wifi: ath9k: add ahb OF support
Subsystems (4)
v4 cover wifi: ath9k: add ahb OF support
First two commits are small cleanups to make the changes of the third simpler. The fourth actually adds dts definitions to use ahb.
v2: Add documentation, use kernel_ulong_t, and of_device_get_match_data
v3: Use qcom prefix and wifi suffix as in other ath drivers.
v4: fix up dts example in Documentation
Rosen Penev (5):
wifi: ath9k: ahb: reorder declarations
wifi: ath9k: ahb: reorder includes
wifi: ath9k: ahb: replace id_table with of
dt-bindings: net: wireless: ath9k: add OF bindings
mips: dts: qca: add wmac support
.../bindings/net/wireless/qca,ath9k.yaml | 23 ++++++- arch/mips/boot/dts/qca/ar9132.dtsi | 9 +++ .../boot/dts/qca/ar9132_tl_wr1043nd_v1.dts | 4 ++ arch/mips/boot/dts/qca/ar9331.dtsi | 9 +++ arch/mips/boot/dts/qca/ar9331_dpt_module.dts | 4 ++ .../mips/boot/dts/qca/ar9331_dragino_ms14.dts | 4 ++ arch/mips/boot/dts/qca/ar9331_omega.dts | 4 ++ .../qca/ar9331_openembed_som9331_board.dts | 4 ++ arch/mips/boot/dts/qca/ar9331_tl_mr3020.dts | 4 ++ drivers/net/wireless/ath/ath9k/ahb.c | 60 +++++++------------ 10 files changed, 84 insertions(+), 41 deletions(-)
Signature · 1 line
2.49.0
PATCH v4 1/5 wifi: ath9k: ahb: reorder declarations
Easier to look at. Follows netdev style.
Also remove ret assignment. Because of all of these devm conversions, ret = 0 is a path that never gets hit. The first time it does it when request_irq fails, but that ends up reassigning it.
--- drivers/net/wireless/ath/ath9k/ahb.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-)
drivers/net/wireless/ath/ath9k/ahb.c +5 -5
@@ -71,14 +71,14 @@ static const struct ath_bus_ops ath_ahb_bus_ops = {static int ath_ahb_probe (struct platform_device *pdev) { -void __iomem *mem; -struct ath_softc *sc; -struct ieee80211_hw *hw;const struct platform_device_id *id =platform_get_device_id (pdev); -int irq; -int ret =0 ; +struct ieee80211_hw *hw; +struct ath_softc *sc;struct ath_hw *ah; +void __iomem *mem;char hw_name[64 ]; +int irq; +int ret;if (!dev_get_platdata (&pdev->dev)) {dev_err (&pdev->dev,"no platform data specified\n" );
Signature · 1 line
2.49.0
Re: [PATCHv4 1/5] wifi: ath9k: ahb: reorder declarations
Quoted 8 lines · Rosen Penev
Easier to look at. Follows netdev style.
Also remove ret assignment. Because of all of these devm conversions, ret = 0 is a path that never gets hit. The first time it does it when
request_irqfails, but that ends up reassigning it.Signed-off-by Rosen Penev <[email protected]>---
Best regards,
Krzysztof
PATCH v4 2/5 wifi: ath9k: ahb: reorder includes
In reply to Rosen PenevAlphabetic includes are easier to look at and to make further changes to them.
--- drivers/net/wireless/ath/ath9k/ahb.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/net/wireless/ath/ath9k/ahb.c +3 -2
@@ -16,10 +16,11 @@* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. */ +#include <linux/mod_devicetable.h> +#include <linux/module.h> #include <linux/nl80211.h> #include <linux/platform_device.h> -#include <linux/module.h> -#include <linux/mod_devicetable.h> +#include "ath9k.h" static const struct platform_device_id ath9k_platform_id_table[] = {
Signature · 1 line
2.49.0
Re: [PATCHv4 2/5] wifi: ath9k: ahb: reorder includes
Quoted 5 lines · Rosen Penev
Alphabetic includes are easier to look at and to make further changes to them.
Signed-off-by Rosen Penev <[email protected]>---
Best regards,
Krzysztof
PATCH v4 3/5 dt-bindings: net: wireless: ath9k: add WIFI bindings
In reply to Rosen PenevThese are for the wireless chips that come built in with various Atheros/QCA SoCs. dts wise, the difference between pcie and the wmac is
AHB > PCIE > WIFI
AHB > WIFI
These will be used to replace the platform_device code with OF in the following patch.
--- .../bindings/net/wireless/qca,ath9k.yaml | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml +17 -1
@@ -12,7 +12,7 @@ maintainers: description: | This node provides properties for configuring the ath9k wireless device. The node is expected to be specified as a child node of the PCI controller - to which the wireless chip is connected. + or AHB bus to which the wireless chip is connected. allOf: - $ref: ieee80211.yaml#
@@ -35,6 +35,12 @@ properties: - pci168c,0034 # AR9462 - pci168c,0036 # AR9565 - pci168c,0037 # AR1111 and AR9485 + - qcom,ar9130-wifi + - qcom,ar9330-wifi + - qcom,ar9340-wifi + - qcom,qca9530-wifi + - qcom,qca9550-wifi + - qcom,qca9560-wifi reg: maxItems: 1
@@ -88,3 +94,13 @@ examples: nvmem-cell-names = "mac-address", "calibration"; }; }; + - | + ahb { + #address-cells = <1>; + #size-cells = <1>; + wifi@180c0000 { + compatible = "qcom,ar9130-wifi"; + reg = <0x180c0000 0x230000>; + interrupts = <2>; + }; + };
Signature · 1 line
2.49.0
Re: [PATCHv4 3/5] dt-bindings: net: wireless: ath9k: add WIFI bindings
Quoted 8 lines · Rosen Penev
These are for the wireless chips that come built in with various Atheros/QCA SoCs. dts wise, the difference between pcie and the wmac is
AHB > PCIE > WIFI
AHB > WIFIThese will be used to replace the
platform_devicecode with OF in the following patch.
Drop the sentence. If we use auxiliary driver instead, should it invalidate this commit msg?
Quoted 20 lines
Signed-off-by Rosen Penev <[email protected]>--- .../bindings/net/wireless/qca,ath9k.yaml | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-)Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml +1
-1@@ -12,7 +12,7 @@ maintainers: description: | This node provides properties for configuring the ath9k wireless device. The node is expected to be specified as a child node of the PCI controller - to which the wireless chip is connected. + or AHB bus to which the wireless chip is connected. allOf: - $ref: ieee80211.yaml#
Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml properties: · line 40
Quoted 6 lines
Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml +3
-0@@ -35,6 +35,12 @@ properties: - pci168c,0034 # AR9462 - pci168c,0036 # AR9565 - pci168c,0037 # AR1111 and AR9485 + - qcom,ar9130-wifi + - qcom,ar9330-wifi + - qcom,ar9340-wifi
I assume all these qr9xxx are capable of running Linux, thus you document here other side - having them as part of other SoC.
Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml properties: · line 43
Quoted 3 lines
Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml +3
-0+ - qcom,qca9530-wifi + - qcom,qca9550-wifi + - qcom,qca9560-wifi
But what about these? As well? Do they have other interfaces? IOW, suffix "-wifi" is added ONLY if there is "qcom,qca9530" or "qcom,qca9530-foo" somewhere or possible.
Best regards,
Krzysztof
Re: [PATCHv4 3/5] dt-bindings: net: wireless: ath9k: add WIFI bindings
Quoted 5 lines · Krzysztof Kozlowski
Quoted 3 lines · Rosen Penev
These are for the wireless chips that come built in with various Atheros/QCA SoCs. dts wise, the difference between pcie and the wmac is
Quoted 8 lines
Quoted 5 lines
AHB > PCIE > WIFI
AHB > WIFIThese will be used to replace the
platform_devicecode with OF in the following patch.Drop the sentence. If we use auxiliary driver instead, should it invalidate this commit msg?
Will drop.
Quoted 18 lines
Quoted 18 lines
Signed-off-by Rosen Penev <[email protected]>--- .../bindings/net/wireless/qca,ath9k.yaml | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-)Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml +1
-1@@ -12,7 +12,7 @@ maintainers: description: | This node provides properties for configuring the ath9k wireless device. The node is expected to be specified as a child node of the PCI controller - to which the wireless chip is connected. + or AHB bus to which the wireless chip is connected.
Quoted 12 lines
Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml properties: · line 40
Quoted 9 lines
Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml +3
-0allOf: - $ref: ieee80211.yaml#@@ -35,6 +35,12 @@ properties: - pci168c,0034 # AR9462 - pci168c,0036 # AR9565 - pci168c,0037 # AR1111 and AR9485 + - qcom,ar9130-wifi + - qcom,ar9330-wifi + - qcom,ar9340-wifiI assume all these qr9xxx are capable of running Linux, thus you document here other side - having them as part of other SoC.
I assume you're referring to Documentation/devicetree/bindings/mips/ath79-soc.txt
Quoted 8 lines
Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml properties: · line 43
Quoted 4 lines
Documentation/devicetree/bindings/net/wireless/qca,ath9k.yaml +3
-0+ - qcom,qca9530-wifi + - qcom,qca9550-wifi + - qcom,qca9560-wifiBut what about these? As well? Do they have other interfaces? IOW, suffix "-wifi" is added ONLY if there is "qcom,qca9530" or "qcom,qca9530-foo" somewhere or possible.
They do. An example being the ar71xx driver which has
- qca,ar9130-eth # Atheros AR9130
- qca,ar9330-eth # Atheros AR9330
- qca,ar9340-eth # Atheros AR9340
- qca,qca9530-eth # Qualcomm Atheros QCA9530
- qca,qca9550-eth # Qualcomm Atheros QCA9550
- qca,qca9560-eth # Qualcomm Atheros QCA9560I was advised earlier to change it to qcom instead of qca. Qualcomm itself uses the qcom, prefix for its maintained drivers while the non Qualcomm maintained stuff uses qca.
Quoted 4 lines
Best regards,
Krzysztof
Re: [PATCHv4 3/5] dt-bindings: net: wireless: ath9k: add WIFI bindings
In reply to Rosen PenevQuoted 9 lines · Rosen Penev
These are for the wireless chips that come built in with various Atheros/QCA SoCs. dts wise, the difference between pcie and the wmac is
AHB > PCIE > WIFI
AHB > WIFIThese will be used to replace the
platform_devicecode with OF in the following patch.
Best regards,
Krzysztof
PATCH v4 4/5 wifi: ath9k: ahb: replace id_table with of
In reply to Rosen PenevSince 2b0996c7646 , all of this platform code became no-op with no OF replacement. Not only that, there are no users of AHB here. Add an OF match table that mostly mirrors the original platform device id table. Use a qca prefix as is done for the only other property: qca,no-eeprom. Also used qca prefix for ar9530 as the latter seems to be a mistake.
This will be used to add ath9k support for the various ath79 devices here.
--- drivers/net/wireless/ath/ath9k/ahb.c | 47 ++++++++-------------------- 1 file changed, 13 insertions(+), 34 deletions(-)
drivers/net/wireless/ath/ath9k/ahb.c +13 -34
@@ -19,35 +19,18 @@#include <linux/mod_devicetable.h> #include <linux/module.h> #include <linux/nl80211.h> +#include <linux/of.h> #include <linux/platform_device.h> #include "ath9k.h" -static const struct platform_device_id ath9k_platform_id_table[] = { - { - .name ="ath9k" , - .driver_data =AR5416_AR9100_DEVID , - }, - { - .name ="ar933x_wmac" , - .driver_data =AR9300_DEVID_AR9330 , - }, - { - .name ="ar934x_wmac" , - .driver_data =AR9300_DEVID_AR9340 , - }, - { - .name ="qca955x_wmac" , - .driver_data =AR9300_DEVID_QCA955X , - }, - { - .name ="qca953x_wmac" , - .driver_data =AR9300_DEVID_AR953X , - }, - { - .name ="qca956x_wmac" , - .driver_data =AR9300_DEVID_QCA956X , - }, +static const struct of_device_id ath9k_of_match_table[] = { + { .compatible ="qcom,ar9130-wifi" , .data = (void *)AR5416_AR9100_DEVID }, + { .compatible ="qcom,ar9330-wifi" , .data = (void *)AR9300_DEVID_AR9330 }, + { .compatible ="qcom,ar9340-wifi" , .data = (void *)AR9300_DEVID_AR9340 }, + { .compatible ="qcom,qca9530-wifi" , .data = (void *)AR9300_DEVID_AR953X }, + { .compatible ="qcom,qca9550-wifi" , .data = (void *)AR9300_DEVID_QCA955X }, + { .compatible ="qcom,qca9560-wifi" , .data = (void *)AR9300_DEVID_QCA956X }, {}, };
@@ -72,20 +55,15 @@ static const struct ath_bus_ops ath_ahb_bus_ops = {static int ath_ahb_probe (struct platform_device *pdev) { -const struct platform_device_id *id =platform_get_device_id (pdev);struct ieee80211_hw *hw;struct ath_softc *sc;struct ath_hw *ah;void __iomem *mem;char hw_name[64 ]; +u16 dev_id;int irq;int ret; -if (!dev_get_platdata (&pdev->dev)) { -dev_err (&pdev->dev,"no platform data specified\n" ); -return -EINVAL ; - } - mem =devm_platform_ioremap_resource (pdev,0 );if (IS_ERR (mem)) {dev_err (&pdev->dev,"ioremap failed\n" );
@@ -118,7 +96,8 @@ static int ath_ahb_probe(struct platform_device *pdev) goto err_free_hw; } - ret =ath9k_init_device (id->driver_data, sc, &ath_ahb_bus_ops); + dev_id = (u16 )(kernel_ulong_t )of_device_get_match_data (&pdev->dev); + ret =ath9k_init_device (dev_id, sc, &ath_ahb_bus_ops);if (ret) {dev_err (&pdev->dev,"failed to initialize device\n" ); goto err_irq;
@@ -156,11 +135,11 @@ static struct platform_driver ath_ahb_driver = { .remove = ath_ahb_remove, .driver = { .name = "ath9k", + .of_match_table = ath9k_of_match_table, }, - .id_table = ath9k_platform_id_table, }; -MODULE_DEVICE_TABLE (platform, ath9k_platform_id_table); +MODULE_DEVICE_TABLE (of, ath9k_of_match_table);int ath_ahb_init (void ) {
Signature · 1 line
2.49.0
Re: [PATCHv4 4/5] wifi: ath9k: ahb: replace id_table with of
drivers/net/wireless/ath/ath9k/ahb.c static const struct ath_bus_ops ath_ahb_bus_ops = { · line 63
Quoted 11 lines · Rosen Penev
drivers/net/wireless/ath/ath9k/ahb.c +1
-1@@ -72,20 +55,15 @@ static const struct ath_bus_ops ath_ahb_bus_ops = {static int ath_ahb_probe (struct platform_device *pdev) { -const struct platform_device_id *id =platform_get_device_id (pdev);struct ieee80211_hw *hw;struct ath_softc *sc;struct ath_hw *ah;void __iomem *mem;char hw_name[64 ]; +u16 dev_id;
I don't think these are u16 in the headers, but unsigned int.
Quoted 12 lines
drivers/net/wireless/ath/ath9k/ahb.c +0
-5int irq;int ret; -if (!dev_get_platdata (&pdev->dev)) { -dev_err (&pdev->dev,"no platform data specified\n" ); -return -EINVAL ; - } - mem =devm_platform_ioremap_resource (pdev,0 );if (IS_ERR (mem)) {dev_err (&pdev->dev,"ioremap failed\n" );
drivers/net/wireless/ath/ath9k/ahb.c static int ath_ahb_probe(struct platform_device *pdev) · line 99
Quoted 5 lines
drivers/net/wireless/ath/ath9k/ahb.c +1
-1@@ -118,7 +96,8 @@ static int ath_ahb_probe(struct platform_device *pdev) goto err_free_hw; } - ret =ath9k_init_device (id->driver_data, sc, &ath_ahb_bus_ops); + dev_id = (u16 )(kernel_ulong_t )of_device_get_match_data (&pdev->dev);
u16 cast looks not needed.
drivers/net/wireless/ath/ath9k/ahb.c static int ath_ahb_probe(struct platform_device *pdev) · line 103
Quoted 4 lines
drivers/net/wireless/ath/ath9k/ahb.c +1
-0+ ret =ath9k_init_device (dev_id, sc, &ath_ahb_bus_ops);if (ret) {dev_err (&pdev->dev,"failed to initialize device\n" ); goto err_irq;
Best regards,
Krzysztof
Re: [PATCHv4 4/5] wifi: ath9k: ahb: replace id_table with of
Quoted 4 lines · Krzysztof Kozlowski
Quoted 2 lines · Rosen Penev
(quoted diff) +0
-0@@ -72,20 +55,15 @@ static const struct ath_bus_ops ath_ahb_bus_ops = {
Quoted 11 lines
drivers/net/wireless/ath/ath9k/ahb.c static const struct ath_bus_ops ath_ahb_bus_ops = { · line 63
Quoted 9 lines
drivers/net/wireless/ath/ath9k/ahb.c +1
-1static int ath_ahb_probe (struct platform_device *pdev) { -const struct platform_device_id *id =platform_get_device_id (pdev);struct ieee80211_hw *hw;struct ath_softc *sc;struct ath_hw *ah;void __iomem *mem;char hw_name[64 ]; +u16 dev_id;I don't think these are u16 in the headers, but unsigned int.
Sure. I can change to int or kernel_ulong_t. It doesn't matter much. The function that uses this has an int parameter, so might make sense to use that.
Quoted 16 lines
Quoted 16 lines
drivers/net/wireless/ath/ath9k/ahb.c +0
-5int irq;int ret; -if (!dev_get_platdata (&pdev->dev)) { -dev_err (&pdev->dev,"no platform data specified\n" ); -return -EINVAL ; - } - mem =devm_platform_ioremap_resource (pdev,0 );if (IS_ERR (mem)) {dev_err (&pdev->dev,"ioremap failed\n" );@@ -118,7 +96,8 @@ static int ath_ahb_probe(struct platform_device *pdev) goto err_free_hw; }
Quoted 4 lines
drivers/net/wireless/ath/ath9k/ahb.c static int ath_ahb_probe(struct platform_device *pdev) · line 99
Quoted 2 lines
drivers/net/wireless/ath/ath9k/ahb.c +1
-1- ret =ath9k_init_device (id->driver_data, sc, &ath_ahb_bus_ops); + dev_id = (u16 )(kernel_ulong_t )of_device_get_match_data (&pdev->dev);u16 cast looks not needed.
Correct. It's placed for extra clarity, although probably not needed.
Quoted 8 lines
drivers/net/wireless/ath/ath9k/ahb.c static int ath_ahb_probe(struct platform_device *pdev) · line 103
Quoted 6 lines
drivers/net/wireless/ath/ath9k/ahb.c +1
-0+ ret =ath9k_init_device (dev_id, sc, &ath_ahb_bus_ops);if (ret) {dev_err (&pdev->dev,"failed to initialize device\n" ); goto err_irq;Best regards,
Krzysztof
Re: [PATCHv4 4/5] wifi: ath9k: ahb: replace id_table with of
Quoted 16 lines · Rosen Penev
Quoted 4 lines · Krzysztof Kozlowski
Quoted 2 lines · Rosen Penev
(quoted diff) +0
-0@@ -72,20 +55,15 @@ static const struct ath_bus_ops ath_ahb_bus_ops = {Quoted 11 lines
drivers/net/wireless/ath/ath9k/ahb.c static const struct ath_bus_ops ath_ahb_bus_ops = { · line 63
Quoted 9 lines
drivers/net/wireless/ath/ath9k/ahb.c +1
-1static int ath_ahb_probe (struct platform_device *pdev) { -const struct platform_device_id *id =platform_get_device_id (pdev);struct ieee80211_hw *hw;struct ath_softc *sc;struct ath_hw *ah;void __iomem *mem;char hw_name[64 ]; +u16 dev_id;I don't think these are u16 in the headers, but unsigned int.
Quoted 3 lines
Sure. I can change to int or
kernel_ulong_t. It doesn't matter much. The function that uses this has an int parameter, so might make sense to use that.
Ah, ok, that's fine then. Ignore both comments.
Best regards,
Krzysztof
Re: [PATCHv4 4/5] wifi: ath9k: ahb: replace id_table with of
In reply to Rosen PenevQuoted 11 lines · Rosen Penev
Since
2b0996c7646, all of this platform code became no-op with no OF replacement. Not only that, there are no users of AHB here. Add an OF match table that mostly mirrors the original platform device id table. Use a qca prefix as is done for the only other property: qca,no-eeprom. Also used qca prefix for ar9530 as the latter seems to be a mistake.This will be used to add ath9k support for the various ath79 devices here.
Signed-off-by Rosen Penev <[email protected]>---
Best regards,
Krzysztof
PATCH v4 5/5 mips: dts: qca: add wmac support
In reply to Rosen PenevNow that OF ahb support was added to the ath9k driver, we can use it to enable and use the SoC wireless found in these chipsets.
--- arch/mips/boot/dts/qca/ar9132.dtsi | 9 +++++++++ arch/mips/boot/dts/qca/ar9132_tl_wr1043nd_v1.dts | 4 ++++ arch/mips/boot/dts/qca/ar9331.dtsi | 9 +++++++++ arch/mips/boot/dts/qca/ar9331_dpt_module.dts | 4 ++++ arch/mips/boot/dts/qca/ar9331_dragino_ms14.dts | 4 ++++ arch/mips/boot/dts/qca/ar9331_omega.dts | 4 ++++ .../mips/boot/dts/qca/ar9331_openembed_som9331_board.dts | 4 ++++ arch/mips/boot/dts/qca/ar9331_tl_mr3020.dts | 4 ++++ 8 files changed, 42 insertions(+)
arch/mips/boot/dts/qca/ar9132.dtsi +9 -0
@@ -155,6 +155,15 @@ spi: spi@1f000000 { #address-cells = <1>; #size-cells = <0>; }; + + wifi: wifi@180c0000 { + compatible = "qcom,ar9130-wifi"; + reg = <0x180c0000 0x230000>; + + interrupts = <2>; + + status = "disabled"; + }; }; usb_phy: usb-phy {
arch/mips/boot/dts/qca/ar9132_tl_wr1043nd_v1.dts +4 -0
@@ -108,3 +108,7 @@ partition@2 { }; }; }; + +&wifi { + status = "okay"; +};
arch/mips/boot/dts/qca/ar9331.dtsi +9 -0
@@ -285,6 +285,15 @@ spi: spi@1f000000 { status = "disabled"; }; + + wifi: wifi@18100000 { + compatible = "qcom,ar9330-wifi"; + reg = <0x18100000 0x20000>; + + interrupts = <2>; + + status = "disabled"; + }; }; usb_phy: usb-phy {
arch/mips/boot/dts/qca/ar9331_dpt_module.dts +4 -0
@@ -97,3 +97,7 @@ &phy_port0 { &phy_port4 { status = "okay"; }; + +&wifi { + status = "okay"; +};
arch/mips/boot/dts/qca/ar9331_dragino_ms14.dts +4 -0
@@ -98,3 +98,7 @@ spiflash: w25q128@0 { reg = <0>; }; }; + +&wifi { + status = "okay"; +};
arch/mips/boot/dts/qca/ar9331_omega.dts +4 -0
@@ -74,3 +74,7 @@ spiflash: w25q128@0 { reg = <0>; }; }; + +&wifi { + status = "okay"; +};
arch/mips/boot/dts/qca/ar9331_openembed_som9331_board.dts +4 -0
@@ -106,3 +106,7 @@ &phy_port2 { &phy_port4 { status = "okay"; }; + +&wifi { + status = "okay"; +};
arch/mips/boot/dts/qca/ar9331_tl_mr3020.dts +4 -0
@@ -114,3 +114,7 @@ spiflash: s25sl032p@0 { reg = <0>; }; }; + +&wifi { + status = "okay"; +};
Signature · 1 line
2.49.0
Re: [PATCHv4 5/5] mips: dts: qca: add wmac support
Quoted 4 lines · Rosen Penev
Now that OF ahb support was added to the ath9k driver, we can use it to enable and use the SoC wireless found in these chipsets.
Signed-off-by Rosen Penev <[email protected]>
<form letter>
This is an automated instruction, just in case, because many review tags are being ignored. If you know the process, you can skip it (please do not feel offended by me posting it here - no bad intentions intended). If you do not know the process, here is a short explanation:
Please add Acked-by/Reviewed-by/Tested-by tags when posting new versions of patchset, under or above your Signed-off-by tag, unless patch changed significantly (e.g. new properties added to the DT bindings). Tag is "received", when provided in a message replied to you on the mailing list. Tools like b4 can help here. However, there's no need to repost patches *only* to add the tags. The upstream maintainer will do that for tags received on the version they apply.
Full context and explanation:
https://elixir.bootlin.com/linux/v6.12-rc3/source/Documentation/process/submitting-patches.rst#L577
</form letter>
Best regards,
Krzysztof