pressure: bmp280: Minor cleanup and interrupt support

index 6811619c6f11..9ad29cf4c2ac 100644
@@ -16,6 +16,11 @@
  * https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bmp390-ds002.pdf
  * https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bmp581-ds004.pdf
  *
+ * Sensor API:
+ * https://github.com/boschsensortec/BME280_SensorAPI
+ * https://github.com/boschsensortec/BMP3_SensorAPI
+ * https://github.com/boschsensortec/BMP5_SensorAPI
+ *
  * Notice:
  * The link to the bmp180 datasheet points to an outdated version missing these changes:
  * - Changed document referral from ANP015 to BST-MPS-AN004-00 on page 26

@@ -616,6 +621,14 @@ static int bmp280_read_raw_impl(struct iio_dev *indio_dev,
 
 	switch (mask) {
 	case IIO_CHAN_INFO_PROCESSED:
+		ret = data->chip_info->set_mode(data, BMP280_FORCED);
+		if (ret)
+			return ret;
+
+		ret = data->chip_info->wait_conv(data);
+		if (ret)
+			return ret;
+
 		switch (chan->type) {
 		case IIO_HUMIDITYRELATIVE:
 			ret = data->chip_info->read_humid(data, &chan_value);

@@ -645,6 +658,14 @@ static int bmp280_read_raw_impl(struct iio_dev *indio_dev,
 			return -EINVAL;
 		}
 	case IIO_CHAN_INFO_RAW:
+		ret = data->chip_info->set_mode(data, BMP280_FORCED);
+		if (ret)
+			return ret;
+
+		ret = data->chip_info->wait_conv(data);
+		if (ret)
+			return ret;
+
 		switch (chan->type) {
 		case IIO_HUMIDITYRELATIVE:
 			ret = data->chip_info->read_humid(data, &chan_value);

@@ -991,6 +1012,69 @@ static int bmp280_preinit(struct bmp280_data *data)
 	return 0;
 }
 
+static const u8 bmp280_operation_mode[] = {
+	BMP280_MODE_SLEEP, BMP280_MODE_FORCED, BMP280_MODE_NORMAL,
+};
+
+static int bmp280_set_mode(struct bmp280_data *data, enum bmp280_op_mode mode)
+{
+	int ret;
+
+	switch (mode) {
+	case BMP280_SLEEP:
+	case BMP280_FORCED:
+	case BMP280_NORMAL:
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	ret = regmap_write_bits(data->regmap, BMP280_REG_CTRL_MEAS,
+				BMP280_MODE_MASK, bmp280_operation_mode[mode]);
+	if (ret) {
+		dev_err(data->dev, "failed to  write ctrl_meas register.\n");
+		return ret;
+	}
+
+	data->op_mode = mode;
+
+	return 0;
+}
+
+static int bmp280_wait_conv(struct bmp280_data *data)
+{
+	unsigned int reg, meas_time_us;
+	int ret;
+
+	/* Check if we are using a BME280 device */
+	if (data->oversampling_humid)
+		meas_time_us += BMP280_PRESS_HUMID_MEAS_OFFSET +
+				BIT(data->oversampling_humid) * BMP280_MEAS_DUR;
+
+	/* Pressure measurement time */
+	meas_time_us += BMP280_PRESS_HUMID_MEAS_OFFSET +
+			BIT(data->oversampling_press) * BMP280_MEAS_DUR;
+
+	/* Temperature measurement time */
+	meas_time_us += BIT(data->oversampling_temp) * BMP280_MEAS_DUR;
+
+	/* Waiting time according to the BM(P/E)2 Sensor API */
+	fsleep(meas_time_us);
+
+	ret = regmap_read(data->regmap, BMP280_REG_STATUS, &reg);
+	if (ret) {
+		dev_err(data->dev, "failed to read status register.\n");
+		return ret;
+	}
+
+	if (reg & BMP280_REG_STATUS_MEAS_BIT) {
+		dev_err(data->dev, "Measurement cycle didn't complete.\n");
+		return -EBUSY;
+	}
+
+	return 0;
+}
+
 static int bmp280_chip_config(struct bmp280_data *data)
 {
 	u8 osrs = FIELD_PREP(BMP280_OSRS_TEMP_MASK, data->oversampling_temp + 1) |

@@ -1001,7 +1085,7 @@ static int bmp280_chip_config(struct bmp280_data *data)
 				BMP280_OSRS_TEMP_MASK |
 				BMP280_OSRS_PRESS_MASK |
 				BMP280_MODE_MASK,
-				osrs | BMP280_MODE_NORMAL);
+				osrs | BMP280_MODE_SLEEP);
 	if (ret) {
 		dev_err(data->dev, "failed to write ctrl_meas register\n");
 		return ret;

@@ -1111,6 +1195,8 @@ const struct bmp280_chip_info bmp280_chip_info = {
 	.read_temp = bmp280_read_temp,
 	.read_press = bmp280_read_press,
 	.read_calib = bmp280_read_calib,
+	.set_mode = bmp280_set_mode,
+	.wait_conv = bmp280_wait_conv,
 	.preinit = bmp280_preinit,
 
 	.trigger_handler = bmp280_trigger_handler,

@@ -1235,6 +1321,8 @@ const struct bmp280_chip_info bme280_chip_info = {
 	.read_press = bmp280_read_press,
 	.read_humid = bme280_read_humid,
 	.read_calib = bme280_read_calib,
+	.set_mode = bmp280_set_mode,
+	.wait_conv = bmp280_wait_conv,
 	.preinit = bmp280_preinit,
 
 	.trigger_handler = bme280_trigger_handler,

@@ -1522,6 +1610,71 @@ static int bmp380_preinit(struct bmp280_data *data)
 	return bmp380_cmd(data, BMP380_CMD_SOFT_RESET);
 }
 
+static const u8 bmp380_operation_mode[] = {
+	BMP380_MODE_SLEEP, BMP380_MODE_FORCED, BMP380_MODE_NORMAL,
+};
+
+static int bmp380_set_mode(struct bmp280_data *data, enum bmp280_op_mode mode)
+{
+	int ret;
+
+	switch (mode) {
+	case BMP280_SLEEP:
+	case BMP280_FORCED:
+	case BMP280_NORMAL:
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	ret = regmap_write_bits(data->regmap, BMP380_REG_POWER_CONTROL,
+				BMP380_MODE_MASK,
+				FIELD_PREP(BMP380_MODE_MASK,
+					   bmp380_operation_mode[mode]));
+	if (ret) {
+		dev_err(data->dev, "failed to  write power control register.\n");
+		return ret;
+	}
+
+	data->op_mode = mode;
+
+	return 0;
+}
+
+static int bmp380_wait_conv(struct bmp280_data *data)
+{
+	unsigned int reg;
+	int ret, meas_time_us;
+
+	/* Offset measurement time */
+	meas_time_us = BMP380_MEAS_OFFSET;
+
+	/* Pressure measurement time */
+	meas_time_us += BMP380_PRESS_MEAS_OFFSET +
+		     BIT(data->oversampling_press) * BMP380_MEAS_DUR;
+
+	/* Temperature measurement time */
+	meas_time_us += BMP380_TEMP_MEAS_OFFSET +
+		     BIT(data->oversampling_temp) * BMP380_MEAS_DUR;
+
+	/* Measurement time defined in Datasheet Section 3.9.2 */
+	fsleep(meas_time_us);
+
+	ret = regmap_read(data->regmap, BMP380_REG_STATUS, &reg);
+	if (ret) {
+		dev_err(data->dev, "failed to read status register.\n");
+		return ret;
+	}
+
+	if (!((reg & BMP380_STATUS_DRDY_PRESS_MASK) &&
+	      (reg & BMP380_STATUS_DRDY_TEMP_MASK))) {
+		dev_err(data->dev, "Measurement cycle didn't complete.\n");
+		return -EBUSY;
+	}
+
+	return 0;
+}
+
 static int bmp380_chip_config(struct bmp280_data *data)
 {
 	bool change = false, aux;

@@ -1582,17 +1735,19 @@ static int bmp380_chip_config(struct bmp280_data *data)
 		 * Resets sensor measurement loop toggling between sleep and
 		 * normal operating modes.
 		 */
-		ret = regmap_write_bits(data->regmap, BMP380_REG_POWER_CONTROL,
-					BMP380_MODE_MASK,
-					FIELD_PREP(BMP380_MODE_MASK, BMP380_MODE_SLEEP));
+		ret = bmp380_set_mode(data, BMP280_SLEEP);
 		if (ret) {
 			dev_err(data->dev, "failed to set sleep mode\n");
 			return ret;
 		}
-		usleep_range(2000, 2500);
-		ret = regmap_write_bits(data->regmap, BMP380_REG_POWER_CONTROL,
-					BMP380_MODE_MASK,
-					FIELD_PREP(BMP380_MODE_MASK, BMP380_MODE_NORMAL));
+
+		/*
+		 * According to the BMP3 Sensor API, the sensor needs 5ms
+		 * in order to go to the sleep mode.
+		 */
+		fsleep(5 * USEC_PER_MSEC);
+
+		ret = bmp380_set_mode(data, BMP280_NORMAL);
 		if (ret) {
 			dev_err(data->dev, "failed to set normal mode\n");
 			return ret;

@@ -1618,7 +1773,16 @@ static int bmp380_chip_config(struct bmp280_data *data)
 		}
 	}
 
-	return 0;
+	/* Dummy read to empty data registers. */
+	ret = bmp380_read_press(data, &tmp);
+	if (ret)
+		return ret;
+
+	ret = bmp380_set_mode(data, BMP280_SLEEP);
+	if (ret)
+		dev_err(data->dev, "failed to set sleep mode.\n");
+
+	return ret;
 }
 
 static irqreturn_t bmp380_trigger_handler(int irq, void *p)

@@ -1714,6 +1878,8 @@ const struct bmp280_chip_info bmp380_chip_info = {
 	.read_temp = bmp380_read_temp,
 	.read_press = bmp380_read_press,
 	.read_calib = bmp380_read_calib,
+	.set_mode = bmp380_set_mode,
+	.wait_conv = bmp380_wait_conv,
 	.preinit = bmp380_preinit,
 
 	.trigger_handler = bmp380_trigger_handler,

@@ -2101,6 +2267,75 @@ static int bmp580_preinit(struct bmp280_data *data)
 	return PTR_ERR_OR_ZERO(devm_nvmem_register(config.dev, &config));
 }
 
+static const u8 bmp580_operation_mode[] = {
+	BMP580_MODE_SLEEP, BMP580_MODE_FORCED, BMP580_MODE_NORMAL,
+};
+
+static int bmp580_set_mode(struct bmp280_data *data, enum bmp280_op_mode mode)
+{
+	struct device *dev = data->dev;
+	int ret;
+
+	switch (mode) {
+	case BMP280_SLEEP:
+	case BMP280_NORMAL:
+		break;
+	case BMP280_FORCED:
+		ret = regmap_set_bits(data->regmap, BMP580_REG_DSP_CONFIG,
+				      BMP580_DSP_IIR_FORCED_FLUSH);
+		if (ret) {
+			dev_err(dev, "Could not flush IIR filter constants.\n");
+			return ret;
+		}
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	ret = regmap_write_bits(data->regmap, BMP580_REG_ODR_CONFIG,
+				BMP580_MODE_MASK,
+				FIELD_PREP(BMP580_MODE_MASK,
+					   bmp580_operation_mode[mode]));
+	if (ret) {
+		dev_err(dev, "failed to  write power control register.\n");
+		return ret;
+	}
+
+	data->op_mode = mode;
+
+	return 0;
+}
+
+static int bmp580_wait_conv(struct bmp280_data *data)
+{
+	/*
+	 * Taken from datasheet, Section 2 "Specification, Table 3 "Electrical
+	 * characteristics.
+	 */
+	static const int time_conv_press[] = {
+		0, 1050, 1785, 3045, 5670, 10920, 21420, 42420,
+		84420,
+	};
+	static const int time_conv_temp[] = {
+		0, 1050, 1105, 1575, 2205, 3465, 6090, 11340,
+		21840,
+	};
+	int meas_time_us;
+
+	meas_time_us = 4 * USEC_PER_MSEC +
+		       time_conv_temp[data->oversampling_temp] +
+		       time_conv_press[data->oversampling_press];
+
+	/*
+	 * Measurement time mentioned in Chapter 2, Table 4 of the datasheet.
+	 * The extra 4ms is the required mode change to start of measurement
+	 * time.
+	 */
+	fsleep(meas_time_us);
+
+	return 0;
+}
+
 static int bmp580_chip_config(struct bmp280_data *data)
 {
 	bool change = false, aux;

@@ -2171,17 +2406,6 @@ static int bmp580_chip_config(struct bmp280_data *data)
 		return ret;
 	}
 
-	/* Restore sensor to normal operation mode */
-	ret = regmap_write_bits(data->regmap, BMP580_REG_ODR_CONFIG,
-				BMP580_MODE_MASK,
-				FIELD_PREP(BMP580_MODE_MASK, BMP580_MODE_NORMAL));
-	if (ret) {
-		dev_err(data->dev, "failed to set normal mode\n");
-		return ret;
-	}
-	/* From datasheet's table 4: electrical characteristics */
-	usleep_range(3000, 3500);
-
 	if (change) {
 		/*
 		 * Check if ODR and OSR settings are valid or we are

@@ -2279,6 +2503,8 @@ const struct bmp280_chip_info bmp580_chip_info = {
 	.chip_config = bmp580_chip_config,
 	.read_temp = bmp580_read_temp,
 	.read_press = bmp580_read_press,
+	.set_mode = bmp580_set_mode,
+	.wait_conv = bmp580_wait_conv,
 	.preinit = bmp580_preinit,
 
 	.trigger_handler = bmp580_trigger_handler,

@@ -2526,6 +2752,19 @@ static int bmp180_read_press(struct bmp280_data *data, u32 *comp_press)
 	return 0;
 }
 
+/* Keep compatibility with newer generations of the sensor */
+static int bmp180_set_mode(struct bmp280_data *data, enum bmp280_op_mode mode)
+{
+	return 0;
+}
+
+/* Keep compatibility with newer generations of the sensor */
+static int bmp180_wait_conv(struct bmp280_data *data)
+{
+	return 0;
+}
+
+/* Keep compatibility with newer generations of the sensor */
 static int bmp180_chip_config(struct bmp280_data *data)
 {
 	return 0;

@@ -2597,6 +2836,8 @@ const struct bmp280_chip_info bmp180_chip_info = {
 	.read_temp = bmp180_read_temp,
 	.read_press = bmp180_read_press,
 	.read_calib = bmp180_read_calib,
+	.set_mode = bmp180_set_mode,
+	.wait_conv = bmp180_wait_conv,
 
 	.trigger_handler = bmp180_trigger_handler,
 };

@@ -2649,6 +2890,7 @@ static int bmp280_buffer_preenable(struct iio_dev *indio_dev)
 	struct bmp280_data *data = iio_priv(indio_dev);
 
 	pm_runtime_get_sync(data->dev);
+	data->chip_info->set_mode(data, BMP280_NORMAL);
 
 	return 0;
 }

@@ -2819,6 +3061,10 @@ int bmp280_common_probe(struct device *dev,
 			return ret;
 	}
 
+	ret = data->chip_info->set_mode(data, BMP280_SLEEP);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to set sleep mode\n");
+
 	/* Enable runtime PM */
 	pm_runtime_get_noresume(dev);
 	pm_runtime_set_active(dev);

@@ -2844,6 +3090,9 @@ static int bmp280_runtime_suspend(struct device *dev)
 	struct iio_dev *indio_dev = dev_get_drvdata(dev);
 	struct bmp280_data *data = iio_priv(indio_dev);
 
+	data->chip_info->set_mode(data, BMP280_SLEEP);
+
+	fsleep(data->start_up_time);
 	return regulator_bulk_disable(BMP280_NUM_SUPPLIES, data->supplies);
 }
 

@@ -2858,7 +3107,12 @@ static int bmp280_runtime_resume(struct device *dev)
 		return ret;
 
 	usleep_range(data->start_up_time, data->start_up_time + 100);
-	return data->chip_info->chip_config(data);
+
+	ret = data->chip_info->chip_config(data);
+	if (ret)
+		return ret;
+
+	return data->chip_info->set_mode(data, data->op_mode);
 }
 
 EXPORT_RUNTIME_DEV_PM_OPS(bmp280_dev_pm_ops, bmp280_runtime_suspend,

index dc1bf04cb0b5..3babf90ce73c 100644
@@ -170,6 +170,11 @@
 #define BMP380_MODE_FORCED		1
 #define BMP380_MODE_NORMAL		3
 
+#define BMP380_MEAS_OFFSET		234
+#define BMP380_MEAS_DUR			2020
+#define BMP380_TEMP_MEAS_OFFSET		163
+#define BMP380_PRESS_MEAS_OFFSET	392
+
 #define BMP380_MIN_TEMP			-4000
 #define BMP380_MAX_TEMP			8500
 #define BMP380_MIN_PRES			3000000

@@ -206,6 +211,7 @@
 #define BMP280_REG_CTRL_MEAS		0xF4
 #define BMP280_REG_STATUS		0xF3
 #define BMP280_REG_STATUS_IM_UPDATE	BIT(0)
+#define BMP280_REG_STATUS_MEAS_BIT	BIT(3)
 #define BMP280_REG_RESET		0xE0
 #define BMP280_RST_SOFT_CMD		0xB6
 

@@ -246,6 +252,10 @@
 #define BMP280_MODE_FORCED		1
 #define BMP280_MODE_NORMAL		3
 
+#define BMP280_MEAS_OFFSET		1250
+#define BMP280_MEAS_DUR			2300
+#define BMP280_PRESS_HUMID_MEAS_OFFSET	575
+
 /* BME280 specific registers */
 #define BME280_REG_HUMIDITY_LSB		0xFE
 #define BME280_REG_HUMIDITY_MSB		0xFD

@@ -385,6 +395,12 @@ struct bmp380_calib {
 	s8  P11;
 };
 
+enum bmp280_op_mode {
+	BMP280_SLEEP,
+	BMP280_FORCED,
+	BMP280_NORMAL,
+};
+
 struct bmp280_data {
 	struct device *dev;
 	struct mutex lock;

@@ -423,6 +439,9 @@ struct bmp280_data {
 	u8 sensor_data[ALIGN(sizeof(s32) * BME280_NUM_MAX_CHANNELS, sizeof(s64))
 		       + sizeof(s64)] __aligned(sizeof(s64));
 
+	/* Value to hold the current operation mode of the device */
+	enum bmp280_op_mode op_mode;
+
 	/*
 	 * DMA (thus cache coherency maintenance) may require the
 	 * transfer buffers to live in their own cache lines.

@@ -487,6 +506,8 @@ struct bmp280_chip_info {
 	int (*read_humid)(struct bmp280_data *data, u32 *adc_humidity);
 	int (*read_calib)(struct bmp280_data *data);
 	int (*preinit)(struct bmp280_data *data);
+	int (*set_mode)(struct bmp280_data *data, enum bmp280_op_mode mode);
+	int (*wait_conv)(struct bmp280_data *data);
 
 	irqreturn_t (*trigger_handler)(int irq, void *p);
 };

index 9ad29cf4c2ac..5779e1977a7a 100644
@@ -42,12 +42,14 @@
 #include <linux/module.h>
 #include <linux/nvmem-provider.h>
 #include <linux/pm_runtime.h>
+#include <linux/property.h>
 #include <linux/random.h>
 #include <linux/regmap.h>
 #include <linux/regulator/consumer.h>
 
 #include <linux/iio/buffer.h>
 #include <linux/iio/iio.h>
+#include <linux/iio/trigger.h>
 #include <linux/iio/trigger_consumer.h>
 #include <linux/iio/triggered_buffer.h>
 

@@ -1284,6 +1286,63 @@ static irqreturn_t bme280_trigger_handler(int irq, void *p)
 	return IRQ_HANDLED;
 }
 
+static int __bmp280_trigger_probe(struct iio_dev *indio_dev,
+				  const struct iio_trigger_ops *trigger_ops,
+				  int (*int_pin_config)(struct bmp280_data *data),
+				  irq_handler_t irq_thread_handler)
+{
+	struct bmp280_data *data = iio_priv(indio_dev);
+	struct device *dev = data->dev;
+	u32 irq_type;
+	int ret, irq;
+
+	irq = fwnode_irq_get(dev_fwnode(dev), 0);
+	if (irq < 0)
+		return dev_err_probe(dev, irq, "No interrupt found.\n");
+
+	irq_type = irq_get_trigger_type(irq);
+	switch (irq_type) {
+	case IRQF_TRIGGER_RISING:
+		data->trig_active_high = true;
+		break;
+	case IRQF_TRIGGER_FALLING:
+		data->trig_active_high = false;
+		break;
+	default:
+		return dev_err_probe(dev, -EINVAL, "Invalid interrupt type specified.\n");
+	}
+
+	data->trig_open_drain =
+		fwnode_property_read_bool(dev_fwnode(dev), "int-open-drain");
+
+	ret = int_pin_config(data);
+	if (ret)
+		return ret;
+
+	data->trig = devm_iio_trigger_alloc(data->dev, "%s-dev%d",
+					    indio_dev->name,
+					    iio_device_id(indio_dev));
+	if (!data->trig)
+		return -ENOMEM;
+
+	data->trig->ops = trigger_ops;
+	iio_trigger_set_drvdata(data->trig, data);
+
+	ret = devm_request_threaded_irq(data->dev, irq, NULL,
+					irq_thread_handler, IRQF_ONESHOT,
+					indio_dev->name, indio_dev);
+	if (ret)
+		return dev_err_probe(dev, ret, "request IRQ failed.\n");
+
+	ret = devm_iio_trigger_register(data->dev, data->trig);
+	if (ret)
+		return dev_err_probe(dev, ret, "iio trigger register failed.\n");
+
+	indio_dev->trig = iio_trigger_get(data->trig);
+
+	return 0;
+}
+
 static const u8 bme280_chip_ids[] = { BME280_CHIP_ID };
 static const int bme280_humid_coeffs[] = { 1000, 1024 };
 

@@ -1785,6 +1844,81 @@ static int bmp380_chip_config(struct bmp280_data *data)
 	return ret;
 }
 
+static void bmp380_trigger_reenable(struct iio_trigger *trig)
+{
+	struct bmp280_data *data = iio_trigger_get_drvdata(trig);
+	unsigned int tmp;
+	int ret;
+
+	ret = regmap_read(data->regmap, BMP380_REG_INT_STATUS, &tmp);
+	if (ret)
+		dev_err(data->dev, "Failed to reset interrupt.\n");
+}
+
+static int bmp380_data_rdy_trigger_set_state(struct iio_trigger *trig,
+					     bool state)
+{
+	struct bmp280_data *data = iio_trigger_get_drvdata(trig);
+	int ret;
+
+	guard(mutex)(&data->lock);
+
+	ret = regmap_update_bits(data->regmap, BMP380_REG_INT_CONTROL,
+				 BMP380_INT_CTRL_DRDY_EN,
+				 FIELD_PREP(BMP380_INT_CTRL_DRDY_EN, !!state));
+	if (ret)
+		dev_err(data->dev,
+			"Could not %s interrupt.\n", str_enable_disable(state));
+	return ret;
+}
+
+static const struct iio_trigger_ops bmp380_trigger_ops = {
+	.set_trigger_state = &bmp380_data_rdy_trigger_set_state,
+	.reenable = &bmp380_trigger_reenable,
+};
+
+static int bmp380_int_pin_config(struct bmp280_data *data)
+{
+	int pin_drive_cfg = FIELD_PREP(BMP380_INT_CTRL_OPEN_DRAIN,
+				       data->trig_open_drain);
+	int pin_level_cfg = FIELD_PREP(BMP380_INT_CTRL_LEVEL,
+				       data->trig_active_high);
+	int ret, int_pin_cfg = pin_drive_cfg | pin_level_cfg;
+
+	ret = regmap_update_bits(data->regmap, BMP380_REG_INT_CONTROL,
+				 BMP380_INT_CTRL_SETTINGS_MASK, int_pin_cfg);
+	if (ret)
+		dev_err(data->dev, "Could not set interrupt settings.\n");
+
+	return ret;
+}
+
+static irqreturn_t bmp380_irq_thread_handler(int irq, void *p)
+{
+	struct iio_dev *indio_dev = p;
+	struct bmp280_data *data = iio_priv(indio_dev);
+	unsigned int int_ctrl;
+	int ret;
+
+	scoped_guard(mutex, &data->lock) {
+		ret = regmap_read(data->regmap, BMP380_REG_INT_STATUS, &int_ctrl);
+		if (ret)
+			return IRQ_NONE;
+	}
+
+	if (FIELD_GET(BMP380_INT_STATUS_DRDY, int_ctrl))
+		iio_trigger_poll_nested(data->trig);
+
+	return IRQ_HANDLED;
+}
+
+static int bmp380_trigger_probe(struct iio_dev *indio_dev)
+{
+	return __bmp280_trigger_probe(indio_dev, &bmp380_trigger_ops,
+				      bmp380_int_pin_config,
+				      bmp380_irq_thread_handler);
+}
+
 static irqreturn_t bmp380_trigger_handler(int irq, void *p)
 {
 	struct iio_poll_func *pf = p;

@@ -1882,6 +2016,7 @@ const struct bmp280_chip_info bmp380_chip_info = {
 	.wait_conv = bmp380_wait_conv,
 	.preinit = bmp380_preinit,
 
+	.trigger_probe = bmp380_trigger_probe,
 	.trigger_handler = bmp380_trigger_handler,
 };
 EXPORT_SYMBOL_NS(bmp380_chip_info, IIO_BMP280);

@@ -2429,6 +2564,88 @@ static int bmp580_chip_config(struct bmp280_data *data)
 	return 0;
 }
 
+static void bmp580_trigger_reenable(struct iio_trigger *trig)
+{
+	struct bmp280_data *data = iio_trigger_get_drvdata(trig);
+	unsigned int tmp;
+	int ret;
+
+	ret = regmap_read(data->regmap, BMP580_REG_INT_STATUS, &tmp);
+	if (ret)
+		dev_err(data->dev, "Failed to reset interrupt.\n");
+}
+
+static int bmp580_data_rdy_trigger_set_state(struct iio_trigger *trig,
+					     bool state)
+{
+	struct bmp280_data *data = iio_trigger_get_drvdata(trig);
+	int ret;
+
+	guard(mutex)(&data->lock);
+
+	ret = regmap_update_bits(data->regmap, BMP580_REG_INT_CONFIG,
+				 BMP580_INT_CONFIG_INT_EN,
+				 FIELD_PREP(BMP580_INT_CONFIG_INT_EN, !!state));
+	if (ret)
+		dev_err(data->dev,
+			"Could not %s interrupt.\n", str_enable_disable(state));
+	return ret;
+}
+
+static const struct iio_trigger_ops bmp580_trigger_ops = {
+	.set_trigger_state = &bmp580_data_rdy_trigger_set_state,
+	.reenable = &bmp580_trigger_reenable,
+};
+
+static int bmp580_int_pin_config(struct bmp280_data *data)
+{
+	int pin_drive_cfg = FIELD_PREP(BMP580_INT_CONFIG_OPEN_DRAIN,
+				       data->trig_open_drain);
+	int pin_level_cfg = FIELD_PREP(BMP580_INT_CONFIG_LEVEL,
+				       data->trig_active_high);
+	int ret, int_pin_cfg = pin_drive_cfg | pin_level_cfg;
+
+	ret = regmap_update_bits(data->regmap, BMP580_REG_INT_CONFIG,
+				 BMP580_INT_CONFIG_MASK, int_pin_cfg);
+	if (ret) {
+		dev_err(data->dev, "Could not set interrupt settings.\n");
+		return ret;
+	}
+
+	ret = regmap_set_bits(data->regmap, BMP580_REG_INT_SOURCE,
+			      BMP580_INT_SOURCE_DRDY);
+	if (ret)
+		dev_err(data->dev, "Could not set interrupt source.\n");
+
+	return ret;
+}
+
+static irqreturn_t bmp580_irq_thread_handler(int irq, void *p)
+{
+	struct iio_dev *indio_dev = p;
+	struct bmp280_data *data = iio_priv(indio_dev);
+	unsigned int int_ctrl;
+	int ret;
+
+	scoped_guard(mutex, &data->lock) {
+		ret = regmap_read(data->regmap, BMP580_REG_INT_STATUS, &int_ctrl);
+		if (ret)
+			return IRQ_NONE;
+	}
+
+	if (FIELD_GET(BMP580_INT_STATUS_DRDY_MASK, int_ctrl))
+		iio_trigger_poll_nested(data->trig);
+
+	return IRQ_HANDLED;
+}
+
+static int bmp580_trigger_probe(struct iio_dev *indio_dev)
+{
+	return __bmp280_trigger_probe(indio_dev, &bmp580_trigger_ops,
+				      bmp580_int_pin_config,
+				      bmp580_irq_thread_handler);
+}
+
 static irqreturn_t bmp580_trigger_handler(int irq, void *p)
 {
 	struct iio_poll_func *pf = p;

@@ -2507,6 +2724,7 @@ const struct bmp280_chip_info bmp580_chip_info = {
 	.wait_conv = bmp580_wait_conv,
 	.preinit = bmp580_preinit,
 
+	.trigger_probe = bmp580_trigger_probe,
 	.trigger_handler = bmp580_trigger_handler,
 };
 EXPORT_SYMBOL_NS(bmp580_chip_info, IIO_BMP280);

@@ -3055,8 +3273,11 @@ int bmp280_common_probe(struct device *dev,
 	 * however as it happens, the BMP085 shares the chip ID of BMP180
 	 * so we look for an IRQ if we have that.
 	 */
-	if (irq > 0 && (chip_id  == BMP180_CHIP_ID)) {
-		ret = bmp085_fetch_eoc_irq(dev, name, irq, data);
+	if (irq > 0) {
+		if (chip_id == BMP180_CHIP_ID)
+			ret = bmp085_fetch_eoc_irq(dev, name, irq, data);
+		if (data->chip_info->trigger_probe)
+			ret = data->chip_info->trigger_probe(indio_dev);
 		if (ret)
 			return ret;
 	}

index 3babf90ce73c..12f6e90b3728 100644
@@ -55,8 +55,17 @@
 #define BMP580_CMD_NVM_WRITE_SEQ_1	0xA0
 #define BMP580_CMD_SOFT_RESET		0xB6
 
+#define BMP580_INT_STATUS_DRDY_MASK	BIT(0)
 #define BMP580_INT_STATUS_POR_MASK	BIT(4)
 
+#define BMP580_INT_SOURCE_DRDY		BIT(0)
+
+#define BMP580_INT_CONFIG_MASK		GENMASK(3, 0)
+#define BMP580_INT_CONFIG_LATCH		BIT(0)
+#define BMP580_INT_CONFIG_LEVEL		BIT(1)
+#define BMP580_INT_CONFIG_OPEN_DRAIN	BIT(2)
+#define BMP580_INT_CONFIG_INT_EN	BIT(3)
+
 #define BMP580_STATUS_CORE_RDY_MASK	BIT(0)
 #define BMP580_STATUS_NVM_RDY_MASK	BIT(1)
 #define BMP580_STATUS_NVM_ERR_MASK	BIT(2)

@@ -175,6 +184,14 @@
 #define BMP380_TEMP_MEAS_OFFSET		163
 #define BMP380_PRESS_MEAS_OFFSET	392
 
+#define BMP380_INT_STATUS_DRDY		BIT(3)
+
+#define BMP380_INT_CTRL_SETTINGS_MASK	GENMASK(2, 0)
+#define BMP380_INT_CTRL_OPEN_DRAIN	BIT(0)
+#define BMP380_INT_CTRL_LEVEL		BIT(1)
+#define BMP380_INT_CTRL_LATCH		BIT(2)
+#define BMP380_INT_CTRL_DRDY_EN		BIT(6)
+
 #define BMP380_MIN_TEMP			-4000
 #define BMP380_MAX_TEMP			8500
 #define BMP380_MIN_PRES			3000000

@@ -407,6 +424,9 @@ struct bmp280_data {
 	struct regmap *regmap;
 	struct completion done;
 	bool use_eoc;
+	bool trig_open_drain;
+	bool trig_active_high;
+	struct iio_trigger *trig;
 	const struct bmp280_chip_info *chip_info;
 	union {
 		struct bmp180_calib bmp180;

@@ -509,6 +529,7 @@ struct bmp280_chip_info {
 	int (*set_mode)(struct bmp280_data *data, enum bmp280_op_mode mode);
 	int (*wait_conv)(struct bmp280_data *data);
 
+	int (*trigger_probe)(struct iio_dev *indio_dev);
 	irqreturn_t (*trigger_handler)(int irq, void *p);
 };
 

index 5779e1977a7a..da7ae7e3164c 100644
@@ -3070,13 +3070,16 @@ static irqreturn_t bmp085_eoc_irq(int irq, void *d)
 	return IRQ_HANDLED;
 }
 
-static int bmp085_fetch_eoc_irq(struct device *dev,
-				const char *name,
-				int irq,
-				struct bmp280_data *data)
+static int bmp085_trigger_probe(struct iio_dev *indio_dev)
 {
+	struct bmp280_data *data = iio_priv(indio_dev);
+	struct device *dev = data->dev;
 	unsigned long irq_trig;
-	int ret;
+	int ret, irq;
+
+	irq = fwnode_irq_get(dev_fwnode(dev), 0);
+	if (irq < 0)
+		return dev_err_probe(dev, irq, "No interrupt found.\n");
 
 	irq_trig = irq_get_trigger_type(irq);
 	if (irq_trig != IRQF_TRIGGER_RISING) {

@@ -3086,13 +3089,8 @@ static int bmp085_fetch_eoc_irq(struct device *dev,
 
 	init_completion(&data->done);
 
-	ret = devm_request_threaded_irq(dev,
-			irq,
-			bmp085_eoc_irq,
-			NULL,
-			irq_trig,
-			name,
-			data);
+	ret = devm_request_irq(dev, irq, bmp085_eoc_irq, irq_trig,
+			       indio_dev->name, data);
 	if (ret) {
 		/* Bail out without IRQ but keep the driver in place */
 		dev_err(dev, "unable to request DRDY IRQ\n");

@@ -3100,9 +3098,48 @@ static int bmp085_fetch_eoc_irq(struct device *dev,
 	}
 
 	data->use_eoc = true;
+
 	return 0;
 }
 
+/* Identical to bmp180_chip_info + bmp085_trigger_probe */
+const struct bmp280_chip_info bmp085_chip_info = {
+	.id_reg = BMP280_REG_ID,
+	.chip_id = bmp180_chip_ids,
+	.num_chip_id = ARRAY_SIZE(bmp180_chip_ids),
+	.regmap_config = &bmp180_regmap_config,
+	.start_up_time = 2000,
+	.channels = bmp280_channels,
+	.num_channels = ARRAY_SIZE(bmp280_channels),
+	.avail_scan_masks = bmp280_avail_scan_masks,
+
+	.oversampling_temp_avail = bmp180_oversampling_temp_avail,
+	.num_oversampling_temp_avail =
+		ARRAY_SIZE(bmp180_oversampling_temp_avail),
+	.oversampling_temp_default = 0,
+
+	.oversampling_press_avail = bmp180_oversampling_press_avail,
+	.num_oversampling_press_avail =
+		ARRAY_SIZE(bmp180_oversampling_press_avail),
+	.oversampling_press_default = BMP180_MEAS_PRESS_8X,
+
+	.temp_coeffs = bmp180_temp_coeffs,
+	.temp_coeffs_type = IIO_VAL_FRACTIONAL,
+	.press_coeffs = bmp180_press_coeffs,
+	.press_coeffs_type = IIO_VAL_FRACTIONAL,
+
+	.chip_config = bmp180_chip_config,
+	.read_temp = bmp180_read_temp,
+	.read_press = bmp180_read_press,
+	.read_calib = bmp180_read_calib,
+	.set_mode = bmp180_set_mode,
+	.wait_conv = bmp180_wait_conv,
+
+	.trigger_probe = bmp085_trigger_probe,
+	.trigger_handler = bmp180_trigger_handler,
+};
+EXPORT_SYMBOL_NS(bmp085_chip_info, IIO_BMP280);
+
 static int bmp280_buffer_preenable(struct iio_dev *indio_dev)
 {
 	struct bmp280_data *data = iio_priv(indio_dev);

@@ -3274,8 +3311,6 @@ int bmp280_common_probe(struct device *dev,
 	 * so we look for an IRQ if we have that.
 	 */
 	if (irq > 0) {
-		if (chip_id == BMP180_CHIP_ID)
-			ret = bmp085_fetch_eoc_irq(dev, name, irq, data);
 		if (data->chip_info->trigger_probe)
 			ret = data->chip_info->trigger_probe(indio_dev);
 		if (ret)

index 5c3a63b4327c..2f7b25984c7b 100644
@@ -27,7 +27,7 @@ static int bmp280_i2c_probe(struct i2c_client *client)
 }
 
 static const struct of_device_id bmp280_of_i2c_match[] = {
-	{ .compatible = "bosch,bmp085", .data = &bmp180_chip_info },
+	{ .compatible = "bosch,bmp085", .data = &bmp085_chip_info },
 	{ .compatible = "bosch,bmp180", .data = &bmp180_chip_info },
 	{ .compatible = "bosch,bmp280", .data = &bmp280_chip_info },
 	{ .compatible = "bosch,bme280", .data = &bme280_chip_info },

@@ -38,7 +38,7 @@ static const struct of_device_id bmp280_of_i2c_match[] = {
 MODULE_DEVICE_TABLE(of, bmp280_of_i2c_match);
 
 static const struct i2c_device_id bmp280_i2c_id[] = {
-	{"bmp085", (kernel_ulong_t)&bmp180_chip_info },
+	{"bmp085", (kernel_ulong_t)&bmp085_chip_info },
 	{"bmp180", (kernel_ulong_t)&bmp180_chip_info },
 	{"bmp280", (kernel_ulong_t)&bmp280_chip_info },
 	{"bme280", (kernel_ulong_t)&bme280_chip_info },

index d18549d9bb64..49aa8c2cd85b 100644
@@ -114,7 +114,7 @@ static int bmp280_spi_probe(struct spi_device *spi)
 }
 
 static const struct of_device_id bmp280_of_spi_match[] = {
-	{ .compatible = "bosch,bmp085", .data = &bmp180_chip_info },
+	{ .compatible = "bosch,bmp085", .data = &bmp085_chip_info },
 	{ .compatible = "bosch,bmp180", .data = &bmp180_chip_info },
 	{ .compatible = "bosch,bmp181", .data = &bmp180_chip_info },
 	{ .compatible = "bosch,bmp280", .data = &bmp280_chip_info },

@@ -126,7 +126,7 @@ static const struct of_device_id bmp280_of_spi_match[] = {
 MODULE_DEVICE_TABLE(of, bmp280_of_spi_match);
 
 static const struct spi_device_id bmp280_spi_id[] = {
-	{ "bmp085", (kernel_ulong_t)&bmp180_chip_info },
+	{ "bmp085", (kernel_ulong_t)&bmp085_chip_info },
 	{ "bmp180", (kernel_ulong_t)&bmp180_chip_info },
 	{ "bmp181", (kernel_ulong_t)&bmp180_chip_info },
 	{ "bmp280", (kernel_ulong_t)&bmp280_chip_info },

index 12f6e90b3728..2df1175b6b85 100644
@@ -534,6 +534,7 @@ struct bmp280_chip_info {
 };
 
 /* Chip infos for each variant */
+extern const struct bmp280_chip_info bmp085_chip_info;
 extern const struct bmp280_chip_info bmp180_chip_info;
 extern const struct bmp280_chip_info bmp280_chip_info;
 extern const struct bmp280_chip_info bme280_chip_info;