Skip to contentSkip to conversation

dt-bindings: PCI: Convert axis,artpec6-pcie to DT schema

PATCH Applied Rob Herring (Arm) 2 participants 2 messages Jul 10, 2025 – Jul 17, 2025

Subsystems (4)
lore
Share & tools
lore

Rob Herring (Arm)

author maintainer
#0 lore raw

PATCH 1/1 dt-bindings: PCI: Convert axis,artpec6-pcie to DT schema

Convert the Axis ARTPEC-6/7 PCIe binding to DT schema format. It's a straight forward conversion.

---
 .../bindings/pci/axis,artpec6-pcie.txt        |  50 --------
 .../bindings/pci/axis,artpec6-pcie.yaml       | 118 ++++++++++++++++++
 2 files changed, 118 insertions(+), 50 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt
 create mode 100644 Documentation/devicetree/bindings/pci/axis,artpec6-pcie.yaml
Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt deleted +0 -50
deleted file mode 100644
index cc6dcdb676b9..000000000000
@@ -1,50 +0,0 @@
-* Axis ARTPEC-6 PCIe interface
-
-This PCIe host controller is based on the Synopsys DesignWare PCIe IP
-and thus inherits all the common properties defined in snps,dw-pcie.yaml.
-
-Required properties:
-- compatible: "axis,artpec6-pcie", "snps,dw-pcie" for ARTPEC-6 in RC mode;
-	      "axis,artpec6-pcie-ep", "snps,dw-pcie" for ARTPEC-6 in EP mode;
-	      "axis,artpec7-pcie", "snps,dw-pcie" for ARTPEC-7 in RC mode;
-	      "axis,artpec7-pcie-ep", "snps,dw-pcie" for ARTPEC-7 in EP mode;
-- reg: base addresses and lengths of the PCIe controller (DBI),
-	the PHY controller, and configuration address space.
-- reg-names: Must include the following entries:
-	- "dbi"
-	- "phy"
-	- "config"
-- interrupts: A list of interrupt outputs of the controller. Must contain an
-  entry for each entry in the interrupt-names property.
-- interrupt-names: Must include the following entries:
-	- "msi": The interrupt that is asserted when an MSI is received
-- axis,syscon-pcie: A phandle pointing to the ARTPEC-6 system controller,
-	used to enable and control the Synopsys IP.
-
-Example:
-
-	pcie@f8050000 {
-		compatible = "axis,artpec6-pcie", "snps,dw-pcie";
-		reg = <0xf8050000 0x2000
-		       0xf8040000 0x1000
-		       0xc0000000 0x2000>;
-		reg-names = "dbi", "phy", "config";
-		#address-cells = <3>;
-		#size-cells = <2>;
-		device_type = "pci";
-			  /* downstream I/O */
-		ranges = <0x81000000 0 0 0xc0002000 0 0x00010000
-			  /* non-prefetchable memory */
-			  0x82000000 0 0xc0012000 0xc0012000 0 0x1ffee000>;
-		num-lanes = <2>;
-		bus-range = <0x00 0xff>;
-		interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "msi";
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0x7>;
-		interrupt-map = <0 0 0 1 &intc GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
-		                <0 0 0 2 &intc GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
-		                <0 0 0 3 &intc GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
-		                <0 0 0 4 &intc GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
-		axis,syscon-pcie = <&syscon>;
-	};
Documentation/devicetree/bindings/pci/axis,artpec6-pcie.yaml new file +118 -0

118 lines not on this page · raw message

Signature · 1 line
2.47.2
#1 lore raw
Quoted 4 lines · Rob Herring (Arm)

Convert the Axis ARTPEC-6/7 PCIe binding to DT schema format. It's a straight forward conversion.

Applied, thanks!

[1/1] dt-bindings: PCI: Convert axis,artpec6-pcie to DT schema

      commit: bfde613ae16ec592e2aa28ad7f7729bc20b9382c

Best regards,

Signature · 1 line
Manivannan Sadhasivam <[email protected]>