further mt7988 devicetree work
Subsystems (7)
v6 cover further mt7988 devicetree work
From: Frank Wunderlich <[email protected]>
Resend due my linux.dev mailbox stopped sending due to many recipients.
This series continues mt7988 devicetree work
- Extend cpu frequency scaling with CCI
- GPIO leds
- Basic network-support (ethernet controller + builtin switch + SFP Cages)
depencies (i hope this list is complete and latest patches/series linked):
support interrupt-names is optional again as i re-added the reserved IRQs (they are not unusable as i thought and can allow features in future)
https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/
needs change in mtk ethernet driver for the sram to be read from separate node:
https://patchwork.kernel.org/project/netdevbpf/patch/566ca90fc59ad0d3aff8bc8dc22ebaf0544bce47.1751072868.git.daniel@makrotopia.org/
for SFP-Function (macs currently disabled):
PCS clearance which is a 1.5 year discussion currently ongoing
Daniel asked netdev for a way 2 go:
https://lore.kernel.org/netdev/[email protected]/
e.g. something like this (one of):
* https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/ (v6)
* https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/ (v4)
* https://patchwork.kernel.org/project/netdevbpf/patch/ba4e359584a6b3bc4b3470822c42186d5b0856f9.1721910728.git.daniel@makrotopia.org/
full usxgmii driver:
https://patchwork.kernel.org/project/netdevbpf/patch/07845ec900ba41ff992875dce12c622277592c32.1702352117.git.daniel@makrotopia.org/
first PCS-discussion is here:
https://patchwork.kernel.org/project/netdevbpf/patch/8aa905080bdb6760875d62cb3b2b41258837f80e.1702352117.git.daniel@makrotopia.org/
some more here:
https://lore.kernel.org/netdev/[email protected]/
and then dts nodes for sgmiisys+usxgmii+2g5 firmware
when above depencies are solved the mac1/2 can be enabled and 2.5G phy/SFP slots will work.
changes:
v6:
binding:
- split out the interrupt-names into separate patch
- update irq(name) min count to 4
- move interrupt-names up
- add sram-property
- drop second reg entry and minitems as there is only 1 item left
dts:
- fix whitespace-errors for pdma irqs (spaces vs. tabs)
- move sram from eth reg to own sram node (needs CONFIG_SRAM)
v5:
- add reserved irqs and change names
- update binding for 8 irqs with different names (rx,tx => fe1+fe2, rx-ringX => pdmaX) (dropped Robs RB due to this change again, sorry)
v4:
net-binding:
- allow interrupt names and increase max interrupts to 6 because of RSS/LRO interrupts (dropped Robs RB due to this change)
dts-patches:
- add interrupts for RSS/LRO and interrupt-names for ethernet node
- eth-reg and clock whitespace-fix
- comment for fixed-link on gmac0
- drop phy-mode properties as suggested by andrew
- drop phy-connection-type on 2g5 board
- reorder some properties
- update 2g5 phy node
- unit-name dec instead of hex to match reg property
- move compatible before reg
- drop phy-mode
v3:
- dropped patches already applied (SPI+thermal)
- added soc specific cci compatible (new binding patch + changed dts)
- enable 2g5 phy because driver is now merged
- add patch for cleaning up unnecessary pins
- add patch for gpio-leds
- add patch for adding ethernet aliases
v2:
- change reg to list of items in eth binding
- changed mt7530 binding:
- unevaluatedProperties=false
- mediatek,pio subproperty
- from patternProperty to property
- board specific properties like led function and labels moved to bpi-r4 dtsi
Frank Wunderlich (15):
dt-bindings: net: mediatek,net: update for mt7988
dt-bindings: net: mediatek,net: allow irq names
dt-bindings: net: mediatek,net: update for mt7988
dt-bindings: net: dsa: mediatek,mt7530: add dsa-port definition for
mt7988
dt-bindings: net: dsa: mediatek,mt7530: add internal mdio bus
dt-bindings: interconnect: add mt7988-cci compatible
arm64: dts: mediatek: mt7988: add cci node
arm64: dts: mediatek: mt7988: add basic ethernet-nodes
arm64: dts: mediatek: mt7988: add switch node
arm64: dts: mediatek: mt7988a-bpi-r4: add proc-supply for cci
arm64: dts: mediatek: mt7988a-bpi-r4: drop unused pins
arm64: dts: mediatek: mt7988a-bpi-r4: add gpio leds
arm64: dts: mediatek: mt7988a-bpi-r4: add aliases for ethernet
arm64: dts: mediatek: mt7988a-bpi-r4: add sfp cages and link to gmac
arm64: dts: mediatek: mt7988a-bpi-r4: configure switch phys and leds
.../bindings/interconnect/mediatek,cci.yaml | 11 +- .../bindings/net/dsa/mediatek,mt7530.yaml | 24 +- .../devicetree/bindings/net/mediatek,net.yaml | 47 ++- .../mediatek/mt7988a-bananapi-bpi-r4-2g5.dts | 11 + .../dts/mediatek/mt7988a-bananapi-bpi-r4.dts | 19 ++ .../dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 198 ++++++----- arch/arm64/boot/dts/mediatek/mt7988a.dtsi | 318 +++++++++++++++++- 7 files changed, 529 insertions(+), 99 deletions(-)
Signature · 1 line
2.43.0
PATCH v6 1/15 dt-bindings: net: mediatek,net: update for mt7988
From: Frank Wunderlich <[email protected]>
Update binding for mt7988 which has 3 gmac and a sram for dma operations.
MT7988 has 4 FE IRQs (currently only 2 are used) and 4 IRQs for use with RSS/LRO later.
Add interrupt-names to make them accessible by name.
---
v6:
- update irq(name) min count to 4
- move interrupt-names up and limiting for all socs below
- add sram-property and drop second reg entry
- drop minitems as there is only 1 item left now
v5:
- fix v4 logmessage and change description a bit describing how i get the irq count.
- update binding for 8 irqs with different names (rx,tx => fe0..fe3) including the 2 reserved irqs which can be used later
- change rx-ringX to pdmaX to be closer to hardware documentation
v4:
- increase max interrupts to 6 because of adding RSS/LRO interrupts (4) and dropping 2 reserved irqs (0+3) around rx+tx
- dropped Robs RB due to this change
- allow interrupt names
- add interrupt-names without reserved IRQs on mt7988
this requires mtk driver patch:
https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/
v2:
- change reg to list of items
--- .../devicetree/bindings/net/mediatek,net.yaml | 47 +++++++++++++++++-- 1 file changed, 44 insertions(+), 3 deletions(-)
Documentation/devicetree/bindings/net/mediatek,net.yaml +44 -3
@@ -28,7 +28,8 @@ properties: - ralink,rt5350-eth reg: - maxItems: 1 + items: + - description: Register for accessing the MACs. clocks: minItems: 2
@@ -40,7 +41,19 @@ properties: interrupts: minItems: 1 - maxItems: 4 + maxItems: 8 + + interrupt-names: + minItems: 1 + items: + - const: fe0 + - const: fe1 + - const: fe2 + - const: fe3 + - const: pdma0 + - const: pdma1 + - const: pdma2 + - const: pdma3 power-domains: maxItems: 1
@@ -54,6 +67,10 @@ properties: - const: gmac - const: ppe + sram: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to mmio SRAM + mediatek,ethsys: $ref: /schemas/types.yaml#/definitions/phandle description:
@@ -135,6 +152,10 @@ allOf: minItems: 3 maxItems: 3 + interrupt-names: + minItems: 3 + maxItems: 3 + clocks: minItems: 4 maxItems: 4
@@ -166,6 +187,9 @@ allOf: interrupts: maxItems: 1 + interrupt-namess: + maxItems: 1 + clocks: minItems: 2 maxItems: 2
@@ -192,6 +216,10 @@ allOf: minItems: 3 maxItems: 3 + interrupt-names: + minItems: 3 + maxItems: 3 + clocks: minItems: 11 maxItems: 11
@@ -232,6 +260,10 @@ allOf: minItems: 3 maxItems: 3 + interrupt-names: + minItems: 3 + maxItems: 3 + clocks: minItems: 17 maxItems: 17
@@ -274,6 +306,9 @@ allOf: interrupts: minItems: 4 + interrupt-names: + minItems: 4 + clocks: minItems: 15 maxItems: 15
@@ -312,6 +347,9 @@ allOf: interrupts: minItems: 4 + interrupt-names: + minItems: 4 + clocks: minItems: 15 maxItems: 15
@@ -350,6 +388,9 @@ allOf: interrupts: minItems: 4 + interrupt-names: + minItems: 4 + clocks: minItems: 24 maxItems: 24
@@ -382,7 +423,7 @@ allOf: - const: xgp3 patternProperties: - "^mac@[0-1]$": + "^mac@[0-2]$": type: object unevaluatedProperties: false allOf:
Signature · 1 line
2.43.0
PATCH v6 2/15 dt-bindings: net: mediatek,net: allow irq names
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
In preparation for MT7988 and RSS/LRO allow the interrupt-names property. Also increase the maximum IRQ count to 8 (4 FE + 4 RSS), but set boundaries for all compatibles same as irq count.
---
v6: new patch splitted from the mt7988 changes
--- Documentation/devicetree/bindings/net/mediatek,net.yaml | 9 ++------- 1 file changed, 2 insertions(+), 7 deletions(-)
Documentation/devicetree/bindings/net/mediatek,net.yaml +2 -7
@@ -28,8 +28,7 @@ properties: - ralink,rt5350-eth reg: - items: - - description: Register for accessing the MACs. + maxItems: 1 clocks: minItems: 2
@@ -67,10 +66,6 @@ properties: - const: gmac - const: ppe - sram: - $ref: /schemas/types.yaml#/definitions/phandle - description: phandle to mmio SRAM - mediatek,ethsys: $ref: /schemas/types.yaml#/definitions/phandle description:
@@ -423,7 +418,7 @@ allOf: - const: xgp3 patternProperties: - "^mac@[0-2]$": + "^mac@[0-1]$": type: object unevaluatedProperties: false allOf:
Signature · 1 line
2.43.0
PATCH v6 3/15 dt-bindings: net: mediatek,net: update for mt7988
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Update binding for mt7988 which has 3 gmac and a sram for dma operations.
MT7988 has 4 FE IRQs (currently only 2 are used) and 4 IRQs for use with RSS/LRO later.
---
v6:
- split out the interrupt-names into separate patch
- update irq(name) min count to 4
- add sram-property
- drop second reg entry and minitems as there is only 1 item left again
v5:
- fix v4 logmessage and change description a bit describing how i get the irq count.
- update binding for 8 irqs with different names (rx,tx => fe0..fe3) including the 2 reserved irqs which can be used later
- change rx-ringX to pdmaX to be closer to hardware documentation
v4:
- increase max interrupts to 6 because of adding RSS/LRO interrupts (4) and dropping 2 reserved irqs (0+3) around rx+tx
- dropped Robs RB due to this change
- allow interrupt names
- add interrupt-names without reserved IRQs on mt7988
this requires mtk driver patch:
https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/
v2:
- change reg to list of items
--- Documentation/devicetree/bindings/net/mediatek,net.yaml | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-)
Documentation/devicetree/bindings/net/mediatek,net.yaml +7 -2
@@ -28,7 +28,8 @@ properties: - ralink,rt5350-eth reg: - maxItems: 1 + items: + - description: Register for accessing the MACs. clocks: minItems: 2
@@ -66,6 +67,10 @@ properties: - const: gmac - const: ppe + sram: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to mmio SRAM + mediatek,ethsys: $ref: /schemas/types.yaml#/definitions/phandle description:
@@ -418,7 +423,7 @@ allOf: - const: xgp3 patternProperties: - "^mac@[0-1]$": + "^mac@[0-2]$": type: object unevaluatedProperties: false allOf:
Signature · 1 line
2.43.0
PATCH v6 4/15 dt-bindings: net: dsa: mediatek,mt7530: add dsa-port definition for mt7988
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add own dsa-port binding for SoC with internal switch where only phy-mode 'internal' is valid.
--- .../bindings/net/dsa/mediatek,mt7530.yaml | 14 +++++++++++++- 1 file changed, 13 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml +13 -1
@@ -190,6 +190,18 @@ required: - reg $defs: + builtin-dsa-port: + patternProperties: + "^(ethernet-)?ports$": + patternProperties: + "^(ethernet-)?port@[0-6]$": + if: + required: [ ethernet ] + then: + properties: + phy-mode: + const: internal + mt7530-dsa-port: patternProperties: "^(ethernet-)?ports$":
@@ -297,7 +309,7 @@ allOf: - airoha,en7581-switch - airoha,an7583-switch then: - $ref: "#/$defs/mt7530-dsa-port" + $ref: "#/$defs/builtin-dsa-port" properties: gpio-controller: false mediatek,mcm: false
Signature · 1 line
2.43.0
PATCH v6 5/15 dt-bindings: net: dsa: mediatek,mt7530: add internal mdio bus
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Mt7988 buildin switch has own mdio bus where ge-phys are connected. Add related property for this.
---
v2:
- change from patternproperty to property
- add unevaluatedProperties and mediatek,pio subproperty
--- .../devicetree/bindings/net/dsa/mediatek,mt7530.yaml | 10 ++++++++++ 1 file changed, 10 insertions(+)
Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml +10 -0
@@ -136,6 +136,16 @@ properties: See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt for details for the regulator setup on these boards. + mdio: + $ref: /schemas/net/mdio.yaml# + unevaluatedProperties: false + + properties: + mediatek,pio: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle pointing to the mediatek pinctrl node. + mediatek,mcm: type: boolean description:
Signature · 1 line
2.43.0
PATCH v6 6/15 dt-bindings: interconnect: add mt7988-cci compatible
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add compatible for Mediatek MT7988 SoC with mediatek,mt8183-cci fallback which is taken by driver.
---
v2:
- no RFC
- drop "items" as sugested by conor
--- .../bindings/interconnect/mediatek,cci.yaml | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-)
Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml +8 -3
@@ -17,9 +17,14 @@ description: | properties: compatible: - enum: - - mediatek,mt8183-cci - - mediatek,mt8186-cci + oneOf: + - enum: + - mediatek,mt8183-cci + - mediatek,mt8186-cci + - items: + - enum: + - mediatek,mt7988-cci + - const: mediatek,mt8183-cci clocks: items:
Signature · 1 line
2.43.0
PATCH v6 7/15 arm64: dts: mediatek: mt7988: add cci node
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add cci devicetree node for cpu frequency scaling.
---
v3:
- add mt7988-cci compatible as suggested by angelo
--- arch/arm64/boot/dts/mediatek/mt7988a.dtsi | 33 +++++++++++++++++++++++ 1 file changed, 33 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a.dtsi +33 -0
@@ -12,6 +12,35 @@ / { #address-cells = <2>; #size-cells = <2>; + cci: cci { + compatible = "mediatek,mt7988-cci", "mediatek,mt8183-cci"; + clocks = <&mcusys CLK_MCU_BUS_DIV_SEL>, + <&topckgen CLK_TOP_XTAL>; + clock-names = "cci", "intermediate"; + operating-points-v2 = <&cci_opp>; + }; + + cci_opp: opp-table-cci { + compatible = "operating-points-v2"; + opp-shared; + opp-480000000 { + opp-hz = /bits/ 64 <480000000>; + opp-microvolt = <850000>; + }; + opp-660000000 { + opp-hz = /bits/ 64 <660000000>; + opp-microvolt = <850000>; + }; + opp-900000000 { + opp-hz = /bits/ 64 <900000000>; + opp-microvolt = <850000>; + }; + opp-1080000000 { + opp-hz = /bits/ 64 <1080000000>; + opp-microvolt = <900000>; + }; + }; + cpus { #address-cells = <1>; #size-cells = <0>;
@@ -25,6 +54,7 @@ cpu0: cpu@0 { <&topckgen CLK_TOP_XTAL>; clock-names = "cpu", "intermediate"; operating-points-v2 = <&cluster0_opp>; + mediatek,cci = <&cci>; }; cpu1: cpu@1 {
@@ -36,6 +66,7 @@ cpu1: cpu@1 { <&topckgen CLK_TOP_XTAL>; clock-names = "cpu", "intermediate"; operating-points-v2 = <&cluster0_opp>; + mediatek,cci = <&cci>; }; cpu2: cpu@2 {
@@ -47,6 +78,7 @@ cpu2: cpu@2 { <&topckgen CLK_TOP_XTAL>; clock-names = "cpu", "intermediate"; operating-points-v2 = <&cluster0_opp>; + mediatek,cci = <&cci>; }; cpu3: cpu@3 {
@@ -58,6 +90,7 @@ cpu3: cpu@3 { <&topckgen CLK_TOP_XTAL>; clock-names = "cpu", "intermediate"; operating-points-v2 = <&cluster0_opp>; + mediatek,cci = <&cci>; }; cluster0_opp: opp-table-0 {
Signature · 1 line
2.43.0
PATCH v6 8/15 arm64: dts: mediatek: mt7988: add basic ethernet-nodes
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add basic ethernet related nodes.
Mac1+2 needs pcs (sgmii+usxgmii) to work correctly which will be linked later when driver is merged.
---
v6:
- fix whitespace-errors for pdma irqs (spaces vs. tabs)
- move sram from eth reg to own sram node (needs CONFIG_SRAM)
v5:
- add reserved irqs and change names to fe0..fe3
- change rx-ringX to pdmaX to be closer to documentation
v4:
- comment for fixed-link on gmac0
- update 2g5 phy node
- unit-name dec instead of hex to match reg property
- move compatible before reg
- drop phy-mode
- add interrupts for RSS
- add interrupt-names and drop reserved irqs for ethernet
- some reordering
- eth-reg and clock whitespace-fix based on angelos review
--- arch/arm64/boot/dts/mediatek/mt7988a.dtsi | 137 +++++++++++++++++++++- 1 file changed, 134 insertions(+), 3 deletions(-)
arch/arm64/boot/dts/mediatek/mt7988a.dtsi +134 -3
@@ -680,7 +680,28 @@ xphyu3port0: usb-phy@11e13000 { }; }; - clock-controller@11f40000 { + xfi_tphy0: phy@11f20000 { + compatible = "mediatek,mt7988-xfi-tphy"; + reg = <0 0x11f20000 0 0x10000>; + clocks = <&xfi_pll CLK_XFIPLL_PLL_EN>, + <&topckgen CLK_TOP_XFI_PHY_0_XTAL_SEL>; + clock-names = "xfipll", "topxtal"; + resets = <&watchdog 14>; + mediatek,usxgmii-performance-errata; + #phy-cells = <0>; + }; + + xfi_tphy1: phy@11f30000 { + compatible = "mediatek,mt7988-xfi-tphy"; + reg = <0 0x11f30000 0 0x10000>; + clocks = <&xfi_pll CLK_XFIPLL_PLL_EN>, + <&topckgen CLK_TOP_XFI_PHY_1_XTAL_SEL>; + clock-names = "xfipll", "topxtal"; + resets = <&watchdog 15>; + #phy-cells = <0>; + }; + + xfi_pll: clock-controller@11f40000 { compatible = "mediatek,mt7988-xfi-pll"; reg = <0 0x11f40000 0 0x1000>; resets = <&watchdog 16>;
@@ -714,19 +735,129 @@ phy_calibration_p3: calib@97c { }; }; - clock-controller@15000000 { + ethsys: clock-controller@15000000 { compatible = "mediatek,mt7988-ethsys", "syscon"; reg = <0 0x15000000 0 0x1000>; #clock-cells = <1>; #reset-cells = <1>; }; - clock-controller@15031000 { + ethwarp: clock-controller@15031000 { compatible = "mediatek,mt7988-ethwarp"; reg = <0 0x15031000 0 0x1000>; #clock-cells = <1>; #reset-cells = <1>; }; + + eth: ethernet@15100000 { + compatible = "mediatek,mt7988-eth"; + reg = <0 0x15100000 0 0x80000>; + interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "fe0", "fe1", "fe2", "fe3", "pdma0", + "pdma1", "pdma2", "pdma3"; + clocks = <ðsys CLK_ETHDMA_CRYPT0_EN>, + <ðsys CLK_ETHDMA_FE_EN>, + <ðsys CLK_ETHDMA_GP2_EN>, + <ðsys CLK_ETHDMA_GP1_EN>, + <ðsys CLK_ETHDMA_GP3_EN>, + <ðwarp CLK_ETHWARP_WOCPU2_EN>, + <ðwarp CLK_ETHWARP_WOCPU1_EN>, + <ðwarp CLK_ETHWARP_WOCPU0_EN>, + <ðsys CLK_ETHDMA_ESW_EN>, + <&topckgen CLK_TOP_ETH_GMII_SEL>, + <&topckgen CLK_TOP_ETH_REFCK_50M_SEL>, + <&topckgen CLK_TOP_ETH_SYS_200M_SEL>, + <&topckgen CLK_TOP_ETH_SYS_SEL>, + <&topckgen CLK_TOP_ETH_XGMII_SEL>, + <&topckgen CLK_TOP_ETH_MII_SEL>, + <&topckgen CLK_TOP_NETSYS_SEL>, + <&topckgen CLK_TOP_NETSYS_500M_SEL>, + <&topckgen CLK_TOP_NETSYS_PAO_2X_SEL>, + <&topckgen CLK_TOP_NETSYS_SYNC_250M_SEL>, + <&topckgen CLK_TOP_NETSYS_PPEFB_250M_SEL>, + <&topckgen CLK_TOP_NETSYS_WARP_SEL>, + <ðsys CLK_ETHDMA_XGP1_EN>, + <ðsys CLK_ETHDMA_XGP2_EN>, + <ðsys CLK_ETHDMA_XGP3_EN>; + clock-names = "crypto", "fe", "gp2", "gp1", "gp3", + "ethwarp_wocpu2", "ethwarp_wocpu1", + "ethwarp_wocpu0", "esw", "top_eth_gmii_sel", + "top_eth_refck_50m_sel", "top_eth_sys_200m_sel", + "top_eth_sys_sel", "top_eth_xgmii_sel", + "top_eth_mii_sel", "top_netsys_sel", + "top_netsys_500m_sel", "top_netsys_pao_2x_sel", + "top_netsys_sync_250m_sel", + "top_netsys_ppefb_250m_sel", + "top_netsys_warp_sel","xgp1", "xgp2", "xgp3"; + assigned-clocks = <&topckgen CLK_TOP_NETSYS_2X_SEL>, + <&topckgen CLK_TOP_NETSYS_GSW_SEL>, + <&topckgen CLK_TOP_USXGMII_SBUS_0_SEL>, + <&topckgen CLK_TOP_USXGMII_SBUS_1_SEL>, + <&topckgen CLK_TOP_SGM_0_SEL>, + <&topckgen CLK_TOP_SGM_1_SEL>; + assigned-clock-parents = <&apmixedsys CLK_APMIXED_NET2PLL>, + <&topckgen CLK_TOP_NET1PLL_D4>, + <&topckgen CLK_TOP_NET1PLL_D8_D4>, + <&topckgen CLK_TOP_NET1PLL_D8_D4>, + <&apmixedsys CLK_APMIXED_SGMPLL>, + <&apmixedsys CLK_APMIXED_SGMPLL>; + sram = <ð_sram>; + #address-cells = <1>; + #size-cells = <0>; + mediatek,ethsys = <ðsys>; + mediatek,infracfg = <&topmisc>; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "internal"; + + /* Connected to internal switch */ + fixed-link { + speed = <10000>; + full-duplex; + pause; + }; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + status = "disabled"; + }; + + gmac2: mac@2 { + compatible = "mediatek,eth-mac"; + reg = <2>; + status = "disabled"; + }; + + mdio_bus: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + + /* internal 2.5G PHY */ + int_2p5g_phy: ethernet-phy@15 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <15>; + }; + }; + }; + + eth_sram: sram@15400000 { + compatible = "mmio-sram"; + reg = <0 0x15400000 0 0x200000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x15400000 0 0x200000>; + }; }; thermal-zones {
Signature · 1 line
2.43.0
PATCH v6 9/15 arm64: dts: mediatek: mt7988: add switch node
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add mt7988 builtin mt753x switch nodes.
---
v4:
- drop phy-mode for gsw-phy
- reorder phy-mode after phy-handle
- drop interrupt parent from switch
v2:
- drop labels and led-function too (have to be in board)
--- arch/arm64/boot/dts/mediatek/mt7988a.dtsi | 148 ++++++++++++++++++++++ 1 file changed, 148 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a.dtsi +148 -0
@@ -742,6 +742,154 @@ ethsys: clock-controller@15000000 { #reset-cells = <1>; }; + switch: switch@15020000 { + compatible = "mediatek,mt7988-switch"; + reg = <0 0x15020000 0 0x8000>; + interrupt-controller; + #interrupt-cells = <1>; + interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; + resets = <ðwarp MT7988_ETHWARP_RST_SWITCH>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + gsw_port0: port@0 { + reg = <0>; + phy-handle = <&gsw_phy0>; + phy-mode = "internal"; + }; + + gsw_port1: port@1 { + reg = <1>; + phy-handle = <&gsw_phy1>; + phy-mode = "internal"; + }; + + gsw_port2: port@2 { + reg = <2>; + phy-handle = <&gsw_phy2>; + phy-mode = "internal"; + }; + + gsw_port3: port@3 { + reg = <3>; + phy-handle = <&gsw_phy3>; + phy-mode = "internal"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "internal"; + + fixed-link { + speed = <10000>; + full-duplex; + pause; + }; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + mediatek,pio = <&pio>; + + gsw_phy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + interrupts = <0>; + nvmem-cells = <&phy_calibration_p0>; + nvmem-cell-names = "phy-cal-data"; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + gsw_phy0_led0: led@0 { + reg = <0>; + status = "disabled"; + }; + + gsw_phy0_led1: led@1 { + reg = <1>; + status = "disabled"; + }; + }; + }; + + gsw_phy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + interrupts = <1>; + nvmem-cells = <&phy_calibration_p1>; + nvmem-cell-names = "phy-cal-data"; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + gsw_phy1_led0: led@0 { + reg = <0>; + status = "disabled"; + }; + + gsw_phy1_led1: led@1 { + reg = <1>; + status = "disabled"; + }; + }; + }; + + gsw_phy2: ethernet-phy@2 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <2>; + interrupts = <2>; + nvmem-cells = <&phy_calibration_p2>; + nvmem-cell-names = "phy-cal-data"; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + gsw_phy2_led0: led@0 { + reg = <0>; + status = "disabled"; + }; + + gsw_phy2_led1: led@1 { + reg = <1>; + status = "disabled"; + }; + }; + }; + + gsw_phy3: ethernet-phy@3 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <3>; + interrupts = <3>; + nvmem-cells = <&phy_calibration_p3>; + nvmem-cell-names = "phy-cal-data"; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + gsw_phy3_led0: led@0 { + reg = <0>; + status = "disabled"; + }; + + gsw_phy3_led1: led@1 { + reg = <1>; + status = "disabled"; + }; + }; + }; + }; + }; + ethwarp: clock-controller@15031000 { compatible = "mediatek,mt7988-ethwarp"; reg = <0 0x15031000 0 0x1000>;
Signature · 1 line
2.43.0
PATCH v6 10/15 arm64: dts: mediatek: mt7988a-bpi-r4: add proc-supply for cci
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
CCI requires proc-supply. Add it on board level.
--- arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 4 ++++ 1 file changed, 4 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi +4 -0
@@ -40,6 +40,10 @@ reg_3p3v: regulator-3p3v { }; }; +&cci { + proc-supply = <&rt5190_buck3>; +}; + &cpu0 { proc-supply = <&rt5190_buck3>; };
Signature · 1 line
2.43.0
PATCH v6 11/15 arm64: dts: mediatek: mt7988a-bpi-r4: drop unused pins
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Pins were moved from SoC dtsi to Board level dtsi without cleaning up to needed ones. Drop the unused pins now.
--- .../dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 89 ------------------- 1 file changed, 89 deletions(-)
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi +0 -89
@@ -223,18 +223,6 @@ &pcie3 { }; &pio { - mdio0_pins: mdio0-pins { - mux { - function = "eth"; - groups = "mdc_mdio0"; - }; - - conf { - pins = "SMI_0_MDC", "SMI_0_MDIO"; - drive-strength = <8>; - }; - }; - i2c0_pins: i2c0-g0-pins { mux { function = "i2c";
@@ -249,20 +237,6 @@ mux { }; }; - i2c1_sfp_pins: i2c1-sfp-g0-pins { - mux { - function = "i2c"; - groups = "i2c1_sfp"; - }; - }; - - i2c2_0_pins: i2c2-g0-pins { - mux { - function = "i2c"; - groups = "i2c2_0"; - }; - }; - i2c2_1_pins: i2c2-g1-pins { mux { function = "i2c";
@@ -298,34 +272,6 @@ mux { }; }; - gbe0_led1_pins: gbe0-led1-pins { - mux { - function = "led"; - groups = "gbe0_led1"; - }; - }; - - gbe1_led1_pins: gbe1-led1-pins { - mux { - function = "led"; - groups = "gbe1_led1"; - }; - }; - - gbe2_led1_pins: gbe2-led1-pins { - mux { - function = "led"; - groups = "gbe2_led1"; - }; - }; - - gbe3_led1_pins: gbe3-led1-pins { - mux { - function = "led"; - groups = "gbe3_led1"; - }; - }; - i2p5gbe_led0_pins: 2p5gbe-led0-pins { mux { function = "led";
@@ -333,13 +279,6 @@ mux { }; }; - i2p5gbe_led1_pins: 2p5gbe-led1-pins { - mux { - function = "led"; - groups = "2p5gbe_led1"; - }; - }; - mmc0_pins_emmc_45: mmc0-emmc-45-pins { mux { function = "flash";
@@ -361,40 +300,12 @@ mux { }; }; - snfi_pins: snfi-pins { - mux { - function = "flash"; - groups = "snfi"; - }; - }; - - spi0_pins: spi0-pins { - mux { - function = "spi"; - groups = "spi0"; - }; - }; - spi0_flash_pins: spi0-flash-pins { mux { function = "spi"; groups = "spi0", "spi0_wp_hold"; }; }; - - spi2_pins: spi2-pins { - mux { - function = "spi"; - groups = "spi2"; - }; - }; - - spi2_flash_pins: spi2-flash-pins { - mux { - function = "spi"; - groups = "spi2", "spi2_wp_hold"; - }; - }; }; &pwm {
Signature · 1 line
2.43.0
PATCH v6 12/15 arm64: dts: mediatek: mt7988a-bpi-r4: add gpio leds
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Bananapi R4 has a green and a blue led which can be switched by gpio. Green led is for running state so default on.
Green led also shares pin with eeprom writeprotect where led off allows writing to eeprom.
--- .../dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi +19 -0
@@ -21,6 +21,25 @@ fan: pwm-fan { status = "okay"; }; + gpio-leds { + compatible = "gpio-leds"; + + led_green: led-green { + function = LED_FUNCTION_STATUS; + color = <LED_COLOR_ID_GREEN>; + gpios = <&pio 79 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + led_blue: led-blue { + function = LED_FUNCTION_WPS; + color = <LED_COLOR_ID_BLUE>; + gpios = <&pio 63 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + reg_1p8v: regulator-1p8v { compatible = "regulator-fixed"; regulator-name = "fixed-1.8V";
Signature · 1 line
2.43.0
PATCH v6 13/15 arm64: dts: mediatek: mt7988a-bpi-r4: add aliases for ethernet
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add aliases for gmacs to allow bootloader setting mac-adresses.
--- arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 6 ++++++ 1 file changed, 6 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi +6 -0
@@ -8,6 +8,12 @@ #include "mt7988a.dtsi" / { + aliases { + ethernet0 = &gmac0; + ethernet1 = &gmac1; + ethernet2 = &gmac2; + }; + chosen { stdout-path = "serial0:115200n8"; };
Signature · 1 line
2.43.0
PATCH v6 14/15 arm64: dts: mediatek: mt7988a-bpi-r4: add sfp cages and link to gmac
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Add SFP cages to Bananapi-R4 board. The 2.5g phy variant only contains the wan-SFP, so add this to common dtsi and the lan-sfp only to the dual-SFP variant.
---
v4:
- update 2g5-board (reorder and drop phy-connection-type)
- order sfp properties
v3:
- enable mac with 2.5g phy on r4 phy variant because driver is now mainline
--- .../mediatek/mt7988a-bananapi-bpi-r4-2g5.dts | 11 +++++++++++ .../dts/mediatek/mt7988a-bananapi-bpi-r4.dts | 19 +++++++++++++++++++ .../dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 19 +++++++++++++++++++ 3 files changed, 49 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4-2g5.dts +11 -0
@@ -9,3 +9,14 @@ / { model = "Banana Pi BPI-R4 (1x SFP+, 1x 2.5GbE)"; chassis-type = "embedded"; }; + +&gmac1 { + phy = <&int_2p5g_phy>; + phy-mode = "internal"; + status = "okay"; +}; + +&int_2p5g_phy { + pinctrl-0 = <&i2p5gbe_led0_pins>; + pinctrl-names = "i2p5gbe-led"; +};
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dts +19 -0
@@ -8,6 +8,25 @@ / { compatible = "bananapi,bpi-r4", "mediatek,mt7988a"; model = "Banana Pi BPI-R4 (2x SFP+)"; chassis-type = "embedded"; + + /* SFP2 cage (LAN) */ + sfp2: sfp2 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp2>; + maximum-power-milliwatt = <3000>; + + los-gpios = <&pio 2 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&pio 83 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&pio 3 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&pio 0 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&pio 1 GPIO_ACTIVE_HIGH>; + }; +}; + +&gmac1 { + managed = "in-band-status"; + phy-mode = "usxgmii"; + sfp = <&sfp2>; }; &pca9545 {
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi +19 -0
@@ -63,6 +63,19 @@ reg_3p3v: regulator-3p3v { regulator-boot-on; regulator-always-on; }; + + /* SFP1 cage (WAN) */ + sfp1: sfp1 { + compatible = "sff,sfp"; + i2c-bus = <&i2c_sfp1>; + maximum-power-milliwatt = <3000>; + + los-gpios = <&pio 54 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&pio 82 GPIO_ACTIVE_LOW>; + rate-select0-gpios = <&pio 21 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&pio 70 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&pio 69 GPIO_ACTIVE_HIGH>; + }; }; &cci {
@@ -133,6 +146,12 @@ map-cpu-active-low { }; }; +&gmac2 { + managed = "in-band-status"; + phy-mode = "usxgmii"; + sfp = <&sfp1>; +}; + &i2c0 { pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins>;
Signature · 1 line
2.43.0
PATCH v6 15/15 arm64: dts: mediatek: mt7988a-bpi-r4: configure switch phys and leds
In reply to Frank WunderlichFrom: Frank Wunderlich <[email protected]>
Assign pinctrl to switch phys and leds.
---
v4:
- reorder switch phy(-led) properties
v2:
- add labels and led-function and include after dropping from soc dtsi
--- .../dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 61 +++++++++++++++++++ 1 file changed, 61 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi +61 -0
@@ -4,6 +4,7 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/regulator/richtek,rt5190a-regulator.h> +#include <dt-bindings/leds/common.h> #include "mt7988a.dtsi"
@@ -152,6 +153,66 @@ &gmac2 { sfp = <&sfp1>; }; +&gsw_phy0 { + pinctrl-0 = <&gbe0_led0_pins>; + pinctrl-names = "gbe-led"; +}; + +&gsw_phy0_led0 { + function = LED_FUNCTION_WAN; + color = <LED_COLOR_ID_GREEN>; + status = "okay"; +}; + +&gsw_port0 { + label = "wan"; +}; + +&gsw_phy1 { + pinctrl-0 = <&gbe1_led0_pins>; + pinctrl-names = "gbe-led"; +}; + +&gsw_phy1_led0 { + function = LED_FUNCTION_LAN; + color = <LED_COLOR_ID_GREEN>; + status = "okay"; +}; + +&gsw_port1 { + label = "lan1"; +}; + +&gsw_phy2 { + pinctrl-0 = <&gbe2_led0_pins>; + pinctrl-names = "gbe-led"; +}; + +&gsw_phy2_led0 { + function = LED_FUNCTION_LAN; + color = <LED_COLOR_ID_GREEN>; + status = "okay"; +}; + +&gsw_port2 { + label = "lan2"; +}; + +&gsw_phy3 { + pinctrl-0 = <&gbe3_led0_pins>; + pinctrl-names = "gbe-led"; +}; + +&gsw_phy3_led0 { + function = LED_FUNCTION_LAN; + color = <LED_COLOR_ID_GREEN>; + status = "okay"; +}; + +&gsw_port3 { + label = "lan3"; +}; + &i2c0 { pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins>;
Signature · 1 line
2.43.0