further mt7988 devicetree work
Subsystems (7)
v4 cover further mt7988 devicetree work
From: Frank Wunderlich <[email protected]>
This series continues mt7988 devicetree work
- Extend cpu frequency scaling with CCI
- GPIO leds
- Basic network-support (ethernet controller + builtin switch + SFP Cages)
depencies (i hope this list is complete and latest patches/series linked):
support interrupt-names because reserved IRQs are now dropped, so index based access is now wrong
https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/
for SFP-Function (macs currently disabled):
PCS clearance which is a 1.5 year discussion currently ongoing
e.g. something like this (one of):
* https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/ (v6)
* https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/ (v4)
* https://patchwork.kernel.org/project/netdevbpf/patch/ba4e359584a6b3bc4b3470822c42186d5b0856f9.1721910728.git.daniel@makrotopia.org/
full usxgmii driver:
https://patchwork.kernel.org/project/netdevbpf/patch/07845ec900ba41ff992875dce12c622277592c32.1702352117.git.daniel@makrotopia.org/
first PCS-discussion is here:
https://patchwork.kernel.org/project/netdevbpf/patch/8aa905080bdb6760875d62cb3b2b41258837f80e.1702352117.git.daniel@makrotopia.org/
and then dts nodes for sgmiisys+usxgmii+2g5 firmware
when above depencies are solved the mac1/2 can be enabled and 2.5G phy/SFP slots will work.
changes:
v4:
net-binding:
- allow interrupt names and increase max interrupts to 6 because of RSS/LRO interrupts (dropped Robs RB due to this change)
dts-patches:
- add interrupts for RSS/LRO and interrupt-names for ethernet node
- eth-reg and clock whitespace-fix
- comment for fixed-link on gmac0
- drop phy-mode properties as suggested by andrew
- drop phy-connection-type on 2g5 board
- reorder some properties
- update 2g5 phy node
- unit-name dec instead of hex to match reg property
- move compatible before reg
- drop phy-mode
v3:
- dropped patches already applied (SPI+thermal)
- added soc specific cci compatible (new binding patch + changed dts)
- enable 2g5 phy because driver is now merged
- add patch for cleaning up unnecessary pins
- add patch for gpio-leds
- add patch for adding ethernet aliases
v2:
- change reg to list of items in eth binding
- changed mt7530 binding:
- unevaluatedProperties=false
- mediatek,pio subproperty
- from patternProperty to property
- board specific properties like led function and labels moved to bpi-r4 dtsi
Frank Wunderlich (13):
dt-bindings: net: mediatek,net: update for mt7988
dt-bindings: net: dsa: mediatek,mt7530: add dsa-port definition for
mt7988
dt-bindings: net: dsa: mediatek,mt7530: add internal mdio bus
dt-bindings: interconnect: add mt7988-cci compatible
arm64: dts: mediatek: mt7988: add cci node
arm64: dts: mediatek: mt7988: add basic ethernet-nodes
arm64: dts: mediatek: mt7988: add switch node
arm64: dts: mediatek: mt7988a-bpi-r4: add proc-supply for cci
arm64: dts: mediatek: mt7988a-bpi-r4: drop unused pins
arm64: dts: mediatek: mt7988a-bpi-r4: add gpio leds
arm64: dts: mediatek: mt7988a-bpi-r4: add aliases for ethernet
arm64: dts: mediatek: mt7988a-bpi-r4: add sfp cages and link to gmac
arm64: dts: mediatek: mt7988a-bpi-r4: configure switch phys and leds
.../bindings/interconnect/mediatek,cci.yaml | 11 +- .../bindings/net/dsa/mediatek,mt7530.yaml | 24 +- .../devicetree/bindings/net/mediatek,net.yaml | 28 +- .../mediatek/mt7988a-bananapi-bpi-r4-2g5.dts | 11 + .../dts/mediatek/mt7988a-bananapi-bpi-r4.dts | 19 ++ .../dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 198 ++++++----- arch/arm64/boot/dts/mediatek/mt7988a.dtsi | 307 +++++++++++++++++- 7 files changed, 498 insertions(+), 100 deletions(-)
Signature · 1 line
2.43.0
PATCH v4 1/13 dt-bindings: net: mediatek,net: update for mt7988
From: Frank Wunderlich <[email protected]>
Update binding for mt7988 which has 3 gmac and 2 reg items.
With RSS-IRQs the interrupt max-items is now 6. Add interrupt-names to make them accessible by name.
---
v4:
- increase max interrupts to 8 because of RSS/LRO interrupts
- dropped Robs RB due to this change
- allow interrupt names
- add interrupt-names without reserved IRQs on mt7988 this requires mtk driver patch:
https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/
v2:
- change reg to list of items
--- .../devicetree/bindings/net/mediatek,net.yaml | 28 ++++++++++++++++--- 1 file changed, 24 insertions(+), 4 deletions(-)
Documentation/devicetree/bindings/net/mediatek,net.yaml +24 -4
@@ -28,7 +28,10 @@ properties: - ralink,rt5350-eth reg: - maxItems: 1 + items: + - description: Register for accessing the MACs. + - description: SoC internal SRAM used for DMA operations. + minItems: 1 clocks: minItems: 2
@@ -40,7 +43,11 @@ properties: interrupts: minItems: 1 - maxItems: 4 + maxItems: 6 + + interrupt-names: + minItems: 1 + maxItems: 6 power-domains: maxItems: 1
@@ -348,7 +355,17 @@ allOf: then: properties: interrupts: - minItems: 4 + minItems: 2 + + interrupt-names: + minItems: 2 + items: + - const: tx + - const: rx + - const: rx-ring0 + - const: rx-ring1 + - const: rx-ring2 + - const: rx-ring3 clocks: minItems: 24
@@ -381,8 +398,11 @@ allOf: - const: xgp2 - const: xgp3 + reg: + minItems: 2 + patternProperties: - "^mac@[0-1]$": + "^mac@[0-2]$": type: object unevaluatedProperties: false allOf:
Signature · 1 line
2.43.0
Aw: [PATCH v4 01/13] dt-bindings: net: mediatek,net: update for mt7988
Hi Rob, Krzysztof and Lorenzo,
I got message from your mailserver, that my patch-mails are detected as Spam and blocked (to other address than i used - seems like forwarding from kernel.org to gmail.com). I want to make sure, you get it...
I see it in dt-bindings patchwork, so replacing the content with a link.
https://patchwork.ozlabs.org/project/devicetree-bindings/patch/[email protected]/
only kept angelo, me and ML in this response to not spam people too much.
regards Frank
Rob Herring
maintainerRe: [PATCH v4 01/13] dt-bindings: net: mediatek,net: update for mt7988
In reply to Frank WunderlichQuoted 11 lines · Frank Wunderlich
From: Frank Wunderlich <[email protected]>
Update binding for mt7988 which has 3 gmac and 2 reg items.
With RSS-IRQs the interrupt max-items is now 6. Add interrupt-names to make them accessible by name.
Signed-off-by Frank Wunderlich <[email protected]>---
v4:
- increase max interrupts to 8 because of RSS/LRO interrupts
But the schema says 6?
Quoted 76 lines
- dropped Robs RB due to this change
- allow interrupt names
- add interrupt-names without reserved IRQs on mt7988 this requires mtk driver patch:
https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/v2:
- change reg to list of items--- .../devicetree/bindings/net/mediatek,net.yaml | 28 ++++++++++++++++--- 1 file changed, 24 insertions(+), 4 deletions(-)Documentation/devicetree/bindings/net/mediatek,net.yaml +24
-4@@ -28,7 +28,10 @@ properties: - ralink,rt5350-eth reg: - maxItems: 1 + items: + - description: Register for accessing the MACs. + - description: SoC internal SRAM used for DMA operations. + minItems: 1 clocks: minItems: 2@@ -40,7 +43,11 @@ properties: interrupts: minItems: 1 - maxItems: 4 + maxItems: 6 + + interrupt-names: + minItems: 1 + maxItems: 6 power-domains: maxItems: 1@@ -348,7 +355,17 @@ allOf: then: properties: interrupts: - minItems: 4 + minItems: 2 + + interrupt-names: + minItems: 2 + items: + - const: tx + - const: rx + - const: rx-ring0 + - const: rx-ring1 + - const: rx-ring2 + - const: rx-ring3 clocks: minItems: 24@@ -381,8 +398,11 @@ allOf: - const: xgp2 - const: xgp3 + reg: + minItems: 2 + patternProperties: - "^mac@[0-1]$": + "^mac@[0-2]$": type: object unevaluatedProperties: false allOf:Signature · 1 line
2.43.0
Re: [PATCH v4 01/13] dt-bindings: net: mediatek,net: update for mt7988
Am 17. Juni 2025 17:13:54 MESZ schrieb Rob Herring <[email protected]>:
Quoted 8 lines · Frank Wunderlich
Quoted 7 lines
From: Frank Wunderlich <[email protected]>
Update binding for mt7988 which has 3 gmac and 2 reg items.
With RSS-IRQs the interrupt max-items is now 6. Add interrupt-names to make them accessible by name.
Quoted 6 lines
Quoted 4 lines
Signed-off-by Frank Wunderlich <[email protected]>---
v4:
- increase max interrupts to 8 because of RSS/LRO interruptsBut the schema says 6?
Yes it was an error in changelog,see mail i
sent later to you and ML. 8 was previously
because original version had 2 reserved irqs
around rx+tx i dropped later by using
irq-names.
See my patch introducing irq-names in mtk
eth driver:
<https://patchwork.kernel.org/project/linux-mediatek/patch/[email protected]/>
Original (downstream/sdk) was (but
index-based):
rsv
rx
tx
rsv/misc
rx-ring0
...
rx-ring3
So total 8 and i don't wanted to add 2
reserved irq to dts forever so i decided
moving to irq-names now.
Quoted 64 lines
Quoted 64 lines
- dropped Robs RB due to this change
- allow interrupt names
- add interrupt-names without reserved IRQs on mt7988 this requires mtk driver patch:
https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/v2:
- change reg to list of items--- .../devicetree/bindings/net/mediatek,net.yaml | 28 ++++++++++++++++--- 1 file changed, 24 insertions(+), 4 deletions(-)Documentation/devicetree/bindings/net/mediatek,net.yaml +20
-3@@ -28,7 +28,10 @@ properties: - ralink,rt5350-eth reg: - maxItems: 1 + items: + - description: Register for accessing the MACs. + - description: SoC internal SRAM used for DMA operations. + minItems: 1 clocks: minItems: 2@@ -40,7 +43,11 @@ properties: interrupts: minItems: 1 - maxItems: 4 + maxItems: 6 + + interrupt-names: + minItems: 1 + maxItems: 6 power-domains: maxItems: 1@@ -348,7 +355,17 @@ allOf: then: properties: interrupts: - minItems: 4 + minItems: 2 + + interrupt-names: + minItems: 2 + items: + - const: tx + - const: rx + - const: rx-ring0 + - const: rx-ring1 + - const: rx-ring2 + - const: rx-ring3 clocks: minItems: 24@@ -381,8 +398,11 @@ allOf: - const: xgp2 - const: xgp3
Quoted 12 lines
Quoted 12 lines
Documentation/devicetree/bindings/net/mediatek,net.yaml +4
-1+ reg: + minItems: 2 + patternProperties: - "^mac@[0-1]$": + "^mac@[0-2]$": type: object unevaluatedProperties: false allOf:Signature · 1 line
2.43.0
regards Frank
Re: [PATCH v4 01/13] dt-bindings: net: mediatek,net: update for mt7988
In reply to Frank WunderlichQuoted 17 lines · Frank Wunderlich
From: Frank Wunderlich <[email protected]>
Update binding for mt7988 which has 3 gmac and 2 reg items.
With RSS-IRQs the interrupt max-items is now 6. Add interrupt-names to make them accessible by name.
Signed-off-by Frank Wunderlich <[email protected]>---
v4:
- increase max interrupts to 8 because of RSS/LRO interrupts
- dropped Robs RB due to this change
- allow interrupt names
- add interrupt-names without reserved IRQs on mt7988 this requires mtk driver patch:
https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/
Quoted 6 lines
v2:
- change reg to list of items--- .../devicetree/bindings/net/mediatek,net.yaml | 28 ++++++++++++++++--- 1 file changed, 24 insertions(+), 4 deletions(-)
Re: [PATCH v4 01/13] dt-bindings: net: mediatek,net: update for mt7988
Am 18. Juni 2025 19:38:07 MESZ schrieb "Rob Herring (Arm)" <[email protected]>:
Quoted 19 lines · Frank Wunderlich
Quoted 17 lines
From: Frank Wunderlich <[email protected]>
Update binding for mt7988 which has 3 gmac and 2 reg items.
With RSS-IRQs the interrupt max-items is now 6. Add interrupt-names to make them accessible by name.
Signed-off-by Frank Wunderlich <[email protected]>---
v4:
- increase max interrupts to 8 because of RSS/LRO interrupts
- dropped Robs RB due to this change
- allow interrupt names
- add interrupt-names without reserved IRQs on mt7988 this requires mtk driver patch:
https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/
Quoted 8 lines
Quoted 6 lines
v2:
- change reg to list of items--- .../devicetree/bindings/net/mediatek,net.yaml | 28 ++++++++++++++++--- 1 file changed, 24 insertions(+), 4 deletions(-)Reviewed-by Rob Herring (Arm) <[email protected]>
Thank you rob.
Have you seen my reponse to coverletter? Got info from mtk that reserved irqs are not unusable (only currently unused) and imho they should be upstreamed too but without a special meaning.
What do you think?
I would increase the interupts count to 8 and name the reserved irqs fe0..fe3. can i keep your RB or should i drop it again?
regards Frank
PATCH v4 2/13 dt-bindings: net: dsa: mediatek,mt7530: add dsa-port definition for mt7988
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add own dsa-port binding for SoC with internal switch where only phy-mode 'internal' is valid.
--- .../bindings/net/dsa/mediatek,mt7530.yaml | 14 +++++++++++++- 1 file changed, 13 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml +13 -1
@@ -190,6 +190,18 @@ required: - reg $defs: + builtin-dsa-port: + patternProperties: + "^(ethernet-)?ports$": + patternProperties: + "^(ethernet-)?port@[0-6]$": + if: + required: [ ethernet ] + then: + properties: + phy-mode: + const: internal + mt7530-dsa-port: patternProperties: "^(ethernet-)?ports$":
@@ -297,7 +309,7 @@ allOf: - airoha,en7581-switch - airoha,an7583-switch then: - $ref: "#/$defs/mt7530-dsa-port" + $ref: "#/$defs/builtin-dsa-port" properties: gpio-controller: false mediatek,mcm: false
Signature · 1 line
2.43.0
PATCH v4 3/13 dt-bindings: net: dsa: mediatek,mt7530: add internal mdio bus
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Mt7988 buildin switch has own mdio bus where ge-phys are connected. Add related property for this.
---
v2:
- change from patternproperty to property
- add unevaluatedProperties and mediatek,pio subproperty
--- .../devicetree/bindings/net/dsa/mediatek,mt7530.yaml | 10 ++++++++++ 1 file changed, 10 insertions(+)
Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml +10 -0
@@ -136,6 +136,16 @@ properties: See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt for details for the regulator setup on these boards. + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + + properties: + mediatek,pio: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle pointing to the mediatek pinctrl node. + mediatek,mcm: type: boolean description:
Signature · 1 line
2.43.0
PATCH v4 4/13 dt-bindings: interconnect: add mt7988-cci compatible
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add compatible for Mediatek MT7988 SoC with mediatek,mt8183-cci fallback which is taken by driver.
---
v2:
- no RFC
- drop "items" as sugested by conor
--- .../bindings/interconnect/mediatek,cci.yaml | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-)
Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml +8 -3
@@ -17,9 +17,14 @@ description: | properties: compatible: - enum: - - mediatek,mt8183-cci - - mediatek,mt8186-cci + oneOf: + - enum: + - mediatek,mt8183-cci + - mediatek,mt8186-cci + - items: + - enum: + - mediatek,mt7988-cci + - const: mediatek,mt8183-cci clocks: items:
Signature · 1 line
2.43.0
PATCH v4 5/13 arm64: dts: mediatek: mt7988: add cci node
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add cci devicetree node for cpu frequency scaling.
---
v3:
- add mt7988-cci compatible as suggested by angelo
--- arch/arm64/boot/dts/mediatek/mt7988a.dtsi | 33 +++++++++++++++++++++++ 1 file changed, 33 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a.dtsi +33 -0
@@ -12,6 +12,35 @@ / { #address-cells = <2>; #size-cells = <2>; + cci: cci { + compatible = "mediatek,mt7988-cci", "mediatek,mt8183-cci"; + clocks = <&mcusys CLK_MCU_BUS_DIV_SEL>, + <&topckgen CLK_TOP_XTAL>; + clock-names = "cci", "intermediate"; + operating-points-v2 = <&cci_opp>; + }; + + cci_opp: opp-table-cci { + compatible = "operating-points-v2"; + opp-shared; + opp-480000000 { + opp-hz = /bits/ 64 <480000000>; + opp-microvolt = <850000>; + }; + opp-660000000 { + opp-hz = /bits/ 64 <660000000>; + opp-microvolt = <850000>; + }; + opp-900000000 { + opp-hz = /bits/ 64 <900000000>; + opp-microvolt = <850000>; + }; + opp-1080000000 { + opp-hz = /bits/ 64 <1080000000>; + opp-microvolt = <900000>; + }; + }; + cpus { #address-cells = <1>; #size-cells = <0>;
@@ -25,6 +54,7 @@ cpu0: cpu@0 { <&topckgen CLK_TOP_XTAL>; clock-names = "cpu", "intermediate"; operating-points-v2 = <&cluster0_opp>; + mediatek,cci = <&cci>; }; cpu1: cpu@1 {
@@ -36,6 +66,7 @@ cpu1: cpu@1 { <&topckgen CLK_TOP_XTAL>; clock-names = "cpu", "intermediate"; operating-points-v2 = <&cluster0_opp>; + mediatek,cci = <&cci>; }; cpu2: cpu@2 {
@@ -47,6 +78,7 @@ cpu2: cpu@2 { <&topckgen CLK_TOP_XTAL>; clock-names = "cpu", "intermediate"; operating-points-v2 = <&cluster0_opp>; + mediatek,cci = <&cci>; }; cpu3: cpu@3 {
@@ -58,6 +90,7 @@ cpu3: cpu@3 { <&topckgen CLK_TOP_XTAL>; clock-names = "cpu", "intermediate"; operating-points-v2 = <&cluster0_opp>; + mediatek,cci = <&cci>; }; cluster0_opp: opp-table-0 {
Signature · 1 line
2.43.0
PATCH v4 6/13 arm64: dts: mediatek: mt7988: add basic ethernet-nodes
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add basic ethernet related nodes.
Mac1+2 needs pcs (sgmii+usxgmii) to work correctly which will be linked later when driver is merged.
---
v4:
- comment for fixed-link on gmac0
- update 2g5 phy node
- unit-name dec instead of hex to match reg property
- move compatible before reg
- drop phy-mode
- add interrupts for RSS
- add interrupt-names and drop reserved irqs for ethernet
- some reordering
- eth-reg and clock whitespace-fix based on angelos review
--- arch/arm64/boot/dts/mediatek/mt7988a.dtsi | 126 +++++++++++++++++++++- 1 file changed, 123 insertions(+), 3 deletions(-)
arch/arm64/boot/dts/mediatek/mt7988a.dtsi +123 -3
@@ -680,7 +680,28 @@ xphyu3port0: usb-phy@11e13000 { }; }; - clock-controller@11f40000 { + xfi_tphy0: phy@11f20000 { + compatible = "mediatek,mt7988-xfi-tphy"; + reg = <0 0x11f20000 0 0x10000>; + clocks = <&xfi_pll CLK_XFIPLL_PLL_EN>, + <&topckgen CLK_TOP_XFI_PHY_0_XTAL_SEL>; + clock-names = "xfipll", "topxtal"; + resets = <&watchdog 14>; + mediatek,usxgmii-performance-errata; + #phy-cells = <0>; + }; + + xfi_tphy1: phy@11f30000 { + compatible = "mediatek,mt7988-xfi-tphy"; + reg = <0 0x11f30000 0 0x10000>; + clocks = <&xfi_pll CLK_XFIPLL_PLL_EN>, + <&topckgen CLK_TOP_XFI_PHY_1_XTAL_SEL>; + clock-names = "xfipll", "topxtal"; + resets = <&watchdog 15>; + #phy-cells = <0>; + }; + + xfi_pll: clock-controller@11f40000 { compatible = "mediatek,mt7988-xfi-pll"; reg = <0 0x11f40000 0 0x1000>; resets = <&watchdog 16>;
@@ -714,19 +735,118 @@ phy_calibration_p3: calib@97c { }; }; - clock-controller@15000000 { + ethsys: clock-controller@15000000 { compatible = "mediatek,mt7988-ethsys", "syscon"; reg = <0 0x15000000 0 0x1000>; #clock-cells = <1>; #reset-cells = <1>; }; - clock-controller@15031000 { + ethwarp: clock-controller@15031000 { compatible = "mediatek,mt7988-ethwarp"; reg = <0 0x15031000 0 0x1000>; #clock-cells = <1>; #reset-cells = <1>; }; + + eth: ethernet@15100000 { + compatible = "mediatek,mt7988-eth"; + reg = <0 0x15100000 0 0x80000>, <0 0x15400000 0 0x200000>; + interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "tx", "rx", "rx-ring0", "rx-ring1", + "rx-ring2", "rx-ring3"; + clocks = <ðsys CLK_ETHDMA_CRYPT0_EN>, + <ðsys CLK_ETHDMA_FE_EN>, + <ðsys CLK_ETHDMA_GP2_EN>, + <ðsys CLK_ETHDMA_GP1_EN>, + <ðsys CLK_ETHDMA_GP3_EN>, + <ðwarp CLK_ETHWARP_WOCPU2_EN>, + <ðwarp CLK_ETHWARP_WOCPU1_EN>, + <ðwarp CLK_ETHWARP_WOCPU0_EN>, + <ðsys CLK_ETHDMA_ESW_EN>, + <&topckgen CLK_TOP_ETH_GMII_SEL>, + <&topckgen CLK_TOP_ETH_REFCK_50M_SEL>, + <&topckgen CLK_TOP_ETH_SYS_200M_SEL>, + <&topckgen CLK_TOP_ETH_SYS_SEL>, + <&topckgen CLK_TOP_ETH_XGMII_SEL>, + <&topckgen CLK_TOP_ETH_MII_SEL>, + <&topckgen CLK_TOP_NETSYS_SEL>, + <&topckgen CLK_TOP_NETSYS_500M_SEL>, + <&topckgen CLK_TOP_NETSYS_PAO_2X_SEL>, + <&topckgen CLK_TOP_NETSYS_SYNC_250M_SEL>, + <&topckgen CLK_TOP_NETSYS_PPEFB_250M_SEL>, + <&topckgen CLK_TOP_NETSYS_WARP_SEL>, + <ðsys CLK_ETHDMA_XGP1_EN>, + <ðsys CLK_ETHDMA_XGP2_EN>, + <ðsys CLK_ETHDMA_XGP3_EN>; + clock-names = "crypto", "fe", "gp2", "gp1", "gp3", + "ethwarp_wocpu2", "ethwarp_wocpu1", + "ethwarp_wocpu0", "esw", "top_eth_gmii_sel", + "top_eth_refck_50m_sel", "top_eth_sys_200m_sel", + "top_eth_sys_sel", "top_eth_xgmii_sel", + "top_eth_mii_sel", "top_netsys_sel", + "top_netsys_500m_sel", "top_netsys_pao_2x_sel", + "top_netsys_sync_250m_sel", + "top_netsys_ppefb_250m_sel", + "top_netsys_warp_sel","xgp1", "xgp2", "xgp3"; + assigned-clocks = <&topckgen CLK_TOP_NETSYS_2X_SEL>, + <&topckgen CLK_TOP_NETSYS_GSW_SEL>, + <&topckgen CLK_TOP_USXGMII_SBUS_0_SEL>, + <&topckgen CLK_TOP_USXGMII_SBUS_1_SEL>, + <&topckgen CLK_TOP_SGM_0_SEL>, + <&topckgen CLK_TOP_SGM_1_SEL>; + assigned-clock-parents = <&apmixedsys CLK_APMIXED_NET2PLL>, + <&topckgen CLK_TOP_NET1PLL_D4>, + <&topckgen CLK_TOP_NET1PLL_D8_D4>, + <&topckgen CLK_TOP_NET1PLL_D8_D4>, + <&apmixedsys CLK_APMIXED_SGMPLL>, + <&apmixedsys CLK_APMIXED_SGMPLL>; + #address-cells = <1>; + #size-cells = <0>; + mediatek,ethsys = <ðsys>; + mediatek,infracfg = <&topmisc>; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "internal"; + + /* Connected to internal switch */ + fixed-link { + speed = <10000>; + full-duplex; + pause; + }; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + status = "disabled"; + }; + + gmac2: mac@2 { + compatible = "mediatek,eth-mac"; + reg = <2>; + status = "disabled"; + }; + + mdio_bus: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + + /* internal 2.5G PHY */ + int_2p5g_phy: ethernet-phy@15 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <15>; + }; + }; + }; }; thermal-zones {
Signature · 1 line
2.43.0
PATCH v4 7/13 arm64: dts: mediatek: mt7988: add switch node
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add mt7988 builtin mt753x switch nodes.
---
v4:
- drop phy-mode for gsw-phy
- reorder phy-mode after phy-handle
- drop interrupt parent from switch
v2:
- drop labels and led-function too (have to be in board)
--- arch/arm64/boot/dts/mediatek/mt7988a.dtsi | 148 ++++++++++++++++++++++ 1 file changed, 148 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a.dtsi +148 -0
@@ -742,6 +742,154 @@ ethsys: clock-controller@15000000 { #reset-cells = <1>; }; + switch: switch@15020000 { + compatible = "mediatek,mt7988-switch"; + reg = <0 0x15020000 0 0x8000>; + interrupt-controller; + #interrupt-cells = <1>; + interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; + resets = <ðwarp MT7988_ETHWARP_RST_SWITCH>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + gsw_port0: port@0 { + reg = <0>; + phy-handle = <&gsw_phy0>; + phy-mode = "internal"; + }; + + gsw_port1: port@1 { + reg = <1>; + phy-handle = <&gsw_phy1>; + phy-mode = "internal"; + }; + + gsw_port2: port@2 { + reg = <2>; + phy-handle = <&gsw_phy2>; + phy-mode = "internal"; + }; + + gsw_port3: port@3 { + reg = <3>; + phy-handle = <&gsw_phy3>; + phy-mode = "internal"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "internal"; + + fixed-link { + speed = <10000>; + full-duplex; + pause; + }; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + mediatek,pio = <&pio>; + + gsw_phy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + interrupts = <0>; + nvmem-cells = <&phy_calibration_p0>; + nvmem-cell-names = "phy-cal-data"; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + gsw_phy0_led0: led@0 { + reg = <0>; + status = "disabled"; + }; + + gsw_phy0_led1: led@1 { + reg = <1>; + status = "disabled"; + }; + }; + }; + + gsw_phy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + interrupts = <1>; + nvmem-cells = <&phy_calibration_p1>; + nvmem-cell-names = "phy-cal-data"; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + gsw_phy1_led0: led@0 { + reg = <0>; + status = "disabled"; + }; + + gsw_phy1_led1: led@1 { + reg = <1>; + status = "disabled"; + }; + }; + }; + + gsw_phy2: ethernet-phy@2 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <2>; + interrupts = <2>; + nvmem-cells = <&phy_calibration_p2>; + nvmem-cell-names = "phy-cal-data"; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + gsw_phy2_led0: led@0 { + reg = <0>; + status = "disabled"; + }; + + gsw_phy2_led1: led@1 { + reg = <1>; + status = "disabled"; + }; + }; + }; + + gsw_phy3: ethernet-phy@3 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <3>; + interrupts = <3>; + nvmem-cells = <&phy_calibration_p3>; + nvmem-cell-names = "phy-cal-data"; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + gsw_phy3_led0: led@0 { + reg = <0>; + status = "disabled"; + }; + + gsw_phy3_led1: led@1 { + reg = <1>; + status = "disabled"; + }; + }; + }; + }; + }; + ethwarp: clock-controller@15031000 { compatible = "mediatek,mt7988-ethwarp"; reg = <0 0x15031000 0 0x1000>;
Signature · 1 line
2.43.0
PATCH v4 8/13 arm64: dts: mediatek: mt7988a-bpi-r4: add proc-supply for cci
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
CCI requires proc-supply. Add it on board level.
--- arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 4 ++++ 1 file changed, 4 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi +4 -0
@@ -40,6 +40,10 @@ reg_3p3v: regulator-3p3v { }; }; +&cci { + proc-supply = <&rt5190_buck3>; +}; + &cpu0 { proc-supply = <&rt5190_buck3>; };
Signature · 1 line
2.43.0
PATCH v4 9/13 arm64: dts: mediatek: mt7988a-bpi-r4: drop unused pins
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Pins were moved from SoC dtsi to Board level dtsi without cleaning up to needed ones. Drop the unused pins now.
--- .../dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 89 ------------------- 1 file changed, 89 deletions(-)
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi +0 -89
@@ -223,18 +223,6 @@ &pcie3 { }; &pio { - mdio0_pins: mdio0-pins { - mux { - function = "eth"; - groups = "mdc_mdio0"; - }; - - conf { - pins = "SMI_0_MDC", "SMI_0_MDIO"; - drive-strength = <8>; - }; - }; - i2c0_pins: i2c0-g0-pins { mux { function = "i2c";
@@ -249,20 +237,6 @@ mux { }; }; - i2c1_sfp_pins: i2c1-sfp-g0-pins { - mux { - function = "i2c"; - groups = "i2c1_sfp"; - }; - }; - - i2c2_0_pins: i2c2-g0-pins { - mux { - function = "i2c"; - groups = "i2c2_0"; - }; - }; - i2c2_1_pins: i2c2-g1-pins { mux { function = "i2c";
@@ -298,34 +272,6 @@ mux { }; }; - gbe0_led1_pins: gbe0-led1-pins { - mux { - function = "led"; - groups = "gbe0_led1"; - }; - }; - - gbe1_led1_pins: gbe1-led1-pins { - mux { - function = "led"; - groups = "gbe1_led1"; - }; - }; - - gbe2_led1_pins: gbe2-led1-pins { - mux { - function = "led"; - groups = "gbe2_led1"; - }; - }; - - gbe3_led1_pins: gbe3-led1-pins { - mux { - function = "led"; - groups = "gbe3_led1"; - }; - }; - i2p5gbe_led0_pins: 2p5gbe-led0-pins { mux { function = "led";
@@ -333,13 +279,6 @@ mux { }; }; - i2p5gbe_led1_pins: 2p5gbe-led1-pins { - mux { - function = "led"; - groups = "2p5gbe_led1"; - }; - }; - mmc0_pins_emmc_45: mmc0-emmc-45-pins { mux { function = "flash";
@@ -361,40 +300,12 @@ mux { }; }; - snfi_pins: snfi-pins { - mux { - function = "flash"; - groups = "snfi"; - }; - }; - - spi0_pins: spi0-pins { - mux { - function = "spi"; - groups = "spi0"; - }; - }; - spi0_flash_pins: spi0-flash-pins { mux { function = "spi"; groups = "spi0", "spi0_wp_hold"; }; }; - - spi2_pins: spi2-pins { - mux { - function = "spi"; - groups = "spi2"; - }; - }; - - spi2_flash_pins: spi2-flash-pins { - mux { - function = "spi"; - groups = "spi2", "spi2_wp_hold"; - }; - }; }; &pwm {
Signature · 1 line
2.43.0
PATCH v4 10/13 arm64: dts: mediatek: mt7988a-bpi-r4: add gpio leds
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Bananapi R4 has a green and a blue led which can be switched by gpio. Green led is for running state so default on.
Green led also shares pin with eeprom writeprotect where led off allows writing to eeprom.
--- .../dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi +19 -0
@@ -21,6 +21,25 @@ fan: pwm-fan { status = "okay"; }; + gpio-leds { + compatible = "gpio-leds"; + + led_green: led-green { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_GREEN>; + gpios = <&pio 79 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + led_blue: led-blue { + function = LED_FUNCTION_WPS; + color = <LED_COLOR_ID_BLUE>; + gpios = <&pio 63 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + reg_1p8v: regulator-1p8v { compatible = "regulator-fixed"; regulator-name = "fixed-1.8V";
Signature · 1 line
2.43.0
PATCH v4 11/13 arm64: dts: mediatek: mt7988a-bpi-r4: add aliases for ethernet
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add aliases for gmacs to allow bootloader setting mac-adresses.
--- arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 6 ++++++ 1 file changed, 6 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi +6 -0
@@ -8,6 +8,12 @@ #include "mt7988a.dtsi" / { + aliases { + ethernet0 = &gmac0; + ethernet1 = &gmac1; + ethernet2 = &gmac2; + }; + chosen { stdout-path = "serial0:115200n8"; };
Signature · 1 line
2.43.0
PATCH v4 12/13 arm64: dts: mediatek: mt7988a-bpi-r4: add sfp cages and link to gmac
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add SFP cages to Bananapi-R4 board. The 2.5g phy variant only contains the wan-SFP, so add this to common dtsi and the lan-sfp only to the dual-SFP variant.
---
v4:
- update 2g5-board (reorder and drop phy-connection-type)
- order sfp properties
v3:
- enable mac with 2.5g phy on r4 phy variant because driver is now mainline
--- .../mediatek/mt7988a-bananapi-bpi-r4-2g5.dts | 11 +++++++++++ .../dts/mediatek/mt7988a-bananapi-bpi-r4.dts | 19 +++++++++++++++++++ .../dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 19 +++++++++++++++++++ 3 files changed, 49 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4-2g5.dts +11 -0
@@ -9,3 +9,14 @@ / { model = "Banana Pi BPI-R4 (1x SFP+, 1x 2.5GbE)"; chassis-type = "embedded"; }; + +&gmac1 { + phy = <&int_2p5g_phy>; + phy-mode = "internal"; + status = "okay"; +}; + +&int_2p5g_phy { + pinctrl-0 = <&i2p5gbe_led0_pins>; + pinctrl-names = "i2p5gbe-led"; +};
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dts +19 -0
@@ -8,6 +8,25 @@ / { compatible = "bananapi,bpi-r4", "mediatek,mt7988a"; model = "Banana Pi BPI-R4 (2x SFP+)"; chassis-type = "embedded"; + + /* SFP2 cage (LAN) */ + sfp2: sfp2 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp2>; + maximum-power-milliwatt = <3000>; + + los-gpios = <&pio 2 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&pio 83 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&pio 3 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&pio 0 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&pio 1 GPIO_ACTIVE_HIGH>; + }; +}; + +&gmac1 { + managed = "in-band-status"; + phy-mode = "usxgmii"; + sfp = <&sfp2>; }; &pca9545 {
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi +19 -0
@@ -63,6 +63,19 @@ reg_3p3v: regulator-3p3v { regulator-boot-on; regulator-always-on; }; + + /* SFP1 cage (WAN) */ + sfp1: sfp1 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp1>; + maximum-power-milliwatt = <3000>; + + los-gpios = <&pio 54 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&pio 82 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&pio 21 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&pio 70 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&pio 69 GPIO_ACTIVE_HIGH>; + }; }; &cci {
@@ -133,6 +146,12 @@ map-cpu-active-low { }; }; +&gmac2 { + managed = "in-band-status"; + phy-mode = "usxgmii"; + sfp = <&sfp1>; +}; + &i2c0 { pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins>;
Signature · 1 line
2.43.0
PATCH v4 13/13 arm64: dts: mediatek: mt7988a-bpi-r4: configure switch phys and leds
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Assign pinctrl to switch phys and leds.
---
v4:
- reorder switch phy(-led) properties
v2:
- add labels and led-function and include after dropping from soc dtsi
--- .../dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 61 +++++++++++++++++++ 1 file changed, 61 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi +61 -0
@@ -4,6 +4,7 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/regulator/richtek,rt5190a-regulator.h> +#include <dt-bindings/leds/common.h> #include "mt7988a.dtsi"
@@ -152,6 +153,66 @@ &gmac2 { sfp = <&sfp1>; }; +&gsw_phy0 { + pinctrl-0 = <&gbe0_led0_pins>; + pinctrl-names = "gbe-led"; +}; + +&gsw_phy0_led0 { + function = LED_FUNCTION_WAN; + color = <LED_COLOR_ID_GREEN>; + status = "okay"; +}; + +&gsw_port0 { + label = "wan"; +}; + +&gsw_phy1 { + pinctrl-0 = <&gbe1_led0_pins>; + pinctrl-names = "gbe-led"; +}; + +&gsw_phy1_led0 { + function = LED_FUNCTION_LAN; + color = <LED_COLOR_ID_GREEN>; + status = "okay"; +}; + +&gsw_port1 { + label = "lan1"; +}; + +&gsw_phy2 { + pinctrl-0 = <&gbe2_led0_pins>; + pinctrl-names = "gbe-led"; +}; + +&gsw_phy2_led0 { + function = LED_FUNCTION_LAN; + color = <LED_COLOR_ID_GREEN>; + status = "okay"; +}; + +&gsw_port2 { + label = "lan2"; +}; + +&gsw_phy3 { + pinctrl-0 = <&gbe3_led0_pins>; + pinctrl-names = "gbe-led"; +}; + +&gsw_phy3_led0 { + function = LED_FUNCTION_LAN; + color = <LED_COLOR_ID_GREEN>; + status = "okay"; +}; + +&gsw_port3 { + label = "lan3"; +}; + &i2c0 { pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins>;
Signature · 1 line
2.43.0
AngeloGioacchino Del Regno
maintainerIl 16/06/25 11:58, Frank Wunderlich ha scritto:
Quoted 2 lines
From: Frank Wunderlich <[email protected]>
I think that this series is ready to be applied; however, I need someone to take the bindings before I can apply the devicetree part to the MediaTek trees.
Cheers,
Angelo
Quoted 90 lines
This series continues mt7988 devicetree work
- Extend cpu frequency scaling with CCI
- GPIO leds
- Basic network-support (ethernet controller + builtin switch + SFP Cages)depencies (i hope this list is complete and latest patches/series linked):
support interrupt-names because reserved IRQs are now dropped, so index based access is now wrong
https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/for SFP-Function (macs currently disabled):
PCS clearance which is a 1.5 year discussion currently ongoing
e.g. something like this (one of):
* https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/ (v6)
* https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/ (v4)
* https://patchwork.kernel.org/project/netdevbpf/patch/ba4e359584a6b3bc4b3470822c42186d5b0856f9.1721910728.git.daniel@makrotopia.org/full usxgmii driver:
https://patchwork.kernel.org/project/netdevbpf/patch/07845ec900ba41ff992875dce12c622277592c32.1702352117.git.daniel@makrotopia.org/first PCS-discussion is here:
https://patchwork.kernel.org/project/netdevbpf/patch/8aa905080bdb6760875d62cb3b2b41258837f80e.1702352117.git.daniel@makrotopia.org/and then dts nodes for sgmiisys+usxgmii+2g5 firmware
when above depencies are solved the mac1/2 can be enabled and 2.5G phy/SFP slots will work.
changes:
v4:
net-binding:
- allow interrupt names and increase max interrupts to 6 because of RSS/LRO interrupts (dropped Robs RB due to this change)dts-patches:
- add interrupts for RSS/LRO and interrupt-names for ethernet node
- eth-reg and clock whitespace-fix
- comment for fixed-link on gmac0
- drop phy-mode properties as suggested by andrew
- drop phy-connection-type on 2g5 board
- reorder some properties
- update 2g5 phy node
- unit-name dec instead of hex to match reg property
- move compatible before reg
- drop phy-modev3:
- dropped patches already applied (SPI+thermal)
- added soc specific cci compatible (new binding patch + changed dts)
- enable 2g5 phy because driver is now merged
- add patch for cleaning up unnecessary pins
- add patch for gpio-leds
- add patch for adding ethernet aliasesv2:
- change reg to list of items in eth binding
- changed mt7530 binding:
- unevaluatedProperties=false
- mediatek,pio subproperty
- from patternProperty to property
- board specific properties like led function and labels moved to bpi-r4 dtsiFrank Wunderlich (13):
dt-bindings: net: mediatek,net: update for mt7988
dt-bindings: net: dsa: mediatek,mt7530: add dsa-port definition formt7988dt-bindings: net: dsa: mediatek,mt7530: add internal mdio bus
dt-bindings: interconnect: add mt7988-cci compatible
arm64: dts: mediatek: mt7988: add cci node
arm64: dts: mediatek: mt7988: add basic ethernet-nodes
arm64: dts: mediatek: mt7988: add switch node
arm64: dts: mediatek: mt7988a-bpi-r4: add proc-supply for cci
arm64: dts: mediatek: mt7988a-bpi-r4: drop unused pins
arm64: dts: mediatek: mt7988a-bpi-r4: add gpio leds
arm64: dts: mediatek: mt7988a-bpi-r4: add aliases for ethernet
arm64: dts: mediatek: mt7988a-bpi-r4: add sfp cages and link to gmac
arm64: dts: mediatek: mt7988a-bpi-r4: configure switch phys and leds.../bindings/interconnect/mediatek,cci.yaml | 11 +- .../bindings/net/dsa/mediatek,mt7530.yaml | 24 +- .../devicetree/bindings/net/mediatek,net.yaml | 28 +- .../mediatek/mt7988a-bananapi-bpi-r4-2g5.dts | 11 + .../dts/mediatek/mt7988a-bananapi-bpi-r4.dts | 19 ++ .../dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 198 ++++++----- arch/arm64/boot/dts/mediatek/mt7988a.dtsi | 307 +++++++++++++++++- 7 files changed, 498 insertions(+), 100 deletions(-)
Am 19. Juni 2025 07:57:09 MESZ schrieb AngeloGioacchino Del Regno <[email protected]>:
Quoted 6 lines
Il 16/06/25 11:58, Frank Wunderlich ha scritto:
Quoted 2 lines
From: Frank Wunderlich <[email protected]>
I think that this series is ready to be applied; however, I need someone to take the bindings before I can apply the devicetree part to the MediaTek trees.
Please wait a bit for the eth part...seems like reserved irqs are not unusable as i thought...i think we should upstream them too and maybe with different names...as they are not fixed to function in hardware.
Quoted 96 lines
Cheers,
AngeloQuoted 90 lines
This series continues mt7988 devicetree work
- Extend cpu frequency scaling with CCI
- GPIO leds
- Basic network-support (ethernet controller + builtin switch + SFP Cages)depencies (i hope this list is complete and latest patches/series linked):
support interrupt-names because reserved IRQs are now dropped, so index based access is now wrong
https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/for SFP-Function (macs currently disabled):
PCS clearance which is a 1.5 year discussion currently ongoing
e.g. something like this (one of):
* https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/ (v6)
* https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/ (v4)
* https://patchwork.kernel.org/project/netdevbpf/patch/ba4e359584a6b3bc4b3470822c42186d5b0856f9.1721910728.git.daniel@makrotopia.org/full usxgmii driver:
https://patchwork.kernel.org/project/netdevbpf/patch/07845ec900ba41ff992875dce12c622277592c32.1702352117.git.daniel@makrotopia.org/first PCS-discussion is here:
https://patchwork.kernel.org/project/netdevbpf/patch/8aa905080bdb6760875d62cb3b2b41258837f80e.1702352117.git.daniel@makrotopia.org/and then dts nodes for sgmiisys+usxgmii+2g5 firmware
when above depencies are solved the mac1/2 can be enabled and 2.5G phy/SFP slots will work.
changes:
v4:
net-binding:
- allow interrupt names and increase max interrupts to 6 because of RSS/LRO interrupts (dropped Robs RB due to this change)dts-patches:
- add interrupts for RSS/LRO and interrupt-names for ethernet node
- eth-reg and clock whitespace-fix
- comment for fixed-link on gmac0
- drop phy-mode properties as suggested by andrew
- drop phy-connection-type on 2g5 board
- reorder some properties
- update 2g5 phy node
- unit-name dec instead of hex to match reg property
- move compatible before reg
- drop phy-modev3:
- dropped patches already applied (SPI+thermal)
- added soc specific cci compatible (new binding patch + changed dts)
- enable 2g5 phy because driver is now merged
- add patch for cleaning up unnecessary pins
- add patch for gpio-leds
- add patch for adding ethernet aliasesv2:
- change reg to list of items in eth binding
- changed mt7530 binding:
- unevaluatedProperties=false
- mediatek,pio subproperty
- from patternProperty to property
- board specific properties like led function and labels moved to bpi-r4 dtsiFrank Wunderlich (13):
dt-bindings: net: mediatek,net: update for mt7988
dt-bindings: net: dsa: mediatek,mt7530: add dsa-port definition formt7988dt-bindings: net: dsa: mediatek,mt7530: add internal mdio bus
dt-bindings: interconnect: add mt7988-cci compatible
arm64: dts: mediatek: mt7988: add cci node
arm64: dts: mediatek: mt7988: add basic ethernet-nodes
arm64: dts: mediatek: mt7988: add switch node
arm64: dts: mediatek: mt7988a-bpi-r4: add proc-supply for cci
arm64: dts: mediatek: mt7988a-bpi-r4: drop unused pins
arm64: dts: mediatek: mt7988a-bpi-r4: add gpio leds
arm64: dts: mediatek: mt7988a-bpi-r4: add aliases for ethernet
arm64: dts: mediatek: mt7988a-bpi-r4: add sfp cages and link to gmac
arm64: dts: mediatek: mt7988a-bpi-r4: configure switch phys and leds.../bindings/interconnect/mediatek,cci.yaml | 11 +- .../bindings/net/dsa/mediatek,mt7530.yaml | 24 +- .../devicetree/bindings/net/mediatek,net.yaml | 28 +- .../mediatek/mt7988a-bananapi-bpi-r4-2g5.dts | 11 + .../dts/mediatek/mt7988a-bananapi-bpi-r4.dts | 19 ++ .../dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 198 ++++++----- arch/arm64/boot/dts/mediatek/mt7988a.dtsi | 307 +++++++++++++++++- 7 files changed, 498 insertions(+), 100 deletions(-)
regards Frank