dt-bindings: timer: Convert ti,keystone-timer to DT schema
Subsystems (2)
Rob Herring (Arm)
maintainerPATCH 1/1 dt-bindings: timer: Convert ti,keystone-timer to DT schema
Convert the TI Keystone Timer binding to DT schema format. It's a straight-forward conversion.
Signed-off-by Rob Herring (Arm) <[email protected]>
--- .../bindings/timer/ti,keystone-timer.txt | 29 --------- .../bindings/timer/ti,keystone-timer.yaml | 63 +++++++++++++++++++ 2 files changed, 63 insertions(+), 29 deletions(-) delete mode 100644 Documentation/devicetree/bindings/timer/ti,keystone-timer.txt create mode 100644 Documentation/devicetree/bindings/timer/ti,keystone-timer.yaml
Documentation/devicetree/bindings/timer/ti,keystone-timer.txt deleted +0 -29
@@ -1,29 +0,0 @@ -* Device tree bindings for Texas instruments Keystone timer - -This document provides bindings for the 64-bit timer in the KeyStone -architecture devices. The timer can be configured as a general-purpose 64-bit -timer, dual general-purpose 32-bit timers. When configured as dual 32-bit -timers, each half can operate in conjunction (chain mode) or independently -(unchained mode) of each other. - -It is global timer is a free running up-counter and can generate interrupt -when the counter reaches preset counter values. - -Documentation: -https://www.ti.com/lit/ug/sprugv5a/sprugv5a.pdf - -Required properties: - -- compatible : should be "ti,keystone-timer". -- reg : specifies base physical address and count of the registers. -- interrupts : interrupt generated by the timer. -- clocks : the clock feeding the timer clock. - -Example: - -timer@22f0000 { - compatible = "ti,keystone-timer"; - reg = <0x022f0000 0x80>; - interrupts = <GIC_SPI 110 IRQ_TYPE_EDGE_RISING>; - clocks = <&clktimer15>; -};
Documentation/devicetree/bindings/timer/ti,keystone-timer.yaml new file +63 -0
63 lines not on this page · raw message
Signature · 1 line
2.47.2
Daniel Lezcano
AppliedQuoted 5 lines · Rob Herring
Convert the TI Keystone Timer binding to DT schema format. It's a straight-forward conversion.
Signed-off-by Rob Herring (Arm) <[email protected]>---
Applied, thanks
Signature · 5 lines
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook | <http://twitter.com/#!/linaroorg> Twitter | <http://www.linaro.org/linaro-blog/> Blog
The following commit has been merged into the timers/clocksource branch of tip:
The following commit has been merged into the timers/clocksource branch of tip:
Commit-ID: 4d54b0b401f4ba97cbd0d65ddfe3dda2576a2500 Gitweb: https://git.kernel.org/tip/4d54b0b401f4ba97cbd0d65ddfe3dda2576a2500 Author: Rob Herring (Arm) <[email protected]> AuthorDate: Mon, 05 May 2025 21:23:29 -05:00 Committer: Daniel Lezcano <[email protected]> CommitterDate: Fri, 16 May 2025 11:10:34 +02:00
dt-bindings: timer: Convert ti,keystone-timer to DT schema
Convert the TI Keystone Timer binding to DT schema format. It's a straight-forward conversion.
Signed-off-by Rob Herring (Arm) <[email protected]>
Signed-off-by Daniel Lezcano <[email protected]>
--- Documentation/devicetree/bindings/timer/ti,keystone-timer.txt | 29 +--- Documentation/devicetree/bindings/timer/ti,keystone-timer.yaml | 63 +++++++- 2 files changed, 63 insertions(+), 29 deletions(-) delete mode 100644 Documentation/devicetree/bindings/timer/ti,keystone-timer.txt create mode 100644 Documentation/devicetree/bindings/timer/ti,keystone-timer.yaml
Documentation/devicetree/bindings/timer/ti,keystone-timer.txt deleted +0 -29
@@ -1,29 +0,0 @@ -* Device tree bindings for Texas instruments Keystone timer - -This document provides bindings for the 64-bit timer in the KeyStone -architecture devices. The timer can be configured as a general-purpose 64-bit -timer, dual general-purpose 32-bit timers. When configured as dual 32-bit -timers, each half can operate in conjunction (chain mode) or independently -(unchained mode) of each other. - -It is global timer is a free running up-counter and can generate interrupt -when the counter reaches preset counter values. - -Documentation: -https://www.ti.com/lit/ug/sprugv5a/sprugv5a.pdf - -Required properties: - -- compatible : should be "ti,keystone-timer". -- reg : specifies base physical address and count of the registers. -- interrupts : interrupt generated by the timer. -- clocks : the clock feeding the timer clock. - -Example: - -timer@22f0000 { - compatible = "ti,keystone-timer"; - reg = <0x022f0000 0x80>; - interrupts = <GIC_SPI 110 IRQ_TYPE_EDGE_RISING>; - clocks = <&clktimer15>; -};
Documentation/devicetree/bindings/timer/ti,keystone-timer.yaml new file +63 -0
63 lines not on this page · raw message