wireless-regdb: Update regulatory info for New Zealand (NZ) for 2022
PATCH 1/5 wireless-regdb: Update regulatory info for New Zealand (NZ) for 2022
From: Ping-Ke Shih <[email protected]>
Radiocommunications Regulations (General User Radio Licence for Short Range Devices) Notice 2022 listed spectrum:
2400.0000 - 2483.5000
* e.i.r.p. 0 dBW (1 W)
5150.0000 - 5350.0000
* the maximum power is 0 dBW (1 W) e.i.r.p. and
the maximum permitted power spectral density is -13 dBW/MHz (17 dBm/Hz, 50 mW/MHz) e.i.r.p.
* 5250 - 5350 MHz, If Transmitter Power Control is not used, then the maximum power (e.i.r.p.) value shall be reduced by 3 dB.
5470.0000 - 5725.0000
* 5470 - 5725 MHz, transmitter peak power must not exceed -6 dBW (250 mW) If Transmitter Power Control is not used, then the maximum power (e.i.r.p.) value must be reduced by 3 dB.
5725.0000 - 5850.0000
* 5725 - 5850 MHz, the transmitter peak power must not exceed 0 dBW (1 W) and the power spectral density must not exceed 17 dBm/MHz.
5925.0000 - 6425.0000
* the maximum power is -6 dBW (24 dBm, 250 mW ) e.i.r.p. and the maximum permitted power spectral density is -19 dBW/MHz (11 dBm/MHz, 12.6 mW/MHz) e.i.r.p. for low power devices. Only be used indoors.
* the maximum power is -16 dBW (14 dBm, 25 mW ) e.i.r.p. and the maximum permitted power spectral density is -29 dBW/MHz (1 dBm/MHz, 1.26 mW/MHz) e.i.r.p. for very low power devices. Very Low Power applications.
57000.0000 - 71000.0000
* for devices transmitting at 10 dBW e.i.r.p or less,
the power spectral density must not exceed -7 dBW/MHz e.i.r.p. and the maximum transmit power must not exceed -3 dBW at the antenna port or ports.
* for devices transmitting greater than 10 dBW e.i.r.p., the power spectral density shall not exceed 8 dBW/MHz e.i.r.p and antennas with a gain greater than 30 dBi shall be used.
[1] https://gazette.govt.nz/notice/id/2022-go3100
--- db.txt | 14 +++++++++----- 1 file changed, 9 insertions(+), 5 deletions(-)
db.txt +9 -5
@@ -1416,12 +1416,16 @@ country NP: DFS-JP (5250 - 5330 @ 80), (20), DFS, AUTO-BW (5735 - 5835 @ 80), (20) +# Source: +# https://gazette.govt.nz/notice/id/2022-go3100 country NZ: DFS-ETSI - (2402 - 2482 @ 40), (30) - (5170 - 5250 @ 80), (17), AUTO-BW - (5250 - 5330 @ 80), (24), DFS, AUTO-BW - (5490 - 5730 @ 160), (24), DFS - (5735 - 5835 @ 80), (30) + (2400 - 2483.5 @ 40), (30) + (5150 - 5250 @ 80), (30), AUTO-BW + (5250 - 5350 @ 80), (27), DFS, AUTO-BW + (5470 - 5730 @ 160), (21), DFS + (5725 - 5850 @ 80), (30) + (5925 - 6425 @ 320), (24), NO-OUTDOOR + (57000 - 71000 @ 2160), (40) country OM: DFS-ETSI (2402 - 2482 @ 40), (20)
Signature · 1 line
2.25.1
PATCH 2/5 wireless-regdb: Update regulatory info for Peru (PE) on 6GHz
From: Ping-Ke Shih <[email protected]>
Ministerial Resolution -2021-MTC/01 decided
For the band 5925-7125 MHz, low power indoor case of use.
- access point
maximum EIRP: 30 dBm
Limited power spectral density: 5 dBm / MHz
- user devices
maximum EIRP: 24 dBm
Limited power spectral density: -1 dBm / MHz
--- db.txt | 3 +++ 1 file changed, 3 insertions(+)
db.txt +3 -0
@@ -1443,12 +1443,15 @@ country PA: DFS-FCC (5725 - 5850 @ 80), (36) (57000 - 64000 @ 2160), (43) +# Source: +# https://cdn.www.gob.pe/uploads/document/file/1861732/Resoluci%C3%B3n%20Ministerial%20nro%20373-2021-MTC/01.pdf country PE: DFS-FCC (2402 - 2482 @ 40), (20) (5170 - 5250 @ 80), (17), AUTO-BW (5250 - 5330 @ 80), (24), DFS, AUTO-BW (5490 - 5730 @ 160), (24), DFS (5735 - 5835 @ 80), (30) + (5925 - 7125 @ 320), (12), NO-OUTDOOR country PF: DFS-ETSI (2402 - 2482 @ 40), (20)
Signature · 1 line
2.25.1
Re: [PATCH 2/5] wireless-regdb: Update regulatory info for Peru (PE) on 6GHz
Quoted 5 lines · Ping-Ke Shih
From: Ping-Ke Shih <[email protected]>
Ministerial Resolution -2021-MTC/01 decided
Quoted 7 lines
For the band 5925-7125 MHz, low power indoor case of use.
- access point
maximum EIRP: 30 dBm
Limited power spectral density: 5 dBm / MHz
- user devices
maximum EIRP: 24 dBm
Limited power spectral density: -1 dBm / MHz
Please explicitly mention that the PSD limits the rule to 12 dBm.
Otherwise this looks good.
ChenYu
Quoted 30 lines
Signed-off-by Ping-Ke Shih <[email protected]>--- db.txt | 3 +++ 1 file changed, 3 insertions(+)db.txt +3
-1@@ -1443,12 +1443,15 @@ country PA: DFS-FCC (5725 - 5850 @ 80), (36) (57000 - 64000 @ 2160), (43) +# Source: +# https://cdn.www.gob.pe/uploads/document/file/1861732/Resoluci%C3%B3n%20Ministerial%20nro%20373-2021-MTC/01.pdf country PE: DFS-FCC (2402 - 2482 @ 40), (20) (5170 - 5250 @ 80), (17), AUTO-BW (5250 - 5330 @ 80), (24), DFS, AUTO-BW (5490 - 5730 @ 160), (24), DFS (5735 - 5835 @ 80), (30) + (5925 - 7125 @ 320), (12), NO-OUTDOOR country PF: DFS-ETSI (2402 - 2482 @ 40), (20) --2.25.1
PATCH 3/5 wireless-regdb: Update regulatory info for Qatar (QA) on 6GHz
In reply to Ping-Ke ShihFrom: Ping-Ke Shih <[email protected]>
Communications Regulatory Authority, State of Qatar, released Class License for the use of RLAN devices over 5925-6425 MHz Band on 26 April 2022 [2] via page [1].
Technical Requirements for the use of RLAN Devices over 5925-6425MHz
- Low Power
* e.i.r.p 23 dBm
* Indoor Use only
- Very Low Power
* e.i.r.p 14 dBm
* Indoor and Outdoor Use
[1] https://www.cra.gov.qa/en/document/class-license-for-the-use-of-rlan-devices-over-5925-6425-mhz-band
[2] https://www.cra.gov.qa/-/media/System/D/2/5/8/D258CF18B83A5613B0D590193CB799CB/Class-License-WIFI-6E-Final-English-032022--V3.ashx
--- db.txt | 3 +++ 1 file changed, 3 insertions(+)
db.txt +3 -0
@@ -1559,12 +1559,15 @@ country PY: DFS-FCC (5490 - 5730 @ 160), (24), DFS (5735 - 5835 @ 80), (30) +# Source: +# https://www.cra.gov.qa/-/media/System/D/2/5/8/D258CF18B83A5613B0D590193CB799CB/Class-License-WIFI-6E-Final-English-032022--V3.ashx country QA: DFS-ETSI (2400 - 2483.5 @ 40), (100 mW), NO-OUTDOOR (5150 - 5250 @ 80), (200 mW), NO-OUTDOOR, AUTO-BW (5250 - 5350 @ 80), (200 mW), NO-OUTDOOR, DFS, AUTO-BW (5470 - 5725 @ 160), (100 mW), NO-OUTDOOR, DFS (5725 - 5875 @ 80), (100 mW), NO-OUTDOOR, DFS + (5925 - 6425 @ 320), (23), NO-OUTDOOR (57000 - 66000 @ 2160), (40), NO-OUTDOOR country RE: DFS-ETSI
Signature · 1 line
2.25.1
Chen-Yu Tsai
AppliedRe: [PATCH 3/5] wireless-regdb: Update regulatory info for Qatar (QA) on 6GHz
Quoted 12 lines · Ping-Ke Shih
Communications Regulatory Authority, State of Qatar, released Class License for the use of RLAN devices over 5925-6425 MHz Band on 26 April 2022 [2] via page [1].
Technical Requirements for the use of RLAN Devices over 5925-6425MHz
- Low Power
* e.i.r.p 23 dBm
* Indoor Use only
- Very Low Power
* e.i.r.p 14 dBm
* Indoor and Outdoor Use
Quoted 1 line
[...]
Applied to master in wens/wireless-regdb.git, thanks!
[3/5] wireless-regdb: Update regulatory info for Qatar (QA) on 6GHz
https://git.kernel.org/wens/wireless-regdb/c/c7d1083bc5c1
Best regards,
Signature · 1 line
Chen-Yu Tsai <[email protected]>
PATCH 4/5 wireless-regdb: Update regulatory info for El Salvador (SV) on 6GHz
In reply to Ping-Ke ShihFrom: Ping-Ke Shih <[email protected]>
The General Superintendency of Electricity and Telecommunications Makes Knowledge to the General issued resolution No. T-0408-2023.
Free use within the entire band for WLAN (WiFi) application, from 5925 MHz to 7125 MHz, must have following technical and operation conditions:
- access point
* P.I.R.E 30 dBm
* spectral density of P.I.R.E. 5 dBm/Mhz
- client
* P.I.R.E 24 dBm
* spectral density of P.I.R.E. -1 dBm/Mhz
- Indoor use only permitted
[1] https://www.siget.gob.sv/actualizacion-de-cuadro-nacional-de-atribucion-de-frecuencias-t-0408-2023/
--- db.txt | 3 +++ 1 file changed, 3 insertions(+)
db.txt +3 -0
@@ -1736,11 +1736,14 @@ country SR: DFS-ETSI (5250 - 5330 @ 80), (20), DFS, AUTO-BW (5490 - 5710 @ 160), (27), DFS +# Source: +# https://www.siget.gob.sv/actualizacion-de-cuadro-nacional-de-atribucion-de-frecuencias-t-0408-2023/ country SV: DFS-FCC (2402 - 2482 @ 40), (20) (5170 - 5250 @ 20), (17) (5250 - 5330 @ 20), (23), DFS (5735 - 5835 @ 20), (30) + (5925 - 7125 @ 320), (12), NO-OUTDOOR country SY: (2402 - 2482 @ 40), (20)
Signature · 1 line
2.25.1
Re: [PATCH 4/5] wireless-regdb: Update regulatory info for El Salvador (SV) on 6GHz
Quoted 6 lines · Ping-Ke Shih
From: Ping-Ke Shih <[email protected]>
The General Superintendency of Electricity and Telecommunications Makes Knowledge to the General issued resolution No. T-0408-2023.
Quoted 10 lines
Free use within the entire band for WLAN (WiFi) application, from 5925 MHz to 7125 MHz, must have following technical and operation conditions:
- access point
* P.I.R.E 30 dBm
* spectral density of P.I.R.E. 5 dBm/Mhz
- client
* P.I.R.E 24 dBm
* spectral density of P.I.R.E. -1 dBm/Mhz
- Indoor use only permitted
Please explicitly mention that the PSD limits the rule to 12 dBm.
ChenYu
Quoted 29 lines
[1] https://www.siget.gob.sv/actualizacion-de-cuadro-nacional-de-atribucion-de-frecuencias-t-0408-2023/
Signed-off-by Ping-Ke Shih <[email protected]>--- db.txt | 3 +++ 1 file changed, 3 insertions(+)db.txt +3
-1@@ -1736,11 +1736,14 @@ country SR: DFS-ETSI (5250 - 5330 @ 80), (20), DFS, AUTO-BW (5490 - 5710 @ 160), (27), DFS +# Source: +# https://www.siget.gob.sv/actualizacion-de-cuadro-nacional-de-atribucion-de-frecuencias-t-0408-2023/ country SV: DFS-FCC (2402 - 2482 @ 40), (20) (5170 - 5250 @ 20), (17) (5250 - 5330 @ 20), (23), DFS (5735 - 5835 @ 20), (30) + (5925 - 7125 @ 320), (12), NO-OUTDOOR country SY: (2402 - 2482 @ 40), (20) --2.25.1
PATCH 5/5 wireless-regdb: Update regulatory info for Togo (TG) for 2022
In reply to Ping-Ke ShihFrom: Ping-Ke Shih <[email protected]>
Republic ToGolaise released Decision N 226/ARCEP/DG/22.
2400-2483.5 MHz
- EIRP 100 mW and 10 mW/MHz density
5150-5350 MHz
- EIRP 200 mW
- If TPC is not used, must be reduced by 3 dB
5470-5850 MHz
- EIRP 1W
- If TPC is not used, must be reduced by 3 dB
5925-6425 MHz
- LPI
* EIRP 23 dBm (200 mW)
* EIRP density 10 dBm/MHz
* Use limited to indoor
- VLP
* EIRP 14 dBm (25 mW)
* EIRP density -1 dBm/MHz
57-66 GHz
- EIRP 40 dBm and 13 dBm/MHz density
--- db.txt | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-)
db.txt +8 -4
@@ -1763,11 +1763,15 @@ country TD: DFS-ETSI (5250 - 5330 @ 80), (20), DFS, AUTO-BW (5490 - 5710 @ 160), (27), DFS +# Source: +# https://arcep.tg/wp-content/uploads/2022/12/Decision-226-22-Determinant-les-categories-et-conditions-techniques-dexploitation-des-appareils-de-faible-puissance-et-de-faible-portee.pdf country TG: DFS-ETSI - (2402 - 2482 @ 40), (20) - (5170 - 5250 @ 40), (20) - (5250 - 5330 @ 40), (20), DFS - (5490 - 5710 @ 40), (27), DFS + (2400 - 2483.5 @ 40), (100 mW) + (5150 - 5250 @ 40), (200 mW) + (5250 - 5350 @ 40), (20), DFS + (5470 - 5850 @ 40), (27), DFS + (5925 - 6425 @ 320), (23), NO-OUTDOOR + (57000 - 66000 @2160), (40) # Source: # https://ratchakitcha.soc.go.th/documents/140D100S0000000004000.pdf
Signature · 1 line
2.25.1
Re: [PATCH 5/5] wireless-regdb: Update regulatory info for Togo (TG) for 2022
Quoted 5 lines · Ping-Ke Shih
From: Ping-Ke Shih <[email protected]>
Republic ToGolaise released Decision N 226/ARCEP/DG/22.
Quoted 12 lines
2400-2483.5 MHz
- EIRP 100 mW and 10 mW/MHz density
5150-5350 MHz
- EIRP 200 mW
- If TPC is not used, must be reduced by 3 dB
5470-5850 MHz
- EIRP 1W
- If TPC is not used, must be reduced by 3 dB
5925-6425 MHz
- LPI
* EIRP 23 dBm (200 mW)
* EIRP density 10 dBm/MHz
The document you linked to suggests it is actually -10 dBm/MHz, which kind of makes it useless as the total e.i.r.p for a 20 MHz channel would be 2 mW or 3 dBm...
And the PSD for LP being lower than VLP seems like an error.
Quoted 22 lines
* Use limited to indoor
- VLP
* EIRP 14 dBm (25 mW)
* EIRP density -1 dBm/MHz
57-66 GHz
- EIRP 40 dBm and 13 dBm/MHz densitySigned-off-by Ping-Ke Shih <[email protected]>--- db.txt | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-)db.txt +0
-0@@ -1763,11 +1763,15 @@ country TD: DFS-ETSI (5250 - 5330 @ 80), (20), DFS, AUTO-BW (5490 - 5710 @ 160), (27), DFS
db.txt country TD: DFS-ETSI · line 1771
Quoted 10 lines
db.txt +5
-4+# Source: +# https://arcep.tg/wp-content/uploads/2022/12/Decision-226-22-Determinant-les-categories-et-conditions-techniques-dexploitation-des-appareils-de-faible-puissance-et-de-faible-portee.pdf country TG: DFS-ETSI - (2402 - 2482 @ 40), (20) - (5170 - 5250 @ 40), (20) - (5250 - 5330 @ 40), (20), DFS - (5490 - 5710 @ 40), (27), DFS + (2400 - 2483.5 @ 40), (100 mW) + (5150 - 5250 @ 40), (200 mW) + (5250 - 5350 @ 40), (20), DFS
The regulation doesn't say this can be split. It's one rule for 5150 - 5350.
db.txt country TD: DFS-ETSI · line 1772
Quoted 1 line
db.txt +1
-0+ (5470 - 5850 @ 40), (27), DFS
Why only 40 MHz channels?
db.txt country TD: DFS-ETSI · line 1774
Quoted 2 lines
db.txt +2
-0+ (5925 - 6425 @ 320), (23), NO-OUTDOOR + (57000 - 66000 @2160), (40)
Regulation requires DFS on all bands.
ChenYu
Quoted 5 lines
db.txt +0
-1# Source: # https://ratchakitcha.soc.go.th/documents/140D100S0000000004000.pdf --2.25.1
Re: [PATCH 5/5] wireless-regdb: Update regulatory info for Togo (TG) for 2022
Quoted 8 lines · Chen-Yu Tsai
Quoted 5 lines · Ping-Ke Shih
5925-6425 MHz
- LPI
* EIRP 23 dBm (200 mW)
* EIRP density 10 dBm/MHz
Quoted 5 lines
The document you linked to suggests it is actually -10 dBm/MHz, which kind of makes it useless as the total e.i.r.p for a 20 MHz channel would be 2 mW or 3 dBm...
And the PSD for LP being lower than VLP seems like an error.
Since it looks like an error, I keep the power limit as I made, but add some description by v2.
Thanks for the review.
Ping-Ke
Quoted 8 lines · Ping-Ke Shih
From: Ping-Ke Shih <[email protected]>
Radiocommunications Regulations (General User Radio Licence for Short Range Devices) Notice 2022 listed spectrum:
2400.0000 - 2483.5000
* e.i.r.p. 0 dBW (1 W)
13. Transmitters using e.i.r.p. greater than 0 dBW (1 W) must employ frequency hopping or digital modulation techniques.
AFAIK WiFi uses digital modulation techniques. So this could be raised up to 6 dBW?
Quoted 11 lines
5150.0000 - 5350.0000
* the maximum power is 0 dBW (1 W) e.i.r.p. and
the maximum permitted power spectral density is -13 dBW/MHz (17 dBm/Hz, 50 mW/MHz) e.i.r.p.
* 5250 - 5350 MHz, If Transmitter Power Control is not used, then the maximum power (e.i.r.p.) value shall be reduced by 3 dB.5470.0000 - 5725.0000
* 5470 - 5725 MHz, transmitter peak power must not exceed -6 dBW (250 mW) If Transmitter Power Control is not used, then the maximum power (e.i.r.p.) value must be reduced by 3 dB.
We use e.i.r.p. value in the database. The limit is 1W, then minus 3 dB due to lack of TPC.
Quoted 3 lines
5725.0000 - 5850.0000
* 5725 - 5850 MHz, the transmitter peak power must not exceed 0 dBW (1 W) and the power spectral density must not exceed 17 dBm/MHz.
13. Transmitters using e.i.r.p. greater than 0 dBW (1 W) must employ frequency hopping or digital modulation techniques.
AFAIK WiFi uses digital modulation techniques. So this could be raised up to 6 dBW?
Thanks
ChenYu
Quoted 55 lines
5925.0000 - 6425.0000
* the maximum power is -6 dBW (24 dBm, 250 mW ) e.i.r.p. and the maximum permitted power spectral density is -19 dBW/MHz (11 dBm/MHz, 12.6 mW/MHz) e.i.r.p. for low power devices. Only be used indoors.
* the maximum power is -16 dBW (14 dBm, 25 mW ) e.i.r.p. and the maximum permitted power spectral density is -29 dBW/MHz (1 dBm/MHz, 1.26 mW/MHz) e.i.r.p. for very low power devices. Very Low Power applications.57000.0000 - 71000.0000
* for devices transmitting at 10 dBW e.i.r.p or less,
the power spectral density must not exceed -7 dBW/MHz e.i.r.p. and the maximum transmit power must not exceed -3 dBW at the antenna port or ports.
* for devices transmitting greater than 10 dBW e.i.r.p., the power spectral density shall not exceed 8 dBW/MHz e.i.r.p and antennas with a gain greater than 30 dBi shall be used.[1] https://gazette.govt.nz/notice/id/2022-go3100
Signed-off-by Ping-Ke Shih <[email protected]>--- db.txt | 14 +++++++++----- 1 file changed, 9 insertions(+), 5 deletions(-)db.txt +9
-6@@ -1416,12 +1416,16 @@ country NP: DFS-JP (5250 - 5330 @ 80), (20), DFS, AUTO-BW (5735 - 5835 @ 80), (20) +# Source: +# https://gazette.govt.nz/notice/id/2022-go3100 country NZ: DFS-ETSI - (2402 - 2482 @ 40), (30) - (5170 - 5250 @ 80), (17), AUTO-BW - (5250 - 5330 @ 80), (24), DFS, AUTO-BW - (5490 - 5730 @ 160), (24), DFS - (5735 - 5835 @ 80), (30) + (2400 - 2483.5 @ 40), (30) + (5150 - 5250 @ 80), (30), AUTO-BW + (5250 - 5350 @ 80), (27), DFS, AUTO-BW + (5470 - 5730 @ 160), (21), DFS + (5725 - 5850 @ 80), (30) + (5925 - 6425 @ 320), (24), NO-OUTDOOR + (57000 - 71000 @ 2160), (40) country OM: DFS-ETSI (2402 - 2482 @ 40), (20) --2.25.1