Skip to contentSkip to conversation

dt-bindings: serial: Convert microchip,pic32mzda-uart to DT schema

PATCH In review Rob Herring (Arm) 2 participants 2 messages May 7, 2025 – May 8, 2025

Subsystems (2)
lore
Share & tools
lore

Rob Herring (Arm)

author maintainer
#0 lore raw

PATCH v2 1/1 dt-bindings: serial: Convert microchip,pic32mzda-uart to DT schema

Convert the Microchip PIC32 UART binding to DT schema. The binding was unclear there are 3 interrupts. The functions were determined from the driver. The 'cts-gpios' property is covered by serial.yaml schema.

---
v2:
- Fix $id path and serial.yaml path

---
 .../bindings/serial/microchip,pic32-uart.txt  | 29 ----------
 .../serial/microchip,pic32mzda-uart.yaml      | 53 +++++++++++++++++++
 2 files changed, 53 insertions(+), 29 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt
 create mode 100644 Documentation/devicetree/bindings/serial/microchip,pic32mzda-uart.yaml
Documentation/devicetree/bindings/serial/microchip,pic32-uart.txt deleted +0 -29
deleted file mode 100644
index c8dd440e9747..000000000000
@@ -1,29 +0,0 @@
-* Microchip Universal Asynchronous Receiver Transmitter (UART)
-
-Required properties:
-- compatible: Should be "microchip,pic32mzda-uart"
-- reg: Should contain registers location and length
-- interrupts: Should contain interrupt
-- clocks: Phandle to the clock.
-          See: Documentation/devicetree/bindings/clock/clock-bindings.txt
-- pinctrl-names: A pinctrl state names "default" must be defined.
-- pinctrl-0: Phandle referencing pin configuration of the UART peripheral.
-             See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
-
-Optional properties:
-- cts-gpios: CTS pin for UART
-
-Example:
-	uart1: serial@1f822000 {
-		compatible = "microchip,pic32mzda-uart";
-		reg = <0x1f822000 0x50>;
-		interrupts = <112 IRQ_TYPE_LEVEL_HIGH>,
-			<113 IRQ_TYPE_LEVEL_HIGH>,
-			<114 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&rootclk PB2CLK>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_uart1
-				&pinctrl_uart1_cts
-				&pinctrl_uart1_rts>;
-		cts-gpios = <&gpio1 15 0>;
-	};
Documentation/devicetree/bindings/serial/microchip,pic32mzda-uart.yaml new file +53 -0

53 lines not on this page · raw message

Signature · 1 line
2.47.2
Reviewed-by on v2 1/1
#1 lore raw
Quoted 5 lines · Rob Herring (Arm)

Convert the Microchip PIC32 UART binding to DT schema. The binding was unclear there are 3 interrupts. The functions were determined from the driver. The 'cts-gpios' property is covered by serial.yaml schema.

Although...

Quoted 7 lines
Documentation/devicetree/bindings/serial/microchip,pic32mzda-uart.yaml new file +1 -0
new file mode 100644
index 000000000000..b176fd5b580e
@@ -0,0 +1,53 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)

Documentation/devicetree/bindings/serial/microchip,pic32mzda-uart.yaml line 11

Quoted 10 lines
Documentation/devicetree/bindings/serial/microchip,pic32mzda-uart.yaml new file +10 -0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/serial/microchip,pic32mzda-uart.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Microchip PIC32 UART
+
+maintainers:
+  - Andrei Pistirica <[email protected]>
+  - Purna Chandra Mandal <[email protected]>

I don't think either of these people still work for Microchip. (I don't have any idea actually who works on this device)