Skip to contentSkip to conversation

imu: st_lsm6dsx: Add support for rotation sensor

PATCH Superseded Francesco Lavra 2 participants 9 messages Jan 21

Subsystems (2)

v4 of 9 Superseded Latest is v9 →

lore
Share & tools
lore
#0 lore raw

v4 cover imu: st_lsm6dsx: Add support for rotation sensor

This series adds support for the rotation sensor functionality present in some chips from the ST LSM6DSX IMU family.
The second commit is a fix to a previous commit of mine [*] which made it to 6.19-rcX; the fix technically changes userspace, but this should be OK as long as it goes in during this release cycle.
Tested on LSM6DSV16X.

Changes from v3 [3]:
- added patch 3 (Andy)
- removed unneeded checks for negative return values in st_lsm6dsx_fusion.c (Andy)
- replaced st_lsm6dsx_sf_set_page function with st_lsm6dsx_sf_page_enable/disable (Andy)
- used reversed xmas tree ordering for local variables (Andy)
- added parentheses to MILLI / MICRO in st_lsm6dsx_sf_write_raw (Andy)
- added check for string truncation in st_lsm6dsx_sf_probe (Andy)

Changes from v2 [2]:
- amended description of patch 2 to point out that there are no supported gyro events (Jonathan)
- removed superfluous parentheses in st_lsm6dsx_fifo_setup (Lorenzo)
- added Lorenzo's acked-by tag to patch 3
- added missing checks of st_lsm6dsx_sf_set_page() return value (Jonathan)
- added comment in st_lsm6dsx_sf_write_raw (Jonathan)

Changes from v1 [1]:
- swapped patches 1 and 2 (Jonathan)
- miscellaneous stylistic changes (Andy)
- fixed usage of MICRO and MILLI constants in st_lsm6dsx_sf_read_raw and st_lsm6dsx_sf_write_raw (Andy)
- replaced scnprintf() with sysfs_emit_at() in st_lsm6dsx_sf_sampling_freq_avail (Andy)
- replaced scnprintf() with snprintf() in st_lsm6dsx_sf_probe (Andy)
- clarified in a comment in st_lsm6dsx_set_fifo_odr() that only internal sensors have a FIFO ODR configuration register (Jonathan)
- modified patch 3 description to explain justification for the extra IIO device (Jonathan)
- moved page lock from st_lsm6dsx_sf_set_page() to the callers (Jonathan)
- s/magnetometer/gyroscope/ in patch 2 description

[*] https://lore.kernel.org/linux-iio/[email protected]/
[1] https://lore.kernel.org/linux-iio/[email protected]/T/
[2] https://lore.kernel.org/linux-iio/[email protected]/T/
[3] https://lore.kernel.org/linux-iio/[email protected]/T/

Francesco Lavra (4):
iio: imu: st_lsm6dsx: Set FIFO ODR for accelerometer and gyroscope
only
iio: imu: st_lsm6dsx: Set buffer sampling frequency for accelerometer
only
iio: imu: st_lsm6dsx: Fix check for invalid samples from FIFO
iio: imu: st_lsm6dsx: Add support for rotation sensor

 drivers/iio/imu/st_lsm6dsx/Makefile           |   2 +-
 drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h       |  26 +-
 .../iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c    |  33 ++-
 drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c  |  58 +++++
 .../iio/imu/st_lsm6dsx/st_lsm6dsx_fusion.c    | 235 ++++++++++++++++++
 5 files changed, 345 insertions(+), 9 deletions(-)
 create mode 100644 drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_fusion.c
Signature · 1 line
2.39.5
#1 lore raw

PATCH v4 1/4 iio: imu: st_lsm6dsx: Set FIFO ODR for accelerometer and gyroscope only

The st_lsm6dsx_set_fifo_odr() function, which is called when enabling and disabling the hardware FIFO, checks the contents of the hw->settings->batch array at index sensor->id, and then sets the current ODR value in sensor registers that depend on whether the register address is set in the above array element. This logic is valid for internal sensors only, i.e. the accelerometer and gyroscope; however, since commit c91c1c844ebd ("iio: imu:
st_lsm6dsx: add i2c embedded controller support"), this function is called also when configuring the hardware FIFO for external sensors (i.e. sensors accessed through the sensor hub functionality), which can result in unrelated device registers being written.

Add a check to the beginning of st_lsm6dsx_set_fifo_odr() so that it does not touch any registers unless it is called for internal sensors.

Fixes c91c1c844ebd ("iio: imu: st_lsm6dsx: add i2c embedded controller support")
---
 drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c | 4 ++++
 1 file changed, 4 insertions(+)
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c +4 -0
index 55d877745575..1ee2fc5f5f1f 100644
@@ -225,6 +225,10 @@ static int st_lsm6dsx_set_fifo_odr(struct st_lsm6dsx_sensor *sensor,
 	const struct st_lsm6dsx_reg *batch_reg;
 	u8 data;
 
+	/* Only internal sensors have a FIFO ODR configuration register. */
+	if (sensor->id >= ARRAY_SIZE(hw->settings->batch))
+		return 0;
+
 	batch_reg = &hw->settings->batch[sensor->id];
 	if (batch_reg->addr) {
 		int val;
Signature · 1 line
2.39.5
#2 lore raw

PATCH v4 2/4 iio: imu: st_lsm6dsx: Set buffer sampling frequency for accelerometer only

In reply to Francesco Lavra

The st_lsm6dsx_hwfifo_odr_store() function, which is called when userspace writes the buffer sampling frequency sysfs attribute, calls st_lsm6dsx_check_odr(), which accesses the odr_table array at index sensor->id; since this array is only 2 entries long, an access for any sensor type other than accelerometer or gyroscope is an out-of-bounds access.

The motivation for being able to set a buffer frequency different from the sensor sampling frequency is to support use cases that need accurate event detection (which requires a high sampling frequency) while retrieving sensor data at low frequency. Since all the supported event types are generated from acceleration data only, do not create the buffer sampling frequency attribute for sensor types other than the accelerometer.

Fixes 6b648a36c200 ("iio: imu: st_lsm6dsx: Decouple sensor ODR from FIFO batch data rate")
---
 drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c | 11 ++++++++++-
 1 file changed, 10 insertions(+), 1 deletion(-)
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c +10 -1
index 1ee2fc5f5f1f..5b28a3ffcc3d 100644
@@ -862,12 +862,21 @@ int st_lsm6dsx_fifo_setup(struct st_lsm6dsx_hw *hw)
 	int i, ret;
 
 	for (i = 0; i < ST_LSM6DSX_ID_MAX; i++) {
+		const struct iio_dev_attr **attrs;
+
 		if (!hw->iio_devs[i])
 			continue;
 
+		/*
+		 * For the accelerometer, allow setting FIFO sampling frequency
+		 * values different from the sensor sampling frequency, which
+		 * may be needed to keep FIFO data rate low while sampling
+		 * acceleration data at high rates for accurate event detection.
+		 */
+		attrs = i == ST_LSM6DSX_ID_ACC ? st_lsm6dsx_buffer_attrs : NULL;
 		ret = devm_iio_kfifo_buffer_setup_ext(hw->dev, hw->iio_devs[i],
 						      &st_lsm6dsx_buffer_ops,
-						      st_lsm6dsx_buffer_attrs);
+						      attrs);
 		if (ret)
 			return ret;
 	}
Signature · 1 line
2.39.5
#3 lore raw

PATCH 1/1 iio: imu: st_lsm6dsx: Fix check for invalid samples from FIFO

In reply to Francesco Lavra

The DRDY_MASK feature implemented in sensor chips marks gyroscope and accelerometer invalid samples (i.e. samples that have been acquired during the settling time of sensor filters) with the special values 0x7FFFh, 0x7FFE, and 0x7FFD.
The driver checks FIFO samples against these special values in order to discard invalid samples; however, it does the check regardless of the type of samples being processed, whereas this feature is specific to gyroscope and accelerometer data. This could cause valid samples to be discarded. Fix the above check so that it takes into account the type of samples being processed.

Fixes 960506ed2c69 ("iio: imu: st_lsm6dsx: enable drdy-mask if available")
---
 drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c +2 -2
index 5b28a3ffcc3d..4cfd5046f98e 100644
@@ -541,12 +541,12 @@ static int
 st_lsm6dsx_push_tagged_data(struct st_lsm6dsx_hw *hw, u8 tag,
 			    u8 *data, s64 ts)
 {
-	s16 val = le16_to_cpu(*(__le16 *)data);
 	struct st_lsm6dsx_sensor *sensor;
 	struct iio_dev *iio_dev;
 
 	/* invalid sample during bootstrap phase */
-	if (val >= ST_LSM6DSX_INVALID_SAMPLE)
+	if ((tag == ST_LSM6DSX_GYRO_TAG || tag == ST_LSM6DSX_ACC_TAG) &&
+	    (s16)le16_to_cpup((__le16 *)data) >= ST_LSM6DSX_INVALID_SAMPLE)
 		return -EINVAL;
 
 	/*
Signature · 1 line
2.39.5
#4 lore raw

Re: [PATCH] iio: imu: st_lsm6dsx: Fix check for invalid samples from FIFO

Quoted 10 lines · Francesco Lavra

The DRDY_MASK feature implemented in sensor chips marks gyroscope and accelerometer invalid samples (i.e. samples that have been acquired during the settling time of sensor filters) with the special values 0x7FFFh, 0x7FFE, and 0x7FFD.
The driver checks FIFO samples against these special values in order to discard invalid samples; however, it does the check regardless of the type of samples being processed, whereas this feature is specific to gyroscope and accelerometer data. This could cause valid samples to be discarded. Fix the above check so that it takes into account the type of samples being processed.

...

drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c static int · line 549

Quoted 11 lines

st_lsm6dsx_push_tagged_data(struct st_lsm6dsx_hw *hw, u8 tag,

drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c +2 -2
 			    u8 *data, s64 ts)
 {
-	s16 val = le16_to_cpu(*(__le16 *)data);
 	struct st_lsm6dsx_sensor *sensor;
 	struct iio_dev *iio_dev;
 
 	/* invalid sample during bootstrap phase */
-	if (val >= ST_LSM6DSX_INVALID_SAMPLE)
+	if ((tag == ST_LSM6DSX_GYRO_TAG || tag == ST_LSM6DSX_ACC_TAG) &&
+	    (s16)le16_to_cpup((__le16 *)data) >= ST_LSM6DSX_INVALID_SAMPLE)

Since data is u8 *, it might appear on unaligned addresses and the proper conversion here is to use get_unaligned_le16() without any of those ugly castings.

Quoted 1 line

return -EINVAL;

Signature · 2 lines
With Best Regards,
Andy Shevchenko
#5 lore raw

Re: [PATCH] iio: imu: st_lsm6dsx: Fix check for invalid samples from FIFO

Quoted 1 line · Andy Shevchenko

On Wed, Jan 21, 2026 at 12:27:57PM +0100, Francesco Lavra wrote:

...

Quoted 7 lines
Quoted 7 lines

st_lsm6dsx_push_tagged_data(struct st_lsm6dsx_hw *hw, u8 tag,

drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c +0 -1
 			    u8 *data, s64 ts)
 {
-	s16 val = le16_to_cpu(*(__le16 *)data);
 	struct st_lsm6dsx_sensor *sensor;
 	struct iio_dev *iio_dev;
Quoted 8 lines

drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c static int · line 549

Quoted 4 lines
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c +2 -1
 	/* invalid sample during bootstrap phase */
-	if (val >= ST_LSM6DSX_INVALID_SAMPLE)
+	if ((tag == ST_LSM6DSX_GYRO_TAG || tag == ST_LSM6DSX_ACC_TAG) &&
+	    (s16)le16_to_cpup((__le16 *)data) >= ST_LSM6DSX_INVALID_SAMPLE)

Since data is u8 *, it might appear on unaligned addresses and the proper conversion here is to use get_unaligned_le16() without any of those ugly castings.

Okay, (s16) seems needed or another way to allow 0x8000 and higher values.

Quoted 1 line
Quoted 1 line

return -EINVAL;

Signature · 2 lines
With Best Regards,
Andy Shevchenko
#6 lore raw

Re: [PATCH] iio: imu: st_lsm6dsx: Fix check for invalid samples from FIFO

In reply to Andy Shevchenko
Quoted 32 lines · Andy Shevchenko
Quoted 14 lines · Francesco Lavra

The DRDY_MASK feature implemented in sensor chips marks gyroscope and accelerometer invalid samples (i.e. samples that have been acquired during
the settling time of sensor filters) with the special values 0x7FFFh, 0x7FFE, and 0x7FFD.
The driver checks FIFO samples against these special values in order to discard invalid samples; however, it does the check regardless of the type
of samples being processed, whereas this feature is specific to gyroscope
and accelerometer data. This could cause valid samples to be discarded. Fix the above check so that it takes into account the type of samples being
processed.

...

Quoted 5 lines

 st_lsm6dsx_push_tagged_data(struct st_lsm6dsx_hw *hw, u8 tag, u8 *data, s64 ts)
 {
-       s16 val = le16_to_cpu(*(__le16 *)data); struct st_lsm6dsx_sensor *sensor;

Quoted 8 lines

        struct iio_dev *iio_dev;

        /* invalid sample during bootstrap phase */
-       if (val >= ST_LSM6DSX_INVALID_SAMPLE)
+       if ((tag == ST_LSM6DSX_GYRO_TAG || tag == ST_LSM6DSX_ACC_TAG) &&
+           (s16)le16_to_cpup((__le16 *)data) >= ST_LSM6DSX_INVALID_SAMPLE)

Quoted 3 lines

Since data is u8 *, it might appear on unaligned addresses and the proper conversion here is to use get_unaligned_le16() without any of those ugly castings.

data here corresponds to iio_buff in st_lsm6dsx_read_tagged_fifo(), which is declared as __aligned(8), so it cannot appear on unaligned addresses.

Quoted 2 lines
Quoted 1 line

                return -EINVAL;

#7 lore raw

Re: [PATCH] iio: imu: st_lsm6dsx: Fix check for invalid samples from FIFO

Quoted 2 lines · Francesco Lavra
Quoted 1 line · Andy Shevchenko

On Wed, Jan 21, 2026 at 12:27:57PM +0100, Francesco Lavra wrote:

...

Quoted 14 lines
Quoted 14 lines
Quoted 13 lines

 st_lsm6dsx_push_tagged_data(struct st_lsm6dsx_hw *hw, u8 tag, u8 *data, s64 ts)
 {
-       s16 val = le16_to_cpu(*(__le16 *)data);
        struct st_lsm6dsx_sensor *sensor;
        struct iio_dev *iio_dev;

        /* invalid sample during bootstrap phase */
-       if (val >= ST_LSM6DSX_INVALID_SAMPLE)
+       if ((tag == ST_LSM6DSX_GYRO_TAG || tag == ST_LSM6DSX_ACC_TAG) &&
+           (s16)le16_to_cpup((__le16 *)data) >= ST_LSM6DSX_INVALID_SAMPLE)

Quoted 6 lines
Quoted 3 lines

Since data is u8 *, it might appear on unaligned addresses and the proper conversion here is to use get_unaligned_le16() without any of those ugly castings.

data here corresponds to iio_buff in st_lsm6dsx_read_tagged_fifo(), which is declared as __aligned(8), so it cannot appear on unaligned addresses.

You know that, compiler might not. If you sure, you should change u8 *data to be __le16 *data in the function parameter. Until it's u8 *, the get_unaligned_le16() is the error free thing to achieve that.

Quoted 1 line
Quoted 1 line
Quoted 1 line

                return -EINVAL;

Signature · 2 lines
With Best Regards,
Andy Shevchenko
#8 lore raw

PATCH 1/1 iio: imu: st_lsm6dsx: Add support for rotation sensor

In reply to Francesco Lavra

Some IMU chips in the LSM6DSX family have sensor fusion features that combine data from the accelerometer and gyroscope. One of these features generates rotation vector data and makes it available in the hardware FIFO as a quaternion (more specifically, the X, Y and Z components of the quaternion vector, expressed as 16-bit half-precision floating-point numbers).

Add support for a new sensor instance that allows receiving sensor fusion data, by defining a new struct st_lsm6dsx_sf_settings (which contains chip-specific details for the sensor fusion functionality), and adding this struct as a new field in struct st_lsm6dsx_settings. In st_lsm6dsx_core.c, populate this new struct for the LSM6DSV and LSM6DSV16X chips, and add the logic to initialize an additional IIO device if this struct is populated for the hardware type being probed.
Note: a new IIO device is being defined (as opposed to adding channels to an existing device) because the rate at which sensor fusion data is generated may not match the data rate from any of the existing devices.

Tested on LSMDSV16X.

---
 drivers/iio/imu/st_lsm6dsx/Makefile           |   2 +-
 drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h       |  26 +-
 .../iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c    |  16 +-
 drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c  |  58 +++++
 .../iio/imu/st_lsm6dsx/st_lsm6dsx_fusion.c    | 235 ++++++++++++++++++
 5 files changed, 330 insertions(+), 7 deletions(-)
 create mode 100644 drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_fusion.c
drivers/iio/imu/st_lsm6dsx/Makefile +1 -1
index 57cbcd67d64f..19a488254de3 100644
@@ -1,6 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0-only
 st_lsm6dsx-y := st_lsm6dsx_core.o st_lsm6dsx_buffer.o \
-		st_lsm6dsx_shub.o
+		st_lsm6dsx_shub.o st_lsm6dsx_fusion.o
 
 obj-$(CONFIG_IIO_ST_LSM6DSX) += st_lsm6dsx.o
 obj-$(CONFIG_IIO_ST_LSM6DSX_I2C) += st_lsm6dsx_i2c.o
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h +21 -5
index 07b1773c87bd..4173f670f7af 100644
@@ -294,6 +294,7 @@ enum st_lsm6dsx_sensor_id {
 	ST_LSM6DSX_ID_EXT0,
 	ST_LSM6DSX_ID_EXT1,
 	ST_LSM6DSX_ID_EXT2,
+	ST_LSM6DSX_ID_SF,
 	ST_LSM6DSX_ID_MAX
 };
 
@@ -301,6 +302,15 @@ enum st_lsm6dsx_ext_sensor_id {
 	ST_LSM6DSX_ID_MAGN,
 };
 
+struct st_lsm6dsx_sf_settings {
+	const struct iio_chan_spec *chan;
+	int chan_len;
+	struct st_lsm6dsx_odr_table_entry odr_table;
+	struct st_lsm6dsx_reg fifo_enable;
+	struct st_lsm6dsx_reg page_mux;
+	struct st_lsm6dsx_reg enable;
+};
+
 /**
  * struct st_lsm6dsx_ext_dev_settings - i2c controller slave settings
  * @i2c_addr: I2c slave address list.
@@ -388,6 +398,7 @@ struct st_lsm6dsx_settings {
 	struct st_lsm6dsx_hw_ts_settings ts_settings;
 	struct st_lsm6dsx_shub_settings shub_settings;
 	struct st_lsm6dsx_event_settings event_settings;
+	struct st_lsm6dsx_sf_settings sf_settings;
 };
 
 enum st_lsm6dsx_fifo_mode {
@@ -510,6 +521,9 @@ int st_lsm6dsx_check_odr(struct st_lsm6dsx_sensor *sensor, u32 odr, u8 *val);
 int st_lsm6dsx_shub_probe(struct st_lsm6dsx_hw *hw, const char *name);
 int st_lsm6dsx_shub_set_enable(struct st_lsm6dsx_sensor *sensor, bool enable);
 int st_lsm6dsx_shub_read_output(struct st_lsm6dsx_hw *hw, u8 *data, int len);
+int st_lsm6dsx_sf_probe(struct st_lsm6dsx_hw *hw, const char *name);
+int st_lsm6dsx_sf_set_enable(struct st_lsm6dsx_sensor *sensor, bool enable);
+int st_lsm6dsx_sf_set_odr(struct st_lsm6dsx_sensor *sensor, bool enable);
 int st_lsm6dsx_set_page(struct st_lsm6dsx_hw *hw, bool enable);
 
 static inline int
@@ -564,12 +578,14 @@ st_lsm6dsx_get_mount_matrix(const struct iio_dev *iio_dev,
 static inline int
 st_lsm6dsx_device_set_enable(struct st_lsm6dsx_sensor *sensor, bool enable)
 {
-	if (sensor->id == ST_LSM6DSX_ID_EXT0 ||
-	    sensor->id == ST_LSM6DSX_ID_EXT1 ||
-	    sensor->id == ST_LSM6DSX_ID_EXT2)
+	switch (sensor->id) {
+	case ST_LSM6DSX_ID_EXT0 ... ST_LSM6DSX_ID_EXT2:
 		return st_lsm6dsx_shub_set_enable(sensor, enable);
-
-	return st_lsm6dsx_sensor_set_enable(sensor, enable);
+	case ST_LSM6DSX_ID_SF:
+		return st_lsm6dsx_sf_set_enable(sensor, enable);
+	default:
+		return st_lsm6dsx_sensor_set_enable(sensor, enable);
+	}
 }
 
 static const
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c +15 -1
index df93dbc0a530..60792b810abc 100644
@@ -88,6 +88,7 @@ enum st_lsm6dsx_fifo_tag {
 	ST_LSM6DSX_EXT0_TAG = 0x0f,
 	ST_LSM6DSX_EXT1_TAG = 0x10,
 	ST_LSM6DSX_EXT2_TAG = 0x11,
+	ST_LSM6DSX_ROT_TAG = 0x13,
 };
 
 static const
@@ -226,8 +227,11 @@ static int st_lsm6dsx_set_fifo_odr(struct st_lsm6dsx_sensor *sensor,
 	u8 data;
 
 	/* Only internal sensors have a FIFO ODR configuration register. */
-	if (sensor->id >= ARRAY_SIZE(hw->settings->batch))
+	if (sensor->id >= ARRAY_SIZE(hw->settings->batch)) {
+		if (sensor->id == ST_LSM6DSX_ID_SF)
+			return st_lsm6dsx_sf_set_odr(sensor, enable);
 		return 0;
+	}
 
 	batch_reg = &hw->settings->batch[sensor->id];
 	if (batch_reg->addr) {
@@ -580,6 +584,16 @@ st_lsm6dsx_push_tagged_data(struct st_lsm6dsx_hw *hw, u8 tag,
 	case ST_LSM6DSX_EXT2_TAG:
 		iio_dev = hw->iio_devs[ST_LSM6DSX_ID_EXT2];
 		break;
+	case ST_LSM6DSX_ROT_TAG:
+		/*
+		 * The sensor reports only the {X, Y, Z} elements of the
+		 * quaternion vector; set the W value to 0 (it can be derived
+		 * from the {X, Y, Z} values due to the property that the vector
+		 * is normalized).
+		 */
+		*(u16 *)(data + ST_LSM6DSX_SAMPLE_SIZE) = 0;
+		iio_dev = hw->iio_devs[ST_LSM6DSX_ID_SF];
+		break;
 	default:
 		return -EINVAL;
 	}
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c +58 -0

82 lines not on this page · raw message

drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_fusion.c new file +235 -0

235 lines not on this page · raw message

Signature · 1 line
2.39.5