Inline ECC Series
Subsystems (2)
v6 cover Inline ECC Series
Hello,
This series adds support for Inline ECC in DDR for AM64X, AM62X, AM62AX, AM62PX, J721E, J721S2, J722S and J784S4 devices.
(1/9) Add ss_cfg reg entry
(2/9) Enable ECC priming with BIST engine
(3/9) Add a function to store base address and size of RAM's banks
in a 64-bit device private data
(4/9) Setup the ECC region start and range
(5/9) Enable ECC 1-bit error, 2-bit error and multiple-bit
error interrupts
(6/9) Add CONFIG_K3_INLINE_ECC
(7/9) Remove 'ti,ecc-enable' flag
(8/9) Set default NR_DRAM_BANKS to 2
(9/9) Pull Redundant DDR functions to a common location and Fixup
DDR size when ECC is enabled
Test Results: https://gist.github.com/santhosh21/88de920771ed2efa0463a5a367cb8d7b
Changes since v5:
Add support for J722S EVM
v5: https://lore.kernel.org/u-boot/[email protected]/
Changes since v4:
1. Make dram_init and dram_init_banksize weak at mach-k3/ and define at board/ti/
2. Remove 'ti,ecc-enable' flag
3. Minor changes like patch order change (8/8 in v4 to 1/9 in v5), use 'u64'
v4: https://lore.kernel.org/u-boot/[email protected]/
Changes since v3:
Pull redundant DDR functions to arch/arm/mach-k3/*
v3: https://lore.kernel.org/all/[email protected]/
Changes since v2:
Removed 'default n' in Kconfig as that is default setting
v2: https://lore.kernel.org/u-boot/[email protected]/
Changes since v1:
Add support for J7* devices.
v1: https://lore.kernel.org/u-boot/[email protected]/
Georgi Vlaev (1):
ram: k3-ddrss: Use the DDR controller BIST engine for ECC priming
Neha Malcom Francis (2):
drivers: ram: Kconfig: Add CONFIG_K3_INLINE_ECC
arm: mach-k3: Set NR_DRAM_BANKS to 2
Santhosh Kumar K (6):
arm: dts: k3-*-ddr: Add ss_cfg reg entry
ram: k3-ddrss: Add k3_ddrss_ddr_bank_base_size_calc() to solve
'calculations restricted to 32 bits' issue
ram: k3-ddrss: Setup ECC region start and range
ram: k3-ddrss: Enable ECC interrupts
ram: k3-ddrss: Remove 'ti,ecc-enable' support
board: ti: Pull redundant DDR functions to a common location and Fixup
DDR size when ECC is enabled
arch/arm/dts/k3-am62a-ddr.dtsi | 7 +- arch/arm/dts/k3-j721s2-ddr.dtsi | 12 +- arch/arm/dts/k3-j784s4-ddr.dtsi | 24 ++- arch/arm/mach-k3/Kconfig | 3 + arch/arm/mach-k3/Makefile | 2 +- arch/arm/mach-k3/include/mach/k3-ddr.h | 15 ++ arch/arm/mach-k3/k3-ddr.c | 72 ++++++++ board/ti/am62ax/evm.c | 17 +- board/ti/am62px/evm.c | 17 +- board/ti/am62x/evm.c | 63 +------ board/ti/am64x/evm.c | 73 +-------- board/ti/am65x/evm.c | 29 +--- board/ti/common/Makefile | 1 + board/ti/common/k3-ddr.c | 33 ++++ board/ti/common/k3-ddr.h | 12 ++ board/ti/j721e/evm.c | 29 +--- board/ti/j721s2/evm.c | 35 ++-- board/ti/j722s/evm.c | 17 +- board/ti/j784s4/evm.c | 17 +- configs/am62ax_evm_a53_defconfig | 1 - configs/am62px_evm_a53_defconfig | 1 - configs/am62x_evm_a53_defconfig | 1 - configs/am62x_evm_r5_defconfig | 1 - configs/am64x_evm_a53_defconfig | 1 - configs/am64x_evm_r5_defconfig | 1 - configs/am65x_evm_a53_defconfig | 1 - configs/am65x_evm_r5_defconfig | 1 - configs/am65x_evm_r5_usbdfu_defconfig | 1 - configs/am65x_evm_r5_usbmsc_defconfig | 1 - configs/j7200_evm_a72_defconfig | 1 - configs/j721e_evm_a72_defconfig | 1 - configs/j721s2_evm_a72_defconfig | 1 - configs/j722s_evm_a53_defconfig | 1 - configs/j784s4_evm_a72_defconfig | 1 - drivers/ram/Kconfig | 10 ++ drivers/ram/k3-ddrss/k3-ddrss.c | 219 +++++++++++++++++++++---- 36 files changed, 427 insertions(+), 295 deletions(-) create mode 100644 arch/arm/mach-k3/include/mach/k3-ddr.h create mode 100644 arch/arm/mach-k3/k3-ddr.c create mode 100644 board/ti/common/k3-ddr.c create mode 100644 board/ti/common/k3-ddr.h
Signature · 1 line
2.34.1
PATCH v6 1/9 arm: dts: k3-*-ddr: Add ss_cfg reg entry
Add ss_cfg memory region which maps the DDRSS configuration region for the memory controller node.
--- arch/arm/dts/k3-am62a-ddr.dtsi | 7 ++++--- arch/arm/dts/k3-j721s2-ddr.dtsi | 12 ++++++++---- arch/arm/dts/k3-j784s4-ddr.dtsi | 24 ++++++++++++++++-------- 3 files changed, 28 insertions(+), 15 deletions(-)
arch/arm/dts/k3-am62a-ddr.dtsi +4 -3
@@ -4,11 +4,12 @@ */ / { - memorycontroller: memory-controller@f308000 { + memorycontroller: memory-controller@f300000 { compatible = "ti,am62a-ddrss"; reg = <0x00 0x0f308000 0x00 0x4000>, - <0x00 0x43014000 0x00 0x100>; - reg-names = "cfg", "ctrl_mmr_lp4"; + <0x00 0x43014000 0x00 0x100>, + <0x00 0x0f300000 0x00 0x200>; + reg-names = "cfg", "ctrl_mmr_lp4", "ss_cfg"; ti,ddr-freq1 = <DDRSS_PLL_FREQUENCY_1>; ti,ddr-freq2 = <DDRSS_PLL_FREQUENCY_2>; ti,ddr-fhs-cnt = <DDRSS_PLL_FHS_CNT>;
arch/arm/dts/k3-j721s2-ddr.dtsi +8 -4
@@ -5,6 +5,8 @@ &main_navss { ranges = <0x00 0x00114000 0x00 0x00114000 0x00 0x00000100>, // ctrl_mmr_lpr + <0x00 0x02980000 0x00 0x02980000 0x00 0x00000200>, // ss cfg 0 + <0x00 0x029a0000 0x00 0x029a0000 0x00 0x00000200>, // ss cfg 1 <0x00 0x02990000 0x00 0x02990000 0x00 0x00004000>, // ddr0 cfg <0x00 0x029b0000 0x00 0x029b0000 0x00 0x00004000>, // ddr1 cfg <0x00 0x30000000 0x00 0x30000000 0x00 0x0c400000>;
@@ -24,8 +26,9 @@ memorycontroller0: memorycontroller@2990000 { compatible = "ti,j721s2-ddrss"; reg = <0x0 0x02990000 0x0 0x4000>, - <0x0 0x0114000 0x0 0x100>; - reg-names = "cfg", "ctrl_mmr_lp4"; + <0x0 0x0114000 0x0 0x100>, + <0x0 0x02980000 0x0 0x200>; + reg-names = "cfg", "ctrl_mmr_lp4", "ss_cfg"; power-domains = <&k3_pds 138 TI_SCI_PD_SHARED>, <&k3_pds 96 TI_SCI_PD_SHARED>; clocks = <&k3_clks 138 0>, <&k3_clks 43 2>;
@@ -2232,8 +2235,9 @@ memorycontroller1: memorycontroller@29b0000 { compatible = "ti,j721s2-ddrss"; reg = <0x0 0x029b0000 0x0 0x4000>, - <0x0 0x0114000 0x0 0x100>; - reg-names = "cfg", "ctrl_mmr_lp4"; + <0x0 0x0114000 0x0 0x100>, + <0x0 0x029a0000 0x0 0x200>; + reg-names = "cfg", "ctrl_mmr_lp4", "ss_cfg"; power-domains = <&k3_pds 139 TI_SCI_PD_SHARED>, <&k3_pds 97 TI_SCI_PD_SHARED>; clocks = <&k3_clks 139 0>, <&k3_clks 43 2>;
arch/arm/dts/k3-j784s4-ddr.dtsi +16 -8
@@ -9,6 +9,10 @@ <0x00 0x029b0000 0x00 0x029b0000 0x00 0x00004000>, // ddr1 cfg <0x00 0x029d0000 0x00 0x029d0000 0x00 0x00004000>, // ddr2 cfg <0x00 0x029f0000 0x00 0x029f0000 0x00 0x00004000>, // ddr3 cfg + <0x00 0x02980000 0x00 0x02980000 0x00 0x00000200>, // ss cfg 0 + <0x00 0x029a0000 0x00 0x029a0000 0x00 0x00000200>, // ss cfg 1 + <0x00 0x029c0000 0x00 0x029c0000 0x00 0x00000200>, // ss cfg 2 + <0x00 0x029e0000 0x00 0x029e0000 0x00 0x00000200>, // ss cfg 3 <0x00 0x30000000 0x00 0x30000000 0x00 0x0c400000>; msmc0: msmc {
@@ -26,8 +30,9 @@ memorycontroller0: memorycontroller@2990000 { compatible = "ti,j721s2-ddrss"; reg = <0x0 0x02990000 0x0 0x4000>, - <0x0 0x0114000 0x0 0x100>; - reg-names = "cfg", "ctrl_mmr_lp4"; + <0x0 0x0114000 0x0 0x100>, + <0x0 0x02980000 0x0 0x200>; + reg-names = "cfg", "ctrl_mmr_lp4", "ss_cfg"; power-domains = <&k3_pds 191 TI_SCI_PD_SHARED>, <&k3_pds 131 TI_SCI_PD_SHARED>; clocks = <&k3_clks 191 1>, <&k3_clks 78 2>;
@@ -2234,8 +2239,9 @@ memorycontroller1: memorycontroller@29b0000 { compatible = "ti,j721s2-ddrss"; reg = <0x0 0x029b0000 0x0 0x4000>, - <0x0 0x0114000 0x0 0x100>; - reg-names = "cfg", "ctrl_mmr_lp4"; + <0x0 0x0114000 0x0 0x100>, + <0x0 0x029a0000 0x0 0x200>; + reg-names = "cfg", "ctrl_mmr_lp4", "ss_cfg"; power-domains = <&k3_pds 192 TI_SCI_PD_SHARED>, <&k3_pds 132 TI_SCI_PD_SHARED>; clocks = <&k3_clks 192 1>, <&k3_clks 78 2>;
@@ -4442,8 +4448,9 @@ memorycontroller2: memorycontroller@29d0000 { compatible = "ti,j721s2-ddrss"; reg = <0x0 0x029d0000 0x0 0x4000>, - <0x0 0x0114000 0x0 0x100>; - reg-names = "cfg", "ctrl_mmr_lp4"; + <0x0 0x0114000 0x0 0x100>, + <0x0 0x029c0000 0x0 0x200>; + reg-names = "cfg", "ctrl_mmr_lp4", "ss_cfg"; power-domains = <&k3_pds 193 TI_SCI_PD_SHARED>, <&k3_pds 133 TI_SCI_PD_SHARED>; clocks = <&k3_clks 193 1>, <&k3_clks 78 2>;
@@ -6650,8 +6657,9 @@ memorycontroller3: memorycontroller@29f0000 { compatible = "ti,j721s2-ddrss"; reg = <0x0 0x029f0000 0x0 0x4000>, - <0x0 0x0114000 0x0 0x100>; - reg-names = "cfg", "ctrl_mmr_lp4"; + <0x0 0x0114000 0x0 0x100>, + <0x0 0x29e0000 0x0 0x200>; + reg-names = "cfg", "ctrl_mmr_lp4", "ss_cfg"; power-domains = <&k3_pds 194 TI_SCI_PD_SHARED>, <&k3_pds 139 TI_SCI_PD_SHARED>; clocks = <&k3_clks 194 1>, <&k3_clks 78 2>;
Signature · 1 line
2.34.1
PATCH v6 2/9 ram: k3-ddrss: Use the DDR controller BIST engine for ECC priming
In reply to Santhosh Kumar KFrom: Georgi Vlaev <[email protected]>
The 1-bit inline ECC support in TI's DDRSS bridge requires the configured memory regions to be preloaded with a pattern before use. This is done by the k3-ddrss driver from the R5 SPL in a 'for' loop. It takes around 10 seconds to fill 2GB of memory, for example. Memset can cut the time in half and using DMA currently yields a similar result.
The BIST engine of DDR controller provides support for initializing any memory region with a pattern. This bypasses the DDRSS bridge, so the required inline ECC data is not computed and populated in the memory. For some values like zero, the computed ECC syndrome is also zero and we can use these values to preload the memory from the DDR controller, without the assistance of the bridge.
The registers involved in the process are described in the 'DDR controller registers' topic in [1] AM62 and [2] J721E reference manuals.
The patch replaces the 'for' loop memory fill function with the BIST memory initialization procedure. This cuts the time to preload the 2GB memory from 10 seconds down to 1 second. The bist preload function uses the lpddr4 APIs in the k3-ddrss, so this is compatible with devices with both 16-bit LPDDR4 and 32-bit LPDDR4 interfaces (e.g J721E).
[1] AM62x: https://www.ti.com/lit/pdf/spruiv7
[2] DRA829/TDA4VM: https://www.ti.com/lit/zip/spruil1
--- drivers/ram/k3-ddrss/k3-ddrss.c | 122 +++++++++++++++++++++++++++++--- 1 file changed, 114 insertions(+), 8 deletions(-)
drivers/ram/k3-ddrss/k3-ddrss.c +114 -8
@@ -6,6 +6,7 @@*/ #include <config.h> +#include <time.h> #include <clk.h> #include <div64.h> #include <dm.h>
@@ -548,14 +549,118 @@ static void k3_ddrss_set_ecc_range_r0(u32 base, u32 start_address, u32 size)writel ((start_address + size -1 ) >>16 , base +DDRSS_ECC_R0_END_ADDR_REG ); } -static void k3_ddrss_preload_ecc_mem_region (u32 *addr,u32 size,u32 word) +#define BIST_MODE_MEM_INIT 4 +#define BIST_MEM_INIT_TIMEOUT 10000/* 1msec loops per block = 10s */ +static void k3_lpddr4_bist_init_mem_region (struct k3_ddrss_desc *ddrss, +u64 addr,u64 size, +u32 pattern) { -int i; +lpddr4_obj *driverdt = ddrss->driverdt; +lpddr4_privatedata *pd = &ddrss->pd; +u32 status, offset, regval; +bool int_status; +int i =0 ; + +/* Set BIST_START_ADDR_0 [31:0] */ + regval = (u32)(addr &TH_FLD_MASK (LPDDR4__BIST_START_ADDRESS_0__FLD )); +TH_OFFSET_FROM_REG (LPDDR4__BIST_START_ADDRESS_0__REG ,CTL_SHIFT , offset); + driverdt->writereg (pd,LPDDR4_CTL_REGS , offset, regval); + +/* Set BIST_START_ADDR_1 [32 or 34:32] */ + regval = (u32)(addr >>TH_FLD_WIDTH (LPDDR4__BIST_START_ADDRESS_0__FLD )); + regval &=TH_FLD_MASK (LPDDR4__BIST_START_ADDRESS_1__FLD ); +TH_OFFSET_FROM_REG (LPDDR4__BIST_START_ADDRESS_1__REG ,CTL_SHIFT , offset); + driverdt->writereg (pd,LPDDR4_CTL_REGS , offset, regval); + +/* Set ADDR_SPACE = log2(size) */ + regval = (u32)(ilog2 (size) <<TH_FLD_SHIFT (LPDDR4__ADDR_SPACE__FLD )); +TH_OFFSET_FROM_REG (LPDDR4__ADDR_SPACE__REG ,CTL_SHIFT , offset); + driverdt->writereg (pd,LPDDR4_CTL_REGS , offset, regval); + +/* Enable the BIST data check. On 32bit lpddr4 (e.g J7) this shares a +* register with ADDR_SPACE and BIST_GO. +*/ +TH_OFFSET_FROM_REG (LPDDR4__BIST_DATA_CHECK__REG ,CTL_SHIFT , offset); + driverdt->readreg (pd,LPDDR4_CTL_REGS , offset, ®val); + regval |=TH_FLD_MASK (LPDDR4__BIST_DATA_CHECK__FLD ); + driverdt->writereg (pd,LPDDR4_CTL_REGS , offset, regval); +/* Clear the address check bit */ +TH_OFFSET_FROM_REG (LPDDR4__BIST_ADDR_CHECK__REG ,CTL_SHIFT , offset); + driverdt->readreg (pd,LPDDR4_CTL_REGS , offset, ®val); + regval &= ~TH_FLD_MASK (LPDDR4__BIST_ADDR_CHECK__FLD ); + driverdt->writereg (pd,LPDDR4_CTL_REGS , offset, regval); + +/* Set BIST_TEST_MODE[2:0] to memory initialize (4) */ + regval =BIST_MODE_MEM_INIT ; +TH_OFFSET_FROM_REG (LPDDR4__BIST_TEST_MODE__REG ,CTL_SHIFT , offset); + driverdt->writereg (pd,LPDDR4_CTL_REGS , offset, regval); + +/* Set BIST_DATA_PATTERN[31:0] */ +TH_OFFSET_FROM_REG (LPDDR4__BIST_DATA_PATTERN_0__REG ,CTL_SHIFT , offset); + driverdt->writereg (pd,LPDDR4_CTL_REGS , offset, pattern); + +/* Set BIST_DATA_PATTERN[63:32] */ +TH_OFFSET_FROM_REG (LPDDR4__BIST_DATA_PATTERN_1__REG ,CTL_SHIFT , offset); + driverdt->writereg (pd,LPDDR4_CTL_REGS , offset, pattern); + +udelay (1000 ); + +/* Enable the programmed BIST operation - BIST_GO = 1 */ +TH_OFFSET_FROM_REG (LPDDR4__BIST_GO__REG ,CTL_SHIFT , offset); + driverdt->readreg (pd,LPDDR4_CTL_REGS , offset, ®val); + regval |=TH_FLD_MASK (LPDDR4__BIST_GO__FLD ); + driverdt->writereg (pd,LPDDR4_CTL_REGS , offset, regval); + +/* Wait for the BIST_DONE interrupt */ +while (i <BIST_MEM_INIT_TIMEOUT ) { + status = driverdt->checkctlinterrupt (pd,LPDDR4_INTR_BIST_DONE , + &int_status); +if (!status & int_status) { +/* Clear LPDDR4_INTR_BIST_DONE */ + driverdt->ackctlinterrupt (pd,LPDDR4_INTR_BIST_DONE ); +break ; + } +udelay (1000 ); + i++; + } -printf ("ECC is enabled, priming DDR which will take several seconds.\n" ); +/* Before continuing we have to stop BIST - BIST_GO = 0 */ +TH_OFFSET_FROM_REG (LPDDR4__BIST_GO__REG ,CTL_SHIFT , offset); + driverdt->writereg (pd,LPDDR4_CTL_REGS , offset,0 ); + +/* Timeout hit while priming the memory. We can't continue, +* since the memory is not fully initialized and we most +* likely get an uncorrectable error exception while booting. +*/ +if (i ==BIST_MEM_INIT_TIMEOUT ) { +printf ("ERROR: Timeout while priming the memory.\n" ); +hang (); + } +} -for (i =0 ; i < (size /4 ); i++) - addr[i] = word; +static void k3_ddrss_lpddr4_preload_full_mem (struct k3_ddrss_desc *ddrss, +u64 total_size,u32 pattern) +{ +u32 done, max_size2; + +/* Get the max size (log2) supported in this config (16/32 lpddr4) +* from the start_addess width - 16bit: 8G, 32bit: 32G +*/ + max_size2 =TH_FLD_WIDTH (LPDDR4__BIST_START_ADDRESS_0__FLD ) + +TH_FLD_WIDTH (LPDDR4__BIST_START_ADDRESS_1__FLD ) +1 ; + +/* ECC is enabled in dt but we can't preload the memory if +* the memory configuration is recognized and supported. +*/ +if (!total_size || total_size > (1ull << max_size2) || + total_size & (total_size -1 )) { +printf ("ECC: the memory configuration is not supported\n" ); +hang (); + } +printf ("ECC is enabled, priming DDR which will take several seconds.\n" ); + done =get_timer (0 ); +k3_lpddr4_bist_init_mem_region (ddrss,0 , total_size, pattern); +printf ("ECC: priming DDR completed in %lu msec\n" ,get_timer (done)); }static void k3_ddrss_lpddr4_ecc_calc_reserved_mem (struct k3_ddrss_desc *ddrss)
@@ -583,9 +688,10 @@ static void k3_ddrss_lpddr4_ecc_init(struct k3_ddrss_desc *ddrss)writel (DDRSS_ECC_CTRL_REG_ECC_EN |DDRSS_ECC_CTRL_REG_RMW_EN |DDRSS_ECC_CTRL_REG_WR_ALLOC , base +DDRSS_ECC_CTRL_REG ); -/* Preload ECC Mem region with 0's */ -k3_ddrss_preload_ecc_mem_region ((u32 *)ecc_region_start, ecc_range, -0x00000000 ); +/* Preload the full memory with 0's using the BIST engine of +* the LPDDR4 controller. +*/ +k3_ddrss_lpddr4_preload_full_mem (ddrss, gd->ram_size,0 );/* Clear Error Count Register */ writel (0x1 , base +DDRSS_ECC_1B_ERR_CNT_REG );
Signature · 1 line
2.34.1
PATCH v6 3/9 ram: k3-ddrss: Add k3_ddrss_ddr_bank_base_size_calc() to solve 'calculations restricted to 32 bits' issue
In reply to Santhosh Kumar KAs R5 is a 32 bit processor, the RAM banks' base and size calculation is restricted to 32 bits, which results in wrong values if bank's base is greater than 32 bits or bank's size is greater than or equal to 4GB.
So, add k3_ddrss_ddr_bank_base_size_calc() to get the base address and size of RAM's banks from the device tree memory node, and store in a 64 bit device private data which can be used for ECC reserved memory calculation, Setting ECC range and Fixing up bank size in device tree when ECC is enabled.
--- drivers/ram/k3-ddrss/k3-ddrss.c | 72 ++++++++++++++++++++++++++------- 1 file changed, 57 insertions(+), 15 deletions(-)
drivers/ram/k3-ddrss/k3-ddrss.c +57 -15
@@ -147,6 +147,9 @@ struct k3_ddrss_desc {struct k3_ddrss_ecc_region ecc_regions[K3_DDRSS_MAX_ECC_REGIONS ];u64 ecc_reserved_space;bool ti_ecc_enabled; +u64 ddr_bank_base[CONFIG_NR_DRAM_BANKS ]; +u64 ddr_bank_size[CONFIG_NR_DRAM_BANKS ]; +u64 ddr_ram_size; };struct reginitdata {
@@ -663,11 +666,54 @@ static void k3_ddrss_lpddr4_preload_full_mem(struct k3_ddrss_desc *ddrss,printf ("ECC: priming DDR completed in %lu msec\n" ,get_timer (done)); } +static void k3_ddrss_ddr_bank_base_size_calc (struct k3_ddrss_desc *ddrss) +{ +int bank, na, ns, len, parent; +const fdt32_t *ptr, *end; + +for (bank =0 ; bank <CONFIG_NR_DRAM_BANKS ; bank++) { + ddrss->ddr_bank_base[bank] =0 ; + ddrss->ddr_bank_size[bank] =0 ; + } + +ofnode mem =ofnode_null (); + +do { + mem =ofnode_by_prop_value (mem,"device_type" ,"memory" ,7 ); + }while (!ofnode_is_enabled (mem)); + +const void *fdt =ofnode_to_fdt (mem); +int node =ofnode_to_offset (mem); +const char *property ="reg" ; + + parent =fdt_parent_offset (fdt, node); + na =fdt_address_cells (fdt, parent); + ns =fdt_size_cells (fdt, parent); + ptr =fdt_getprop (fdt, node, property, &len); + end = ptr + len /sizeof (*ptr); + +for (bank =0 ; bank <CONFIG_NR_DRAM_BANKS ; bank++) { +if (ptr + na + ns <= end) { +if (CONFIG_IS_ENABLED (OF_TRANSLATE )) + ddrss->ddr_bank_base[bank] =fdt_translate_address (fdt, node, ptr); +else + ddrss->ddr_bank_base[bank] =fdtdec_get_number (ptr, na); + + ddrss->ddr_bank_size[bank] =fdtdec_get_number (&ptr[na], ns); + } + + ptr += na + ns; + } + +for (bank =0 ; bank <CONFIG_NR_DRAM_BANKS ; bank++) + ddrss->ddr_ram_size += ddrss->ddr_bank_size[bank]; +} +static void k3_ddrss_lpddr4_ecc_calc_reserved_mem (struct k3_ddrss_desc *ddrss) {fdtdec_setup_mem_size_base_lowest (); - ddrss->ecc_reserved_space = gd->ram_size; + ddrss->ecc_reserved_space = ddrss->ddr_ram_size;do_div (ddrss->ecc_reserved_space,9 );/* Round to clean number */
@@ -691,7 +737,7 @@ static void k3_ddrss_lpddr4_ecc_init(struct k3_ddrss_desc *ddrss)/* Preload the full memory with 0's using the BIST engine of * the LPDDR4 controller. */ -k3_ddrss_lpddr4_preload_full_mem (ddrss, gd->ram_size,0 ); +k3_ddrss_lpddr4_preload_full_mem (ddrss, ddrss->ddr_ram_size,0 );/* Clear Error Count Register */ writel (0x1 , base +DDRSS_ECC_1B_ERR_CNT_REG );
@@ -736,6 +782,8 @@ static int k3_ddrss_probe(struct udevice *dev)k3_lpddr4_start (ddrss); +k3_ddrss_ddr_bank_base_size_calc (ddrss); +if (ddrss->ti_ecc_enabled) {if (!ddrss->ddrss_ss_cfg) { printf("%s: ss_cfg is required if ecc is enabled but not provided.",
@@ -756,30 +804,24 @@ static int k3_ddrss_probe(struct udevice *dev)int k3_ddrss_ddr_fdt_fixup (struct udevice *dev,void *blob,struct bd_info *bd) { -struct k3_ddrss_desc *ddrss =dev_get_priv (dev); -u64 start[CONFIG_NR_DRAM_BANKS ]; -u64 size[CONFIG_NR_DRAM_BANKS ];int bank; +struct k3_ddrss_desc *ddrss =dev_get_priv (dev);if (ddrss->ecc_reserved_space ==0 )return 0 ;for (bank =CONFIG_NR_DRAM_BANKS -1 ; bank >=0 ; bank--) { -if (ddrss->ecc_reserved_space > bd->bi_dram[bank].size) { - ddrss->ecc_reserved_space -= bd->bi_dram[bank].size; - bd->bi_dram[bank].size =0 ; +if (ddrss->ecc_reserved_space > ddrss->ddr_bank_size[bank]) { + ddrss->ecc_reserved_space -= ddrss->ddr_bank_size[bank]; + ddrss->ddr_bank_size[bank] =0 ; }else { - bd->bi_dram[bank].size -= ddrss->ecc_reserved_space; + ddrss->ddr_bank_size[bank] -= ddrss->ecc_reserved_space;break ; } } -for (bank =0 ; bank <CONFIG_NR_DRAM_BANKS ; bank++) { - start[bank] = bd->bi_dram[bank].start; - size[bank] = bd->bi_dram[bank].size; - } - -return fdt_fixup_memory_banks (blob, start, size,CONFIG_NR_DRAM_BANKS ); +return fdt_fixup_memory_banks (blob, ddrss->ddr_bank_base, + ddrss->ddr_bank_size,CONFIG_NR_DRAM_BANKS ); }static int k3_ddrss_get_info (struct udevice *dev,struct ram_info *info)
Signature · 1 line
2.34.1
PATCH v6 4/9 ram: k3-ddrss: Setup ECC region start and range
In reply to Santhosh Kumar KSetup the ECC region's start and range using the device private data, ddrss->ddr_bank_base[0] and ddrss->ddr_ram_size. Also, move start and range of ECC regions from 32 bits to 64 bits to accommodate for DDR greater than or equal to 4GB.
--- drivers/ram/k3-ddrss/k3-ddrss.c | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-)
drivers/ram/k3-ddrss/k3-ddrss.c +8 -8
@@ -121,8 +121,8 @@ struct k3_msmc {#define K3_DDRSS_MAX_ECC_REGIONS 3struct k3_ddrss_ecc_region { -u32 start; -u32 range; +u64 start; +u64 range; };struct k3_ddrss_desc {
@@ -546,7 +546,7 @@ void k3_lpddr4_start(struct k3_ddrss_desc *ddrss) } } -static void k3_ddrss_set_ecc_range_r0 (u32 base,u32 start_address,u32 size) +static void k3_ddrss_set_ecc_range_r0 (u32 base,u64 start_address,u64 size) {writel ((start_address) >>16 , base +DDRSS_ECC_R0_STR_ADDR_REG );writel ((start_address + size -1 ) >>16 , base +DDRSS_ECC_R0_END_ADDR_REG );
@@ -722,13 +722,13 @@ static void k3_ddrss_lpddr4_ecc_calc_reserved_mem(struct k3_ddrss_desc *ddrss)static void k3_ddrss_lpddr4_ecc_init (struct k3_ddrss_desc *ddrss) { -u32 ecc_region_start = ddrss->ecc_regions[0 ].start; -u32 ecc_range = ddrss->ecc_regions[0 ].range; +u64 ecc_region_start = ddrss->ecc_regions[0 ].start; +u64 ecc_range = ddrss->ecc_regions[0 ].range;u32 base = (u32 )ddrss->ddrss_ss_cfg;u32 val;/* Only Program region 0 which covers full ddr space */ -k3_ddrss_set_ecc_range_r0 (base, ecc_region_start - gd->ram_base, ecc_range); +k3_ddrss_set_ecc_range_r0 (base, ecc_region_start - ddrss->ddr_bank_base[0 ], ecc_range);/* Enable ECC, RMW, WR_ALLOC */ writel(DDRSS_ECC_CTRL_REG_ECC_EN | DDRSS_ECC_CTRL_REG_RMW_EN |
@@ -794,8 +794,8 @@ static int k3_ddrss_probe(struct udevice *dev)k3_ddrss_lpddr4_ecc_calc_reserved_mem (ddrss);/* Always configure one region that covers full DDR space */ - ddrss->ecc_regions[0 ].start = gd->ram_base; - ddrss->ecc_regions[0 ].range = gd->ram_size - ddrss->ecc_reserved_space; + ddrss->ecc_regions[0 ].start = ddrss->ddr_bank_base[0 ]; + ddrss->ecc_regions[0 ].range = ddrss->ddr_ram_size - ddrss->ecc_reserved_space;k3_ddrss_lpddr4_ecc_init (ddrss); }
Signature · 1 line
2.34.1
PATCH v6 5/9 ram: k3-ddrss: Enable ECC interrupts
In reply to Santhosh Kumar KEnable ECC 1-bit error, 2-bit error, multiple 1-bit error interrupts by setting the respective bits in the DDRSS_V2A_INT_SET_REG register.
--- drivers/ram/k3-ddrss/k3-ddrss.c | 8 ++++++++ 1 file changed, 8 insertions(+)
drivers/ram/k3-ddrss/k3-ddrss.c +8 -0
@@ -45,6 +45,11 @@#define DDRSS_ECC_R2_STR_ADDR_REG 0x0140#define DDRSS_ECC_R2_END_ADDR_REG 0x0144#define DDRSS_ECC_1B_ERR_CNT_REG 0x0150 +#define DDRSS_V2A_INT_SET_REG 0x00a8 + +#define DDRSS_V2A_INT_SET_REG_ECC1BERR_EN BIT(3) +#define DDRSS_V2A_INT_SET_REG_ECC2BERR_EN BIT(4) +#define DDRSS_V2A_INT_SET_REG_ECCM1BERR_EN BIT(5)#define SINGLE_DDR_SUBSYSTEM 0x1#define MULTI_DDR_SUBSYSTEM 0x2
@@ -742,6 +747,9 @@ static void k3_ddrss_lpddr4_ecc_init(struct k3_ddrss_desc *ddrss)/* Clear Error Count Register */ writel (0x1 , base +DDRSS_ECC_1B_ERR_CNT_REG ); +writel (DDRSS_V2A_INT_SET_REG_ECC1BERR_EN |DDRSS_V2A_INT_SET_REG_ECC2BERR_EN | +DDRSS_V2A_INT_SET_REG_ECCM1BERR_EN , base +DDRSS_V2A_INT_SET_REG ); +/* Enable ECC Check */ val =readl (base +DDRSS_ECC_CTRL_REG ); val |=DDRSS_ECC_CTRL_REG_ECC_CK ;
Signature · 1 line
2.34.1
PATCH v6 6/9 drivers: ram: Kconfig: Add CONFIG_K3_INLINE_ECC
In reply to Santhosh Kumar KFrom: Neha Malcom Francis <[email protected]>
Add CONFIG_K3_INLINE_ECC so that ECC functions can be compiled into R5 SPL only when the config has been enabled.
--- drivers/ram/Kconfig | 10 ++++++++++ 1 file changed, 10 insertions(+)
drivers/ram/Kconfig +10 -0
@@ -116,6 +116,16 @@ config IMXRT_SDRAM to support external memories like sdram, psram & nand. This driver is for the sdram memory interface with the SEMC. +config K3_INLINE_ECC + bool "Enable TI Inline ECC support" + depends on K3_DDRSS + help + Enable Inline ECC support on K3 platforms. 1/9th of the SDRAM space + is used for ECC storage and the rest 8/9th is available for system + use. Enabling ECC increases boot time as the ECC protected regions + need to be primed with a predefined value prior to enabling ECC + check. + source "drivers/ram/aspeed/Kconfig" source "drivers/ram/cadence/Kconfig" source "drivers/ram/octeon/Kconfig"
Signature · 1 line
2.34.1
PATCH v6 7/9 ram: k3-ddrss: Remove 'ti,ecc-enable' support
In reply to Santhosh Kumar KThe functionality of enabling Inline ECC is now controlled by CONFIG_K3_INLINE_ECC. So, remove the support for 'ti,ecc-enable' property to avoid redundancy and to ensure the Inline ECC feature is mananged through build-time config.
--- drivers/ram/k3-ddrss/k3-ddrss.c | 5 +---- 1 file changed, 1 insertion(+), 4 deletions(-)
drivers/ram/k3-ddrss/k3-ddrss.c +1 -4
@@ -151,7 +151,6 @@ struct k3_ddrss_desc {lpddr4_privatedata pd;struct k3_ddrss_ecc_region ecc_regions[K3_DDRSS_MAX_ECC_REGIONS ];u64 ecc_reserved_space; -bool ti_ecc_enabled;u64 ddr_bank_base[CONFIG_NR_DRAM_BANKS ];u64 ddr_bank_size[CONFIG_NR_DRAM_BANKS ];u64 ddr_ram_size;
@@ -408,8 +407,6 @@ static int k3_ddrss_ofdata_to_priv(struct udevice *dev)if (ret)dev_err (dev,"ddr fhs cnt not populated %d\n" , ret); - ddrss->ti_ecc_enabled =dev_read_bool (dev,"ti,ecc-enable" ); -return ret; }
@@ -792,7 +789,7 @@ static int k3_ddrss_probe(struct udevice *dev)k3_ddrss_ddr_bank_base_size_calc (ddrss); -if (ddrss->ti_ecc_enabled) { +if (IS_ENABLED (CONFIG_K3_INLINE_ECC )) {if (!ddrss->ddrss_ss_cfg) {printf ("%s: ss_cfg is required if ecc is enabled but not provided." , __func__);
Signature · 1 line
2.34.1
PATCH v6 8/9 arm: mach-k3: Set NR_DRAM_BANKS to 2
In reply to Santhosh Kumar KFrom: Neha Malcom Francis <[email protected]>
Set CONFIG_NR_DRAM_BANKS to 2 as we have two banks described in the memory/ node for lower and higher addressible DDR regions.
This allows use of FDT functions from fdt_support.c to set up and fix up the memory/ node correctly.
--- arch/arm/mach-k3/Kconfig | 3 +++ configs/am62ax_evm_a53_defconfig | 1 - configs/am62px_evm_a53_defconfig | 1 - configs/am62x_evm_a53_defconfig | 1 - configs/am62x_evm_r5_defconfig | 1 - configs/am64x_evm_a53_defconfig | 1 - configs/am64x_evm_r5_defconfig | 1 - configs/am65x_evm_a53_defconfig | 1 - configs/am65x_evm_r5_defconfig | 1 - configs/am65x_evm_r5_usbdfu_defconfig | 1 - configs/am65x_evm_r5_usbmsc_defconfig | 1 - configs/j7200_evm_a72_defconfig | 1 - configs/j721e_evm_a72_defconfig | 1 - configs/j721s2_evm_a72_defconfig | 1 - configs/j722s_evm_a53_defconfig | 1 - configs/j784s4_evm_a72_defconfig | 1 - 16 files changed, 3 insertions(+), 15 deletions(-)
arch/arm/mach-k3/Kconfig +3 -0
@@ -156,6 +156,9 @@ config K3_X509_SWRV help SWRV for X509 certificate used for boot images +config NR_DRAM_BANKS + default 2 + if CPU_V7R source "arch/arm/mach-k3/r5/Kconfig" endif
configs/am62ax_evm_a53_defconfig +0 -1
@@ -3,7 +3,6 @@ CONFIG_ARCH_K3=y CONFIG_SYS_MALLOC_F_LEN=0x8000 CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 CONFIG_SOC_K3_AM62A7=y CONFIG_TARGET_AM62A7_A53_EVM=y CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
configs/am62px_evm_a53_defconfig +0 -1
@@ -4,7 +4,6 @@ CONFIG_SYS_MALLOC_F_LEN=0x8000 CONFIG_SPL_GPIO=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 CONFIG_SOC_K3_AM62P5=y CONFIG_TARGET_AM62P5_A53_EVM=y CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
configs/am62x_evm_a53_defconfig +0 -1
@@ -3,7 +3,6 @@ CONFIG_ARCH_K3=y CONFIG_SYS_MALLOC_F_LEN=0x8000 CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 CONFIG_SOC_K3_AM625=y CONFIG_TARGET_AM625_A53_EVM=y CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
configs/am62x_evm_r5_defconfig +0 -1
@@ -4,7 +4,6 @@ CONFIG_SYS_MALLOC_LEN=0x08000000 CONFIG_SYS_MALLOC_F_LEN=0x9000 CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 CONFIG_SOC_K3_AM625=y CONFIG_TARGET_AM625_R5_EVM=y CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
configs/am64x_evm_a53_defconfig +0 -1
@@ -6,7 +6,6 @@ CONFIG_SYS_MALLOC_F_LEN=0x8000 CONFIG_SPL_GPIO=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 CONFIG_SOC_K3_AM642=y CONFIG_K3_ATF_LOAD_ADDR=0x701c0000 CONFIG_TARGET_AM642_A53_EVM=y
configs/am64x_evm_r5_defconfig +0 -1
@@ -5,7 +5,6 @@ CONFIG_SYS_MALLOC_F_LEN=0x80000 CONFIG_SPL_GPIO=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 CONFIG_SOC_K3_AM642=y CONFIG_TARGET_AM642_R5_EVM=y CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
configs/am65x_evm_a53_defconfig +0 -1
@@ -5,7 +5,6 @@ CONFIG_SYS_MALLOC_LEN=0x2000000 CONFIG_SYS_MALLOC_F_LEN=0x8000 CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 CONFIG_SOC_K3_AM654=y CONFIG_TARGET_AM654_A53_EVM=y CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
configs/am65x_evm_r5_defconfig +0 -1
@@ -5,7 +5,6 @@ CONFIG_SYS_MALLOC_F_LEN=0x55000 CONFIG_SPL_GPIO=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 CONFIG_SOC_K3_AM654=y CONFIG_K3_EARLY_CONS=y CONFIG_TARGET_AM654_R5_EVM=y
configs/am65x_evm_r5_usbdfu_defconfig +0 -1
@@ -5,7 +5,6 @@ CONFIG_SYS_MALLOC_F_LEN=0x55000 CONFIG_SPL_GPIO=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 CONFIG_SOC_K3_AM654=y CONFIG_K3_EARLY_CONS=y CONFIG_TARGET_AM654_R5_EVM=y
configs/am65x_evm_r5_usbmsc_defconfig +0 -1
@@ -5,7 +5,6 @@ CONFIG_SYS_MALLOC_F_LEN=0x55000 CONFIG_SPL_GPIO=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 CONFIG_SOC_K3_AM654=y CONFIG_K3_EARLY_CONS=y CONFIG_TARGET_AM654_R5_EVM=y
configs/j7200_evm_a72_defconfig +0 -1
@@ -5,7 +5,6 @@ CONFIG_SYS_MALLOC_F_LEN=0x8000 CONFIG_SPL_GPIO=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 CONFIG_SOC_K3_J721E=y CONFIG_TARGET_J7200_A72_EVM=y CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
configs/j721e_evm_a72_defconfig +0 -1
@@ -5,7 +5,6 @@ CONFIG_SYS_MALLOC_F_LEN=0x8000 CONFIG_SPL_GPIO=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 CONFIG_SOC_K3_J721E=y CONFIG_TARGET_J721E_A72_EVM=y CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
configs/j721s2_evm_a72_defconfig +0 -1
@@ -5,7 +5,6 @@ CONFIG_SYS_MALLOC_F_LEN=0x8000 CONFIG_SPL_GPIO=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 CONFIG_SOC_K3_J721S2=y CONFIG_TARGET_J721S2_A72_EVM=y CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
configs/j722s_evm_a53_defconfig +0 -1
@@ -4,7 +4,6 @@ CONFIG_SYS_MALLOC_F_LEN=0x8000 CONFIG_SPL_GPIO=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 CONFIG_SOC_K3_J722S=y CONFIG_TARGET_J722S_A53_EVM=y CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
configs/j784s4_evm_a72_defconfig +0 -1
@@ -5,7 +5,6 @@ CONFIG_SYS_MALLOC_F_LEN=0x8000 CONFIG_SPL_GPIO=y CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y -CONFIG_NR_DRAM_BANKS=2 CONFIG_SOC_K3_J784S4=y CONFIG_TARGET_J784S4_A72_EVM=y CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
Signature · 1 line
2.34.1
PATCH v6 9/9 board: ti: Pull redundant DDR functions to a common location and Fixup DDR size when ECC is enabled
In reply to Santhosh Kumar KAs there are few redundant functions in board/ti/*/evm.c files, pull them to a common location of access to reuse and include the common file to access the functions.
Call k3-ddrss driver through fixup_ddr_driver_for_ecc() to fixup the device tree and resize the available amount of DDR, if ECC is enabled. Otherwise, fixup the device tree using the regular fdt_fixup_memory_banks().
Also call dram_init_banksize() after every call to fixup_ddr_driver_for_ecc() is made so that gd->bd is populated correctly.
Ensure that fixup_ddr_driver_for_ecc() is agnostic to the number of DDR controllers present.
--- arch/arm/mach-k3/Makefile | 2 +- arch/arm/mach-k3/include/mach/k3-ddr.h | 15 ++++++ arch/arm/mach-k3/k3-ddr.c | 72 +++++++++++++++++++++++++ board/ti/am62ax/evm.c | 17 +++--- board/ti/am62px/evm.c | 17 +++--- board/ti/am62x/evm.c | 63 +++------------------- board/ti/am64x/evm.c | 73 +++----------------------- board/ti/am65x/evm.c | 29 +--------- board/ti/common/Makefile | 1 + board/ti/common/k3-ddr.c | 33 ++++++++++++ board/ti/common/k3-ddr.h | 12 +++++ board/ti/j721e/evm.c | 29 +--------- board/ti/j721s2/evm.c | 35 ++++-------- board/ti/j722s/evm.c | 17 +++--- board/ti/j784s4/evm.c | 17 +++--- 15 files changed, 200 insertions(+), 232 deletions(-) create mode 100644 arch/arm/mach-k3/include/mach/k3-ddr.h create mode 100644 arch/arm/mach-k3/k3-ddr.c create mode 100644 board/ti/common/k3-ddr.c create mode 100644 board/ti/common/k3-ddr.h
arch/arm/mach-k3/Makefile +1 -1
@@ -6,7 +6,7 @@ obj-$(CONFIG_ARM64) += arm64/ obj-$(CONFIG_CPU_V7R) += r5/ obj-$(CONFIG_OF_LIBFDT) += common_fdt.o -obj-y += common.o security.o +obj-y += common.o security.o k3-ddr.o obj-$(CONFIG_SOC_K3_AM62A7) += am62ax/ obj-$(CONFIG_SOC_K3_AM62P5) += am62px/ obj-$(CONFIG_SOC_K3_AM625) += am62x/
arch/arm/mach-k3/include/mach/k3-ddr.h new file +15 -0
@@ -0,0 +1,15 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright (C) 2024, Texas Instruments Incorporated - https://www.ti.com/ +*/ + +#ifndef _K3_DDR_H_ +#define _K3_DDR_H_ + +int dram_init (void ); +int dram_init_banksize (void ); + +void fixup_ddr_driver_for_ecc (struct spl_image_info *spl_image); +void fixup_memory_node (struct spl_image_info *spl_image); + +#endif /* _K3_DDR_H_ */
arch/arm/mach-k3/k3-ddr.c new file +72 -0
72 lines not on this page · raw message
board/ti/am62ax/evm.c +10 -7
@@ -12,6 +12,7 @@#include <env.h> #include <fdt_support.h> #include <spl.h> +#include <asm/arch/k3-ddr.h> #include "../common/fdt_ops.h"
@@ -20,15 +21,17 @@ int board_init(void)return 0 ; } -int dram_init (void ) +#if defined(CONFIG_XPL_BUILD ) +void spl_perform_fixups (struct spl_image_info *spl_image) { -return fdtdec_setup_mem_size_base (); -} - -int dram_init_banksize (void ) -{ -return fdtdec_setup_memory_banksize (); +if (IS_ENABLED (CONFIG_K3_DDRSS )) { +if (IS_ENABLED (CONFIG_K3_INLINE_ECC )) +fixup_ddr_driver_for_ecc (spl_image); + }else { +fixup_memory_node (spl_image); + } } +#endif #ifdef CONFIG_BOARD_LATE_INIT int board_late_init (void )
board/ti/am62px/evm.c +10 -7
@@ -13,6 +13,7 @@#include <env.h> #include <fdt_support.h> #include <spl.h> +#include <asm/arch/k3-ddr.h> #include "../common/fdt_ops.h" struct efi_fw_image fw_images[] = {
@@ -53,15 +54,17 @@ int board_init(void)return 0 ; } -int dram_init (void ) +#if defined(CONFIG_XPL_BUILD ) +void spl_perform_fixups (struct spl_image_info *spl_image) { -return fdtdec_setup_mem_size_base (); -} - -int dram_init_banksize (void ) -{ -return fdtdec_setup_memory_banksize (); +if (IS_ENABLED (CONFIG_K3_DDRSS )) { +if (IS_ENABLED (CONFIG_K3_INLINE_ECC )) +fixup_ddr_driver_for_ecc (spl_image); + }else { +fixup_memory_node (spl_image); + } } +#endif #if IS_ENABLED (CONFIG_BOARD_LATE_INIT )int board_late_init (void )
board/ti/am62x/evm.c +7 -56
90 lines not on this page · raw message
board/ti/am64x/evm.c +7 -66
93 lines not on this page · raw message
board/ti/am65x/evm.c +1 -28
@@ -20,6 +20,7 @@#include <env.h> #include <spl.h> #include <linux/printk.h> +#include <asm/arch/k3-ddr.h> #include "../common/board_detect.h" #include "../common/fdt_ops.h"
@@ -49,17 +50,6 @@ int board_init(void)return 0 ; } -int dram_init (void ) -{ -#ifdef CONFIG_PHYS_64BIT - gd->ram_size =0x100000000 ; -#else - gd->ram_size =0x80000000 ; -#endif - -return 0 ; -} -phys_addr_t board_get_usable_ram_top (phys_size_t total_size) {#ifdef CONFIG_PHYS_64BIT
@@ -71,23 +61,6 @@ phys_addr_t board_get_usable_ram_top(phys_size_t total_size)return gd->ram_top; } -int dram_init_banksize (void ) -{ -/* Bank 0 declares the memory available in the DDR low region */ - gd->bd->bi_dram[0 ].start =0x80000000 ; - gd->bd->bi_dram[0 ].size =0x80000000 ; - gd->ram_size =0x80000000 ; - -#ifdef CONFIG_PHYS_64BIT -/* Bank 1 declares the memory available in the DDR high region */ - gd->bd->bi_dram[1 ].start =0x880000000 ; - gd->bd->bi_dram[1 ].size =0x80000000 ; - gd->ram_size =0x100000000 ; -#endif - -return 0 ; -} -#ifdef CONFIG_SPL_LOAD_FIT int board_fit_config_name_match (const char *name) {
board/ti/common/Makefile +1 -0
@@ -4,3 +4,4 @@ obj-${CONFIG_TI_I2C_BOARD_DETECT} += board_detect.o obj-${CONFIG_CMD_EXTENSION} += cape_detect.o obj-${CONFIG_OF_LIBFDT} += fdt_ops.o +obj-${CONFIG_ARCH_K3} += k3-ddr.o
board/ti/common/k3-ddr.c new file +33 -0
@@ -0,0 +1,33 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (C) 2024, Texas Instruments Incorporated - https://www.ti.com/ +*/ + +#include <fdt_support.h> +#include <dm/uclass.h> +#include <k3-ddrss.h> +#include <spl.h> + +#include "k3-ddr.h" + +int dram_init (void ) +{ +s32 ret; + + ret =fdtdec_setup_mem_size_base_lowest (); +if (ret) +printf ("Error setting up mem size and base. %d\n" , ret); + +return ret; +} + +int dram_init_banksize (void ) +{ +s32 ret; + + ret =fdtdec_setup_memory_banksize (); +if (ret) +printf ("Error setting up memory banksize. %d\n" , ret); + +return ret; +}
board/ti/common/k3-ddr.h new file +12 -0
@@ -0,0 +1,12 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright (C) 2024, Texas Instruments Incorporated - https://www.ti.com/ +*/ + +#ifndef __K3_DDR_INIT_H +#define __K3_DDR_INIT_H + +int dram_init (void ); +int dram_init_banksize (void ); + +#endif /* __K3_DDR_INIT_H */
board/ti/j721e/evm.c +1 -28
@@ -15,6 +15,7 @@#include <asm/gpio.h> #include <spl.h> #include <dm.h> +#include <asm/arch/k3-ddr.h> #include "../common/board_detect.h" #include "../common/fdt_ops.h"
@@ -77,17 +78,6 @@ int board_init(void)return 0 ; } -int dram_init (void ) -{ -#ifdef CONFIG_PHYS_64BIT - gd->ram_size =0x100000000 ; -#else - gd->ram_size =0x80000000 ; -#endif - -return 0 ; -} -phys_addr_t board_get_usable_ram_top (phys_size_t total_size) {#ifdef CONFIG_PHYS_64BIT
@@ -99,23 +89,6 @@ phys_addr_t board_get_usable_ram_top(phys_size_t total_size)return gd->ram_top; } -int dram_init_banksize (void ) -{ -/* Bank 0 declares the memory available in the DDR low region */ - gd->bd->bi_dram[0 ].start =0x80000000 ; - gd->bd->bi_dram[0 ].size =0x80000000 ; - gd->ram_size =0x80000000 ; - -#ifdef CONFIG_PHYS_64BIT -/* Bank 1 declares the memory available in the DDR high region */ - gd->bd->bi_dram[1 ].start =0x880000000 ; - gd->bd->bi_dram[1 ].size =0x80000000 ; - gd->ram_size =0x100000000 ; -#endif - -return 0 ; -} -#ifdef CONFIG_SPL_LOAD_FIT int board_fit_config_name_match (const char *name) {
board/ti/j721s2/evm.c +10 -25
@@ -21,6 +21,7 @@#include <dm.h> #include <dm/uclass-internal.h> #include <dm/root.h> +#include <asm/arch/k3-ddr.h> #include "../common/board_detect.h" #include "../common/fdt_ops.h"
@@ -32,17 +33,6 @@ int board_init(void)return 0 ; } -int dram_init (void ) -{ -#ifdef CONFIG_PHYS_64BIT - gd->ram_size =0x100000000 ; -#else - gd->ram_size =0x80000000 ; -#endif - -return 0 ; -} -phys_addr_t board_get_usable_ram_top (phys_size_t total_size) {#ifdef CONFIG_PHYS_64BIT
@@ -54,22 +44,17 @@ phys_addr_t board_get_usable_ram_top(phys_size_t total_size)return gd->ram_top; } -int dram_init_banksize (void ) +#if defined(CONFIG_XPL_BUILD ) +void spl_perform_fixups (struct spl_image_info *spl_image) { -/* Bank 0 declares the memory available in the DDR low region */ - gd->bd->bi_dram[0 ].start =0x80000000 ; - gd->bd->bi_dram[0 ].size =0x7fffffff ; - gd->ram_size =0x80000000 ; - -#ifdef CONFIG_PHYS_64BIT -/* Bank 1 declares the memory available in the DDR high region */ - gd->bd->bi_dram[1 ].start =0x880000000 ; - gd->bd->bi_dram[1 ].size =0x37fffffff ; - gd->ram_size =0x400000000 ; -#endif - -return 0 ; +if (IS_ENABLED (CONFIG_K3_DDRSS )) { +if (IS_ENABLED (CONFIG_K3_INLINE_ECC )) +fixup_ddr_driver_for_ecc (spl_image); + }else { +fixup_memory_node (spl_image); + } } +#endif #ifdef CONFIG_TI_I2C_BOARD_DETECT /*
board/ti/j722s/evm.c +10 -7
@@ -12,6 +12,7 @@#include <env.h> #include <fdt_support.h> #include <spl.h> +#include <asm/arch/k3-ddr.h> #include "../common/fdt_ops.h" int board_init (void )
@@ -19,15 +20,17 @@ int board_init(void)return 0 ; } -int dram_init (void ) +#if defined(CONFIG_XPL_BUILD ) +void spl_perform_fixups (struct spl_image_info *spl_image) { -return fdtdec_setup_mem_size_base (); -} - -int dram_init_banksize (void ) -{ -return fdtdec_setup_memory_banksize (); +if (IS_ENABLED (CONFIG_K3_DDRSS )) { +if (IS_ENABLED (CONFIG_K3_INLINE_ECC )) +fixup_ddr_driver_for_ecc (spl_image); + }else { +fixup_memory_node (spl_image); + } } +#endif #if IS_ENABLED (CONFIG_BOARD_LATE_INIT )int board_late_init (void )
board/ti/j784s4/evm.c +10 -7
@@ -10,6 +10,7 @@#include <efi_loader.h> #include <init.h> #include <spl.h> +#include <asm/arch/k3-ddr.h> #include "../common/fdt_ops.h" DECLARE_GLOBAL_DATA_PTR ;
@@ -52,15 +53,17 @@ int board_init(void)return 0 ; } -int dram_init (void ) +#if defined(CONFIG_XPL_BUILD ) +void spl_perform_fixups (struct spl_image_info *spl_image) { -return fdtdec_setup_mem_size_base (); -} - -int dram_init_banksize (void ) -{ -return fdtdec_setup_memory_banksize (); +if (IS_ENABLED (CONFIG_K3_DDRSS )) { +if (IS_ENABLED (CONFIG_K3_INLINE_ECC )) +fixup_ddr_driver_for_ecc (spl_image); + }else { +fixup_memory_node (spl_image); + } } +#endif #ifdef CONFIG_BOARD_LATE_INIT int board_late_init (void )
Signature · 1 line
2.34.1
Quoted 16 lines · Santhosh Kumar K
This series adds support for Inline ECC in DDR for AM64X, AM62X, AM62AX, AM62PX, J721E, J721S2, J722S and J784S4 devices.
(1/9) Add
ss_cfgreg entry
(2/9) Enable ECC priming with BIST engine
(3/9) Add a function to store base address and size of RAM's banks
in a 64-bit device private data
(4/9) Setup the ECC region start and range
(5/9) Enable ECC 1-bit error, 2-bit error and multiple-bit
error interrupts
(6/9) AddCONFIG_K3_INLINE_ECC
(7/9) Remove 'ti,ecc-enable' flag
(8/9) Set defaultNR_DRAM_BANKSto 2
(9/9) Pull Redundant DDR functions to a common location and Fixup
DDR size when ECC is enabled
Quoted 1 line
[...]
Applied to u-boot/master, thanks!
Signature · 1 line
Tom