dt-bindings: PCI: Convert axis,artpec6-pcie to DT schema
Subsystems (4)
Rob Herring (Arm)
maintainerPATCH 1/1 dt-bindings: PCI: Convert axis,artpec6-pcie to DT schema
Convert the Axis ARTPEC-6/7 PCIe binding to DT schema format. It's a straight forward conversion.
Signed-off-by Rob Herring (Arm) <[email protected]>
--- .../bindings/pci/axis,artpec6-pcie.txt | 50 -------- .../bindings/pci/axis,artpec6-pcie.yaml | 118 ++++++++++++++++++ 2 files changed, 118 insertions(+), 50 deletions(-) delete mode 100644 Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt create mode 100644 Documentation/devicetree/bindings/pci/axis,artpec6-pcie.yaml
Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt deleted +0 -50
@@ -1,50 +0,0 @@ -* Axis ARTPEC-6 PCIe interface - -This PCIe host controller is based on the Synopsys DesignWare PCIe IP -and thus inherits all the common properties defined in snps,dw-pcie.yaml. - -Required properties: -- compatible: "axis,artpec6-pcie", "snps,dw-pcie" for ARTPEC-6 in RC mode; - "axis,artpec6-pcie-ep", "snps,dw-pcie" for ARTPEC-6 in EP mode; - "axis,artpec7-pcie", "snps,dw-pcie" for ARTPEC-7 in RC mode; - "axis,artpec7-pcie-ep", "snps,dw-pcie" for ARTPEC-7 in EP mode; -- reg: base addresses and lengths of the PCIe controller (DBI), - the PHY controller, and configuration address space. -- reg-names: Must include the following entries: - - "dbi" - - "phy" - - "config" -- interrupts: A list of interrupt outputs of the controller. Must contain an - entry for each entry in the interrupt-names property. -- interrupt-names: Must include the following entries: - - "msi": The interrupt that is asserted when an MSI is received -- axis,syscon-pcie: A phandle pointing to the ARTPEC-6 system controller, - used to enable and control the Synopsys IP. - -Example: - - pcie@f8050000 { - compatible = "axis,artpec6-pcie", "snps,dw-pcie"; - reg = <0xf8050000 0x2000 - 0xf8040000 0x1000 - 0xc0000000 0x2000>; - reg-names = "dbi", "phy", "config"; - #address-cells = <3>; - #size-cells = <2>; - device_type = "pci"; - /* downstream I/O */ - ranges = <0x81000000 0 0 0xc0002000 0 0x00010000 - /* non-prefetchable memory */ - 0x82000000 0 0xc0012000 0xc0012000 0 0x1ffee000>; - num-lanes = <2>; - bus-range = <0x00 0xff>; - interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "msi"; - #interrupt-cells = <1>; - interrupt-map-mask = <0 0 0 0x7>; - interrupt-map = <0 0 0 1 &intc GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>, - <0 0 0 2 &intc GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>, - <0 0 0 3 &intc GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>, - <0 0 0 4 &intc GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>; - axis,syscon-pcie = <&syscon>; - };
Documentation/devicetree/bindings/pci/axis,artpec6-pcie.yaml new file +118 -0
118 lines not on this page · raw message
Signature · 1 line
2.47.2
Manivannan Sadhasivam
AppliedQuoted 4 lines · Rob Herring (Arm)
Convert the Axis ARTPEC-6/7 PCIe binding to DT schema format. It's a straight forward conversion.
Applied, thanks!
[1/1] dt-bindings: PCI: Convert axis,artpec6-pcie to DT schema
commit: bfde613ae16ec592e2aa28ad7f7729bc20b9382c
Best regards,
Signature · 1 line
Manivannan Sadhasivam <[email protected]>