Add support for Ariaboard Photonicat RK3568
Subsystems (2)
v5 cover Add support for Ariaboard Photonicat RK3568
Add dts for Ariaboard Photonicat RK3568.
This series bring support for:
* Debug UART
* SDIO QCA9377 WiFi and Bluetooth
* M.2 E-Key PCIe WiFi and Bluetooth
* M.2 B-Key USB Modem WWAN
* Ethernet WAN Port
* MicroSD Card slot
* eMMC
* HDMI Output
* Mali GPU
* USB Type-A
Changed from v1:
- move some general nodes (firmware, ramoops, reboot-mode) to rk356x.dtsi
- gmac1 change to phy-mode rgmii-id
- corrected some regulator to be closer to schematics
- rename rk3568-ariaboard-photonicat.dts to rk3568-photonicat.dts
https://lore.kernel.org/lkml/[email protected]/
Changed from v2:
- remove unused headers
- corrected some regulator to be closer to schematics
- remove usb_host1_ohci, usb_host1_ehci, usb2phy1_host that have no connection
https://lore.kernel.org/lkml/[email protected]/
Changed from v3:
- corrected some regulator to be closer to schematics
- changed to using clk32k_out1 in xin32k
https://lore.kernel.org/lkml/[email protected]/
Changed from v4:
- corrected some regulator to be closer to schematics
- corrected some label to match node name
- use resets props in phy node instead deprecated snps,reset-gpio
https://lore.kernel.org/lkml/[email protected]/
Junhao Xie (3):
dt-bindings: vendor-prefixes: Add prefix for Ariaboard
dt-bindings: arm: rockchip: Add Ariaboard Photonicat RK3568
arm64: dts: rockchip: add dts for Ariaboard Photonicat RK3568
.../devicetree/bindings/arm/rockchip.yaml | 5 + .../devicetree/bindings/vendor-prefixes.yaml | 2 + arch/arm64/boot/dts/rockchip/Makefile | 1 + .../boot/dts/rockchip/rk3568-photonicat.dts | 600 ++++++++++++++++++ 4 files changed, 608 insertions(+) create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts
Signature · 7 lines
2.47.0 _______________________________________________ Linux-rockchip mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-rockchip
PATCH v5 1/3 dt-bindings: vendor-prefixes: Add prefix for Ariaboard
Add an entry for Ariaboard from Shanghai Novotech
Ariaboard represents a product line from Shanghai Novotech Co., Ltd.
--- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/vendor-prefixes.yaml +2 -0
@@ -145,6 +145,8 @@ patternProperties: description: Arctic Sand "^arcx,.*": description: arcx Inc. / Archronix Inc. + "^ariaboard,.*": + description: Shanghai Novotech Co., Ltd. (Ariaboard) "^aries,.*": description: Aries Embedded GmbH "^arm,.*":
Signature · 1 line
2.47.0
PATCH v5 2/3 dt-bindings: arm: rockchip: Add Ariaboard Photonicat RK3568
In reply to Junhao XieThis documents Ariaboard Photonicat which is a router based on RK3568 SoC.
--- Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++ 1 file changed, 5 insertions(+)
Documentation/devicetree/bindings/arm/rockchip.yaml +5 -0
@@ -49,6 +49,11 @@ properties: - anbernic,rg-arc-s - const: rockchip,rk3566 + - description: Ariaboard Photonicat + items: + - const: ariaboard,photonicat + - const: rockchip,rk3568 + - description: ArmSoM Sige7 board items: - const: armsom,sige7
Signature · 7 lines
2.47.0 _______________________________________________ Linux-rockchip mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-rockchip
PATCH v5 3/3 arm64: dts: rockchip: add dts for Ariaboard Photonicat RK3568
In reply to Junhao XieAdd dts for Ariaboard Photonicat RK3568.
Working IO:
Debug UART
SDIO QCA9377 WiFi and Bluetooth
M.2 E-Key PCIe WiFi and Bluetooth
M.2 B-Key USB Modem WWAN
Ethernet WAN Port
MicroSD Card slot
eMMC
HDMI Output
Mali GPU
USB Type-A
Not working IO:
Ethernet LAN Port (Lack of SGMII support) Power management MCU on UART4 (Driver pending)
Not working IO in MCU:
Battery voltage sensor
Board temperature sensor
Hardware Power-off
Hardware Watchdog
Network status LED
Real-time clock
USB Charger voltage sensor
About onboard power management MCU:
A heartbeat must be sent to the MCU within 60 seconds, otherwise the MCU will restart the system.
When powering off, a shutdown command needs to be sent to the MCU. When the power button is long pressed, the MCU will send a shutdown command to the system. If system does not shutdown within 60 seconds, the power will be turned off directly.
MCU only provides voltage for charger and battery. Manufacturer removed RK8xx PMIC.
--- arch/arm64/boot/dts/rockchip/Makefile | 1 + .../boot/dts/rockchip/rk3568-photonicat.dts | 600 ++++++++++++++++++ 2 files changed, 601 insertions(+) create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts
arch/arm64/boot/dts/rockchip/Makefile +1 -0
@@ -116,6 +116,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-mecsbc.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-nanopi-r5c.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-nanopi-r5s.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-odroid-m1.dtb +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-photonicat.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-qnap-ts433.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-radxa-e25.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-roc-pc.dtb
arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts new file +600 -0
600 lines not on this page · raw message
Signature · 1 line
2.47.0
Rob Herring (Arm)
maintainerQuoted 50 lines · Junhao Xie
Add dts for Ariaboard Photonicat RK3568.
This series bring support for:
* Debug UART
* SDIO QCA9377 WiFi and Bluetooth
* M.2 E-Key PCIe WiFi and Bluetooth
* M.2 B-Key USB Modem WWAN
* Ethernet WAN Port
* MicroSD Card slot
* eMMC
* HDMI Output
* Mali GPU
* USB Type-AChanged from v1:
- move some general nodes (firmware, ramoops, reboot-mode) tork356x.dtsi
- gmac1 change to phy-mode rgmii-id
- corrected some regulator to be closer to schematics
- renamerk3568-ariaboard-photonicat.dtstork3568-photonicat.dts
https://lore.kernel.org/lkml/[email protected]/Changed from v2:
- remove unused headers
- corrected some regulator to be closer to schematics
- removeusb_host1_ohci,usb_host1_ehci,usb2phy1_hostthat have no connection
https://lore.kernel.org/lkml/[email protected]/Changed from v3:
- corrected some regulator to be closer to schematics
- changed to usingclk32k_out1in xin32k
https://lore.kernel.org/lkml/[email protected]/Changed from v4:
- corrected some regulator to be closer to schematics
- corrected some label to match node name
- use resets props in phy node instead deprecated snps,reset-gpio
https://lore.kernel.org/lkml/[email protected]/Junhao Xie (3):
dt-bindings: vendor-prefixes: Add prefix for Ariaboard
dt-bindings: arm: rockchip: Add Ariaboard Photonicat RK3568
arm64: dts: rockchip: add dts for Ariaboard Photonicat RK3568.../devicetree/bindings/arm/rockchip.yaml | 5 + .../devicetree/bindings/vendor-prefixes.yaml | 2 + arch/arm64/boot/dts/rockchip/Makefile | 1 + .../boot/dts/rockchip/rk3568-photonicat.dts | 600 ++++++++++++++++++ 4 files changed, 608 insertions(+) create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-photonicat.dts
Quoted 5 lines
--
2.47.0
My bot found new DTB warnings on the .dts files added or changed in this series.
Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings are fixed by another series. Ultimately, it is up to the platform maintainer whether these warnings are acceptable or not. No need to reply unless the platform maintainer has comments.
If you already ran DT checks and didn't see these error(s), then make sure dt-schema is up to date:
pip3 install dtschema --upgrade
New warnings running 'make CHECK_DTBS=y rockchip/rk3568-photonicat.dtb' for [email protected]:
arch/arm64/boot/dts/rockchip/rk3568-photonicat.dtb: bluetooth: 'clock-names' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/net/bluetooth/qualcomm-bluetooth.yaml#arch/arm64/boot/dts/rockchip/rk3568-photonicat.dtb: phy@fe8c0000: 'phy-supply' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/phy/rockchip,pcie3-phy.yaml#arch/arm64/boot/dts/rockchip/rk3568-photonicat.dtb: rfkill-modem: 'reset-gpios' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/net/rfkill-gpio.yaml#