iio: adc: ina2xx: add INA236 support
PATCH 1/1 iio: adc: ina2xx: add INA236 support
The calibration divisor is not directly specified in the datasheet, but can be calculated:
I = Current_LSB * Current
Current = ShuntVoltage * CAL / calibration_divisor CAL = 0.00512 / (Current_LSB * Rshunt) ShuntVoltage = Vshunt / ShuntVoltage_LSB
=> I = (0.00512 / (calibration_divisor*ShuntVoltage_LSB)) * (Vshunt / Rshunt)
Ohm's law, I = Vshunt / Rshunt
=> 0.00512 / (calibration_divisor*ShuntVoltage_LSB) = 1
ShuntVoltage_LSB = 2.5 uV = 0.0000025 V
=> calibration_divisor = 2048
--- drivers/iio/adc/ina2xx-adc.c | 25 ++++++++++++++++++++----- 1 file changed, 20 insertions(+), 5 deletions(-)
drivers/iio/adc/ina2xx-adc.c +20 -5
@@ -121,7 +121,7 @@ static const struct regmap_config ina2xx_regmap_config = { .volatile_reg = ina2xx_is_volatile_reg, }; -enum ina2xx_ids { ina219, ina226 }; +enum ina2xx_ids { ina219, ina226, ina236 };struct ina2xx_config {const char *name;
@@ -175,6 +175,16 @@ static const struct ina2xx_config ina2xx_config[] = { .power_lsb_factor = 25, .chip_id = ina226, }, + [ina236] = { + .name = "ina236", + .config_default = INA226_CONFIG_DEFAULT, + .calibration_value = 2048, + .shunt_voltage_lsb = 2500, + .bus_voltage_shift = 0, + .bus_voltage_lsb = 1600, + .power_lsb_factor = 32, + .chip_id = ina236, + }, }; static int ina2xx_read_raw(struct iio_dev *indio_dev,
@@ -499,7 +509,7 @@ static int ina2xx_write_raw(struct iio_dev *indio_dev,break ;case IIO_CHAN_INFO_INT_TIME : -if (chip->config->chip_id == ina226) { +if (chip->config->chip_id != ina219) {if (chan->address ==INA2XX_SHUNT_VOLTAGE ) ret =ina226_set_int_time_vshunt (chip, val2, &tmp);
@@ -727,7 +737,7 @@ static int ina2xx_conversion_ready(struct iio_dev *indio_dev)* For now, we do an extra read of the MASK_ENABLE register (INA226) * resp. the BUS_VOLTAGE register (INA219). */ -if (chip->config->chip_id == ina226) { +if (chip->config->chip_id != ina219) { ret =regmap_read (chip->regmap,INA226_MASK_ENABLE , &alert); alert &=INA226_CVRF ;
@@ -998,7 +1008,7 @@ static int ina2xx_probe(struct i2c_client *client)/* Patch the current config register with default. */ val = chip->config->config_default; -if (type == ina226) { +if (type != ina219) {ina226_set_average (chip,INA226_DEFAULT_AVG , &val);ina226_set_int_time_vbus (chip,INA226_DEFAULT_IT , &val);ina226_set_int_time_vshunt (chip,INA226_DEFAULT_IT , &val);
@@ -1017,7 +1027,7 @@ static int ina2xx_probe(struct i2c_client *client) } indio_dev->modes =INDIO_DIRECT_MODE ; -if (type == ina226) { +if (type != ina219) { indio_dev->channels = ina226_channels; indio_dev->num_channels =ARRAY_SIZE (ina226_channels); indio_dev->info = &ina226_info;
@@ -1057,6 +1067,7 @@ static const struct i2c_device_id ina2xx_id[] = { { "ina226", ina226 }, { "ina230", ina226 }, { "ina231", ina226 }, + { "ina236", ina236 }, { } };MODULE_DEVICE_TABLE (i2c, ina2xx_id);
@@ -1082,6 +1093,10 @@ static const struct of_device_id ina2xx_of_match[] = { .compatible = "ti,ina231", .data = (void *)ina226 }, + { + .compatible = "ti,ina236", + .data = (void *)ina236 + }, { } };MODULE_DEVICE_TABLE (of, ina2xx_of_match);
Signature · 1 line
2.51.2