Skip to contentSkip to conversation

remoteproc: imx_rproc: allow attaching to running core kicked by the bootloader

PATCH In review Hiago De Franco 3 participants 14 messages Jun 29, 2025 – Jul 16, 2025

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

v7 cover remoteproc: imx_rproc: allow attaching to running core kicked by the bootloader

From: Hiago De Franco <[email protected]>

This patch series depends on Ulf's patches that are currently under review, "pmdomain: Add generic ->sync_state() support to genpd" [1]. Without them, this series is not going to work.

For the i.MX8X and i.MX8 family SoCs, currently when the remotecore is started by the bootloader and the M core and A core are in the same partition, the driver is not capable to detect the remote core and report the correct state of it.

This patch series implement a new function, dev_pm_genpd_is_on(), which returns the power status of a given power domain (M core power domains IMX_SC_R_M4_0_PID0 and IMX_SC_R_M4_0_MU_1A in this case). If it is already powered on, the driver will attach to it.

Finally, the imx_rproc_clk_enable() function was also changed to make it return before dev_clk_get() is called, as it currently generates an SCU fault reset if the remote core is already running and the kernel tries to enable the clock again. These changes are a follow up from a v1 sent to imx_rproc [2] and from a reported regression [3].

[1] https://lore.kernel.org/all/[email protected]/
[2] https://lore.kernel.org/lkml/[email protected]/
[3] https://lore.kernel.org/lkml/20250404141713.ac2ntcsjsf7epdfa@hiago-nb/

v7:
- Added Peng reviewed-by.
v6:
- https://lore.kernel.org/all/[email protected]/
v5:
- https://lore.kernel.org/all/[email protected]/
v4:
- https://lore.kernel.org/lkml/[email protected]/
v3:
- https://lore.kernel.org/all/[email protected]/
v2:
- https://lore.kernel.org/lkml/[email protected]/
v1:
- https://lore.kernel.org/lkml/[email protected]/

Hiago De Franco (3):
pmdomain: core: introduce dev_pm_genpd_is_on()
remoteproc: imx_rproc: skip clock enable when M-core is managed by the
SCU
remoteproc: imx_rproc: detect and attach to pre-booted remote cores

 drivers/pmdomain/core.c        | 33 +++++++++++++++++++++++++++
 drivers/remoteproc/imx_rproc.c | 41 ++++++++++++++++++++++++++++------
 include/linux/pm_domain.h      |  6 +++++
 3 files changed, 73 insertions(+), 7 deletions(-)
Signature · 1 line
2.39.5
#1 lore raw

PATCH v7 1/3 pmdomain: core: introduce dev_pm_genpd_is_on()

From: Hiago De Franco <[email protected]>

This helper function returns the current power status of a given generic power domain.

As example, remoteproc/imx_rproc.c can now use this function to check the power status of the remote core to properly set "attached" or "offline" modes.

---
v6 -> v7:
- Added Peng reviewed-by.
v5 -> v6:
- Added Bjorn reviewed-by.
v4 -> v5:
- s/dev_pm_genpd_is_on/dev_pm_genpd_is_on()/ in function description.
- Updated function description to be explicit the function reflects the current power status and that this might change after the function returns, especially if the genpd is shared.

v3 -> v4:
- New patch.

---
 drivers/pmdomain/core.c   | 33 +++++++++++++++++++++++++++++++++
 include/linux/pm_domain.h |  6 ++++++
 2 files changed, 39 insertions(+)
drivers/pmdomain/core.c +33 -0
index ff5c7f2b69ce..2f387e15cb75 100644
@@ -758,6 +758,39 @@ int dev_pm_genpd_rpm_always_on(struct device *dev, bool on)
 }
 EXPORT_SYMBOL_GPL(dev_pm_genpd_rpm_always_on);
 
+/**
+ * dev_pm_genpd_is_on() - Get device's current power domain status
+ *
+ * @dev: Device to get the current power status
+ *
+ * This function checks whether the generic power domain associated with the
+ * given device is on or not by verifying if genpd_status_on equals
+ * GENPD_STATE_ON.
+ *
+ * Note: this function returns the power status of the genpd at the time of the
+ * call. The power status may change after due to activity from other devices
+ * sharing the same genpd. Therefore, this information should not be relied for
+ * long-term decisions about the device power state.
+ *
+ * Return: 'true' if the device's power domain is on, 'false' otherwise.
+ */
+bool dev_pm_genpd_is_on(struct device *dev)
+{
+	struct generic_pm_domain *genpd;
+	bool is_on;
+
+	genpd = dev_to_genpd_safe(dev);
+	if (!genpd)
+		return false;
+
+	genpd_lock(genpd);
+	is_on = genpd_status_on(genpd);
+	genpd_unlock(genpd);
+
+	return is_on;
+}
+EXPORT_SYMBOL_GPL(dev_pm_genpd_is_on);
+
 /**
  * pm_genpd_inc_rejected() - Adjust the rejected/usage counts for an idle-state.
  *
include/linux/pm_domain.h +6 -0
index 0b18160901a2..c12580b6579b 100644
@@ -301,6 +301,7 @@ void dev_pm_genpd_synced_poweroff(struct device *dev);
 int dev_pm_genpd_set_hwmode(struct device *dev, bool enable);
 bool dev_pm_genpd_get_hwmode(struct device *dev);
 int dev_pm_genpd_rpm_always_on(struct device *dev, bool on);
+bool dev_pm_genpd_is_on(struct device *dev);
 
 extern struct dev_power_governor simple_qos_governor;
 extern struct dev_power_governor pm_domain_always_on_gov;
@@ -393,6 +394,11 @@ static inline int dev_pm_genpd_rpm_always_on(struct device *dev, bool on)
 	return -EOPNOTSUPP;
 }
 
+static inline bool dev_pm_genpd_is_on(struct device *dev)
+{
+	return false;
+}
+
 #define simple_qos_governor		(*(struct dev_power_governor *)(NULL))
 #define pm_domain_always_on_gov		(*(struct dev_power_governor *)(NULL))
 #endif
Signature · 1 line
2.39.5
#2 lore raw

PATCH v7 2/3 remoteproc: imx_rproc: skip clock enable when M-core is managed by the SCU

In reply to Hiago De Franco

From: Hiago De Franco <[email protected]>

For the i.MX8X and i.MX8 family SoCs, when the Cortex-M core is powered up and started by the Cortex-A core using the bootloader (e.g., via the U-Boot bootaux command), both M-core and Linux run within the same SCFW (System Controller Firmware) partition. With that, Linux has permission to control the M-core.

But once the M-core is started by the bootloader, the SCFW automatically enables its clock and sets the clock rate. If Linux later attempts to enable the same clock via clk_prepare_enable(), the SCFW returns a 'LOCKED' error, as the clock is already configured by the SCFW. This causes the probe function in imx_rproc.c to fail, leading to the M-core power domain being shut down while the core is still running. This results in a fault from the SCU (System Controller Unit) and triggers a system reset.

To address this issue, ignore handling the clk for i.MX8X and i.MX8 M-core, as SCFW already takes care of enabling and configuring the clock.

---
v6 -> v7:
- Added Peng reviewed-by.
v5 -> v6:
- Commit description improved, as suggested.
v4 -> v5:
- Unchanged.
v3 -> v4:
- Unchanged.
v2 -> v3:
- Unchanged.
v1 -> v2:
- Commit description updated, as suggested. Fixed Peng Fan email.

---
 drivers/remoteproc/imx_rproc.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/remoteproc/imx_rproc.c +2 -2
index 74299af1d7f1..627e57a88db2 100644
@@ -1029,8 +1029,8 @@ static int imx_rproc_clk_enable(struct imx_rproc *priv)
 	struct device *dev = priv->dev;
 	int ret;
 
-	/* Remote core is not under control of Linux */
-	if (dcfg->method == IMX_RPROC_NONE)
+	/* Remote core is not under control of Linux or it is managed by SCU API */
+	if (dcfg->method == IMX_RPROC_NONE || dcfg->method == IMX_RPROC_SCU_API)
 		return 0;
 
 	priv->clk = devm_clk_get(dev, NULL);
Signature · 1 line
2.39.5
#3 lore raw

PATCH v7 3/3 remoteproc: imx_rproc: detect and attach to pre-booted remote cores

In reply to Hiago De Franco

From: Hiago De Franco <[email protected]>

When the Cortex-M remote core is started and already running before Linux boots (typically by the Cortex-A bootloader using a command like bootaux), the current driver is unable to attach to it. This is because the driver only checks for remote cores running in different SCFW partitions. However in this case, the M-core is in the same partition as Linux and is already powered up and running by the bootloader.

This patch adds a check using dev_pm_genpd_is_on() to verify whether the M-core's power domains are already on. If all power domain devices are on, the driver assumes the M-core is running and proceed to attach to it.

To accomplish this, we need to avoid passing any attach_data or flags to dev_pm_domain_attach_list(), allowing the platform device become a consumer of the power domain provider without changing its current state.

During probe, also enable and sync the device runtime PM to make sure the power domains are correctly managed when the core is controlled by the kernel.

---
v6 -> v7:
- Added Peng reviewed-by.
v5 -> v6:
- Commit description improved, as suggested. Added Ulf Hansson reviewed by. Comment on imx-rproc.c improved.
v4 -> v5:
- pm_runtime_get_sync() removed in favor of pm_runtime_resume_and_get(). Now it also checks the return value of this function.
- Added pm_runtime_disable() and pm_runtime_put() to imx_rproc_remove() function.
v3 -> v4:
- Changed to use the new dev_pm_genpd_is_on() function instead, as suggested by Ulf. This will now get the power status of the two remote cores power domains to decided if imx_rpoc needs to attach or not. In order to do that, pm_runtime_enable() and pm_runtime_get_sync() were introduced and pd_data was removed.
v2 -> v3:
- Unchanged.
v1 -> v2:
- Dropped unecessary include. Removed the imx_rproc_is_on function, as suggested.

---
 drivers/remoteproc/imx_rproc.c | 37 +++++++++++++++++++++++++++++-----
 1 file changed, 32 insertions(+), 5 deletions(-)
drivers/remoteproc/imx_rproc.c +32 -5
index 627e57a88db2..24597b60c5b0 100644
@@ -18,6 +18,7 @@
 #include <linux/of_reserved_mem.h>
 #include <linux/platform_device.h>
 #include <linux/pm_domain.h>
+#include <linux/pm_runtime.h>
 #include <linux/reboot.h>
 #include <linux/regmap.h>
 #include <linux/remoteproc.h>
@@ -890,10 +891,8 @@ static int imx_rproc_partition_notify(struct notifier_block *nb,
 static int imx_rproc_attach_pd(struct imx_rproc *priv)
 {
 	struct device *dev = priv->dev;
-	int ret;
-	struct dev_pm_domain_attach_data pd_data = {
-		.pd_flags = PD_FLAG_DEV_LINK_ON,
-	};
+	int ret, i;
+	bool detached = true;
 
 	/*
 	 * If there is only one power-domain entry, the platform driver framework
@@ -902,7 +901,22 @@ static int imx_rproc_attach_pd(struct imx_rproc *priv)
 	if (dev->pm_domain)
 		return 0;
 
-	ret = dev_pm_domain_attach_list(dev, &pd_data, &priv->pd_list);
+	ret = dev_pm_domain_attach_list(dev, NULL, &priv->pd_list);
+	/*
+	 * If all the power domain devices are already turned on, the remote
+	 * core is already powered up and running when the kernel booted (e.g.,
+	 * started by U-Boot's bootaux command). In this case attach to it.
+	 */
+	for (i = 0; i < ret; i++) {
+		if (!dev_pm_genpd_is_on(priv->pd_list->pd_devs[i])) {
+			detached = false;
+			break;
+		}
+	}
+
+	if (detached)
+		priv->rproc->state = RPROC_DETACHED;
+
 	return ret < 0 ? ret : 0;
 }
 
@@ -1146,6 +1160,15 @@ static int imx_rproc_probe(struct platform_device *pdev)
 		}
 	}
 
+	if (dcfg->method == IMX_RPROC_SCU_API) {
+		pm_runtime_enable(dev);
+		ret = pm_runtime_resume_and_get(dev);
+		if (ret) {
+			dev_err(dev, "pm_runtime get failed: %d\n", ret);
+			goto err_put_clk;
+		}
+	}
+
 	ret = rproc_add(rproc);
 	if (ret) {
 		dev_err(dev, "rproc_add failed\n");
@@ -1171,6 +1194,10 @@ static void imx_rproc_remove(struct platform_device *pdev)
 	struct rproc *rproc = platform_get_drvdata(pdev);
 	struct imx_rproc *priv = rproc->priv;
 
+	if (priv->dcfg->method == IMX_RPROC_SCU_API) {
+		pm_runtime_disable(priv->dev);
+		pm_runtime_put(priv->dev);
+	}
 	clk_disable_unprepare(priv->clk);
 	rproc_del(rproc);
 	imx_rproc_put_scu(rproc);
Signature · 1 line
2.39.5
maintainer
#4 lore raw

Re: [PATCH v7 3/3] remoteproc: imx_rproc: detect and attach to pre-booted remote cores

Quoted 86 lines · Hiago De Franco

From: Hiago De Franco <[email protected]>

When the Cortex-M remote core is started and already running before Linux boots (typically by the Cortex-A bootloader using a command like bootaux), the current driver is unable to attach to it. This is because the driver only checks for remote cores running in different SCFW partitions. However in this case, the M-core is in the same partition as Linux and is already powered up and running by the bootloader.

This patch adds a check using dev_pm_genpd_is_on() to verify whether the M-core's power domains are already on. If all power domain devices are on, the driver assumes the M-core is running and proceed to attach to it.

To accomplish this, we need to avoid passing any attach_data or flags to dev_pm_domain_attach_list(), allowing the platform device become a consumer of the power domain provider without changing its current state.

During probe, also enable and sync the device runtime PM to make sure the power domains are correctly managed when the core is controlled by the kernel.

---
v6 -> v7:
- Added Peng reviewed-by.
v5 -> v6:
- Commit description improved, as suggested. Added Ulf Hansson reviewed by. Comment on imx-rproc.c improved.
v4 -> v5:
- pm_runtime_get_sync() removed in favor of pm_runtime_resume_and_get(). Now it also checks the return value of this function.
- Added pm_runtime_disable() and pm_runtime_put() to imx_rproc_remove() function.
v3 -> v4:
- Changed to use the new dev_pm_genpd_is_on() function instead, as suggested by Ulf. This will now get the power status of the two remote cores power domains to decided if imx_rpoc needs to attach or not. In order to do that, pm_runtime_enable() and pm_runtime_get_sync() were introduced and pd_data was removed.
v2 -> v3:
- Unchanged.
v1 -> v2:
- Dropped unecessary include. Removed the imx_rproc_is_on function, as suggested.

---
 drivers/remoteproc/imx_rproc.c | 37 +++++++++++++++++++++++++++++-----
 1 file changed, 32 insertions(+), 5 deletions(-)
drivers/remoteproc/imx_rproc.c +5 -5
index 627e57a88db2..24597b60c5b0 100644
@@ -18,6 +18,7 @@
 #include <linux/of_reserved_mem.h>
 #include <linux/platform_device.h>
 #include <linux/pm_domain.h>
+#include <linux/pm_runtime.h>
 #include <linux/reboot.h>
 #include <linux/regmap.h>
 #include <linux/remoteproc.h>
@@ -890,10 +891,8 @@ static int imx_rproc_partition_notify(struct notifier_block *nb,
 static int imx_rproc_attach_pd(struct imx_rproc *priv)
 {
 	struct device *dev = priv->dev;
-	int ret;
-	struct dev_pm_domain_attach_data pd_data = {
-		.pd_flags = PD_FLAG_DEV_LINK_ON,
-	};
+	int ret, i;
+	bool detached = true;
 
 	/*
 	 * If there is only one power-domain entry, the platform driver framework
@@ -902,7 +901,22 @@ static int imx_rproc_attach_pd(struct imx_rproc *priv)
 	if (dev->pm_domain)
 		return 0;
 
-	ret = dev_pm_domain_attach_list(dev, &pd_data, &priv->pd_list);
+	ret = dev_pm_domain_attach_list(dev, NULL, &priv->pd_list);
+	/*

drivers/remoteproc/imx_rproc.c static int imx_rproc_attach_pd(struct imx_rproc *priv) · line 915

Quoted 10 lines
drivers/remoteproc/imx_rproc.c +10 -0
+	 * If all the power domain devices are already turned on, the remote
+	 * core is already powered up and running when the kernel booted (e.g.,
+	 * started by U-Boot's bootaux command). In this case attach to it.
+	 */
+	for (i = 0; i < ret; i++) {
+		if (!dev_pm_genpd_is_on(priv->pd_list->pd_devs[i])) {
+			detached = false;
+			break;
+		}
+	}

I was doing one final review of this work when I noticed the return code for dev_pm_domain_attach_list() is never checked for error.

Thanks,
Mathieu

Quoted 37 lines
drivers/remoteproc/imx_rproc.c +17 -0
+
+	if (detached)
+		priv->rproc->state = RPROC_DETACHED;
+
 	return ret < 0 ? ret : 0;
 }
 
@@ -1146,6 +1160,15 @@ static int imx_rproc_probe(struct platform_device *pdev)
 		}
 	}
 
+	if (dcfg->method == IMX_RPROC_SCU_API) {
+		pm_runtime_enable(dev);
+		ret = pm_runtime_resume_and_get(dev);
+		if (ret) {
+			dev_err(dev, "pm_runtime get failed: %d\n", ret);
+			goto err_put_clk;
+		}
+	}
+
 	ret = rproc_add(rproc);
 	if (ret) {
 		dev_err(dev, "rproc_add failed\n");
@@ -1171,6 +1194,10 @@ static void imx_rproc_remove(struct platform_device *pdev)
 	struct rproc *rproc = platform_get_drvdata(pdev);
 	struct imx_rproc *priv = rproc->priv;
 
+	if (priv->dcfg->method == IMX_RPROC_SCU_API) {
+		pm_runtime_disable(priv->dev);
+		pm_runtime_put(priv->dev);
+	}
 	clk_disable_unprepare(priv->clk);
 	rproc_del(rproc);
 	imx_rproc_put_scu(rproc);
Signature · 1 line
2.39.5
#5 lore raw

Re: [PATCH v7 3/3] remoteproc: imx_rproc: detect and attach to pre-booted remote cores

Quoted 85 lines · Mathieu Poirier
Quoted 83 lines · Hiago De Franco

From: Hiago De Franco <[email protected]>

When the Cortex-M remote core is started and already running before Linux boots (typically by the Cortex-A bootloader using a command like bootaux), the current driver is unable to attach to it. This is because the driver only checks for remote cores running in different SCFW partitions. However in this case, the M-core is in the same partition as Linux and is already powered up and running by the bootloader.

This patch adds a check using dev_pm_genpd_is_on() to verify whether the M-core's power domains are already on. If all power domain devices are on, the driver assumes the M-core is running and proceed to attach to it.

To accomplish this, we need to avoid passing any attach_data or flags to dev_pm_domain_attach_list(), allowing the platform device become a consumer of the power domain provider without changing its current state.

During probe, also enable and sync the device runtime PM to make sure the power domains are correctly managed when the core is controlled by the kernel.

---
v6 -> v7:
- Added Peng reviewed-by.
v5 -> v6:
- Commit description improved, as suggested. Added Ulf Hansson reviewed by. Comment on imx-rproc.c improved.
v4 -> v5:
- pm_runtime_get_sync() removed in favor of pm_runtime_resume_and_get(). Now it also checks the return value of this function.
- Added pm_runtime_disable() and pm_runtime_put() to imx_rproc_remove() function.
v3 -> v4:
- Changed to use the new dev_pm_genpd_is_on() function instead, as suggested by Ulf. This will now get the power status of the two remote cores power domains to decided if imx_rpoc needs to attach or not. In order to do that, pm_runtime_enable() and pm_runtime_get_sync() were introduced and pd_data was removed.
v2 -> v3:
- Unchanged.
v1 -> v2:
- Dropped unecessary include. Removed the imx_rproc_is_on function, as suggested.

---
 drivers/remoteproc/imx_rproc.c | 37 +++++++++++++++++++++++++++++-----
 1 file changed, 32 insertions(+), 5 deletions(-)
drivers/remoteproc/imx_rproc.c +3 -4
index 627e57a88db2..24597b60c5b0 100644
@@ -18,6 +18,7 @@
 #include <linux/of_reserved_mem.h>
 #include <linux/platform_device.h>
 #include <linux/pm_domain.h>
+#include <linux/pm_runtime.h>
 #include <linux/reboot.h>
 #include <linux/regmap.h>
 #include <linux/remoteproc.h>
@@ -890,10 +891,8 @@ static int imx_rproc_partition_notify(struct notifier_block *nb,
 static int imx_rproc_attach_pd(struct imx_rproc *priv)
 {
      struct device *dev = priv->dev;
-     int ret;
-     struct dev_pm_domain_attach_data pd_data = {
-             .pd_flags = PD_FLAG_DEV_LINK_ON,
-     };
+     int ret, i;
+     bool detached = true;
 
      /*
       * If there is only one power-domain entry, the platform driver framework
@@ -902,7 +901,22 @@ static int imx_rproc_attach_pd(struct imx_rproc *priv)
      if (dev->pm_domain)
              return 0;
 
Quoted 16 lines

drivers/remoteproc/imx_rproc.c static int imx_rproc_attach_pd(struct imx_rproc *priv) · line 915

Quoted 13 lines
drivers/remoteproc/imx_rproc.c +12 -1
-     ret = dev_pm_domain_attach_list(dev, &pd_data, &priv->pd_list);
+     ret = dev_pm_domain_attach_list(dev, NULL, &priv->pd_list);
+     /*
+      * If all the power domain devices are already turned on, the remote
+      * core is already powered up and running when the kernel booted (e.g.,
+      * started by U-Boot's bootaux command). In this case attach to it.
+      */
+     for (i = 0; i < ret; i++) {
+             if (!dev_pm_genpd_is_on(priv->pd_list->pd_devs[i])) {
+                     detached = false;
+                     break;
+             }
+     }

I was doing one final review of this work when I noticed the return code for dev_pm_domain_attach_list() is never checked for error.

The for loop covers the error condition correctly, I think. It's only when ret >=1 when the loop should be started - and ret is propagated to the caller a few lines below.

Quoted 4 lines

Thanks,
Mathieu

Kind regards
Uffe

Quoted 37 lines
Quoted 37 lines
drivers/remoteproc/imx_rproc.c +17 -1
+
+     if (detached)
+             priv->rproc->state = RPROC_DETACHED;
+
      return ret < 0 ? ret : 0;
 }
 
@@ -1146,6 +1160,15 @@ static int imx_rproc_probe(struct platform_device *pdev)
              }
      }
 
+     if (dcfg->method == IMX_RPROC_SCU_API) {
+             pm_runtime_enable(dev);
+             ret = pm_runtime_resume_and_get(dev);
+             if (ret) {
+                     dev_err(dev, "pm_runtime get failed: %d\n", ret);
+                     goto err_put_clk;
+             }
+     }
+
      ret = rproc_add(rproc);
      if (ret) {
              dev_err(dev, "rproc_add failed\n");
@@ -1171,6 +1194,10 @@ static void imx_rproc_remove(struct platform_device *pdev)
      struct rproc *rproc = platform_get_drvdata(pdev);
      struct imx_rproc *priv = rproc->priv;
 
+     if (priv->dcfg->method == IMX_RPROC_SCU_API) {
+             pm_runtime_disable(priv->dev);
+             pm_runtime_put(priv->dev);
+     }
      clk_disable_unprepare(priv->clk);
      rproc_del(rproc);
      imx_rproc_put_scu(rproc);
--

2.39.5

#6 lore raw

Re: [PATCH v7 3/3] remoteproc: imx_rproc: detect and attach to pre-booted remote cores

In reply to Mathieu Poirier

Hi Mathieu, Ulf,

Quoted 84 lines · Mathieu Poirier
Quoted 83 lines · Hiago De Franco

From: Hiago De Franco <[email protected]>

When the Cortex-M remote core is started and already running before Linux boots (typically by the Cortex-A bootloader using a command like bootaux), the current driver is unable to attach to it. This is because the driver only checks for remote cores running in different SCFW partitions. However in this case, the M-core is in the same partition as Linux and is already powered up and running by the bootloader.

This patch adds a check using dev_pm_genpd_is_on() to verify whether the M-core's power domains are already on. If all power domain devices are on, the driver assumes the M-core is running and proceed to attach to it.

To accomplish this, we need to avoid passing any attach_data or flags to dev_pm_domain_attach_list(), allowing the platform device become a consumer of the power domain provider without changing its current state.

During probe, also enable and sync the device runtime PM to make sure the power domains are correctly managed when the core is controlled by the kernel.

---
v6 -> v7:
- Added Peng reviewed-by.
v5 -> v6:
- Commit description improved, as suggested. Added Ulf Hansson reviewed by. Comment on imx-rproc.c improved.
v4 -> v5:
- pm_runtime_get_sync() removed in favor of pm_runtime_resume_and_get(). Now it also checks the return value of this function.
- Added pm_runtime_disable() and pm_runtime_put() to imx_rproc_remove() function.
v3 -> v4:
- Changed to use the new dev_pm_genpd_is_on() function instead, as suggested by Ulf. This will now get the power status of the two remote cores power domains to decided if imx_rpoc needs to attach or not. In order to do that, pm_runtime_enable() and pm_runtime_get_sync() were introduced and pd_data was removed.
v2 -> v3:
- Unchanged.
v1 -> v2:
- Dropped unecessary include. Removed the imx_rproc_is_on function, as suggested.

---
 drivers/remoteproc/imx_rproc.c | 37 +++++++++++++++++++++++++++++-----
 1 file changed, 32 insertions(+), 5 deletions(-)
drivers/remoteproc/imx_rproc.c +3 -4
index 627e57a88db2..24597b60c5b0 100644
@@ -18,6 +18,7 @@
 #include <linux/of_reserved_mem.h>
 #include <linux/platform_device.h>
 #include <linux/pm_domain.h>
+#include <linux/pm_runtime.h>
 #include <linux/reboot.h>
 #include <linux/regmap.h>
 #include <linux/remoteproc.h>
@@ -890,10 +891,8 @@ static int imx_rproc_partition_notify(struct notifier_block *nb,
 static int imx_rproc_attach_pd(struct imx_rproc *priv)
 {
 	struct device *dev = priv->dev;
-	int ret;
-	struct dev_pm_domain_attach_data pd_data = {
-		.pd_flags = PD_FLAG_DEV_LINK_ON,
-	};
+	int ret, i;
+	bool detached = true;
 
 	/*
 	 * If there is only one power-domain entry, the platform driver framework
@@ -902,7 +901,22 @@ static int imx_rproc_attach_pd(struct imx_rproc *priv)
 	if (dev->pm_domain)
 		return 0;
 
Quoted 16 lines

drivers/remoteproc/imx_rproc.c static int imx_rproc_attach_pd(struct imx_rproc *priv) · line 915

Quoted 13 lines
drivers/remoteproc/imx_rproc.c +12 -1
-	ret = dev_pm_domain_attach_list(dev, &pd_data, &priv->pd_list);
+	ret = dev_pm_domain_attach_list(dev, NULL, &priv->pd_list);
+	/*
+	 * If all the power domain devices are already turned on, the remote
+	 * core is already powered up and running when the kernel booted (e.g.,
+	 * started by U-Boot's bootaux command). In this case attach to it.
+	 */
+	for (i = 0; i < ret; i++) {
+		if (!dev_pm_genpd_is_on(priv->pd_list->pd_devs[i])) {
+			detached = false;
+			break;
+		}
+	}

I was doing one final review of this work when I noticed the return code for dev_pm_domain_attach_list() is never checked for error.

As Ulf pointed out, the 'return' a few lines below will return the negative value to the caller of 'imx_rproc_attach_pd', which ultimately will fail 'imx_rproc_detect_mode' and fail the probe of imx_rproc.

Please notice that even tough 'dev_pm_domain_attach_list' fails, the rproc->state will still be set as RPROC_DETACHED because we are starting 'detached' as true, but I am not seeing this as an issue because as mentioned above the probe will fail anyway. Please let me know if you see this as an issue.

Quoted 41 lines

Thanks,
Mathieu

Quoted 37 lines
drivers/remoteproc/imx_rproc.c +17 -0
+
+	if (detached)
+		priv->rproc->state = RPROC_DETACHED;
+
 	return ret < 0 ? ret : 0;
 }
 
@@ -1146,6 +1160,15 @@ static int imx_rproc_probe(struct platform_device *pdev)
 		}
 	}
 
+	if (dcfg->method == IMX_RPROC_SCU_API) {
+		pm_runtime_enable(dev);
+		ret = pm_runtime_resume_and_get(dev);
+		if (ret) {
+			dev_err(dev, "pm_runtime get failed: %d\n", ret);
+			goto err_put_clk;
+		}
+	}
+
 	ret = rproc_add(rproc);
 	if (ret) {
 		dev_err(dev, "rproc_add failed\n");
@@ -1171,6 +1194,10 @@ static void imx_rproc_remove(struct platform_device *pdev)
 	struct rproc *rproc = platform_get_drvdata(pdev);
 	struct imx_rproc *priv = rproc->priv;
 
+	if (priv->dcfg->method == IMX_RPROC_SCU_API) {
+		pm_runtime_disable(priv->dev);
+		pm_runtime_put(priv->dev);
+	}
 	clk_disable_unprepare(priv->clk);
 	rproc_del(rproc);
 	imx_rproc_put_scu(rproc);
Signature · 1 line
2.39.5
Quoted 143 lines · Ulf Hansson
Quoted 85 lines · Mathieu Poirier
Quoted 83 lines · Hiago De Franco

From: Hiago De Franco <[email protected]>

When the Cortex-M remote core is started and already running before Linux boots (typically by the Cortex-A bootloader using a command like bootaux), the current driver is unable to attach to it. This is because the driver only checks for remote cores running in different SCFW partitions. However in this case, the M-core is in the same partition as Linux and is already powered up and running by the bootloader.

This patch adds a check using dev_pm_genpd_is_on() to verify whether the M-core's power domains are already on. If all power domain devices are on, the driver assumes the M-core is running and proceed to attach to it.

To accomplish this, we need to avoid passing any attach_data or flags to dev_pm_domain_attach_list(), allowing the platform device become a consumer of the power domain provider without changing its current state.

During probe, also enable and sync the device runtime PM to make sure the power domains are correctly managed when the core is controlled by the kernel.

---
v6 -> v7:
- Added Peng reviewed-by.
v5 -> v6:
- Commit description improved, as suggested. Added Ulf Hansson reviewed by. Comment on imx-rproc.c improved.
v4 -> v5:
- pm_runtime_get_sync() removed in favor of pm_runtime_resume_and_get(). Now it also checks the return value of this function.
- Added pm_runtime_disable() and pm_runtime_put() to imx_rproc_remove() function.
v3 -> v4:
- Changed to use the new dev_pm_genpd_is_on() function instead, as suggested by Ulf. This will now get the power status of the two remote cores power domains to decided if imx_rpoc needs to attach or not. In order to do that, pm_runtime_enable() and pm_runtime_get_sync() were introduced and pd_data was removed.
v2 -> v3:
- Unchanged.
v1 -> v2:
- Dropped unecessary include. Removed the imx_rproc_is_on function, as suggested.

---
 drivers/remoteproc/imx_rproc.c | 37 +++++++++++++++++++++++++++++-----
 1 file changed, 32 insertions(+), 5 deletions(-)
drivers/remoteproc/imx_rproc.c +3 -4
index 627e57a88db2..24597b60c5b0 100644
@@ -18,6 +18,7 @@
 #include <linux/of_reserved_mem.h>
 #include <linux/platform_device.h>
 #include <linux/pm_domain.h>
+#include <linux/pm_runtime.h>
 #include <linux/reboot.h>
 #include <linux/regmap.h>
 #include <linux/remoteproc.h>
@@ -890,10 +891,8 @@ static int imx_rproc_partition_notify(struct notifier_block *nb,
 static int imx_rproc_attach_pd(struct imx_rproc *priv)
 {
      struct device *dev = priv->dev;
-     int ret;
-     struct dev_pm_domain_attach_data pd_data = {
-             .pd_flags = PD_FLAG_DEV_LINK_ON,
-     };
+     int ret, i;
+     bool detached = true;
 
      /*
       * If there is only one power-domain entry, the platform driver framework
@@ -902,7 +901,22 @@ static int imx_rproc_attach_pd(struct imx_rproc *priv)
      if (dev->pm_domain)
              return 0;
 
Quoted 16 lines

drivers/remoteproc/imx_rproc.c static int imx_rproc_attach_pd(struct imx_rproc *priv) · line 915

Quoted 13 lines
drivers/remoteproc/imx_rproc.c +12 -1
-     ret = dev_pm_domain_attach_list(dev, &pd_data, &priv->pd_list);
+     ret = dev_pm_domain_attach_list(dev, NULL, &priv->pd_list);
+     /*
+      * If all the power domain devices are already turned on, the remote
+      * core is already powered up and running when the kernel booted (e.g.,
+      * started by U-Boot's bootaux command). In this case attach to it.
+      */
+     for (i = 0; i < ret; i++) {
+             if (!dev_pm_genpd_is_on(priv->pd_list->pd_devs[i])) {
+                     detached = false;
+                     break;
+             }
+     }

I was doing one final review of this work when I noticed the return code for dev_pm_domain_attach_list() is never checked for error.

The for loop covers the error condition correctly, I think. It's only when ret >=1 when the loop should be started - and ret is propagated to the caller a few lines below.

Quoted 4 lines

Thanks,
Mathieu

Kind regards
Uffe

Quoted 27 lines
Quoted 27 lines
drivers/remoteproc/imx_rproc.c +13 -0
+
+     if (detached)
+             priv->rproc->state = RPROC_DETACHED;
+
      return ret < 0 ? ret : 0;
 }
 
@@ -1146,6 +1160,15 @@ static int imx_rproc_probe(struct platform_device *pdev)
              }
      }
 
+     if (dcfg->method == IMX_RPROC_SCU_API) {
+             pm_runtime_enable(dev);
+             ret = pm_runtime_resume_and_get(dev);
+             if (ret) {
+                     dev_err(dev, "pm_runtime get failed: %d\n", ret);
+                     goto err_put_clk;
+             }
+     }
+
      ret = rproc_add(rproc);
      if (ret) {
              dev_err(dev, "rproc_add failed\n");
@@ -1171,6 +1194,10 @@ static void imx_rproc_remove(struct platform_device *pdev)
      struct rproc *rproc = platform_get_drvdata(pdev);
      struct imx_rproc *priv = rproc->priv;
 
Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
drivers/remoteproc/imx_rproc.c +4 -1
+     if (priv->dcfg->method == IMX_RPROC_SCU_API) {
+             pm_runtime_disable(priv->dev);
+             pm_runtime_put(priv->dev);
+     }
      clk_disable_unprepare(priv->clk);
      rproc_del(rproc);
      imx_rproc_put_scu(rproc);
--

2.39.5

Best Regards,

Hiago.

maintainer
#7 lore raw

Re: [PATCH v7 3/3] remoteproc: imx_rproc: detect and attach to pre-booted remote cores

Quoted 108 lines · Hiago De Franco

Hi Mathieu, Ulf,

Quoted 84 lines · Mathieu Poirier
Quoted 83 lines · Hiago De Franco

From: Hiago De Franco <[email protected]>

When the Cortex-M remote core is started and already running before Linux boots (typically by the Cortex-A bootloader using a command like bootaux), the current driver is unable to attach to it. This is because the driver only checks for remote cores running in different SCFW partitions. However in this case, the M-core is in the same partition as Linux and is already powered up and running by the bootloader.

This patch adds a check using dev_pm_genpd_is_on() to verify whether the M-core's power domains are already on. If all power domain devices are on, the driver assumes the M-core is running and proceed to attach to it.

To accomplish this, we need to avoid passing any attach_data or flags to dev_pm_domain_attach_list(), allowing the platform device become a consumer of the power domain provider without changing its current state.

During probe, also enable and sync the device runtime PM to make sure the power domains are correctly managed when the core is controlled by the kernel.

---
v6 -> v7:
- Added Peng reviewed-by.
v5 -> v6:
- Commit description improved, as suggested. Added Ulf Hansson reviewed by. Comment on imx-rproc.c improved.
v4 -> v5:
- pm_runtime_get_sync() removed in favor of pm_runtime_resume_and_get(). Now it also checks the return value of this function.
- Added pm_runtime_disable() and pm_runtime_put() to imx_rproc_remove() function.
v3 -> v4:
- Changed to use the new dev_pm_genpd_is_on() function instead, as suggested by Ulf. This will now get the power status of the two remote cores power domains to decided if imx_rpoc needs to attach or not. In order to do that, pm_runtime_enable() and pm_runtime_get_sync() were introduced and pd_data was removed.
v2 -> v3:
- Unchanged.
v1 -> v2:
- Dropped unecessary include. Removed the imx_rproc_is_on function, as suggested.

---
 drivers/remoteproc/imx_rproc.c | 37 +++++++++++++++++++++++++++++-----
 1 file changed, 32 insertions(+), 5 deletions(-)
drivers/remoteproc/imx_rproc.c +3 -4
index 627e57a88db2..24597b60c5b0 100644
@@ -18,6 +18,7 @@
 #include <linux/of_reserved_mem.h>
 #include <linux/platform_device.h>
 #include <linux/pm_domain.h>
+#include <linux/pm_runtime.h>
 #include <linux/reboot.h>
 #include <linux/regmap.h>
 #include <linux/remoteproc.h>
@@ -890,10 +891,8 @@ static int imx_rproc_partition_notify(struct notifier_block *nb,
 static int imx_rproc_attach_pd(struct imx_rproc *priv)
 {
 	struct device *dev = priv->dev;
-	int ret;
-	struct dev_pm_domain_attach_data pd_data = {
-		.pd_flags = PD_FLAG_DEV_LINK_ON,
-	};
+	int ret, i;
+	bool detached = true;
 
 	/*
 	 * If there is only one power-domain entry, the platform driver framework
@@ -902,7 +901,22 @@ static int imx_rproc_attach_pd(struct imx_rproc *priv)
 	if (dev->pm_domain)
 		return 0;
 
Quoted 16 lines

drivers/remoteproc/imx_rproc.c static int imx_rproc_attach_pd(struct imx_rproc *priv) · line 915

Quoted 13 lines
drivers/remoteproc/imx_rproc.c +12 -1
-	ret = dev_pm_domain_attach_list(dev, &pd_data, &priv->pd_list);
+	ret = dev_pm_domain_attach_list(dev, NULL, &priv->pd_list);
+	/*
+	 * If all the power domain devices are already turned on, the remote
+	 * core is already powered up and running when the kernel booted (e.g.,
+	 * started by U-Boot's bootaux command). In this case attach to it.
+	 */
+	for (i = 0; i < ret; i++) {
+		if (!dev_pm_genpd_is_on(priv->pd_list->pd_devs[i])) {
+			detached = false;
+			break;
+		}
+	}

I was doing one final review of this work when I noticed the return code for dev_pm_domain_attach_list() is never checked for error.

As Ulf pointed out, the 'return' a few lines below will return the negative value to the caller of 'imx_rproc_attach_pd', which ultimately will fail 'imx_rproc_detect_mode' and fail the probe of imx_rproc.

Quoted 5 lines

Please notice that even tough 'dev_pm_domain_attach_list' fails, the rproc->state will still be set as RPROC_DETACHED because we are starting 'detached' as true, but I am not seeing this as an issue because as mentioned above the probe will fail anyway. Please let me know if you see this as an issue.

Two things to consider here:

(1) It is only a matter of time before someone with a cleaver coccinelle script sends me a patch that adds the missing error check.

(2) I think that @rproc->state being changed on error conditions is a bug waiting to happen. This kind of implicit error handling is difficult to maintain and even more difficult for people to make enhancements to the driver.

Adding a simple error check will make sure neither of the above will happen. It is a simple change and we are at rc6 - this work can still go in the merge window.

Quoted 201 lines
Quoted 42 lines

Thanks,
Mathieu

Quoted 37 lines
drivers/remoteproc/imx_rproc.c +17 -0
+
+	if (detached)
+		priv->rproc->state = RPROC_DETACHED;
+
 	return ret < 0 ? ret : 0;
 }
 
@@ -1146,6 +1160,15 @@ static int imx_rproc_probe(struct platform_device *pdev)
 		}
 	}
 
+	if (dcfg->method == IMX_RPROC_SCU_API) {
+		pm_runtime_enable(dev);
+		ret = pm_runtime_resume_and_get(dev);
+		if (ret) {
+			dev_err(dev, "pm_runtime get failed: %d\n", ret);
+			goto err_put_clk;
+		}
+	}
+
 	ret = rproc_add(rproc);
 	if (ret) {
 		dev_err(dev, "rproc_add failed\n");
@@ -1171,6 +1194,10 @@ static void imx_rproc_remove(struct platform_device *pdev)
 	struct rproc *rproc = platform_get_drvdata(pdev);
 	struct imx_rproc *priv = rproc->priv;
 
+	if (priv->dcfg->method == IMX_RPROC_SCU_API) {
+		pm_runtime_disable(priv->dev);
+		pm_runtime_put(priv->dev);
+	}
 	clk_disable_unprepare(priv->clk);
 	rproc_del(rproc);
 	imx_rproc_put_scu(rproc);
Signature · 1 line
2.39.5
Quoted 143 lines · Ulf Hansson
Quoted 85 lines · Mathieu Poirier
Quoted 83 lines · Hiago De Franco

From: Hiago De Franco <[email protected]>

When the Cortex-M remote core is started and already running before Linux boots (typically by the Cortex-A bootloader using a command like bootaux), the current driver is unable to attach to it. This is because the driver only checks for remote cores running in different SCFW partitions. However in this case, the M-core is in the same partition as Linux and is already powered up and running by the bootloader.

This patch adds a check using dev_pm_genpd_is_on() to verify whether the M-core's power domains are already on. If all power domain devices are on, the driver assumes the M-core is running and proceed to attach to it.

To accomplish this, we need to avoid passing any attach_data or flags to dev_pm_domain_attach_list(), allowing the platform device become a consumer of the power domain provider without changing its current state.

During probe, also enable and sync the device runtime PM to make sure the power domains are correctly managed when the core is controlled by the kernel.

---
v6 -> v7:
- Added Peng reviewed-by.
v5 -> v6:
- Commit description improved, as suggested. Added Ulf Hansson reviewed by. Comment on imx-rproc.c improved.
v4 -> v5:
- pm_runtime_get_sync() removed in favor of pm_runtime_resume_and_get(). Now it also checks the return value of this function.
- Added pm_runtime_disable() and pm_runtime_put() to imx_rproc_remove() function.
v3 -> v4:
- Changed to use the new dev_pm_genpd_is_on() function instead, as suggested by Ulf. This will now get the power status of the two remote cores power domains to decided if imx_rpoc needs to attach or not. In order to do that, pm_runtime_enable() and pm_runtime_get_sync() were introduced and pd_data was removed.
v2 -> v3:
- Unchanged.
v1 -> v2:
- Dropped unecessary include. Removed the imx_rproc_is_on function, as suggested.

---
 drivers/remoteproc/imx_rproc.c | 37 +++++++++++++++++++++++++++++-----
 1 file changed, 32 insertions(+), 5 deletions(-)
drivers/remoteproc/imx_rproc.c +3 -4
index 627e57a88db2..24597b60c5b0 100644
@@ -18,6 +18,7 @@
 #include <linux/of_reserved_mem.h>
 #include <linux/platform_device.h>
 #include <linux/pm_domain.h>
+#include <linux/pm_runtime.h>
 #include <linux/reboot.h>
 #include <linux/regmap.h>
 #include <linux/remoteproc.h>
@@ -890,10 +891,8 @@ static int imx_rproc_partition_notify(struct notifier_block *nb,
 static int imx_rproc_attach_pd(struct imx_rproc *priv)
 {
      struct device *dev = priv->dev;
-     int ret;
-     struct dev_pm_domain_attach_data pd_data = {
-             .pd_flags = PD_FLAG_DEV_LINK_ON,
-     };
+     int ret, i;
+     bool detached = true;
 
      /*
       * If there is only one power-domain entry, the platform driver framework
@@ -902,7 +901,22 @@ static int imx_rproc_attach_pd(struct imx_rproc *priv)
      if (dev->pm_domain)
              return 0;
 
Quoted 16 lines

drivers/remoteproc/imx_rproc.c static int imx_rproc_attach_pd(struct imx_rproc *priv) · line 915

Quoted 13 lines
drivers/remoteproc/imx_rproc.c +12 -1
-     ret = dev_pm_domain_attach_list(dev, &pd_data, &priv->pd_list);
+     ret = dev_pm_domain_attach_list(dev, NULL, &priv->pd_list);
+     /*
+      * If all the power domain devices are already turned on, the remote
+      * core is already powered up and running when the kernel booted (e.g.,
+      * started by U-Boot's bootaux command). In this case attach to it.
+      */
+     for (i = 0; i < ret; i++) {
+             if (!dev_pm_genpd_is_on(priv->pd_list->pd_devs[i])) {
+                     detached = false;
+                     break;
+             }
+     }

I was doing one final review of this work when I noticed the return code for dev_pm_domain_attach_list() is never checked for error.

The for loop covers the error condition correctly, I think. It's only when ret >=1 when the loop should be started - and ret is propagated to the caller a few lines below.

Quoted 4 lines

Thanks,
Mathieu

Kind regards
Uffe

Quoted 27 lines
Quoted 27 lines
drivers/remoteproc/imx_rproc.c +13 -0
+
+     if (detached)
+             priv->rproc->state = RPROC_DETACHED;
+
      return ret < 0 ? ret : 0;
 }
 
@@ -1146,6 +1160,15 @@ static int imx_rproc_probe(struct platform_device *pdev)
              }
      }
 
+     if (dcfg->method == IMX_RPROC_SCU_API) {
+             pm_runtime_enable(dev);
+             ret = pm_runtime_resume_and_get(dev);
+             if (ret) {
+                     dev_err(dev, "pm_runtime get failed: %d\n", ret);
+                     goto err_put_clk;
+             }
+     }
+
      ret = rproc_add(rproc);
      if (ret) {
              dev_err(dev, "rproc_add failed\n");
@@ -1171,6 +1194,10 @@ static void imx_rproc_remove(struct platform_device *pdev)
      struct rproc *rproc = platform_get_drvdata(pdev);
      struct imx_rproc *priv = rproc->priv;
 
Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
drivers/remoteproc/imx_rproc.c +4 -1
+     if (priv->dcfg->method == IMX_RPROC_SCU_API) {
+             pm_runtime_disable(priv->dev);
+             pm_runtime_put(priv->dev);
+     }
      clk_disable_unprepare(priv->clk);
      rproc_del(rproc);
      imx_rproc_put_scu(rproc);
--

2.39.5

Best Regards,

Hiago.

#8 lore raw

Re: [PATCH v7 3/3] remoteproc: imx_rproc: detect and attach to pre-booted remote cores

Quoted 120 lines · Mathieu Poirier
Quoted 108 lines · Hiago De Franco

Hi Mathieu, Ulf,

Quoted 84 lines · Mathieu Poirier
Quoted 83 lines · Hiago De Franco

From: Hiago De Franco <[email protected]>

When the Cortex-M remote core is started and already running before Linux boots (typically by the Cortex-A bootloader using a command like bootaux), the current driver is unable to attach to it. This is because the driver only checks for remote cores running in different SCFW partitions. However in this case, the M-core is in the same partition as Linux and is already powered up and running by the bootloader.

This patch adds a check using dev_pm_genpd_is_on() to verify whether the M-core's power domains are already on. If all power domain devices are on, the driver assumes the M-core is running and proceed to attach to it.

To accomplish this, we need to avoid passing any attach_data or flags to dev_pm_domain_attach_list(), allowing the platform device become a consumer of the power domain provider without changing its current state.

During probe, also enable and sync the device runtime PM to make sure the power domains are correctly managed when the core is controlled by the kernel.

---
v6 -> v7:
- Added Peng reviewed-by.
v5 -> v6:
- Commit description improved, as suggested. Added Ulf Hansson reviewed by. Comment on imx-rproc.c improved.
v4 -> v5:
- pm_runtime_get_sync() removed in favor of pm_runtime_resume_and_get(). Now it also checks the return value of this function.
- Added pm_runtime_disable() and pm_runtime_put() to imx_rproc_remove() function.
v3 -> v4:
- Changed to use the new dev_pm_genpd_is_on() function instead, as suggested by Ulf. This will now get the power status of the two remote cores power domains to decided if imx_rpoc needs to attach or not. In order to do that, pm_runtime_enable() and pm_runtime_get_sync() were introduced and pd_data was removed.
v2 -> v3:
- Unchanged.
v1 -> v2:
- Dropped unecessary include. Removed the imx_rproc_is_on function, as suggested.

---
 drivers/remoteproc/imx_rproc.c | 37 +++++++++++++++++++++++++++++-----
 1 file changed, 32 insertions(+), 5 deletions(-)
drivers/remoteproc/imx_rproc.c +3 -4
index 627e57a88db2..24597b60c5b0 100644
@@ -18,6 +18,7 @@
 #include <linux/of_reserved_mem.h>
 #include <linux/platform_device.h>
 #include <linux/pm_domain.h>
+#include <linux/pm_runtime.h>
 #include <linux/reboot.h>
 #include <linux/regmap.h>
 #include <linux/remoteproc.h>
@@ -890,10 +891,8 @@ static int imx_rproc_partition_notify(struct notifier_block *nb,
 static int imx_rproc_attach_pd(struct imx_rproc *priv)
 {
 	struct device *dev = priv->dev;
-	int ret;
-	struct dev_pm_domain_attach_data pd_data = {
-		.pd_flags = PD_FLAG_DEV_LINK_ON,
-	};
+	int ret, i;
+	bool detached = true;
 
 	/*
 	 * If there is only one power-domain entry, the platform driver framework
@@ -902,7 +901,22 @@ static int imx_rproc_attach_pd(struct imx_rproc *priv)
 	if (dev->pm_domain)
 		return 0;
 
Quoted 16 lines

drivers/remoteproc/imx_rproc.c static int imx_rproc_attach_pd(struct imx_rproc *priv) · line 915

Quoted 13 lines
drivers/remoteproc/imx_rproc.c +12 -1
-	ret = dev_pm_domain_attach_list(dev, &pd_data, &priv->pd_list);
+	ret = dev_pm_domain_attach_list(dev, NULL, &priv->pd_list);
+	/*
+	 * If all the power domain devices are already turned on, the remote
+	 * core is already powered up and running when the kernel booted (e.g.,
+	 * started by U-Boot's bootaux command). In this case attach to it.
+	 */
+	for (i = 0; i < ret; i++) {
+		if (!dev_pm_genpd_is_on(priv->pd_list->pd_devs[i])) {
+			detached = false;
+			break;
+		}
+	}

I was doing one final review of this work when I noticed the return code for dev_pm_domain_attach_list() is never checked for error.

As Ulf pointed out, the 'return' a few lines below will return the negative value to the caller of 'imx_rproc_attach_pd', which ultimately will fail 'imx_rproc_detect_mode' and fail the probe of imx_rproc.

Quoted 5 lines

Please notice that even tough 'dev_pm_domain_attach_list' fails, the rproc->state will still be set as RPROC_DETACHED because we are starting 'detached' as true, but I am not seeing this as an issue because as mentioned above the probe will fail anyway. Please let me know if you see this as an issue.

Two things to consider here:

(1) It is only a matter of time before someone with a cleaver coccinelle script sends me a patch that adds the missing error check.

Quoted 7 lines

(2) I think that @rproc->state being changed on error conditions is a bug waiting to happen. This kind of implicit error handling is difficult to maintain and even more difficult for people to make enhancements to the driver.

Adding a simple error check will make sure neither of the above will happen. It is a simple change and we are at rc6 - this work can still go in the merge window.

Sure, I can submit a new revision with this error check. Sorry I did not see this before, I only had a close look at this '->state' now that you asked on the previous email.

Thanks,

Hiago.

Quoted 202 lines
Quoted 202 lines
Quoted 43 lines

Thanks,
Mathieu

Quoted 37 lines
drivers/remoteproc/imx_rproc.c +17 -0
+
+	if (detached)
+		priv->rproc->state = RPROC_DETACHED;
+
 	return ret < 0 ? ret : 0;
 }
 
@@ -1146,6 +1160,15 @@ static int imx_rproc_probe(struct platform_device *pdev)
 		}
 	}
 
+	if (dcfg->method == IMX_RPROC_SCU_API) {
+		pm_runtime_enable(dev);
+		ret = pm_runtime_resume_and_get(dev);
+		if (ret) {
+			dev_err(dev, "pm_runtime get failed: %d\n", ret);
+			goto err_put_clk;
+		}
+	}
+
 	ret = rproc_add(rproc);
 	if (ret) {
 		dev_err(dev, "rproc_add failed\n");
@@ -1171,6 +1194,10 @@ static void imx_rproc_remove(struct platform_device *pdev)
 	struct rproc *rproc = platform_get_drvdata(pdev);
 	struct imx_rproc *priv = rproc->priv;
 
+	if (priv->dcfg->method == IMX_RPROC_SCU_API) {
+		pm_runtime_disable(priv->dev);
+		pm_runtime_put(priv->dev);
+	}
 	clk_disable_unprepare(priv->clk);
 	rproc_del(rproc);
 	imx_rproc_put_scu(rproc);
Signature · 1 line
2.39.5
Quoted 143 lines · Ulf Hansson
Quoted 85 lines · Mathieu Poirier
Quoted 83 lines · Hiago De Franco

From: Hiago De Franco <[email protected]>

When the Cortex-M remote core is started and already running before Linux boots (typically by the Cortex-A bootloader using a command like bootaux), the current driver is unable to attach to it. This is because the driver only checks for remote cores running in different SCFW partitions. However in this case, the M-core is in the same partition as Linux and is already powered up and running by the bootloader.

This patch adds a check using dev_pm_genpd_is_on() to verify whether the M-core's power domains are already on. If all power domain devices are on, the driver assumes the M-core is running and proceed to attach to it.

To accomplish this, we need to avoid passing any attach_data or flags to dev_pm_domain_attach_list(), allowing the platform device become a consumer of the power domain provider without changing its current state.

During probe, also enable and sync the device runtime PM to make sure the power domains are correctly managed when the core is controlled by the kernel.

---
v6 -> v7:
- Added Peng reviewed-by.
v5 -> v6:
- Commit description improved, as suggested. Added Ulf Hansson reviewed by. Comment on imx-rproc.c improved.
v4 -> v5:
- pm_runtime_get_sync() removed in favor of pm_runtime_resume_and_get(). Now it also checks the return value of this function.
- Added pm_runtime_disable() and pm_runtime_put() to imx_rproc_remove() function.
v3 -> v4:
- Changed to use the new dev_pm_genpd_is_on() function instead, as suggested by Ulf. This will now get the power status of the two remote cores power domains to decided if imx_rpoc needs to attach or not. In order to do that, pm_runtime_enable() and pm_runtime_get_sync() were introduced and pd_data was removed.
v2 -> v3:
- Unchanged.
v1 -> v2:
- Dropped unecessary include. Removed the imx_rproc_is_on function, as suggested.

---
 drivers/remoteproc/imx_rproc.c | 37 +++++++++++++++++++++++++++++-----
 1 file changed, 32 insertions(+), 5 deletions(-)
drivers/remoteproc/imx_rproc.c +3 -4
index 627e57a88db2..24597b60c5b0 100644
@@ -18,6 +18,7 @@
 #include <linux/of_reserved_mem.h>
 #include <linux/platform_device.h>
 #include <linux/pm_domain.h>
+#include <linux/pm_runtime.h>
 #include <linux/reboot.h>
 #include <linux/regmap.h>
 #include <linux/remoteproc.h>
@@ -890,10 +891,8 @@ static int imx_rproc_partition_notify(struct notifier_block *nb,
 static int imx_rproc_attach_pd(struct imx_rproc *priv)
 {
      struct device *dev = priv->dev;
-     int ret;
-     struct dev_pm_domain_attach_data pd_data = {
-             .pd_flags = PD_FLAG_DEV_LINK_ON,
-     };
+     int ret, i;
+     bool detached = true;
 
      /*
       * If there is only one power-domain entry, the platform driver framework
@@ -902,7 +901,22 @@ static int imx_rproc_attach_pd(struct imx_rproc *priv)
      if (dev->pm_domain)
              return 0;
 
Quoted 16 lines

drivers/remoteproc/imx_rproc.c static int imx_rproc_attach_pd(struct imx_rproc *priv) · line 915

Quoted 13 lines
drivers/remoteproc/imx_rproc.c +12 -1
-     ret = dev_pm_domain_attach_list(dev, &pd_data, &priv->pd_list);
+     ret = dev_pm_domain_attach_list(dev, NULL, &priv->pd_list);
+     /*
+      * If all the power domain devices are already turned on, the remote
+      * core is already powered up and running when the kernel booted (e.g.,
+      * started by U-Boot's bootaux command). In this case attach to it.
+      */
+     for (i = 0; i < ret; i++) {
+             if (!dev_pm_genpd_is_on(priv->pd_list->pd_devs[i])) {
+                     detached = false;
+                     break;
+             }
+     }

I was doing one final review of this work when I noticed the return code for dev_pm_domain_attach_list() is never checked for error.

The for loop covers the error condition correctly, I think. It's only when ret >=1 when the loop should be started - and ret is propagated to the caller a few lines below.

Quoted 4 lines

Thanks,
Mathieu

Kind regards
Uffe

Quoted 27 lines
Quoted 27 lines
drivers/remoteproc/imx_rproc.c +13 -0
+
+     if (detached)
+             priv->rproc->state = RPROC_DETACHED;
+
      return ret < 0 ? ret : 0;
 }
 
@@ -1146,6 +1160,15 @@ static int imx_rproc_probe(struct platform_device *pdev)
              }
      }
 
+     if (dcfg->method == IMX_RPROC_SCU_API) {
+             pm_runtime_enable(dev);
+             ret = pm_runtime_resume_and_get(dev);
+             if (ret) {
+                     dev_err(dev, "pm_runtime get failed: %d\n", ret);
+                     goto err_put_clk;
+             }
+     }
+
      ret = rproc_add(rproc);
      if (ret) {
              dev_err(dev, "rproc_add failed\n");
@@ -1171,6 +1194,10 @@ static void imx_rproc_remove(struct platform_device *pdev)
      struct rproc *rproc = platform_get_drvdata(pdev);
      struct imx_rproc *priv = rproc->priv;
 
Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
drivers/remoteproc/imx_rproc.c +4 -1
+     if (priv->dcfg->method == IMX_RPROC_SCU_API) {
+             pm_runtime_disable(priv->dev);
+             pm_runtime_put(priv->dev);
+     }
      clk_disable_unprepare(priv->clk);
      rproc_del(rproc);
      imx_rproc_put_scu(rproc);
--

2.39.5

Best Regards,

Hiago.

#9 lore raw

Re: [PATCH v7 3/3] remoteproc: imx_rproc: detect and attach to pre-booted remote cores

Quoted 126 lines · Hiago De Franco
Quoted 124 lines · Mathieu Poirier
Quoted 108 lines · Hiago De Franco

Hi Mathieu, Ulf,

Quoted 84 lines · Mathieu Poirier
Quoted 83 lines · Hiago De Franco

From: Hiago De Franco <[email protected]>

When the Cortex-M remote core is started and already running before Linux boots (typically by the Cortex-A bootloader using a command like bootaux), the current driver is unable to attach to it. This is because the driver only checks for remote cores running in different SCFW partitions. However in this case, the M-core is in the same partition as Linux and is already powered up and running by the bootloader.

This patch adds a check using dev_pm_genpd_is_on() to verify whether the M-core's power domains are already on. If all power domain devices are on, the driver assumes the M-core is running and proceed to attach to it.

To accomplish this, we need to avoid passing any attach_data or flags to dev_pm_domain_attach_list(), allowing the platform device become a consumer of the power domain provider without changing its current state.

During probe, also enable and sync the device runtime PM to make sure the power domains are correctly managed when the core is controlled by the kernel.

---
v6 -> v7:
- Added Peng reviewed-by.
v5 -> v6:
- Commit description improved, as suggested. Added Ulf Hansson reviewed by. Comment on imx-rproc.c improved.
v4 -> v5:
- pm_runtime_get_sync() removed in favor of pm_runtime_resume_and_get(). Now it also checks the return value of this function.
- Added pm_runtime_disable() and pm_runtime_put() to imx_rproc_remove() function.
v3 -> v4:
- Changed to use the new dev_pm_genpd_is_on() function instead, as suggested by Ulf. This will now get the power status of the two remote cores power domains to decided if imx_rpoc needs to attach or not. In order to do that, pm_runtime_enable() and pm_runtime_get_sync() were introduced and pd_data was removed.
v2 -> v3:
- Unchanged.
v1 -> v2:
- Dropped unecessary include. Removed the imx_rproc_is_on function, as suggested.

---
 drivers/remoteproc/imx_rproc.c | 37 +++++++++++++++++++++++++++++-----
 1 file changed, 32 insertions(+), 5 deletions(-)
drivers/remoteproc/imx_rproc.c +3 -4
index 627e57a88db2..24597b60c5b0 100644
@@ -18,6 +18,7 @@
 #include <linux/of_reserved_mem.h>
 #include <linux/platform_device.h>
 #include <linux/pm_domain.h>
+#include <linux/pm_runtime.h>
 #include <linux/reboot.h>
 #include <linux/regmap.h>
 #include <linux/remoteproc.h>
@@ -890,10 +891,8 @@ static int imx_rproc_partition_notify(struct notifier_block *nb,
 static int imx_rproc_attach_pd(struct imx_rproc *priv)
 {
        struct device *dev = priv->dev;
-       int ret;
-       struct dev_pm_domain_attach_data pd_data = {
-               .pd_flags = PD_FLAG_DEV_LINK_ON,
-       };
+       int ret, i;
+       bool detached = true;
 
        /*
         * If there is only one power-domain entry, the platform driver framework
@@ -902,7 +901,22 @@ static int imx_rproc_attach_pd(struct imx_rproc *priv)
        if (dev->pm_domain)
                return 0;
 
Quoted 16 lines

drivers/remoteproc/imx_rproc.c static int imx_rproc_attach_pd(struct imx_rproc *priv) · line 915

Quoted 13 lines
drivers/remoteproc/imx_rproc.c +12 -1
-       ret = dev_pm_domain_attach_list(dev, &pd_data, &priv->pd_list);
+       ret = dev_pm_domain_attach_list(dev, NULL, &priv->pd_list);
+       /*
+        * If all the power domain devices are already turned on, the remote
+        * core is already powered up and running when the kernel booted (e.g.,
+        * started by U-Boot's bootaux command). In this case attach to it.
+        */
+       for (i = 0; i < ret; i++) {
+               if (!dev_pm_genpd_is_on(priv->pd_list->pd_devs[i])) {
+                       detached = false;
+                       break;
+               }
+       }

I was doing one final review of this work when I noticed the return code for dev_pm_domain_attach_list() is never checked for error.

As Ulf pointed out, the 'return' a few lines below will return the negative value to the caller of 'imx_rproc_attach_pd', which ultimately will fail 'imx_rproc_detect_mode' and fail the probe of imx_rproc.

Quoted 5 lines

Please notice that even tough 'dev_pm_domain_attach_list' fails, the rproc->state will still be set as RPROC_DETACHED because we are starting 'detached' as true, but I am not seeing this as an issue because as mentioned above the probe will fail anyway. Please let me know if you see this as an issue.

Two things to consider here:

(1) It is only a matter of time before someone with a cleaver coccinelle script sends me a patch that adds the missing error check.

(2) I think that @rproc->state being changed on error conditions is a bug waiting to happen. This kind of implicit error handling is difficult to maintain and even more difficult for people to make enhancements to the driver.

Quoted 7 lines
Quoted 3 lines

Adding a simple error check will make sure neither of the above will happen. It is a simple change and we are at rc6 - this work can still go in the merge window.

Sure, I can submit a new revision with this error check. Sorry I did not see this before, I only had a close look at this '->state' now that you asked on the previous email.

Alright. To avoid having you to resend patch1 and patch2 I have applied them on my next branch and added Mathieu's ack for patch2.

Note that my vacation is around the corner, so if you want patch3 for v6.17 you better be quick. :-)

[...]

Thanks and kind regards
Uffe

#10 lore raw

Re: [PATCH v7 3/3] remoteproc: imx_rproc: detect and attach to pre-booted remote cores

Quoted 135 lines · Ulf Hansson
Quoted 126 lines · Hiago De Franco
Quoted 124 lines · Mathieu Poirier
Quoted 108 lines · Hiago De Franco

Hi Mathieu, Ulf,

Quoted 84 lines · Mathieu Poirier
Quoted 83 lines · Hiago De Franco

From: Hiago De Franco <[email protected]>

When the Cortex-M remote core is started and already running before Linux boots (typically by the Cortex-A bootloader using a command like bootaux), the current driver is unable to attach to it. This is because the driver only checks for remote cores running in different SCFW partitions. However in this case, the M-core is in the same partition as Linux and is already powered up and running by the bootloader.

This patch adds a check using dev_pm_genpd_is_on() to verify whether the M-core's power domains are already on. If all power domain devices are on, the driver assumes the M-core is running and proceed to attach to it.

To accomplish this, we need to avoid passing any attach_data or flags to dev_pm_domain_attach_list(), allowing the platform device become a consumer of the power domain provider without changing its current state.

During probe, also enable and sync the device runtime PM to make sure the power domains are correctly managed when the core is controlled by the kernel.

---
v6 -> v7:
- Added Peng reviewed-by.
v5 -> v6:
- Commit description improved, as suggested. Added Ulf Hansson reviewed by. Comment on imx-rproc.c improved.
v4 -> v5:
- pm_runtime_get_sync() removed in favor of pm_runtime_resume_and_get(). Now it also checks the return value of this function.
- Added pm_runtime_disable() and pm_runtime_put() to imx_rproc_remove() function.
v3 -> v4:
- Changed to use the new dev_pm_genpd_is_on() function instead, as suggested by Ulf. This will now get the power status of the two remote cores power domains to decided if imx_rpoc needs to attach or not. In order to do that, pm_runtime_enable() and pm_runtime_get_sync() were introduced and pd_data was removed.
v2 -> v3:
- Unchanged.
v1 -> v2:
- Dropped unecessary include. Removed the imx_rproc_is_on function, as suggested.

---
 drivers/remoteproc/imx_rproc.c | 37 +++++++++++++++++++++++++++++-----
 1 file changed, 32 insertions(+), 5 deletions(-)
drivers/remoteproc/imx_rproc.c +3 -4
index 627e57a88db2..24597b60c5b0 100644
@@ -18,6 +18,7 @@
 #include <linux/of_reserved_mem.h>
 #include <linux/platform_device.h>
 #include <linux/pm_domain.h>
+#include <linux/pm_runtime.h>
 #include <linux/reboot.h>
 #include <linux/regmap.h>
 #include <linux/remoteproc.h>
@@ -890,10 +891,8 @@ static int imx_rproc_partition_notify(struct notifier_block *nb,
 static int imx_rproc_attach_pd(struct imx_rproc *priv)
 {
        struct device *dev = priv->dev;
-       int ret;
-       struct dev_pm_domain_attach_data pd_data = {
-               .pd_flags = PD_FLAG_DEV_LINK_ON,
-       };
+       int ret, i;
+       bool detached = true;
 
        /*
         * If there is only one power-domain entry, the platform driver framework
@@ -902,7 +901,22 @@ static int imx_rproc_attach_pd(struct imx_rproc *priv)
        if (dev->pm_domain)
                return 0;
 
Quoted 16 lines

drivers/remoteproc/imx_rproc.c static int imx_rproc_attach_pd(struct imx_rproc *priv) · line 915

Quoted 13 lines
drivers/remoteproc/imx_rproc.c +12 -1
-       ret = dev_pm_domain_attach_list(dev, &pd_data, &priv->pd_list);
+       ret = dev_pm_domain_attach_list(dev, NULL, &priv->pd_list);
+       /*
+        * If all the power domain devices are already turned on, the remote
+        * core is already powered up and running when the kernel booted (e.g.,
+        * started by U-Boot's bootaux command). In this case attach to it.
+        */
+       for (i = 0; i < ret; i++) {
+               if (!dev_pm_genpd_is_on(priv->pd_list->pd_devs[i])) {
+                       detached = false;
+                       break;
+               }
+       }

I was doing one final review of this work when I noticed the return code for dev_pm_domain_attach_list() is never checked for error.

As Ulf pointed out, the 'return' a few lines below will return the negative value to the caller of 'imx_rproc_attach_pd', which ultimately will fail 'imx_rproc_detect_mode' and fail the probe of imx_rproc.

Quoted 5 lines

Please notice that even tough 'dev_pm_domain_attach_list' fails, the rproc->state will still be set as RPROC_DETACHED because we are starting 'detached' as true, but I am not seeing this as an issue because as mentioned above the probe will fail anyway. Please let me know if you see this as an issue.

Two things to consider here:

(1) It is only a matter of time before someone with a cleaver coccinelle script sends me a patch that adds the missing error check.

(2) I think that @rproc->state being changed on error conditions is a bug waiting to happen. This kind of implicit error handling is difficult to maintain and even more difficult for people to make enhancements to the driver.

Quoted 7 lines
Quoted 3 lines

Adding a simple error check will make sure neither of the above will happen. It is a simple change and we are at rc6 - this work can still go in the merge window.

Sure, I can submit a new revision with this error check. Sorry I did not see this before, I only had a close look at this '->state' now that you asked on the previous email.

Quoted 5 lines

Alright. To avoid having you to resend patch1 and patch2 I have applied them on my next branch and added Mathieu's ack for patch2.

Note that my vacation is around the corner, so if you want patch3 for v6.17 you better be quick. :-)

Thanks Ulf, as requested I resend only patch 3.

https://lore.kernel.org/all/[email protected]/

Have a nice vacation =)

Best Regards,

Hiago.

Quoted 5 lines

[...]

Thanks and kind regards
Uffe

maintainer
#11 lore raw
In reply to Hiago De Franco

Hi Hiago,

Many thanks for re-working the changelog and comments in this patchset, things are much clearer now.

Thanks,
Mathieu

Quoted 55 lines · Hiago De Franco

From: Hiago De Franco <[email protected]>

This patch series depends on Ulf's patches that are currently under review, "pmdomain: Add generic ->sync_state() support to genpd" [1]. Without them, this series is not going to work.

For the i.MX8X and i.MX8 family SoCs, currently when the remotecore is started by the bootloader and the M core and A core are in the same partition, the driver is not capable to detect the remote core and report the correct state of it.

This patch series implement a new function, dev_pm_genpd_is_on(), which returns the power status of a given power domain (M core power domains IMX_SC_R_M4_0_PID0 and IMX_SC_R_M4_0_MU_1A in this case). If it is already powered on, the driver will attach to it.

Finally, the imx_rproc_clk_enable() function was also changed to make it return before dev_clk_get() is called, as it currently generates an SCU fault reset if the remote core is already running and the kernel tries to enable the clock again. These changes are a follow up from a v1 sent to imx_rproc [2] and from a reported regression [3].

[1] https://lore.kernel.org/all/[email protected]/
[2] https://lore.kernel.org/lkml/[email protected]/
[3] https://lore.kernel.org/lkml/20250404141713.ac2ntcsjsf7epdfa@hiago-nb/

v7:
- Added Peng reviewed-by.
v6:
- https://lore.kernel.org/all/[email protected]/
v5:
- https://lore.kernel.org/all/[email protected]/
v4:
- https://lore.kernel.org/lkml/[email protected]/
v3:
- https://lore.kernel.org/all/[email protected]/
v2:
- https://lore.kernel.org/lkml/[email protected]/
v1:
- https://lore.kernel.org/lkml/[email protected]/

Hiago De Franco (3):
pmdomain: core: introduce dev_pm_genpd_is_on()
remoteproc: imx_rproc: skip clock enable when M-core is managed by the
SCU
remoteproc: imx_rproc: detect and attach to pre-booted remote cores

 drivers/pmdomain/core.c        | 33 +++++++++++++++++++++++++++
 drivers/remoteproc/imx_rproc.c | 41 ++++++++++++++++++++++++++++------
 include/linux/pm_domain.h      |  6 +++++
 3 files changed, 73 insertions(+), 7 deletions(-)
Signature · 1 line
2.39.5
#12 lore raw

Hi Mathieu,

Quoted 15 lines · Mathieu Poirier

Hi Hiago,

Many thanks for re-working the changelog and comments in this patchset, things are much clearer now.

Thanks,
Mathieu

Quoted 5 lines · Hiago De Franco

From: Hiago De Franco <[email protected]>

This patch series depends on Ulf's patches that are currently under review, "pmdomain: Add generic ->sync_state() support to genpd" [1]. Without them, this series is not going to work.

The series above have been queued for v6.17 in my pmdomain tree.

Do I have your ack to pick $subject series via my pmdomain tree for v6.17 too or do you think it's better to postpone to v6.18?

Kind regards
Uffe

Quoted 50 lines
Quoted 50 lines

For the i.MX8X and i.MX8 family SoCs, currently when the remotecore is started by the bootloader and the M core and A core are in the same partition, the driver is not capable to detect the remote core and report the correct state of it.

This patch series implement a new function, dev_pm_genpd_is_on(), which returns the power status of a given power domain (M core power domains IMX_SC_R_M4_0_PID0 and IMX_SC_R_M4_0_MU_1A in this case). If it is already powered on, the driver will attach to it.

Finally, the imx_rproc_clk_enable() function was also changed to make it return before dev_clk_get() is called, as it currently generates an SCU fault reset if the remote core is already running and the kernel tries to enable the clock again. These changes are a follow up from a v1 sent to imx_rproc [2] and from a reported regression [3].

[1] https://lore.kernel.org/all/[email protected]/
[2] https://lore.kernel.org/lkml/[email protected]/
[3] https://lore.kernel.org/lkml/20250404141713.ac2ntcsjsf7epdfa@hiago-nb/

v7:
- Added Peng reviewed-by.
v6:
- https://lore.kernel.org/all/[email protected]/
v5:
- https://lore.kernel.org/all/[email protected]/
v4:
- https://lore.kernel.org/lkml/[email protected]/
v3:
- https://lore.kernel.org/all/[email protected]/
v2:
- https://lore.kernel.org/lkml/[email protected]/
v1:
- https://lore.kernel.org/lkml/[email protected]/

Hiago De Franco (3):
pmdomain: core: introduce dev_pm_genpd_is_on()
remoteproc: imx_rproc: skip clock enable when M-core is managed by the
SCU
remoteproc: imx_rproc: detect and attach to pre-booted remote cores

 drivers/pmdomain/core.c        | 33 +++++++++++++++++++++++++++
 drivers/remoteproc/imx_rproc.c | 41 ++++++++++++++++++++++++++++------
 include/linux/pm_domain.h      |  6 +++++
 3 files changed, 73 insertions(+), 7 deletions(-)

--
2.39.5

maintainer
#13 lore raw

Hi,

Quoted 15 lines · Ulf Hansson

Hi Mathieu,

Quoted 12 lines · Mathieu Poirier

Hi Hiago,

Many thanks for re-working the changelog and comments in this patchset, things are much clearer now.

Thanks,
Mathieu

Quoted 2 lines · Hiago De Franco

From: Hiago De Franco <[email protected]>

Quoted 9 lines
Quoted 3 lines
Quoted 3 lines

This patch series depends on Ulf's patches that are currently under review, "pmdomain: Add generic ->sync_state() support to genpd" [1]. Without them, this series is not going to work.

The series above have been queued for v6.17 in my pmdomain tree.

Do I have your ack to pick $subject series via my pmdomain tree for v6.17 too or do you think it's better to postpone to v6.18?

I may have spotted an error condition that is not handled properly in 3/3 of this series. Given that we are already at rc6, it is probably better to way for the next cycle.

Thanks for sheperding this work.

Quoted 53 lines

Kind regards
Uffe

Quoted 50 lines
Quoted 50 lines

For the i.MX8X and i.MX8 family SoCs, currently when the remotecore is started by the bootloader and the M core and A core are in the same partition, the driver is not capable to detect the remote core and report the correct state of it.

This patch series implement a new function, dev_pm_genpd_is_on(), which returns the power status of a given power domain (M core power domains IMX_SC_R_M4_0_PID0 and IMX_SC_R_M4_0_MU_1A in this case). If it is already powered on, the driver will attach to it.

Finally, the imx_rproc_clk_enable() function was also changed to make it return before dev_clk_get() is called, as it currently generates an SCU fault reset if the remote core is already running and the kernel tries to enable the clock again. These changes are a follow up from a v1 sent to imx_rproc [2] and from a reported regression [3].

[1] https://lore.kernel.org/all/[email protected]/
[2] https://lore.kernel.org/lkml/[email protected]/
[3] https://lore.kernel.org/lkml/20250404141713.ac2ntcsjsf7epdfa@hiago-nb/

v7:
- Added Peng reviewed-by.
v6:
- https://lore.kernel.org/all/[email protected]/
v5:
- https://lore.kernel.org/all/[email protected]/
v4:
- https://lore.kernel.org/lkml/[email protected]/
v3:
- https://lore.kernel.org/all/[email protected]/
v2:
- https://lore.kernel.org/lkml/[email protected]/
v1:
- https://lore.kernel.org/lkml/[email protected]/

Hiago De Franco (3):
pmdomain: core: introduce dev_pm_genpd_is_on()
remoteproc: imx_rproc: skip clock enable when M-core is managed by the
SCU
remoteproc: imx_rproc: detect and attach to pre-booted remote cores

 drivers/pmdomain/core.c        | 33 +++++++++++++++++++++++++++
 drivers/remoteproc/imx_rproc.c | 41 ++++++++++++++++++++++++++++------
 include/linux/pm_domain.h      |  6 +++++
 3 files changed, 73 insertions(+), 7 deletions(-)

--
2.39.5