Skip to contentSkip to conversation

iio: adc: ina2xx: add INA236 support

PATCH Superseded Chuang Zhu 1 participant 1 message Mar 9 IIO

v1 of 3 Superseded Latest is v3 →

lore
Share & tools
lore

Chuang Zhu

author
#0 lore raw

PATCH 1/1 iio: adc: ina2xx: add INA236 support

The calibration divisor is not directly specified in the datasheet, but can be calculated:

I = Current_LSB * Current
Current = ShuntVoltage * CAL / calibration_divisor CAL = 0.00512 / (Current_LSB * Rshunt) ShuntVoltage = Vshunt / ShuntVoltage_LSB

=> I = (0.00512 / (calibration_divisor*ShuntVoltage_LSB)) * (Vshunt / Rshunt)

Ohm's law, I = Vshunt / Rshunt
=> 0.00512 / (calibration_divisor*ShuntVoltage_LSB) = 1

ShuntVoltage_LSB = 2.5 uV = 0.0000025 V
=> calibration_divisor = 2048

---
 drivers/iio/adc/ina2xx-adc.c | 25 ++++++++++++++++++++-----
 1 file changed, 20 insertions(+), 5 deletions(-)
drivers/iio/adc/ina2xx-adc.c +20 -5
index 857e1b69d6cd4..4e421f91f707f 100644
@@ -121,7 +121,7 @@ static const struct regmap_config ina2xx_regmap_config = {
 	.volatile_reg = ina2xx_is_volatile_reg,
 };
 
-enum ina2xx_ids { ina219, ina226 };
+enum ina2xx_ids { ina219, ina226, ina236 };
 
 struct ina2xx_config {
 	const char *name;
@@ -175,6 +175,16 @@ static const struct ina2xx_config ina2xx_config[] = {
 		.power_lsb_factor = 25,
 		.chip_id = ina226,
 	},
+	[ina236] = {
+		.name = "ina236",
+		.config_default = INA226_CONFIG_DEFAULT,
+		.calibration_value = 2048,
+		.shunt_voltage_lsb = 2500,
+		.bus_voltage_shift = 0,
+		.bus_voltage_lsb = 1600,
+		.power_lsb_factor = 32,
+		.chip_id = ina236,
+	},
 };
 
 static int ina2xx_read_raw(struct iio_dev *indio_dev,
@@ -499,7 +509,7 @@ static int ina2xx_write_raw(struct iio_dev *indio_dev,
 		break;
 
 	case IIO_CHAN_INFO_INT_TIME:
-		if (chip->config->chip_id == ina226) {
+		if (chip->config->chip_id != ina219) {
 			if (chan->address == INA2XX_SHUNT_VOLTAGE)
 				ret = ina226_set_int_time_vshunt(chip, val2,
 								 &tmp);
@@ -727,7 +737,7 @@ static int ina2xx_conversion_ready(struct iio_dev *indio_dev)
 	 * For now, we do an extra read of the MASK_ENABLE register (INA226)
 	 * resp. the BUS_VOLTAGE register (INA219).
 	 */
-	if (chip->config->chip_id == ina226) {
+	if (chip->config->chip_id != ina219) {
 		ret = regmap_read(chip->regmap,
 				  INA226_MASK_ENABLE, &alert);
 		alert &= INA226_CVRF;
@@ -998,7 +1008,7 @@ static int ina2xx_probe(struct i2c_client *client)
 	/* Patch the current config register with default. */
 	val = chip->config->config_default;
 
-	if (type == ina226) {
+	if (type != ina219) {
 		ina226_set_average(chip, INA226_DEFAULT_AVG, &val);
 		ina226_set_int_time_vbus(chip, INA226_DEFAULT_IT, &val);
 		ina226_set_int_time_vshunt(chip, INA226_DEFAULT_IT, &val);
@@ -1017,7 +1027,7 @@ static int ina2xx_probe(struct i2c_client *client)
 	}
 
 	indio_dev->modes = INDIO_DIRECT_MODE;
-	if (type == ina226) {
+	if (type != ina219) {
 		indio_dev->channels = ina226_channels;
 		indio_dev->num_channels = ARRAY_SIZE(ina226_channels);
 		indio_dev->info = &ina226_info;
@@ -1057,6 +1067,7 @@ static const struct i2c_device_id ina2xx_id[] = {
 	{ "ina226", ina226 },
 	{ "ina230", ina226 },
 	{ "ina231", ina226 },
+	{ "ina236", ina236 },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, ina2xx_id);
@@ -1082,6 +1093,10 @@ static const struct of_device_id ina2xx_of_match[] = {
 		.compatible = "ti,ina231",
 		.data = (void *)ina226
 	},
+	{
+		.compatible = "ti,ina236",
+		.data = (void *)ina236
+	},
 	{ }
 };
 MODULE_DEVICE_TABLE(of, ina2xx_of_match);
Signature · 1 line
2.51.2