platform/x86: int3472: Add handshake pin support
cover platform/x86: int3472: Add handshake pin support
New Intel Meteor Lake based laptops with IPU6 cameras have a new type 0x12 pin defined in the INT3472 sensor companion device which describes the sensor's GPIOs.
This pin is primarily used on designs with a Lattice FPGA chip which is capable of running the sensor independently of the main CPU for features like presence detection. This pin needs to be driven high to make the FPGA run the power-on sequence of the sensor. After driving the pin high the FPGA "firmware" needs 25ms to comlpete the power-on sequence.
This series implements support for this by modelling the handshake GPIO as a GPIO driven 'dvdd' regulator with an enable-time of 25 ms, also see:
https://lore.kernel.org/platform-driver-x86/[email protected]/
Patch 1 Is an unrelated cleanup which I had lying around
Patches 2-7 Prepare + Implement the handshake GPIO
Patch 8 Is a small patch adding some extra debugging to GPIO remapping
This series applies on top of pdx86/for-next, for testing with 6.14 this patch needs to be cherry-picked first:
https://web.git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86.git/commit/?id=81b251c66bdfe263fb5e7a16838512ddaeed77df
Regards,
Hans
Hans de Goede (8):
platform/x86: int3472: Add skl_int3472_register_clock() helper platform/x86: int3472: Stop setting a supply-name for GPIO regulators platform/x86: int3472: Drop unused gpio field from struct
int3472_gpio_regulator
platform/x86: int3472: Rework AVDD second sensor quirk handling platform/x86: int3472: Make regulator supply name configurable platform/x86: int3472: Prepare for registering more then 1 GPIO
regulator
platform/x86: int3472: Add handshake pin support platform/x86: int3472: Debug log when remapping pins
drivers/platform/x86/intel/int3472/Makefile | 3 +- .../x86/intel/int3472/clk_and_regulator.c | 163 ++++++------------ drivers/platform/x86/intel/int3472/common.h | 45 +++-- drivers/platform/x86/intel/int3472/discrete.c | 37 +++- .../x86/intel/int3472/discrete_quirks.c | 22 +++ 5 files changed, 139 insertions(+), 131 deletions(-) create mode 100644 drivers/platform/x86/intel/int3472/discrete_quirks.c
Signature · 1 line
2.49.0
PATCH 1/8 platform/x86: int3472: Add skl_int3472_register_clock() helper
skl_int3472_register_dsm_clock() and skl_int3472_register_gpio_clock() are 80% the same code. Factor out the common code into a new skl_int3472_register_clock() helper.
--- .../x86/intel/int3472/clk_and_regulator.c | 57 +++++-------------- 1 file changed, 13 insertions(+), 44 deletions(-)
drivers/platform/x86/intel/int3472/clk_and_regulator.c +13 -44
@@ -118,7 +118,7 @@ static const struct clk_ops skl_int3472_clock_ops = { .recalc_rate = skl_int3472_clk_recalc_rate, }; -int skl_int3472_register_dsm_clock (struct int3472_discrete_device *int3472) +static int skl_int3472_register_clock (struct int3472_discrete_device *int3472) {struct acpi_device *adev = int3472->adev;struct clk_init_data init = {
@@ -127,12 +127,6 @@ int skl_int3472_register_dsm_clock(struct int3472_discrete_device *int3472) };int ret; -if (int3472->clock.cl) -return 0 ;/* A GPIO controlled clk has already been registered */ - -if (!acpi_check_dsm (adev->handle, &img_clk_guid,0 ,BIT (1 ))) -return 0 ;/* DSM clock control is not available */ - init.name =kasprintf (GFP_KERNEL ,"%s-clk" ,acpi_dev_name (adev));if (!init.name)return -ENOMEM ;
@@ -161,51 +155,26 @@ int skl_int3472_register_dsm_clock(struct int3472_discrete_device *int3472)return ret; } +int skl_int3472_register_dsm_clock (struct int3472_discrete_device *int3472) +{ +if (int3472->clock.cl) +return 0 ;/* A GPIO controlled clk has already been registered */ + +if (!acpi_check_dsm (int3472->adev->handle, &img_clk_guid,0 ,BIT (1 ))) +return 0 ;/* DSM clock control is not available */ + +return skl_int3472_register_clock (int3472); +} +int skl_int3472_register_gpio_clock (struct int3472_discrete_device *int3472,struct gpio_desc *gpio) { -struct clk_init_data init = { - .ops = &skl_int3472_clock_ops, - .flags =CLK_GET_RATE_NOCACHE , - }; -int ret; -if (int3472->clock.cl)return -EBUSY ; int3472->clock.ena_gpio = gpio; - init.name =kasprintf (GFP_KERNEL ,"%s-clk" , -acpi_dev_name (int3472->adev)); -if (!init.name) -return -ENOMEM ; - - int3472->clock.frequency =skl_int3472_get_clk_frequency (int3472); - - int3472->clock.clk_hw.init = &init; - int3472->clock.clk =clk_register (&int3472->adev->dev, - &int3472->clock.clk_hw); -if (IS_ERR (int3472->clock.clk)) { - ret =PTR_ERR (int3472->clock.clk); - goto out_free_init_name; - } - - int3472->clock.cl =clkdev_create (int3472->clock.clk,NULL , - int3472->sensor_name); -if (!int3472->clock.cl) { - ret = -ENOMEM ; - goto err_unregister_clk; - } - -kfree (init.name); -return 0 ; - -err_unregister_clk: -clk_unregister (int3472->clock.clk); -out_free_init_name: -kfree (init.name); - -return ret; +return skl_int3472_register_clock (int3472); }void skl_int3472_unregister_clock (struct int3472_discrete_device *int3472)
Signature · 1 line
2.49.0
Re: [PATCH 1/8] platform/x86: int3472: Add skl_int3472_register_clock() helper
Quoted 3 lines · Hans de Goede
skl_int3472_register_dsm_clock()andskl_int3472_register_gpio_clock()are 80% the same code. Factor out the common code into a newskl_int3472_register_clock()helper.
Indeed. Good catch!
Signature · 2 lines
With Best Regards, Andy Shevchenko
PATCH 2/8 platform/x86: int3472: Stop setting a supply-name for GPIO regulators
In reply to Hans de GoedeThe supply_name field is not mandatory and is supposed to be set to the name of another regulator when it is known that the regulator being registered is supplied by that other regulator.
Having a regulator supplying the regulator which is being registered does not apply to the INT3472 GPIO regulator, stop setting a supply_name.
--- drivers/platform/x86/intel/int3472/clk_and_regulator.c | 3 --- drivers/platform/x86/intel/int3472/common.h | 5 +---- 2 files changed, 1 insertion(+), 7 deletions(-)
drivers/platform/x86/intel/int3472/clk_and_regulator.c +0 -3
@@ -256,12 +256,9 @@ int skl_int3472_register_regulator(struct int3472_discrete_device *int3472,snprintf (int3472->regulator.regulator_name,sizeof (int3472->regulator.regulator_name),"%s-regulator" ,acpi_dev_name (int3472->adev)); -snprintf (int3472->regulator.supply_name, -GPIO_REGULATOR_SUPPLY_NAME_LENGTH ,"supply-0" ); int3472->regulator.rdesc =INT3472_REGULATOR ( int3472->regulator.regulator_name, - int3472->regulator.supply_name, &int3472_gpio_regulator_ops); int3472->regulator.gpio = gpio;
drivers/platform/x86/intel/int3472/common.h +1 -4
@@ -27,17 +27,15 @@#define INT3472_MAX_SENSOR_GPIOS 3#define GPIO_REGULATOR_NAME_LENGTH 21 -#define GPIO_REGULATOR_SUPPLY_NAME_LENGTH 9#define GPIO_REGULATOR_SUPPLY_MAP_COUNT 2#define INT3472_LED_MAX_NAME_LEN 32#define CIO2_SENSOR_SSDB_MCLKSPEED_OFFSET 86 -#define INT3472_REGULATOR (_name, _supply, _ops) \ +#define INT3472_REGULATOR (_name, _ops) \ (const struct regulator_desc) { \ .name = _name, \ - .supply_name = _supply, \ .type = REGULATOR_VOLTAGE, \ .ops = _ops, \ .owner = THIS_MODULE, \
@@ -82,7 +80,6 @@ struct int3472_discrete_device {/* SUPPLY_MAP_COUNT * 2 to make room for second sensor mappings */ struct regulator_consumer_supply supply_map[GPIO_REGULATOR_SUPPLY_MAP_COUNT *2 ];char regulator_name[GPIO_REGULATOR_NAME_LENGTH ]; -char supply_name[GPIO_REGULATOR_SUPPLY_NAME_LENGTH ];struct gpio_desc *gpio;struct regulator_dev *rdev;struct regulator_desc rdesc;
Signature · 1 line
2.49.0
Re: [PATCH 2/8] platform/x86: int3472: Stop setting a supply-name for GPIO regulators
Quoted 6 lines · Hans de Goede
The
supply_namefield is not mandatory and is supposed to be set to the name of another regulator when it is known that the regulator being registered is supplied by that other regulator.Having a regulator supplying the regulator which is being registered does not apply to the INT3472 GPIO regulator, stop setting a
supply_name.
Signature · 2 lines
With Best Regards, Andy Shevchenko
PATCH 3/8 platform/x86: int3472: Drop unused gpio field from struct int3472_gpio_regulator
In reply to Hans de GoedeThe gpio field in struct int3472_gpio_regulator is only briefly used to store the gpio in skl_int3472_register_regulator() instead just store the gpio directly into cfg.ena_gpiod an drop the gpio field.
--- drivers/platform/x86/intel/int3472/clk_and_regulator.c | 4 +--- drivers/platform/x86/intel/int3472/common.h | 1 - 2 files changed, 1 insertion(+), 4 deletions(-)
drivers/platform/x86/intel/int3472/clk_and_regulator.c +1 -3
@@ -261,11 +261,9 @@ int skl_int3472_register_regulator(struct int3472_discrete_device *int3472, int3472->regulator.regulator_name, &int3472_gpio_regulator_ops); - int3472->regulator.gpio = gpio; - cfg.dev = &int3472->adev->dev; cfg.init_data = &init_data; - cfg.ena_gpiod = int3472->regulator.gpio; + cfg.ena_gpiod = gpio; int3472->regulator.rdev = regulator_register(int3472->dev, &int3472->regulator.rdesc,
drivers/platform/x86/intel/int3472/common.h +0 -1
@@ -80,7 +80,6 @@ struct int3472_discrete_device {/* SUPPLY_MAP_COUNT * 2 to make room for second sensor mappings */ struct regulator_consumer_supply supply_map[GPIO_REGULATOR_SUPPLY_MAP_COUNT *2 ];char regulator_name[GPIO_REGULATOR_NAME_LENGTH ]; -struct gpio_desc *gpio;struct regulator_dev *rdev;struct regulator_desc rdesc; } regulator;
Signature · 1 line
2.49.0
Re: [PATCH 3/8] platform/x86: int3472: Drop unused gpio field from struct int3472_gpio_regulator
Quoted 1 line · Hans de Goede
The gpio field in struct
int3472_gpio_regulatoris only briefly used to
(no need to change anything on the firs line :)
Quoted 1 line
store the gpio in
skl_int3472_register_regulator()instead just store
GPIO
' instead' --> '. Instead' (otherwise it's a tautology)
Quoted 1 line
the gpio directly into cfg.ena_gpiod an drop the gpio field.
GPIO (only the first occurrence)
Signature · 2 lines
With Best Regards, Andy Shevchenko
PATCH 4/8 platform/x86: int3472: Rework AVDD second sensor quirk handling
In reply to Hans de GoedeRework the discrete quirk handling to use a quirks struct which is pointed to by a dmi_system_id table, rather then having a dmi_system_id table per type of quirk.
This is a preparation patch for adding support for multiple regulators, where not all regulators might be shared between sensors.
--- drivers/platform/x86/intel/int3472/Makefile | 3 +- .../x86/intel/int3472/clk_and_regulator.c | 28 ++----------------- drivers/platform/x86/intel/int3472/common.h | 13 ++++++++- drivers/platform/x86/intel/int3472/discrete.c | 13 ++++++++- .../x86/intel/int3472/discrete_quirks.c | 22 +++++++++++++++ 5 files changed, 50 insertions(+), 29 deletions(-) create mode 100644 drivers/platform/x86/intel/int3472/discrete_quirks.c
drivers/platform/x86/intel/int3472/Makefile +2 -1
@@ -1,7 +1,8 @@ obj-$(CONFIG_INTEL_SKL_INT3472) += intel_skl_int3472_discrete.o \ intel_skl_int3472_tps68470.o \ intel_skl_int3472_common.o -intel_skl_int3472_discrete-y := discrete.o clk_and_regulator.o led.o +intel_skl_int3472_discrete-y := discrete.o discrete_quirks.o \ + clk_and_regulator.o led.o intel_skl_int3472_tps68470-y := tps68470.o tps68470_board_data.o intel_skl_int3472_common-y += common.o
drivers/platform/x86/intel/int3472/clk_and_regulator.c +2 -26
@@ -5,7 +5,6 @@#include <linux/clkdev.h> #include <linux/clk-provider.h> #include <linux/device.h> -#include <linux/dmi.h> #include <linux/gpio/consumer.h> #include <linux/regulator/driver.h> #include <linux/slab.h>
@@ -205,37 +204,14 @@ static const char * const skl_int3472_regulator_map_supplies[] = {static_assert (ARRAY_SIZE (skl_int3472_regulator_map_supplies) ==GPIO_REGULATOR_SUPPLY_MAP_COUNT ); -/* -* On some models there is a single GPIO regulator which is shared between -* sensors and only listed in the ACPI resources of one sensor. -* This DMI table contains the name of the second sensor. This is used to add -* entries for the second sensor to the supply_map. -*/ -static const struct dmi_system_id skl_int3472_regulator_second_sensor[] = { - { -/* Lenovo Miix 510-12IKB */ - .matches = { -DMI_MATCH (DMI_SYS_VENDOR ,"LENOVO" ), -DMI_MATCH (DMI_PRODUCT_VERSION ,"MIIX 510-12IKB" ), - }, - .driver_data ="i2c-OVTI2680:00" , - }, - { } -}; -int skl_int3472_register_regulator (struct int3472_discrete_device *int3472, -struct gpio_desc *gpio) +struct gpio_desc *gpio, +const char *second_sensor) {struct regulator_init_data init_data = { };struct regulator_config cfg = { }; -const char *second_sensor =NULL ; -const struct dmi_system_id *id;int i, j; - id =dmi_first_match (skl_int3472_regulator_second_sensor); -if (id) - second_sensor = id->driver_data; -for (i =0 , j =0 ; i <ARRAY_SIZE (skl_int3472_regulator_map_supplies); i++) { int3472->regulator.supply_map[j].supply = skl_int3472_regulator_map_supplies[i]; int3472->regulator.supply_map[j].dev_name = int3472->sensor_name;
drivers/platform/x86/intel/int3472/common.h +12 -1
@@ -48,6 +48,7 @@ container_of(clk, struct int3472_discrete_device, clock)struct acpi_device ; +struct dmi_system_id ;struct i2c_client ;struct platform_device ;
@@ -68,6 +69,11 @@ struct int3472_cldb {u8 reserved2[17 ]; }; +struct int3472_discrete_quirks { +/* For models where AVDD GPIO is shared between sensors */ +const char *avdd_second_sensor; +}; +struct int3472_discrete_device {struct acpi_device *adev;struct device *dev;
@@ -100,11 +106,15 @@ struct int3472_discrete_device {struct gpio_desc *gpio; } pled; +struct int3472_discrete_quirks quirks; +unsigned int ngpios;/* how many GPIOs have we seen */ unsigned int n_sensor_gpios;/* how many have we mapped to sensor */ struct gpiod_lookup_table gpios; }; +extern const struct dmi_system_id skl_int3472_discrete_quirks[]; +union acpi_object *skl_int3472_get_acpi_buffer (struct acpi_device *adev,char *id);int skl_int3472_fill_cldb (struct acpi_device *adev,struct int3472_cldb *cldb);
@@ -118,7 +128,8 @@ int skl_int3472_register_dsm_clock(struct int3472_discrete_device *int3472);void skl_int3472_unregister_clock (struct int3472_discrete_device *int3472);int skl_int3472_register_regulator (struct int3472_discrete_device *int3472, -struct gpio_desc *gpio); +struct gpio_desc *gpio, +const char *second_sensor);void skl_int3472_unregister_regulator (struct int3472_discrete_device *int3472);int skl_int3472_register_pled (struct int3472_discrete_device *int3472,struct gpio_desc *gpio);
drivers/platform/x86/intel/int3472/discrete.c +12 -1
@@ -5,6 +5,7 @@#include <linux/array_size.h> #include <linux/bitfield.h> #include <linux/device.h> +#include <linux/dmi.h> #include <linux/gpio/consumer.h> #include <linux/gpio/machine.h> #include <linux/i2c.h>
@@ -310,7 +311,8 @@ static int skl_int3472_handle_gpio_resources(struct acpi_resource *ares,break ;case INT3472_GPIO_TYPE_POWER_ENABLE : - ret =skl_int3472_register_regulator (int3472, gpio); + ret =skl_int3472_register_regulator (int3472, gpio, + int3472->quirks.avdd_second_sensor);if (ret) err_msg ="Failed to map regulator to sensor\n" ;
@@ -378,13 +380,19 @@ static void skl_int3472_discrete_remove(struct platform_device *pdev)static int skl_int3472_discrete_probe (struct platform_device *pdev) {struct acpi_device *adev =ACPI_COMPANION (&pdev->dev); +const struct int3472_discrete_quirks *quirks =NULL ;struct int3472_discrete_device *int3472; +const struct dmi_system_id *id;struct int3472_cldb cldb;int ret;if (!adev)return -ENODEV ; + id =dmi_first_match (skl_int3472_discrete_quirks); +if (id) + quirks = id->driver_data; + ret =skl_int3472_fill_cldb (adev, &cldb);if (ret) {dev_err (&pdev->dev,"Couldn't fill CLDB structure\n" );
@@ -408,6 +416,9 @@ static int skl_int3472_discrete_probe(struct platform_device *pdev)platform_set_drvdata (pdev, int3472); int3472->clock.imgclk_index = cldb.clock_source; +if (quirks) + int3472->quirks = *quirks; + ret =skl_int3472_get_sensor_adev_and_name (&pdev->dev, &int3472->sensor, &int3472->sensor_name);if (ret)
drivers/platform/x86/intel/int3472/discrete_quirks.c new file +22 -0
@@ -0,0 +1,22 @@ +// SPDX-License-Identifier: GPL-2.0 +/* Author: Hans de Goede <[email protected]> */ + +#include <linux/dmi.h> + +#include "common.h" + +static const struct int3472_discrete_quirks lenovo_miix_510_quirks = { + .avdd_second_sensor ="i2c-OVTI2680:00" , +}; + +const struct dmi_system_id skl_int3472_discrete_quirks[] = { + { +/* Lenovo Miix 510-12IKB */ + .matches = { +DMI_MATCH (DMI_SYS_VENDOR ,"LENOVO" ), +DMI_MATCH (DMI_PRODUCT_VERSION ,"MIIX 510-12IKB" ), + }, + .driver_data = (void *)&lenovo_miix_510_quirks, + }, + { } +};
Signature · 1 line
2.49.0
PATCH 5/8 platform/x86: int3472: Make regulator supply name configurable
In reply to Hans de GoedeThis is a preparation patch for registering multiple regulators, which requires a different supply-name for each regulator. Make supply-name a parameter to skl_int3472_register_regulator() and use con-id to set it so that the existing int3472_gpio_map remapping can be used with it.
Since supply-name now is a parameter, drop the fixed skl_int3472_regulator_map_supplies[] array and instead add lower- + upper-case mappings of the passed in supply-name to the regulator.
--- .../x86/intel/int3472/clk_and_regulator.c | 47 ++++++++----------- drivers/platform/x86/intel/int3472/common.h | 6 ++- drivers/platform/x86/intel/int3472/discrete.c | 4 +- 3 files changed, 26 insertions(+), 31 deletions(-)
drivers/platform/x86/intel/int3472/clk_and_regulator.c +19 -28
@@ -185,42 +185,34 @@ void skl_int3472_unregister_clock(struct int3472_discrete_device *int3472)clk_unregister (int3472->clock.clk); } -/* -* The INT3472 device is going to be the only supplier of a regulator for -* the sensor device. But unlike the clk framework the regulator framework -* does not allow matching by consumer-device-name only. -* -* Ideally all sensor drivers would use "avdd" as supply-id. But for drivers -* where this cannot be changed because another supply-id is already used in -* e.g. DeviceTree files an alias for the other supply-id can be added here. -* -* Do not forget to update GPIO_REGULATOR_SUPPLY_MAP_COUNT when changing this. -*/ -static const char *const skl_int3472_regulator_map_supplies[] = { -"avdd" , -"AVDD" , -}; - -static_assert (ARRAY_SIZE (skl_int3472_regulator_map_supplies) == -GPIO_REGULATOR_SUPPLY_MAP_COUNT ); -int skl_int3472_register_regulator (struct int3472_discrete_device *int3472,struct gpio_desc *gpio, +const char *supply_name,const char *second_sensor) {struct regulator_init_data init_data = { }; +struct int3472_gpio_regulator *regulator;struct regulator_config cfg = { };int i, j; -for (i =0 , j =0 ; i <ARRAY_SIZE (skl_int3472_regulator_map_supplies); i++) { - int3472->regulator.supply_map[j].supply = skl_int3472_regulator_map_supplies[i]; - int3472->regulator.supply_map[j].dev_name = int3472->sensor_name; +if (strlen (supply_name) >=GPIO_SUPPPLY_NAME_LENGTH ) { +dev_err (int3472->dev,"supply-name '%s' length too long\n" , supply_name); +return -EOVERFLOW ; + } + + regulator = &int3472->regulator; +string_upper (regulator->supply_name_upper, supply_name); + +for (i =0 , j =0 ; i <GPIO_REGULATOR_SUPPLY_MAP_COUNT ; i++) { +const char *supply = i ? regulator->supply_name_upper : supply_name; + + regulator->supply_map[j].supply = supply; + regulator->supply_map[j].dev_name = int3472->sensor_name; j++;if (second_sensor) { - int3472->regulator.supply_map[j].supply = - skl_int3472_regulator_map_supplies[i]; - int3472->regulator.supply_map[j].dev_name = second_sensor; + regulator->supply_map[j].supply = supply; + regulator->supply_map[j].dev_name = second_sensor; j++; } }
@@ -229,9 +221,8 @@ int skl_int3472_register_regulator(struct int3472_discrete_device *int3472, init_data.consumer_supplies = int3472->regulator.supply_map; init_data.num_consumer_supplies = j; -snprintf (int3472->regulator.regulator_name, -sizeof (int3472->regulator.regulator_name),"%s-regulator" , -acpi_dev_name (int3472->adev)); +snprintf (regulator->regulator_name,sizeof (regulator->regulator_name),"%s-%s" , +acpi_dev_name (int3472->adev), supply_name); int3472->regulator.rdesc = INT3472_REGULATOR( int3472->regulator.regulator_name,
drivers/platform/x86/intel/int3472/common.h +5 -1
@@ -26,7 +26,9 @@#define INT3472_PDEV_MAX_NAME_LEN 23#define INT3472_MAX_SENSOR_GPIOS 3 -#define GPIO_REGULATOR_NAME_LENGTH 21 +#define GPIO_SUPPPLY_NAME_LENGTH 5 +#define GPIO_REGULATOR_NAME_LENGTH (12 + GPIO_SUPPPLY_NAME_LENGTH) +/* lower- + upper-case mapping */ #define GPIO_REGULATOR_SUPPLY_MAP_COUNT 2#define INT3472_LED_MAX_NAME_LEN 32
@@ -85,6 +87,7 @@ struct int3472_discrete_device {struct int3472_gpio_regulator {/* SUPPLY_MAP_COUNT * 2 to make room for second sensor mappings */ struct regulator_consumer_supply supply_map[GPIO_REGULATOR_SUPPLY_MAP_COUNT *2 ]; +char supply_name_upper[GPIO_SUPPPLY_NAME_LENGTH ];char regulator_name[GPIO_REGULATOR_NAME_LENGTH ];struct regulator_dev *rdev;struct regulator_desc rdesc;
@@ -129,6 +132,7 @@ void skl_int3472_unregister_clock(struct int3472_discrete_device *int3472);int skl_int3472_register_regulator (struct int3472_discrete_device *int3472,struct gpio_desc *gpio, +const char *supply_name,const char *second_sensor);void skl_int3472_unregister_regulator (struct int3472_discrete_device *int3472);
drivers/platform/x86/intel/int3472/discrete.c +2 -2
@@ -188,7 +188,7 @@ static void int3472_get_con_id_and_polarity(struct acpi_device *adev, u8 *type, *gpio_flags =GPIO_ACTIVE_HIGH ;break ;case INT3472_GPIO_TYPE_POWER_ENABLE : - *con_id ="power-enable" ; + *con_id ="avdd" ; *gpio_flags =GPIO_ACTIVE_HIGH ;break ;default :
@@ -311,7 +311,7 @@ static int skl_int3472_handle_gpio_resources(struct acpi_resource *ares,break ;case INT3472_GPIO_TYPE_POWER_ENABLE : - ret =skl_int3472_register_regulator (int3472, gpio, + ret =skl_int3472_register_regulator (int3472, gpio, con_id, int3472->quirks.avdd_second_sensor);if (ret) err_msg ="Failed to map regulator to sensor\n" ;
Signature · 1 line
2.49.0
Re: [PATCH 5/8] platform/x86: int3472: Make regulator supply name configurable
Quoted 8 lines · Hans de Goede
This is a preparation patch for registering multiple regulators, which requires a different supply-name for each regulator. Make supply-name a parameter to
skl_int3472_register_regulator()and use con-id to set it so that the existingint3472_gpio_mapremapping can be used with it.Since supply-name now is a parameter, drop the fixed skl_int3472_regulator_map_supplies[] array and instead add lower- + upper-case mappings of the passed in supply-name to the regulator.
...
drivers/platform/x86/intel/int3472/clk_and_regulator.c void skl_int3472_unregister_clock(struct int3472_discrete_device *int3472) · line 198
Quoted 1 line
drivers/platform/x86/intel/int3472/clk_and_regulator.c +1
-0+if (strlen (supply_name) >=GPIO_SUPPPLY_NAME_LENGTH ) {
Hmm... This can potentially go up to the page fault. If we are _not_ okay with that, strnlen() should be used.
drivers/platform/x86/intel/int3472/clk_and_regulator.c void skl_int3472_unregister_clock(struct int3472_discrete_device *int3472)
Quoted 3 lines
drivers/platform/x86/intel/int3472/clk_and_regulator.c +2
-0+dev_err (int3472->dev,"supply-name '%s' length too long\n" , supply_name); +return -EOVERFLOW ;
This error code is for integers, we use E2BIG for the string lengths.
Quoted 1 line
drivers/platform/x86/intel/int3472/clk_and_regulator.c +1
-0+ }
Signature · 2 lines
With Best Regards, Andy Shevchenko
Re: [PATCH 5/8] platform/x86: int3472: Make regulator supply name configurable
Hi Andy,
Thank you for all the reviews.
Quoted 10 lines · Andy Shevchenko
Quoted 8 lines · Hans de Goede
This is a preparation patch for registering multiple regulators, which requires a different supply-name for each regulator. Make supply-name a parameter to
skl_int3472_register_regulator()and use con-id to set it so that the existingint3472_gpio_mapremapping can be used with it.Since supply-name now is a parameter, drop the fixed skl_int3472_regulator_map_supplies[] array and instead add lower- + upper-case mappings of the passed in supply-name to the regulator.
Quoted 6 lines
...
drivers/platform/x86/intel/int3472/clk_and_regulator.c void skl_int3472_unregister_clock(struct int3472_discrete_device *int3472) · line 198
Quoted 1 line
drivers/platform/x86/intel/int3472/clk_and_regulator.c +1
-0+if (strlen (supply_name) >=GPIO_SUPPPLY_NAME_LENGTH ) {Hmm... This can potentially go up to the page fault. If we are _not_ okay with that,
strnlen()should be used.
The supply_name is a const string from our own code in discrete.c, which should never get anywhere near the page-size. This is just a sanity check in case we start using longer names and forget to update the GPIO_SUPPPLY_NAME_LENGTH define.
Quoted 5 lines
drivers/platform/x86/intel/int3472/clk_and_regulator.c void skl_int3472_unregister_clock(struct int3472_discrete_device *int3472)
Quoted 3 lines
drivers/platform/x86/intel/int3472/clk_and_regulator.c +2
-0+dev_err (int3472->dev,"supply-name '%s' length too long\n" , supply_name); +return -EOVERFLOW ;This error code is for integers, we use E2BIG for the string lengths.
Ok, will fix for v2.
Regards,
Hans
PATCH 6/8 platform/x86: int3472: Prepare for registering more then 1 GPIO regulator
In reply to Hans de GoedePrepare the discrete code for registering more then 1 GPIO regulator.
--- .../x86/intel/int3472/clk_and_regulator.c | 26 ++++++++++++------- drivers/platform/x86/intel/int3472/common.h | 20 ++++++++------ 2 files changed, 28 insertions(+), 18 deletions(-)
drivers/platform/x86/intel/int3472/clk_and_regulator.c +16 -10
@@ -195,12 +195,17 @@ int skl_int3472_register_regulator(struct int3472_discrete_device *int3472,struct regulator_config cfg = { };int i, j; +if (int3472->n_regulators >=INT3472_MAX_REGULATORS ) { +dev_err (int3472->dev,"Too many regulators mapped\n" ); +return -EINVAL ; + } +if (strlen (supply_name) >=GPIO_SUPPPLY_NAME_LENGTH ) {dev_err (int3472->dev,"supply-name '%s' length too long\n" , supply_name);return -EOVERFLOW ; } - regulator = &int3472->regulator; + regulator = &int3472->regulators[int3472->n_regulators];string_upper (regulator->supply_name_upper, supply_name);for (i =0 , j =0 ; i <GPIO_REGULATOR_SUPPLY_MAP_COUNT ; i++) {
@@ -218,28 +223,29 @@ int skl_int3472_register_regulator(struct int3472_discrete_device *int3472, } init_data.constraints.valid_ops_mask =REGULATOR_CHANGE_STATUS ; - init_data.consumer_supplies = int3472->regulator.supply_map; + init_data.consumer_supplies = regulator->supply_map; init_data.num_consumer_supplies = j;snprintf (regulator->regulator_name,sizeof (regulator->regulator_name),"%s-%s" ,acpi_dev_name (int3472->adev), supply_name); - int3472->regulator.rdesc =INT3472_REGULATOR ( - int3472->regulator.regulator_name, - &int3472_gpio_regulator_ops); + regulator->rdesc =INT3472_REGULATOR (regulator->regulator_name, + &int3472_gpio_regulator_ops); cfg.dev = &int3472->adev->dev; cfg.init_data = &init_data; cfg.ena_gpiod = gpio; - int3472->regulator.rdev =regulator_register (int3472->dev, - &int3472->regulator.rdesc, - &cfg); + regulator->rdev =regulator_register (int3472->dev, ®ulator->rdesc, &cfg); +if (IS_ERR (regulator->rdev)) +return PTR_ERR (regulator->rdev); -return PTR_ERR_OR_ZERO (int3472->regulator.rdev); + int3472->n_regulators++; +return 0 ; }void skl_int3472_unregister_regulator (struct int3472_discrete_device *int3472) { -regulator_unregister (int3472->regulator.rdev); +for (int i =0 ; i < int3472->n_regulators; i++) +regulator_unregister (int3472->regulators[i].rdev); }
drivers/platform/x86/intel/int3472/common.h +12 -8
@@ -25,6 +25,7 @@#define INT3472_PDEV_MAX_NAME_LEN 23#define INT3472_MAX_SENSOR_GPIOS 3 +#define INT3472_MAX_REGULATORS 3#define GPIO_SUPPPLY_NAME_LENGTH 5#define GPIO_REGULATOR_NAME_LENGTH (12 + GPIO_SUPPPLY_NAME_LENGTH)
@@ -76,6 +77,15 @@ struct int3472_discrete_quirks {const char *avdd_second_sensor; }; +struct int3472_gpio_regulator { +/* SUPPLY_MAP_COUNT * 2 to make room for second sensor mappings */ +struct regulator_consumer_supply supply_map[GPIO_REGULATOR_SUPPLY_MAP_COUNT *2 ]; +char supply_name_upper[GPIO_SUPPPLY_NAME_LENGTH ]; +char regulator_name[GPIO_REGULATOR_NAME_LENGTH ]; +struct regulator_dev *rdev; +struct regulator_desc rdesc; +}; +struct int3472_discrete_device {struct acpi_device *adev;struct device *dev;
@@ -84,14 +94,7 @@ struct int3472_discrete_device {const struct int3472_sensor_config *sensor_config; -struct int3472_gpio_regulator { -/* SUPPLY_MAP_COUNT * 2 to make room for second sensor mappings */ -struct regulator_consumer_supply supply_map[GPIO_REGULATOR_SUPPLY_MAP_COUNT *2 ]; -char supply_name_upper[GPIO_SUPPPLY_NAME_LENGTH ]; -char regulator_name[GPIO_REGULATOR_NAME_LENGTH ]; -struct regulator_dev *rdev; -struct regulator_desc rdesc; - } regulator; +struct int3472_gpio_regulator regulators[INT3472_MAX_REGULATORS ];struct int3472_clock {struct clk *clk;
@@ -113,6 +116,7 @@ struct int3472_discrete_device {unsigned int ngpios;/* how many GPIOs have we seen */ unsigned int n_sensor_gpios;/* how many have we mapped to sensor */ +unsigned int n_regulators;/* how many have we mapped to a regulator */ struct gpiod_lookup_table gpios; };
Signature · 1 line
2.49.0
PATCH 7/8 platform/x86: int3472: Add handshake pin support
In reply to Hans de GoedeNew Intel Meteor Lake based laptops with IPU6 cameras have a new type 0x12 pin defined in the INT3472 sensor companion device which describes the sensor's GPIOs.
This pin is primarily used on designs with a Lattice FPGA chip which is capable of running the sensor independently of the main CPU for features like presence detection. This pin needs to be driven high to make the FPGA run the power-on sequence of the sensor. After driving the pin high the FPGA "firmware" needs 25ms to comlpete the power-on sequence.
Add support for this modelling the handshake pin as a GPIO driven "dvdd" regulator with a 25 ms enable time. This model was chosen because:
1. Sensor chips don't have a handshake pin, so we need to abstract this in some way which does not require modification to the sensor drivers, sensor drivers using the bulk-regulator API to get avdd + vddio + dvdd is normal. So this will work to get the right value set to the handshake pin without requiring sensor driver modifications.
2. Sensors typically wait only a small time for the sensor to power-on after de-asserting reset. Not the 25ms the Lattice chip requires. Using the regulator framework's enable_time allows hiding the need for this delay from the sensor drivers.
--- .../x86/intel/int3472/clk_and_regulator.c | 2 ++ drivers/platform/x86/intel/int3472/common.h | 2 ++ drivers/platform/x86/intel/int3472/discrete.c | 16 +++++++++++++++- 3 files changed, 19 insertions(+), 1 deletion(-)
drivers/platform/x86/intel/int3472/clk_and_regulator.c +2 -0
@@ -187,6 +187,7 @@ void skl_int3472_unregister_clock(struct int3472_discrete_device *int3472)int skl_int3472_register_regulator (struct int3472_discrete_device *int3472,struct gpio_desc *gpio, +unsigned int enable_time,const char *supply_name,const char *second_sensor) {
@@ -223,6 +224,7 @@ int skl_int3472_register_regulator(struct int3472_discrete_device *int3472, } init_data.constraints.valid_ops_mask =REGULATOR_CHANGE_STATUS ; + init_data.constraints.enable_time = enable_time; init_data.consumer_supplies = regulator->supply_map; init_data.num_consumer_supplies = j;
drivers/platform/x86/intel/int3472/common.h +2 -0
@@ -22,6 +22,7 @@#define INT3472_GPIO_TYPE_POWER_ENABLE 0x0b#define INT3472_GPIO_TYPE_CLK_ENABLE 0x0c#define INT3472_GPIO_TYPE_PRIVACY_LED 0x0d +#define INT3472_GPIO_TYPE_HANDSHAKE 0x12#define INT3472_PDEV_MAX_NAME_LEN 23#define INT3472_MAX_SENSOR_GPIOS 3
@@ -136,6 +137,7 @@ void skl_int3472_unregister_clock(struct int3472_discrete_device *int3472);int skl_int3472_register_regulator (struct int3472_discrete_device *int3472,struct gpio_desc *gpio, +unsigned int enable_time,const char *supply_name,const char *second_sensor);void skl_int3472_unregister_regulator (struct int3472_discrete_device *int3472);
drivers/platform/x86/intel/int3472/discrete.c +15 -1
@@ -191,6 +191,10 @@ static void int3472_get_con_id_and_polarity(struct acpi_device *adev, u8 *type, *con_id ="avdd" ; *gpio_flags =GPIO_ACTIVE_HIGH ;break ; +case INT3472_GPIO_TYPE_HANDSHAKE : + *con_id ="dvdd" ; + *gpio_flags =GPIO_ACTIVE_HIGH ; +break ;default : *con_id ="unknown" ; *gpio_flags =GPIO_ACTIVE_HIGH ;
@@ -290,6 +294,7 @@ static int skl_int3472_handle_gpio_resources(struct acpi_resource *ares,case INT3472_GPIO_TYPE_CLK_ENABLE :case INT3472_GPIO_TYPE_PRIVACY_LED :case INT3472_GPIO_TYPE_POWER_ENABLE : +case INT3472_GPIO_TYPE_HANDSHAKE : gpio =skl_int3472_gpiod_get_from_temp_lookup (int3472, agpio, con_id, gpio_flags);if (IS_ERR (gpio)) { ret =PTR_ERR (gpio);
@@ -311,11 +316,20 @@ static int skl_int3472_handle_gpio_resources(struct acpi_resource *ares,break ;case INT3472_GPIO_TYPE_POWER_ENABLE : - ret =skl_int3472_register_regulator (int3472, gpio, con_id, + ret =skl_int3472_register_regulator (int3472, gpio,0 , con_id, int3472->quirks.avdd_second_sensor);if (ret) err_msg ="Failed to map regulator to sensor\n" ; +break ; +case INT3472_GPIO_TYPE_HANDSHAKE : +/* Setups using a handshake pin need 25 ms delay */ + ret =skl_int3472_register_regulator (int3472, gpio, +25 *USEC_PER_MSEC , + con_id,NULL ); +if (ret) + err_msg ="Failed to map regulator to sensor\n" ; +break ;default :/* Never reached */ ret = -EINVAL ;
Signature · 1 line
2.49.0
PATCH 8/8 platform/x86: int3472: Debug log when remapping pins
In reply to Hans de GoedeDebug log when remapping a pin/function because of a int3472_gpio_map[] match.
--- drivers/platform/x86/intel/int3472/discrete.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-)
drivers/platform/x86/intel/int3472/discrete.c +6 -2
@@ -146,9 +146,10 @@ static const struct int3472_gpio_map int3472_gpio_map[] = { { "INT347E", INT3472_GPIO_TYPE_RESET, INT3472_GPIO_TYPE_RESET, false, "enable" }, }; -static void int3472_get_con_id_and_polarity (struct acpi_device *adev,u8 *type, +static void int3472_get_con_id_and_polarity (struct int3472_discrete_device *int3472,u8 *type,const char **con_id,unsigned long *gpio_flags) { +struct acpi_device *adev = int3472->sensor;unsigned int i;for (i =0 ; i <ARRAY_SIZE (int3472_gpio_map); i++) {
@@ -163,6 +164,9 @@ static void int3472_get_con_id_and_polarity(struct acpi_device *adev, u8 *type,if (!acpi_dev_hid_uid_match (adev, int3472_gpio_map[i].hid,NULL ))continue ; +dev_dbg (int3472->dev,"mapping type 0x%02x pin to 0x%02x %s\n" , + *type, int3472_gpio_map[i].type_to, int3472_gpio_map[i].con_id); + *type = int3472_gpio_map[i].type_to; *gpio_flags = int3472_gpio_map[i].polarity_low ?GPIO_ACTIVE_LOW :GPIO_ACTIVE_HIGH ;
@@ -267,7 +271,7 @@ static int skl_int3472_handle_gpio_resources(struct acpi_resource *ares, type =FIELD_GET (INT3472_GPIO_DSM_TYPE , obj->integer.value); -int3472_get_con_id_and_polarity (int3472->sensor, &type, &con_id, &gpio_flags); +int3472_get_con_id_and_polarity (int3472, &type, &con_id, &gpio_flags); pin =FIELD_GET (INT3472_GPIO_DSM_PIN , obj->integer.value);/* Pin field is not really used under Windows and wraps around at 8 bits */
Signature · 1 line
2.49.0