_DEVICE_ATTR_RO(temp1_max_alarm, temp_alarm, IDX_TEMP1_MAX); -static SENSOR_DEVICE_ATTR_RO(temp1_crit_alarm, temp_alarm, IDX_TEMP1_CRIT); -static SENSOR_DEVICE_ATTR_RO(temp2_input, temp, IDX_TEMP2_INPUT); -static SENSOR_DEVICE_ATTR_RW(temp2_min, temp, IDX_TEMP2_MIN); -static SENSOR_DEVICE_ATTR_RW(temp2_max, temp, IDX_TEMP2_MAX); -static SENSOR_DEVICE_ATTR_RW(temp2_crit, temp, IDX_TEMP2_CRIT); -static SENSOR_DEVICE_ATTR_RO(temp2_fault, temp2_fault, 0); -static SENSOR_DEVICE_ATTR_RO(temp2_min_alarm, temp_alarm, IDX_TEMP2_MIN); -static SENSOR_DEVICE_ATTR_RO(temp2_max_alarm, temp_alarm, IDX_TEMP2_MAX); -static SENSOR_DEVICE_ATTR_RO(temp2_crit_alarm, temp_alarm, IDX_TEMP2_CRIT); -static SENSOR_DEVICE_ATTR_RO(fan1_input, fan, IDX_FAN1_INPUT); -static SENSOR_DEVICE_ATTR_RW(fan1_min, fan, IDX_FAN1_MIN); -static SENSOR_DEVICE_ATTR_RW(fan1_max, fan, IDX_FAN1_MAX); -static SENSOR_DEVICE_ATTR_RW(fan1_target, fan, IDX_FAN1_TARGET); -static SENSOR_DEVICE_ATTR_RO(fan1_fault, fan1_fault, 0); -static SENSOR_DEVICE_ATTR_RW(fan1_pulses, fan1_pulses, 0); - -static SENSOR_DEVICE_ATTR_RW(pwm1, pwm1, 0); -static SENSOR_DEVICE_ATTR_RW(pwm1_enable, pwm1_enable, 0); static SENSOR_DEVICE_ATTR_RO(pwm1_auto_point1_pwm, pwm1_auto_point_pwm, 0); static SENSOR_DEVICE_ATTR_RW(pwm1_auto_point2_pwm, pwm1_auto_point_pwm, 1); static SENSOR_DEVICE_ATTR_RO(pwm1_auto_point3_pwm, pwm1_auto_point_pwm, 2); -static SENSOR_DEVICE_ATTR_RO(pwm1_auto_channels_temp, pwm1_auto_channels_temp, - 0); static SENSOR_DEVICE_ATTR_2_RO(temp1_auto_point1_temp, temp_auto_point_temp, 1, 0); static SENSOR_DEVICE_ATTR_2_RW(temp1_auto_point2_temp, temp_auto_point_temp,
@@ -715,30 +671,6 @@ static SENSOR_DEVICE_ATTR_2_RW(temp2_auto_point3_temp, temp_auto_point_temp, 2, 2);static struct attribute *amc6821_attrs[] = { - &sensor_dev_attr_temp1_input.dev_attr.attr, - &sensor_dev_attr_temp1_min.dev_attr.attr, - &sensor_dev_attr_temp1_max.dev_attr.attr, - &sensor_dev_attr_temp1_crit.dev_attr.attr, - &sensor_dev_attr_temp1_min_alarm.dev_attr.attr, - &sensor_dev_attr_temp1_max_alarm.dev_attr.attr, - &sensor_dev_attr_temp1_crit_alarm.dev_attr.attr, - &sensor_dev_attr_temp2_input.dev_attr.attr, - &sensor_dev_attr_temp2_min.dev_attr.attr, - &sensor_dev_attr_temp2_max.dev_attr.attr, - &sensor_dev_attr_temp2_crit.dev_attr.attr, - &sensor_dev_attr_temp2_min_alarm.dev_attr.attr, - &sensor_dev_attr_temp2_max_alarm.dev_attr.attr, - &sensor_dev_attr_temp2_crit_alarm.dev_attr.attr, - &sensor_dev_attr_temp2_fault.dev_attr.attr, - &sensor_dev_attr_fan1_input.dev_attr.attr, - &sensor_dev_attr_fan1_min.dev_attr.attr, - &sensor_dev_attr_fan1_max.dev_attr.attr, - &sensor_dev_attr_fan1_target.dev_attr.attr, - &sensor_dev_attr_fan1_fault.dev_attr.attr, - &sensor_dev_attr_fan1_pulses.dev_attr.attr, - &sensor_dev_attr_pwm1.dev_attr.attr, - &sensor_dev_attr_pwm1_enable.dev_attr.attr, - &sensor_dev_attr_pwm1_auto_channels_temp.dev_attr.attr, &sensor_dev_attr_pwm1_auto_point1_pwm.dev_attr.attr, &sensor_dev_attr_pwm1_auto_point2_pwm.dev_attr.attr, &sensor_dev_attr_pwm1_auto_point3_pwm.dev_attr.attr,
@@ -750,13 +682,117 @@ static struct attribute *amc6821_attrs[] = { &sensor_dev_attr_temp2_auto_point3_temp.dev_attr.attr,NULL }; -ATTRIBUTE_GROUPS (amc6821); +static int amc6821_read (struct device *dev,enum hwmon_sensor_types type, +u32 attr,int channel,long *val) +{ +switch (type) { +case hwmon_temp: +return amc6821_temp_read (dev, attr, channel, val); +case hwmon_fan: +return amc6821_fan_read (dev, attr, val); +case hwmon_pwm: +return amc6821_pwm_read (dev, attr, val); +default : +return -EOPNOTSUPP ; + } +} + +static int amc6821_write (struct device *dev,enum hwmon_sensor_types type, +u32 attr,int channel,long val) +{ +switch (type) { +case hwmon_temp: +return amc6821_temp_write (dev, attr, channel, val); +case hwmon_fan: +return amc6821_fan_write (dev, attr, val); +case hwmon_pwm: +return amc6821_pwm_write (dev, attr, val); +default : +return -EOPNOTSUPP ; + } +} + +static umode_t amc6821_is_visible (const void *data, +enum hwmon_sensor_types type, +u32 attr,int channel) +{ +switch (type) { +case hwmon_temp: +switch (attr) { +case hwmon_temp_input: +case hwmon_temp_min_alarm: +case hwmon_temp_max_alarm: +case hwmon_temp_crit_alarm: +case hwmon_temp_fault: +return 0444 ; +case hwmon_temp_min: +case hwmon_temp_max: +case hwmon_temp_crit: +return 0644 ; +default : +return 0 ; + } +case hwmon_fan: +switch (attr) { +case hwmon_fan_input: +case hwmon_fan_fault: +return 0444 ; +case hwmon_fan_pulses: +case hwmon_fan_min: +case hwmon_fan_max: +case hwmon_fan_target: +return 0644 ; +default : +return 0 ; + } +case hwmon_pwm: +switch (attr) { +case hwmon_pwm_enable: +case hwmon_pwm_input: +return 0644 ; +case hwmon_pwm_auto_channels_temp: +return 0444 ; +default : +return 0 ; + } +default : +return 0 ; + } +} + +static const struct hwmon_channel_info *const amc6821_info[] = { +HWMON_CHANNEL_INFO (temp, +HWMON_T_INPUT |HWMON_T_MIN |HWMON_T_MAX | +HWMON_T_CRIT |HWMON_T_MIN_ALARM | +HWMON_T_MAX_ALARM |HWMON_T_CRIT_ALARM , +HWMON_T_INPUT |HWMON_T_MIN |HWMON_T_MAX | +HWMON_T_CRIT |HWMON_T_MIN_ALARM | +HWMON_T_MAX_ALARM |HWMON_T_CRIT_ALARM | +HWMON_T_FAULT ), +HWMON_CHANNEL_INFO (fan, +HWMON_F_INPUT |HWMON_F_MIN |HWMON_F_MAX | +HWMON_F_TARGET |HWMON_F_PULSES |HWMON_F_FAULT ), +HWMON_CHANNEL_INFO (pwm, +HWMON_PWM_INPUT |HWMON_PWM_ENABLE | +HWMON_PWM_AUTO_CHANNELS_TEMP ), +NULL +}; + +static const struct hwmon_ops amc6821_hwmon_ops = { + .is_visible = amc6821_is_visible, + .read = amc6821_read, + .write = amc6821_write, +}; + +static const struct hwmon_chip_info amc6821_chip_info = { + .ops = &amc6821_hwmon_ops, + .info = amc6821_info, +}; +/* Return 0 if detection is successful, -ENODEV otherwise */ -static int amc6821_detect ( -struct i2c_client *client, -struct i2c_board_info *info) +static int amc6821_detect (struct i2c_client *client,struct i2c_board_info *info) {struct i2c_adapter *adapter = client->adapter;int address = client->addr;
@@ -879,9 +915,9 @@ static int amc6821_probe(struct i2c_client *client)if (err)return err; - hwmon_dev =devm_hwmon_device_register_with_groups (dev, client->name, - data, - amc6821_groups); + hwmon_dev =devm_hwmon_device_register_with_info (dev, client->name, + data, &amc6821_chip_info, + amc6821_groups);return PTR_ERR_OR_ZERO (hwmon_dev); }
Signature · 1 line
2.39.2
Re: [PATCH v2 10/11] hwmon: (amc6821) Convert to with_info API
Hi Guenter,
Quoted 6 lines · Guenter Roeck
Convert to use
with_infoAPI to simplify the code and make it easier to maintain. This also reduces code size by approximately 20%.No functional change intended.
Signed-off-by Guenter Roeck <[email protected]>
Looks good to me,
Thanks!
Quentin
Guenter Roeck
maintainerPATCH v2 11/11 hwmon: (amc6821) Add support for pwm1_mode attribute
In reply to Guenter RoeckAMC6821 supports configuring if a fan is DC or PWM controlled. Add support for the pwm1_mode attribute to make it runtime configurable.
---
v2: New patch
Documentation/hwmon/amc6821.rst | 1 + drivers/hwmon/amc6821.c | 16 +++++++++++++++- 2 files changed, 16 insertions(+), 1 deletion(-)
Documentation/hwmon/amc6821.rst +1 -0
@@ -58,6 +58,7 @@ pwm1_enable rw regulator mode, 1=open loop, 2=fan controlled remote-sensor temperature, 4=fan controlled by target rpm set with fan1_target attribute. +pwm1_mode rw Fan duty control mode (0=DC, 1=PWM) pwm1_auto_channels_temp ro 1 if pwm_enable==2, 3 if pwm_enable==3 pwm1_auto_point1_pwm ro Hardwired to 0, shared for both temperature channels.
drivers/hwmon/amc6821.c +15 -1
@@ -317,6 +317,12 @@ static int amc6821_pwm_read(struct device *dev, u32 attr, long *val)break ; }return 0 ; +case hwmon_pwm_mode: + err =regmap_read (regmap,AMC6821_REG_CONF2 , ®val); +if (err) +return err; + *val = !!(regval &AMC6821_CONF2_TACH_MODE ); +return 0 ;case hwmon_pwm_auto_channels_temp: err =regmap_read (regmap,AMC6821_REG_CONF1 , ®val);if (err)
@@ -372,6 +378,13 @@ static int amc6821_pwm_write(struct device *dev, u32 attr, long val)return regmap_update_bits (regmap,AMC6821_REG_CONF1 ,AMC6821_CONF1_FDRC0 |AMC6821_CONF1_FDRC1 , mode); +case hwmon_pwm_mode: +if (val <0 || val >1 ) +return -EINVAL ; +return regmap_update_bits (regmap,AMC6821_REG_CONF1 , +AMC6821_CONF2_TACH_MODE , + val ?AMC6821_CONF2_TACH_MODE :0 ); +break ;case hwmon_pwm_input:if (val <0 || val >255 )return -EINVAL ;
@@ -749,6 +762,7 @@ static umode_t amc6821_is_visible(const void *data, }case hwmon_pwm:switch (attr) { +case hwmon_pwm_mode:case hwmon_pwm_enable:case hwmon_pwm_input:return 0644 ;
@@ -775,7 +789,7 @@ static const struct hwmon_channel_info * const amc6821_info[] = {HWMON_F_INPUT |HWMON_F_MIN |HWMON_F_MAX | HWMON_F_TARGET | HWMON_F_PULSES | HWMON_F_FAULT),HWMON_CHANNEL_INFO (pwm, -HWMON_PWM_INPUT |HWMON_PWM_ENABLE | +HWMON_PWM_INPUT |HWMON_PWM_ENABLE |HWMON_PWM_MODE |HWMON_PWM_AUTO_CHANNELS_TEMP ), NULL };
Signature · 1 line
2.39.2
Re: [PATCH v2 11/11] hwmon: (amc6821) Add support for pwm1_mode attribute
Hi Guenter,
Quoted 41 lines · Guenter Roeck
AMC6821 supports configuring if a fan is DC or PWM controlled. Add support for the
pwm1_modeattribute to make it runtime configurable.Signed-off-by Guenter Roeck <[email protected]>---
v2: New patchDocumentation/hwmon/amc6821.rst | 1 + drivers/hwmon/amc6821.c | 16 +++++++++++++++- 2 files changed, 16 insertions(+), 1 deletion(-)Documentation/hwmon/amc6821.rst +1
-0@@ -58,6 +58,7 @@ pwm1_enable rw regulator mode, 1=open loop, 2=fan controlled remote-sensor temperature, 4=fan controlled by target rpm set with fan1_target attribute. +pwm1_mode rw Fan duty control mode (0=DC, 1=PWM) pwm1_auto_channels_temp ro 1 if pwm_enable==2, 3 if pwm_enable==3 pwm1_auto_point1_pwm ro Hardwired to 0, shared for both temperature channels.drivers/hwmon/amc6821.c +6
-0@@ -317,6 +317,12 @@ static int amc6821_pwm_read(struct device *dev, u32 attr, long *val)break ; }return 0 ; +case hwmon_pwm_mode: + err =regmap_read (regmap,AMC6821_REG_CONF2 , ®val); +if (err) +return err; + *val = !!(regval &AMC6821_CONF2_TACH_MODE ); +return 0 ;case hwmon_pwm_auto_channels_temp: err =regmap_read (regmap,AMC6821_REG_CONF1 , ®val);if (err)
drivers/hwmon/amc6821.c static int amc6821_pwm_write(struct device *dev, u32 attr, long val) · line 384
Quoted 7 lines
drivers/hwmon/amc6821.c +4
-0@@ -372,6 +378,13 @@ static int amc6821_pwm_write(struct device *dev, u32 attr, long val)return regmap_update_bits (regmap,AMC6821_REG_CONF1 ,AMC6821_CONF1_FDRC0 |AMC6821_CONF1_FDRC1 , mode); +case hwmon_pwm_mode: +if (val <0 || val >1 ) +return -EINVAL ; + return regmap_update_bits(regmap, AMC6821_REG_CONF1,
Wrong register here, should be AMC6821_REG_CONF2.
Otherwise, looks good to me.
Cheers,
Quentin
Guenter Roeck
maintainerRe: [PATCH v2 11/11] hwmon: (amc6821) Add support for pwm1_mode attribute
Quoted 45 lines · Quentin Schulz
Hi Guenter,
Quoted 42 lines · Guenter Roeck
AMC6821 supports configuring if a fan is DC or PWM controlled. Add support for the
pwm1_modeattribute to make it runtime configurable.Signed-off-by Guenter Roeck <[email protected]>---
v2: New patch
Documentation/hwmon/amc6821.rst| 1 + drivers/hwmon/amc6821.c | 16 +++++++++++++++-2 files changed, 16 insertions(+), 1 deletion(-)Documentation/hwmon/amc6821.rst +0
-0@@ -58,6 +58,7 @@ pwm1_enable rw regulator mode, 1=open loop, 2=fan controlled remote-sensor temperature,4=fan controlled by target rpm set with
fan1_targetattribute.
+pwm1_mode rw Fan duty control mode (0=DC, 1=PWM)pwm1_auto_channels_tempro 1 if pwm_enable==2, 3 if pwm_enable==3 pwm1_auto_point1_pwm ro Hardwired to 0, shared for both temperature channels.drivers/hwmon/amc6821.c +6
-0@@ -317,6 +317,12 @@ static int amc6821_pwm_read(struct device *dev, u32 attr, long *val) break; } return 0; + case hwmon_pwm_mode: + err = regmap_read(regmap, AMC6821_REG_CONF2, ®val); + if (err) + return err; + *val = !!(regval & AMC6821_CONF2_TACH_MODE); + return 0;case
hwmon_pwm_auto_channels_temp:
err =regmap_read(regmap, AMC6821_REG_CONF1, ®val); if (err)drivers/hwmon/amc6821.c +0
-0@@ -372,6 +378,13 @@ static int amc6821_pwm_write(struct device *dev, u32 attr, long val) return regmap_update_bits(regmap, AMC6821_REG_CONF1,
Quoted 9 lines
drivers/hwmon/amc6821.c static int amc6821_pwm_write(struct device *dev, u32 attr, long val) · line 384
Quoted 6 lines
drivers/hwmon/amc6821.c +4
-0AMC6821_CONF1_FDRC0 | AMC6821_CONF1_FDRC1, mode); + case hwmon_pwm_mode: + if (val < 0 || val > 1) + return -EINVAL; + return regmap_update_bits(regmap, AMC6821_REG_CONF1,Wrong register here, should be
AMC6821_REG_CONF2.
Oops. I had a bug in my test script, and thanks to that it failed to report the problem.
Thanks for noticing!
Guenter