Skip to contentSkip to conversation

mm: override mTHP "enabled" defaults at kernel cmdline

PATCH Applied Barry Song 1 participant 1 message Aug 20, 2024

Subsystems (4)
lore
Share & tools
lore

Barry Song

author
#0 lore raw

PATCH v6 1/1 mm: override mTHP "enabled" defaults at kernel cmdline

From: Ryan Roberts <[email protected]>

Add thp_anon= cmdline parameter to allow specifying the default enablement of each supported anon THP size. The parameter accepts the following format and can be provided multiple times to configure each size:

thp_anon=<size>,<size>[KMG]:<value>;<size>-<size>[KMG]:<value>

An example:

thp_anon=16K-64K:always;128K,512K:inherit;256K:madvise;1M-2M:never

See Documentation/admin-guide/mm/transhuge.rst for more details.

Configuring the defaults at boot time is useful to allow early user space to take advantage of mTHP before its been configured through sysfs.

---
-v6:
* collect acked-by of David, thanks!
* some minor cleanup according to David's comments

 .../admin-guide/kernel-parameters.txt         |  9 ++
 Documentation/admin-guide/mm/transhuge.rst    | 38 +++++--
 mm/huge_memory.c                              | 98 ++++++++++++++++++-
 3 files changed, 137 insertions(+), 8 deletions(-)
Documentation/admin-guide/kernel-parameters.txt +9 -0
index f0057bac20fb..8dd0aefea01e 100644
@@ -6629,6 +6629,15 @@
 			<deci-seconds>: poll all this frequency
 			0: no polling (default)
 
+	thp_anon=	[KNL]
+			Format: <size>,<size>[KMG]:<state>;<size>-<size>[KMG]:<state>
+			state is one of "always", "madvise", "never" or "inherit".
+			Control the default behavior of the system with respect
+			to anonymous transparent hugepages.
+			Can be used multiple times for multiple anon THP sizes.
+			See Documentation/admin-guide/mm/transhuge.rst for more
+			details.
+
 	threadirqs	[KNL,EARLY]
 			Force threading of all interrupt handlers except those
 			marked explicitly IRQF_NO_THREAD.
Documentation/admin-guide/mm/transhuge.rst +31 -7
index 058485daf186..79435c537e21 100644
@@ -284,13 +284,37 @@ that THP is shared. Exceeding the number would block the collapse::
 
 A higher value may increase memory footprint for some workloads.
 
-Boot parameter
-==============
-
-You can change the sysfs boot time defaults of Transparent Hugepage
-Support by passing the parameter ``transparent_hugepage=always`` or
-``transparent_hugepage=madvise`` or ``transparent_hugepage=never``
-to the kernel command line.
+Boot parameters
+===============
+
+You can change the sysfs boot time default for the top-level "enabled"
+control by passing the parameter ``transparent_hugepage=always`` or
+``transparent_hugepage=madvise`` or ``transparent_hugepage=never`` to the
+kernel command line.
+
+Alternatively, each supported anonymous THP size can be controlled by
+passing ``thp_anon=<size>,<size>[KMG]:<state>;<size>-<size>[KMG]:<state>``,
+where ``<size>`` is the THP size (must be a power of 2 of PAGE_SIZE and
+supported anonymous THP)  and ``<state>`` is one of ``always``, ``madvise``,
+``never`` or ``inherit``.
+
+For example, the following will set 16K, 32K, 64K THP to ``always``,
+set 128K, 512K to ``inherit``, set 256K to ``madvise`` and 1M, 2M
+to ``never``::
+
+	thp_anon=16K-64K:always;128K,512K:inherit;256K:madvise;1M-2M:never
+
+``thp_anon=`` may be specified multiple times to configure all THP sizes as
+required. If ``thp_anon=`` is specified at least once, any anon THP sizes
+not explicitly configured on the command line are implicitly set to
+``never``.
+
+``transparent_hugepage`` setting only affects the global toggle. If
+``thp_anon`` is not specified, PMD_ORDER THP will default to ``inherit``.
+However, if a valid ``thp_anon`` setting is provided by the user, the
+PMD_ORDER THP policy will be overridden. If the policy for PMD_ORDER
+is not defined within a valid ``thp_anon``, its policy will default to
+``never``.
 
 Hugepages in tmpfs/shmem
 ========================
mm/huge_memory.c +97 -1

116 lines not on this page · raw message

Signature · 1 line
2.39.3 (Apple Git-146)