Skip to contentSkip to conversation

add some node for amlogic c3

PATCH Applied Xianwei Zhao 3 participants 9 messages Aug 30, 2024

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

v4 cover add some node for amlogic c3

Add some node for board AW409 and support board C308l AW419.

---
Changes in v4:
- Adjust the format of commit message.
- Link to v3: https://lore.kernel.org/r/[email protected]

Changes in v3:
- Change clkc_periphs node to the first.
- Link to v2: https://lore.kernel.org/r/[email protected]

Changes in v2:
- Delete unused sdio node in board level dts.
- Add the description of modifying the binding in commit msg.
- Add the reason why some node property fileds place at board level in commit msg.
- Link to v1: https://lore.kernel.org/r/[email protected]

---
Xianwei Zhao (3):
dt-bindings: clock: fix C3 PLL input parameter
arm64: dts: amlogic: add some device nodes for C3
arm64: dts: amlogic: add C3 AW419 board

 .../bindings/clock/amlogic,c3-pll-clkc.yaml        |   7 +-
 arch/arm64/boot/dts/amlogic/Makefile               |   1 +
 .../boot/dts/amlogic/amlogic-c3-c302x-aw409.dts    | 233 ++++++++++
 .../boot/dts/amlogic/amlogic-c3-c308l-aw419.dts    | 262 +++++++++++
 arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi        | 488 ++++++++++++++++++++-
 5 files changed, 988 insertions(+), 3 deletions(-)

---
base-commit: 7a5d2ce79d1fc8535a6f10e51011ae9671bd86e8
change-id: 20240806-c3_add_node-420a37918f18

Best regards,

Signature · 1 line
Xianwei Zhao <[email protected]>
#1 lore raw

PATCH v4 1/3 dt-bindings: clock: fix C3 PLL input parameter

Add C3 PLL controller input clock parameters "fix".

The clock named "fix" was initially implemented in PLL clock controller driver. However, some registers required secure zone access, so we moved it to the secure zone (BL31) and accessed it through SCMI. Since the PLL clock driver needs to use this clock, the "fix" clock is used as an input source. We updated the driver but forgot to modify the binding accordingly, so we are adding it here.

It is an ABI break but on a new and immature platform. Noboby could really use that platform at this stage, so nothing is going to break on anyone really.

Fixes 0e6be855a96d ("dt-bindings: clock: add Amlogic C3 PLL clock controller")
---
 Documentation/devicetree/bindings/clock/amlogic,c3-pll-clkc.yaml | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)
Documentation/devicetree/bindings/clock/amlogic,c3-pll-clkc.yaml +5 -2
index 43de3c6fc1cf..700865cc9792 100644
@@ -24,11 +24,13 @@ properties:
     items:
       - description: input top pll
       - description: input mclk pll
+      - description: input fix pll
 
   clock-names:
     items:
       - const: top
       - const: mclk
+      - const: fix
 
   "#clock-cells":
     const: 1
@@ -52,8 +54,9 @@ examples:
             compatible = "amlogic,c3-pll-clkc";
             reg = <0x0 0x8000 0x0 0x1a4>;
             clocks = <&scmi_clk 2>,
-                     <&scmi_clk 5>;
-            clock-names = "top", "mclk";
+                     <&scmi_clk 5>,
+                     <&scmi_clk 12>;
+            clock-names = "top", "mclk", "fix";
             #clock-cells = <1>;
         };
     };
Signature · 1 line
2.37.1
maintainer
#2 lore raw

Re: [PATCH v4 1/3] dt-bindings: clock: fix C3 PLL input parameter

Hi Jerome,

Quoted 15 lines · On 30/08/2024 07:26, Xianwei Zhao via B4 Relay wrote:

From: Xianwei Zhao <[email protected]>

Add C3 PLL controller input clock parameters "fix".

The clock named "fix" was initially implemented in PLL clock controller driver. However, some registers required secure zone access, so we moved it to the secure zone (BL31) and accessed it through SCMI. Since the PLL clock driver needs to use this clock, the "fix" clock is used as an input source. We updated the driver but forgot to modify the binding accordingly, so we are adding it here.

It is an ABI break but on a new and immature platform. Noboby could really use that platform at this stage, so nothing is going to break on anyone really.

Quoted 5 lines
Fixes 0e6be855a96d ("dt-bindings: clock: add Amlogic C3 PLL clock controller")
---
  Documentation/devicetree/bindings/clock/amlogic,c3-pll-clkc.yaml | 7 +++++--

So you mind if I take this one via my arm64-dt tree ?

Neil

<snip>

maintainer
#3 lore raw

Re: [PATCH v4 1/3] dt-bindings: clock: fix C3 PLL input parameter

Quoted 22 lines · Neil Armstrong

Hi Jerome,

Quoted 12 lines · On 30/08/2024 07:26, Xianwei Zhao via B4 Relay wrote:

From: Xianwei Zhao <[email protected]>
Add C3 PLL controller input clock parameters "fix".
The clock named "fix" was initially implemented in PLL clock controller driver. However, some registers required secure zone access, so we moved it to the secure zone (BL31) and accessed it through SCMI. Since the PLL clock driver needs to use this clock, the "fix" clock is used as an input source. We updated the driver but forgot to modify the binding accordingly, so we are adding it here.
It is an ABI break but on a new and immature platform. Noboby could really
use that platform at this stage, so nothing is going to break on anyone really.

Quoted 6 lines
Fixes 0e6be855a96d ("dt-bindings: clock: add Amlogic C3 PLL clock

controller")

---
  Documentation/devicetree/bindings/clock/amlogic,c3-pll-clkc.yaml | 7 +++++--
Quoted 1 line

So you mind if I take this one via my arm64-dt tree ?

There is no conflicting change in my tree so it's fine, yes.

Quoted 4 lines

Neil

<snip>

Signature · 1 line
Jerome
maintainer
#4 lore raw

Re: [PATCH v4 1/3] dt-bindings: clock: fix C3 PLL input parameter

Quoted 24 lines · Jerome Brunet
Quoted 22 lines · Neil Armstrong

Hi Jerome,

Quoted 18 lines · On 30/08/2024 07:26, Xianwei Zhao via B4 Relay wrote:

From: Xianwei Zhao <[email protected]>
Add C3 PLL controller input clock parameters "fix".
The clock named "fix" was initially implemented in PLL clock controller driver. However, some registers required secure zone access, so we moved it to the secure zone (BL31) and accessed it through SCMI. Since the PLL clock driver needs to use this clock, the "fix" clock is used as an input source. We updated the driver but forgot to modify the binding accordingly, so we are adding it here.
It is an ABI break but on a new and immature platform. Noboby could really
use that platform at this stage, so nothing is going to break on anyone really.

Fixes 0e6be855a96d ("dt-bindings: clock: add Amlogic C3 PLL clock

controller")

---
   Documentation/devicetree/bindings/clock/amlogic,c3-pll-clkc.yaml | 7 +++++--
Quoted 3 lines
Quoted 1 line

So you mind if I take this one via my arm64-dt tree ?

There is no conflicting change in my tree so it's fine, yes.

Thanks
Neil

Quoted 6 lines
Quoted 5 lines

Neil

<snip>

#5 lore raw

PATCH v4 2/3 arm64: dts: amlogic: add some device nodes for C3

In reply to Xianwei Zhao

Add some device nodes for SoC C3, including periphs clock controller node, PLL clock controller node, SPICC node, regulator node, NAND controller node, sdcard node, Ethernet MAC and PHY node.

The sdacrd depends on regulator and pinctrl(select), so some property fields are placed at the board level. The nand chip is placed on the board, So some property fields about SPIFC and NAND controller node are placed at the board level. THe Ethernet MAC support outchip PHY, so place this property field(select PHY) at the board level.

---
 .../boot/dts/amlogic/amlogic-c3-c302x-aw409.dts    | 233 ++++++++++
 arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi        | 488 ++++++++++++++++++++-
 2 files changed, 720 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/amlogic/amlogic-c3-c302x-aw409.dts +233 -0
index edce8850b338..b8d2037afc00 100644
@@ -16,14 +16,247 @@ / {
 
 	aliases {
 		serial0 = &uart_b;
+		spi0 = &spifc;
 	};
 
 	memory@0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x10000000>;
 	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* 9 MiB reserved for ARM Trusted Firmware */
+		secmon_reserved: secmon@7f00000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x07f00000 0x0 0x900000>;
+			no-map;
+		};
+	};
+
+	main_12v: regulator-main-12v {
+		compatible = "regulator-fixed";
+		regulator-name = "12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vcc_5v: regulator-vcc-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&main_12v>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vddq: regulator-vddq {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDQ";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		vin-supply = <&main_12v>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&main_12v>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vddao_1v8: regulator-vddao-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	ddr4_2v5: regulator-ddr4-2v5 {
+		compatible = "regulator-fixed";
+		regulator-name = "DDR4_2V5";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vcc_3v3: regulator-vcc-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vcc_1v8: regulator-vcc-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vdd_1v8: regulator-vdd-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD1V8_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vddio_b: regulator-vddio-3v3-b {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_B";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	sdcard: regulator-sdcard {
+		compatible = "regulator-fixed";
+		regulator-name = "SDCARD_POWER";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		gpio = <&gpio GPIOA_4 GPIO_ACTIVE_LOW>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
 };
 
 &uart_b {
 	status = "okay";
 };
+
+&nand {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+
+	nand@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		nand-on-flash-bbt;
+
+		partition@0 {
+			label = "boot";
+			reg = <0x0 0x00200000>;
+		};
+		partition@200000 {
+			label = "env";
+			reg = <0x00200000 0x00400000>;
+		};
+		partition@600000 {
+			label = "system";
+			reg = <0x00600000 0x00a00000>;
+		};
+		partition@1000000 {
+			label = "rootfs";
+			reg = <0x01000000 0x03000000>;
+		};
+		partition@4000000 {
+			label = "media";
+			reg = <0x04000000 0x8000000>;
+		};
+	};
+};
+
+&ethmac {
+	status = "okay";
+	phy-handle = <&internal_ephy>;
+	phy-mode = "rmii";
+};
+
+&spifc {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	pinctrl-0 = <&spifc_pins>;
+	pinctrl-names = "default";
+
+	nand@0 {
+		compatible = "spi-nand";
+		reg = <0>;
+		spi-max-frequency = <83000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		status = "disabled";
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "boot";
+				reg = <0 0x200000>;
+			};
+
+			partition@200000 {
+				label = "env";
+				reg = <0x200000 0x400000>;
+			};
+
+			partition@600000 {
+				label = "system";
+				reg = <0x600000 0xa00000>;
+			};
+
+			partition@1000000 {
+				label = "rootfs";
+				reg = <0x1000000 0x3000000>;
+			};
+
+			partition@4000000 {
+				label = "data";
+				reg = <0x4000000 0x8000000>;
+			};
+		};
+	};
+};
+
+&sd {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_pins>;
+	pinctrl-names = "default","clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&sdcard>;
+	vqmmc-supply = <&sdcard>;
+};
arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi +487 -1

530 lines not on this page · raw message

Signature · 1 line
2.37.1
maintainer Reviewed-by on v4 2/3
#6 lore raw

Re: [PATCH v4 2/3] arm64: dts: amlogic: add some device nodes for C3

Quoted 802 lines · On 30/08/2024 07:26, Xianwei Zhao via B4 Relay wrote:

From: Xianwei Zhao <[email protected]>

Add some device nodes for SoC C3, including periphs clock controller node, PLL clock controller node, SPICC node, regulator node, NAND controller node, sdcard node, Ethernet MAC and PHY node.

The sdacrd depends on regulator and pinctrl(select), so some property fields are placed at the board level. The nand chip is placed on the board, So some property fields about SPIFC and NAND controller node are placed at the board level. THe Ethernet MAC support outchip PHY, so place this property field(select PHY) at the board level.

---
  .../boot/dts/amlogic/amlogic-c3-c302x-aw409.dts    | 233 ++++++++++
  arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi        | 488 ++++++++++++++++++++-
  2 files changed, 720 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/amlogic/amlogic-c3-c302x-aw409.dts +233 -0
index edce8850b338..b8d2037afc00 100644
@@ -16,14 +16,247 @@ / {
 
  	aliases {
  		serial0 = &uart_b;
+		spi0 = &spifc;
  	};
 
  	memory@0 {
  		device_type = "memory";
  		reg = <0x0 0x0 0x0 0x10000000>;
  	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* 9 MiB reserved for ARM Trusted Firmware */
+		secmon_reserved: secmon@7f00000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x07f00000 0x0 0x900000>;
+			no-map;
+		};
+	};
+
+	main_12v: regulator-main-12v {
+		compatible = "regulator-fixed";
+		regulator-name = "12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vcc_5v: regulator-vcc-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&main_12v>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vddq: regulator-vddq {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDQ";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		vin-supply = <&main_12v>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&main_12v>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vddao_1v8: regulator-vddao-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	ddr4_2v5: regulator-ddr4-2v5 {
+		compatible = "regulator-fixed";
+		regulator-name = "DDR4_2V5";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vcc_3v3: regulator-vcc-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vcc_1v8: regulator-vcc-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vdd_1v8: regulator-vdd-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD1V8_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vddio_b: regulator-vddio-3v3-b {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_B";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	sdcard: regulator-sdcard {
+		compatible = "regulator-fixed";
+		regulator-name = "SDCARD_POWER";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		gpio = <&gpio GPIOA_4 GPIO_ACTIVE_LOW>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
  };
 
  &uart_b {
  	status = "okay";
  };
+
+&nand {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+
+	nand@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		nand-on-flash-bbt;
+
+		partition@0 {
+			label = "boot";
+			reg = <0x0 0x00200000>;
+		};
+		partition@200000 {
+			label = "env";
+			reg = <0x00200000 0x00400000>;
+		};
+		partition@600000 {
+			label = "system";
+			reg = <0x00600000 0x00a00000>;
+		};
+		partition@1000000 {
+			label = "rootfs";
+			reg = <0x01000000 0x03000000>;
+		};
+		partition@4000000 {
+			label = "media";
+			reg = <0x04000000 0x8000000>;
+		};
+	};
+};
+
+&ethmac {
+	status = "okay";
+	phy-handle = <&internal_ephy>;
+	phy-mode = "rmii";
+};
+
+&spifc {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	pinctrl-0 = <&spifc_pins>;
+	pinctrl-names = "default";
+
+	nand@0 {
+		compatible = "spi-nand";
+		reg = <0>;
+		spi-max-frequency = <83000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		status = "disabled";
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "boot";
+				reg = <0 0x200000>;
+			};
+
+			partition@200000 {
+				label = "env";
+				reg = <0x200000 0x400000>;
+			};
+
+			partition@600000 {
+				label = "system";
+				reg = <0x600000 0xa00000>;
+			};
+
+			partition@1000000 {
+				label = "rootfs";
+				reg = <0x1000000 0x3000000>;
+			};
+
+			partition@4000000 {
+				label = "data";
+				reg = <0x4000000 0x8000000>;
+			};
+		};
+	};
+};
+
+&sd {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_pins>;
+	pinctrl-names = "default","clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&sdcard>;
+	vqmmc-supply = <&sdcard>;
+};
arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi +480 -1
index c913dd409e64..c0ce776ec463 100644
@@ -7,6 +7,11 @@
  #include <dt-bindings/interrupt-controller/arm-gic.h>
  #include <dt-bindings/gpio/gpio.h>
  #include <dt-bindings/reset/amlogic,c3-reset.h>
+#include <dt-bindings/clock/amlogic,c3-pll-clkc.h>
+#include <dt-bindings/clock/amlogic,c3-scmi-clkc.h>
+#include <dt-bindings/clock/amlogic,c3-peripherals-clkc.h>
+#include <dt-bindings/power/amlogic,c3-pwrc.h>
+#include <dt-bindings/gpio/amlogic-c3-gpio.h>
 
  / {
  	cpus {
@@ -57,6 +62,34 @@ pwrc: power-controller {
  		};
  	};
 
+	sram {
+		compatible = "mmio-sram";
+		reg = <0x0 0x07f50e00 0x0 0x100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x0 0x07f50e00 0x100>;
+
+		scmi_shmem: sram@0 {
+			compatible = "arm,scmi-shmem";
+			reg = <0x0 0x100>;
+		};
+	};
+
+	firmware {
+		scmi: scmi {
+			compatible = "arm,scmi-smc";
+			arm,smc-id = <0x820000C1>;
+			shmem = <&scmi_shmem>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			scmi_clk: protocol@14 {
+				reg = <0x14>;
+				#clock-cells = <1>;
+			};
+		};
+	};
+
  	soc {
  		compatible = "simple-bus";
  		#address-cells = <2>;
@@ -82,6 +115,44 @@ apb4: bus@fe000000 {
  			#size-cells = <2>;
  			ranges = <0x0 0x0 0x0 0xfe000000 0x0 0x480000>;
 
+			clkc_periphs: clock-controller@0 {
+				compatible = "amlogic,c3-peripherals-clkc";
+				reg = <0x0 0x0 0x0 0x49c>;
+				#clock-cells = <1>;
+				clocks = <&xtal>,
+					 <&scmi_clk CLKID_OSC>,
+					 <&scmi_clk CLKID_FIXED_PLL_OSC>,
+					 <&clkc_pll CLKID_FCLK_DIV2>,
+					 <&clkc_pll CLKID_FCLK_DIV2P5>,
+					 <&clkc_pll CLKID_FCLK_DIV3>,
+					 <&clkc_pll CLKID_FCLK_DIV4>,
+					 <&clkc_pll CLKID_FCLK_DIV5>,
+					 <&clkc_pll CLKID_FCLK_DIV7>,
+					 <&clkc_pll CLKID_GP0_PLL>,
+					 <&scmi_clk CLKID_GP1_PLL_OSC>,
+					 <&clkc_pll CLKID_HIFI_PLL>,
+					 <&scmi_clk CLKID_SYS_CLK>,
+					 <&scmi_clk CLKID_AXI_CLK>,
+					 <&scmi_clk CLKID_SYS_PLL_DIV16>,
+					 <&scmi_clk CLKID_CPU_CLK_DIV16>;
+				clock-names = "xtal_24m",
+					      "oscin",
+					      "fix",
+					      "fdiv2",
+					      "fdiv2p5",
+					      "fdiv3",
+					      "fdiv4",
+					      "fdiv5",
+					      "fdiv7",
+					      "gp0",
+					      "gp1",
+					      "hifi",
+					      "sysclk",
+					      "axiclk",
+					      "sysplldiv16",
+					      "cpudiv16";
+			};
+
  			reset: reset-controller@2000 {
  				compatible = "amlogic,c3-reset";
  				reg = <0x0 0x2000 0x0 0x98>;
@@ -108,6 +179,237 @@ gpio: bank@4000 {
  					#gpio-cells = <2>;
  					gpio-ranges = <&periphs_pinctrl 0 0 55>;
  				};
+
+				i2c0_pins1: i2c0-pins1 {
+					mux {
+						groups = "i2c0_sda_e",
+							 "i2c0_scl_e";
+						function = "i2c0";
+						bias-disable;
+						drive-strength-microamp = <3000>;
+					};
+				};
+
+				i2c0_pins2: i2c0-pins2 {
+					mux {
+						groups = "i2c0_sda_d",
+							 "i2c0_scl_d";
+						function = "i2c0";
+						bias-disable;
+						drive-strength-microamp = <3000>;
+					};
+				};
+
+				i2c1_pins1: i2c1-pins1 {
+					mux {
+						groups = "i2c1_sda_x",
+							 "i2c1_scl_x";
+						function = "i2c1";
+						bias-disable;
+						drive-strength-microamp = <3000>;
+					};
+				};
+
+				i2c1_pins2: i2c1-pins2 {
+					mux {
+						groups = "i2c1_sda_d",
+							 "i2c1_scl_d";
+						function = "i2c1";
+						bias-disable;
+						drive-strength-microamp = <3000>;
+					};
+				};
+
+				i2c1_pins3: i2c1-pins3 {
+					mux {
+						groups = "i2c1_sda_a",
+							 "i2c1_scl_a";
+						function = "i2c1";
+						bias-disable;
+						drive-strength-microamp = <3000>;
+					};
+				};
+
+				i2c1_pins4: i2c1-pins4 {
+					mux {
+						groups = "i2c1_sda_b",
+							 "i2c1_scl_b";
+						function = "i2c1";
+						bias-disable;
+						drive-strength-microamp = <3000>;
+					};
+				};
+
+				i2c2_pins1: i2c2-pins1 {
+					mux {
+						groups = "i2c2_sda",
+							 "i2c2_scl";
+						function = "i2c2";
+						bias-disable;
+						drive-strength-microamp = <3000>;
+					};
+				};
+
+				i2c3_pins1: i2c3-pins1 {
+					mux {
+						groups = "i2c3_sda_c",
+							 "i2c3_scl_c";
+						function = "i2c3";
+						bias-disable;
+						drive-strength-microamp = <3000>;
+					};
+				};
+
+				i2c3_pins2: i2c3-pins2 {
+					mux {
+						groups = "i2c3_sda_x",
+							 "i2c3_scl_x";
+						function = "i2c3";
+						bias-disable;
+						drive-strength-microamp = <3000>;
+					};
+				};
+
+				i2c3_pins3: i2c3-pins3 {
+					mux {
+						groups = "i2c3_sda_d",
+							 "i2c3_scl_d";
+						function = "i2c3";
+						bias-disable;
+						drive-strength-microamp = <3000>;
+					};
+				};
+
+				nand_pins: nand-pins {
+					mux {
+						groups = "emmc_nand_d0",
+							 "emmc_nand_d1",
+							 "emmc_nand_d2",
+							 "emmc_nand_d3",
+							 "emmc_nand_d4",
+							 "emmc_nand_d5",
+							 "emmc_nand_d6",
+							 "emmc_nand_d7",
+							 "nand_ce0",
+							 "nand_ale",
+							 "nand_cle",
+							 "nand_wen_clk",
+							 "nand_ren_wr";
+						function = "nand";
+						input-enable;
+					};
+				};
+
+				sdcard_pins: sdcard-pins {
+					mux {
+						groups = "sdcard_d0",
+							 "sdcard_d1",
+							 "sdcard_d2",
+							 "sdcard_d3",
+							 "sdcard_clk",
+							 "sdcard_cmd";
+						function = "sdcard";
+						bias-pull-up;
+						drive-strength-microamp = <4000>;
+					};
+				};
+
+				sdcard_clk_gate_pins: sdcard-clk-cmd-pins {
+					mux {
+						groups = "GPIOC_4";
+						function = "gpio_periphs";
+						bias-pull-down;
+						drive-strength-microamp = <4000>;
+					};
+				};
+
+				sdio_m_clk_gate_pins: sdio-m-clk-cmd-pins {
+					mux {
+						groups = "sdio_clk";
+						function = "sdio";
+						bias-pull-down;
+						drive-strength-microamp = <4000>;
+					};
+				};
+
+				sdio_m_pins: sdio-m-all-pins {
+					mux {
+						groups = "sdio_d0",
+							 "sdio_d1",
+							 "sdio_d2",
+							 "sdio_d3",
+							 "sdio_clk",
+							 "sdio_cmd";
+						function = "sdio";
+						input-enable;
+						bias-pull-up;
+						drive-strength-microamp = <4000>;
+					};
+				};
+
+				spicc0_pins1: spicc0-pins1 {
+					mux {
+						groups = "spi_a_mosi_b",
+							 "spi_a_miso_b",
+							 "spi_a_clk_b";
+						function = "spi_a";
+						drive-strength-microamp = <3000>;
+					};
+				};
+
+				spicc0_pins2: spicc0-pins2 {
+					mux {
+						groups = "spi_a_mosi_c",
+							 "spi_a_miso_c",
+							 "spi_a_clk_c";
+						function = "spi_a";
+						drive-strength-microamp = <3000>;
+					};
+				};
+
+				spicc0_pins3: spicc0-pins3 {
+					mux {
+						groups = "spi_a_mosi_x",
+							 "spi_a_miso_x",
+							 "spi_a_clk_x";
+						function = "spi_a";
+						drive-strength-microamp = <3000>;
+					};
+				};
+
+				spicc1_pins1: spicc1-pins1 {
+					mux {
+						groups = "spi_b_mosi_d",
+							 "spi_b_miso_d",
+							 "spi_b_clk_d";
+						function = "spi_b";
+						drive-strength-microamp = <3000>;
+					};
+				};
+
+				spicc1_pins2: spicc1-pins2 {
+					mux {
+						groups = "spi_b_mosi_x",
+							 "spi_b_miso_x",
+							 "spi_b_clk_x";
+						function = "spi_b";
+						drive-strength-microamp = <3000>;
+					};
+				};
+
+				spifc_pins: spifc-pins {
+					mux {
+						groups = "spif_mo",
+							 "spif_mi",
+							 "spif_clk",
+							 "spif_cs",
+							 "spif_hold",
+							 "spif_wp",
+							 "spif_clk_loop";
+						function = "spif";
+						drive-strength-microamp = <4000>;
+					};
+				};
  			};
 
  			gpio_intc: interrupt-controller@4080 {
@@ -119,13 +421,131 @@ gpio_intc: interrupt-controller@4080 {
  					<10 11 12 13 14 15 16 17 18 19 20 21>;
  			};
 
+			clkc_pll: clock-controller@8000 {
+				compatible = "amlogic,c3-pll-clkc";
+				reg = <0x0 0x8000 0x0 0x1a4>;
+				#clock-cells = <1>;
+				clocks = <&scmi_clk CLKID_TOP_PLL_OSC>,
+					 <&scmi_clk CLKID_MCLK_PLL_OSC>,
+					 <&scmi_clk CLKID_FIXED_PLL_OSC>;
+				clock-names = "top",
+					      "mclk",
+					      "fix";
+			};
+
+			eth_phy: mdio-multiplexer@28000 {
+				compatible = "amlogic,g12a-mdio-mux";
+				reg = <0x0 0x28000 0x0 0xa4>;
+
+				clocks = <&clkc_periphs CLKID_SYS_ETH_PHY>,
+					 <&xtal>,
+					 <&clkc_pll CLKID_FCLK_50M>;
+				clock-names = "pclk", "clkin0", "clkin1";
+				mdio-parent-bus = <&mdio0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ext_mdio: mdio@0 {
+					reg = <0>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+
+				int_mdio: mdio@1 {
+					reg = <1>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					internal_ephy: ethernet_phy@8 {
+						compatible = "ethernet-phy-id0180.3301",
+							     "ethernet-phy-ieee802.3-c22";
+						interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+						reg = <8>;
+						max-speed = <100>;
+					};
+				};
+			};
+
+			spicc0: spi@50000 {
+				compatible = "amlogic,meson-g12a-spicc";
+				reg = <0x0 0x50000 0x0 0x44>;
+				interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clkc_periphs CLKID_SYS_SPICC_0>,
+					 <&clkc_periphs CLKID_SPICC_A>;
+				clock-names = "core", "pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spicc1: spi@52000 {
+				compatible = "amlogic,meson-g12a-spicc";
+				reg = <0x0 0x52000 0x0 0x44>;
+				interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clkc_periphs CLKID_SYS_SPICC_1>,
+					 <&clkc_periphs CLKID_SPICC_B>;
+				clock-names = "core", "pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spifc: spi@56000 {
+				compatible = "amlogic,a1-spifc";
+				reg = <0x0 0x56000 0x0 0x290>;
+				interrupts = <GIC_SPI 182 IRQ_TYPE_EDGE_RISING>;
+				clocks = <&clkc_periphs CLKID_SPIFC>;
+				clock-names = "core";
+				status = "disabled";
+			};
+
+			i2c0: i2c@66000 {
+				compatible = "amlogic,meson-axg-i2c";
+				reg = <0x0 0x66000 0x0 0x24>;
+				interrupts = <GIC_SPI 160 IRQ_TYPE_EDGE_RISING>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clkc_periphs CLKID_SYS_I2C_M_A>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@68000 {
+				compatible = "amlogic,meson-axg-i2c";
+				reg = <0x0 0x68000 0x0 0x24>;
+				interrupts = <GIC_SPI 161 IRQ_TYPE_EDGE_RISING>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clkc_periphs CLKID_SYS_I2C_M_B>;
+				status = "disabled";
+			};
+
+			i2c2: i2c@6a000 {
+				compatible = "amlogic,meson-axg-i2c";
+				reg = <0x0 0x6a000 0x0 0x24>;
+				interrupts = <GIC_SPI 162 IRQ_TYPE_EDGE_RISING>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clkc_periphs CLKID_SYS_I2C_M_C>;
+				status = "disabled";
+			};
+
+			i2c3: i2c@6c000 {
+				compatible = "amlogic,meson-axg-i2c";
+				reg = <0x0 0x6c000 0x0 0x24>;
+				interrupts = <GIC_SPI 163 IRQ_TYPE_EDGE_RISING>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clkc_periphs CLKID_SYS_I2C_M_D>;
+				status = "disabled";
+			};
+
  			uart_b: serial@7a000 {
  				compatible = "amlogic,meson-s4-uart",
  					   "amlogic,meson-ao-uart";
  				reg = <0x0 0x7a000 0x0 0x18>;
  				interrupts = <GIC_SPI 169 IRQ_TYPE_EDGE_RISING>;
  				status = "disabled";
-				clocks = <&xtal>, <&xtal>, <&xtal>;
+				clocks = <&xtal>, <&clkc_periphs CLKID_SYS_UART_B>, <&xtal>;
  				clock-names = "xtal", "pclk", "baud";
  			};
 
@@ -136,6 +556,72 @@ sec_ao: ao-secure@10220 {
  				reg = <0x0 0x10220 0x0 0x140>;
  				amlogic,has-chip-id;
  			};
+
+			sdio: mmc@88000 {
+				compatible = "amlogic,meson-axg-mmc";
+				reg = <0x0 0x88000 0x0 0x800>;
+				interrupts = <GIC_SPI 176 IRQ_TYPE_EDGE_RISING>;
+				power-domains = <&pwrc PWRC_C3_SDIOA_ID>;
+				clocks = <&clkc_periphs CLKID_SYS_SD_EMMC_A>,
+					  <&clkc_periphs CLKID_SD_EMMC_A>,
+					  <&clkc_pll CLKID_FCLK_DIV2>;
+				clock-names = "core","clkin0", "clkin1";
+				no-mmc;
+				no-sd;
+				resets = <&reset RESET_SD_EMMC_A>;
+				status = "disabled";
+			};
+
+			sd: mmc@8a000 {
+				compatible = "amlogic,meson-axg-mmc";
+				reg = <0x0 0x8a000 0x0 0x800>;
+				interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>;
+				power-domains = <&pwrc PWRC_C3_SDCARD_ID>;
+				clocks = <&clkc_periphs CLKID_SYS_SD_EMMC_B>,
+					<&clkc_periphs CLKID_SD_EMMC_B>,
+					<&clkc_pll CLKID_FCLK_DIV2>;
+				clock-names = "core", "clkin0", "clkin1";
+				no-mmc;
+				no-sdio;
+				resets = <&reset RESET_SD_EMMC_B>;
+				status = "disabled";
+			};
+
+			nand: nand-controller@8d000 {
+				compatible = "amlogic,meson-axg-nfc";
+				reg = <0x0 0x8d000 0x0 0x200>,
+					<0x0 0x8C000 0x0 0x4>;
+				reg-names = "nfc", "emmc";
+				interrupts = <GIC_SPI 87 IRQ_TYPE_EDGE_RISING>;
+				clocks = <&clkc_periphs CLKID_SYS_SD_EMMC_C>,
+					<&clkc_pll CLKID_FCLK_DIV2>;
+				clock-names = "core", "device";
+				status = "disabled";
+			};
+		};
+
+		ethmac: ethernet@fdc00000 {
+			compatible = "amlogic,meson-g12a-dwmac",
+				     "snps,dwmac-3.70a",
+				     "snps,dwmac";
+			reg = <0x0 0xfdc00000 0x0 0x10000>,
+			      <0x0 0xfe024000 0x0 0x8>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			power-domains = <&pwrc PWRC_C3_ETH_ID>;
+			clocks = <&clkc_periphs CLKID_SYS_ETH_MAC>,
+				 <&clkc_pll CLKID_FCLK_DIV2>,
+				 <&clkc_pll CLKID_FCLK_50M>;
+			clock-names = "stmmaceth", "clkin0", "clkin1";
+			rx-fifo-depth = <4096>;
+			tx-fifo-depth = <2048>;

arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi sec_ao: ao-secure@10220 { · line 627

Quoted 10 lines
arch/arm64/boot/dts/amlogic/amlogic-c3.dtsi +7 -0
+			status = "disabled";
+
+			mdio0: mdio {
+				compatible = "snps,dwmac-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
  		};
  	};
  };
#7 lore raw

PATCH v4 3/3 arm64: dts: amlogic: add C3 AW419 board

In reply to Xianwei Zhao

Add Amlogic C3 C308L AW419 board. The corresponding binding has been applied, therefore, this series does not need to add a binding corresponding to the AW419 board.

---
 arch/arm64/boot/dts/amlogic/Makefile               |   1 +
 .../boot/dts/amlogic/amlogic-c3-c308l-aw419.dts    | 262 +++++++++++++++++++++
 2 files changed, 263 insertions(+)
arch/arm64/boot/dts/amlogic/Makefile +1 -0
index 9708abdadd7c..8db42f26c1e6 100644
@@ -2,6 +2,7 @@
 dtb-$(CONFIG_ARCH_MESON) += amlogic-a4-a113l2-ba400.dtb
 dtb-$(CONFIG_ARCH_MESON) += amlogic-a5-a113x2-av400.dtb
 dtb-$(CONFIG_ARCH_MESON) += amlogic-c3-c302x-aw409.dtb
+dtb-$(CONFIG_ARCH_MESON) += amlogic-c3-c308l-aw419.dtb
 dtb-$(CONFIG_ARCH_MESON) += amlogic-t7-a311d2-an400.dtb
 dtb-$(CONFIG_ARCH_MESON) += amlogic-t7-a311d2-khadas-vim4.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-a1-ad401.dtb
arch/arm64/boot/dts/amlogic/amlogic-c3-c308l-aw419.dts new file +262 -0

262 lines not on this page · raw message

Signature · 1 line
2.37.1
maintainer Applied
#8 lore raw
In reply to Xianwei Zhao

Hi,

Quoted 3 lines · Xianwei Zhao

Add some node for board AW409 and support board C308l AW419.

Thanks, Applied to https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git (v6.12/arm64-dt)

[1/3] dt-bindings: clock: fix C3 PLL input parameter

      https://git.kernel.org/amlogic/c/4ccba8cb2c5ca573d9bbf366e7d9d5e9761518c0
[2/3] arm64: dts: amlogic: add some device nodes for C3
      https://git.kernel.org/amlogic/c/520b792e83171efc8ec0b004412b44dabc044de0
[3/3] arm64: dts: amlogic: add C3 AW419 board
      https://git.kernel.org/amlogic/c/d4bd8f3023b68f72431e05ec6cbc793519b449cf

These changes has been applied on the intermediate git tree [1].

The v6.12/arm64-dt branch will then be sent via a formal Pull Request to the Linux SoC maintainers for inclusion in their intermediate git branches in order to be sent to Linus during the next merge window, or sooner if it's a set of fixes.

In the cases of fixes, those will be merged in the current release candidate kernel and as soon they appear on the Linux master branch they will be backported to the previous Stable and Long-Stable kernels [2].

The intermediate git branches are merged daily in the linux-next tree [3], people are encouraged testing these pre-release kernels and report issues on the relevant mailing-lists.

If problems are discovered on those changes, please submit a signed-off-by revert patch followed by a corrective changeset.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux.git
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git
[3] https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git

Signature · 1 line
Neil