mm: override mTHP "enabled" defaults at kernel cmdline
Subsystems (4)
PATCH v6 1/1 mm: override mTHP "enabled" defaults at kernel cmdline
From: Ryan Roberts <[email protected]>
Add thp_anon= cmdline parameter to allow specifying the default enablement of each supported anon THP size. The parameter accepts the following format and can be provided multiple times to configure each size:
thp_anon=<size>,<size>[KMG]:<value>;<size>-<size>[KMG]:<value>
An example:
thp_anon=16K-64K:always;128K,512K:inherit;256K:madvise;1M-2M:never
See Documentation/admin-guide/mm/transhuge.rst for more details.
Configuring the defaults at boot time is useful to allow early user space to take advantage of mTHP before its been configured through sysfs.
---
-v6:
* collect acked-by of David, thanks!
* some minor cleanup according to David's comments
.../admin-guide/kernel-parameters.txt | 9 ++ Documentation/admin-guide/mm/transhuge.rst | 38 +++++-- mm/huge_memory.c | 98 ++++++++++++++++++- 3 files changed, 137 insertions(+), 8 deletions(-)
Documentation/admin-guide/kernel-parameters.txt +9 -0
@@ -6629,6 +6629,15 @@ <deci-seconds>: poll all this frequency 0: no polling (default) + thp_anon= [KNL] + Format: <size>,<size>[KMG]:<state>;<size>-<size>[KMG]:<state> + state is one of "always", "madvise", "never" or "inherit". + Control the default behavior of the system with respect + to anonymous transparent hugepages. + Can be used multiple times for multiple anon THP sizes. + See Documentation/admin-guide/mm/transhuge.rst for more + details. + threadirqs [KNL,EARLY] Force threading of all interrupt handlers except those marked explicitly IRQF_NO_THREAD.
Documentation/admin-guide/mm/transhuge.rst +31 -7
@@ -284,13 +284,37 @@ that THP is shared. Exceeding the number would block the collapse:: A higher value may increase memory footprint for some workloads. -Boot parameter -============== - -You can change the sysfs boot time defaults of Transparent Hugepage -Support by passing the parameter ``transparent_hugepage=always`` or -``transparent_hugepage=madvise`` or ``transparent_hugepage=never`` -to the kernel command line. +Boot parameters +=============== + +You can change the sysfs boot time default for the top-level "enabled" +control by passing the parameter ``transparent_hugepage=always`` or +``transparent_hugepage=madvise`` or ``transparent_hugepage=never`` to the +kernel command line. + +Alternatively, each supported anonymous THP size can be controlled by +passing ``thp_anon=<size>,<size>[KMG]:<state>;<size>-<size>[KMG]:<state>``, +where ``<size>`` is the THP size (must be a power of 2 of PAGE_SIZE and +supported anonymous THP) and ``<state>`` is one of ``always``, ``madvise``, +``never`` or ``inherit``. + +For example, the following will set 16K, 32K, 64K THP to ``always``, +set 128K, 512K to ``inherit``, set 256K to ``madvise`` and 1M, 2M +to ``never``:: + + thp_anon=16K-64K:always;128K,512K:inherit;256K:madvise;1M-2M:never + +``thp_anon=`` may be specified multiple times to configure all THP sizes as +required. If ``thp_anon=`` is specified at least once, any anon THP sizes +not explicitly configured on the command line are implicitly set to +``never``. + +``transparent_hugepage`` setting only affects the global toggle. If +``thp_anon`` is not specified, PMD_ORDER THP will default to ``inherit``. +However, if a valid ``thp_anon`` setting is provided by the user, the +PMD_ORDER THP policy will be overridden. If the policy for PMD_ORDER +is not defined within a valid ``thp_anon``, its policy will default to +``never``. Hugepages in tmpfs/shmem ========================
mm/huge_memory.c +97 -1
116 lines not on this page · raw message
Signature · 1 line
2.39.3 (Apple Git-146)