Skip to contentSkip to conversation

Support RK3528 variant of Rockchip naneng-combphy

PATCH Superseded Yao Zi 5 participants 16 messages May 19, 2025 – May 21, 2025

Subsystems (3)

v3 of 5 Superseded Latest is v5 →

lore
Share & tools
lore

Yao Zi

author
#0 lore raw

v3 cover Support RK3528 variant of Rockchip naneng-combphy

Rockchip RK3528 ships a naneng-combphy that operates in either PCIe or USB 3.0 mode. It has a similar control logic to previous generations of naneng-combphy but an apparently different register layout.

This series prepares phy-rockchip-naneng-combphy.c for variants with a different register layout and add RK3528 support.

Testing is done on both Radxa E20C and Radxa Rock 2A with downstream devicetree changes, both USB 3 and PCIe modes are verified with mainline driver and achives a reasonable link speed.

- Changed from v2
- phy binding patch
- Fix format issue
- drop review tags
- Link to v2: https://lore.kernel.org/all/[email protected]/
- Changed from v1
- Collect review tags
- Restyle RK3528 register definitions in the combphy driver
- Drop unused include of phy.h in SoC devicetree
- Link to v1: https://lore.kernel.org/all/[email protected]/

Yao Zi (5):
dt-bindings: soc: rockchip: Add RK3528 pipe-phy GRF syscon
dt-bindings: phy: rockchip: naneng-combphy: Add RK3528 variant
phy: rockchip: naneng-combphy: Add SoC prefix to register definitions
phy: rockchip: naneng-combphy: Add RK3528 support
arm64: dts: rockchip: Add naneng-combphy for RK3528

 .../phy/phy-rockchip-naneng-combphy.yaml      |   5 +-
 .../devicetree/bindings/soc/rockchip/grf.yaml |   1 +
 arch/arm64/boot/dts/rockchip/rk3528.dtsi      |  22 +
 .../rockchip/phy-rockchip-naneng-combphy.c    | 746 +++++++++++-------
 4 files changed, 500 insertions(+), 274 deletions(-)
Signature · 1 line
2.49.0
author
#1 lore raw

PATCH v3 1/5 dt-bindings: soc: rockchip: Add RK3528 pipe-phy GRF syscon

Add compatible string for pipe-phy GRF found on RK3528 SoC, which controls misc settings for the integrated naneng-combphy.

---
 Documentation/devicetree/bindings/soc/rockchip/grf.yaml | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/soc/rockchip/grf.yaml +1 -0
index 8cbf5b6772dd..268f72b047d8 100644
@@ -16,6 +16,7 @@ properties:
           - enum:
               - rockchip,rk3288-sgrf
               - rockchip,rk3528-ioc-grf
+              - rockchip,rk3528-pipe-phy-grf
               - rockchip,rk3528-vo-grf
               - rockchip,rk3528-vpu-grf
               - rockchip,rk3562-ioc-grf
Signature · 1 line
2.49.0
author
#2 lore raw

PATCH v3 2/5 dt-bindings: phy: rockchip: naneng-combphy: Add RK3528 variant

In reply to Yao Zi

Rockchip RK3528 ships one naneng-combphy which operates in either PCIe or USB 3 mode. Document its compatible string.

---
 .../devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml +4 -1
index 888e6b2aac5a..969d7b1850d6 100644
@@ -12,6 +12,7 @@ maintainers:
 properties:
   compatible:
     enum:
+      - rockchip,rk3528-naneng-combphy
       - rockchip,rk3562-naneng-combphy
       - rockchip,rk3568-naneng-combphy
       - rockchip,rk3576-naneng-combphy
@@ -102,7 +103,9 @@ allOf:
       properties:
         compatible:
           contains:
-            const: rockchip,rk3588-naneng-combphy
+            enum:
+              - rockchip,rk3528-naneng-combphy
+              - rockchip,rk3588-naneng-combphy
     then:
       properties:
         resets:
Signature · 1 line
2.49.0
Acked-by on v3 2/5
#3 lore raw

Re: [PATCH v3 2/5] dt-bindings: phy: rockchip: naneng-combphy: Add RK3528 variant

Quoted 4 lines · Yao Zi

Rockchip RK3528 ships one naneng-combphy which operates in either PCIe or USB 3 mode. Document its compatible string.

Quoted 30 lines
---
 .../devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml +4 -1
index 888e6b2aac5a..969d7b1850d6 100644
@@ -12,6 +12,7 @@ maintainers:
 properties:
   compatible:
     enum:
+      - rockchip,rk3528-naneng-combphy
       - rockchip,rk3562-naneng-combphy
       - rockchip,rk3568-naneng-combphy
       - rockchip,rk3576-naneng-combphy
@@ -102,7 +103,9 @@ allOf:
       properties:
         compatible:
           contains:
-            const: rockchip,rk3588-naneng-combphy
+            enum:
+              - rockchip,rk3528-naneng-combphy
+              - rockchip,rk3588-naneng-combphy
     then:
       properties:
         resets:
Signature · 1 line
2.49.0
author
#4 lore raw

PATCH v3 3/5 phy: rockchip: naneng-combphy: Add SoC prefix to register definitions

In reply to Yao Zi

All supported variants of naneng-combphy follow a register layout similar to the RK3568 variant with some exceptions of SoC-specific registers.

Add RK3568 prefix for the common set of registers and the corresponding SoC prefix for SoC-specific registers, making usage of definitions clear and preparing for future COMBPHY variants with a different register layout.

---
 .../rockchip/phy-rockchip-naneng-combphy.c    | 560 +++++++++---------
 1 file changed, 288 insertions(+), 272 deletions(-)
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +288 -272
index ce91fb1d5167..1d1c7723584b 100644
@@ -21,78 +21,80 @@
 #define REF_CLOCK_100MHz		(100 * HZ_PER_MHZ)
 
 /* COMBO PHY REG */
-#define PHYREG6				0x14
-#define PHYREG6_PLL_DIV_MASK		GENMASK(7, 6)
-#define PHYREG6_PLL_DIV_SHIFT		6
-#define PHYREG6_PLL_DIV_2		1
-
-#define PHYREG7				0x18
-#define PHYREG7_TX_RTERM_MASK		GENMASK(7, 4)
-#define PHYREG7_TX_RTERM_SHIFT		4
-#define PHYREG7_TX_RTERM_50OHM		8
-#define PHYREG7_RX_RTERM_MASK		GENMASK(3, 0)
-#define PHYREG7_RX_RTERM_SHIFT		0
-#define PHYREG7_RX_RTERM_44OHM		15
-
-#define PHYREG8				0x1C
-#define PHYREG8_SSC_EN			BIT(4)
-
-#define PHYREG10			0x24
-#define PHYREG10_SSC_PCM_MASK		GENMASK(3, 0)
-#define PHYREG10_SSC_PCM_3500PPM	7
-
-#define PHYREG11			0x28
-#define PHYREG11_SU_TRIM_0_7		0xF0
-
-#define PHYREG12			0x2C
-#define PHYREG12_PLL_LPF_ADJ_VALUE	4
-
-#define PHYREG13			0x30
-#define PHYREG13_RESISTER_MASK		GENMASK(5, 4)
-#define PHYREG13_RESISTER_SHIFT		0x4
-#define PHYREG13_RESISTER_HIGH_Z	3
-#define PHYREG13_CKRCV_AMP0		BIT(7)
-
-#define PHYREG14			0x34
-#define PHYREG14_CKRCV_AMP1		BIT(0)
-
-#define PHYREG15			0x38
-#define PHYREG15_CTLE_EN		BIT(0)
-#define PHYREG15_SSC_CNT_MASK		GENMASK(7, 6)
-#define PHYREG15_SSC_CNT_SHIFT		6
-#define PHYREG15_SSC_CNT_VALUE		1
-
-#define PHYREG16			0x3C
-#define PHYREG16_SSC_CNT_VALUE		0x5f
-
-#define PHYREG17			0x40
-
-#define PHYREG18			0x44
-#define PHYREG18_PLL_LOOP		0x32
-
-#define PHYREG21			0x50
-#define PHYREG21_RX_SQUELCH_VAL		0x0D
-
-#define PHYREG27			0x6C
-#define PHYREG27_RX_TRIM_RK3588		0x4C
-
-#define PHYREG30			0x74
-
-#define PHYREG32			0x7C
-#define PHYREG32_SSC_MASK		GENMASK(7, 4)
-#define PHYREG32_SSC_DIR_MASK		GENMASK(5, 4)
-#define PHYREG32_SSC_DIR_SHIFT		4
-#define PHYREG32_SSC_UPWARD		0
-#define PHYREG32_SSC_DOWNWARD		1
-#define PHYREG32_SSC_OFFSET_MASK	GENMASK(7, 6)
-#define PHYREG32_SSC_OFFSET_SHIFT	6
-#define PHYREG32_SSC_OFFSET_500PPM	1
-
-#define PHYREG33			0x80
-#define PHYREG33_PLL_KVCO_MASK		GENMASK(4, 2)
-#define PHYREG33_PLL_KVCO_SHIFT		2
-#define PHYREG33_PLL_KVCO_VALUE		2
-#define PHYREG33_PLL_KVCO_VALUE_RK3576	4
+#define RK3568_PHYREG6				0x14
+#define RK3568_PHYREG6_PLL_DIV_MASK		GENMASK(7, 6)
+#define RK3568_PHYREG6_PLL_DIV_SHIFT		6
+#define RK3568_PHYREG6_PLL_DIV_2		1
+
+#define RK3568_PHYREG7				0x18
+#define RK3568_PHYREG7_TX_RTERM_MASK		GENMASK(7, 4)
+#define RK3568_PHYREG7_TX_RTERM_SHIFT		4
+#define RK3568_PHYREG7_TX_RTERM_50OHM		8
+#define RK3568_PHYREG7_RX_RTERM_MASK		GENMASK(3, 0)
+#define RK3568_PHYREG7_RX_RTERM_SHIFT		0
+#define RK3568_PHYREG7_RX_RTERM_44OHM		15
+
+#define RK3568_PHYREG8				0x1C
+#define RK3568_PHYREG8_SSC_EN			BIT(4)
+
+#define RK3568_PHYREG11				0x28
+#define RK3568_PHYREG11_SU_TRIM_0_7		0xF0
+
+#define RK3568_PHYREG12				0x2C
+#define RK3568_PHYREG12_PLL_LPF_ADJ_VALUE	4
+
+#define RK3568_PHYREG13				0x30
+#define RK3568_PHYREG13_RESISTER_MASK		GENMASK(5, 4)
+#define RK3568_PHYREG13_RESISTER_SHIFT		0x4
+#define RK3568_PHYREG13_RESISTER_HIGH_Z		3
+#define RK3568_PHYREG13_CKRCV_AMP0		BIT(7)
+
+#define RK3568_PHYREG14				0x34
+#define RK3568_PHYREG14_CKRCV_AMP1		BIT(0)
+
+#define RK3568_PHYREG15				0x38
+#define RK3568_PHYREG15_CTLE_EN			BIT(0)
+#define RK3568_PHYREG15_SSC_CNT_MASK		GENMASK(7, 6)
+#define RK3568_PHYREG15_SSC_CNT_SHIFT		6
+#define RK3568_PHYREG15_SSC_CNT_VALUE		1
+
+#define RK3568_PHYREG16				0x3C
+#define RK3568_PHYREG16_SSC_CNT_VALUE		0x5f
+
+#define RK3568_PHYREG18				0x44
+#define RK3568_PHYREG18_PLL_LOOP		0x32
+
+#define RK3568_PHYREG32				0x7C
+#define RK3568_PHYREG32_SSC_MASK		GENMASK(7, 4)
+#define RK3568_PHYREG32_SSC_DIR_MASK		GENMASK(5, 4)
+#define RK3568_PHYREG32_SSC_DIR_SHIFT		4
+#define RK3568_PHYREG32_SSC_UPWARD		0
+#define RK3568_PHYREG32_SSC_DOWNWARD		1
+#define RK3568_PHYREG32_SSC_OFFSET_MASK	GENMASK(7, 6)
+#define RK3568_PHYREG32_SSC_OFFSET_SHIFT	6
+#define RK3568_PHYREG32_SSC_OFFSET_500PPM	1
+
+#define RK3568_PHYREG33				0x80
+#define RK3568_PHYREG33_PLL_KVCO_MASK		GENMASK(4, 2)
+#define RK3568_PHYREG33_PLL_KVCO_SHIFT		2
+#define RK3568_PHYREG33_PLL_KVCO_VALUE		2
+#define RK3576_PHYREG33_PLL_KVCO_VALUE		4
+
+/* RK3588 COMBO PHY registers */
+#define RK3588_PHYREG27				0x6C
+#define RK3588_PHYREG27_RX_TRIM			0x4C
+
+/* RK3576 COMBO PHY registers */
+#define RK3576_PHYREG10				0x24
+#define RK3576_PHYREG10_SSC_PCM_MASK		GENMASK(3, 0)
+#define RK3576_PHYREG10_SSC_PCM_3500PPM		7
+
+#define RK3576_PHYREG17				0x40
+
+#define RK3576_PHYREG21				0x50
+#define RK3576_PHYREG21_RX_SQUELCH_VAL		0x0D
+
+#define RK3576_PHYREG30				0x74
 
 struct rockchip_combphy_priv;
 
@@ -405,9 +407,8 @@ static int rk3562_combphy_cfg(struct rockchip_combphy_priv *priv)
 	switch (priv->type) {
 	case PHY_TYPE_PCIE:
 		/* Set SSC downward spread spectrum */
-		rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK,
-					 PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT,
-					 PHYREG32);
+		val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
+		rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
 
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
@@ -416,29 +417,30 @@ static int rk3562_combphy_cfg(struct rockchip_combphy_priv *priv)
 		break;
 	case PHY_TYPE_USB3:
 		/* Set SSC downward spread spectrum */
-		rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK,
-					 PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT,
-					 PHYREG32);
+		val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
+		rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val,
+					 RK3568_PHYREG32);
 
 		/* Enable adaptive CTLE for USB3.0 Rx */
-		rockchip_combphy_updatel(priv, PHYREG15_CTLE_EN,
-					 PHYREG15_CTLE_EN, PHYREG15);
+		rockchip_combphy_updatel(priv, RK3568_PHYREG15_CTLE_EN,
+					 RK3568_PHYREG15_CTLE_EN, RK3568_PHYREG15);
 
 		/* Set PLL KVCO fine tuning signals */
-		rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK, BIT(3), PHYREG33);
+		rockchip_combphy_updatel(priv, RK3568_PHYREG33_PLL_KVCO_MASK,
+					 BIT(3), RK3568_PHYREG33);
 
 		/* Set PLL LPF R1 to su_trim[10:7]=1001 */
-		writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12);
+		writel(RK3568_PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + RK3568_PHYREG12);
 
 		/* Set PLL input clock divider 1/2 */
-		val = FIELD_PREP(PHYREG6_PLL_DIV_MASK, PHYREG6_PLL_DIV_2);
-		rockchip_combphy_updatel(priv, PHYREG6_PLL_DIV_MASK, val, PHYREG6);
+		val = FIELD_PREP(RK3568_PHYREG6_PLL_DIV_MASK, RK3568_PHYREG6_PLL_DIV_2);
+		rockchip_combphy_updatel(priv, RK3568_PHYREG6_PLL_DIV_MASK, val, RK3568_PHYREG6);
 
 		/* Set PLL loop divider */
-		writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18);
+		writel(RK3568_PHYREG18_PLL_LOOP, priv->mmio + RK3568_PHYREG18);
 
 		/* Set PLL KVCO to min and set PLL charge pump current to max */
-		writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11);
+		writel(RK3568_PHYREG11_SU_TRIM_0_7, priv->mmio + RK3568_PHYREG11);
 
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_sel_usb, true);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false);
@@ -456,11 +458,12 @@ static int rk3562_combphy_cfg(struct rockchip_combphy_priv *priv)
 	case REF_CLOCK_24MHz:
 		if (priv->type == PHY_TYPE_USB3) {
 			/* Set ssc_cnt[9:0]=0101111101 & 31.5KHz */
-			val = FIELD_PREP(PHYREG15_SSC_CNT_MASK, PHYREG15_SSC_CNT_VALUE);
-			rockchip_combphy_updatel(priv, PHYREG15_SSC_CNT_MASK,
-						 val, PHYREG15);
+			val = FIELD_PREP(RK3568_PHYREG15_SSC_CNT_MASK,
+					 RK3568_PHYREG15_SSC_CNT_VALUE);
+			rockchip_combphy_updatel(priv, RK3568_PHYREG15_SSC_CNT_MASK,
+						 val, RK3568_PHYREG15);
 
-			writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
+			writel(RK3568_PHYREG16_SSC_CNT_VALUE, priv->mmio + RK3568_PHYREG16);
 		}
 		break;
 	case REF_CLOCK_25MHz:
@@ -470,19 +473,20 @@ static int rk3562_combphy_cfg(struct rockchip_combphy_priv *priv)
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_100m, true);
 		if (priv->type == PHY_TYPE_PCIE) {
 			/* PLL KVCO tuning fine */
-			val = FIELD_PREP(PHYREG33_PLL_KVCO_MASK, PHYREG33_PLL_KVCO_VALUE);
-			rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
-						 val, PHYREG33);
+			val = FIELD_PREP(RK3568_PHYREG33_PLL_KVCO_MASK,
+					 RK3568_PHYREG33_PLL_KVCO_VALUE);
+			rockchip_combphy_updatel(priv, RK3568_PHYREG33_PLL_KVCO_MASK,
+						 val, RK3568_PHYREG33);
 
 			/* Enable controlling random jitter, aka RMJ */
-			writel(0x4, priv->mmio + PHYREG12);
+			writel(0x4, priv->mmio + RK3568_PHYREG12);
 
-			val = PHYREG6_PLL_DIV_2 << PHYREG6_PLL_DIV_SHIFT;
-			rockchip_combphy_updatel(priv, PHYREG6_PLL_DIV_MASK,
-						 val, PHYREG6);
+			val = RK3568_PHYREG6_PLL_DIV_2 << RK3568_PHYREG6_PLL_DIV_SHIFT;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG6_PLL_DIV_MASK,
+						 val, RK3568_PHYREG6);
 
-			writel(0x32, priv->mmio + PHYREG18);
-			writel(0xf0, priv->mmio + PHYREG11);
+			writel(0x32, priv->mmio + RK3568_PHYREG18);
+			writel(0xf0, priv->mmio + RK3568_PHYREG11);
 		}
 		break;
 	default:
@@ -493,20 +497,21 @@ static int rk3562_combphy_cfg(struct rockchip_combphy_priv *priv)
 	if (priv->ext_refclk) {
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_ext, true);
 		if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) {
-			val = PHYREG13_RESISTER_HIGH_Z << PHYREG13_RESISTER_SHIFT;
-			val |= PHYREG13_CKRCV_AMP0;
-			rockchip_combphy_updatel(priv, PHYREG13_RESISTER_MASK, val, PHYREG13);
-
-			val = readl(priv->mmio + PHYREG14);
-			val |= PHYREG14_CKRCV_AMP1;
-			writel(val, priv->mmio + PHYREG14);
+			val = RK3568_PHYREG13_RESISTER_HIGH_Z << RK3568_PHYREG13_RESISTER_SHIFT;
+			val |= RK3568_PHYREG13_CKRCV_AMP0;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG13_RESISTER_MASK, val,
+						 RK3568_PHYREG13);
+
+			val = readl(priv->mmio + RK3568_PHYREG14);
+			val |= RK3568_PHYREG14_CKRCV_AMP1;
+			writel(val, priv->mmio + RK3568_PHYREG14);
 		}
 	}
 
 	if (priv->enable_ssc) {
-		val = readl(priv->mmio + PHYREG8);
-		val |= PHYREG8_SSC_EN;
-		writel(val, priv->mmio + PHYREG8);
+		val = readl(priv->mmio + RK3568_PHYREG8);
+		val |= RK3568_PHYREG8_SSC_EN;
+		writel(val, priv->mmio + RK3568_PHYREG8);
 	}
 
 	return 0;
@@ -553,9 +558,9 @@ static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
 	switch (priv->type) {
 	case PHY_TYPE_PCIE:
 		/* Set SSC downward spread spectrum. */
-		rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK,
-					 PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT,
-					 PHYREG32);
+		val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
+
+		rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
 
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
@@ -565,30 +570,28 @@ static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
 
 	case PHY_TYPE_USB3:
 		/* Set SSC downward spread spectrum. */
-		rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK,
-					 PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT,
-					 PHYREG32);
+		val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT,
+		rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
 
 		/* Enable adaptive CTLE for USB3.0 Rx. */
-		val = readl(priv->mmio + PHYREG15);
-		val |= PHYREG15_CTLE_EN;
-		writel(val, priv->mmio + PHYREG15);
+		val = readl(priv->mmio + RK3568_PHYREG15);
+		val |= RK3568_PHYREG15_CTLE_EN;
+		writel(val, priv->mmio + RK3568_PHYREG15);
 
 		/* Set PLL KVCO fine tuning signals. */
-		rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
-					 PHYREG33_PLL_KVCO_VALUE << PHYREG33_PLL_KVCO_SHIFT,
-					 PHYREG33);
+		val = RK3568_PHYREG33_PLL_KVCO_VALUE << RK3568_PHYREG33_PLL_KVCO_SHIFT;
+		rockchip_combphy_updatel(priv, RK3568_PHYREG33_PLL_KVCO_MASK, val, RK3568_PHYREG33);
 
 		/* Enable controlling random jitter. */
-		writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12);
+		writel(RK3568_PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + RK3568_PHYREG12);
 
 		/* Set PLL input clock divider 1/2. */
-		rockchip_combphy_updatel(priv, PHYREG6_PLL_DIV_MASK,
-					 PHYREG6_PLL_DIV_2 << PHYREG6_PLL_DIV_SHIFT,
-					 PHYREG6);
+		rockchip_combphy_updatel(priv, RK3568_PHYREG6_PLL_DIV_MASK,
+					 RK3568_PHYREG6_PLL_DIV_2 << RK3568_PHYREG6_PLL_DIV_SHIFT,
+					 RK3568_PHYREG6);
 
-		writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18);
-		writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11);
+		writel(RK3568_PHYREG18_PLL_LOOP, priv->mmio + RK3568_PHYREG18);
+		writel(RK3568_PHYREG11_SU_TRIM_0_7, priv->mmio + RK3568_PHYREG11);
 
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_sel_usb, true);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false);
@@ -598,16 +601,16 @@ static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
 
 	case PHY_TYPE_SATA:
 		/* Enable adaptive CTLE for SATA Rx. */
-		val = readl(priv->mmio + PHYREG15);
-		val |= PHYREG15_CTLE_EN;
-		writel(val, priv->mmio + PHYREG15);
+		val = readl(priv->mmio + RK3568_PHYREG15);
+		val |= RK3568_PHYREG15_CTLE_EN;
+		writel(val, priv->mmio + RK3568_PHYREG15);
 		/*
 		 * Set tx_rterm=50ohm and rx_rterm=44ohm for SATA.
 		 * 0: 60ohm, 8: 50ohm 15: 44ohm (by step abort 1ohm)
 		 */
-		val = PHYREG7_TX_RTERM_50OHM << PHYREG7_TX_RTERM_SHIFT;
-		val |= PHYREG7_RX_RTERM_44OHM << PHYREG7_RX_RTERM_SHIFT;
-		writel(val, priv->mmio + PHYREG7);
+		val = RK3568_PHYREG7_TX_RTERM_50OHM << RK3568_PHYREG7_TX_RTERM_SHIFT;
+		val |= RK3568_PHYREG7_RX_RTERM_44OHM << RK3568_PHYREG7_RX_RTERM_SHIFT;
+		writel(val, priv->mmio + RK3568_PHYREG7);
 
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_sata, true);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_sata, true);
@@ -642,11 +645,11 @@ static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
 	case REF_CLOCK_24MHz:
 		if (priv->type == PHY_TYPE_USB3 || priv->type == PHY_TYPE_SATA) {
 			/* Set ssc_cnt[9:0]=0101111101 & 31.5KHz. */
-			val = PHYREG15_SSC_CNT_VALUE << PHYREG15_SSC_CNT_SHIFT;
-			rockchip_combphy_updatel(priv, PHYREG15_SSC_CNT_MASK,
-						 val, PHYREG15);
+			val = RK3568_PHYREG15_SSC_CNT_VALUE << RK3568_PHYREG15_SSC_CNT_SHIFT;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG15_SSC_CNT_MASK,
+						 val, RK3568_PHYREG15);
 
-			writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
+			writel(RK3568_PHYREG16_SSC_CNT_VALUE, priv->mmio + RK3568_PHYREG16);
 		}
 		break;
 
@@ -658,24 +661,26 @@ static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_100m, true);
 		if (priv->type == PHY_TYPE_PCIE) {
 			/* PLL KVCO  fine tuning. */
-			val = PHYREG33_PLL_KVCO_VALUE << PHYREG33_PLL_KVCO_SHIFT;
-			rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
-						 val, PHYREG33);
+			val = RK3568_PHYREG33_PLL_KVCO_VALUE << RK3568_PHYREG33_PLL_KVCO_SHIFT;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG33_PLL_KVCO_MASK,
+						 val, RK3568_PHYREG33);
 
 			/* Enable controlling random jitter. */
-			writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12);
+			writel(RK3568_PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + RK3568_PHYREG12);
 
-			val = PHYREG6_PLL_DIV_2 << PHYREG6_PLL_DIV_SHIFT;
-			rockchip_combphy_updatel(priv, PHYREG6_PLL_DIV_MASK,
-						 val, PHYREG6);
+			val = RK3568_PHYREG6_PLL_DIV_2 << RK3568_PHYREG6_PLL_DIV_SHIFT;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG6_PLL_DIV_MASK,
+						 val, RK3568_PHYREG6);
 
-			writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18);
-			writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11);
+			writel(RK3568_PHYREG18_PLL_LOOP, priv->mmio + RK3568_PHYREG18);
+			writel(RK3568_PHYREG11_SU_TRIM_0_7, priv->mmio + RK3568_PHYREG11);
 		} else if (priv->type == PHY_TYPE_SATA) {
 			/* downward spread spectrum +500ppm */
-			val = PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT;
-			val |= PHYREG32_SSC_OFFSET_500PPM << PHYREG32_SSC_OFFSET_SHIFT;
-			rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, val, PHYREG32);
+			val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
+			val |= RK3568_PHYREG32_SSC_OFFSET_500PPM <<
+			       RK3568_PHYREG32_SSC_OFFSET_SHIFT;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val,
+						 RK3568_PHYREG32);
 		}
 		break;
 
@@ -687,20 +692,21 @@ static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
 	if (priv->ext_refclk) {
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_ext, true);
 		if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) {
-			val = PHYREG13_RESISTER_HIGH_Z << PHYREG13_RESISTER_SHIFT;
-			val |= PHYREG13_CKRCV_AMP0;
-			rockchip_combphy_updatel(priv, PHYREG13_RESISTER_MASK, val, PHYREG13);
-
-			val = readl(priv->mmio + PHYREG14);
-			val |= PHYREG14_CKRCV_AMP1;
-			writel(val, priv->mmio + PHYREG14);
+			val = RK3568_PHYREG13_RESISTER_HIGH_Z << RK3568_PHYREG13_RESISTER_SHIFT;
+			val |= RK3568_PHYREG13_CKRCV_AMP0;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG13_RESISTER_MASK, val,
+						 RK3568_PHYREG13);
+
+			val = readl(priv->mmio + RK3568_PHYREG14);
+			val |= RK3568_PHYREG14_CKRCV_AMP1;
+			writel(val, priv->mmio + RK3568_PHYREG14);
 		}
 	}
 
 	if (priv->enable_ssc) {
-		val = readl(priv->mmio + PHYREG8);
-		val |= PHYREG8_SSC_EN;
-		writel(val, priv->mmio + PHYREG8);
+		val = readl(priv->mmio + RK3568_PHYREG8);
+		val |= RK3568_PHYREG8_SSC_EN;
+		writel(val, priv->mmio + RK3568_PHYREG8);
 	}
 
 	return 0;
@@ -759,8 +765,8 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
 	switch (priv->type) {
 	case PHY_TYPE_PCIE:
 		/* Set SSC downward spread spectrum */
-		val = FIELD_PREP(PHYREG32_SSC_MASK, PHYREG32_SSC_DOWNWARD);
-		rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, val, PHYREG32);
+		val = FIELD_PREP(RK3568_PHYREG32_SSC_MASK, RK3568_PHYREG32_SSC_DOWNWARD);
+		rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
 
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
@@ -770,32 +776,33 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
 
 	case PHY_TYPE_USB3:
 		/* Set SSC downward spread spectrum */
-		val = FIELD_PREP(PHYREG32_SSC_MASK, PHYREG32_SSC_DOWNWARD);
-		rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, val, PHYREG32);
+		val = FIELD_PREP(RK3568_PHYREG32_SSC_MASK, RK3568_PHYREG32_SSC_DOWNWARD);
+		rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
 
 		/* Enable adaptive CTLE for USB3.0 Rx */
-		val = readl(priv->mmio + PHYREG15);
-		val |= PHYREG15_CTLE_EN;
-		writel(val, priv->mmio + PHYREG15);
+		val = readl(priv->mmio + RK3568_PHYREG15);
+		val |= RK3568_PHYREG15_CTLE_EN;
+		writel(val, priv->mmio + RK3568_PHYREG15);
 
 		/* Set PLL KVCO fine tuning signals */
-		rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK, BIT(3), PHYREG33);
+		rockchip_combphy_updatel(priv, RK3568_PHYREG33_PLL_KVCO_MASK, BIT(3),
+					 RK3568_PHYREG33);
 
 		/* Set PLL LPF R1 to su_trim[10:7]=1001 */
-		writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12);
+		writel(RK3568_PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + RK3568_PHYREG12);
 
 		/* Set PLL input clock divider 1/2 */
-		val = FIELD_PREP(PHYREG6_PLL_DIV_MASK, PHYREG6_PLL_DIV_2);
-		rockchip_combphy_updatel(priv, PHYREG6_PLL_DIV_MASK, val, PHYREG6);
+		val = FIELD_PREP(RK3568_PHYREG6_PLL_DIV_MASK, RK3568_PHYREG6_PLL_DIV_2);
+		rockchip_combphy_updatel(priv, RK3568_PHYREG6_PLL_DIV_MASK, val, RK3568_PHYREG6);
 
 		/* Set PLL loop divider */
-		writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18);
+		writel(RK3568_PHYREG18_PLL_LOOP, priv->mmio + RK3568_PHYREG18);
 
 		/* Set PLL KVCO to min and set PLL charge pump current to max */
-		writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11);
+		writel(RK3568_PHYREG11_SU_TRIM_0_7, priv->mmio + RK3568_PHYREG11);
 
 		/* Set Rx squelch input filler bandwidth */
-		writel(PHYREG21_RX_SQUELCH_VAL, priv->mmio + PHYREG21);
+		writel(RK3576_PHYREG21_RX_SQUELCH_VAL, priv->mmio + RK3576_PHYREG21);
 
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txelec_sel, false);
@@ -804,14 +811,14 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
 
 	case PHY_TYPE_SATA:
 		/* Enable adaptive CTLE for SATA Rx */
-		val = readl(priv->mmio + PHYREG15);
-		val |= PHYREG15_CTLE_EN;
-		writel(val, priv->mmio + PHYREG15);
+		val = readl(priv->mmio + RK3568_PHYREG15);
+		val |= RK3568_PHYREG15_CTLE_EN;
+		writel(val, priv->mmio + RK3568_PHYREG15);
 
 		/* Set tx_rterm = 50 ohm and rx_rterm = 43.5 ohm */
-		val = PHYREG7_TX_RTERM_50OHM << PHYREG7_TX_RTERM_SHIFT;
-		val |= PHYREG7_RX_RTERM_44OHM << PHYREG7_RX_RTERM_SHIFT;
-		writel(val, priv->mmio + PHYREG7);
+		val = RK3568_PHYREG7_TX_RTERM_50OHM << RK3568_PHYREG7_TX_RTERM_SHIFT;
+		val |= RK3568_PHYREG7_RX_RTERM_44OHM << RK3568_PHYREG7_RX_RTERM_SHIFT;
+		writel(val, priv->mmio + RK3568_PHYREG7);
 
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_sata, true);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_sata, true);
@@ -833,19 +840,21 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_24m, true);
 		if (priv->type == PHY_TYPE_USB3 || priv->type == PHY_TYPE_SATA) {
 			/* Set ssc_cnt[9:0]=0101111101 & 31.5KHz */
-			val = FIELD_PREP(PHYREG15_SSC_CNT_MASK, PHYREG15_SSC_CNT_VALUE);
-			rockchip_combphy_updatel(priv, PHYREG15_SSC_CNT_MASK,
-						 val, PHYREG15);
+			val = FIELD_PREP(RK3568_PHYREG15_SSC_CNT_MASK,
+					 RK3568_PHYREG15_SSC_CNT_VALUE);
+			rockchip_combphy_updatel(priv, RK3568_PHYREG15_SSC_CNT_MASK,
+						 val, RK3568_PHYREG15);
 
-			writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
+			writel(RK3568_PHYREG16_SSC_CNT_VALUE, priv->mmio + RK3568_PHYREG16);
 		} else if (priv->type == PHY_TYPE_PCIE) {
 			/* PLL KVCO tuning fine */
-			val = FIELD_PREP(PHYREG33_PLL_KVCO_MASK, PHYREG33_PLL_KVCO_VALUE_RK3576);
-			rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
-						 val, PHYREG33);
+			val = FIELD_PREP(RK3568_PHYREG33_PLL_KVCO_MASK,
+					 RK3576_PHYREG33_PLL_KVCO_VALUE);
+			rockchip_combphy_updatel(priv, RK3568_PHYREG33_PLL_KVCO_MASK,
+						 val, RK3568_PHYREG33);
 
 			/* Set up rx_pck invert and rx msb to disable */
-			writel(0x00, priv->mmio + PHYREG27);
+			writel(0x00, priv->mmio + RK3588_PHYREG27);
 
 			/*
 			 * Set up SU adjust signal:
@@ -853,11 +862,11 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
 			 * su_trim[15:8],  PLL LPF R1 adujst bits[9:7]=3'b011
 			 * su_trim[31:24], CKDRV adjust
 			 */
-			writel(0x90, priv->mmio + PHYREG11);
-			writel(0x02, priv->mmio + PHYREG12);
-			writel(0x57, priv->mmio + PHYREG14);
+			writel(0x90, priv->mmio + RK3568_PHYREG11);
+			writel(0x02, priv->mmio + RK3568_PHYREG12);
+			writel(0x57, priv->mmio + RK3568_PHYREG14);
 
-			writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
+			writel(RK3568_PHYREG16_SSC_CNT_VALUE, priv->mmio + RK3568_PHYREG16);
 		}
 		break;
 
@@ -869,15 +878,16 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_100m, true);
 		if (priv->type == PHY_TYPE_PCIE) {
 			/* gate_tx_pck_sel length select work for L1SS */
-			writel(0xc0, priv->mmio + PHYREG30);
+			writel(0xc0, priv->mmio + RK3576_PHYREG30);
 
 			/* PLL KVCO tuning fine */
-			val = FIELD_PREP(PHYREG33_PLL_KVCO_MASK, PHYREG33_PLL_KVCO_VALUE_RK3576);
-			rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
-						 val, PHYREG33);
+			val = FIELD_PREP(RK3568_PHYREG33_PLL_KVCO_MASK,
+					 RK3576_PHYREG33_PLL_KVCO_VALUE);
+			rockchip_combphy_updatel(priv, RK3568_PHYREG33_PLL_KVCO_MASK,
+						 val, RK3568_PHYREG33);
 
 			/* Set up rx_trim: PLL LPF C1 85pf R1 1.25kohm */
-			writel(0x4c, priv->mmio + PHYREG27);
+			writel(0x4c, priv->mmio + RK3588_PHYREG27);
 
 			/*
 			 * Set up SU adjust signal:
@@ -887,20 +897,23 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
 			 * su_trim[23:16], CKRCV adjust
 			 * su_trim[31:24], CKDRV adjust
 			 */
-			writel(0x90, priv->mmio + PHYREG11);
-			writel(0x43, priv->mmio + PHYREG12);
-			writel(0x88, priv->mmio + PHYREG13);
-			writel(0x56, priv->mmio + PHYREG14);
+			writel(0x90, priv->mmio + RK3568_PHYREG11);
+			writel(0x43, priv->mmio + RK3568_PHYREG12);
+			writel(0x88, priv->mmio + RK3568_PHYREG13);
+			writel(0x56, priv->mmio + RK3568_PHYREG14);
 		} else if (priv->type == PHY_TYPE_SATA) {
 			/* downward spread spectrum +500ppm */
-			val = FIELD_PREP(PHYREG32_SSC_DIR_MASK, PHYREG32_SSC_DOWNWARD);
-			val |= FIELD_PREP(PHYREG32_SSC_OFFSET_MASK, PHYREG32_SSC_OFFSET_500PPM);
-			rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, val, PHYREG32);
+			val = FIELD_PREP(RK3568_PHYREG32_SSC_DIR_MASK,
+					 RK3568_PHYREG32_SSC_DOWNWARD);
+			val |= FIELD_PREP(RK3568_PHYREG32_SSC_OFFSET_MASK,
+					  RK3568_PHYREG32_SSC_OFFSET_500PPM);
+			rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val,
+						 RK3568_PHYREG32);
 
 			/* ssc ppm adjust to 3500ppm */
-			rockchip_combphy_updatel(priv, PHYREG10_SSC_PCM_MASK,
-						 PHYREG10_SSC_PCM_3500PPM,
-						 PHYREG10);
+			rockchip_combphy_updatel(priv, RK3576_PHYREG10_SSC_PCM_MASK,
+						 RK3576_PHYREG10_SSC_PCM_3500PPM,
+						 RK3576_PHYREG10);
 		}
 		break;
 
@@ -912,12 +925,13 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
 	if (priv->ext_refclk) {
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_ext, true);
 		if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) {
-			val = FIELD_PREP(PHYREG33_PLL_KVCO_MASK, PHYREG33_PLL_KVCO_VALUE_RK3576);
-			rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
-						 val, PHYREG33);
+			val = FIELD_PREP(RK3568_PHYREG33_PLL_KVCO_MASK,
+					 RK3576_PHYREG33_PLL_KVCO_VALUE);
+			rockchip_combphy_updatel(priv, RK3568_PHYREG33_PLL_KVCO_MASK,
+						 val, RK3568_PHYREG33);
 
 			/* Set up rx_trim: PLL LPF C1 85pf R1 2.5kohm */
-			writel(0x0c, priv->mmio + PHYREG27);
+			writel(0x0c, priv->mmio + RK3588_PHYREG27);
 
 			/*
 			 * Set up SU adjust signal:
@@ -927,25 +941,25 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
 			 * su_trim[23:16], CKRCV adjust
 			 * su_trim[31:24], CKDRV adjust
 			 */
-			writel(0x90, priv->mmio + PHYREG11);
-			writel(0x43, priv->mmio + PHYREG12);
-			writel(0x88, priv->mmio + PHYREG13);
-			writel(0x56, priv->mmio + PHYREG14);
+			writel(0x90, priv->mmio + RK3568_PHYREG11);
+			writel(0x43, priv->mmio + RK3568_PHYREG12);
+			writel(0x88, priv->mmio + RK3568_PHYREG13);
+			writel(0x56, priv->mmio + RK3568_PHYREG14);
 		}
 	}
 
 	if (priv->enable_ssc) {
-		val = readl(priv->mmio + PHYREG8);
-		val |= PHYREG8_SSC_EN;
-		writel(val, priv->mmio + PHYREG8);
+		val = readl(priv->mmio + RK3568_PHYREG8);
+		val |= RK3568_PHYREG8_SSC_EN;
+		writel(val, priv->mmio + RK3568_PHYREG8);
 
 		if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_24MHz) {
 			/* Set PLL loop divider */
-			writel(0x00, priv->mmio + PHYREG17);
-			writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18);
+			writel(0x00, priv->mmio + RK3576_PHYREG17);
+			writel(RK3568_PHYREG18_PLL_LOOP, priv->mmio + RK3568_PHYREG18);
 
 			/* Set up rx_pck invert and rx msb to disable */
-			writel(0x00, priv->mmio + PHYREG27);
+			writel(0x00, priv->mmio + RK3588_PHYREG27);
 
 			/*
 			 * Set up SU adjust signal:
@@ -954,16 +968,17 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
 			 * su_trim[23:16], CKRCV adjust
 			 * su_trim[31:24], CKDRV adjust
 			 */
-			writel(0x90, priv->mmio + PHYREG11);
-			writel(0x02, priv->mmio + PHYREG12);
-			writel(0x08, priv->mmio + PHYREG13);
-			writel(0x57, priv->mmio + PHYREG14);
-			writel(0x40, priv->mmio + PHYREG15);
+			writel(0x90, priv->mmio + RK3568_PHYREG11);
+			writel(0x02, priv->mmio + RK3568_PHYREG12);
+			writel(0x08, priv->mmio + RK3568_PHYREG13);
+			writel(0x57, priv->mmio + RK3568_PHYREG14);
+			writel(0x40, priv->mmio + RK3568_PHYREG15);
 
-			writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
+			writel(RK3568_PHYREG16_SSC_CNT_VALUE, priv->mmio + RK3568_PHYREG16);
 
-			val = FIELD_PREP(PHYREG33_PLL_KVCO_MASK, PHYREG33_PLL_KVCO_VALUE_RK3576);
-			writel(val, priv->mmio + PHYREG33);
+			val = FIELD_PREP(RK3568_PHYREG33_PLL_KVCO_MASK,
+					 RK3576_PHYREG33_PLL_KVCO_VALUE);
+			writel(val, priv->mmio + RK3568_PHYREG33);
 		}
 	}
 
@@ -1033,30 +1048,28 @@ static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv)
 		break;
 	case PHY_TYPE_USB3:
 		/* Set SSC downward spread spectrum */
-		rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK,
-					 PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT,
-					 PHYREG32);
+		val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
+		rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
 
 		/* Enable adaptive CTLE for USB3.0 Rx. */
-		val = readl(priv->mmio + PHYREG15);
-		val |= PHYREG15_CTLE_EN;
-		writel(val, priv->mmio + PHYREG15);
+		val = readl(priv->mmio + RK3568_PHYREG15);
+		val |= RK3568_PHYREG15_CTLE_EN;
+		writel(val, priv->mmio + RK3568_PHYREG15);
 
 		/* Set PLL KVCO fine tuning signals. */
-		rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
-					 PHYREG33_PLL_KVCO_VALUE << PHYREG33_PLL_KVCO_SHIFT,
-					 PHYREG33);
+		val = RK3568_PHYREG33_PLL_KVCO_VALUE << RK3568_PHYREG33_PLL_KVCO_SHIFT,
+		rockchip_combphy_updatel(priv, RK3568_PHYREG33_PLL_KVCO_MASK, val, RK3568_PHYREG33);
 
 		/* Enable controlling random jitter. */
-		writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12);
+		writel(RK3568_PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + RK3568_PHYREG12);
 
 		/* Set PLL input clock divider 1/2. */
-		rockchip_combphy_updatel(priv, PHYREG6_PLL_DIV_MASK,
-					 PHYREG6_PLL_DIV_2 << PHYREG6_PLL_DIV_SHIFT,
-					 PHYREG6);
+		rockchip_combphy_updatel(priv, RK3568_PHYREG6_PLL_DIV_MASK,
+					 RK3568_PHYREG6_PLL_DIV_2 << RK3568_PHYREG6_PLL_DIV_SHIFT,
+					 RK3568_PHYREG6);
 
-		writel(PHYREG18_PLL_LOOP, priv->mmio + PHYREG18);
-		writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11);
+		writel(RK3568_PHYREG18_PLL_LOOP, priv->mmio + RK3568_PHYREG18);
+		writel(RK3568_PHYREG11_SU_TRIM_0_7, priv->mmio + RK3568_PHYREG11);
 
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txelec_sel, false);
@@ -1064,16 +1077,16 @@ static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv)
 		break;
 	case PHY_TYPE_SATA:
 		/* Enable adaptive CTLE for SATA Rx. */
-		val = readl(priv->mmio + PHYREG15);
-		val |= PHYREG15_CTLE_EN;
-		writel(val, priv->mmio + PHYREG15);
+		val = readl(priv->mmio + RK3568_PHYREG15);
+		val |= RK3568_PHYREG15_CTLE_EN;
+		writel(val, priv->mmio + RK3568_PHYREG15);
 		/*
 		 * Set tx_rterm=50ohm and rx_rterm=44ohm for SATA.
 		 * 0: 60ohm, 8: 50ohm 15: 44ohm (by step abort 1ohm)
 		 */
-		val = PHYREG7_TX_RTERM_50OHM << PHYREG7_TX_RTERM_SHIFT;
-		val |= PHYREG7_RX_RTERM_44OHM << PHYREG7_RX_RTERM_SHIFT;
-		writel(val, priv->mmio + PHYREG7);
+		val = RK3568_PHYREG7_TX_RTERM_50OHM << RK3568_PHYREG7_TX_RTERM_SHIFT;
+		val |= RK3568_PHYREG7_RX_RTERM_44OHM << RK3568_PHYREG7_RX_RTERM_SHIFT;
+		writel(val, priv->mmio + RK3568_PHYREG7);
 
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_sata, true);
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_sata, true);
@@ -1095,11 +1108,11 @@ static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv)
 	case REF_CLOCK_24MHz:
 		if (priv->type == PHY_TYPE_USB3 || priv->type == PHY_TYPE_SATA) {
 			/* Set ssc_cnt[9:0]=0101111101 & 31.5KHz. */
-			val = PHYREG15_SSC_CNT_VALUE << PHYREG15_SSC_CNT_SHIFT;
-			rockchip_combphy_updatel(priv, PHYREG15_SSC_CNT_MASK,
-						 val, PHYREG15);
+			val = RK3568_PHYREG15_SSC_CNT_VALUE << RK3568_PHYREG15_SSC_CNT_SHIFT;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG15_SSC_CNT_MASK,
+						 val, RK3568_PHYREG15);
 
-			writel(PHYREG16_SSC_CNT_VALUE, priv->mmio + PHYREG16);
+			writel(RK3568_PHYREG16_SSC_CNT_VALUE, priv->mmio + RK3568_PHYREG16);
 		}
 		break;
 
@@ -1110,23 +1123,25 @@ static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv)
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_100m, true);
 		if (priv->type == PHY_TYPE_PCIE) {
 			/* PLL KVCO fine tuning. */
-			val = 4 << PHYREG33_PLL_KVCO_SHIFT;
-			rockchip_combphy_updatel(priv, PHYREG33_PLL_KVCO_MASK,
-						 val, PHYREG33);
+			val = 4 << RK3568_PHYREG33_PLL_KVCO_SHIFT;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG33_PLL_KVCO_MASK,
+						 val, RK3568_PHYREG33);
 
 			/* Enable controlling random jitter. */
-			writel(PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + PHYREG12);
+			writel(RK3568_PHYREG12_PLL_LPF_ADJ_VALUE, priv->mmio + RK3568_PHYREG12);
 
 			/* Set up rx_trim: PLL LPF C1 85pf R1 1.25kohm */
-			writel(PHYREG27_RX_TRIM_RK3588, priv->mmio + PHYREG27);
+			writel(RK3588_PHYREG27_RX_TRIM, priv->mmio + RK3588_PHYREG27);
 
 			/* Set up su_trim:  */
-			writel(PHYREG11_SU_TRIM_0_7, priv->mmio + PHYREG11);
+			writel(RK3568_PHYREG11_SU_TRIM_0_7, priv->mmio + RK3568_PHYREG11);
 		} else if (priv->type == PHY_TYPE_SATA) {
 			/* downward spread spectrum +500ppm */
-			val = PHYREG32_SSC_DOWNWARD << PHYREG32_SSC_DIR_SHIFT;
-			val |= PHYREG32_SSC_OFFSET_500PPM << PHYREG32_SSC_OFFSET_SHIFT;
-			rockchip_combphy_updatel(priv, PHYREG32_SSC_MASK, val, PHYREG32);
+			val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
+			val |= RK3568_PHYREG32_SSC_OFFSET_500PPM <<
+			       RK3568_PHYREG32_SSC_OFFSET_SHIFT;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val,
+						 RK3568_PHYREG32);
 		}
 		break;
 	default:
@@ -1137,20 +1152,21 @@ static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv)
 	if (priv->ext_refclk) {
 		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_ext, true);
 		if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) {
-			val = PHYREG13_RESISTER_HIGH_Z << PHYREG13_RESISTER_SHIFT;
-			val |= PHYREG13_CKRCV_AMP0;
-			rockchip_combphy_updatel(priv, PHYREG13_RESISTER_MASK, val, PHYREG13);
-
-			val = readl(priv->mmio + PHYREG14);
-			val |= PHYREG14_CKRCV_AMP1;
-			writel(val, priv->mmio + PHYREG14);
+			val = RK3568_PHYREG13_RESISTER_HIGH_Z << RK3568_PHYREG13_RESISTER_SHIFT;
+			val |= RK3568_PHYREG13_CKRCV_AMP0;
+			rockchip_combphy_updatel(priv, RK3568_PHYREG13_RESISTER_MASK, val,
+						 RK3568_PHYREG13);
+
+			val = readl(priv->mmio + RK3568_PHYREG14);
+			val |= RK3568_PHYREG14_CKRCV_AMP1;
+			writel(val, priv->mmio + RK3568_PHYREG14);
 		}
 	}
 
 	if (priv->enable_ssc) {
-		val = readl(priv->mmio + PHYREG8);
-		val |= PHYREG8_SSC_EN;
-		writel(val, priv->mmio + PHYREG8);
+		val = readl(priv->mmio + RK3568_PHYREG8);
+		val |= RK3568_PHYREG8_SSC_EN;
+		writel(val, priv->mmio + RK3568_PHYREG8);
 	}
 
 	return 0;
Signature · 1 line
2.49.0
#5 lore raw

Re: [PATCH v3 3/5] phy: rockchip: naneng-combphy: Add SoC prefix to register definitions

Quoted 77 lines · Yao Zi

All supported variants of naneng-combphy follow a register layout similar to the RK3568 variant with some exceptions of SoC-specific registers.

Add RK3568 prefix for the common set of registers and the corresponding SoC prefix for SoC-specific registers, making usage of definitions clear and preparing for future COMBPHY variants with a different register layout.

---
 .../rockchip/phy-rockchip-naneng-combphy.c    | 560 +++++++++---------
 1 file changed, 288 insertions(+), 272 deletions(-)
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +52 -1
index ce91fb1d5167..1d1c7723584b 100644
@@ -21,78 +21,80 @@
 #define REF_CLOCK_100MHz		(100 * HZ_PER_MHZ)
 
 /* COMBO PHY REG */
<snip>
-#define PHYREG33_PLL_KVCO_VALUE_RK3576	4
+#define RK3568_PHYREG6				0x14
+#define RK3568_PHYREG6_PLL_DIV_MASK		GENMASK(7, 6)
+#define RK3568_PHYREG6_PLL_DIV_SHIFT		6
+#define RK3568_PHYREG6_PLL_DIV_2		1
+
+#define RK3568_PHYREG7				0x18
+#define RK3568_PHYREG7_TX_RTERM_MASK		GENMASK(7, 4)
+#define RK3568_PHYREG7_TX_RTERM_SHIFT		4
+#define RK3568_PHYREG7_TX_RTERM_50OHM		8
+#define RK3568_PHYREG7_RX_RTERM_MASK		GENMASK(3, 0)
+#define RK3568_PHYREG7_RX_RTERM_SHIFT		0
+#define RK3568_PHYREG7_RX_RTERM_44OHM		15
+
+#define RK3568_PHYREG8				0x1C
+#define RK3568_PHYREG8_SSC_EN			BIT(4)
+
+#define RK3568_PHYREG11				0x28
+#define RK3568_PHYREG11_SU_TRIM_0_7		0xF0
+
+#define RK3568_PHYREG12				0x2C
+#define RK3568_PHYREG12_PLL_LPF_ADJ_VALUE	4
+
+#define RK3568_PHYREG13				0x30
+#define RK3568_PHYREG13_RESISTER_MASK		GENMASK(5, 4)
+#define RK3568_PHYREG13_RESISTER_SHIFT		0x4
+#define RK3568_PHYREG13_RESISTER_HIGH_Z		3
+#define RK3568_PHYREG13_CKRCV_AMP0		BIT(7)
+
+#define RK3568_PHYREG14				0x34
+#define RK3568_PHYREG14_CKRCV_AMP1		BIT(0)
+
+#define RK3568_PHYREG15				0x38
+#define RK3568_PHYREG15_CTLE_EN			BIT(0)
+#define RK3568_PHYREG15_SSC_CNT_MASK		GENMASK(7, 6)
+#define RK3568_PHYREG15_SSC_CNT_SHIFT		6
+#define RK3568_PHYREG15_SSC_CNT_VALUE		1
+
+#define RK3568_PHYREG16				0x3C
+#define RK3568_PHYREG16_SSC_CNT_VALUE		0x5f
+
+#define RK3568_PHYREG18				0x44
+#define RK3568_PHYREG18_PLL_LOOP		0x32
+
+#define RK3568_PHYREG32				0x7C
+#define RK3568_PHYREG32_SSC_MASK		GENMASK(7, 4)
+#define RK3568_PHYREG32_SSC_DIR_MASK		GENMASK(5, 4)
+#define RK3568_PHYREG32_SSC_DIR_SHIFT		4
+#define RK3568_PHYREG32_SSC_UPWARD		0
+#define RK3568_PHYREG32_SSC_DOWNWARD		1
+#define RK3568_PHYREG32_SSC_OFFSET_MASK	GENMASK(7, 6)
+#define RK3568_PHYREG32_SSC_OFFSET_SHIFT	6
+#define RK3568_PHYREG32_SSC_OFFSET_500PPM	1

drivers/phy/rockchip/phy-rockchip-naneng-combphy.c line 85

Quoted 10 lines
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +10 -0
+
+#define RK3568_PHYREG33				0x80
+#define RK3568_PHYREG33_PLL_KVCO_MASK		GENMASK(4, 2)
+#define RK3568_PHYREG33_PLL_KVCO_SHIFT		2
+#define RK3568_PHYREG33_PLL_KVCO_VALUE		2
+#define RK3576_PHYREG33_PLL_KVCO_VALUE		4
+
+/* RK3588 COMBO PHY registers */
+#define RK3588_PHYREG27				0x6C
+#define RK3588_PHYREG27_RX_TRIM			0x4C

Would it be better if RK3588_PHYREG* comes after RK3576_PHYREG*?

Cheers,
Diederik

Quoted 15 lines
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +12 -0
+
+/* RK3576 COMBO PHY registers */
+#define RK3576_PHYREG10				0x24
+#define RK3576_PHYREG10_SSC_PCM_MASK		GENMASK(3, 0)
+#define RK3576_PHYREG10_SSC_PCM_3500PPM		7
+
+#define RK3576_PHYREG17				0x40
+
+#define RK3576_PHYREG21				0x50
+#define RK3576_PHYREG21_RX_SQUELCH_VAL		0x0D
+
+#define RK3576_PHYREG30				0x74
 
 struct rockchip_combphy_priv;
<snip>
author
#6 lore raw

Re: [PATCH v3 3/5] phy: rockchip: naneng-combphy: Add SoC prefix to register definitions

Quoted 91 lines · Diederik de Haas
Quoted 77 lines · Yao Zi

All supported variants of naneng-combphy follow a register layout similar to the RK3568 variant with some exceptions of SoC-specific registers.

Add RK3568 prefix for the common set of registers and the corresponding SoC prefix for SoC-specific registers, making usage of definitions clear and preparing for future COMBPHY variants with a different register layout.

---
 .../rockchip/phy-rockchip-naneng-combphy.c    | 560 +++++++++---------
 1 file changed, 288 insertions(+), 272 deletions(-)
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +52 -1
index ce91fb1d5167..1d1c7723584b 100644
@@ -21,78 +21,80 @@
 #define REF_CLOCK_100MHz		(100 * HZ_PER_MHZ)
 
 /* COMBO PHY REG */
<snip>
-#define PHYREG33_PLL_KVCO_VALUE_RK3576	4
+#define RK3568_PHYREG6				0x14
+#define RK3568_PHYREG6_PLL_DIV_MASK		GENMASK(7, 6)
+#define RK3568_PHYREG6_PLL_DIV_SHIFT		6
+#define RK3568_PHYREG6_PLL_DIV_2		1
+
+#define RK3568_PHYREG7				0x18
+#define RK3568_PHYREG7_TX_RTERM_MASK		GENMASK(7, 4)
+#define RK3568_PHYREG7_TX_RTERM_SHIFT		4
+#define RK3568_PHYREG7_TX_RTERM_50OHM		8
+#define RK3568_PHYREG7_RX_RTERM_MASK		GENMASK(3, 0)
+#define RK3568_PHYREG7_RX_RTERM_SHIFT		0
+#define RK3568_PHYREG7_RX_RTERM_44OHM		15
+
+#define RK3568_PHYREG8				0x1C
+#define RK3568_PHYREG8_SSC_EN			BIT(4)
+
+#define RK3568_PHYREG11				0x28
+#define RK3568_PHYREG11_SU_TRIM_0_7		0xF0
+
+#define RK3568_PHYREG12				0x2C
+#define RK3568_PHYREG12_PLL_LPF_ADJ_VALUE	4
+
+#define RK3568_PHYREG13				0x30
+#define RK3568_PHYREG13_RESISTER_MASK		GENMASK(5, 4)
+#define RK3568_PHYREG13_RESISTER_SHIFT		0x4
+#define RK3568_PHYREG13_RESISTER_HIGH_Z		3
+#define RK3568_PHYREG13_CKRCV_AMP0		BIT(7)
+
+#define RK3568_PHYREG14				0x34
+#define RK3568_PHYREG14_CKRCV_AMP1		BIT(0)
+
+#define RK3568_PHYREG15				0x38
+#define RK3568_PHYREG15_CTLE_EN			BIT(0)
+#define RK3568_PHYREG15_SSC_CNT_MASK		GENMASK(7, 6)
+#define RK3568_PHYREG15_SSC_CNT_SHIFT		6
+#define RK3568_PHYREG15_SSC_CNT_VALUE		1
+
+#define RK3568_PHYREG16				0x3C
+#define RK3568_PHYREG16_SSC_CNT_VALUE		0x5f
+
+#define RK3568_PHYREG18				0x44
+#define RK3568_PHYREG18_PLL_LOOP		0x32
+
+#define RK3568_PHYREG32				0x7C
+#define RK3568_PHYREG32_SSC_MASK		GENMASK(7, 4)
+#define RK3568_PHYREG32_SSC_DIR_MASK		GENMASK(5, 4)
+#define RK3568_PHYREG32_SSC_DIR_SHIFT		4
+#define RK3568_PHYREG32_SSC_UPWARD		0
+#define RK3568_PHYREG32_SSC_DOWNWARD		1
+#define RK3568_PHYREG32_SSC_OFFSET_MASK	GENMASK(7, 6)
+#define RK3568_PHYREG32_SSC_OFFSET_SHIFT	6
+#define RK3568_PHYREG32_SSC_OFFSET_500PPM	1

drivers/phy/rockchip/phy-rockchip-naneng-combphy.c line 85

Quoted 10 lines
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +10 -0
+
+#define RK3568_PHYREG33				0x80
+#define RK3568_PHYREG33_PLL_KVCO_MASK		GENMASK(4, 2)
+#define RK3568_PHYREG33_PLL_KVCO_SHIFT		2
+#define RK3568_PHYREG33_PLL_KVCO_VALUE		2
+#define RK3576_PHYREG33_PLL_KVCO_VALUE		4
+
+/* RK3588 COMBO PHY registers */
+#define RK3588_PHYREG27				0x6C
+#define RK3588_PHYREG27_RX_TRIM			0x4C

Would it be better if RK3588_PHYREG* comes after RK3576_PHYREG*?

Quoted 2 lines

Cheers,
Diederik

It's intended to keep RK3576 definitions below RK3588 ones. The RK3576 driver makes use of a register introduced for RK3588 variant (RK3588_PHYREG27). Since similar reusing doesn't happen reversely, I consider the design of RK3576 a superset of the RK3588 one, and put RK3576 definitions later in the file.

Quoted 13 lines
Quoted 13 lines
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +12 -0
+
+/* RK3576 COMBO PHY registers */
+#define RK3576_PHYREG10				0x24
+#define RK3576_PHYREG10_SSC_PCM_MASK		GENMASK(3, 0)
+#define RK3576_PHYREG10_SSC_PCM_3500PPM		7
+
+#define RK3576_PHYREG17				0x40
+
+#define RK3576_PHYREG21				0x50
+#define RK3576_PHYREG21_RX_SQUELCH_VAL		0x0D
+
+#define RK3576_PHYREG30				0x74
Quoted 2 lines
Quoted 2 lines

struct rockchip_combphy_priv;
<snip>

Thanks,
Yao Zi

reviewer Reviewed-by
#7 lore raw

Re: [PATCH v3 3/5] phy: rockchip: naneng-combphy: Add SoC prefix to register definitions

Quoted 92 lines · Yao Zi
Quoted 91 lines · Diederik de Haas
Quoted 77 lines · Yao Zi

All supported variants of naneng-combphy follow a register layout similar to the RK3568 variant with some exceptions of SoC-specific registers.

Add RK3568 prefix for the common set of registers and the corresponding SoC prefix for SoC-specific registers, making usage of definitions clear and preparing for future COMBPHY variants with a different register layout.

---
  .../rockchip/phy-rockchip-naneng-combphy.c    | 560 +++++++++---------
  1 file changed, 288 insertions(+), 272 deletions(-)
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +52 -1
index ce91fb1d5167..1d1c7723584b 100644
@@ -21,78 +21,80 @@
  #define REF_CLOCK_100MHz		(100 * HZ_PER_MHZ)
 
  /* COMBO PHY REG */
<snip>
-#define PHYREG33_PLL_KVCO_VALUE_RK3576	4
+#define RK3568_PHYREG6				0x14
+#define RK3568_PHYREG6_PLL_DIV_MASK		GENMASK(7, 6)
+#define RK3568_PHYREG6_PLL_DIV_SHIFT		6
+#define RK3568_PHYREG6_PLL_DIV_2		1
+
+#define RK3568_PHYREG7				0x18
+#define RK3568_PHYREG7_TX_RTERM_MASK		GENMASK(7, 4)
+#define RK3568_PHYREG7_TX_RTERM_SHIFT		4
+#define RK3568_PHYREG7_TX_RTERM_50OHM		8
+#define RK3568_PHYREG7_RX_RTERM_MASK		GENMASK(3, 0)
+#define RK3568_PHYREG7_RX_RTERM_SHIFT		0
+#define RK3568_PHYREG7_RX_RTERM_44OHM		15
+
+#define RK3568_PHYREG8				0x1C
+#define RK3568_PHYREG8_SSC_EN			BIT(4)
+
+#define RK3568_PHYREG11				0x28
+#define RK3568_PHYREG11_SU_TRIM_0_7		0xF0
+
+#define RK3568_PHYREG12				0x2C
+#define RK3568_PHYREG12_PLL_LPF_ADJ_VALUE	4
+
+#define RK3568_PHYREG13				0x30
+#define RK3568_PHYREG13_RESISTER_MASK		GENMASK(5, 4)
+#define RK3568_PHYREG13_RESISTER_SHIFT		0x4
+#define RK3568_PHYREG13_RESISTER_HIGH_Z		3
+#define RK3568_PHYREG13_CKRCV_AMP0		BIT(7)
+
+#define RK3568_PHYREG14				0x34
+#define RK3568_PHYREG14_CKRCV_AMP1		BIT(0)
+
+#define RK3568_PHYREG15				0x38
+#define RK3568_PHYREG15_CTLE_EN			BIT(0)
+#define RK3568_PHYREG15_SSC_CNT_MASK		GENMASK(7, 6)
+#define RK3568_PHYREG15_SSC_CNT_SHIFT		6
+#define RK3568_PHYREG15_SSC_CNT_VALUE		1
+
+#define RK3568_PHYREG16				0x3C
+#define RK3568_PHYREG16_SSC_CNT_VALUE		0x5f
+
+#define RK3568_PHYREG18				0x44
+#define RK3568_PHYREG18_PLL_LOOP		0x32
+
+#define RK3568_PHYREG32				0x7C
+#define RK3568_PHYREG32_SSC_MASK		GENMASK(7, 4)
+#define RK3568_PHYREG32_SSC_DIR_MASK		GENMASK(5, 4)
+#define RK3568_PHYREG32_SSC_DIR_SHIFT		4
+#define RK3568_PHYREG32_SSC_UPWARD		0
+#define RK3568_PHYREG32_SSC_DOWNWARD		1
+#define RK3568_PHYREG32_SSC_OFFSET_MASK	GENMASK(7, 6)
+#define RK3568_PHYREG32_SSC_OFFSET_SHIFT	6
+#define RK3568_PHYREG32_SSC_OFFSET_500PPM	1

drivers/phy/rockchip/phy-rockchip-naneng-combphy.c line 85

Quoted 10 lines
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +10 -0
+
+#define RK3568_PHYREG33				0x80
+#define RK3568_PHYREG33_PLL_KVCO_MASK		GENMASK(4, 2)
+#define RK3568_PHYREG33_PLL_KVCO_SHIFT		2
+#define RK3568_PHYREG33_PLL_KVCO_VALUE		2
+#define RK3576_PHYREG33_PLL_KVCO_VALUE		4
+
+/* RK3588 COMBO PHY registers */
+#define RK3588_PHYREG27				0x6C
+#define RK3588_PHYREG27_RX_TRIM			0x4C

Would it be better if RK3588_PHYREG* comes after RK3576_PHYREG*?

Quoted 8 lines
Quoted 2 lines

Cheers,
Diederik

It's intended to keep RK3576 definitions below RK3588 ones. The RK3576 driver makes use of a register introduced for RK3588 variant (RK3588_PHYREG27). Since similar reusing doesn't happen reversely, I consider the design of RK3576 a superset of the RK3588 one, and put RK3576 definitions later in the file.

Sound logic, RK3576 was announced after RK3588, thus the order makes sense.

Add my:

Quoted 21 lines
Quoted 14 lines
Quoted 14 lines
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +12 -0
+
+/* RK3576 COMBO PHY registers */
+#define RK3576_PHYREG10				0x24
+#define RK3576_PHYREG10_SSC_PCM_MASK		GENMASK(3, 0)
+#define RK3576_PHYREG10_SSC_PCM_3500PPM		7
+
+#define RK3576_PHYREG17				0x40
+
+#define RK3576_PHYREG21				0x50
+#define RK3576_PHYREG21_RX_SQUELCH_VAL		0x0D
+
+#define RK3576_PHYREG30				0x74
Quoted 2 lines
Quoted 2 lines

struct rockchip_combphy_priv;
<snip>

Thanks,
Yao Zi

#8 lore raw

Re: [PATCH v3 3/5] phy: rockchip: naneng-combphy: Add SoC prefix to register definitions

In reply to Yao Zi
Quoted 93 lines · Yao Zi
Quoted 82 lines · Diederik de Haas
Quoted 81 lines · Yao Zi

All supported variants of naneng-combphy follow a register layout similar to the RK3568 variant with some exceptions of SoC-specific registers.

Add RK3568 prefix for the common set of registers and the corresponding SoC prefix for SoC-specific registers, making usage of definitions clear and preparing for future COMBPHY variants with a different register layout.

---
 .../rockchip/phy-rockchip-naneng-combphy.c    | 560 +++++++++---------
 1 file changed, 288 insertions(+), 272 deletions(-)
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +56 -1
index ce91fb1d5167..1d1c7723584b 100644
@@ -21,78 +21,80 @@
 #define REF_CLOCK_100MHz		(100 * HZ_PER_MHZ)
 
 /* COMBO PHY REG */
<snip>
-#define PHYREG33_PLL_KVCO_VALUE_RK3576	4
+#define RK3568_PHYREG6				0x14
+#define RK3568_PHYREG6_PLL_DIV_MASK		GENMASK(7, 6)
+#define RK3568_PHYREG6_PLL_DIV_SHIFT		6
+#define RK3568_PHYREG6_PLL_DIV_2		1
+
+#define RK3568_PHYREG7				0x18
+#define RK3568_PHYREG7_TX_RTERM_MASK		GENMASK(7, 4)
+#define RK3568_PHYREG7_TX_RTERM_SHIFT		4
+#define RK3568_PHYREG7_TX_RTERM_50OHM		8
+#define RK3568_PHYREG7_RX_RTERM_MASK		GENMASK(3, 0)
+#define RK3568_PHYREG7_RX_RTERM_SHIFT		0
+#define RK3568_PHYREG7_RX_RTERM_44OHM		15
+
+#define RK3568_PHYREG8				0x1C
+#define RK3568_PHYREG8_SSC_EN			BIT(4)
+
+#define RK3568_PHYREG11				0x28
+#define RK3568_PHYREG11_SU_TRIM_0_7		0xF0
+
+#define RK3568_PHYREG12				0x2C
+#define RK3568_PHYREG12_PLL_LPF_ADJ_VALUE	4
+
+#define RK3568_PHYREG13				0x30
+#define RK3568_PHYREG13_RESISTER_MASK		GENMASK(5, 4)
+#define RK3568_PHYREG13_RESISTER_SHIFT		0x4
+#define RK3568_PHYREG13_RESISTER_HIGH_Z		3
+#define RK3568_PHYREG13_CKRCV_AMP0		BIT(7)
+
+#define RK3568_PHYREG14				0x34
+#define RK3568_PHYREG14_CKRCV_AMP1		BIT(0)
+
+#define RK3568_PHYREG15				0x38
+#define RK3568_PHYREG15_CTLE_EN			BIT(0)
+#define RK3568_PHYREG15_SSC_CNT_MASK		GENMASK(7, 6)
+#define RK3568_PHYREG15_SSC_CNT_SHIFT		6
+#define RK3568_PHYREG15_SSC_CNT_VALUE		1
+
+#define RK3568_PHYREG16				0x3C
+#define RK3568_PHYREG16_SSC_CNT_VALUE		0x5f
+
+#define RK3568_PHYREG18				0x44
+#define RK3568_PHYREG18_PLL_LOOP		0x32
+
+#define RK3568_PHYREG32				0x7C
+#define RK3568_PHYREG32_SSC_MASK		GENMASK(7, 4)
+#define RK3568_PHYREG32_SSC_DIR_MASK		GENMASK(5, 4)
+#define RK3568_PHYREG32_SSC_DIR_SHIFT		4
+#define RK3568_PHYREG32_SSC_UPWARD		0
+#define RK3568_PHYREG32_SSC_DOWNWARD		1
+#define RK3568_PHYREG32_SSC_OFFSET_MASK	GENMASK(7, 6)
+#define RK3568_PHYREG32_SSC_OFFSET_SHIFT	6
+#define RK3568_PHYREG32_SSC_OFFSET_500PPM	1
+
+#define RK3568_PHYREG33				0x80
+#define RK3568_PHYREG33_PLL_KVCO_MASK		GENMASK(4, 2)
+#define RK3568_PHYREG33_PLL_KVCO_SHIFT		2
Quoted 9 lines

drivers/phy/rockchip/phy-rockchip-naneng-combphy.c line 85

Quoted 6 lines
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +6 -0
+#define RK3568_PHYREG33_PLL_KVCO_VALUE		2
+#define RK3576_PHYREG33_PLL_KVCO_VALUE		4
+
+/* RK3588 COMBO PHY registers */
+#define RK3588_PHYREG27				0x6C
+#define RK3588_PHYREG27_RX_TRIM			0x4C

Would it be better if RK3588_PHYREG* comes after RK3576_PHYREG*?

Quoted 5 lines

It's intended to keep RK3576 definitions below RK3588 ones. The RK3576 driver makes use of a register introduced for RK3588 variant (RK3588_PHYREG27). Since similar reusing doesn't happen reversely, I consider the design of RK3576 a superset of the RK3588 one, and put RK3576 definitions later in the file.

I understand that logic, but OTOH in patch 4 you put the defines for RK3528 before RK3568. And RK3568 is not a superset of RK3528 AFAIK. It's just different? That's why I think/thought sorting them (all) alphabetically would make more sense.

My 0.02

Quoted 19 lines
Quoted 13 lines
Quoted 13 lines
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +12 -0
+
+/* RK3576 COMBO PHY registers */
+#define RK3576_PHYREG10				0x24
+#define RK3576_PHYREG10_SSC_PCM_MASK		GENMASK(3, 0)
+#define RK3576_PHYREG10_SSC_PCM_3500PPM		7
+
+#define RK3576_PHYREG17				0x40
+
+#define RK3576_PHYREG21				0x50
+#define RK3576_PHYREG21_RX_SQUELCH_VAL		0x0D
+
+#define RK3576_PHYREG30				0x74
Quoted 2 lines
Quoted 2 lines

struct rockchip_combphy_priv;
<snip>

Thanks,
Yao Zi

author
#9 lore raw

Re: [PATCH v3 3/5] phy: rockchip: naneng-combphy: Add SoC prefix to register definitions

Quoted 100 lines · Diederik de Haas
Quoted 93 lines · Yao Zi
Quoted 82 lines · Diederik de Haas
Quoted 81 lines · Yao Zi

All supported variants of naneng-combphy follow a register layout similar to the RK3568 variant with some exceptions of SoC-specific registers.

Add RK3568 prefix for the common set of registers and the corresponding SoC prefix for SoC-specific registers, making usage of definitions clear and preparing for future COMBPHY variants with a different register layout.

---
 .../rockchip/phy-rockchip-naneng-combphy.c    | 560 +++++++++---------
 1 file changed, 288 insertions(+), 272 deletions(-)
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +56 -1
index ce91fb1d5167..1d1c7723584b 100644
@@ -21,78 +21,80 @@
 #define REF_CLOCK_100MHz		(100 * HZ_PER_MHZ)
 
 /* COMBO PHY REG */
<snip>
-#define PHYREG33_PLL_KVCO_VALUE_RK3576	4
+#define RK3568_PHYREG6				0x14
+#define RK3568_PHYREG6_PLL_DIV_MASK		GENMASK(7, 6)
+#define RK3568_PHYREG6_PLL_DIV_SHIFT		6
+#define RK3568_PHYREG6_PLL_DIV_2		1
+
+#define RK3568_PHYREG7				0x18
+#define RK3568_PHYREG7_TX_RTERM_MASK		GENMASK(7, 4)
+#define RK3568_PHYREG7_TX_RTERM_SHIFT		4
+#define RK3568_PHYREG7_TX_RTERM_50OHM		8
+#define RK3568_PHYREG7_RX_RTERM_MASK		GENMASK(3, 0)
+#define RK3568_PHYREG7_RX_RTERM_SHIFT		0
+#define RK3568_PHYREG7_RX_RTERM_44OHM		15
+
+#define RK3568_PHYREG8				0x1C
+#define RK3568_PHYREG8_SSC_EN			BIT(4)
+
+#define RK3568_PHYREG11				0x28
+#define RK3568_PHYREG11_SU_TRIM_0_7		0xF0
+
+#define RK3568_PHYREG12				0x2C
+#define RK3568_PHYREG12_PLL_LPF_ADJ_VALUE	4
+
+#define RK3568_PHYREG13				0x30
+#define RK3568_PHYREG13_RESISTER_MASK		GENMASK(5, 4)
+#define RK3568_PHYREG13_RESISTER_SHIFT		0x4
+#define RK3568_PHYREG13_RESISTER_HIGH_Z		3
+#define RK3568_PHYREG13_CKRCV_AMP0		BIT(7)
+
+#define RK3568_PHYREG14				0x34
+#define RK3568_PHYREG14_CKRCV_AMP1		BIT(0)
+
+#define RK3568_PHYREG15				0x38
+#define RK3568_PHYREG15_CTLE_EN			BIT(0)
+#define RK3568_PHYREG15_SSC_CNT_MASK		GENMASK(7, 6)
+#define RK3568_PHYREG15_SSC_CNT_SHIFT		6
+#define RK3568_PHYREG15_SSC_CNT_VALUE		1
+
+#define RK3568_PHYREG16				0x3C
+#define RK3568_PHYREG16_SSC_CNT_VALUE		0x5f
+
+#define RK3568_PHYREG18				0x44
+#define RK3568_PHYREG18_PLL_LOOP		0x32
+
+#define RK3568_PHYREG32				0x7C
+#define RK3568_PHYREG32_SSC_MASK		GENMASK(7, 4)
+#define RK3568_PHYREG32_SSC_DIR_MASK		GENMASK(5, 4)
+#define RK3568_PHYREG32_SSC_DIR_SHIFT		4
+#define RK3568_PHYREG32_SSC_UPWARD		0
+#define RK3568_PHYREG32_SSC_DOWNWARD		1
+#define RK3568_PHYREG32_SSC_OFFSET_MASK	GENMASK(7, 6)
+#define RK3568_PHYREG32_SSC_OFFSET_SHIFT	6
+#define RK3568_PHYREG32_SSC_OFFSET_500PPM	1
+
+#define RK3568_PHYREG33				0x80
+#define RK3568_PHYREG33_PLL_KVCO_MASK		GENMASK(4, 2)
+#define RK3568_PHYREG33_PLL_KVCO_SHIFT		2
Quoted 9 lines

drivers/phy/rockchip/phy-rockchip-naneng-combphy.c line 85

Quoted 6 lines
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +6 -0
+#define RK3568_PHYREG33_PLL_KVCO_VALUE		2
+#define RK3576_PHYREG33_PLL_KVCO_VALUE		4
+
+/* RK3588 COMBO PHY registers */
+#define RK3588_PHYREG27				0x6C
+#define RK3588_PHYREG27_RX_TRIM			0x4C

Would it be better if RK3588_PHYREG* comes after RK3576_PHYREG*?

Quoted 5 lines

It's intended to keep RK3576 definitions below RK3588 ones. The RK3576 driver makes use of a register introduced for RK3588 variant (RK3588_PHYREG27). Since similar reusing doesn't happen reversely, I consider the design of RK3576 a superset of the RK3588 one, and put RK3576 definitions later in the file.

Quoted 3 lines

I understand that logic, but OTOH in patch 4 you put the defines for RK3528 before RK3568. And RK3568 is not a superset of RK3528 AFAIK. It's just different?

Yes, they're completely different things. The order between RK3576 and RK3588 is decided within the RK3568-like variants. And as RK3528-like and RK3568-like combphys are completely different, they're simply sorted in alphabetical order.

Quoted 2 lines

That's why I think/thought sorting them (all) alphabetically would make more sense.

If putting RK3528 at first really confuses you, I'd like to add some extra comments to explicitly split these two kinds of register layouts apart and claim they aren't compatible. Although to me it's somehow obvious, as most definitions are prefixed with either RK3528 or RK3568.

Quoted 22 lines

My 0.02

Quoted 19 lines
Quoted 13 lines
Quoted 13 lines
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +12 -0
+
+/* RK3576 COMBO PHY registers */
+#define RK3576_PHYREG10				0x24
+#define RK3576_PHYREG10_SSC_PCM_MASK		GENMASK(3, 0)
+#define RK3576_PHYREG10_SSC_PCM_3500PPM		7
+
+#define RK3576_PHYREG17				0x40
+
+#define RK3576_PHYREG21				0x50
+#define RK3576_PHYREG21_RX_SQUELCH_VAL		0x0D
+
+#define RK3576_PHYREG30				0x74
Quoted 2 lines
Quoted 2 lines

struct rockchip_combphy_priv;
<snip>

Thanks,
Yao Zi

Best regards,
Yao Zi

#10 lore raw

Re: [PATCH v3 3/5] phy: rockchip: naneng-combphy: Add SoC prefix to register definitions

Quoted 4 lines · Yao Zi

If putting RK3528 at first really confuses you, I'd like to add some extra comments to explicitly split these two kinds of register layouts apart and claim they aren't compatible. Although to me it's somehow obvious, as most definitions are prefixed with either RK3528 or RK3568.

No need. This is just another PEBKAC issue.

Cheers,
Diederik

author
#11 lore raw

PATCH v3 4/5 phy: rockchip: naneng-combphy: Add RK3528 support

In reply to Yao Zi

Rockchip RK3528 integrates one naneng-combphy that is able to operate in PCIe and USB3 mode. The control logic is similar to previous variants of naneng-combphy but the register layout is apperantly different from the RK3568 one.

---
 .../rockchip/phy-rockchip-naneng-combphy.c    | 186 +++++++++++++++++-
 1 file changed, 185 insertions(+), 1 deletion(-)
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +185 -1
index 1d1c7723584b..bf00a85a113b 100644
@@ -20,7 +20,46 @@
 #define REF_CLOCK_25MHz			(25 * HZ_PER_MHZ)
 #define REF_CLOCK_100MHz		(100 * HZ_PER_MHZ)
 
-/* COMBO PHY REG */
+/* RK3528 COMBO PHY REG */
+#define RK3528_PHYREG6				0x18
+#define RK3528_PHYREG6_PLL_KVCO			GENMASK(12, 10)
+#define RK3528_PHYREG6_PLL_KVCO_VALUE		0x2
+#define RK3528_PHYREG6_SSC_DIR			GENMASK(5, 4)
+#define RK3528_PHYREG6_SSC_UPWARD		0
+#define RK3528_PHYREG6_SSC_DOWNWARD		1
+
+#define RK3528_PHYREG40				0x100
+#define RK3528_PHYREG40_SSC_EN			BIT(20)
+#define RK3528_PHYREG40_SSC_CNT			GENMASK(10, 0)
+#define RK3528_PHYREG40_SSC_CNT_VALUE		0x17d
+
+#define RK3528_PHYREG42				0x108
+#define RK3528_PHYREG42_CKDRV_CLK_SEL		BIT(29)
+#define RK3528_PHYREG42_CKDRV_CLK_PLL		0
+#define RK3528_PHYREG42_CKDRV_CLK_CKRCV		1
+#define RK3528_PHYREG42_PLL_LPF_R1_ADJ		GENMASK(10, 7)
+#define RK3528_PHYREG42_PLL_LPF_R1_ADJ_VALUE	0x9
+#define RK3528_PHYREG42_PLL_CHGPUMP_CUR_ADJ	GENMASK(6, 4)
+#define RK3528_PHYREG42_PLL_CHGPUMP_CUR_ADJ_VALUE 0x7
+#define RK3528_PHYREG42_PLL_KVCO_ADJ		GENMASK(2, 0)
+#define RK3528_PHYREG42_PLL_KVCO_ADJ_VALUE	0x0
+
+#define RK3528_PHYREG80				0x200
+#define RK3528_PHYREG80_CTLE_EN			BIT(17)
+
+#define RK3528_PHYREG81				0x204
+#define RK3528_PHYREG81_CDR_PHASE_PATH_GAIN_2X	BIT(5)
+#define RK3528_PHYREG81_SLEW_RATE_CTRL		GENMASK(2, 0)
+#define RK3528_PHYREG81_SLEW_RATE_CTRL_SLOW	0x7
+
+#define RK3528_PHYREG83				0x20c
+#define RK3528_PHYREG83_RX_SQUELCH		GENMASK(2, 0)
+#define RK3528_PHYREG83_RX_SQUELCH_VALUE	0x6
+
+#define RK3528_PHYREG86				0x218
+#define RK3528_PHYREG86_RTERM_DET_CLK_EN	BIT(14)
+
+/* RK3568 COMBO PHY REG */
 #define RK3568_PHYREG6				0x14
 #define RK3568_PHYREG6_PLL_DIV_MASK		GENMASK(7, 6)
 #define RK3568_PHYREG6_PLL_DIV_SHIFT		6
@@ -398,6 +437,147 @@ static int rockchip_combphy_probe(struct platform_device *pdev)
 	return PTR_ERR_OR_ZERO(phy_provider);
 }
 
+static int rk3528_combphy_cfg(struct rockchip_combphy_priv *priv)
+{
+	const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
+	unsigned long rate;
+	u32 val;
+
+	/* Set SSC downward spread spectrum */
+	val = FIELD_PREP(RK3528_PHYREG6_SSC_DIR, RK3528_PHYREG6_SSC_DOWNWARD);
+	rockchip_combphy_updatel(priv, RK3528_PHYREG6_SSC_DIR, val, RK3528_PHYREG6);
+
+	switch (priv->type) {
+	case PHY_TYPE_PCIE:
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_pcie, true);
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_pcie, true);
+		break;
+	case PHY_TYPE_USB3:
+		/* Enable adaptive CTLE for USB3.0 Rx */
+		rockchip_combphy_updatel(priv, RK3528_PHYREG80_CTLE_EN, RK3528_PHYREG80_CTLE_EN,
+					 RK3528_PHYREG80);
+
+		/* Set slow slew rate control for PI */
+		val = FIELD_PREP(RK3528_PHYREG81_SLEW_RATE_CTRL,
+				 RK3528_PHYREG81_SLEW_RATE_CTRL_SLOW);
+		rockchip_combphy_updatel(priv, RK3528_PHYREG81_SLEW_RATE_CTRL, val,
+					 RK3528_PHYREG81);
+
+		/* Set CDR phase path with 2x gain */
+		rockchip_combphy_updatel(priv, RK3528_PHYREG81_CDR_PHASE_PATH_GAIN_2X,
+					 RK3528_PHYREG81_CDR_PHASE_PATH_GAIN_2X, RK3528_PHYREG81);
+
+		/* Set Rx squelch input filler bandwidth */
+		val = FIELD_PREP(RK3528_PHYREG83_RX_SQUELCH, RK3528_PHYREG83_RX_SQUELCH_VALUE);
+		rockchip_combphy_updatel(priv, RK3528_PHYREG83_RX_SQUELCH, val, RK3528_PHYREG83);
+
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false);
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txelec_sel, false);
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->usb_mode_set, true);
+		break;
+	default:
+		dev_err(priv->dev, "incompatible PHY type\n");
+		return -EINVAL;
+	}
+
+	rate = clk_get_rate(priv->refclk);
+
+	switch (rate) {
+	case REF_CLOCK_24MHz:
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_24m, true);
+		if (priv->type == PHY_TYPE_USB3) {
+			/* Set ssc_cnt[10:0]=00101111101 & 31.5KHz */
+			val = FIELD_PREP(RK3528_PHYREG40_SSC_CNT, RK3528_PHYREG40_SSC_CNT_VALUE);
+			rockchip_combphy_updatel(priv, RK3528_PHYREG40_SSC_CNT, val,
+						 RK3528_PHYREG40);
+		} else if (priv->type == PHY_TYPE_PCIE) {
+			/* tx_trim[14]=1, Enable the counting clock of the rterm detect */
+			rockchip_combphy_updatel(priv, RK3528_PHYREG86_RTERM_DET_CLK_EN,
+						 RK3528_PHYREG86_RTERM_DET_CLK_EN, RK3528_PHYREG86);
+		}
+		break;
+	case REF_CLOCK_100MHz:
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_100m, true);
+		if (priv->type == PHY_TYPE_PCIE) {
+			/* PLL KVCO tuning fine */
+			val = FIELD_PREP(RK3528_PHYREG6_PLL_KVCO, RK3528_PHYREG6_PLL_KVCO_VALUE);
+			rockchip_combphy_updatel(priv, RK3528_PHYREG6_PLL_KVCO, val,
+						 RK3528_PHYREG6);
+
+			/* su_trim[6:4]=111, [10:7]=1001, [2:0]=000, swing 650mv */
+			writel(0x570804f0, priv->mmio + RK3528_PHYREG42);
+		}
+		break;
+	default:
+		dev_err(priv->dev, "Unsupported rate: %lu\n", rate);
+		return -EINVAL;
+	}
+
+	if (device_property_read_bool(priv->dev, "rockchip,ext-refclk")) {
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_ext, true);
+
+		if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) {
+			val = FIELD_PREP(RK3528_PHYREG42_CKDRV_CLK_SEL,
+					 RK3528_PHYREG42_CKDRV_CLK_CKRCV);
+			val |= FIELD_PREP(RK3528_PHYREG42_PLL_LPF_R1_ADJ,
+					  RK3528_PHYREG42_PLL_LPF_R1_ADJ_VALUE);
+			val |= FIELD_PREP(RK3528_PHYREG42_PLL_CHGPUMP_CUR_ADJ,
+					  RK3528_PHYREG42_PLL_CHGPUMP_CUR_ADJ_VALUE);
+			val |= FIELD_PREP(RK3528_PHYREG42_PLL_KVCO_ADJ,
+					  RK3528_PHYREG42_PLL_KVCO_ADJ_VALUE);
+			rockchip_combphy_updatel(priv,
+						 RK3528_PHYREG42_CKDRV_CLK_SEL		|
+						 RK3528_PHYREG42_PLL_LPF_R1_ADJ		|
+						 RK3528_PHYREG42_PLL_CHGPUMP_CUR_ADJ	|
+						 RK3528_PHYREG42_PLL_KVCO_ADJ,
+						 val, RK3528_PHYREG42);
+
+			val = FIELD_PREP(RK3528_PHYREG6_PLL_KVCO, RK3528_PHYREG6_PLL_KVCO_VALUE);
+			rockchip_combphy_updatel(priv, RK3528_PHYREG6_PLL_KVCO, val,
+						 RK3528_PHYREG6);
+		}
+	}
+
+	if (priv->type == PHY_TYPE_PCIE) {
+		if (device_property_read_bool(priv->dev, "rockchip,enable-ssc"))
+			rockchip_combphy_updatel(priv, RK3528_PHYREG40_SSC_EN,
+						 RK3528_PHYREG40_SSC_EN, RK3528_PHYREG40);
+	}
+
+	return 0;
+}
+
+static const struct rockchip_combphy_grfcfg rk3528_combphy_grfcfgs = {
+	/* pipe-phy-grf */
+	.pcie_mode_set		= { 0x0000, 5, 0, 0x00, 0x11 },
+	.usb_mode_set		= { 0x0000, 5, 0, 0x00, 0x04 },
+	.pipe_rxterm_set	= { 0x0000, 12, 12, 0x00, 0x01 },
+	.pipe_txelec_set	= { 0x0004, 1, 1, 0x00, 0x01 },
+	.pipe_txcomp_set	= { 0x0004, 4, 4, 0x00, 0x01 },
+	.pipe_clk_24m		= { 0x0004, 14, 13, 0x00, 0x00 },
+	.pipe_clk_100m		= { 0x0004, 14, 13, 0x00, 0x02 },
+	.pipe_rxterm_sel	= { 0x0008, 8, 8, 0x00, 0x01 },
+	.pipe_txelec_sel	= { 0x0008, 12, 12, 0x00, 0x01 },
+	.pipe_txcomp_sel	= { 0x0008, 15, 15, 0x00, 0x01 },
+	.pipe_clk_ext		= { 0x000c, 9, 8, 0x02, 0x01 },
+	.pipe_phy_status	= { 0x0034, 6, 6, 0x01, 0x00 },
+	.con0_for_pcie		= { 0x0000, 15, 0, 0x00, 0x110 },
+	.con1_for_pcie		= { 0x0004, 15, 0, 0x00, 0x00 },
+	.con2_for_pcie		= { 0x0008, 15, 0, 0x00, 0x101 },
+	.con3_for_pcie		= { 0x000c, 15, 0, 0x00, 0x0200 },
+};
+
+static const struct rockchip_combphy_cfg rk3528_combphy_cfgs = {
+	.num_phys	= 1,
+	.phy_ids	= {
+		0xffdc0000,
+	},
+	.grfcfg		= &rk3528_combphy_grfcfgs,
+	.combphy_cfg	= rk3528_combphy_cfg,
+};
+
 static int rk3562_combphy_cfg(struct rockchip_combphy_priv *priv)
 {
 	const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
@@ -1213,6 +1393,10 @@ static const struct rockchip_combphy_cfg rk3588_combphy_cfgs = {
 };
 
 static const struct of_device_id rockchip_combphy_of_match[] = {
+	{
+		.compatible = "rockchip,rk3528-naneng-combphy",
+		.data = &rk3528_combphy_cfgs,
+	},
 	{
 		.compatible = "rockchip,rk3562-naneng-combphy",
 		.data = &rk3562_combphy_cfgs,
Signature · 1 line
2.49.0
reviewer Reviewed-by on v3 4/5
#12 lore raw

Re: [PATCH v3 4/5] phy: rockchip: naneng-combphy: Add RK3528 support

Quoted 212 lines · Yao Zi

Rockchip RK3528 integrates one naneng-combphy that is able to operate in PCIe and USB3 mode. The control logic is similar to previous variants of naneng-combphy but the register layout is apperantly different from the RK3568 one.

---
  .../rockchip/phy-rockchip-naneng-combphy.c    | 186 +++++++++++++++++-
  1 file changed, 185 insertions(+), 1 deletion(-)
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +181 -1
index 1d1c7723584b..bf00a85a113b 100644
@@ -20,7 +20,46 @@
  #define REF_CLOCK_25MHz			(25 * HZ_PER_MHZ)
  #define REF_CLOCK_100MHz		(100 * HZ_PER_MHZ)
 
-/* COMBO PHY REG */
+/* RK3528 COMBO PHY REG */
+#define RK3528_PHYREG6				0x18
+#define RK3528_PHYREG6_PLL_KVCO			GENMASK(12, 10)
+#define RK3528_PHYREG6_PLL_KVCO_VALUE		0x2
+#define RK3528_PHYREG6_SSC_DIR			GENMASK(5, 4)
+#define RK3528_PHYREG6_SSC_UPWARD		0
+#define RK3528_PHYREG6_SSC_DOWNWARD		1
+
+#define RK3528_PHYREG40				0x100
+#define RK3528_PHYREG40_SSC_EN			BIT(20)
+#define RK3528_PHYREG40_SSC_CNT			GENMASK(10, 0)
+#define RK3528_PHYREG40_SSC_CNT_VALUE		0x17d
+
+#define RK3528_PHYREG42				0x108
+#define RK3528_PHYREG42_CKDRV_CLK_SEL		BIT(29)
+#define RK3528_PHYREG42_CKDRV_CLK_PLL		0
+#define RK3528_PHYREG42_CKDRV_CLK_CKRCV		1
+#define RK3528_PHYREG42_PLL_LPF_R1_ADJ		GENMASK(10, 7)
+#define RK3528_PHYREG42_PLL_LPF_R1_ADJ_VALUE	0x9
+#define RK3528_PHYREG42_PLL_CHGPUMP_CUR_ADJ	GENMASK(6, 4)
+#define RK3528_PHYREG42_PLL_CHGPUMP_CUR_ADJ_VALUE 0x7
+#define RK3528_PHYREG42_PLL_KVCO_ADJ		GENMASK(2, 0)
+#define RK3528_PHYREG42_PLL_KVCO_ADJ_VALUE	0x0
+
+#define RK3528_PHYREG80				0x200
+#define RK3528_PHYREG80_CTLE_EN			BIT(17)
+
+#define RK3528_PHYREG81				0x204
+#define RK3528_PHYREG81_CDR_PHASE_PATH_GAIN_2X	BIT(5)
+#define RK3528_PHYREG81_SLEW_RATE_CTRL		GENMASK(2, 0)
+#define RK3528_PHYREG81_SLEW_RATE_CTRL_SLOW	0x7
+
+#define RK3528_PHYREG83				0x20c
+#define RK3528_PHYREG83_RX_SQUELCH		GENMASK(2, 0)
+#define RK3528_PHYREG83_RX_SQUELCH_VALUE	0x6
+
+#define RK3528_PHYREG86				0x218
+#define RK3528_PHYREG86_RTERM_DET_CLK_EN	BIT(14)
+
+/* RK3568 COMBO PHY REG */
  #define RK3568_PHYREG6				0x14
  #define RK3568_PHYREG6_PLL_DIV_MASK		GENMASK(7, 6)
  #define RK3568_PHYREG6_PLL_DIV_SHIFT		6
@@ -398,6 +437,147 @@ static int rockchip_combphy_probe(struct platform_device *pdev)
  	return PTR_ERR_OR_ZERO(phy_provider);
  }
 
+static int rk3528_combphy_cfg(struct rockchip_combphy_priv *priv)
+{
+	const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
+	unsigned long rate;
+	u32 val;
+
+	/* Set SSC downward spread spectrum */
+	val = FIELD_PREP(RK3528_PHYREG6_SSC_DIR, RK3528_PHYREG6_SSC_DOWNWARD);
+	rockchip_combphy_updatel(priv, RK3528_PHYREG6_SSC_DIR, val, RK3528_PHYREG6);
+
+	switch (priv->type) {
+	case PHY_TYPE_PCIE:
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_pcie, true);
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_pcie, true);
+		break;
+	case PHY_TYPE_USB3:
+		/* Enable adaptive CTLE for USB3.0 Rx */
+		rockchip_combphy_updatel(priv, RK3528_PHYREG80_CTLE_EN, RK3528_PHYREG80_CTLE_EN,
+					 RK3528_PHYREG80);
+
+		/* Set slow slew rate control for PI */
+		val = FIELD_PREP(RK3528_PHYREG81_SLEW_RATE_CTRL,
+				 RK3528_PHYREG81_SLEW_RATE_CTRL_SLOW);
+		rockchip_combphy_updatel(priv, RK3528_PHYREG81_SLEW_RATE_CTRL, val,
+					 RK3528_PHYREG81);
+
+		/* Set CDR phase path with 2x gain */
+		rockchip_combphy_updatel(priv, RK3528_PHYREG81_CDR_PHASE_PATH_GAIN_2X,
+					 RK3528_PHYREG81_CDR_PHASE_PATH_GAIN_2X, RK3528_PHYREG81);
+
+		/* Set Rx squelch input filler bandwidth */
+		val = FIELD_PREP(RK3528_PHYREG83_RX_SQUELCH, RK3528_PHYREG83_RX_SQUELCH_VALUE);
+		rockchip_combphy_updatel(priv, RK3528_PHYREG83_RX_SQUELCH, val, RK3528_PHYREG83);
+
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txcomp_sel, false);
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_txelec_sel, false);
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->usb_mode_set, true);
+		break;
+	default:
+		dev_err(priv->dev, "incompatible PHY type\n");
+		return -EINVAL;
+	}
+
+	rate = clk_get_rate(priv->refclk);
+
+	switch (rate) {
+	case REF_CLOCK_24MHz:
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_24m, true);
+		if (priv->type == PHY_TYPE_USB3) {
+			/* Set ssc_cnt[10:0]=00101111101 & 31.5KHz */
+			val = FIELD_PREP(RK3528_PHYREG40_SSC_CNT, RK3528_PHYREG40_SSC_CNT_VALUE);
+			rockchip_combphy_updatel(priv, RK3528_PHYREG40_SSC_CNT, val,
+						 RK3528_PHYREG40);
+		} else if (priv->type == PHY_TYPE_PCIE) {
+			/* tx_trim[14]=1, Enable the counting clock of the rterm detect */
+			rockchip_combphy_updatel(priv, RK3528_PHYREG86_RTERM_DET_CLK_EN,
+						 RK3528_PHYREG86_RTERM_DET_CLK_EN, RK3528_PHYREG86);
+		}
+		break;
+	case REF_CLOCK_100MHz:
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_100m, true);
+		if (priv->type == PHY_TYPE_PCIE) {
+			/* PLL KVCO tuning fine */
+			val = FIELD_PREP(RK3528_PHYREG6_PLL_KVCO, RK3528_PHYREG6_PLL_KVCO_VALUE);
+			rockchip_combphy_updatel(priv, RK3528_PHYREG6_PLL_KVCO, val,
+						 RK3528_PHYREG6);
+
+			/* su_trim[6:4]=111, [10:7]=1001, [2:0]=000, swing 650mv */
+			writel(0x570804f0, priv->mmio + RK3528_PHYREG42);
+		}
+		break;
+	default:
+		dev_err(priv->dev, "Unsupported rate: %lu\n", rate);
+		return -EINVAL;
+	}
+
+	if (device_property_read_bool(priv->dev, "rockchip,ext-refclk")) {
+		rockchip_combphy_param_write(priv->phy_grf, &cfg->pipe_clk_ext, true);
+
+		if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_100MHz) {
+			val = FIELD_PREP(RK3528_PHYREG42_CKDRV_CLK_SEL,
+					 RK3528_PHYREG42_CKDRV_CLK_CKRCV);
+			val |= FIELD_PREP(RK3528_PHYREG42_PLL_LPF_R1_ADJ,
+					  RK3528_PHYREG42_PLL_LPF_R1_ADJ_VALUE);
+			val |= FIELD_PREP(RK3528_PHYREG42_PLL_CHGPUMP_CUR_ADJ,
+					  RK3528_PHYREG42_PLL_CHGPUMP_CUR_ADJ_VALUE);
+			val |= FIELD_PREP(RK3528_PHYREG42_PLL_KVCO_ADJ,
+					  RK3528_PHYREG42_PLL_KVCO_ADJ_VALUE);
+			rockchip_combphy_updatel(priv,
+						 RK3528_PHYREG42_CKDRV_CLK_SEL		|
+						 RK3528_PHYREG42_PLL_LPF_R1_ADJ		|
+						 RK3528_PHYREG42_PLL_CHGPUMP_CUR_ADJ	|
+						 RK3528_PHYREG42_PLL_KVCO_ADJ,
+						 val, RK3528_PHYREG42);
+
+			val = FIELD_PREP(RK3528_PHYREG6_PLL_KVCO, RK3528_PHYREG6_PLL_KVCO_VALUE);
+			rockchip_combphy_updatel(priv, RK3528_PHYREG6_PLL_KVCO, val,
+						 RK3528_PHYREG6);
+		}
+	}
+
+	if (priv->type == PHY_TYPE_PCIE) {
+		if (device_property_read_bool(priv->dev, "rockchip,enable-ssc"))
+			rockchip_combphy_updatel(priv, RK3528_PHYREG40_SSC_EN,
+						 RK3528_PHYREG40_SSC_EN, RK3528_PHYREG40);
+	}
+
+	return 0;
+}
+
+static const struct rockchip_combphy_grfcfg rk3528_combphy_grfcfgs = {
+	/* pipe-phy-grf */
+	.pcie_mode_set		= { 0x0000, 5, 0, 0x00, 0x11 },
+	.usb_mode_set		= { 0x0000, 5, 0, 0x00, 0x04 },
+	.pipe_rxterm_set	= { 0x0000, 12, 12, 0x00, 0x01 },
+	.pipe_txelec_set	= { 0x0004, 1, 1, 0x00, 0x01 },
+	.pipe_txcomp_set	= { 0x0004, 4, 4, 0x00, 0x01 },
+	.pipe_clk_24m		= { 0x0004, 14, 13, 0x00, 0x00 },
+	.pipe_clk_100m		= { 0x0004, 14, 13, 0x00, 0x02 },
+	.pipe_rxterm_sel	= { 0x0008, 8, 8, 0x00, 0x01 },
+	.pipe_txelec_sel	= { 0x0008, 12, 12, 0x00, 0x01 },
+	.pipe_txcomp_sel	= { 0x0008, 15, 15, 0x00, 0x01 },
+	.pipe_clk_ext		= { 0x000c, 9, 8, 0x02, 0x01 },
+	.pipe_phy_status	= { 0x0034, 6, 6, 0x01, 0x00 },
+	.con0_for_pcie		= { 0x0000, 15, 0, 0x00, 0x110 },
+	.con1_for_pcie		= { 0x0004, 15, 0, 0x00, 0x00 },
+	.con2_for_pcie		= { 0x0008, 15, 0, 0x00, 0x101 },
+	.con3_for_pcie		= { 0x000c, 15, 0, 0x00, 0x0200 },
+};
+
+static const struct rockchip_combphy_cfg rk3528_combphy_cfgs = {
+	.num_phys	= 1,
+	.phy_ids	= {
+		0xffdc0000,
+	},
+	.grfcfg		= &rk3528_combphy_grfcfgs,
+	.combphy_cfg	= rk3528_combphy_cfg,
+};
+
  static int rk3562_combphy_cfg(struct rockchip_combphy_priv *priv)
  {
  	const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;

drivers/phy/rockchip/phy-rockchip-naneng-combphy.c static const struct rockchip_combphy_cfg rk3588_combphy_cfgs = { · line 1402

Quoted 10 lines
drivers/phy/rockchip/phy-rockchip-naneng-combphy.c +4 -0
@@ -1213,6 +1393,10 @@ static const struct rockchip_combphy_cfg rk3588_combphy_cfgs = {
  };
 
  static const struct of_device_id rockchip_combphy_of_match[] = {
+	{
+		.compatible = "rockchip,rk3528-naneng-combphy",
+		.data = &rk3528_combphy_cfgs,
+	},
  	{
  		.compatible = "rockchip,rk3562-naneng-combphy",
  		.data = &rk3562_combphy_cfgs,
author
#13 lore raw

PATCH v3 5/5 arm64: dts: rockchip: Add naneng-combphy for RK3528

In reply to Yao Zi

Rockchip RK3528 ships a naneng-combphy that is shared by PCIe and USB 3.0 controllers. Describe it and the pipe-phy grf which it depends on.

---
 arch/arm64/boot/dts/rockchip/rk3528.dtsi | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)
arch/arm64/boot/dts/rockchip/rk3528.dtsi +22 -0
index b2724c969a76..314afb94e19b 100644
@@ -318,6 +318,11 @@ vpu_grf: syscon@ff340000 {
 			reg = <0x0 0xff340000 0x0 0x8000>;
 		};
 
+		pipe_phy_grf: syscon@ff348000 {
+			compatible = "rockchip,rk3528-pipe-phy-grf", "syscon";
+			reg = <0x0 0xff348000 0x0 0x8000>;
+		};
+
 		vo_grf: syscon@ff360000 {
 			compatible = "rockchip,rk3528-vo-grf", "syscon";
 			reg = <0x0 0xff360000 0x0 0x10000>;
@@ -867,6 +872,23 @@ dmac: dma-controller@ffd60000 {
 			arm,pl330-periph-burst;
 		};
 
+		combphy: phy@ffdc0000 {
+			compatible = "rockchip,rk3528-naneng-combphy";
+			reg = <0x0 0xffdc0000 0x0 0x10000>;
+			#phy-cells = <1>;
+			clocks = <&cru CLK_REF_PCIE_INNER_PHY>, <&cru PCLK_PCIE_PHY>,
+				 <&cru PCLK_PIPE_GRF>;
+			clock-names = "ref", "apb",
+				      "pipe";
+			assigned-clocks = <&cru CLK_REF_PCIE_INNER_PHY>;
+			assigned-clock-rates = <100000000>;
+			resets = <&cru SRST_PCIE_PIPE_PHY>, <&cru SRST_P_PCIE_PHY>;
+			reset-names = "phy", "apb";
+			rockchip,pipe-grf = <&vpu_grf>;
+			rockchip,pipe-phy-grf = <&pipe_phy_grf>;
+			status = "disabled";
+		};
+
 		pinctrl: pinctrl {
 			compatible = "rockchip,rk3528-pinctrl";
 			rockchip,grf = <&ioc_grf>;
Signature · 1 line
2.49.0
#14 lore raw

Re: [PATCH v3 5/5] arm64: dts: rockchip: Add naneng-combphy for RK3528

Quoted 25 lines · Yao Zi

Rockchip RK3528 ships a naneng-combphy that is shared by PCIe and USB 3.0 controllers. Describe it and the pipe-phy grf which it depends on.

---
 arch/arm64/boot/dts/rockchip/rk3528.dtsi | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)
arch/arm64/boot/dts/rockchip/rk3528.dtsi +5 -0
index b2724c969a76..314afb94e19b 100644
@@ -318,6 +318,11 @@ vpu_grf: syscon@ff340000 {
 			reg = <0x0 0xff340000 0x0 0x8000>;
 		};
 
+		pipe_phy_grf: syscon@ff348000 {
+			compatible = "rockchip,rk3528-pipe-phy-grf", "syscon";
+			reg = <0x0 0xff348000 0x0 0x8000>;
+		};
+
 		vo_grf: syscon@ff360000 {
 			compatible = "rockchip,rk3528-vo-grf", "syscon";
 			reg = <0x0 0xff360000 0x0 0x10000>;

arch/arm64/boot/dts/rockchip/rk3528.dtsi dmac: dma-controller@ffd60000 { · line 878

Quoted 7 lines
arch/arm64/boot/dts/rockchip/rk3528.dtsi +4 -0
@@ -867,6 +872,23 @@ dmac: dma-controller@ffd60000 {
 			arm,pl330-periph-burst;
 		};
 
+		combphy: phy@ffdc0000 {
+			compatible = "rockchip,rk3528-naneng-combphy";
+			reg = <0x0 0xffdc0000 0x0 0x10000>;
+			#phy-cells = <1>;

Should probably be sorted at end or before resets prop.

arch/arm64/boot/dts/rockchip/rk3528.dtsi dmac: dma-controller@ffd60000 { · line 879

Quoted 1 line
arch/arm64/boot/dts/rockchip/rk3528.dtsi +1 -0
+			clocks = <&cru CLK_REF_PCIE_INNER_PHY>, <&cru PCLK_PCIE_PHY>,

This break the ~80 line length limit mostly kept in this file.

arch/arm64/boot/dts/rockchip/rk3528.dtsi dmac: dma-controller@ffd60000 { · line 882

Quoted 3 lines
arch/arm64/boot/dts/rockchip/rk3528.dtsi +3 -0
+				 <&cru PCLK_PIPE_GRF>;
+			clock-names = "ref", "apb",
+				      "pipe";

Could be kept on a single line.

arch/arm64/boot/dts/rockchip/rk3528.dtsi dmac: dma-controller@ffd60000 { · line 884

Quoted 2 lines
arch/arm64/boot/dts/rockchip/rk3528.dtsi +2 -0
+			assigned-clocks = <&cru CLK_REF_PCIE_INNER_PHY>;
+			assigned-clock-rates = <100000000>;

Other assigned-clock props are sorted before clocks props in this file.

This is also missing power-domains information (also missing from dt-bindings patch):

	power-domains = <&power RK3528_PD_VPU>;

arch/arm64/boot/dts/rockchip/rk3528.dtsi dmac: dma-controller@ffd60000 { · line 885

Quoted 1 line
arch/arm64/boot/dts/rockchip/rk3528.dtsi +1 -0
+			resets = <&cru SRST_PCIE_PIPE_PHY>, <&cru SRST_P_PCIE_PHY>;

This also break the ~80 line length limit mostly kept in this file.

Regards,
Jonas

Quoted 9 lines
arch/arm64/boot/dts/rockchip/rk3528.dtsi +6 -0
+			reset-names = "phy", "apb";
+			rockchip,pipe-grf = <&vpu_grf>;
+			rockchip,pipe-phy-grf = <&pipe_phy_grf>;
+			status = "disabled";
+		};
+
 		pinctrl: pinctrl {
 			compatible = "rockchip,rk3528-pinctrl";
 			rockchip,grf = <&ioc_grf>;
author
#15 lore raw

Re: [PATCH v3 5/5] arm64: dts: rockchip: Add naneng-combphy for RK3528

Quoted 29 lines · Jonas Karlman
Quoted 28 lines · Yao Zi

Rockchip RK3528 ships a naneng-combphy that is shared by PCIe and USB 3.0 controllers. Describe it and the pipe-phy grf which it depends on.

---
 arch/arm64/boot/dts/rockchip/rk3528.dtsi | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)
arch/arm64/boot/dts/rockchip/rk3528.dtsi +5 -0
index b2724c969a76..314afb94e19b 100644
@@ -318,6 +318,11 @@ vpu_grf: syscon@ff340000 {
 			reg = <0x0 0xff340000 0x0 0x8000>;
 		};
 
+		pipe_phy_grf: syscon@ff348000 {
+			compatible = "rockchip,rk3528-pipe-phy-grf", "syscon";
+			reg = <0x0 0xff348000 0x0 0x8000>;
+		};
+
 		vo_grf: syscon@ff360000 {
 			compatible = "rockchip,rk3528-vo-grf", "syscon";
 			reg = <0x0 0xff360000 0x0 0x10000>;
@@ -867,6 +872,23 @@ dmac: dma-controller@ffd60000 {
 			arm,pl330-periph-burst;
 		};
 
Quoted 6 lines

arch/arm64/boot/dts/rockchip/rk3528.dtsi dmac: dma-controller@ffd60000 { · line 878

Quoted 4 lines
arch/arm64/boot/dts/rockchip/rk3528.dtsi +4 -0
+		combphy: phy@ffdc0000 {
+			compatible = "rockchip,rk3528-naneng-combphy";
+			reg = <0x0 0xffdc0000 0x0 0x10000>;
+			#phy-cells = <1>;

Should probably be sorted at end or before resets prop.

Will sort the properties.

Quoted 3 lines

arch/arm64/boot/dts/rockchip/rk3528.dtsi dmac: dma-controller@ffd60000 { · line 879

Quoted 2 lines
arch/arm64/boot/dts/rockchip/rk3528.dtsi +1 -0
+			clocks = <&cru CLK_REF_PCIE_INNER_PHY>, <&cru PCLK_PCIE_PHY>,

This break the ~80 line length limit mostly kept in this file.

Oops, I didn't notice it. Will split them into lines.

Quoted 11 lines

arch/arm64/boot/dts/rockchip/rk3528.dtsi dmac: dma-controller@ffd60000 { · line 882

Quoted 3 lines
arch/arm64/boot/dts/rockchip/rk3528.dtsi +3 -0
+				 <&cru PCLK_PIPE_GRF>;
+			clock-names = "ref", "apb",
+				      "pipe";

Could be kept on a single line.

arch/arm64/boot/dts/rockchip/rk3528.dtsi dmac: dma-controller@ffd60000 { · line 884

Quoted 2 lines
arch/arm64/boot/dts/rockchip/rk3528.dtsi +2 -0
+			assigned-clocks = <&cru CLK_REF_PCIE_INNER_PHY>;
+			assigned-clock-rates = <100000000>;

Other assigned-clock props are sorted before clocks props in this file.

Quoted 4 lines

This is also missing power-domains information (also missing from dt-bindings patch):

	power-domains = <&power RK3528_PD_VPU>;

I didn't expect your power-domain series when writing v1, thanks for the reminder.

As the power-domain series just came out, I'd like to wait until it merges and then work further on RK3528 support for naneng-combphy.

I'm not sure whether it's possible to get the combphy cleanup patch (3th in this series) merged first. It should be ready for merging and I think this may avoid possible conflicts in the future, Any suggestions will be appreciated.

Quoted 3 lines

arch/arm64/boot/dts/rockchip/rk3528.dtsi dmac: dma-controller@ffd60000 { · line 885

Quoted 1 line
arch/arm64/boot/dts/rockchip/rk3528.dtsi +1 -0
+			resets = <&cru SRST_PCIE_PIPE_PHY>, <&cru SRST_P_PCIE_PHY>;

This also break the ~80 line length limit mostly kept in this file.

I'm willing to keep the ~80 limit and will split the line.

Quoted 13 lines

Regards,
Jonas

arch/arm64/boot/dts/rockchip/rk3528.dtsi dmac: dma-controller@ffd60000 { · line 894

Quoted 9 lines
arch/arm64/boot/dts/rockchip/rk3528.dtsi +6 -0
+			reset-names = "phy", "apb";
+			rockchip,pipe-grf = <&vpu_grf>;
+			rockchip,pipe-phy-grf = <&pipe_phy_grf>;
+			status = "disabled";
+		};
+
 		pinctrl: pinctrl {
 			compatible = "rockchip,rk3528-pinctrl";
 			rockchip,grf = <&ioc_grf>;

Best regards,
Yao Zi