Skip to contentSkip to conversation

further mt7988 devicetree work

PATCH In review Frank Wunderlich 5 participants 22 messages Jul 9, 2025 – Sep 9, 2025

Subsystems (5)
lore
Share & tools
lore
#0 lore raw

v9 cover further mt7988 devicetree work

From: Frank Wunderlich <[email protected]>

This series continues mt7988 devicetree work

- Extend cpu frequency scaling with CCI
- GPIO leds
- Basic network-support (ethernet controller + builtin switch + SFP Cages)

depencies (i hope this list is complete and latest patches/series linked):

support interrupt-names is optional again as i re-added the reserved IRQs (they are not unusable as i thought and can allow features in future)
https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/

needs change in mtk ethernet driver for the sram to be read from separate node:
https://patchwork.kernel.org/project/netdevbpf/patch/c2b9242229d06af4e468204bcf42daa1535c3a72.1751461762.git.daniel@makrotopia.org/

for SFP-Function (macs currently disabled):

PCS clearance which is a 1.5 year discussion currently ongoing

Daniel asked netdev for a way 2 go:
https://lore.kernel.org/netdev/[email protected]/

e.g. something like this (one of):
* https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/ (v6)
* https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/ (v4)
* https://patchwork.kernel.org/project/netdevbpf/patch/ba4e359584a6b3bc4b3470822c42186d5b0856f9.1721910728.git.daniel@makrotopia.org/

full usxgmii driver:
https://patchwork.kernel.org/project/netdevbpf/patch/07845ec900ba41ff992875dce12c622277592c32.1702352117.git.daniel@makrotopia.org/

first PCS-discussion is here:
https://patchwork.kernel.org/project/netdevbpf/patch/8aa905080bdb6760875d62cb3b2b41258837f80e.1702352117.git.daniel@makrotopia.org/
some more here:
https://lore.kernel.org/netdev/[email protected]/

and then dts nodes for sgmiisys+usxgmii+2g5 firmware

when above depencies are solved the mac1/2 can be enabled and 2.5G phy/SFP slots will work.

changes:
v9:
- dropped patches already applied (cci,gpio-leds,unused pins)
- added patches to add RSS IRQs, IRQ-names and sram-node for mt7986
note: mt7981 does not have a ethernet node yet
- set minItems for Filogic (MT798x) IRQs/Names to 8 needed to update MT7986 binding example because of this
- add sram:false to non-Filogic SoCs

v8:
- splitted binding into irq-count and irq-names and updated description
- fixed typo in mt7621 section "interrupt-namess"
- splitted binding changes into fixes (mac) and additions (sram)
- dropped change of reg (simple count to description)
- change ethernet register size to 0x40000

v7:
- fixed rebasing error while splitting dt-binding patch

v6:
binding:
- split out the interrupt-names into separate patch
- update irq(name) min count to 4
- move interrupt-names up
- add sram-property
- drop second reg entry and minitems as there is only 1 item left

dts:
- fix whitespace-errors for pdma irqs (spaces vs. tabs)
- move sram from eth reg to own sram node (needs CONFIG_SRAM)

v5:
- add reserved irqs and change names
- update binding for 8 irqs with different names (rx,tx => fe1+fe2, rx-ringX => pdmaX) (dropped Robs RB due to this change again, sorry)

v4:
net-binding:
- allow interrupt names and increase max interrupts to 6 because of RSS/LRO interrupts (dropped Robs RB due to this change)

dts-patches:
- add interrupts for RSS/LRO and interrupt-names for ethernet node
- eth-reg and clock whitespace-fix
- comment for fixed-link on gmac0
- drop phy-mode properties as suggested by andrew
- drop phy-connection-type on 2g5 board
- reorder some properties
- update 2g5 phy node
- unit-name dec instead of hex to match reg property
- move compatible before reg
- drop phy-mode

v3:
- dropped patches already applied (SPI+thermal)
- added soc specific cci compatible (new binding patch + changed dts)
- enable 2g5 phy because driver is now merged
- add patch for cleaning up unnecessary pins
- add patch for gpio-leds
- add patch for adding ethernet aliases

v2:
- change reg to list of items in eth binding
- changed mt7530 binding:
- unevaluatedProperties=false
- mediatek,pio subproperty
- from patternProperty to property
- board specific properties like led function and labels moved to bpi-r4 dtsi

Frank Wunderlich (13):
dt-bindings: net: mediatek,net: update mac subnode pattern for mt7988
dt-bindings: net: mediatek,net: allow up to 8 IRQs
dt-bindings: net: mediatek,net: allow irq names
dt-bindings: net: mediatek,net: add sram property
dt-bindings: net: dsa: mediatek,mt7530: add dsa-port definition for

    mt7988

dt-bindings: net: dsa: mediatek,mt7530: add internal mdio bus
arm64: dts: mediatek: mt7986: add sram node
arm64: dts: mediatek: mt7986: add interrupts for RSS and interrupt
names
arm64: dts: mediatek: mt7988: add basic ethernet-nodes
arm64: dts: mediatek: mt7988: add switch node
arm64: dts: mediatek: mt7988a-bpi-r4: add aliases for ethernet
arm64: dts: mediatek: mt7988a-bpi-r4: add sfp cages and link to gmac
arm64: dts: mediatek: mt7988a-bpi-r4: configure switch phys and leds

 .../bindings/net/dsa/mediatek,mt7530.yaml     |  24 +-
 .../devicetree/bindings/net/mediatek,net.yaml |  64 +++-
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi     |  20 +-
 .../mediatek/mt7988a-bananapi-bpi-r4-2g5.dts  |  11 +
 .../dts/mediatek/mt7988a-bananapi-bpi-r4.dts  |  19 ++
 .../dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi |  86 ++++++
 arch/arm64/boot/dts/mediatek/mt7988a.dtsi     | 285 +++++++++++++++++-
 7 files changed, 497 insertions(+), 12 deletions(-)
Signature · 1 line
2.43.0
#1 lore raw

PATCH v9 1/13 dt-bindings: net: mediatek,net: update mac subnode pattern for mt7988

From: Frank Wunderlich <[email protected]>

MT7888 have 3 Macs and so its nodes have names from mac0 - mac2. Update pattern to fix this.

Fixes c94a9aabec36 ("dt-bindings: net: mediatek,net: add mt7988-eth binding")
---
 Documentation/devicetree/bindings/net/mediatek,net.yaml | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
Documentation/devicetree/bindings/net/mediatek,net.yaml +1 -1
index 9e02fd80af83..175d1d011dc6 100644
@@ -382,7 +382,7 @@ allOf:
             - const: xgp3
 
 patternProperties:
-  "^mac@[0-1]$":
+  "^mac@[0-2]$":
     type: object
     unevaluatedProperties: false
     allOf:
Signature · 1 line
2.43.0
#2 lore raw

PATCH v9 2/13 dt-bindings: net: mediatek,net: allow up to 8 IRQs

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Increase the maximum IRQ count to 8 (4 FE + 4 RSS/LRO).

Frame-engine-IRQs (max 4):
MT7621, MT7628: 1 FE-IRQ
MT7622, MT7623: 3 FE-IRQs (only two used by the driver for now) MT7981, MT7986, MT7988: 4 FE-IRQs (only two used by the driver for now)

Mediatek Filogic SoCs (mt798x) have 4 additional IRQs for RSS and/or LRO. So MT798x have 8 IRQs in total.

MT7981 does not have a ethernet-node yet.
MT7986 Ethernet node is updated with RSS/LRO IRQs in this series. MT7988 Ethernet node is added in this series.

---
v9:
- set interrupt minitems to 8 for filogic
- mt7981 does not have a ethernet node yet, so no ABI break
- devicetree for mt7986 is updated later in this series, ABI-Break, but RSS/LRO should use interrupt names and is simply disabled when using older DT
- extend mt7986 example with PDMA-IRQs because minItems now 8
v8: separate irq-count change from interrupt-names patch

---
 .../devicetree/bindings/net/mediatek,net.yaml      | 14 +++++++++-----
 1 file changed, 9 insertions(+), 5 deletions(-)
Documentation/devicetree/bindings/net/mediatek,net.yaml +9 -5
index 175d1d011dc6..99dc0401eb9a 100644
@@ -40,7 +40,7 @@ properties:
 
   interrupts:
     minItems: 1
-    maxItems: 4
+    maxItems: 8
 
   power-domains:
     maxItems: 1
@@ -272,7 +272,7 @@ allOf:
     then:
       properties:
         interrupts:
-          minItems: 4
+          minItems: 8
 
         clocks:
           minItems: 15
@@ -310,7 +310,7 @@ allOf:
     then:
       properties:
         interrupts:
-          minItems: 4
+          minItems: 8
 
         clocks:
           minItems: 15
@@ -348,7 +348,7 @@ allOf:
     then:
       properties:
         interrupts:
-          minItems: 4
+          minItems: 8
 
         clocks:
           minItems: 24
@@ -507,7 +507,11 @@ examples:
         interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>,
                      <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>,
                      <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>,
-                     <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>;
+                     <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
         clocks = <&ethsys CLK_ETH_FE_EN>,
                  <&ethsys CLK_ETH_GP2_EN>,
                  <&ethsys CLK_ETH_GP1_EN>,
Signature · 1 line
2.43.0
Reviewed-by on v9 2/13
#3 lore raw

Re: [PATCH v9 02/13] dt-bindings: net: mediatek,net: allow up to 8 IRQs

Quoted 12 lines · Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Increase the maximum IRQ count to 8 (4 FE + 4 RSS/LRO).

Frame-engine-IRQs (max 4):
MT7621, MT7628: 1 FE-IRQ
MT7622, MT7623: 3 FE-IRQs (only two used by the driver for now) MT7981, MT7986, MT7988: 4 FE-IRQs (only two used by the driver for now)

Mediatek Filogic SoCs (mt798x) have 4 additional IRQs for RSS and/or LRO. So MT798x have 8 IRQs in total.

Quoted 6 lines

MT7981 does not have a ethernet-node yet.
MT7986 Ethernet node is updated with RSS/LRO IRQs in this series. MT7988 Ethernet node is added in this series.

---

Best regards,
Krzysztof

#4 lore raw

PATCH v9 3/13 dt-bindings: net: mediatek,net: allow irq names

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

In preparation for MT7988 and RSS/LRO allow the interrupt-names property.
In this way driver can request the interrupts by name which is much more readable in the driver code and SoC's dtsi than relying on a specific order.

Frame-engine-IRQs (fe0..3):
MT7621, MT7628: 1 FE-IRQ
MT7622, MT7623: 3 FE-IRQs (only two used by the driver for now) MT7981, MT7986: 4 FE-IRQs (only two used by the driver for now)

RSS/LRO IRQs (pdma0..3) additional only on Filogic (MT798x) with count of 4. So all IRQ-names (8) for Filogic.

Set boundaries for all compatibles same as irq count.

---
v9:
- add interrupt-names minitems to 8 for filogic
- mt7981 does not have a ethernet node yet
- devicetree for mt7986 is updated later in this series
- small rephrase IRQ => FE-IRQ and mention total count of IRQs on Filogic.
- kept angelos RB because of small change, i hope it is ok :)

v8:
- fixed typo in mt7621 section "interrupt-namess"
- separated interrupt count from interrupt-names
- rephrased description a bit to explain the "why"
v7: fixed wrong rebase
v6: new patch splitted from the mt7988 changes

---
 .../devicetree/bindings/net/mediatek,net.yaml | 36 +++++++++++++++++++
 1 file changed, 36 insertions(+)
Documentation/devicetree/bindings/net/mediatek,net.yaml +36 -0
index 99dc0401eb9a..d2b5461e73bc 100644
@@ -42,6 +42,18 @@ properties:
     minItems: 1
     maxItems: 8
 
+  interrupt-names:
+    minItems: 1
+    items:
+      - const: fe0
+      - const: fe1
+      - const: fe2
+      - const: fe3
+      - const: pdma0
+      - const: pdma1
+      - const: pdma2
+      - const: pdma3
+
   power-domains:
     maxItems: 1
 
@@ -135,6 +147,10 @@ allOf:
           minItems: 3
           maxItems: 3
 
+        interrupt-names:
+          minItems: 3
+          maxItems: 3
+
         clocks:
           minItems: 4
           maxItems: 4
@@ -166,6 +182,9 @@ allOf:
         interrupts:
           maxItems: 1
 
+        interrupt-names:
+          maxItems: 1
+
         clocks:
           minItems: 2
           maxItems: 2
@@ -192,6 +211,10 @@ allOf:
           minItems: 3
           maxItems: 3
 
+        interrupt-names:
+          minItems: 3
+          maxItems: 3
+
         clocks:
           minItems: 11
           maxItems: 11
@@ -232,6 +255,10 @@ allOf:
           minItems: 3
           maxItems: 3
 
+        interrupt-names:
+          minItems: 3
+          maxItems: 3
+
         clocks:
           minItems: 17
           maxItems: 17
@@ -274,6 +301,9 @@ allOf:
         interrupts:
           minItems: 8
 
+        interrupt-names:
+          minItems: 8
+
         clocks:
           minItems: 15
           maxItems: 15
@@ -312,6 +342,9 @@ allOf:
         interrupts:
           minItems: 8
 
+        interrupt-names:
+          minItems: 8
+
         clocks:
           minItems: 15
           maxItems: 15
@@ -350,6 +383,9 @@ allOf:
         interrupts:
           minItems: 8
 
+        interrupt-names:
+          minItems: 8
+
         clocks:
           minItems: 24
           maxItems: 24
Signature · 1 line
2.43.0
Reviewed-by on v9 3/13
#5 lore raw

Re: [PATCH v9 03/13] dt-bindings: net: mediatek,net: allow irq names

Quoted 13 lines · Frank Wunderlich

From: Frank Wunderlich <[email protected]>

In preparation for MT7988 and RSS/LRO allow the interrupt-names property.
In this way driver can request the interrupts by name which is much more readable in the driver code and SoC's dtsi than relying on a specific order.

Frame-engine-IRQs (fe0..3):
MT7621, MT7628: 1 FE-IRQ
MT7622, MT7623: 3 FE-IRQs (only two used by the driver for now) MT7981, MT7986: 4 FE-IRQs (only two used by the driver for now)

Quoted 8 lines

RSS/LRO IRQs (pdma0..3) additional only on Filogic (MT798x) with count of 4. So all IRQ-names (8) for Filogic.

Set boundaries for all compatibles same as irq count.

---

Best regards,
Krzysztof

#6 lore raw

PATCH v9 4/13 dt-bindings: net: mediatek,net: add sram property

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Meditak Filogic SoCs (MT798x) have dedicated MMIO-SRAM for dma operations.

MT7981 and MT7986 currently use static offset to ethernet MAC register which will be changed in separate patch once this way is accepted.

Add "sram" property to map ethernet controller to dedicated mmio-sram node.

---
v9:
- add "sram: false" for non-filogic

v8:
- splitted out mac subnode pattern
- dropped reg naming change
- rephrased description
- drop change of reg-name

v6:
- split out the interrupt-names into separate patch
- update irq(name) min count to 4
- add sram-property
- drop second reg entry and minitems as there is only 1 item left again

v5:
- fix v4 logmessage and change description a bit describing how i get the irq count.
- update binding for 8 irqs with different names (rx,tx => fe0..fe3) including the 2 reserved irqs which can be used later
- change rx-ringX to pdmaX to be closer to hardware documentation

v4:
- increase max interrupts to 6 because of adding RSS/LRO interrupts (4) and dropping 2 reserved irqs (0+3) around rx+tx
- dropped Robs RB due to this change
- allow interrupt names
- add interrupt-names without reserved IRQs on mt7988
this requires mtk driver patch:
https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/

v2:
- change reg to list of items

---
 .../devicetree/bindings/net/mediatek,net.yaml        | 12 ++++++++++++
 1 file changed, 12 insertions(+)
Documentation/devicetree/bindings/net/mediatek,net.yaml +12 -0
index d2b5461e73bc..b45f67f92e80 100644
@@ -66,6 +66,10 @@ properties:
       - const: gmac
       - const: ppe
 
+  sram:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: phandle to mmio SRAM
+
   mediatek,ethsys:
     $ref: /schemas/types.yaml#/definitions/phandle
     description:
@@ -162,6 +166,8 @@ allOf:
             - const: gp1
             - const: gp2
 
+        sram: false
+
         mediatek,infracfg: false
 
         mediatek,wed: false
@@ -194,6 +200,8 @@ allOf:
             - const: ethif
             - const: fe
 
+        sram: false
+
         mediatek,infracfg: false
 
         mediatek,wed: false
@@ -233,6 +241,8 @@ allOf:
             - const: sgmii_ck
             - const: eth2pll
 
+        sram: false
+
         mediatek,infracfg: false
 
         mediatek,sgmiisys:
@@ -283,6 +293,8 @@ allOf:
             - const: sgmii_ck
             - const: eth2pll
 
+        sram: false
+
         mediatek,sgmiisys:
           minItems: 2
           maxItems: 2
Signature · 1 line
2.43.0
Reviewed-by on v9 4/13
#7 lore raw

Re: [PATCH v9 04/13] dt-bindings: net: mediatek,net: add sram property

Quoted 4 lines · Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Meditak Filogic SoCs (MT798x) have dedicated MMIO-SRAM for dma operations.

Quoted 8 lines

MT7981 and MT7986 currently use static offset to ethernet MAC register which will be changed in separate patch once this way is accepted.

Add "sram" property to map ethernet controller to dedicated mmio-sram node.

---

Best regards,
Krzysztof

#8 lore raw

PATCH v9 5/13 dt-bindings: net: dsa: mediatek,mt7530: add dsa-port definition for mt7988

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Add own dsa-port binding for SoC with internal switch where only phy-mode 'internal' is valid.

---
 .../bindings/net/dsa/mediatek,mt7530.yaml          | 14 +++++++++++++-
 1 file changed, 13 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml +13 -1
index 51205f9f2985..9b983fdbf3c7 100644
@@ -190,6 +190,18 @@ required:
   - reg
 
 $defs:
+  builtin-dsa-port:
+    patternProperties:
+      "^(ethernet-)?ports$":
+        patternProperties:
+          "^(ethernet-)?port@[0-6]$":
+            if:
+              required: [ ethernet ]
+            then:
+              properties:
+                phy-mode:
+                  const: internal
+
   mt7530-dsa-port:
     patternProperties:
       "^(ethernet-)?ports$":
@@ -297,7 +309,7 @@ allOf:
             - airoha,en7581-switch
             - airoha,an7583-switch
     then:
-      $ref: "#/$defs/mt7530-dsa-port"
+      $ref: "#/$defs/builtin-dsa-port"
       properties:
         gpio-controller: false
         mediatek,mcm: false
Signature · 1 line
2.43.0
#9 lore raw

PATCH v9 6/13 dt-bindings: net: dsa: mediatek,mt7530: add internal mdio bus

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Mt7988 buildin switch has own mdio bus where ge-phys are connected. Add related property for this.

---
v2:
- change from patternproperty to property
- add unevaluatedProperties and mediatek,pio subproperty

---
 .../devicetree/bindings/net/dsa/mediatek,mt7530.yaml   | 10 ++++++++++
 1 file changed, 10 insertions(+)
Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml +10 -0
index 9b983fdbf3c7..815a90808901 100644
@@ -136,6 +136,16 @@ properties:
       See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt for
       details for the regulator setup on these boards.
 
+  mdio:
+    $ref: /schemas/net/mdio.yaml#
+    unevaluatedProperties: false
+
+    properties:
+      mediatek,pio:
+        $ref: /schemas/types.yaml#/definitions/phandle
+        description:
+          Phandle pointing to the mediatek pinctrl node.
+
   mediatek,mcm:
     type: boolean
     description:
Signature · 1 line
2.43.0
#10 lore raw

PATCH v9 7/13 arm64: dts: mediatek: mt7986: add sram node

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Currently sram is allocated in driver via offset from reg of ethernet node. Change it to use a dedicated sram node like mt7988.

---
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 12 +++++++++++-
 1 file changed, 11 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/mediatek/mt7986a.dtsi +11 -1
index 559990dcd1d1..550f569451fb 100644
@@ -523,7 +523,7 @@ wed1: wed@15011000 {
 
 		eth: ethernet@15100000 {
 			compatible = "mediatek,mt7986-eth";
-			reg = <0 0x15100000 0 0x80000>;
+			reg = <0 0x15100000 0 0x40000>;
 			interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>,
@@ -553,6 +553,7 @@ eth: ethernet@15100000 {
 					  <&topckgen CLK_TOP_SGM_325M_SEL>;
 			assigned-clock-parents = <&apmixedsys CLK_APMIXED_NET2PLL>,
 						 <&apmixedsys CLK_APMIXED_SGMPLL>;
+			sram = <&eth_sram>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			mediatek,ethsys = <&ethsys>;
@@ -562,6 +563,15 @@ eth: ethernet@15100000 {
 			status = "disabled";
 		};
 
+		/*15100000+0x40000*/
+		eth_sram: sram@15140000 {
+			compatible = "mmio-sram";
+			reg = <0 0x15140000 0 0x40000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x15140000 0 0x40000>;
+		};
+
 		wo_ccif0: syscon@151a5000 {
 			compatible = "mediatek,mt7986-wo-ccif", "syscon";
 			reg = <0 0x151a5000 0 0x1000>;
Signature · 1 line
2.43.0
#11 lore raw

PATCH v9 8/13 arm64: dts: mediatek: mt7986: add interrupts for RSS and interrupt names

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Add interrupts for RSS/LRO and names to access them via name instead of index.

---
 arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)
arch/arm64/boot/dts/mediatek/mt7986a.dtsi +7 -1
index 550f569451fb..a9e079fd42c6 100644
@@ -527,7 +527,13 @@ eth: ethernet@15100000 {
 			interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>;
+				     <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "fe0", "fe1", "fe2", "fe3", "pdma0",
+					  "pdma1", "pdma2", "pdma3";
 			clocks = <&ethsys CLK_ETH_FE_EN>,
 				 <&ethsys CLK_ETH_GP2_EN>,
 				 <&ethsys CLK_ETH_GP1_EN>,
Signature · 1 line
2.43.0
#12 lore raw

PATCH v9 9/13 arm64: dts: mediatek: mt7988: add basic ethernet-nodes

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Add basic ethernet related nodes.

Mac1+2 needs pcs (sgmii+usxgmii) to work correctly which will be linked later when driver is merged.

---
v8:
- change ethernet register size to 0x40000
range from 0x15140000 ~ 0x1517ffff is not usable on mt7988 => 0xDEADBEEF

v6:
- fix whitespace-errors for pdma irqs (spaces vs. tabs)
- move sram from eth reg to own sram node (needs CONFIG_SRAM)

v5:
- add reserved irqs and change names to fe0..fe3
- change rx-ringX to pdmaX to be closer to documentation

v4:
- comment for fixed-link on gmac0
- update 2g5 phy node
- unit-name dec instead of hex to match reg property
- move compatible before reg
- drop phy-mode
- add interrupts for RSS
- add interrupt-names and drop reserved irqs for ethernet
- some reordering
- eth-reg and clock whitespace-fix based on angelos review

---
 arch/arm64/boot/dts/mediatek/mt7988a.dtsi | 137 +++++++++++++++++++++-
 1 file changed, 134 insertions(+), 3 deletions(-)
arch/arm64/boot/dts/mediatek/mt7988a.dtsi +134 -3
index 560ec86dbec0..897b5a82b53e 100644
@@ -680,7 +680,28 @@ xphyu3port0: usb-phy@11e13000 {
 			};
 		};
 
-		clock-controller@11f40000 {
+		xfi_tphy0: phy@11f20000 {
+			compatible = "mediatek,mt7988-xfi-tphy";
+			reg = <0 0x11f20000 0 0x10000>;
+			clocks = <&xfi_pll CLK_XFIPLL_PLL_EN>,
+				 <&topckgen CLK_TOP_XFI_PHY_0_XTAL_SEL>;
+			clock-names = "xfipll", "topxtal";
+			resets = <&watchdog 14>;
+			mediatek,usxgmii-performance-errata;
+			#phy-cells = <0>;
+		};
+
+		xfi_tphy1: phy@11f30000 {
+			compatible = "mediatek,mt7988-xfi-tphy";
+			reg = <0 0x11f30000 0 0x10000>;
+			clocks = <&xfi_pll CLK_XFIPLL_PLL_EN>,
+				 <&topckgen CLK_TOP_XFI_PHY_1_XTAL_SEL>;
+			clock-names = "xfipll", "topxtal";
+			resets = <&watchdog 15>;
+			#phy-cells = <0>;
+		};
+
+		xfi_pll: clock-controller@11f40000 {
 			compatible = "mediatek,mt7988-xfi-pll";
 			reg = <0 0x11f40000 0 0x1000>;
 			resets = <&watchdog 16>;
@@ -714,19 +735,129 @@ phy_calibration_p3: calib@97c {
 			};
 		};
 
-		clock-controller@15000000 {
+		ethsys: clock-controller@15000000 {
 			compatible = "mediatek,mt7988-ethsys", "syscon";
 			reg = <0 0x15000000 0 0x1000>;
 			#clock-cells = <1>;
 			#reset-cells = <1>;
 		};
 
-		clock-controller@15031000 {
+		ethwarp: clock-controller@15031000 {
 			compatible = "mediatek,mt7988-ethwarp";
 			reg = <0 0x15031000 0 0x1000>;
 			#clock-cells = <1>;
 			#reset-cells = <1>;
 		};
+
+		eth: ethernet@15100000 {
+			compatible = "mediatek,mt7988-eth";
+			reg = <0 0x15100000 0 0x40000>;
+			interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "fe0", "fe1", "fe2", "fe3", "pdma0",
+					  "pdma1", "pdma2", "pdma3";
+			clocks = <&ethsys CLK_ETHDMA_CRYPT0_EN>,
+				 <&ethsys CLK_ETHDMA_FE_EN>,
+				 <&ethsys CLK_ETHDMA_GP2_EN>,
+				 <&ethsys CLK_ETHDMA_GP1_EN>,
+				 <&ethsys CLK_ETHDMA_GP3_EN>,
+				 <&ethwarp CLK_ETHWARP_WOCPU2_EN>,
+				 <&ethwarp CLK_ETHWARP_WOCPU1_EN>,
+				 <&ethwarp CLK_ETHWARP_WOCPU0_EN>,
+				 <&ethsys CLK_ETHDMA_ESW_EN>,
+				 <&topckgen CLK_TOP_ETH_GMII_SEL>,
+				 <&topckgen CLK_TOP_ETH_REFCK_50M_SEL>,
+				 <&topckgen CLK_TOP_ETH_SYS_200M_SEL>,
+				 <&topckgen CLK_TOP_ETH_SYS_SEL>,
+				 <&topckgen CLK_TOP_ETH_XGMII_SEL>,
+				 <&topckgen CLK_TOP_ETH_MII_SEL>,
+				 <&topckgen CLK_TOP_NETSYS_SEL>,
+				 <&topckgen CLK_TOP_NETSYS_500M_SEL>,
+				 <&topckgen CLK_TOP_NETSYS_PAO_2X_SEL>,
+				 <&topckgen CLK_TOP_NETSYS_SYNC_250M_SEL>,
+				 <&topckgen CLK_TOP_NETSYS_PPEFB_250M_SEL>,
+				 <&topckgen CLK_TOP_NETSYS_WARP_SEL>,
+				 <&ethsys CLK_ETHDMA_XGP1_EN>,
+				 <&ethsys CLK_ETHDMA_XGP2_EN>,
+				 <&ethsys CLK_ETHDMA_XGP3_EN>;
+			clock-names = "crypto", "fe", "gp2", "gp1", "gp3",
+				      "ethwarp_wocpu2", "ethwarp_wocpu1",
+				      "ethwarp_wocpu0", "esw", "top_eth_gmii_sel",
+				      "top_eth_refck_50m_sel", "top_eth_sys_200m_sel",
+				      "top_eth_sys_sel", "top_eth_xgmii_sel",
+				      "top_eth_mii_sel", "top_netsys_sel",
+				      "top_netsys_500m_sel", "top_netsys_pao_2x_sel",
+				      "top_netsys_sync_250m_sel",
+				      "top_netsys_ppefb_250m_sel",
+				      "top_netsys_warp_sel","xgp1", "xgp2", "xgp3";
+			assigned-clocks = <&topckgen CLK_TOP_NETSYS_2X_SEL>,
+					  <&topckgen CLK_TOP_NETSYS_GSW_SEL>,
+					  <&topckgen CLK_TOP_USXGMII_SBUS_0_SEL>,
+					  <&topckgen CLK_TOP_USXGMII_SBUS_1_SEL>,
+					  <&topckgen CLK_TOP_SGM_0_SEL>,
+					  <&topckgen CLK_TOP_SGM_1_SEL>;
+			assigned-clock-parents = <&apmixedsys CLK_APMIXED_NET2PLL>,
+						 <&topckgen CLK_TOP_NET1PLL_D4>,
+						 <&topckgen CLK_TOP_NET1PLL_D8_D4>,
+						 <&topckgen CLK_TOP_NET1PLL_D8_D4>,
+						 <&apmixedsys CLK_APMIXED_SGMPLL>,
+						 <&apmixedsys CLK_APMIXED_SGMPLL>;
+			sram = <&eth_sram>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			mediatek,ethsys = <&ethsys>;
+			mediatek,infracfg = <&topmisc>;
+
+			gmac0: mac@0 {
+				compatible = "mediatek,eth-mac";
+				reg = <0>;
+				phy-mode = "internal";
+
+				/* Connected to internal switch */
+				fixed-link {
+					speed = <10000>;
+					full-duplex;
+					pause;
+				};
+			};
+
+			gmac1: mac@1 {
+				compatible = "mediatek,eth-mac";
+				reg = <1>;
+				status = "disabled";
+			};
+
+			gmac2: mac@2 {
+				compatible = "mediatek,eth-mac";
+				reg = <2>;
+				status = "disabled";
+			};
+
+			mdio_bus: mdio-bus {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				/* internal 2.5G PHY */
+				int_2p5g_phy: ethernet-phy@15 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <15>;
+				};
+			};
+		};
+
+		eth_sram: sram@15400000 {
+			compatible = "mmio-sram";
+			reg = <0 0x15400000 0 0x200000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x15400000 0 0x200000>;
+		};
 	};
 
 	thermal-zones {
Signature · 1 line
2.43.0
#13 lore raw

PATCH v9 10/13 arm64: dts: mediatek: mt7988: add switch node

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Add mt7988 builtin mt753x switch nodes.

---
v4:
- drop phy-mode for gsw-phy
- reorder phy-mode after phy-handle
- drop interrupt parent from switch

v2:
- drop labels and led-function too (have to be in board)

---
 arch/arm64/boot/dts/mediatek/mt7988a.dtsi | 148 ++++++++++++++++++++++
 1 file changed, 148 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a.dtsi +148 -0
index 897b5a82b53e..366203a72d6d 100644
@@ -742,6 +742,154 @@ ethsys: clock-controller@15000000 {
 			#reset-cells = <1>;
 		};
 
+		switch: switch@15020000 {
+			compatible = "mediatek,mt7988-switch";
+			reg = <0 0x15020000 0 0x8000>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&ethwarp MT7988_ETHWARP_RST_SWITCH>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				gsw_port0: port@0 {
+					reg = <0>;
+					phy-handle = <&gsw_phy0>;
+					phy-mode = "internal";
+				};
+
+				gsw_port1: port@1 {
+					reg = <1>;
+					phy-handle = <&gsw_phy1>;
+					phy-mode = "internal";
+				};
+
+				gsw_port2: port@2 {
+					reg = <2>;
+					phy-handle = <&gsw_phy2>;
+					phy-mode = "internal";
+				};
+
+				gsw_port3: port@3 {
+					reg = <3>;
+					phy-handle = <&gsw_phy3>;
+					phy-mode = "internal";
+				};
+
+				port@6 {
+					reg = <6>;
+					ethernet = <&gmac0>;
+					phy-mode = "internal";
+
+					fixed-link {
+						speed = <10000>;
+						full-duplex;
+						pause;
+					};
+				};
+			};
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				mediatek,pio = <&pio>;
+
+				gsw_phy0: ethernet-phy@0 {
+					compatible = "ethernet-phy-ieee802.3-c22";
+					reg = <0>;
+					interrupts = <0>;
+					nvmem-cells = <&phy_calibration_p0>;
+					nvmem-cell-names = "phy-cal-data";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						gsw_phy0_led0: led@0 {
+							reg = <0>;
+							status = "disabled";
+						};
+
+						gsw_phy0_led1: led@1 {
+							reg = <1>;
+							status = "disabled";
+						};
+					};
+				};
+
+				gsw_phy1: ethernet-phy@1 {
+					compatible = "ethernet-phy-ieee802.3-c22";
+					reg = <1>;
+					interrupts = <1>;
+					nvmem-cells = <&phy_calibration_p1>;
+					nvmem-cell-names = "phy-cal-data";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						gsw_phy1_led0: led@0 {
+							reg = <0>;
+							status = "disabled";
+						};
+
+						gsw_phy1_led1: led@1 {
+							reg = <1>;
+							status = "disabled";
+						};
+					};
+				};
+
+				gsw_phy2: ethernet-phy@2 {
+					compatible = "ethernet-phy-ieee802.3-c22";
+					reg = <2>;
+					interrupts = <2>;
+					nvmem-cells = <&phy_calibration_p2>;
+					nvmem-cell-names = "phy-cal-data";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						gsw_phy2_led0: led@0 {
+							reg = <0>;
+							status = "disabled";
+						};
+
+						gsw_phy2_led1: led@1 {
+							reg = <1>;
+							status = "disabled";
+						};
+					};
+				};
+
+				gsw_phy3: ethernet-phy@3 {
+					compatible = "ethernet-phy-ieee802.3-c22";
+					reg = <3>;
+					interrupts = <3>;
+					nvmem-cells = <&phy_calibration_p3>;
+					nvmem-cell-names = "phy-cal-data";
+
+					leds {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						gsw_phy3_led0: led@0 {
+							reg = <0>;
+							status = "disabled";
+						};
+
+						gsw_phy3_led1: led@1 {
+							reg = <1>;
+							status = "disabled";
+						};
+					};
+				};
+			};
+		};
+
 		ethwarp: clock-controller@15031000 {
 			compatible = "mediatek,mt7988-ethwarp";
 			reg = <0 0x15031000 0 0x1000>;
Signature · 1 line
2.43.0
#14 lore raw

PATCH v9 11/13 arm64: dts: mediatek: mt7988a-bpi-r4: add aliases for ethernet

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Add aliases for gmacs to allow bootloader setting mac-adresses.

---
 arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi +6 -0
index 21eb91c8609f..20073eb4d1bd 100644
@@ -8,6 +8,12 @@
 #include "mt7988a.dtsi"
 
 / {
+	aliases {
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
+		ethernet2 = &gmac2;
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
Signature · 1 line
2.43.0
#15 lore raw

PATCH v9 12/13 arm64: dts: mediatek: mt7988a-bpi-r4: add sfp cages and link to gmac

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Add SFP cages to Bananapi-R4 board. The 2.5g phy variant only contains the wan-SFP, so add this to common dtsi and the lan-sfp only to the dual-SFP variant.

---
v4:
- update 2g5-board (reorder and drop phy-connection-type)
- order sfp properties
v3:
- enable mac with 2.5g phy on r4 phy variant because driver is now mainline

---
 .../mediatek/mt7988a-bananapi-bpi-r4-2g5.dts  | 11 +++++++++++
 .../dts/mediatek/mt7988a-bananapi-bpi-r4.dts  | 19 +++++++++++++++++++
 .../dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 19 +++++++++++++++++++
 3 files changed, 49 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4-2g5.dts +11 -0
index 53de9c113f60..6f0c81e3fd94 100644
@@ -9,3 +9,14 @@ / {
 	model = "Banana Pi BPI-R4 (1x SFP+, 1x 2.5GbE)";
 	chassis-type = "embedded";
 };
+
+&gmac1 {
+	phy = <&int_2p5g_phy>;
+	phy-mode = "internal";
+	status = "okay";
+};
+
+&int_2p5g_phy {
+	pinctrl-0 = <&i2p5gbe_led0_pins>;
+	pinctrl-names = "i2p5gbe-led";
+};
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dts +19 -0
index 36bd1ef2efab..4b3796ba82e3 100644
@@ -8,6 +8,25 @@ / {
 	compatible = "bananapi,bpi-r4", "mediatek,mt7988a";
 	model = "Banana Pi BPI-R4 (2x SFP+)";
 	chassis-type = "embedded";
+
+	/* SFP2 cage (LAN) */
+	sfp2: sfp2 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp2>;
+		maximum-power-milliwatt = <3000>;
+
+		los-gpios = <&pio 2 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&pio 83 GPIO_ACTIVE_LOW>;
+		rate-select0-gpios = <&pio 3 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&pio 0 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&pio 1 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&gmac1 {
+	managed = "in-band-status";
+	phy-mode = "usxgmii";
+	sfp = <&sfp2>;
 };
 
 &pca9545 {
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi +19 -0
index 20073eb4d1bd..4d709ee527df 100644
@@ -63,6 +63,19 @@ reg_3p3v: regulator-3p3v {
 		regulator-boot-on;
 		regulator-always-on;
 	};
+
+	/* SFP1 cage (WAN) */
+	sfp1: sfp1 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp1>;
+		maximum-power-milliwatt = <3000>;
+
+		los-gpios = <&pio 54 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&pio 82 GPIO_ACTIVE_LOW>;
+		rate-select0-gpios = <&pio 21 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&pio 70 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&pio 69 GPIO_ACTIVE_HIGH>;
+	};
 };
 
 &cci {
@@ -133,6 +146,12 @@ map-cpu-active-low {
 	};
 };
 
+&gmac2 {
+	managed = "in-band-status";
+	phy-mode = "usxgmii";
+	sfp = <&sfp1>;
+};
+
 &i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_pins>;
Signature · 1 line
2.43.0
#16 lore raw

PATCH v9 13/13 arm64: dts: mediatek: mt7988a-bpi-r4: configure switch phys and leds

In reply to Frank Wunderlich

From: Frank Wunderlich <[email protected]>

Assign pinctrl to switch phys and leds.

---
v4:
- reorder switch phy(-led) properties
v2:
- add labels and led-function and include after dropping from soc dtsi

---
 .../dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi | 61 +++++++++++++++++++
 1 file changed, 61 insertions(+)
arch/arm64/boot/dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi +61 -0
index 4d709ee527df..7c9df606f60d 100644
@@ -4,6 +4,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/regulator/richtek,rt5190a-regulator.h>
+#include <dt-bindings/leds/common.h>
 
 #include "mt7988a.dtsi"
 
@@ -152,6 +153,66 @@ &gmac2 {
 	sfp = <&sfp1>;
 };
 
+&gsw_phy0 {
+	pinctrl-0 = <&gbe0_led0_pins>;
+	pinctrl-names = "gbe-led";
+};
+
+&gsw_phy0_led0 {
+	function = LED_FUNCTION_WAN;
+	color = <LED_COLOR_ID_GREEN>;
+	status = "okay";
+};
+
+&gsw_port0 {
+	label = "wan";
+};
+
+&gsw_phy1 {
+	pinctrl-0 = <&gbe1_led0_pins>;
+	pinctrl-names = "gbe-led";
+};
+
+&gsw_phy1_led0 {
+	function = LED_FUNCTION_LAN;
+	color = <LED_COLOR_ID_GREEN>;
+	status = "okay";
+};
+
+&gsw_port1 {
+	label = "lan1";
+};
+
+&gsw_phy2 {
+	pinctrl-0 = <&gbe2_led0_pins>;
+	pinctrl-names = "gbe-led";
+};
+
+&gsw_phy2_led0 {
+	function = LED_FUNCTION_LAN;
+	color = <LED_COLOR_ID_GREEN>;
+	status = "okay";
+};
+
+&gsw_port2 {
+	label = "lan2";
+};
+
+&gsw_phy3 {
+	pinctrl-0 = <&gbe3_led0_pins>;
+	pinctrl-names = "gbe-led";
+};
+
+&gsw_phy3_led0 {
+	function = LED_FUNCTION_LAN;
+	color = <LED_COLOR_ID_GREEN>;
+	status = "okay";
+};
+
+&gsw_port3 {
+	label = "lan3";
+};
+
 &i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_pins>;
Signature · 1 line
2.43.0
#17 lore raw
In reply to Frank Wunderlich
This series was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:

Hello:

This series was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:

Quoted 9 lines · On Wed, 9 Jul 2025 13:09:36 +0200 you wrote:

From: Frank Wunderlich <[email protected]>

This series continues mt7988 devicetree work

- Extend cpu frequency scaling with CCI
- GPIO leds
- Basic network-support (ethernet controller + builtin switch + SFP Cages)

[...]

Here is the summary with links:
- [v9,01/13] dt-bindings: net: mediatek,net: update mac subnode pattern for mt7988

    https://git.kernel.org/netdev/net-next/c/29712b437339
  - [v9,02/13] dt-bindings: net: mediatek,net: allow up to 8 IRQs
    https://git.kernel.org/netdev/net-next/c/356dea0baf4c
  - [v9,03/13] dt-bindings: net: mediatek,net: allow irq names
    https://git.kernel.org/netdev/net-next/c/23ac2a71bdbd
  - [v9,04/13] dt-bindings: net: mediatek,net: add sram property
    https://git.kernel.org/netdev/net-next/c/c4582a31efd9
  - [v9,05/13] dt-bindings: net: dsa: mediatek,mt7530: add dsa-port definition for mt7988
    https://git.kernel.org/netdev/net-next/c/588cb646ce70
  - [v9,06/13] dt-bindings: net: dsa: mediatek,mt7530: add internal mdio bus
    https://git.kernel.org/netdev/net-next/c/66a44adf4c3d

- [v9,07/13] arm64: dts: mediatek: mt7986: add sram node
(no matching commit)
- [v9,08/13] arm64: dts: mediatek: mt7986: add interrupts for RSS and interrupt names (no matching commit)
- [v9,09/13] arm64: dts: mediatek: mt7988: add basic ethernet-nodes
(no matching commit)
- [v9,10/13] arm64: dts: mediatek: mt7988: add switch node
(no matching commit)
- [v9,11/13] arm64: dts: mediatek: mt7988a-bpi-r4: add aliases for ethernet (no matching commit)
- [v9,12/13] arm64: dts: mediatek: mt7988a-bpi-r4: add sfp cages and link to gmac (no matching commit)
- [v9,13/13] arm64: dts: mediatek: mt7988a-bpi-r4: configure switch phys and leds (no matching commit)

You are awesome, thank you!

Signature · 2 lines
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html
#18 lore raw

Am 11. Juli 2025 00:10:22 MESZ schrieb [email protected]:

Quoted 44 lines

Hello:

This series was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:

Quoted 9 lines · On Wed, 9 Jul 2025 13:09:36 +0200 you wrote:

From: Frank Wunderlich <[email protected]>

This series continues mt7988 devicetree work

- Extend cpu frequency scaling with CCI
- GPIO leds
- Basic network-support (ethernet controller + builtin switch + SFP Cages)

[...]

Here is the summary with links:
- [v9,01/13] dt-bindings: net: mediatek,net: update mac subnode pattern for mt7988
https://git.kernel.org/netdev/net-next/c/29712b437339
- [v9,02/13] dt-bindings: net: mediatek,net: allow up to 8 IRQs
https://git.kernel.org/netdev/net-next/c/356dea0baf4c
- [v9,03/13] dt-bindings: net: mediatek,net: allow irq names
https://git.kernel.org/netdev/net-next/c/23ac2a71bdbd
- [v9,04/13] dt-bindings: net: mediatek,net: add sram property
https://git.kernel.org/netdev/net-next/c/c4582a31efd9
- [v9,05/13] dt-bindings: net: dsa: mediatek,mt7530: add dsa-port definition for mt7988
https://git.kernel.org/netdev/net-next/c/588cb646ce70
- [v9,06/13] dt-bindings: net: dsa: mediatek,mt7530: add internal mdio bus
https://git.kernel.org/netdev/net-next/c/66a44adf4c3d
- [v9,07/13] arm64: dts: mediatek: mt7986: add sram node
(no matching commit)
- [v9,08/13] arm64: dts: mediatek: mt7986: add interrupts for RSS and interrupt names (no matching commit)
- [v9,09/13] arm64: dts: mediatek: mt7988: add basic ethernet-nodes
(no matching commit)
- [v9,10/13] arm64: dts: mediatek: mt7988: add switch node
(no matching commit)
- [v9,11/13] arm64: dts: mediatek: mt7988a-bpi-r4: add aliases for ethernet (no matching commit)
- [v9,12/13] arm64: dts: mediatek: mt7988a-bpi-r4: add sfp cages and link to gmac (no matching commit)
- [v9,13/13] arm64: dts: mediatek: mt7988a-bpi-r4: configure switch phys and leds (no matching commit)

Quoted 1 line

You are awesome, thank you!

Hi

Any comments on the missing DTS parts or can they applied too? regards Frank

maintainer
#19 lore raw
Quoted 1 line · On Sat, 16 Aug 2025 08:55:51 +0200 Frank Wunderlich wrote:

Any comments on the missing DTS parts or can they applied too?

You should probably put the maintainers you're addressing this question to in the To: header of the email.

#20 lore raw
In reply to Frank Wunderlich

Am 16. August 2025 08:55:51 MESZ schrieb Frank Wunderlich <[email protected]>:

Quoted 45 lines

Am 11. Juli 2025 00:10:22 MESZ schrieb [email protected]:

Quoted 44 lines

Hello:

This series was applied to netdev/net-next.git (main) by Jakub Kicinski <[email protected]>:

Quoted 9 lines · On Wed, 9 Jul 2025 13:09:36 +0200 you wrote:

From: Frank Wunderlich <[email protected]>

This series continues mt7988 devicetree work

- Extend cpu frequency scaling with CCI
- GPIO leds
- Basic network-support (ethernet controller + builtin switch + SFP Cages)

[...]

Here is the summary with links:
- [v9,01/13] dt-bindings: net: mediatek,net: update mac subnode pattern for mt7988
https://git.kernel.org/netdev/net-next/c/29712b437339
- [v9,02/13] dt-bindings: net: mediatek,net: allow up to 8 IRQs
https://git.kernel.org/netdev/net-next/c/356dea0baf4c
- [v9,03/13] dt-bindings: net: mediatek,net: allow irq names
https://git.kernel.org/netdev/net-next/c/23ac2a71bdbd
- [v9,04/13] dt-bindings: net: mediatek,net: add sram property
https://git.kernel.org/netdev/net-next/c/c4582a31efd9
- [v9,05/13] dt-bindings: net: dsa: mediatek,mt7530: add dsa-port definition for mt7988
https://git.kernel.org/netdev/net-next/c/588cb646ce70
- [v9,06/13] dt-bindings: net: dsa: mediatek,mt7530: add internal mdio bus
https://git.kernel.org/netdev/net-next/c/66a44adf4c3d
- [v9,07/13] arm64: dts: mediatek: mt7986: add sram node
(no matching commit)
- [v9,08/13] arm64: dts: mediatek: mt7986: add interrupts for RSS and interrupt names (no matching commit)
- [v9,09/13] arm64: dts: mediatek: mt7988: add basic ethernet-nodes
(no matching commit)
- [v9,10/13] arm64: dts: mediatek: mt7988: add switch node
(no matching commit)
- [v9,11/13] arm64: dts: mediatek: mt7988a-bpi-r4: add aliases for ethernet (no matching commit)
- [v9,12/13] arm64: dts: mediatek: mt7988a-bpi-r4: add sfp cages and link to gmac (no matching commit)
- [v9,13/13] arm64: dts: mediatek: mt7988a-bpi-r4: configure switch phys and leds (no matching commit)

Quoted 6 lines
Quoted 1 line

You are awesome, thank you!

Hi

Any comments on the missing DTS parts or can they applied too? regards Frank

Hi

Moved mtk maintainers in TO header.
regards Frank

maintainer
#21 lore raw
In reply to Frank Wunderlich

Queued patches 7 - 13

Thanks!

Quoted 136 lines · Frank Wunderlich

From: Frank Wunderlich <[email protected]>

This series continues mt7988 devicetree work

- Extend cpu frequency scaling with CCI
- GPIO leds
- Basic network-support (ethernet controller + builtin switch + SFP Cages)

depencies (i hope this list is complete and latest patches/series linked):

support interrupt-names is optional again as i re-added the reserved IRQs (they are not unusable as i thought and can allow features in future)
https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/

needs change in mtk ethernet driver for the sram to be read from separate node:
https://patchwork.kernel.org/project/netdevbpf/patch/c2b9242229d06af4e468204bcf42daa1535c3a72.1751461762.git.daniel@makrotopia.org/

for SFP-Function (macs currently disabled):

PCS clearance which is a 1.5 year discussion currently ongoing

Daniel asked netdev for a way 2 go:
https://lore.kernel.org/netdev/[email protected]/

e.g. something like this (one of):
* https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/ (v6)
* https://patchwork.kernel.org/project/netdevbpf/patch/[email protected]/ (v4)
* https://patchwork.kernel.org/project/netdevbpf/patch/ba4e359584a6b3bc4b3470822c42186d5b0856f9.1721910728.git.daniel@makrotopia.org/

full usxgmii driver:
https://patchwork.kernel.org/project/netdevbpf/patch/07845ec900ba41ff992875dce12c622277592c32.1702352117.git.daniel@makrotopia.org/

first PCS-discussion is here:
https://patchwork.kernel.org/project/netdevbpf/patch/8aa905080bdb6760875d62cb3b2b41258837f80e.1702352117.git.daniel@makrotopia.org/
some more here:
https://lore.kernel.org/netdev/[email protected]/

and then dts nodes for sgmiisys+usxgmii+2g5 firmware

when above depencies are solved the mac1/2 can be enabled and 2.5G phy/SFP slots will work.

changes:
v9:
- dropped patches already applied (cci,gpio-leds,unused pins)
- added patches to add RSS IRQs, IRQ-names and sram-node for mt7986
note: mt7981 does not have a ethernet node yet
- set minItems for Filogic (MT798x) IRQs/Names to 8 needed to update MT7986 binding example because of this
- add sram:false to non-Filogic SoCs

v8:
- splitted binding into irq-count and irq-names and updated description
- fixed typo in mt7621 section "interrupt-namess"
- splitted binding changes into fixes (mac) and additions (sram)
- dropped change of reg (simple count to description)
- change ethernet register size to 0x40000

v7:
- fixed rebasing error while splitting dt-binding patch

v6:
binding:
- split out the interrupt-names into separate patch
- update irq(name) min count to 4
- move interrupt-names up
- add sram-property
- drop second reg entry and minitems as there is only 1 item left

dts:
- fix whitespace-errors for pdma irqs (spaces vs. tabs)
- move sram from eth reg to own sram node (needs CONFIG_SRAM)

v5:
- add reserved irqs and change names
- update binding for 8 irqs with different names (rx,tx => fe1+fe2, rx-ringX => pdmaX) (dropped Robs RB due to this change again, sorry)

v4:
net-binding:
- allow interrupt names and increase max interrupts to 6 because of RSS/LRO interrupts (dropped Robs RB due to this change)

dts-patches:
- add interrupts for RSS/LRO and interrupt-names for ethernet node
- eth-reg and clock whitespace-fix
- comment for fixed-link on gmac0
- drop phy-mode properties as suggested by andrew
- drop phy-connection-type on 2g5 board
- reorder some properties
- update 2g5 phy node
- unit-name dec instead of hex to match reg property
- move compatible before reg
- drop phy-mode

v3:
- dropped patches already applied (SPI+thermal)
- added soc specific cci compatible (new binding patch + changed dts)
- enable 2g5 phy because driver is now merged
- add patch for cleaning up unnecessary pins
- add patch for gpio-leds
- add patch for adding ethernet aliases

v2:
- change reg to list of items in eth binding
- changed mt7530 binding:
- unevaluatedProperties=false
- mediatek,pio subproperty
- from patternProperty to property
- board specific properties like led function and labels moved to bpi-r4 dtsi

Frank Wunderlich (13):
dt-bindings: net: mediatek,net: update mac subnode pattern for mt7988
dt-bindings: net: mediatek,net: allow up to 8 IRQs
dt-bindings: net: mediatek,net: allow irq names
dt-bindings: net: mediatek,net: add sram property
dt-bindings: net: dsa: mediatek,mt7530: add dsa-port definition for

     mt7988

dt-bindings: net: dsa: mediatek,mt7530: add internal mdio bus
arm64: dts: mediatek: mt7986: add sram node
arm64: dts: mediatek: mt7986: add interrupts for RSS and interrupt
names
arm64: dts: mediatek: mt7988: add basic ethernet-nodes
arm64: dts: mediatek: mt7988: add switch node
arm64: dts: mediatek: mt7988a-bpi-r4: add aliases for ethernet
arm64: dts: mediatek: mt7988a-bpi-r4: add sfp cages and link to gmac
arm64: dts: mediatek: mt7988a-bpi-r4: configure switch phys and leds

  .../bindings/net/dsa/mediatek,mt7530.yaml     |  24 +-
  .../devicetree/bindings/net/mediatek,net.yaml |  64 +++-
  arch/arm64/boot/dts/mediatek/mt7986a.dtsi     |  20 +-
  .../mediatek/mt7988a-bananapi-bpi-r4-2g5.dts  |  11 +
  .../dts/mediatek/mt7988a-bananapi-bpi-r4.dts  |  19 ++
  .../dts/mediatek/mt7988a-bananapi-bpi-r4.dtsi |  86 ++++++
  arch/arm64/boot/dts/mediatek/mt7988a.dtsi     | 285 +++++++++++++++++-
  7 files changed, 497 insertions(+), 12 deletions(-)