Skip to contentSkip to conversation

Bluetooth: btrtl: Add the support for RTL8922A

PATCH RESEND Superseded [email protected] 3 participants 4 messages Aug 20, 2024 – Aug 21, 2024 1 message not in the archive Bluetooth drivers

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

PATCH RESEND v2 1/1 Bluetooth: btrtl: Add the support for RTL8922A

From: Max Chou <[email protected]>

Add the support for RTL8922A BT controller on USB interface. The necessary firmware will be submitted to linux-firmware project.

The device info from /sys/kernel/debug/usb/devices as below.

T:  Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0bda ProdID=8922 Rev= 0.00
S:  Manufacturer=Realtek
S:  Product=Bluetooth Radio
S:  SerialNumber=00E04C885A01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms

---
change:
v2: edit commit log

---
 drivers/bluetooth/btrtl.c | 16 ++++++++++++++++
 drivers/bluetooth/btusb.c | 13 +++++++++++++
 2 files changed, 29 insertions(+)
drivers/bluetooth/btrtl.c +16 -0
index f2f37143c454..555c2964ec1b 100644
@@ -30,6 +30,7 @@
 #define RTL_ROM_LMP_8822B	0x8822
 #define RTL_ROM_LMP_8852A	0x8852
 #define RTL_ROM_LMP_8851B	0x8851
+#define RTL_ROM_LMP_8922A	0x8922
 #define RTL_CONFIG_MAGIC	0x8723ab55
 
 #define RTL_VSC_OP_COREDUMP	0xfcff
@@ -69,6 +70,7 @@ enum btrtl_chip_id {
 	CHIP_ID_8852B = 20,
 	CHIP_ID_8852C = 25,
 	CHIP_ID_8851B = 36,
+	CHIP_ID_8922A = 44,
 	CHIP_ID_8852BT = 47,
 };
 
@@ -309,6 +311,15 @@ static const struct id_table ic_id_table[] = {
 	  .cfg_name = "rtl_bt/rtl8851bu_config",
 	  .hw_info  = "rtl8851bu" },
 
+	/* 8922A */
+	{ IC_INFO(RTL_ROM_LMP_8922A, 0xa, 0xc, HCI_USB),
+	  .config_needed = false,
+	  .has_rom_version = true,
+	  .has_msft_ext = true,
+	  .fw_name  = "rtl_bt/rtl8922au_fw",
+	  .cfg_name = "rtl_bt/rtl8922au_config",
+	  .hw_info  = "rtl8922au" },
+
 	/* 8852BT/8852BE-VT */
 	{ IC_INFO(RTL_ROM_LMP_8852A, 0x87, 0xc, HCI_USB),
 	  .config_needed = false,
@@ -655,6 +666,7 @@ static int rtlbt_parse_firmware(struct hci_dev *hdev,
 		{ RTL_ROM_LMP_8852A, 20 },	/* 8852B */
 		{ RTL_ROM_LMP_8852A, 25 },	/* 8852C */
 		{ RTL_ROM_LMP_8851B, 36 },	/* 8851B */
+		{ RTL_ROM_LMP_8922A, 44 },	/* 8922A */
 		{ RTL_ROM_LMP_8852A, 47 },	/* 8852BT */
 	};
 
@@ -1255,6 +1267,7 @@ int btrtl_download_firmware(struct hci_dev *hdev,
 	case RTL_ROM_LMP_8852A:
 	case RTL_ROM_LMP_8703B:
 	case RTL_ROM_LMP_8851B:
+	case RTL_ROM_LMP_8922A:
 		err = btrtl_setup_rtl8723b(hdev, btrtl_dev);
 		break;
 	default:
@@ -1286,6 +1299,7 @@ void btrtl_set_quirks(struct hci_dev *hdev, struct btrtl_device_info *btrtl_dev)
 	case CHIP_ID_8852B:
 	case CHIP_ID_8852C:
 	case CHIP_ID_8851B:
+	case CHIP_ID_8922A:
 	case CHIP_ID_8852BT:
 		set_bit(HCI_QUIRK_VALID_LE_STATES, &hdev->quirks);
 		set_bit(HCI_QUIRK_WIDEBAND_SPEECH_SUPPORTED, &hdev->quirks);
@@ -1529,3 +1543,5 @@ MODULE_FIRMWARE("rtl_bt/rtl8852btu_config.bin");
 MODULE_FIRMWARE("rtl_bt/rtl8852cu_fw.bin");
 MODULE_FIRMWARE("rtl_bt/rtl8852cu_fw_v2.bin");
 MODULE_FIRMWARE("rtl_bt/rtl8852cu_config.bin");
+MODULE_FIRMWARE("rtl_bt/rtl8922au_fw.bin");
+MODULE_FIRMWARE("rtl_bt/rtl8922au_config.bin");
drivers/bluetooth/btusb.c +13 -0
index acdba5d77694..8f931cfbac11 100644
@@ -540,6 +540,8 @@ static const struct usb_device_id quirks_table[] = {
 						     BTUSB_WIDEBAND_SPEECH },
 	{ USB_DEVICE(0x13d3, 0x3592), .driver_info = BTUSB_REALTEK |
 						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x0489, 0xe122), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
 
 	/* Realtek 8852BE Bluetooth devices */
 	{ USB_DEVICE(0x0cb8, 0xc559), .driver_info = BTUSB_REALTEK |
@@ -564,6 +566,17 @@ static const struct usb_device_id quirks_table[] = {
 	/* Realtek 8852BT/8852BE-VT Bluetooth devices */
 	{ USB_DEVICE(0x0bda, 0x8520), .driver_info = BTUSB_REALTEK |
 						     BTUSB_WIDEBAND_SPEECH },
+
+	/* Realtek 8922AE Bluetooth devices */
+	{ USB_DEVICE(0x0bda, 0x8922), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x13d3, 0x3617), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x13d3, 0x3616), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x0489, 0xe130), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+
 	/* Realtek Bluetooth devices */
 	{ USB_VENDOR_AND_INTERFACE_INFO(0x0bda, 0xe0, 0x01, 0x01),
 	  .driver_info = BTUSB_REALTEK },
Signature · 1 line
2.25.1
#1 lore raw

Dear Max,

Thank you for your patch.

Am 20.08.24 um 07:16 schrieb [email protected]:

Quoted 1 line

From: Max Chou <[email protected]>

The article *the* in the commit message summary is uncommon. Maybe:

Add support for RTL8922A

Quoted 1 line

Add the support for RTL8922A BT controller on USB interface.

Ditto.

Quoted 1 line

The necessary firmware will be submitted to linux-firmware project.

Maybe add the firmware file name rtl8922au_fw?

If you could also document the device you tested with, that means which has that Bluetooth controller, that might be good to know too.

Quoted 67 lines

The device info from /sys/kernel/debug/usb/devices as below.

T:  Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0bda ProdID=8922 Rev= 0.00
S:  Manufacturer=Realtek
S:  Product=Bluetooth Radio
S:  SerialNumber=00E04C885A01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms

---
change:
v2: edit commit log

---
  drivers/bluetooth/btrtl.c | 16 ++++++++++++++++
  drivers/bluetooth/btusb.c | 13 +++++++++++++
  2 files changed, 29 insertions(+)
drivers/bluetooth/btrtl.c +2 -0
index f2f37143c454..555c2964ec1b 100644
@@ -30,6 +30,7 @@
  #define RTL_ROM_LMP_8822B	0x8822
  #define RTL_ROM_LMP_8852A	0x8852
  #define RTL_ROM_LMP_8851B	0x8851
+#define RTL_ROM_LMP_8922A	0x8922
  #define RTL_CONFIG_MAGIC	0x8723ab55
 
  #define RTL_VSC_OP_COREDUMP	0xfcff
@@ -69,6 +70,7 @@ enum btrtl_chip_id {
  	CHIP_ID_8852B = 20,
  	CHIP_ID_8852C = 25,
  	CHIP_ID_8851B = 36,
+	CHIP_ID_8922A = 44,
  	CHIP_ID_8852BT = 47,
  };
 
@@ -309,6 +311,15 @@ static const struct id_table ic_id_table[] = {
  	  .cfg_name = "rtl_bt/rtl8851bu_config",
  	  .hw_info  = "rtl8851bu" },

drivers/bluetooth/btrtl.c static const struct id_table ic_id_table[] = { · line 322

Quoted 10 lines
drivers/bluetooth/btrtl.c +9 -0
 
+	/* 8922A */
+	{ IC_INFO(RTL_ROM_LMP_8922A, 0xa, 0xc, HCI_USB),
+	  .config_needed = false,
+	  .has_rom_version = true,
+	  .has_msft_ext = true,
+	  .fw_name  = "rtl_bt/rtl8922au_fw",
+	  .cfg_name = "rtl_bt/rtl8922au_config",
+	  .hw_info  = "rtl8922au" },
+

Why not sort it?

Quoted 20 lines
drivers/bluetooth/btrtl.c +2 -0
  	/* 8852BT/8852BE-VT */
  	{ IC_INFO(RTL_ROM_LMP_8852A, 0x87, 0xc, HCI_USB),
  	  .config_needed = false,
@@ -655,6 +666,7 @@ static int rtlbt_parse_firmware(struct hci_dev *hdev,
  		{ RTL_ROM_LMP_8852A, 20 },	/* 8852B */
  		{ RTL_ROM_LMP_8852A, 25 },	/* 8852C */
  		{ RTL_ROM_LMP_8851B, 36 },	/* 8851B */
+		{ RTL_ROM_LMP_8922A, 44 },	/* 8922A */
  		{ RTL_ROM_LMP_8852A, 47 },	/* 8852BT */
  	};
 
@@ -1255,6 +1267,7 @@ int btrtl_download_firmware(struct hci_dev *hdev,
  	case RTL_ROM_LMP_8852A:
  	case RTL_ROM_LMP_8703B:
  	case RTL_ROM_LMP_8851B:
+	case RTL_ROM_LMP_8922A:
  		err = btrtl_setup_rtl8723b(hdev, btrtl_dev);
  		break;
  	default:

drivers/bluetooth/btrtl.c void btrtl_set_quirks(struct hci_dev *hdev, struct btrtl_device_info *btrtl_dev) · line 1303

Quoted 5 lines
drivers/bluetooth/btrtl.c +1 -0
@@ -1286,6 +1299,7 @@ void btrtl_set_quirks(struct hci_dev *hdev, struct btrtl_device_info *btrtl_dev)
  	case CHIP_ID_8852B:
  	case CHIP_ID_8852C:
  	case CHIP_ID_8851B:
+	case CHIP_ID_8922A:
  	case CHIP_ID_8852BT:

Why not sort it?

Quoted 13 lines
drivers/bluetooth/btrtl.c +2 -0
  		set_bit(HCI_QUIRK_VALID_LE_STATES, &hdev->quirks);
  		set_bit(HCI_QUIRK_WIDEBAND_SPEECH_SUPPORTED, &hdev->quirks);
@@ -1529,3 +1543,5 @@ MODULE_FIRMWARE("rtl_bt/rtl8852btu_config.bin");
  MODULE_FIRMWARE("rtl_bt/rtl8852cu_fw.bin");
  MODULE_FIRMWARE("rtl_bt/rtl8852cu_fw_v2.bin");
  MODULE_FIRMWARE("rtl_bt/rtl8852cu_config.bin");
+MODULE_FIRMWARE("rtl_bt/rtl8922au_fw.bin");
+MODULE_FIRMWARE("rtl_bt/rtl8922au_config.bin");
drivers/bluetooth/btusb.c +0 -0
index acdba5d77694..8f931cfbac11 100644

drivers/bluetooth/btusb.c static const struct usb_device_id quirks_table[] = { · line 544

Quoted 5 lines
drivers/bluetooth/btusb.c +2 -0
@@ -540,6 +540,8 @@ static const struct usb_device_id quirks_table[] = {
  						     BTUSB_WIDEBAND_SPEECH },
  	{ USB_DEVICE(0x13d3, 0x3592), .driver_info = BTUSB_REALTEK |
  						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x0489, 0xe122), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },

Why not sort it?

Quoted 5 lines
drivers/bluetooth/btusb.c +0 -0
  	/* Realtek 8852BE Bluetooth devices */
  	{ USB_DEVICE(0x0cb8, 0xc559), .driver_info = BTUSB_REALTEK |
@@ -564,6 +566,17 @@ static const struct usb_device_id quirks_table[] = {
  	/* Realtek 8852BT/8852BE-VT Bluetooth devices */

drivers/bluetooth/btusb.c static const struct usb_device_id quirks_table[] = { · line 576

Quoted 10 lines
drivers/bluetooth/btusb.c +8 -0
  	{ USB_DEVICE(0x0bda, 0x8520), .driver_info = BTUSB_REALTEK |
  						     BTUSB_WIDEBAND_SPEECH },
+
+	/* Realtek 8922AE Bluetooth devices */
+	{ USB_DEVICE(0x0bda, 0x8922), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x13d3, 0x3617), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+	{ USB_DEVICE(0x13d3, 0x3616), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },

Why not sort it?

Quoted 6 lines
drivers/bluetooth/btusb.c +3 -0
+	{ USB_DEVICE(0x0489, 0xe130), .driver_info = BTUSB_REALTEK |
+						     BTUSB_WIDEBAND_SPEECH },
+
  	/* Realtek Bluetooth devices */
  	{ USB_VENDOR_AND_INTERFACE_INFO(0x0bda, 0xe0, 0x01, 0x01),
  	  .driver_info = BTUSB_REALTEK },
#2 lore raw
In reply to [email protected]

This is an automated email and please do not reply to this email.

Dear Submitter,

Thank you for submitting the patches to the linux bluetooth mailing list.
While preparing the CI tests, the patches you submitted couldn't be applied to the current HEAD of the repository.

----- Output -----

error: patch failed: drivers/bluetooth/btrtl.c:1286
error: drivers/bluetooth/btrtl.c: patch does not apply
error: patch failed: drivers/bluetooth/btusb.c:540
error: drivers/bluetooth/btusb.c: patch does not apply
hint: Use 'git am --show-current-patch' to see the failed patch

Please resolve the issue and submit the patches again.

---
Regards,
Linux Bluetooth

A message that is not in the archive (sent off-list or not yet received): [email protected]

author
#4 lore raw

Hi! Paul,
Thanks for your feedback.
I just send the V3 to fix auto build error because I did not rebase for the previous patch. Please check my comment for the questions. Thanks.

Quoted 17 lines

-----Original Message-----
From: Paul Menzel [mailto:[email protected]]
Sent: Tuesday, August 20, 2024 1:37 PM
To: Max Chou <[email protected]>
Cc: Marcel Holtmann <[email protected]>; Luiz Augusto von Dentz <[email protected]>; [email protected]; [email protected]; Hilda Wu <[email protected]>; [email protected]; KidmanLee <[email protected]>; Karen Hsu <[email protected]>
Subject: Re: [PATCH V2 RESEND] Bluetooth: btrtl: Add the support for RTL8922A

External mail.

Quoted 8 lines

Dear Max,

Thank you for your patch.

Am 20.08.24 um 07:16 schrieb [email protected]:

Quoted 1 line

From: Max Chou <[email protected]>

There're some different chips in RTL8922A series.
RTL8922AE and RTL8922AU are BT USB I/F, and this patch was committed for that. RTL8922AE-VR is BT UART I/F.
I think " RTL8922A BT controller on USB interface." is more common. There is the same description for the past patch as well.

Quoted 10 lines

The article *the* in the commit message summary is uncommon. Maybe:

Add support for RTL8922A

Quoted 1 line

Add the support for RTL8922A BT controller on USB interface.

Ditto.

Quoted 1 line

The necessary firmware will be submitted to linux-firmware project.

For USB I/F, Realtek assigns the FW filename as rtlXXXXXu_fw.bin. When this patch is merged, I will submit the FW file to linux-firmware.

Quoted 73 lines

Maybe add the firmware file name rtl8922au_fw?

If you could also document the device you tested with, that means which has that Bluetooth controller, that might be good to know too.

Quoted 68 lines

The device info from /sys/kernel/debug/usb/devices as below.

T:  Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0bda ProdID=8922 Rev= 0.00
S:  Manufacturer=Realtek
S:  Product=Bluetooth Radio
S:  SerialNumber=00E04C885A01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms

---
change:
v2: edit commit log

---
  drivers/bluetooth/btrtl.c | 16 ++++++++++++++++
  drivers/bluetooth/btusb.c | 13 +++++++++++++
  2 files changed, 29 insertions(+)
drivers/bluetooth/btrtl.c +2 -0
index f2f37143c454..555c2964ec1b 100644
@@ -30,6 +30,7 @@
  #define RTL_ROM_LMP_8822B   0x8822
  #define RTL_ROM_LMP_8852A   0x8852
  #define RTL_ROM_LMP_8851B   0x8851
+#define RTL_ROM_LMP_8922A    0x8922
  #define RTL_CONFIG_MAGIC    0x8723ab55
 
  #define RTL_VSC_OP_COREDUMP 0xfcff
@@ -69,6 +70,7 @@ enum btrtl_chip_id {
      CHIP_ID_8852B = 20,
      CHIP_ID_8852C = 25,
      CHIP_ID_8851B = 36,
+     CHIP_ID_8922A = 44,
      CHIP_ID_8852BT = 47,
  };
 
@@ -309,6 +311,15 @@ static const struct id_table ic_id_table[] = {
        .cfg_name = "rtl_bt/rtl8851bu_config",
        .hw_info  = "rtl8851bu" },
 
Quoted 10 lines

drivers/bluetooth/btrtl.c static const struct id_table ic_id_table[] = { · line 322

Quoted 9 lines
drivers/bluetooth/btrtl.c +9 -0
+     /* 8922A */
+     { IC_INFO(RTL_ROM_LMP_8922A, 0xa, 0xc, HCI_USB),
+       .config_needed = false,
+       .has_rom_version = true,
+       .has_msft_ext = true,
+       .fw_name  = "rtl_bt/rtl8922au_fw",
+       .cfg_name = "rtl_bt/rtl8922au_config",
+       .hw_info  = "rtl8922au" },
+

The chip id is 44 for RTL8922A. I exactly sort it. (between 36 and 47)

Quoted 16 lines

Why not sort it?

drivers/bluetooth/btrtl.c static int rtlbt_parse_firmware(struct hci_dev

Quoted 4 lines
drivers/bluetooth/btrtl.c +0 -0
      /* 8852BT/8852BE-VT */
      { IC_INFO(RTL_ROM_LMP_8852A, 0x87, 0xc, HCI_USB),
        .config_needed = false,
@@ -655,6 +666,7 @@ static int rtlbt_parse_firmware(struct hci_dev

*hdev,

drivers/bluetooth/btrtl.c int btrtl_download_firmware(struct hci_dev

Quoted 8 lines
drivers/bluetooth/btrtl.c +1 -0
              { RTL_ROM_LMP_8852A, 20 },      /* 8852B */
              { RTL_ROM_LMP_8852A, 25 },      /* 8852C */
              { RTL_ROM_LMP_8851B, 36 },      /* 8851B */
+             { RTL_ROM_LMP_8922A, 44 },      /* 8922A */
              { RTL_ROM_LMP_8852A, 47 },      /* 8852BT */
      };
 
@@ -1255,6 +1267,7 @@ int btrtl_download_firmware(struct hci_dev

*hdev,

Quoted 15 lines

drivers/bluetooth/btrtl.c void btrtl_set_quirks(struct hci_dev *hdev, struct

Quoted 8 lines
drivers/bluetooth/btrtl.c +1 -0
      case RTL_ROM_LMP_8852A:
      case RTL_ROM_LMP_8703B:
      case RTL_ROM_LMP_8851B:
+     case RTL_ROM_LMP_8922A:
              err = btrtl_setup_rtl8723b(hdev, btrtl_dev);
              break;
      default:
@@ -1286,6 +1299,7 @@ void btrtl_set_quirks(struct hci_dev *hdev, struct

btrtl_device_info *btrtl_dev)

Quoted 5 lines
drivers/bluetooth/btrtl.c +1 -0
      case CHIP_ID_8852B:
      case CHIP_ID_8852C:
      case CHIP_ID_8851B:
+     case CHIP_ID_8922A:
      case CHIP_ID_8852BT:

In rtlbt_parse_firmware(), chip id 44 is between 36(8851B) and 47(8852BT). Hence, I just followed the sequence here as well.

Quoted 57 lines

Why not sort it?

Quoted 3 lines
drivers/bluetooth/btrtl.c +0 -0
              set_bit(HCI_QUIRK_VALID_LE_STATES, &hdev->quirks);
              set_bit(HCI_QUIRK_WIDEBAND_SPEECH_SUPPORTED,

&hdev->quirks); @@ -1529,3 +1543,5 @@

MODULE_FIRMWARE("rtl_bt/rtl8852btu_config.bin");

drivers/bluetooth/btusb.c static const struct usb_device_id quirks_table[] = { · line 540

Quoted 11 lines
  MODULE_FIRMWARE("rtl_bt/rtl8852cu_fw.bin");
  MODULE_FIRMWARE("rtl_bt/rtl8852cu_fw_v2.bin");
  MODULE_FIRMWARE("rtl_bt/rtl8852cu_config.bin");
drivers/bluetooth/btrtl.c +2 -0
+MODULE_FIRMWARE("rtl_bt/rtl8922au_fw.bin");
+MODULE_FIRMWARE("rtl_bt/rtl8922au_config.bin");
drivers/bluetooth/btusb.c +0 -0
index acdba5d77694..8f931cfbac11 100644
@@ -540,6 +540,8 @@ static const struct usb_device_id quirks_table[] = {
 

BTUSB_WIDEBAND_SPEECH },

drivers/bluetooth/btusb.c static const struct usb_device_id quirks_table[] = { · line 544

Quoted 6 lines
drivers/bluetooth/btusb.c +3 -0
      { USB_DEVICE(0x13d3, 0x3592), .driver_info = BTUSB_REALTEK |
 
 BTUSB_WIDEBAND_SPEECH },
+     { USB_DEVICE(0x0489, 0xe122), .driver_info = BTUSB_REALTEK |
+
+ BTUSB_WIDEBAND_SPEECH },

Why not sort it?

drivers/bluetooth/btusb.c static const struct usb_device_id quirks_table[] = { · line 547

Quoted 3 lines
drivers/bluetooth/btusb.c +0 -0
      /* Realtek 8852BE Bluetooth devices */
      { USB_DEVICE(0x0cb8, 0xc559), .driver_info = BTUSB_REALTEK |

@@

drivers/bluetooth/btusb.c static const struct usb_device_id quirks_table[] = { · line 579

Quoted 9 lines
-564,6 +566,17 @@ static const struct usb_device_id quirks_table[] = {
      /* Realtek 8852BT/8852BE-VT Bluetooth devices */
      { USB_DEVICE(0x0bda, 0x8520), .driver_info = BTUSB_REALTEK |

BTUSB_WIDEBAND_SPEECH },

drivers/bluetooth/btusb.c +4 -0
+
+     /* Realtek 8922AE Bluetooth devices */
+     { USB_DEVICE(0x0bda, 0x8922), .driver_info = BTUSB_REALTEK |
+

BTUSB_WIDEBAND_SPEECH },

drivers/bluetooth/btusb.c static const struct usb_device_id quirks_table[] = { · line 579

Quoted 2 lines
drivers/bluetooth/btusb.c +2 -0
+     { USB_DEVICE(0x13d3, 0x3617), .driver_info = BTUSB_REALTEK |
+

BTUSB_WIDEBAND_SPEECH },

drivers/bluetooth/btusb.c static const struct usb_device_id quirks_table[] = {

Quoted 3 lines
drivers/bluetooth/btusb.c +3 -0
+     { USB_DEVICE(0x13d3, 0x3616), .driver_info = BTUSB_REALTEK |
+
+ BTUSB_WIDEBAND_SPEECH },

Why not sort it?

Quoted 7 lines
drivers/bluetooth/btusb.c +4 -0
+     { USB_DEVICE(0x0489, 0xe130), .driver_info = BTUSB_REALTEK |
+
+ BTUSB_WIDEBAND_SPEECH },
+
      /* Realtek Bluetooth devices */
      { USB_VENDOR_AND_INTERFACE_INFO(0x0bda, 0xe0, 0x01, 0x01),
        .driver_info = BTUSB_REALTEK },