Skip to contentSkip to conversation

riscv: sbi: Add support to test HSM extension

PATCH Superseded James Raphael Tiovalen 2 participants 7 messages Sep 15, 2024 – Sep 16, 2024

Subsystems (3)

v4 of 7 Superseded Latest is v7 →

lore
Share & tools
lore
#0 lore raw

v4 cover riscv: sbi: Add support to test HSM extension

This patch series adds support for testing all 4 functions of the HSM extension as defined in the RISC-V SBI specification. The first 2 patches adds some helper routines to prepare for the HSM test, while the third patch adds the actual test for the HSM extension.

v4:
- Addressed all of Andrew's comments.
- Included the 2 patches from Andrew's branch that refactored some functions.
- Added timers to all of the waiting activities in the HSM tests.

v3:
- Addressed all of Andrew's comments.
- Split the report_prefix_pop patch into its own series.
- Added a new environment variable to specify the maximum number of CPUs supported by the SBI implementation.

v2:
- Addressed all of Andrew's comments.
- Added a new patch to add helper routines to clear multiple prefixes.
- Reworked the approach to test the HSM extension by using cpumask and on-cpus.

Andrew Jones (1):
riscv: Rewrite hartid_to_cpu in assembly

James Raphael Tiovalen (2):
riscv: sbi: Provide entry point for HSM tests
riscv: sbi: Add tests for HSM extension

 riscv/Makefile          |   3 +-
 lib/riscv/asm-offsets.c |   5 +
 lib/riscv/setup.c       |  10 -
 riscv/sbi-tests.h       |  10 +
 riscv/sbi.h             |  10 +
 riscv/cstart.S          |  23 ++
 riscv/sbi-asm.S         |  71 +++++
 riscv/sbi.c             | 566 ++++++++++++++++++++++++++++++++++++++++
 8 files changed, 687 insertions(+), 11 deletions(-)
 create mode 100644 riscv/sbi-tests.h
 create mode 100644 riscv/sbi.h
 create mode 100644 riscv/sbi-asm.S

--
2.43.0

#1 lore raw

PATCH v4 1/3 riscv: Rewrite hartid_to_cpu in assembly

From: Andrew Jones <[email protected]>

Some SBI HSM tests run without a stack being setup so they can't run C code. Those tests still need to know the corresponding cpuid for the hartid on which they are running. Give those tests hartid_to_cpu() by reimplementing it in assembly.

---
 lib/riscv/asm-offsets.c |  5 +++++
 lib/riscv/setup.c       | 10 ----------
 riscv/cstart.S          | 23 +++++++++++++++++++++++
 3 files changed, 28 insertions(+), 10 deletions(-)
lib/riscv/asm-offsets.c +5 -0
index a2a32438..6c511c14 100644
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0-only
 #include <kbuild.h>
 #include <elf.h>
+#include <asm/processor.h>
 #include <asm/ptrace.h>
 #include <asm/smp.h>
 
@@ -58,5 +59,9 @@ int main(void)
 	OFFSET(SECONDARY_FUNC, secondary_data, func);
 	DEFINE(SECONDARY_DATA_SIZE, sizeof(struct secondary_data));
 
+	OFFSET(THREAD_INFO_CPU, thread_info, cpu);
+	OFFSET(THREAD_INFO_HARTID, thread_info, hartid);
+	DEFINE(THREAD_INFO_SIZE, sizeof(struct thread_info));
+
 	return 0;
 }
lib/riscv/setup.c +0 -10
index 495db041..f347ad63 100644
@@ -43,16 +43,6 @@ uint64_t timebase_frequency;
 
 static struct mem_region riscv_mem_regions[NR_MEM_REGIONS + 1];
 
-int hartid_to_cpu(unsigned long hartid)
-{
-	int cpu;
-
-	for_each_present_cpu(cpu)
-		if (cpus[cpu].hartid == hartid)
-			return cpu;
-	return -1;
-}
-
 static void cpu_set_fdt(int fdtnode __unused, u64 regval, void *info __unused)
 {
 	int cpu = nr_cpus++;
riscv/cstart.S +23 -0
index 8f269997..6784d5e1 100644
@@ -109,6 +109,29 @@ halt:
 1:	wfi
 	j	1b
 
+/*
+ * hartid_to_cpu
+ *   a0 is a hartid on entry
+ * returns the corresponding cpuid in a0
+ */
+.balign 4
+.global hartid_to_cpu
+hartid_to_cpu:
+	la	t0, cpus
+	la	t1, nr_cpus
+	lw	t1, 0(t1)
+	li	t2, 0
+1:	bne	t2, t1, 2f
+	li	a0, -1
+	ret
+2:	REG_L	t3, THREAD_INFO_HARTID(t0)
+	bne	a0, t3, 3f
+	lw	a0, THREAD_INFO_CPU(t0)
+	ret
+3:	addi	t0, t0, THREAD_INFO_SIZE
+	addi	t2, t2, 1
+	j	1b
+
 .balign 4
 .global secondary_entry
 secondary_entry:
Signature · 1 line
2.43.0
#2 lore raw

Re: [kvm-unit-tests PATCH v4 1/3] riscv: Rewrite hartid_to_cpu in assembly

Quoted 8 lines · James Raphael Tiovalen

From: Andrew Jones <[email protected]>

Some SBI HSM tests run without a stack being setup so they can't run C code. Those tests still need to know the corresponding cpuid for the hartid on which they are running. Give those tests hartid_to_cpu() by reimplementing it in assembly.

This should also include your sign-off since you're posting it and it's for your series. Passing unmodified patches on that you're comfortable passing on corresponds to (c) of [1]

[1] https://www.kernel.org/doc/html/v4.17/process/submitting-patches.html#developer-s-certificate-of-origin-1-1

Quoted 54 lines
---
 lib/riscv/asm-offsets.c |  5 +++++
 lib/riscv/setup.c       | 10 ----------
 riscv/cstart.S          | 23 +++++++++++++++++++++++
 3 files changed, 28 insertions(+), 10 deletions(-)
lib/riscv/asm-offsets.c +5 -0
index a2a32438..6c511c14 100644
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0-only
 #include <kbuild.h>
 #include <elf.h>
+#include <asm/processor.h>
 #include <asm/ptrace.h>
 #include <asm/smp.h>
 
@@ -58,5 +59,9 @@ int main(void)
 	OFFSET(SECONDARY_FUNC, secondary_data, func);
 	DEFINE(SECONDARY_DATA_SIZE, sizeof(struct secondary_data));
 
+	OFFSET(THREAD_INFO_CPU, thread_info, cpu);
+	OFFSET(THREAD_INFO_HARTID, thread_info, hartid);
+	DEFINE(THREAD_INFO_SIZE, sizeof(struct thread_info));
+
 	return 0;
 }
lib/riscv/setup.c +0 -10
index 495db041..f347ad63 100644
@@ -43,16 +43,6 @@ uint64_t timebase_frequency;
 
 static struct mem_region riscv_mem_regions[NR_MEM_REGIONS + 1];
 
-int hartid_to_cpu(unsigned long hartid)
-{
-	int cpu;
-
-	for_each_present_cpu(cpu)
-		if (cpus[cpu].hartid == hartid)
-			return cpu;
-	return -1;
-}
-
 static void cpu_set_fdt(int fdtnode __unused, u64 regval, void *info __unused)
 {
 	int cpu = nr_cpus++;
riscv/cstart.S +0 -0
index 8f269997..6784d5e1 100644

riscv/cstart.S halt: · line 115

Quoted 7 lines
riscv/cstart.S +4 -0
@@ -109,6 +109,29 @@ halt:
 1:	wfi
 	j	1b
 
+/*
+ * hartid_to_cpu
+ *   a0 is a hartid on entry
+ * returns the corresponding cpuid in a0

I should have capitalized the 'r' in 'returns' and also written "or -1 if no thread-info struct with 'hartid' is found."

Quoted 25 lines
riscv/cstart.S +19 -0
+ */
+.balign 4
+.global hartid_to_cpu
+hartid_to_cpu:
+	la	t0, cpus
+	la	t1, nr_cpus
+	lw	t1, 0(t1)
+	li	t2, 0
+1:	bne	t2, t1, 2f
+	li	a0, -1
+	ret
+2:	REG_L	t3, THREAD_INFO_HARTID(t0)
+	bne	a0, t3, 3f
+	lw	a0, THREAD_INFO_CPU(t0)
+	ret
+3:	addi	t0, t0, THREAD_INFO_SIZE
+	addi	t2, t2, 1
+	j	1b
+
 .balign 4
 .global secondary_entry
 secondary_entry:
Signature · 1 line
2.43.0

I'll fixup the comment and add your sign-off when applying.

Thanks,
drew

#3 lore raw

PATCH v4 2/3 riscv: sbi: Provide entry point for HSM tests

In reply to James Raphael Tiovalen

The HSM tests will need to test HSM start and resumption from HSM suspend. Provide an entry point written in assembly that doesn't use a stack for this. Results of the test are written to global per-hart arrays to be checked by the main SBI HSM test function. The started/resumed hart does its checks and then just loops until it gets a signal from the main SBI HSM test function to invoke HSM stop.

---
 riscv/Makefile    |  3 +-
 riscv/sbi-tests.h | 10 +++++++
 riscv/sbi-asm.S   | 71 +++++++++++++++++++++++++++++++++++++++++++++++
 riscv/sbi.c       |  5 ++++
 4 files changed, 88 insertions(+), 1 deletion(-)
 create mode 100644 riscv/sbi-tests.h
 create mode 100644 riscv/sbi-asm.S
riscv/Makefile +2 -1
index 2ee7c5bb..4676d262 100644
@@ -43,6 +43,7 @@ cflatobjs += lib/riscv/timer.o
 ifeq ($(ARCH),riscv32)
 cflatobjs += lib/ldiv32.o
 endif
+cflatobjs += riscv/sbi-asm.o
 
 ########################################
 
@@ -80,7 +81,7 @@ CFLAGS += -mcmodel=medany
 CFLAGS += -std=gnu99
 CFLAGS += -ffreestanding
 CFLAGS += -O2
-CFLAGS += -I $(SRCDIR)/lib -I $(SRCDIR)/lib/libfdt -I lib
+CFLAGS += -I $(SRCDIR)/lib -I $(SRCDIR)/lib/libfdt -I lib -I $(SRCDIR)/riscv
 
 asm-offsets = lib/riscv/asm-offsets.h
 include $(SRCDIR)/scripts/asm-offsets.mak
riscv/sbi-tests.h new file +10 -0
new file mode 100644
index 00000000..f5cc8635
@@ -0,0 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+#ifndef _RISCV_SBI_TESTS_H_
+#define _RISCV_SBI_TESTS_H_
+
+#define SBI_HSM_TEST_DONE	(1 << 0)
+#define SBI_HSM_TEST_HARTID_A1	(1 << 1)
+#define SBI_HSM_TEST_SATP	(1 << 2)
+#define SBI_HSM_TEST_SIE	(1 << 3)
+
+#endif /* _RISCV_SBI_TESTS_H_ */
riscv/sbi-asm.S new file +71 -0

71 lines not on this page · raw message

riscv/sbi.c +5 -0
index a7abc08c..d4dfd48e 100644
@@ -18,6 +18,7 @@
 #include <asm/mmu.h>
 #include <asm/processor.h>
 #include <asm/sbi.h>
+#include <asm/setup.h>
 #include <asm/smp.h>
 #include <asm/timer.h>
 
@@ -288,6 +289,10 @@ static void check_time(void)
 	report_prefix_popn(2);
 }
 
+unsigned char sbi_hsm_stop_hart[NR_CPUS];
+unsigned char sbi_hsm_hart_start_checks[NR_CPUS];
+unsigned char sbi_hsm_non_retentive_hart_suspend_checks[NR_CPUS];
+
 #define DBCN_WRITE_TEST_STRING		"DBCN_WRITE_TEST_STRING\n"
 #define DBCN_WRITE_BYTE_TEST_BYTE	((u8)'a')
 
Signature · 1 line
2.43.0
#4 lore raw

PATCH v4 3/3 riscv: sbi: Add tests for HSM extension

In reply to James Raphael Tiovalen

Add some tests for all of the HSM extension functions. These tests ensure that the HSM extension functions follow the behavior as described in the SBI specification.

---
 riscv/sbi.h |  10 +
 riscv/sbi.c | 561 ++++++++++++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 571 insertions(+)
 create mode 100644 riscv/sbi.h
riscv/sbi.h new file +10 -0
new file mode 100644
index 00000000..e8625cb1
@@ -0,0 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+#ifndef _RISCV_SBI_H_
+#define _RISCV_SBI_H_
+
+#define SBI_HSM_TEST_DONE	(1 << 0)
+#define SBI_HSM_TEST_SATP	(1 << 1)
+#define SBI_HSM_TEST_SIE	(1 << 2)
+#define SBI_HSM_TEST_HARTID_A1	(1 << 3)
+
+#endif /* _RISCV_SBI_H_ */
riscv/sbi.c +561 -0

596 lines not on this page · raw message

Signature · 1 line
2.43.0
#5 lore raw

Re: [kvm-unit-tests PATCH v4 3/3] riscv: sbi: Add tests for HSM extension

Quoted 17 lines · James Raphael Tiovalen

Add some tests for all of the HSM extension functions. These tests ensure that the HSM extension functions follow the behavior as described in the SBI specification.

---
 riscv/sbi.h |  10 +
 riscv/sbi.c | 561 ++++++++++++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 571 insertions(+)
 create mode 100644 riscv/sbi.h
riscv/sbi.h new file +0 -0
new file mode 100644
index 00000000..e8625cb1

riscv/sbi.h line 10

Quoted 10 lines
riscv/sbi.h new file +10 -0
@@ -0,0 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+#ifndef _RISCV_SBI_H_
+#define _RISCV_SBI_H_
+
+#define SBI_HSM_TEST_DONE	(1 << 0)
+#define SBI_HSM_TEST_SATP	(1 << 1)
+#define SBI_HSM_TEST_SIE	(1 << 2)
+#define SBI_HSM_TEST_HARTID_A1	(1 << 3)
+
+#endif /* _RISCV_SBI_H_ */

The last patch creates riscv/sbi-tests.h for this, so we don't want this file.

Quoted 14 lines
riscv/sbi.c +2 -0
index d4dfd48e..fab0091b 100644
@@ -6,6 +6,8 @@
  */
 #include <libcflat.h>
 #include <alloc_page.h>
+#include <cpumask.h>
+#include <on-cpus.h>
 #include <stdlib.h>
 #include <string.h>
 #include <limits.h>

riscv/sbi.c line 27

Quoted 10 lines
riscv/sbi.c +2 -0
@@ -16,11 +18,13 @@
 #include <asm/delay.h>
 #include <asm/io.h>
 #include <asm/mmu.h>
+#include <asm/page.h>
 #include <asm/processor.h>
 #include <asm/sbi.h>
 #include <asm/setup.h>
 #include <asm/smp.h>
 #include <asm/timer.h>
+#include <sbi.h>

This should be

#include "sbi-tests.h"

and have a blank line between the last <> include and it. See how it's included in sbi-asm.S.

(I renamed it to sbi-tests.h and use "" since I want it to be clear that it isn't part of the library. Headers included like <sbi.h> would normally be in lib.)

Quoted 16 lines
riscv/sbi.c +5 -0
 #define	HIGH_ADDR_BOUNDARY	((phys_addr_t)1 << 32)
 
@@ -47,6 +51,11 @@ static struct sbiret sbi_dbcn_write_byte(uint8_t byte)
 	return sbi_ecall(SBI_EXT_DBCN, SBI_EXT_DBCN_CONSOLE_WRITE_BYTE, byte, 0, 0, 0, 0, 0);
 }
 
+static struct sbiret sbi_hart_suspend(uint32_t suspend_type, unsigned long resume_addr, unsigned long opaque)
+{
+	return sbi_ecall(SBI_EXT_HSM, SBI_EXT_HSM_HART_SUSPEND, suspend_type, resume_addr, opaque, 0, 0, 0);
+}
+
 static void split_phys_addr(phys_addr_t paddr, unsigned long *hi, unsigned long *lo)
 {
 	*lo = (unsigned long)paddr;

riscv/sbi.c static void check_dbcn(void) · line 448

Quoted 6 lines
riscv/sbi.c +3 -0
@@ -434,6 +443,557 @@ static void check_dbcn(void)
 	report_prefix_popn(2);
 }
 
+unsigned char sbi_hsm_stop_hart[NR_CPUS];
+unsigned char sbi_hsm_hart_start_checks[NR_CPUS];
+unsigned char sbi_hsm_non_retentive_hart_suspend_checks[NR_CPUS];

These were added in the first patch of this series. So they must be getting added again somehow?

Quoted 33 lines
riscv/sbi.c +33 -0
+cpumask_t sbi_hsm_started_hart_checks;
+cpumask_t sbi_hsm_invalid_hartid_checks;
+static bool hsm_timer_fired;
+extern void sbi_hsm_check_hart_start(void);
+extern void sbi_hsm_check_non_retentive_suspend(void);
+
+static void hsm_timer_irq_handler(struct pt_regs *regs)
+{
+	hsm_timer_fired = true;
+	timer_stop();
+}
+
+static void hsm_timer_setup(void)
+{
+	install_irq_handler(IRQ_S_TIMER, hsm_timer_irq_handler);
+	local_irq_enable();
+	timer_irq_enable();
+}
+
+static void hsm_timer_teardown(void)
+{
+	timer_irq_disable();
+	local_irq_disable();
+	install_irq_handler(IRQ_S_TIMER, NULL);
+}
+
+static void hart_empty_fn(void *data) {}
+
+static void hart_execute(void *data)
+{
+	struct sbiret ret;
+	unsigned long hartid = current_thread_info()->hartid;
+	int me = smp_processor_id();

riscv/sbi.c static void check_dbcn(void) · line 491

Quoted 10 lines
riscv/sbi.c +10 -0
+
+	ret = sbi_hart_start(hartid, virt_to_phys(&hart_empty_fn), 0);
+
+	if (ret.error == SBI_ERR_ALREADY_AVAILABLE)
+		cpumask_set_cpu(me, &sbi_hsm_started_hart_checks);
+
+	ret = sbi_hart_start(ULONG_MAX, virt_to_phys(&hart_empty_fn), 0);
+
+	if (ret.error == SBI_ERR_INVALID_PARAM)
+		cpumask_set_cpu(me, &sbi_hsm_invalid_hartid_checks);

This is a good tests, but I'm not sure why we give the 'me' hart credit for it since we weren't using the 'me' hart's hartid in the test. The invalid hartid test should just be an independent test.

Quoted 34 lines
riscv/sbi.c +34 -0
+}
+
+static void hart_retentive_suspend(void *data)
+{
+	unsigned long hartid = current_thread_info()->hartid;
+	struct sbiret ret = sbi_hart_suspend(SBI_EXT_HSM_HART_SUSPEND_RETENTIVE, 0, 0);
+
+	if (ret.error)
+		report_fail("failed to retentive suspend hart %ld (error=%ld)", hartid, ret.error);
+}
+
+static void hart_non_retentive_suspend(void *data)
+{
+	unsigned long hartid = current_thread_info()->hartid;
+
+	/* Set opaque as hartid so that we can check a0 == a1, ensuring that a0 is hartid and a1 is opaque */
+	struct sbiret ret = sbi_hart_suspend(SBI_EXT_HSM_HART_SUSPEND_NON_RETENTIVE,
+					     virt_to_phys(&sbi_hsm_check_non_retentive_suspend), hartid);
+
+	report_fail("failed to non-retentive suspend hart %ld (error=%ld)", hartid, ret.error);
+}
+
+static void hart_wait_on_status(unsigned long hartid, enum sbi_ext_hsm_sid status)
+{
+	struct sbiret ret = sbi_hart_get_status(hartid);
+
+	while (!ret.error && ret.value == status && !hsm_timer_fired) {
+		cpu_relax();
+		ret = sbi_hart_get_status(hartid);
+	}
+
+	if (hsm_timer_fired)
+		report_info("timer fired while waiting on status %u for hart %ld", status, hartid);
+	else if (ret.error)

riscv/sbi.c static void check_dbcn(void) · line 535

Quoted 10 lines
riscv/sbi.c +10 -0
+		report_fail("got %ld while waiting on status %u for hart %ld\n", ret.error, status, hartid);
+}
+
+static void check_hsm(void)
+{
+	struct sbiret ret;
+	unsigned long hartid;
+	cpumask_t secondary_cpus_mask, hsm_start, hsm_stop, hsm_suspend, hsm_resume, hsm_check;
+	int cpu, me = smp_processor_id();
+	int max_cpu = getenv("SBI_HSM_MAX_CPU") ? strtol(getenv("SBI_HSM_MAX_CPU"), NULL, 0) : INT_MAX;

I think it'll be better if this is named SBI_MAX_CPUS and is the maximum _number_ of cpus that the SBI implementation supports.

And max_cpus should default to nr_cpus, so we should have

int max_cpus = getenv("SBI_MAX_CPUS") ? strtol(getenv("SBI_MAX_CPUS"), NULL, 0) : nr_cpus;

riscv/sbi.c static void check_dbcn(void) · line 539

Quoted 4 lines
riscv/sbi.c +4 -0
+	unsigned long hsm_timer_duration = getenv("SBI_HSM_TIMER_DURATION")
+					 ? strtol(getenv("SBI_HSM_TIMER_DURATION"), NULL, 0) : 200000;
+
+	max_cpu = MIN(max_cpu, nr_cpus - 1);

And here we would have

	max_cpus = MIN(max_cpus, nr_cpus);

and if we still need 'max_cpu' (the highest cpu id), like we do below, then we'll get it with 'max_cpus - 1'.

riscv/sbi.c static void check_dbcn(void) · line 544

Quoted 5 lines
riscv/sbi.c +5 -0
+
+	cpumask_copy(&secondary_cpus_mask, &cpu_present_mask);
+	cpumask_clear_cpu(me, &secondary_cpus_mask);
+	for_each_cpu(cpu, &secondary_cpus_mask)
+		if (cpu > max_cpu)

if (cpu > max_cpus - 1)

Quoted 20 lines
riscv/sbi.c +20 -0
+			cpumask_clear_cpu(cpu, &secondary_cpus_mask);
+
+	report_prefix_push("hsm");
+
+	if (!sbi_probe(SBI_EXT_HSM)) {
+		report_skip("hsm extension not available");
+		report_prefix_pop();
+		return;
+	}
+
+	report_prefix_push("hart_get_status");
+
+	hartid = current_thread_info()->hartid;
+	ret = sbi_hart_get_status(hartid);
+
+	if (ret.error) {
+		report_fail("failed to get status of current hart (error=%ld)", ret.error);
+		report_prefix_popn(2);
+		return;
+	} else if (ret.value != SBI_EXT_HSM_STARTED) {

riscv/sbi.c static void check_dbcn(void) · line 574

Quoted 10 lines
riscv/sbi.c +10 -0
+		report_fail("current hart is not started (ret.value=%ld)", ret.value);
+		report_prefix_popn(2);
+		return;
+	}
+
+	report_pass("status of current hart is started");
+
+	report_prefix_pop();
+
+	if (max_cpu + 1 < 2) {

if (max_cpus < 2)

riscv/sbi.c static void check_dbcn(void) · line 582

Quoted 8 lines
riscv/sbi.c +8 -0
+		report_skip("no other cpus to run the remaining hsm tests on");
+		report_prefix_pop();
+		return;
+	}
+
+	/* This is necessary since we do not choose which cpu the boot hart will run on */
+	if (me > max_cpu)
+		max_cpu++;

Hmm, I see an issue here. If a DT has its CPU nodes in an order where nodes earlier in the list include hartids which are not activated by the SBI implementation due to the SBI implementation's limits on the number of harts it can activate (because the SBI implementation chose to activate harts in a particular hartid order rather than by DT cpu node order), then simply clamping nr_cpus down to SBI max_cpus will not work. We need to instead run the cpu_present_mask through a filter to remove all the cpus corresponding to hartids which the SBI implementation has not activated. This is something we should do in setup(), so I just wrote a patch for it now [1]. With that patch the

  for_each_cpu(cpu, &secondary_cpus_mask)
     if (cpu > max_cpu)
          cpumask_clear_cpu(cpu, &secondary_cpus_mask);

loop above should be removed. The

    cpumask_copy(&secondary_cpus_mask, &cpu_present_mask);
    cpumask_clear_cpu(me, &secondary_cpus_mask);

is sufficient for getting a valid mask of cpus that SBI manages. And of course no need for this

if (me > max_cpu)

     max_cpu++;

which was insufficient anyway since 'me' doesn't necessarily have to be just one more than the expected max cpuid.

[1] https://gitlab.com/jones-drew/kvm-unit-tests/-/commit/5fc2c49c6ee37ab725dc0f7a0f6858c17705604f

riscv/sbi.c static void check_dbcn(void) · line 593

Quoted 11 lines
riscv/sbi.c +11 -0
+
+	report_prefix_push("hart_start");
+
+	for_each_cpu(cpu, &secondary_cpus_mask) {
+		hartid = cpus[cpu].hartid;
+		/* Set opaque as hartid so that we can check a0 == a1, ensuring that a0 is hartid and a1 is opaque */
+		ret = sbi_hart_start(hartid, virt_to_phys(&sbi_hsm_check_hart_start), hartid);
+		if (ret.error) {
+			report_fail("failed to start test hart %ld (error=%ld)", hartid, ret.error);
+			report_prefix_popn(2);
+			return;

Do we need to give up on all tests if one hart fails to start?

riscv/sbi.c static void check_dbcn(void) · line 594

Quoted 1 line
riscv/sbi.c +1 -0
+		}

We should move the sbi_hart_start call into the loop below so we can time each start/wait individually.

riscv/sbi.c static void check_dbcn(void) · line 599

Quoted 5 lines
riscv/sbi.c +5 -0
+	}
+
+	cpumask_clear(&hsm_start);
+	hsm_timer_setup();
+	timer_start(hsm_timer_duration);

Duration should be small, so we don't want to put a timer_start outside the loop. It should instead be...

riscv/sbi.c static void check_dbcn(void) · line 587

Quoted 3 lines
riscv/sbi.c +3 -0
+
+	for_each_cpu(cpu, &secondary_cpus_mask) {
+		hartid = cpus[cpu].hartid;

...here and...

riscv/sbi.c static void check_dbcn(void) · line 603

Quoted 1 line
riscv/sbi.c +1 -0
+		hart_wait_on_status(hartid, SBI_EXT_HSM_STOPPED);

...here should be a timer_stop().

riscv/sbi.c static void check_dbcn(void) · line 605

Quoted 2 lines
riscv/sbi.c +2 -0
+		if (hsm_timer_fired)
+			break;

Other timer_start here

riscv/sbi.c static void check_dbcn(void) · line 606

Quoted 1 line
riscv/sbi.c +1 -0
+		hart_wait_on_status(hartid, SBI_EXT_HSM_START_PENDING);

and stop here. Actually we can put timer_start/stop in hart_wait_on_status().

Quoted 6 lines
riscv/sbi.c +6 -0
+		if (hsm_timer_fired)
+			break;
+		ret = sbi_hart_get_status(hartid);
+		if (ret.error)
+			report_info("hart %ld get status failed (error=%ld)", hartid, ret.error);
+		else if (ret.value != SBI_EXT_HSM_STARTED)

riscv/sbi.c static void check_dbcn(void) · line 622

Quoted 10 lines
riscv/sbi.c +10 -0
+			report_info("hart %ld status is not 'started' (ret.value=%ld)", hartid, ret.value);
+		else
+			cpumask_set_cpu(cpu, &hsm_start);
+	}
+
+	if (hsm_timer_fired) {
+		hsm_timer_teardown();
+		report_fail("hsm timer fired before all secondary harts started");
+		report_prefix_popn(2);
+		return;

Do we need to give up on all test if some harts fail?

riscv/sbi.c static void check_dbcn(void) · line 631

Quoted 9 lines
riscv/sbi.c +9 -0
+	}
+
+	report(cpumask_weight(&hsm_start) == max_cpu, "all secondary harts started");
+
+	cpumask_clear(&hsm_check);
+
+	for_each_cpu(cpu, &secondary_cpus_mask) {
+		hartid = cpus[cpu].hartid;
+

timer_start

riscv/sbi.c static void check_dbcn(void) · line 633

Quoted 2 lines
riscv/sbi.c +2 -0
+		while (!(READ_ONCE(sbi_hsm_hart_start_checks[cpu]) & SBI_HSM_TEST_DONE) && !hsm_timer_fired)
+			cpu_relax();

timer_stop

riscv/sbi.c static void check_dbcn(void) · line 645

Quoted 12 lines
riscv/sbi.c +12 -0
+
+		if (hsm_timer_fired)
+			break;
+
+		if (!(sbi_hsm_hart_start_checks[cpu] & SBI_HSM_TEST_SATP))
+			report_info("satp is not zero for test hart %ld", hartid);
+		else if (!(sbi_hsm_hart_start_checks[cpu] & SBI_HSM_TEST_SIE))
+			report_info("sstatus.SIE is not zero for test hart %ld", hartid);
+		else if (!(sbi_hsm_hart_start_checks[cpu] & SBI_HSM_TEST_HARTID_A1))
+			report_info("either a0 or a1 is not hartid for test hart %ld", hartid);
+		else
+			cpumask_set_cpu(cpu, &hsm_check);

The body of this loop can also be merged with the loop above. There should be only one loop that does, start, wait, check for each hart allowing us to time the wait for each hart individually. One the hart the fails to start within duration will fail its start test and we try each to see if others fail or not.

After the loop completes we can output all the

report(cpumask_weight(...

checks.

riscv/sbi.c static void check_dbcn(void) · line 652

Quoted 7 lines
riscv/sbi.c +7 -0
+	}
+
+	if (hsm_timer_fired) {
+		hsm_timer_teardown();
+		report_fail("hsm timer fired before all secondary harts are done with checks");
+		report_prefix_popn(2);
+		return;

Do we need to give up on all test if some harts fail?

Quoted 6 lines
riscv/sbi.c +6 -0
+	}
+
+	timer_stop();
+
+	report(cpumask_weight(&hsm_check) == max_cpu,
+	       "all secondary harts have expected register values after hart start");

riscv/sbi.c static void check_dbcn(void) · line 668

Quoted 10 lines
riscv/sbi.c +10 -0
+
+	report_prefix_pop();
+
+	report_prefix_push("hart_stop");
+
+	memset(sbi_hsm_stop_hart, 1, sizeof(sbi_hsm_stop_hart));
+
+	cpumask_clear(&hsm_stop);
+	hsm_timer_fired = false;
+	timer_start(hsm_timer_duration);

move timer_start/top into hart_wait_on_status.

Quoted 13 lines
riscv/sbi.c +13 -0
+
+	for_each_cpu(cpu, &secondary_cpus_mask) {
+		hartid = cpus[cpu].hartid;
+		hart_wait_on_status(hartid, SBI_EXT_HSM_STARTED);
+		if (hsm_timer_fired)
+			break;
+		hart_wait_on_status(hartid, SBI_EXT_HSM_STOP_PENDING);
+		if (hsm_timer_fired)
+			break;
+		ret = sbi_hart_get_status(hartid);
+		if (ret.error)
+			report_info("hart %ld get status failed (error=%ld)", hartid, ret.error);
+		else if (ret.value != SBI_EXT_HSM_STOPPED)

riscv/sbi.c static void check_dbcn(void) · line 691

Quoted 10 lines
riscv/sbi.c +10 -0
+			report_info("hart %ld status is not 'stopped' (ret.value=%ld)", hartid, ret.value);
+		else
+			cpumask_set_cpu(cpu, &hsm_stop);
+	}
+
+	if (hsm_timer_fired) {
+		hsm_timer_teardown();
+		report_fail("hsm timer fired before all secondary harts stopped");
+		report_prefix_popn(2);
+		return;

Do we need to give up on all test if some harts fail?

Quoted 8 lines
riscv/sbi.c +8 -0
+	}
+
+	timer_stop();
+
+	report(cpumask_weight(&hsm_stop) == max_cpu, "all secondary harts stopped");
+
+	/* Reset the stop flags so that we can reuse them after suspension tests */
+	memset(sbi_hsm_stop_hart, 0, sizeof(sbi_hsm_stop_hart));

riscv/sbi.c static void check_dbcn(void) · line 709

Quoted 10 lines
riscv/sbi.c +10 -0
+
+	report_prefix_pop();
+
+	report_prefix_push("hart_start");
+
+	on_cpumask_async(&secondary_cpus_mask, hart_execute, NULL);
+
+	cpumask_clear(&hsm_start);
+	hsm_timer_fired = false;
+	timer_start(hsm_timer_duration);

move timer_start/top into hart_wait_on_status

Quoted 13 lines
riscv/sbi.c +13 -0
+
+	for_each_cpu(cpu, &secondary_cpus_mask) {
+		hartid = cpus[cpu].hartid;
+		hart_wait_on_status(hartid, SBI_EXT_HSM_STOPPED);
+		if (hsm_timer_fired)
+			break;
+		hart_wait_on_status(hartid, SBI_EXT_HSM_START_PENDING);
+		if (hsm_timer_fired)
+			break;
+		ret = sbi_hart_get_status(hartid);
+		if (ret.error)
+			report_info("hart %ld get status failed (error=%ld)", hartid, ret.error);
+		else if (ret.value != SBI_EXT_HSM_STARTED)

riscv/sbi.c static void check_dbcn(void) · line 622

Quoted 10 lines
riscv/sbi.c +10 -0
+			report_info("hart %ld status is not 'started' (ret.value=%ld)", hartid, ret.value);
+		else
+			cpumask_set_cpu(cpu, &hsm_start);
+	}
+
+	if (hsm_timer_fired) {
+		hsm_timer_teardown();
+		report_fail("hsm timer fired before all secondary harts started");
+		report_prefix_popn(2);
+		return;

Do we need to give up on all test if some harts fail?

riscv/sbi.c static void check_dbcn(void) · line 626

Quoted 4 lines
riscv/sbi.c +4 -0
+	}
+
+	report(cpumask_weight(&hsm_start) == max_cpu, "all secondary harts started");
+

timer_start

riscv/sbi.c static void check_dbcn(void) · line 738

Quoted 2 lines
riscv/sbi.c +2 -0
+	while (cpumask_weight(&cpu_idle_mask) != max_cpu && !hsm_timer_fired)
+		cpu_relax();

timer_stop

Quoted 24 lines
riscv/sbi.c +24 -0
+
+	if (hsm_timer_fired) {
+		hsm_timer_teardown();
+		report_fail("hsm timer fired before all secondary harts started");
+		report_prefix_popn(2);
+		return;
+	}
+
+	timer_stop();
+
+	report(cpumask_weight(&cpu_idle_mask) == max_cpu,
+	       "all secondary harts successfully executed code after start");
+	report(cpumask_weight(&cpu_online_mask) == max_cpu + 1, "all secondary harts online");
+	report(cpumask_weight(&sbi_hsm_started_hart_checks) == max_cpu,
+	       "all secondary harts are already started");
+	report(cpumask_weight(&sbi_hsm_invalid_hartid_checks) == max_cpu,
+	       "all secondary harts refuse to start with invalid hartid");
+
+	report_prefix_pop();
+
+	report_prefix_push("hart_suspend");
+
+	if (!sbi_probe(SBI_EXT_IPI)) {
+		hsm_timer_teardown();

riscv/sbi.c static void check_dbcn(void) · line 772

Quoted 10 lines
riscv/sbi.c +10 -0
+		report_skip("skipping suspension tests since ipi extension is unavailable");
+		report_prefix_popn(2);
+		return;
+	}
+
+	on_cpumask_async(&secondary_cpus_mask, hart_retentive_suspend, NULL);
+
+	cpumask_clear(&hsm_suspend);
+	hsm_timer_fired = false;
+	timer_start(hsm_timer_duration);

move timer_start/top into hart_wait_on_status

Quoted 13 lines
riscv/sbi.c +13 -0
+
+	for_each_cpu(cpu, &secondary_cpus_mask) {
+		hartid = cpus[cpu].hartid;
+		hart_wait_on_status(hartid, SBI_EXT_HSM_STARTED);
+		if (hsm_timer_fired)
+			break;
+		hart_wait_on_status(hartid, SBI_EXT_HSM_SUSPEND_PENDING);
+		if (hsm_timer_fired)
+			break;
+		ret = sbi_hart_get_status(hartid);
+		if (ret.error)
+			report_info("hart %ld get status failed (error=%ld)", hartid, ret.error);
+		else if (ret.value != SBI_EXT_HSM_SUSPENDED)

riscv/sbi.c static void check_dbcn(void) · line 795

Quoted 10 lines
riscv/sbi.c +10 -0
+			report_info("hart %ld status is not 'suspended' (ret.value=%ld)", hartid, ret.value);
+		else
+			cpumask_set_cpu(cpu, &hsm_suspend);
+	}
+
+	if (hsm_timer_fired) {
+		hsm_timer_teardown();
+		report_fail("hsm timer fired before all secondary harts retentive suspended");
+		report_prefix_popn(2);
+		return;

Do we need to give up on all test if some harts fail?

riscv/sbi.c static void check_dbcn(void) · line 807

Quoted 12 lines
riscv/sbi.c +12 -0
+	}
+
+	timer_stop();
+
+	report(cpumask_weight(&hsm_suspend) == max_cpu, "all secondary harts retentive suspended");
+
+	ret = sbi_send_ipi_cpumask(&secondary_cpus_mask);
+
+	if (!ret.error) {
+		cpumask_clear(&hsm_resume);
+		hsm_timer_fired = false;
+		timer_start(hsm_timer_duration);

move timer_start/top into hart_wait_on_status

Quoted 13 lines
riscv/sbi.c +13 -0
+
+		for_each_cpu(cpu, &secondary_cpus_mask) {
+			hartid = cpus[cpu].hartid;
+			hart_wait_on_status(hartid, SBI_EXT_HSM_SUSPENDED);
+			if (hsm_timer_fired)
+				break;
+			hart_wait_on_status(hartid, SBI_EXT_HSM_RESUME_PENDING);
+			if (hsm_timer_fired)
+				break;
+			ret = sbi_hart_get_status(hartid);
+			if (ret.error)
+				report_info("hart %ld get status failed (error=%ld)", hartid, ret.error);
+			else if (ret.value != SBI_EXT_HSM_STARTED)

riscv/sbi.c static void check_dbcn(void) · line 830

Quoted 10 lines
riscv/sbi.c +10 -0
+				report_info("hart %ld status is not 'started' (ret.value=%ld)", hartid, ret.value);
+			else
+				cpumask_set_cpu(cpu, &hsm_resume);
+		}
+
+		if (hsm_timer_fired) {
+			hsm_timer_teardown();
+			report_fail("hsm timer fired before all secondary harts retentive resumed");
+			report_prefix_popn(2);
+			return;

Do we need to give up on all test if some harts fail?

riscv/sbi.c static void check_dbcn(void) · line 834

Quoted 4 lines
riscv/sbi.c +4 -0
+		}
+
+		report(cpumask_weight(&hsm_resume) == max_cpu, "all secondary harts retentive resumed");
+

timer_start

riscv/sbi.c static void check_dbcn(void) · line 836

Quoted 2 lines
riscv/sbi.c +2 -0
+		while (cpumask_weight(&cpu_idle_mask) != max_cpu && !hsm_timer_fired)
+			cpu_relax();

timer_stop

riscv/sbi.c static void check_dbcn(void) · line 830

Quoted 6 lines
riscv/sbi.c +6 -0
+
+		if (hsm_timer_fired) {
+			hsm_timer_teardown();
+			report_fail("hsm timer fired before all secondary harts retentive resumed");
+			report_prefix_popn(2);
+			return;

Do we need to give up on all test if some harts fail?

Quoted 4 lines
riscv/sbi.c +4 -0
+		}
+
+		timer_stop();
+

riscv/sbi.c static void check_dbcn(void) · line 856

Quoted 10 lines
riscv/sbi.c +10 -0
+		report(cpumask_weight(&cpu_idle_mask) == max_cpu,
+		       "all secondary harts successfully executed code after retentive suspend");
+		report(cpumask_weight(&cpu_online_mask) == max_cpu + 1,
+		       "all secondary harts online");
+	}
+
+	on_cpumask_async(&secondary_cpus_mask, hart_non_retentive_suspend, NULL);
+
+	cpumask_clear(&hsm_suspend);
+	hsm_timer_fired = false;

move timer_start/top into hart_wait_on_status

Quoted 14 lines
riscv/sbi.c +14 -0
+	timer_start(hsm_timer_duration);
+
+	for_each_cpu(cpu, &secondary_cpus_mask) {
+		hartid = cpus[cpu].hartid;
+		hart_wait_on_status(hartid, SBI_EXT_HSM_STARTED);
+		if (hsm_timer_fired)
+			break;
+		hart_wait_on_status(hartid, SBI_EXT_HSM_SUSPEND_PENDING);
+		if (hsm_timer_fired)
+			break;
+		ret = sbi_hart_get_status(hartid);
+		if (ret.error)
+			report_info("hart %ld get status failed (error=%ld)", hartid, ret.error);
+		else if (ret.value != SBI_EXT_HSM_SUSPENDED)

riscv/sbi.c static void check_dbcn(void) · line 880

Quoted 10 lines
riscv/sbi.c +10 -0
+			report_info("hart %ld status is not 'suspended' (ret.value=%ld)", hartid, ret.value);
+		else
+			cpumask_set_cpu(cpu, &hsm_suspend);
+	}
+
+	if (hsm_timer_fired) {
+		hsm_timer_teardown();
+		report_fail("hsm timer fired before all secondary harts non-retentive suspended");
+		report_prefix_popn(2);
+		return;

Do we need to give up on all test if some harts fail?

riscv/sbi.c static void check_dbcn(void) · line 892

Quoted 12 lines
riscv/sbi.c +12 -0
+	}
+
+	timer_stop();
+
+	report(cpumask_weight(&hsm_suspend) == max_cpu, "all secondary harts non-retentive suspended");
+
+	ret = sbi_send_ipi_cpumask(&secondary_cpus_mask);
+
+	if (!ret.error) {
+		cpumask_clear(&hsm_resume);
+		hsm_timer_fired = false;
+		timer_start(hsm_timer_duration);

move timer_start/top into hart_wait_on_status

Quoted 13 lines
riscv/sbi.c +13 -0
+
+		for_each_cpu(cpu, &secondary_cpus_mask) {
+			hartid = cpus[cpu].hartid;
+			hart_wait_on_status(hartid, SBI_EXT_HSM_SUSPENDED);
+			if (hsm_timer_fired)
+				break;
+			hart_wait_on_status(hartid, SBI_EXT_HSM_RESUME_PENDING);
+			if (hsm_timer_fired)
+				break;
+			ret = sbi_hart_get_status(hartid);
+			if (ret.error)
+				report_info("hart %ld get status failed (error=%ld)", hartid, ret.error);
+			else if (ret.value != SBI_EXT_HSM_STARTED)

riscv/sbi.c static void check_dbcn(void) · line 915

Quoted 10 lines
riscv/sbi.c +10 -0
+				report_info("hart %ld status is not 'started' (ret.value=%ld)", hartid, ret.value);
+			else
+				cpumask_set_cpu(cpu, &hsm_resume);
+		}
+
+		if (hsm_timer_fired) {
+			hsm_timer_teardown();
+			report_fail("hsm timer fired before all secondary harts non-retentive resumed");
+			report_prefix_popn(2);
+			return;

Do we need to give up on all test if some harts fail?

riscv/sbi.c static void check_dbcn(void) · line 924

Quoted 9 lines
riscv/sbi.c +9 -0
+		}
+
+		report(cpumask_weight(&hsm_resume) == max_cpu, "all secondary harts non-retentive resumed");
+
+		cpumask_clear(&hsm_check);
+
+		for_each_cpu(cpu, &secondary_cpus_mask) {
+			hartid = cpus[cpu].hartid;
+

timer_start

riscv/sbi.c static void check_dbcn(void) · line 927

Quoted 3 lines
riscv/sbi.c +3 -0
+			while (!((READ_ONCE(sbi_hsm_non_retentive_hart_suspend_checks[cpu])) & SBI_HSM_TEST_DONE)
+			       && !hsm_timer_fired)
+				cpu_relax();

timer_stop

Quoted 9 lines
riscv/sbi.c +9 -0
+
+			if (hsm_timer_fired)
+				break;
+
+			if (!(sbi_hsm_non_retentive_hart_suspend_checks[cpu] & SBI_HSM_TEST_SATP))
+				report_info("satp is not zero for test hart %ld", hartid);
+			else if (!(sbi_hsm_non_retentive_hart_suspend_checks[cpu] & SBI_HSM_TEST_SIE))
+				report_info("sstatus.SIE is not zero for test hart %ld", hartid);
+			else if (!(sbi_hsm_non_retentive_hart_suspend_checks[cpu] & SBI_HSM_TEST_HARTID_A1))

riscv/sbi.c static void check_dbcn(void) · line 946

Quoted 10 lines
riscv/sbi.c +10 -0
+				report_info("either a0 or a1 is not hartid for test hart %ld", hartid);
+			else
+				cpumask_set_cpu(cpu, &hsm_check);
+		}
+
+		if (hsm_timer_fired) {
+			hsm_timer_teardown();
+			report_fail("hsm timer fired before all secondary harts are done with checks");
+			report_prefix_popn(2);
+			return;

Do we need to give up on all test if some harts fail?

Quoted 6 lines
riscv/sbi.c +6 -0
+		}
+
+		timer_stop();
+
+		report(cpumask_weight(&hsm_check) == max_cpu,
+		       "all secondary harts have expected register values after non-retentive resume");

riscv/sbi.c static void check_dbcn(void) · line 962

Quoted 10 lines
riscv/sbi.c +10 -0
+
+		report_prefix_pop();
+
+		report_prefix_push("hart_stop");
+
+		memset(sbi_hsm_stop_hart, 1, sizeof(sbi_hsm_stop_hart));
+
+		cpumask_clear(&hsm_stop);
+		hsm_timer_fired = false;
+		timer_start(hsm_timer_duration);

move timer_start/top into hart_wait_on_status

Quoted 13 lines
riscv/sbi.c +13 -0
+
+		for_each_cpu(cpu, &secondary_cpus_mask) {
+			hartid = cpus[cpu].hartid;
+			hart_wait_on_status(hartid, SBI_EXT_HSM_STARTED);
+			if (hsm_timer_fired)
+				break;
+			hart_wait_on_status(hartid, SBI_EXT_HSM_STOP_PENDING);
+			if (hsm_timer_fired)
+				break;
+			ret = sbi_hart_get_status(hartid);
+			if (ret.error)
+				report_info("hart %ld get status failed (error=%ld)", hartid, ret.error);
+			else if (ret.value != SBI_EXT_HSM_STOPPED)

riscv/sbi.c static void check_dbcn(void) · line 985

Quoted 10 lines
riscv/sbi.c +10 -0
+				report_info("hart %ld status is not 'stopped' (ret.value=%ld)", hartid, ret.value);
+			else
+				cpumask_set_cpu(cpu, &hsm_stop);
+		}
+
+		if (hsm_timer_fired) {
+			hsm_timer_teardown();
+			report_fail("hsm timer fired before all secondary harts stopped after resumption");
+			report_prefix_popn(2);
+			return;

Do we need to give up on all test if some harts fail?

Quoted 26 lines
riscv/sbi.c +12 -0
+		}
+
+		timer_stop();
+
+		report(cpumask_weight(&hsm_stop) == max_cpu, "all secondary harts stopped after resumption");
+	}
+
+	hsm_timer_teardown();
+	report_prefix_popn(2);
+}
+
 int main(int argc, char **argv)
 {
 	if (argc > 1 && !strcmp(argv[1], "-h")) {
@@ -444,6 +1004,7 @@ int main(int argc, char **argv)
 	report_prefix_push("sbi");
 	check_base();
 	check_time();
+	check_hsm();
 	check_dbcn();
 
 	return report_summary();
Signature · 1 line
2.43.0

Thanks,
drew

#6 lore raw

Re: [kvm-unit-tests PATCH v4 3/3] riscv: sbi: Add tests for HSM extension

In reply to James Raphael Tiovalen

On Mon, Sep 16, 2024 at 02:34:59AM GMT, James Raphael Tiovalen wrote:
...

riscv/sbi.c static struct sbiret sbi_dbcn_write_byte(uint8_t byte) · line 58

Quoted 5 lines
riscv/sbi.c +5 -0
+static struct sbiret sbi_hart_suspend(uint32_t suspend_type, unsigned long resume_addr, unsigned long opaque)
+{
+	return sbi_ecall(SBI_EXT_HSM, SBI_EXT_HSM_HART_SUSPEND, suspend_type, resume_addr, opaque, 0, 0, 0);
+}
+

It's good to create these wrappers per the spec, i.e. use the parameter name types from the spec to define the wrapper, but we should also remember that if, like in this case, we force a parameter to be of a certain type that we also add tests for when we use input outside the expected range by using a "raw" ecall. See the last test of the DBCN extension where we test a byte write with a word full of data to ensure the SBI call does the right thing. We have to call sbi_ecall() instead of sbi_dbcn_write_byte() to do that because sbi_dbcn_write_byte() has been written to only accept uint8_t input.

So we'll need some sort of test for suspend where we pass a value with high bits set for suspend_type when running the test on rv64.

Thanks,
drew