Use correct LDO5 control registers for PCA9450
cover Use correct LDO5 control registers for PCA9450
From: Frieder Schrempf <[email protected]>
This is a port for the following series in Linux, which is already available in mainline:
https://patchwork.kernel.org/project/linux-arm-kernel/cover/[email protected]/
This aligns the PMIC driver with current Linux and allows to use upstream devicetrees in U-Boot.
Frieder Schrempf (6):
Revert "pmic: pca9450: Add optional SD_VSEL GPIO for LDO5"
pmic: pca9450: Fix enable register for LDO5
pmic: pca9450: Fix control register for LDO5
pmic: pca9450: Handle hardware with fixed SD_VSEL for LDO5
arm: dts: imx8mp-data-modul-edm-sbc: Remove deprecated sd-vsel-gpios
arm: dts: imx8mp-dhcom-som: Remove deprecated sd-vsel-gpios
arch/arm/dts/imx8mp-data-modul-edm-sbc.dts | 1 - arch/arm/dts/imx8mp-dhcom-som.dtsi | 1 - drivers/power/pmic/pca9450.c | 22 ------------- drivers/power/regulator/pca9450.c | 37 ++++++++++++++++++++-- 4 files changed, 34 insertions(+), 27 deletions(-)
Signature · 1 line
2.50.1
PATCH 1/6 Revert "pmic: pca9450: Add optional SD_VSEL GPIO for LDO5"
From: Frieder Schrempf <[email protected]>
This reverts commit 2add0511757e2c5897a88b57c5ea8c912140e60f.
It turns out that all boards using the PCA9450 actually have the SD_VSEL input connected to the VSELECT signal of the SoCs SD/MMC interface. Therefore we don't need manual control for this signal via GPIO and there aren't any users.
This is equivalent to the following change in Linux:
c73be62caabb ("Revert "regulator: pca9450: Add SD_VSEL GPIO for LDO5"")
--- drivers/power/pmic/pca9450.c | 22 ---------------------- 1 file changed, 22 deletions(-)
drivers/power/pmic/pca9450.c +0 -22
@@ -6,12 +6,9 @@#include <fdtdec.h> #include <errno.h> #include <dm.h> -#include <dm/device_compat.h> #include <i2c.h> -#include <linux/err.h> #include <log.h> #include <asm/global_data.h> -#include <asm-generic/gpio.h> #include <linux/printk.h> #include <power/pmic.h> #include <power/regulator.h>
@@ -29,10 +26,6 @@ static const struct pmic_child_info pmic_children_info[] = { { }, }; -struct pca9450_priv { -struct gpio_desc *sd_vsel_gpio; -}; -static int pca9450_reg_count (struct udevice *dev) {return PCA9450_REG_NUM ;
@@ -85,21 +78,7 @@ static int pca9450_bind(struct udevice *dev)static int pca9450_probe (struct udevice *dev) { -struct pca9450_priv *priv =dev_get_priv (dev);unsigned int reset_ctrl; -int ret =0 ; - -if (CONFIG_IS_ENABLED (DM_GPIO ) &&CONFIG_IS_ENABLED (DM_REGULATOR_PCA9450 )) { - priv->sd_vsel_gpio =devm_gpiod_get_optional (dev,"sd-vsel" , -GPIOD_IS_OUT | -GPIOD_IS_OUT_ACTIVE ); -if (IS_ERR (priv->sd_vsel_gpio)) { - ret =PTR_ERR (priv->sd_vsel_gpio); -dev_err (dev,"Failed to request SD_VSEL GPIO: %d\n" , ret); -if (ret) -return ret; - } - }if (ofnode_read_bool (dev_ofnode (dev),"nxp,wdog_b-warm-reset" )) reset_ctrl =PCA9450_PMIC_RESET_WDOG_B_CFG_WARM ;
@@ -132,5 +111,4 @@ U_BOOT_DRIVER(pmic_pca9450) = { .bind = pca9450_bind, .probe = pca9450_probe, .ops = &pca9450_ops, - .priv_auto = sizeof(struct pca9450_priv), };
Signature · 1 line
2.50.1
PATCH 2/6 pmic: pca9450: Fix enable register for LDO5
In reply to Frieder SchrempfFrom: Frieder Schrempf <[email protected]>
The LDO5 regulator has two configuration registers, but only LDO5CTRL_L contains the bits for enabling/disabling the regulator.
This is equivalent to the following change in Linux:
f5aab0438ef1 ("regulator: pca9450: Fix enable register for LDO5")
--- drivers/power/regulator/pca9450.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/power/regulator/pca9450.c +1 -1
@@ -144,7 +144,7 @@ static struct pca9450_plat pca9450_reg_data[] = {PCA_DATA ("LDO4" ,PCA9450_LDO4CTRL ,HW_STATE_CONTROL ,PCA9450_LDO4CTRL ,PCA9450_LDO34_MASK , pca9450_ldo34_vranges), -PCA_DATA ("LDO5" ,PCA9450_LDO5CTRL_H ,HW_STATE_CONTROL , +PCA_DATA ("LDO5" ,PCA9450_LDO5CTRL_L ,HW_STATE_CONTROL ,PCA9450_LDO5CTRL_H ,PCA9450_LDO5_MASK , pca9450_ldo5_vranges), };
Signature · 1 line
2.50.1
PATCH 3/6 pmic: pca9450: Fix control register for LDO5
In reply to Frieder SchrempfFrom: Frieder Schrempf <[email protected]>
For LDO5 we need to be able to check the status of the SD_VSEL input in order to know which control register is used. Read the status of the SD_VSEL signal via GPIO and use the correct register accordingly.
To use this, the LDO5 node in the devicetree needs the sd-vsel-gpios property to reference the GPIO that is used to read back the SD_VSEL status internally. Please note that the SION bit in the IOMUX must be set if the signal is muxed as VSELECT and controlled by the USDHC controller.
This is equivalent to the following change in Linux:
3ce6f4f943dd ("regulator: pca9450: Fix control register for LDO5")
--- drivers/power/regulator/pca9450.c | 31 +++++++++++++++++++++++++++++-- 1 file changed, 29 insertions(+), 2 deletions(-)
drivers/power/regulator/pca9450.c +29 -2
@@ -7,9 +7,12 @@* ROHM BD71837 regulator driver */ +#include <asm-generic/gpio.h> #include <dm.h> +#include <dm/device_compat.h> #include <log.h> #include <linux/bitops.h> +#include <linux/err.h> #include <power/pca9450.h> #include <power/pmic.h> #include <power/regulator.h>
@@ -52,6 +55,7 @@ struct pca9450_plat {u8 volt_mask;struct pca9450_vrange *ranges;unsigned int numranges; +struct gpio_desc *sd_vsel_gpio; };#define PCA_RANGE (_min, _vstep, _sel_low, _sel_hi) \
@@ -222,13 +226,23 @@ static int pca9450_set_enable(struct udevice *dev, bool enable) val); } +static u8 pca9450_get_vsel_reg (struct pca9450_plat *plat) +{ +if (!strcmp (plat->name,"LDO5" ) && + (plat->sd_vsel_gpio && !dm_gpio_get_value(plat->sd_vsel_gpio)) { +return PCA9450_LDO5CTRL_L ; + } + +return plat->volt_reg; +} +static int pca9450_get_value (struct udevice *dev) {struct pca9450_plat *plat =dev_get_plat (dev);unsigned int reg, tmp;int i, ret; - ret =pmic_reg_read (dev->parent, plat->volt_reg); + ret =pmic_reg_read (dev->parent,pca9450_get_vsel_reg (plat));if (ret <0 )return ret;
@@ -274,7 +288,7 @@ static int pca9450_set_value(struct udevice *dev, int uvolt)if (!found)return -EINVAL ; -return pmic_clrsetbits (dev->parent, plat->volt_reg, +return pmic_clrsetbits (dev->parent,pca9450_get_vsel_reg (plat), plat->volt_mask, sel); }
@@ -335,6 +349,19 @@ static int pca9450_regulator_probe(struct udevice *dev) *plat = pca9450_reg_data[i]; +if (!strcmp (plat->name,"LDO5" )) { +if (CONFIG_IS_ENABLED (DM_GPIO ) &&CONFIG_IS_ENABLED (DM_REGULATOR_PCA9450 )) { + plat->sd_vsel_gpio =devm_gpiod_get_optional (dev,"sd-vsel" , +GPIOD_IS_IN ); +if (IS_ERR (plat->sd_vsel_gpio)) { + ret =PTR_ERR (plat->sd_vsel_gpio); +dev_err (dev,"Failed to request SD_VSEL GPIO: %d\n" , ret); +if (ret) +return ret; + } + } + } +return 0 ; }
Signature · 1 line
2.50.1
PATCH 4/6 pmic: pca9450: Handle hardware with fixed SD_VSEL for LDO5
In reply to Frieder SchrempfFrom: Frieder Schrempf <[email protected]>
There are two ways to set the output voltage of the LD05 regulator. First by writing to the voltage selection registers and second by toggling the SD_VSEL signal.
Usually board designers connect SD_VSEL to the VSELECT signal controlled by the USDHC controller, but in some cases the signal is hardwired to a fixed low level (therefore selecting 3.3V as initial value for allowing to boot from the SD card).
In these cases, the voltage is only determined by the value of the LDO5CTRL_L register. Introduce a property nxp,sd-vsel-fixed-low to let the driver know that SD_VSEL is low and there is no GPIO to actually get that information from dynamically.
This is equivalent to the following change in Linux:
c8c1ab2c5cb7 ("regulator: pca9450: Handle hardware with fixed SD_VSEL for LDO5")
--- drivers/power/regulator/pca9450.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/power/regulator/pca9450.c +5 -1
@@ -56,6 +56,7 @@ struct pca9450_plat {struct pca9450_vrange *ranges;unsigned int numranges;struct gpio_desc *sd_vsel_gpio; +bool sd_vsel_fixed_low; };#define PCA_RANGE (_min, _vstep, _sel_low, _sel_hi) \
@@ -229,7 +230,8 @@ static int pca9450_set_enable(struct udevice *dev, bool enable)static u8 pca9450_get_vsel_reg (struct pca9450_plat *plat) {if (!strcmp (plat->name,"LDO5" ) && - (plat->sd_vsel_gpio && !dm_gpio_get_value(plat->sd_vsel_gpio)) { + ((plat->sd_vsel_gpio && !dm_gpio_get_value (plat->sd_vsel_gpio)) || + plat->sd_vsel_fixed_low)) {return PCA9450_LDO5CTRL_L ; }
@@ -360,6 +362,8 @@ static int pca9450_regulator_probe(struct udevice *dev)return ret; } } + + plat->sd_vsel_fixed_low =dev_read_bool (dev,"nxp,sd-vsel-fixed-low" ); }return 0 ;
Signature · 1 line
2.50.1
PATCH 5/6 arm: dts: imx8mp-data-modul-edm-sbc: Remove deprecated sd-vsel-gpios
In reply to Frieder SchrempfFrom: Frieder Schrempf <[email protected]>
The sd-vsel-gpios property in the root of the PMIC node is deprecated and therefore not parsed by the driver anymore. We can safely remove this as it wasn't used anyway due to the pad not having the correct pinmux settings.
--- arch/arm/dts/imx8mp-data-modul-edm-sbc.dts | 1 - 1 file changed, 1 deletion(-)
arch/arm/dts/imx8mp-data-modul-edm-sbc.dts +0 -1
@@ -344,7 +344,6 @@ pinctrl-0 = <&pinctrl_pmic>; interrupt-parent = <&gpio1>; interrupts = <3 IRQ_TYPE_LEVEL_LOW>; - sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; /* * i.MX 8M Plus Data Sheet for Consumer Products
Signature · 1 line
2.50.1
Re: [PATCH 5/6] arm: dts: imx8mp-data-modul-edm-sbc: Remove deprecated sd-vsel-gpios
Quoted 8 lines · Frieder Schrempf
From: Frieder Schrempf <[email protected]>
The sd-vsel-gpios property in the root of the PMIC node is deprecated and therefore not parsed by the driver anymore. We can safely remove this as it wasn't used anyway due to the pad not having the correct pinmux settings.
Signed-off-by Frieder Schrempf <[email protected]>
PATCH 6/6 arm: dts: imx8mp-dhcom-som: Remove deprecated sd-vsel-gpios
In reply to Frieder SchrempfFrom: Frieder Schrempf <[email protected]>
The sd-vsel-gpios property in the root of the PMIC node is deprecated and therefore not parsed by the driver anymore. We can safely remove this as it wasn't used anyway due to the pad not having the correct pinmux settings.
--- arch/arm/dts/imx8mp-dhcom-som.dtsi | 1 - 1 file changed, 1 deletion(-)
arch/arm/dts/imx8mp-dhcom-som.dtsi +0 -1
@@ -245,7 +245,6 @@ pinctrl-0 = <&pinctrl_pmic>; interrupt-parent = <&gpio1>; interrupts = <3 IRQ_TYPE_LEVEL_LOW>; - sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; /* * i.MX 8M Plus Data Sheet for Consumer Products
Signature · 1 line
2.50.1
Re: [PATCH 6/6] arm: dts: imx8mp-dhcom-som: Remove deprecated sd-vsel-gpios
Quoted 8 lines · Frieder Schrempf
From: Frieder Schrempf <[email protected]>
The sd-vsel-gpios property in the root of the PMIC node is deprecated and therefore not parsed by the driver anymore. We can safely remove this as it wasn't used anyway due to the pad not having the correct pinmux settings.
Signed-off-by Frieder Schrempf <[email protected]>
I'll eventually finish switch of two leftover boards to OF_UPSTREAM and drop this whole file, thanks for the reminder.
Hi Jaehoon,
Am 11.08.25 um 15:11 schrieb Frieder Schrempf:
Quoted 18 lines
From: Frieder Schrempf <[email protected]>
This is a port for the following series in Linux, which is already available in mainline:
https://patchwork.kernel.org/project/linux-arm-kernel/cover/[email protected]/
This aligns the PMIC driver with current Linux and allows to use upstream devicetrees in U-Boot.
Frieder Schrempf (6):
Revert "pmic: pca9450: Add optionalSD_VSELGPIO for LDO5"
pmic: pca9450: Fix enable register for LDO5
pmic: pca9450: Fix control register for LDO5
pmic: pca9450: Handle hardware with fixedSD_VSELfor LDO5
arm: dts: imx8mp-data-modul-edm-sbc: Remove deprecated sd-vsel-gpios
arm: dts: imx8mp-dhcom-som: Remove deprecated sd-vsel-gpios
Quoted 6 lines
arch/arm/dts/imx8mp-data-modul-edm-sbc.dts | 1 - arch/arm/dts/imx8mp-dhcom-som.dtsi | 1 - drivers/power/pmic/pca9450.c | 22 ------------- drivers/power/regulator/pca9450.c | 37 ++++++++++++++++++++-- 4 files changed, 34 insertions(+), 27 deletions(-)
I saw that there are several patches on the mailing list for /drivers/power that have received no reply from a maintainer for several weeks (see [1]). I just wanted to make sure that you are aware of this and kindly ask to have a look.
Thanks
Frieder
Quoted 49 lines
Subject: Re: [PATCH 0/6] Use correct LDO5 control registers for PCA9450
Hi Jaehoon,
Am 11.08.25 um 15:11 schrieb Frieder Schrempf:
Quoted 6 lines
From: Frieder Schrempf <[email protected]>
This is a port for the following series in Linux, which is already available in mainline:
https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2F
patcQuoted 1 line
hwork.kernel.org%2Fproject%2Flinux-arm-
kernel%2Fcover%2F20241218152842
Quoted 1 line
.97483-1-
frieder%40fris.de%2F&data=05%7C02%7Cpeng.fan%40nxp.com%7C51 6d
Quoted 1 line
65c0706c4d71292d08dde3b31d9d%7C686ea1d3bc2b4c6fa92cd99c5c 301635%7C0%7C
Quoted 1 line
0%7C638917080648452454%7CUnknown%7CTWFpbGZsb3d8eyJFbXB 0eU1hcGkiOnRydWU
Quoted 1 line
sIlYiOiIwLjAuMDAwMCIsIlAiOiJXaW4zMiIsIkFOIjoiTWFpbCIsIldUIjoyfQ% 3D%3D%
Quoted 1 line
7C0%7C%7C%7C&sdata=neJx6WZU4iZWjSUcsnzOVQvFiaCTKLChE8srEx 6cwEQ%3D&rese
Quoted 11 lines
rved=0
This aligns the PMIC driver with current Linux and allows to use upstream devicetrees in U-Boot.
Frieder Schrempf (6):
Revert "pmic: pca9450: Add optionalSD_VSELGPIO for LDO5"
pmic: pca9450: Fix enable register for LDO5
pmic: pca9450: Fix control register for LDO5
pmic: pca9450: Handle hardware with fixedSD_VSELfor LDO5
arm: dts: imx8mp-data-modul-edm-sbc: Remove deprecated sd-vsel-gpios
Quoted 6 lines
arm: dts: imx8mp-dhcom-som: Remove deprecated sd-vsel-gpios
arch/arm/dts/imx8mp-data-modul-edm-sbc.dts | 1 - arch/arm/dts/imx8mp-dhcom-som.dtsi | 1 - drivers/power/pmic/pca9450.c | 22 ------------- drivers/power/regulator/pca9450.c | 37
Quoted 8 lines
++++++++++++++++++++--
Quoted 2 lines
4 files changed, 34 insertions(+), 27 deletions(-)I saw that there are several patches on the mailing list for /drivers/power that have received no reply from a maintainer for several weeks (see [1]). I just wanted to make sure that you are aware of this and kindly ask to have a look.
I could help handle that via mmc tree, if Tom and you are ok.
Regards
Peng.
Quoted 5 lines
Thanks
Frieder[1]
Am 27.08.25 um 07:46 schrieb Peng Fan:
Quoted 53 lines
Quoted 53 lines
Subject: Re: [PATCH 0/6] Use correct LDO5 control registers for PCA9450
Hi Jaehoon,
Am 11.08.25 um 15:11 schrieb Frieder Schrempf:
Quoted 6 lines
From: Frieder Schrempf <[email protected]>
This is a port for the following series in Linux, which is already available in mainline:
https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2F
patcQuoted 1 line
hwork.kernel.org%2Fproject%2Flinux-arm-
kernel%2Fcover%2F20241218152842
Quoted 1 line
.97483-1-
frieder%40fris.de%2F&data=05%7C02%7Cpeng.fan%40nxp.com%7C51 6d
Quoted 1 line
65c0706c4d71292d08dde3b31d9d%7C686ea1d3bc2b4c6fa92cd99c5c 301635%7C0%7C
Quoted 1 line
0%7C638917080648452454%7CUnknown%7CTWFpbGZsb3d8eyJFbXB 0eU1hcGkiOnRydWU
Quoted 1 line
sIlYiOiIwLjAuMDAwMCIsIlAiOiJXaW4zMiIsIkFOIjoiTWFpbCIsIldUIjoyfQ% 3D%3D%
Quoted 1 line
7C0%7C%7C%7C&sdata=neJx6WZU4iZWjSUcsnzOVQvFiaCTKLChE8srEx 6cwEQ%3D&rese
Quoted 11 lines
rved=0
This aligns the PMIC driver with current Linux and allows to use upstream devicetrees in U-Boot.
Frieder Schrempf (6):
Revert "pmic: pca9450: Add optionalSD_VSELGPIO for LDO5"
pmic: pca9450: Fix enable register for LDO5
pmic: pca9450: Fix control register for LDO5
pmic: pca9450: Handle hardware with fixedSD_VSELfor LDO5
arm: dts: imx8mp-data-modul-edm-sbc: Remove deprecated sd-vsel-gpios
Quoted 6 lines
arm: dts: imx8mp-dhcom-som: Remove deprecated sd-vsel-gpios
arch/arm/dts/imx8mp-data-modul-edm-sbc.dts | 1 - arch/arm/dts/imx8mp-dhcom-som.dtsi | 1 - drivers/power/pmic/pca9450.c | 22 ------------- drivers/power/regulator/pca9450.c | 37++++++++++++++++++++--
Quoted 2 lines
4 files changed, 34 insertions(+), 27 deletions(-)
Quoted 6 lines
Quoted 4 lines
I saw that there are several patches on the mailing list for /drivers/power that have received no reply from a maintainer for several weeks (see [1]). I just wanted to make sure that you are aware of this and kindly ask to have a look.
I could help handle that via mmc tree, if Tom and you are ok.
I don't mind. If Tom agrees to take power patches through the mmc tree from you that's fine.
Quoted 59 lines · Frieder Schrempf
Am 27.08.25 um 07:46 schrieb Peng Fan:
Quoted 58 lines
Quoted 57 lines
Subject: Re: [PATCH 0/6] Use correct LDO5 control registers for PCA9450
Hi Jaehoon,
Am 11.08.25 um 15:11 schrieb Frieder Schrempf:
Quoted 6 lines
From: Frieder Schrempf <[email protected]>
This is a port for the following series in Linux, which is already available in mainline:
https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2F
patcQuoted 1 line
hwork.kernel.org%2Fproject%2Flinux-arm-
kernel%2Fcover%2F20241218152842
Quoted 1 line
.97483-1-
frieder%40fris.de%2F&data=05%7C02%7Cpeng.fan%40nxp.com%7C51 6d
Quoted 1 line
65c0706c4d71292d08dde3b31d9d%7C686ea1d3bc2b4c6fa92cd99c5c 301635%7C0%7C
Quoted 1 line
0%7C638917080648452454%7CUnknown%7CTWFpbGZsb3d8eyJFbXB 0eU1hcGkiOnRydWU
Quoted 1 line
sIlYiOiIwLjAuMDAwMCIsIlAiOiJXaW4zMiIsIkFOIjoiTWFpbCIsIldUIjoyfQ% 3D%3D%
Quoted 1 line
7C0%7C%7C%7C&sdata=neJx6WZU4iZWjSUcsnzOVQvFiaCTKLChE8srEx 6cwEQ%3D&rese
Quoted 11 lines
rved=0
This aligns the PMIC driver with current Linux and allows to use upstream devicetrees in U-Boot.
Frieder Schrempf (6):
Revert "pmic: pca9450: Add optionalSD_VSELGPIO for LDO5"
pmic: pca9450: Fix enable register for LDO5
pmic: pca9450: Fix control register for LDO5
pmic: pca9450: Handle hardware with fixedSD_VSELfor LDO5
arm: dts: imx8mp-data-modul-edm-sbc: Remove deprecated sd-vsel-gpios
Quoted 6 lines
arm: dts: imx8mp-dhcom-som: Remove deprecated sd-vsel-gpios
arch/arm/dts/imx8mp-data-modul-edm-sbc.dts | 1 - arch/arm/dts/imx8mp-dhcom-som.dtsi | 1 - drivers/power/pmic/pca9450.c | 22 ------------- drivers/power/regulator/pca9450.c | 37++++++++++++++++++++--
Quoted 2 lines
4 files changed, 34 insertions(+), 27 deletions(-)I saw that there are several patches on the mailing list for /drivers/power that have received no reply from a maintainer for several weeks (see [1]). I just wanted to make sure that you are aware of this and kindly ask to have a look.
Quoted 4 lines
Quoted 1 line
I could help handle that via mmc tree, if Tom and you are ok.
I don't mind. If Tom agrees to take power patches through the mmc tree from you that's fine.
This would be helpful, thanks!
Signature · 1 line
Tom
Peng Fan (OSS)
AppliedFrom: Peng Fan <[email protected]>
Quoted 8 lines · Frieder Schrempf
From: Frieder Schrempf <[email protected]>
This is a port for the following series in Linux, which is already available in mainline:
https://patchwork.kernel.org/project/linux-arm-kernel/cover/[email protected]/
[...]
Applied, thanks!
[1/6] Revert "pmic: pca9450: Add optional SD_VSEL GPIO for LDO5"
commit: b7360bd9e8e05dcfd1b4e5fd1c996aabf919e180
[2/6] pmic: pca9450: Fix enable register for LDO5
commit: 8a04fbd9afd635d37c9afc1b56d014d134861e29
[3/6] pmic: pca9450: Fix control register for LDO5
commit: addfe4544630a96a1cd03daf822a196af42b7a73
[4/6] pmic: pca9450: Handle hardware with fixed SD_VSEL for LDO5
commit: 281829f5ca1645c3bffa130d04753a1a76b64dfb
[5/6] arm: dts: imx8mp-data-modul-edm-sbc: Remove deprecated sd-vsel-gpios
commit: 925f63b0209483cd04b014cc8b5deab1f20267b7
[6/6] arm: dts: imx8mp-dhcom-som: Remove deprecated sd-vsel-gpios
commit: dc0a12fecea789de83015319f3e9aeddd0a824a2Best regards,
Signature · 1 line
Peng Fan <[email protected]>