Skip to contentSkip to conversation

net: dsa: vsc73xx: fix MDIO bus access and PHY operations

PATCH Superseded Pawel Dembicki 2 participants 8 messages Aug 5, 2024 – Aug 8, 2024

Subsystems (4)

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

v2 cover net: dsa: vsc73xx: fix MDIO bus access and PHY operations

This series are extracted patches from net-next series [0].

The VSC73xx driver has issues with PHY configuration. This patch series fixes most of them.

The first patch synchronizes the register configuration routine with the datasheet recommendations.

Patches 2-3 restore proper communication on the MDIO bus. Currently, the write value isn't sent to the MDIO register, and without a busy check, communication with the PHY can be interrupted. This causes the PHY to receive improper configuration and autonegotiation could fail.

The fourth patch removes the PHY reset blockade, as it is no longer required.

After fixing the MDIO operations, autonegotiation became possible. The last patch removes the blockade, which became unnecessary after the MDIO operations fix. It also enables the MDI-X feature, which is disabled by default in forced 100BASE-TX mode like other Vitesse PHYs.

[0] https://patchwork.kernel.org/project/netdevbpf/list/?series=874739&state=%2A&archive=both

Pawel Dembicki (5):
net: dsa: vsc73xx: fix port MAC configuration in full duplex mode
net: dsa: vsc73xx: pass value in phy_write operation
net: dsa: vsc73xx: check busy flag in MDIO operations
net: dsa: vsc73xx: allow phy resetting
net: phy: vitesse: repair vsc73xx autonegotiation

 drivers/net/dsa/vitesse-vsc73xx-core.c | 57 +++++++++++++++++++-------
 drivers/net/phy/vitesse.c              | 25 ++++++++---
 2 files changed, 62 insertions(+), 20 deletions(-)
Signature · 1 line
2.34.1
#1 lore raw

PATCH v2 1/5 net: dsa: vsc73xx: fix port MAC configuration in full duplex mode

According to the datasheet description ("Port Mode Procedure" in 5.6.2), the VSC73XX_MAC_CFG_WEXC_DIS bit is configured only for half duplex mode.

The WEXC_DIS bit is responsible for MAC behavior after an excessive collision. Let's set it as described in the datasheet.

Fixes 05bd97fc559d ("net: dsa: Add Vitesse VSC73xx DSA router driver")

---
v2:
- Added 'Fixes' and 'Reviewed-by' to commit message.

This patch came from net-next series[0].
Changes since net-next:
- rebased to netdev/main only

[0] https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/

---
 drivers/net/dsa/vitesse-vsc73xx-core.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/net/dsa/vitesse-vsc73xx-core.c +5 -1
index d9d3e30fd47a..f548ed4cb23f 100644
@@ -957,6 +957,11 @@ static void vsc73xx_mac_link_up(struct phylink_config *config,
 
 	if (duplex == DUPLEX_FULL)
 		val |= VSC73XX_MAC_CFG_FDX;
+	else
+		/* In datasheet description ("Port Mode Procedure" in 5.6.2)
+		 * this bit is configured only for half duplex.
+		 */
+		val |= VSC73XX_MAC_CFG_WEXC_DIS;
 
 	/* This routine is described in the datasheet (below ARBDISC register
 	 * description)
@@ -967,7 +972,6 @@ static void vsc73xx_mac_link_up(struct phylink_config *config,
 	get_random_bytes(&seed, 1);
 	val |= seed << VSC73XX_MAC_CFG_SEED_OFFSET;
 	val |= VSC73XX_MAC_CFG_SEED_LOAD;
-	val |= VSC73XX_MAC_CFG_WEXC_DIS;
 
 	/* Those bits are responsible for MTU only. Kernel takes care about MTU,
 	 * let's enable +8 bytes frame length unconditionally.
Signature · 1 line
2.34.1
#2 lore raw

PATCH v2 2/5 net: dsa: vsc73xx: pass value in phy_write operation

In reply to Pawel Dembicki

In the 'vsc73xx_phy_write' function, the register value is missing, and the phy write operation always sends zeros.

This commit passes the value variable into the proper register.

Fixes 05bd97fc559d ("net: dsa: Add Vitesse VSC73xx DSA router driver")

---
v2:
- Fixed 'Fixes' and added 'Reviewed-by' to commit message

This patch came from net-next series[0].
Changes since net-next:
- rebased to netdev/main only

[0] https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/

---
 drivers/net/dsa/vitesse-vsc73xx-core.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/dsa/vitesse-vsc73xx-core.c +1 -1
index f548ed4cb23f..4b300c293dec 100644
@@ -574,7 +574,7 @@ static int vsc73xx_phy_write(struct dsa_switch *ds, int phy, int regnum,
 		return 0;
 	}
 
-	cmd = (phy << 21) | (regnum << 16);
+	cmd = (phy << 21) | (regnum << 16) | val;
 	ret = vsc73xx_write(vsc, VSC73XX_BLOCK_MII, 0, 1, cmd);
 	if (ret)
 		return ret;
Signature · 1 line
2.34.1
#3 lore raw

PATCH v2 3/5 net: dsa: vsc73xx: check busy flag in MDIO operations

In reply to Pawel Dembicki

The VSC73xx has a busy flag used during MDIO operations. It is raised when MDIO read/write operations are in progress. Without it, PHYs are misconfigured and bus operations do not work as expected.

Fixes 05bd97fc559d ("net: dsa: Add Vitesse VSC73xx DSA router driver")

---
v2:
- used defines from patch moved to net-next

This patch came from net-next series[0].
Changes since net-next:
- removed mutex
- used method poll.h to poll busy value in 'vsc73xx_mdio_busy_check'
- use 'vsc73xx_mdio_busy_check' for control if mdio is ready

[0] https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/

---
 drivers/net/dsa/vitesse-vsc73xx-core.c | 40 ++++++++++++++++++++++++--
 1 file changed, 38 insertions(+), 2 deletions(-)
drivers/net/dsa/vitesse-vsc73xx-core.c +38 -2
index 4b300c293dec..a9378e0512d8 100644
@@ -40,6 +40,10 @@
 #define VSC73XX_BLOCK_ARBITER	0x5 /* Only subblock 0 */
 #define VSC73XX_BLOCK_SYSTEM	0x7 /* Only subblock 0 */
 
+/* MII Block subblock */
+#define VSC73XX_BLOCK_MII_INTERNAL	0x0 /* Internal MDIO subblock */
+#define VSC73XX_BLOCK_MII_EXTERNAL	0x1 /* External MDIO subblock */
+
 #define CPU_PORT	6 /* CPU port */
 
 /* MAC Block registers */
@@ -225,6 +229,8 @@
 #define VSC73XX_MII_CMD		0x1
 #define VSC73XX_MII_DATA	0x2
 
+#define VSC73XX_MII_STAT_BUSY	BIT(3)
+
 /* Arbiter block 5 registers */
 #define VSC73XX_ARBEMPTY		0x0c
 #define VSC73XX_ARBDISC			0x0e
@@ -299,6 +305,7 @@
 #define IS_739X(a) (IS_7395(a) || IS_7398(a))
 
 #define VSC73XX_POLL_SLEEP_US		1000
+#define VSC73XX_MDIO_POLL_SLEEP_US	5
 #define VSC73XX_POLL_TIMEOUT_US		10000
 
 struct vsc73xx_counter {
@@ -527,6 +534,22 @@ static int vsc73xx_detect(struct vsc73xx *vsc)
 	return 0;
 }
 
+static int vsc73xx_mdio_busy_check(struct vsc73xx *vsc)
+{
+	int ret, err;
+	u32 val;
+
+	ret = read_poll_timeout(vsc73xx_read, err,
+				err < 0 || !(val & VSC73XX_MII_STAT_BUSY),
+				VSC73XX_MDIO_POLL_SLEEP_US,
+				VSC73XX_POLL_TIMEOUT_US, false, vsc,
+				VSC73XX_BLOCK_MII, VSC73XX_BLOCK_MII_INTERNAL,
+				VSC73XX_MII_STAT, &val);
+	if (ret)
+		return ret;
+	return err;
+}
+
 static int vsc73xx_phy_read(struct dsa_switch *ds, int phy, int regnum)
 {
 	struct vsc73xx *vsc = ds->priv;
@@ -534,13 +557,22 @@ static int vsc73xx_phy_read(struct dsa_switch *ds, int phy, int regnum)
 	u32 val;
 	int ret;
 
+	ret = vsc73xx_mdio_busy_check(vsc);
+	if (ret)
+		return ret;
+
 	/* Setting bit 26 means "read" */
 	cmd = BIT(26) | (phy << 21) | (regnum << 16);
 	ret = vsc73xx_write(vsc, VSC73XX_BLOCK_MII, 0, 1, cmd);
 	if (ret)
 		return ret;
-	msleep(2);
+
+	ret = vsc73xx_mdio_busy_check(vsc);
+	if (ret)
+		return ret;
+
 	ret = vsc73xx_read(vsc, VSC73XX_BLOCK_MII, 0, 2, &val);
+
 	if (ret)
 		return ret;
 	if (val & BIT(16)) {
@@ -561,7 +593,11 @@ static int vsc73xx_phy_write(struct dsa_switch *ds, int phy, int regnum,
 {
 	struct vsc73xx *vsc = ds->priv;
 	u32 cmd;
-	int ret;
+	int ret = 0;
+
+	ret = vsc73xx_mdio_busy_check(vsc);
+	if (ret)
+		return ret;
 
 	/* It was found through tedious experiments that this router
 	 * chip really hates to have it's PHYs reset. They
Signature · 1 line
2.34.1
maintainer
#4 lore raw

Re: [PATCH net v2 3/5] net: dsa: vsc73xx: check busy flag in MDIO operations

drivers/net/dsa/vitesse-vsc73xx-core.c static int vsc73xx_phy_read(struct dsa_switch *ds, int phy, int regnum) · line 576

Quoted 9 lines · On Mon, 5 Aug 2024 23:10:29 +0200 Pawel Dembicki wrote:
drivers/net/dsa/vitesse-vsc73xx-core.c +6 -1
-	msleep(2);
+
+	ret = vsc73xx_mdio_busy_check(vsc);
+	if (ret)
+		return ret;
+
 	ret = vsc73xx_read(vsc, VSC73XX_BLOCK_MII, 0, 2, &val);
+
 	if (ret)

nit: why the empty line between call and error check?

drivers/net/dsa/vitesse-vsc73xx-core.c static int vsc73xx_phy_write(struct dsa_switch *ds, int phy, int regnum, · line 598

Quoted 10 lines
drivers/net/dsa/vitesse-vsc73xx-core.c +3 -1
 		return ret;
 	if (val & BIT(16)) {
@@ -561,7 +593,11 @@ static int vsc73xx_phy_write(struct dsa_switch *ds, int phy, int regnum,
 {
 	struct vsc73xx *vsc = ds->priv;
 	u32 cmd;
-	int ret;
+	int ret = 0;
+
+	ret = vsc73xx_mdio_busy_check(vsc);

nit: why init ret to 0 ?

#5 lore raw

PATCH v2 4/5 net: dsa: vsc73xx: allow phy resetting

In reply to Pawel Dembicki

Resetting the VSC73xx PHY was problematic because the MDIO bus, without a busy check, read and wrote incorrect register values.

My investigation indicates that resetting the PHY only triggers changes in configuration. However, improper register values written earlier were only exposed after a soft reset.

The reset itself wasn't the issue; rather, the problem stemmed from incorrect read and write operations.

A 'soft_reset' can now proceed normally. There are no reasons to keep the VSC73xx from being reset.

This commit removes the reset blockade in the 'vsc73xx_phy_write' function.

---
v2:
- improved commit description

This patch came from net-next series[0].
Changes since net-next:
- rebased to netdev/main only

[0] https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/

---
 drivers/net/dsa/vitesse-vsc73xx-core.c | 11 -----------
 1 file changed, 11 deletions(-)
drivers/net/dsa/vitesse-vsc73xx-core.c +0 -11
index a9378e0512d8..ac02927a153b 100644
@@ -599,17 +599,6 @@ static int vsc73xx_phy_write(struct dsa_switch *ds, int phy, int regnum,
 	if (ret)
 		return ret;
 
-	/* It was found through tedious experiments that this router
-	 * chip really hates to have it's PHYs reset. They
-	 * never recover if that happens: autonegotiation stops
-	 * working after a reset. Just filter out this command.
-	 * (Resetting the whole chip is OK.)
-	 */
-	if (regnum == 0 && (val & BIT(15))) {
-		dev_info(vsc->dev, "reset PHY - disallowed\n");
-		return 0;
-	}
-
 	cmd = (phy << 21) | (regnum << 16) | val;
 	ret = vsc73xx_write(vsc, VSC73XX_BLOCK_MII, 0, 1, cmd);
 	if (ret)
Signature · 1 line
2.34.1
#6 lore raw

PATCH v2 5/5 net: phy: vitesse: repair vsc73xx autonegotiation

In reply to Pawel Dembicki

When the vsc73xx mdio bus work properly, the generic autonegotiation configuration works well.

Vsc73xx have auto MDI-X disabled by default in forced mode. This commit enables it.

---
This patch came from net-next series[0].
Changes since net-next:
- rebased to netdev/main only

[0] https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/

---
 drivers/net/phy/vitesse.c | 25 +++++++++++++++++++------
 1 file changed, 19 insertions(+), 6 deletions(-)
drivers/net/phy/vitesse.c +19 -6
index 897b979ec03c..19b7bf189be5 100644
@@ -60,6 +60,11 @@
 /* Vitesse Extended Page Access Register */
 #define MII_VSC82X4_EXT_PAGE_ACCESS	0x1f
 
+/* VSC73XX PHY_BYPASS_CTRL register*/
+#define MII_VSC73XX_PHY_BYPASS_CTRL		MII_DCOUNTER
+#define MII_PBC_FORCED_SPEED_AUTO_MDIX_DIS	BIT(7)
+#define MII_VSC73XX_PBC_AUTO_NP_EXCHANGE_DIS	BIT(1)
+
 /* Vitesse VSC8601 Extended PHY Control Register 1 */
 #define MII_VSC8601_EPHY_CTL		0x17
 #define MII_VSC8601_EPHY_CTL_RGMII_SKEW	(1 << 8)
@@ -239,12 +244,20 @@ static int vsc739x_config_init(struct phy_device *phydev)
 
 static int vsc73xx_config_aneg(struct phy_device *phydev)
 {
-	/* The VSC73xx switches does not like to be instructed to
-	 * do autonegotiation in any way, it prefers that you just go
-	 * with the power-on/reset defaults. Writing some registers will
-	 * just make autonegotiation permanently fail.
-	 */
-	return 0;
+	int ret;
+
+	/* Enable Auto MDI-X in forced 10/100 mode */
+	if (phydev->autoneg != AUTONEG_ENABLE && phydev->speed <= SPEED_100) {
+		ret = genphy_setup_forced(phydev);
+
+		if (ret < 0) /* error */
+			return ret;
+
+		return phy_clear_bits(phydev, MII_VSC73XX_PHY_BYPASS_CTRL,
+				      MII_PBC_FORCED_SPEED_AUTO_MDIX_DIS);
+	}
+
+	return genphy_config_aneg(phydev);
 }
 
 /* This adds a skew for both TX and RX clocks, so the skew should only be
Signature · 1 line
2.34.1
maintainer
#7 lore raw

Re: [PATCH net v2 5/5] net: phy: vitesse: repair vsc73xx autonegotiation

Quoted 5 lines · On Mon, 5 Aug 2024 23:10:31 +0200 Pawel Dembicki wrote:

When the vsc73xx mdio bus work properly, the generic autonegotiation configuration works well.

Vsc73xx have auto MDI-X disabled by default in forced mode. This commit enables it.

This feels a bit like net-next material. Never worked, so it's more new feature than a fix.