Skip to contentSkip to conversation

Add Radxa CM5 module and IO board dts

PATCH Applied FUKAUMI Naoki 2 participants 5 messages Dec 5, 2025 – Dec 22, 2025

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

v6 cover Add Radxa CM5 module and IO board dts

This patch series adds initial device tree support for the Radxa CM5 SoM and accompanying IO board.

V5 -> V6:
Patch (2/3)
- Move gmac1 (except status) from cm5-io.dts (Jimmy)
- Move pmic from cm5-io.dts (Dmitriy)

Patch (3/3)
- Remove regulator-{always,boot}-on from vcc3v3_pcie (Shawn)
- Remove max-frequency from sdmmc (Shawn)
- Remove no-mmc from sdmmc (Jimmy)

V4 -> V5:
Patch (2/3), per Jimmy:
- Alias eMMC to mmc0
- Remove unused sdio alias
- Move gmac, hdmi0 nodes to carrier board dts

Patch (3/3), per Jimmy:
- Enable hdmi0_sound and i2s5_8ch
- Remove redundant enablement of sdhci
- Enable usb_host2_xhci

- Tested HDMI audio

V3 -> V4:
- Fixed XHCI initialization bug by changing try-power-role from source to sink

V2 -> V3:
- Addressed YAML syntax error in dt binding (per Rob)
- Fixed whitespace issue in dts reported by checkpatch.pl
- Split base SoM and carrier board into separate patches
- Added further details about the SoM and carrier to the commit messages

V1 -> V2:
- Added copyright header and data sheet links
- Removed non-existent property
- Sorted alphabetically
- Removed errant whitespace
- Moved status to the end of each node
- Removed pinctrl-names property from leds (indicated by CHECK_DTBS)
- Removed delays from gmac with internal delay

- Link to v4: https://lore.kernel.org/r/[email protected]

Joseph Kogut (3):
dt-bindings: arm: rockchip: Add Radxa CM5 IO board
arm64: dts: rockchip: Add rk3588 based Radxa CM5
arm64: dts: rockchip: Add support for CM5 IO carrier

 .../devicetree/bindings/arm/rockchip.yaml     |   7 +
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../dts/rockchip/rk3588s-radxa-cm5-io.dts     | 339 ++++++++++++++++++
 .../boot/dts/rockchip/rk3588s-radxa-cm5.dtsi  | 280 +++++++++++++++
 4 files changed, 627 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-radxa-cm5-io.dts
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-radxa-cm5.dtsi
Signature · 7 lines
2.43.0


_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
#1 lore raw

PATCH v6 1/3 dt-bindings: arm: rockchip: Add Radxa CM5 IO board

From: Joseph Kogut <[email protected]>

Add device tree binding for the Radxa CM5 IO board.

This board is based on the rk3588s.

---
 Documentation/devicetree/bindings/arm/rockchip.yaml | 7 +++++++
 1 file changed, 7 insertions(+)
Documentation/devicetree/bindings/arm/rockchip.yaml +7 -0
index d496421dbd87..79e99694577e 100644
@@ -907,6 +907,13 @@ properties:
           - const: radxa,cm3
           - const: rockchip,rk3566
 
+      - description: Radxa Compute Module 5 (CM5)
+        items:
+          - enum:
+              - radxa,cm5-io
+          - const: radxa,cm5
+          - const: rockchip,rk3588s
+
       - description: Radxa CM3 Industrial
         items:
           - enum:
Signature · 7 lines
2.43.0


_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
#2 lore raw

PATCH v6 2/3 arm64: dts: rockchip: Add rk3588 based Radxa CM5

In reply to FUKAUMI Naoki

From: Joseph Kogut <[email protected]>

Add initial support for the Radxa Compute Module 5 (CM5). The CM5 uses a proprietary connector.

Specification:
- Rockchip RK3588
- Up to 32 GB LPDDR4X
- Up to 128 GB eMMC
- 1x HDMI TX up to 8k@60 hz
- 1x eDP TX up to 4k@60 hz
- Gigabit Ethernet PHY

---
 .../boot/dts/rockchip/rk3588s-radxa-cm5.dtsi  | 280 ++++++++++++++++++
 1 file changed, 280 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-radxa-cm5.dtsi
arch/arm64/boot/dts/rockchip/rk3588s-radxa-cm5.dtsi new file +280 -0
new file mode 100644
index 000000000000..d307e19052c6
@@ -0,0 +1,280 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2025 Joseph Kogut <[email protected]>
+ */
+
+/*
+ * CM5 data sheet
+ * https://dl.radxa.com/cm5/v2210/radxa_cm5_v2210_schematic.pdf
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include <dt-bindings/usb/pd.h>
+
+/ {
+	compatible = "radxa,cm5", "rockchip,rk3588s";
+
+	aliases {
+		mmc0 = &sdhci;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_sys: led-0 {
+			color = <LED_COLOR_ID_BLUE>;
+			default-state = "on";
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
+
+&cpu_b0 {
+	cpu-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b1 {
+	cpu-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b2 {
+	cpu-supply = <&vdd_cpu_big1_s0>;
+};
+
+&cpu_b3 {
+	cpu-supply = <&vdd_cpu_big1_s0>;
+};
+
+&cpu_l0 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l1 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l2 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l3 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&gmac1 {
+	clock_in_out = "output";
+	phy-handle = <&rgmii_phy1>;
+	phy-mode = "rgmii-id";
+	phy-supply = <&vcc_3v3_s0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1_miim
+		     &gmac1_tx_bus2
+		     &gmac1_rx_bus2
+		     &gmac1_rgmii_clk
+		     &gmac1_rgmii_bus
+		     &gmac1_clkinout>;
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu_s0>;
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0m2_xfer>;
+	status = "okay";
+
+	vdd_cpu_big0_s0: regulator@42 {
+		compatible = "rockchip,rk8602";
+		reg = <0x42>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu_big0_s0";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <550000>;
+		regulator-max-microvolt = <1050000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vdd_cpu_big1_s0: regulator@43 {
+		compatible = "rockchip,rk8602";
+		reg = <0x43>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu_big1_s0";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <550000>;
+		regulator-max-microvolt = <1050000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&mdio1 {
+	rgmii_phy1: phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x1>;
+	};
+};
+
+&pd_gpu {
+	domain-supply = <&vdd_gpu_s0>;
+};
+
+&sdhci {
+	bus-width = <8>;
+	no-sdio;
+	no-sd;
+	non-removable;
+	max-frequency = <200000000>;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+	mmc-hs200-1_8v;
+	status = "okay";
+};
+
+&spi2 {
+	assigned-clocks = <&cru CLK_SPI2>;
+	assigned-clock-rates = <200000000>;
+	num-cs = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>;
+	status = "okay";
+
+	pmic@0 {
+		compatible = "rockchip,rk806";
+		reg = <0x0>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
+			    <&rk806_dvs2_null>, <&rk806_dvs3_null>;
+		spi-max-frequency = <1000000>;
+		system-power-controller;
+
+		vcc1-supply = <&vcc5v0_sys>;
+		vcc2-supply = <&vcc5v0_sys>;
+		vcc3-supply = <&vcc5v0_sys>;
+		vcc4-supply = <&vcc5v0_sys>;
+		vcc5-supply = <&vcc5v0_sys>;
+		vcc6-supply = <&vcc5v0_sys>;
+		vcc7-supply = <&vcc5v0_sys>;
+		vcc8-supply = <&vcc5v0_sys>;
+		vcc9-supply = <&vcc5v0_sys>;
+		vcc10-supply = <&vcc5v0_sys>;
+		vcc11-supply = <&vcc_2v0_pldo_s3>;
+		vcc12-supply = <&vcc5v0_sys>;
+		vcc13-supply = <&vdd2_ddr_s3>;
+		vcc14-supply = <&vdd2_ddr_s3>;
+		vcca-supply = <&vcc5v0_sys>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		rk806_dvs1_null: dvs1-null-pins {
+			pins = "gpio_pwrctrl1";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs2_null: dvs2-null-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs3_null: dvs3-null-pins {
+			pins = "gpio_pwrctrl3";
+			function = "pin_fun0";
+		};
+
+		regulators {
+			vdd_gpu_s0: dcdc-reg1 {
+				regulator-name = "vdd_gpu_s0";
+				regulator-boot-on;
+				regulator-enable-ramp-delay = <400>;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_cpu_lit_s0: dcdc-reg2 {
+				regulator-name = "vdd_cpu_lit_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd_s0: pldo-reg5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd2_ddr_s3: dcdc-reg6 {
+				regulator-name = "vdd2_ddr_s3";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_2v0_pldo_s3: dcdc-reg7 {
+				regulator-name = "vdd_2v0_pldo_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <2000000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <2000000>;
+				};
+			};
+
+			vcc_3v3_s3: dcdc-reg8 {
+				regulator-name = "vcc_3v3_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+		};
+	};
+};
Signature · 7 lines
2.43.0


_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
#3 lore raw

PATCH v6 3/3 arm64: dts: rockchip: Add support for CM5 IO carrier

In reply to FUKAUMI Naoki

From: Joseph Kogut <[email protected]>

Specification:
- 1x HDMI
- 2x MIPI DSI
- 2x MIPI CSI
- 1x eDP
- 1x M.2 E key
- 1x USB 3.0 Host
- 1x USB 3.0 OTG
- 2x USB 2.0 Host
- Headphone jack w/ microphone
- Gigabit Ethernet w/ PoE
- microSD slot
- 40-pin expansion header
- 12V DC

---
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../dts/rockchip/rk3588s-radxa-cm5-io.dts     | 339 ++++++++++++++++++
 2 files changed, 340 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-radxa-cm5-io.dts
arch/arm64/boot/dts/rockchip/Makefile +1 -0
index dbdda9783e93..699ed38235fe 100644
@@ -209,6 +209,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-nanopi-r6c.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-odroid-m2.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5b.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-radxa-cm5-io.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-roc-pc.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-rock-5a.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-rock-5c.dtb
arch/arm64/boot/dts/rockchip/rk3588s-radxa-cm5-io.dts new file +339 -0

339 lines not on this page · raw message

Signature · 7 lines
2.43.0


_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
maintainer Applied
#4 lore raw
In reply to FUKAUMI Naoki
Quoted 9 lines · FUKAUMI Naoki

This patch series adds initial device tree support for the Radxa CM5 SoM and accompanying IO board.

V5 -> V6:
Patch (2/3)
- Move gmac1 (except status) from cm5-io.dts (Jimmy)
- Move pmic from cm5-io.dts (Dmitriy)

[...]

Applied, thanks!

[1/3] dt-bindings: arm: rockchip: Add Radxa CM5 IO board

      commit: 7beae528ddadd1c3f7d5670f937d993b0f39e0ea
[2/3] arm64: dts: rockchip: Add rk3588 based Radxa CM5
      commit: 36ee19ba42dcebe6a15ec6b442a7d32eb327eee4
[3/3] arm64: dts: rockchip: Add support for CM5 IO carrier
      commit: 51babf83f424a695179183204226d453c8af7dc7

Best regards,

Signature · 1 line
Heiko Stuebner <[email protected]>