phy: qcom: edp: Add DP/eDP switch for phys
Subsystems (3)
v4 cover phy: qcom: edp: Add DP/eDP switch for phys
Currently the PHY selects the DP/eDP configuration tables in a fixed way, choosing the table when enable. This driver has known issues:
1. The selected table does not match the actual platform mode.
2. It cannot support both modes at the same time.
As discussed here[1], this series:
1. Cleans up duplicated and incorrect tables based on the HPG.
2. Fixes the LDO programming error in eDP mode.
3. Adds DP/eDP mode switching support.
Note: x1e80100/sa8775p/sc7280/SC8280XP have been tested, while glymur/sc8180x have not been tested.
[1] https://lore.kernel.org/all/[email protected]/
---
Changes in v4:
- Splite changes.[Dmitry]
- Add sc8180x tables in a single chagne.[Dmitry][Konrad]
- Link to v3: https://lore.kernel.org/r/[email protected]
Changes in v3:
- Rebase to next-20260224.[Dmitry]
- Only enable TX1 LDO when lane counts > 2.[Konrad]
- Link to v2: https://lore.kernel.org/all/[email protected]/
Changes in v2:
- Combine the third patch with the first one.[Dmitry]
- Fix code formatting issues.[Konrad][Dmitry]
- Update the commit message description.[Dmitry][Konrad]
- Fix kodiak swing/pre_emp table values.[Konrad]
---
Yongxing Mou (5):
phy: qcom: edp: Unify generic DP/eDP swing and pre-emphasis tables
phy: qcom: edp: Add eDP/DP mode switch support
phy: qcom: edp: Add SC7280/SC8180X swing/pre-emphasis tables
phy: qcom: edp: Fix AUX_CFG8 programming for DP mode
phy: qcom: edp: Add PHY-specific LDO config for eDP low vdiff
drivers/phy/qualcomm/phy-qcom-edp.c | 221 ++++++++++++++++++++++++++++-------- 1 file changed, 173 insertions(+), 48 deletions(-)
---
base-commit: bee6ea30c48788e18348309f891ed8afbf7702ac
change-id: 20260205-edp_phy-1eca3ed074c0
Best regards,
Signature · 1 line
Yongxing Mou <[email protected]>
PATCH v4 1/5 phy: qcom: edp: Unify generic DP/eDP swing and pre-emphasis tables
The current eDP and DP swing/pre-emphasis tables do not match the HPG requirements for the supported platforms, correct the table accordingly.
The generic tables which can be shared as follows:
DP mode:
-sa8775p/sc7280/sc8280xp/x1e80100 -glymur -sc8180x eDP mode(low vdiff): -glymur/sa8775p/sc8280xp/x1e80100 -sc7280 -sc8180x
The proper tables for SC8180X and SC7280 will be added in a later patch, since they need separate table.
--- drivers/phy/qualcomm/phy-qcom-edp.c | 41 +++++++++---------------------------- 1 file changed, 10 insertions(+), 31 deletions(-)
drivers/phy/qualcomm/phy-qcom-edp.c +10 -31
@@ -116,17 +116,17 @@ struct qcom_edp { };static const u8 dp_swing_hbr_rbr[4 ][4 ] = { - {0x08 ,0x0f ,0x16 ,0x1f }, + {0x07 ,0x0f ,0x16 ,0x1f }, {0x11 ,0x1e ,0x1f ,0xff }, {0x16 ,0x1f ,0xff ,0xff }, {0x1f ,0xff ,0xff ,0xff } };static const u8 dp_pre_emp_hbr_rbr[4 ][4 ] = { - {0x00 ,0x0d ,0x14 ,0x1a }, + {0x00 ,0x0e ,0x15 ,0x1a }, {0x00 ,0x0e ,0x15 ,0xff }, {0x00 ,0x0e ,0xff ,0xff }, - {0x03 ,0xff ,0xff ,0xff } + {0x04 ,0xff ,0xff ,0xff } };static const u8 dp_swing_hbr2_hbr3[4 ][4 ] = {
@@ -158,7 +158,7 @@ static const u8 edp_swing_hbr_rbr[4][4] = { };static const u8 edp_pre_emp_hbr_rbr[4 ][4 ] = { - {0x05 ,0x12 ,0x17 ,0x1d }, + {0x05 ,0x11 ,0x17 ,0x1d }, {0x05 ,0x11 ,0x18 ,0xff }, {0x06 ,0x11 ,0xff ,0xff }, {0x00 ,0xff ,0xff ,0xff }
@@ -172,10 +172,10 @@ static const u8 edp_swing_hbr2_hbr3[4][4] = { };static const u8 edp_pre_emp_hbr2_hbr3[4 ][4 ] = { - {0x08 ,0x11 ,0x17 ,0x1b }, - {0x00 ,0x0c ,0x13 ,0xff }, - {0x05 ,0x10 ,0xff ,0xff }, - {0x00 ,0xff ,0xff ,0xff } + {0x0c ,0x15 ,0x19 ,0x1e }, + {0x0b ,0x15 ,0x19 ,0xff }, + {0x0e ,0x14 ,0xff ,0xff }, + {0x0d ,0xff ,0xff ,0xff } };static const struct qcom_edp_swing_pre_emph_cfg edp_phy_swing_pre_emph_cfg = {
@@ -193,27 +193,6 @@ static const u8 edp_phy_vco_div_cfg_v4[4] = { 0x01, 0x01, 0x02, 0x00, }; -static const u8 edp_pre_emp_hbr_rbr_v5[4 ][4 ] = { - {0x05 ,0x11 ,0x17 ,0x1d }, - {0x05 ,0x11 ,0x18 ,0xff }, - {0x06 ,0x11 ,0xff ,0xff }, - {0x00 ,0xff ,0xff ,0xff } -}; - -static const u8 edp_pre_emp_hbr2_hbr3_v5[4 ][4 ] = { - {0x0c ,0x15 ,0x19 ,0x1e }, - {0x0b ,0x15 ,0x19 ,0xff }, - {0x0e ,0x14 ,0xff ,0xff }, - {0x0d ,0xff ,0xff ,0xff } -}; - -static const struct qcom_edp_swing_pre_emph_cfg edp_phy_swing_pre_emph_cfg_v5 = { - .swing_hbr_rbr = &edp_swing_hbr_rbr, - .swing_hbr3_hbr2 = &edp_swing_hbr2_hbr3, - .pre_emphasis_hbr_rbr = &edp_pre_emp_hbr_rbr_v5, - .pre_emphasis_hbr3_hbr2 = &edp_pre_emp_hbr2_hbr3_v5, -}; -static const u8 edp_phy_aux_cfg_v5[DP_AUX_CFG_SIZE ] = {0x00 ,0x13 ,0xa4 ,0x00 ,0x0a ,0x26 ,0x0a ,0x03 ,0x37 ,0x03 ,0x02 ,0x02 ,0x00 , };
@@ -564,7 +543,7 @@ static const struct qcom_edp_phy_cfg sa8775p_dp_phy_cfg = { .is_edp = false, .aux_cfg = edp_phy_aux_cfg_v5, .vco_div_cfg = edp_phy_vco_div_cfg_v4, - .swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg_v5, + .swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg, .ver_ops = &qcom_edp_phy_ops_v4, };
@@ -945,7 +924,7 @@ static const struct phy_ver_ops qcom_edp_phy_ops_v8 = {static struct qcom_edp_phy_cfg glymur_phy_cfg = { .aux_cfg = edp_phy_aux_cfg_v8, .vco_div_cfg = edp_phy_vco_div_cfg_v8, - .swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg_v5, + .swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg, .ver_ops = &qcom_edp_phy_ops_v8, };
Signature · 1 line
2.43.0
Re: [PATCH v4 1/5] phy: qcom: edp: Unify generic DP/eDP swing and pre-emphasis tables
Quoted 17 lines · Yongxing Mou
The current eDP and DP swing/pre-emphasis tables do not match the HPG requirements for the supported platforms, correct the table accordingly.
The generic tables which can be shared as follows:
DP mode:
-sa8775p/sc7280/sc8280xp/x1e80100 -glymur -sc8180x eDP mode(low vdiff): -glymur/sa8775p/sc8280xp/x1e80100 -sc7280 -sc8180xThe proper tables for SC8180X and SC7280 will be added in a later patch, since they need separate table.
Quoted 8 lines
Fixes f199223cb490 ("phy: qcom: Introduce new eDP PHY driver")Reviewed-by Konrad Dybcio <[email protected]>Signed-off-by Yongxing Mou <[email protected]>--- drivers/phy/qualcomm/phy-qcom-edp.c | 41 +++++++++---------------------------- 1 file changed, 10 insertions(+), 31 deletions(-)
Signature · 2 lines
With best wishes Dmitry
PATCH v4 2/5 phy: qcom: edp: Add eDP/DP mode switch support
In reply to Yongxing MouThe eDP PHY supports both eDP/DP modes, each requires a different table. The current driver doesn't support both modes and use either the eDP or DP table when enable the platform. Add a separate set of tables for eDP and DP modes, and select the appropriate table based on the current mode.
Glymur's DP mode table differs from the other platforms, add a dedicated table for it.
Since both modes are supported, so also fixes the table mismatch for X1E80100(eDP) and SA8775P(DP).
--- drivers/phy/qualcomm/phy-qcom-edp.c | 46 +++++++++++++++++++++++++++---------- 1 file changed, 34 insertions(+), 12 deletions(-)
drivers/phy/qualcomm/phy-qcom-edp.c +34 -12
@@ -87,7 +87,8 @@ struct qcom_edp_phy_cfg {bool is_edp;const u8 *aux_cfg;const u8 *vco_div_cfg; -const struct qcom_edp_swing_pre_emph_cfg *swing_pre_emph_cfg; +const struct qcom_edp_swing_pre_emph_cfg *dp_swing_pre_emph_cfg; +const struct qcom_edp_swing_pre_emph_cfg *edp_swing_pre_emph_cfg;const struct phy_ver_ops *ver_ops; };
@@ -150,6 +151,20 @@ static const struct qcom_edp_swing_pre_emph_cfg dp_phy_swing_pre_emph_cfg = { .pre_emphasis_hbr3_hbr2 = &dp_pre_emp_hbr2_hbr3, }; +static const u8 dp_pre_emp_hbr_rbr_v8[4 ][4 ] = { + {0x00 ,0x0e ,0x15 ,0x1a }, + {0x00 ,0x0e ,0x15 ,0xff }, + {0x00 ,0x0e ,0xff ,0xff }, + {0x00 ,0xff ,0xff ,0xff } +}; + +static const struct qcom_edp_swing_pre_emph_cfg dp_phy_swing_pre_emph_cfg_v8 = { + .swing_hbr_rbr = &dp_swing_hbr_rbr, + .swing_hbr3_hbr2 = &dp_swing_hbr2_hbr3, + .pre_emphasis_hbr_rbr = &dp_pre_emp_hbr_rbr_v8, + .pre_emphasis_hbr3_hbr2 = &dp_pre_emp_hbr2_hbr3, +}; +static const u8 edp_swing_hbr_rbr[4 ][4 ] = { {0x07 ,0x0f ,0x16 ,0x1f }, {0x0d ,0x16 ,0x1e ,0xff },
@@ -246,7 +261,7 @@ static int qcom_edp_phy_init(struct phy *phy)* when more information becomes available about why this is * even needed. */ -if (edp->cfg->swing_pre_emph_cfg && !edp->is_edp) +if (edp->cfg->dp_swing_pre_emph_cfg && !edp->is_edp) aux_cfg[8 ] =0xb7 ;writel (0xfc , edp->edp +DP_PHY_MODE );
@@ -270,7 +285,7 @@ static int qcom_edp_phy_init(struct phy *phy)static int qcom_edp_set_voltages (struct qcom_edp *edp,const struct phy_configure_opts_dp *dp_opts) { -const struct qcom_edp_swing_pre_emph_cfg *cfg = edp->cfg->swing_pre_emph_cfg; +const struct qcom_edp_swing_pre_emph_cfg *cfg;unsigned int v_level =0 ;unsigned int p_level =0 ;u8 ldo_config;
@@ -278,12 +293,14 @@ static int qcom_edp_set_voltages(struct qcom_edp *edp, const struct phy_configuru8 emph;int i; +if (edp->is_edp) + cfg = edp->cfg->edp_swing_pre_emph_cfg; +else + cfg = edp->cfg->dp_swing_pre_emph_cfg; +if (!cfg)return 0 ; -if (edp->is_edp) - cfg = &edp_phy_swing_pre_emph_cfg; -for (i =0 ; i < dp_opts->lanes; i++) { v_level =max (v_level, dp_opts->voltage[i]); p_level =max (p_level, dp_opts->pre[i]);
@@ -543,7 +560,8 @@ static const struct qcom_edp_phy_cfg sa8775p_dp_phy_cfg = { .is_edp = false, .aux_cfg = edp_phy_aux_cfg_v5, .vco_div_cfg = edp_phy_vco_div_cfg_v4, - .swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg, + .dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg, + .edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg, .ver_ops = &qcom_edp_phy_ops_v4, };
@@ -556,7 +574,8 @@ static const struct qcom_edp_phy_cfg sc7280_dp_phy_cfg = {static const struct qcom_edp_phy_cfg sc8280xp_dp_phy_cfg = { .aux_cfg = edp_phy_aux_cfg_v4, .vco_div_cfg = edp_phy_vco_div_cfg_v4, - .swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg, + .dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg, + .edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg, .ver_ops = &qcom_edp_phy_ops_v4, };
@@ -564,7 +583,8 @@ static const struct qcom_edp_phy_cfg sc8280xp_edp_phy_cfg = { .is_edp = true, .aux_cfg = edp_phy_aux_cfg_v4, .vco_div_cfg = edp_phy_vco_div_cfg_v4, - .swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg, + .dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg, + .edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg, .ver_ops = &qcom_edp_phy_ops_v4, };
@@ -745,7 +765,8 @@ static const struct phy_ver_ops qcom_edp_phy_ops_v6 = {static struct qcom_edp_phy_cfg x1e80100_phy_cfg = { .aux_cfg = edp_phy_aux_cfg_v4, .vco_div_cfg = edp_phy_vco_div_cfg_v4, - .swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg, + .dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg, + .edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg, .ver_ops = &qcom_edp_phy_ops_v6, };
@@ -924,7 +945,8 @@ static const struct phy_ver_ops qcom_edp_phy_ops_v8 = {static struct qcom_edp_phy_cfg glymur_phy_cfg = { .aux_cfg = edp_phy_aux_cfg_v8, .vco_div_cfg = edp_phy_vco_div_cfg_v8, - .swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg, + .dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg_v8, + .edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg, .ver_ops = &qcom_edp_phy_ops_v8, };
@@ -942,7 +964,7 @@ static int qcom_edp_phy_power_on(struct phy *phy)if (ret)return ret; -if (edp->cfg->swing_pre_emph_cfg && !edp->is_edp) +if (edp->cfg->edp_swing_pre_emph_cfg && !edp->is_edp) ldo_config =0x1 ;writel (ldo_config, edp->tx0 + TXn_LDO_CONFIG);
Signature · 1 line
2.43.0
Re: [PATCH v4 2/5] phy: qcom: edp: Add eDP/DP mode switch support
Quoted 3 lines · Yongxing Mou
The eDP PHY supports both eDP/DP modes, each requires a different table. The current driver doesn't support both modes and use either the eDP or DP table when enable the platform.
This is not quite true. The driver supports both modes, but it uses a fixed static table for eDP programming.
Other than the commit message, LGTM.
Quoted 17 lines
Add a separate set of tables for eDP
and DP modes, and select the appropriate table based on the current mode.Glymur's DP mode table differs from the other platforms, add a dedicated table for it.
Since both modes are supported, so also fixes the table mismatch for X1E80100(eDP) and SA8775P(DP).
Fixes 3f12bf16213c ("phy: qcom: edp: Add support for eDP PHY on SA8775P")Reviewed-by Konrad Dybcio <[email protected]>Signed-off-by Yongxing Mou <[email protected]>--- drivers/phy/qualcomm/phy-qcom-edp.c | 46 +++++++++++++++++++++++++++---------- 1 file changed, 34 insertions(+), 12 deletions(-)
Signature · 2 lines
With best wishes Dmitry
Re: [PATCH v4 2/5] phy: qcom: edp: Add eDP/DP mode switch support
Quoted 10 lines · Dmitry Baryshkov
Quoted 3 lines · Yongxing Mou
The eDP PHY supports both eDP/DP modes, each requires a different table. The current driver doesn't support both modes and use either the eDP or DP table when enable the platform.
This is not quite true. The driver supports both modes, but it uses a fixed static table for eDP programming.
Other than the commit message, LGTM.
Will modify next patch.
Quoted 19 lines
Quoted 18 lines
Add a separate set of tables for eDP
and DP modes, and select the appropriate table based on the current mode.Glymur's DP mode table differs from the other platforms, add a dedicated table for it.
Since both modes are supported, so also fixes the table mismatch for X1E80100(eDP) and SA8775P(DP).
Fixes 3f12bf16213c ("phy: qcom: edp: Add support for eDP PHY on SA8775P")Reviewed-by Konrad Dybcio <[email protected]>Signed-off-by Yongxing Mou <[email protected]>--- drivers/phy/qualcomm/phy-qcom-edp.c | 46 +++++++++++++++++++++++++++---------- 1 file changed, 34 insertions(+), 12 deletions(-)
PATCH v4 3/5 phy: qcom: edp: Add SC7280/SC8180X swing/pre-emphasis tables
In reply to Yongxing MouSC7280 and SC8180X previously shared the same cfg because they did not use swing/pre-emphasis tables. Add the corresponding tables for these platforms. Since they have different PHY sub-versions, their eDP/DP mode tables also differ, so move SC8180X to its own cfg instead of reusing the SC7280 one.
--- drivers/phy/qualcomm/phy-qcom-edp.c | 71 ++++++++++++++++++++++++++++++++++--- 1 file changed, 67 insertions(+), 4 deletions(-)
drivers/phy/qualcomm/phy-qcom-edp.c +67 -4
@@ -165,6 +165,27 @@ static const struct qcom_edp_swing_pre_emph_cfg dp_phy_swing_pre_emph_cfg_v8 = { .pre_emphasis_hbr3_hbr2 = &dp_pre_emp_hbr2_hbr3, }; +static const u8 dp_swing_hbr2_hbr3_v2[4 ][4 ] = { + {0x27 ,0x2f ,0x36 ,0xff }, + {0x31 ,0x3e ,0x3f ,0xff }, + {0x3a ,0x3f ,0xff ,0xff }, + {0xff ,0xff ,0xff ,0xff } +}; + +static const u8 dp_pre_emp_hbr2_hbr3_v2[4 ][4 ] = { + {0x20 ,0x2e ,0x35 ,0xff }, + {0x20 ,0x2e ,0x35 ,0xff }, + {0x20 ,0x2e ,0xff ,0xff }, + {0xff ,0xff ,0xff ,0xff } +}; + +static const struct qcom_edp_swing_pre_emph_cfg dp_phy_swing_pre_emph_cfg_v2 = { + .swing_hbr_rbr = &dp_swing_hbr_rbr, + .swing_hbr3_hbr2 = &dp_swing_hbr2_hbr3_v2, + .pre_emphasis_hbr_rbr = &dp_pre_emp_hbr_rbr, + .pre_emphasis_hbr3_hbr2 = &dp_pre_emp_hbr2_hbr3_v2, +}; +static const u8 edp_swing_hbr_rbr[4 ][4 ] = { {0x07 ,0x0f ,0x16 ,0x1f }, {0x0d ,0x16 ,0x1e ,0xff },
@@ -208,6 +229,41 @@ static const u8 edp_phy_vco_div_cfg_v4[4] = { 0x01, 0x01, 0x02, 0x00, }; +static const u8 edp_pre_emp_hbr2_hbr3_v2[4 ][4 ] = { + {0x0c ,0x15 ,0x19 ,0x1e }, + {0x08 ,0x15 ,0x19 ,0xff }, + {0x0e ,0x14 ,0xff ,0xff }, + {0x0d ,0xff ,0xff ,0xff } +}; + +static const struct qcom_edp_swing_pre_emph_cfg edp_phy_swing_pre_emph_cfg_v2 = { + .swing_hbr_rbr = &edp_swing_hbr_rbr, + .swing_hbr3_hbr2 = &edp_swing_hbr2_hbr3, + .pre_emphasis_hbr_rbr = &edp_pre_emp_hbr_rbr, + .pre_emphasis_hbr3_hbr2 = &edp_pre_emp_hbr2_hbr3_v2, +}; + +static const u8 edp_swing_hbr2_hbr3_v3[4 ][4 ] = { + {0x06 ,0x11 ,0x16 ,0x1b }, + {0x0b ,0x19 ,0x1f ,0xff }, + {0x18 ,0x1f ,0xff ,0xff }, + {0x1f ,0xff ,0xff ,0xff } +}; + +static const u8 edp_pre_emp_hbr2_hbr3_v3[4 ][4 ] = { + {0x0c ,0x15 ,0x19 ,0x1e }, + {0x09 ,0x14 ,0x19 ,0xff }, + {0x0f ,0x14 ,0xff ,0xff }, + {0x0d ,0xff ,0xff ,0xff } +}; + +static const struct qcom_edp_swing_pre_emph_cfg edp_phy_swing_pre_emph_cfg_v3 = { + .swing_hbr_rbr = &edp_swing_hbr_rbr, + .swing_hbr3_hbr2 = &edp_swing_hbr2_hbr3_v3, + .pre_emphasis_hbr_rbr = &edp_pre_emp_hbr_rbr, + .pre_emphasis_hbr3_hbr2 = &edp_pre_emp_hbr2_hbr3_v3, +}; +static const u8 edp_phy_aux_cfg_v5[DP_AUX_CFG_SIZE ] = {0x00 ,0x13 ,0xa4 ,0x00 ,0x0a ,0x26 ,0x0a ,0x03 ,0x37 ,0x03 ,0x02 ,0x02 ,0x00 , };
@@ -298,9 +354,6 @@ static int qcom_edp_set_voltages(struct qcom_edp *edp, const struct phy_configurelse cfg = edp->cfg->dp_swing_pre_emph_cfg; -if (!cfg) -return 0 ; -for (i =0 ; i < dp_opts->lanes; i++) { v_level =max (v_level, dp_opts->voltage[i]); p_level =max (p_level, dp_opts->pre[i]);
@@ -568,6 +621,16 @@ static const struct qcom_edp_phy_cfg sa8775p_dp_phy_cfg = {static const struct qcom_edp_phy_cfg sc7280_dp_phy_cfg = { .aux_cfg = edp_phy_aux_cfg_v4, .vco_div_cfg = edp_phy_vco_div_cfg_v4, + .dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg, + .edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg_v3, + .ver_ops = &qcom_edp_phy_ops_v4, +}; + +static const struct qcom_edp_phy_cfg sc8180x_dp_phy_cfg = { + .aux_cfg = edp_phy_aux_cfg_v4, + .vco_div_cfg = edp_phy_vco_div_cfg_v4, + .dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg_v2, + .edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg_v2, .ver_ops = &qcom_edp_phy_ops_v4, };
@@ -1348,7 +1411,7 @@ static const struct of_device_id qcom_edp_phy_match_table[] = { { .compatible = "qcom,glymur-dp-phy", .data = &glymur_phy_cfg, }, { .compatible = "qcom,sa8775p-edp-phy", .data = &sa8775p_dp_phy_cfg, }, { .compatible = "qcom,sc7280-edp-phy", .data = &sc7280_dp_phy_cfg, }, - { .compatible = "qcom,sc8180x-edp-phy", .data = &sc7280_dp_phy_cfg, }, + { .compatible = "qcom,sc8180x-edp-phy", .data = &sc8180x_dp_phy_cfg, }, { .compatible = "qcom,sc8280xp-dp-phy", .data = &sc8280xp_dp_phy_cfg, }, { .compatible = "qcom,sc8280xp-edp-phy", .data = &sc8280xp_edp_phy_cfg, }, { .compatible = "qcom,x1e80100-dp-phy", .data = &x1e80100_phy_cfg, },
Signature · 1 line
2.43.0
Re: [PATCH v4 3/5] phy: qcom: edp: Add SC7280/SC8180X swing/pre-emphasis tables
Review
Quoted 13 lines · Yongxing Mou
SC7280 and SC8180X previously shared the same cfg because they did not use swing/pre-emphasis tables. Add the corresponding tables for these platforms. Since they have different PHY sub-versions, their eDP/DP mode tables also differ, so move SC8180X to its own cfg instead of reusing the SC7280 one.
Signed-off-by Yongxing Mou <[email protected]>---
(quoted diff) +2
-0+static const struct qcom_edp_swing_pre_emph_cfg edp_phy_swing_pre_emph_cfg_v2 = { + .swing_hbr_rbr = &edp_swing_hbr_rbr,
For eDP / low-Vdiff:
I believe the RBR swing settings for 8180 should
instead be:
0x07 0x0f 0x17 0x1f (matches)
(the rest differs)0x0d 0x16 0x1e0x11 0x1b0x16
The preem RBR almost matches, one byte is off
(arr[0][1] = 0x12 on poipu, 0x11 on kodiak)
The swing and preem settings for HBR3 look OK
For DP / low-Vdiff:
.swing_hbr3_hbr2 OK
.swing_hbr_rbr - I don't know. The docs are unclear whether the same settings should be used for RBR and HBR3, but maybe? There's a separate table for mini-DP but I doubt there's any poipu boards with such a connector (maybe some obscure ones)
.pre_emphasis_hbr3_hbr2 OK
.pre_emphasis_hbr_rbr same as above
Konrad
Re: [PATCH v4 3/5] phy: qcom: edp: Add SC7280/SC8180X swing/pre-emphasis tables
Quoted 17 lines · Konrad Dybcio
Review
Quoted 13 lines · Yongxing Mou
SC7280 and SC8180X previously shared the same cfg because they did not use swing/pre-emphasis tables. Add the corresponding tables for these platforms. Since they have different PHY sub-versions, their eDP/DP mode tables also differ, so move SC8180X to its own cfg instead of reusing the SC7280 one.
Signed-off-by Yongxing Mou <[email protected]>---
(quoted diff) +2
-0+static const struct qcom_edp_swing_pre_emph_cfg edp_phy_swing_pre_emph_cfg_v2 = { + .swing_hbr_rbr = &edp_swing_hbr_rbr,For eDP / low-Vdiff:
Quoted 4 lines
I believe the RBR swing settings for 8180 should
instead be:
0x070x0f0x170x1f(matches)
0x07, 0x0f, 0x16, 0x1f
Quoted 10 lines
(the rest differs)
0x0d0x160x1e0x110x1b0x16The preem RBR almost matches, one byte is off
(arr[0][1] =0x12on poipu,0x11on kodiak)The swing and preem settings for HBR3 look OK
Signature · 2 lines
With best wishes Dmitry
Re: [PATCH v4 3/5] phy: qcom: edp: Add SC7280/SC8180X swing/pre-emphasis tables
Quoted 18 lines · Dmitry Baryshkov
Quoted 17 lines · Konrad Dybcio
Review
Quoted 13 lines · Yongxing Mou
SC7280 and SC8180X previously shared the same cfg because they did not use swing/pre-emphasis tables. Add the corresponding tables for these platforms. Since they have different PHY sub-versions, their eDP/DP mode tables also differ, so move SC8180X to its own cfg instead of reusing the SC7280 one.
Signed-off-by Yongxing Mou <[email protected]>---
(quoted diff) +2
-0+static const struct qcom_edp_swing_pre_emph_cfg edp_phy_swing_pre_emph_cfg_v2 = { + .swing_hbr_rbr = &edp_swing_hbr_rbr,For eDP / low-Vdiff:
Quoted 6 lines
Quoted 4 lines
I believe the RBR swing settings for 8180 should
instead be:
0x070x0f0x170x1f(matches)
0x07,0x0f,0x16,0x1f
Yes, you're right
Konrad
Re: [PATCH v4 3/5] phy: qcom: edp: Add SC7280/SC8180X swing/pre-emphasis tables
In reply to Konrad DybcioQuoted 17 lines · Konrad Dybcio
Review
Quoted 13 lines · Yongxing Mou
SC7280 and SC8180X previously shared the same cfg because they did not use swing/pre-emphasis tables. Add the corresponding tables for these platforms. Since they have different PHY sub-versions, their eDP/DP mode tables also differ, so move SC8180X to its own cfg instead of reusing the SC7280 one.
Signed-off-by Yongxing Mou <[email protected]>---
(quoted diff) +2
-0+static const struct qcom_edp_swing_pre_emph_cfg edp_phy_swing_pre_emph_cfg_v2 = { + .swing_hbr_rbr = &edp_swing_hbr_rbr,For eDP / low-Vdiff:
Quoted 4 lines
I believe the RBR swing settings for 8180 should
instead be:
0x070x0f0x170x1f(matches)
Emm i see from ipcat eDP Low vdiff(Lower HBR) swing settings is 0x07 0x0f 0x16 0x1f
Quoted 10 lines
(the rest differs)
0x0d0x160x1e0x110x1b0x16The preem RBR almost matches, one byte is off
(arr[0][1] =0x12on poipu,0x11on kodiak)
Thanks,, here need to be fixed.
Quoted 4 lines
The swing and preem settings for HBR3 look OK
For DP / low-Vdiff:
Quoted 9 lines
.swing_hbr3_hbr2 OK
.swing_hbr_rbr - I don't know. The docs are unclear whether the same settings should be used for RBR and HBR3, but maybe? There's a separate table for mini-DP but I doubt there's any poipu boards with such a connector (maybe some obscure ones).pre_emphasis_hbr3_hbr2 OK
.pre_emphasis_hbr_rbr same as above
Thanks for point this, so pre_emphasis_hbr_rbr same with pre_emphasis_hbr3_hbr2? I also don't get it's RBR or HBR3 from phy HPG. But now i think only eDP will be used in upstreamed poipu boards. i check the dts and not find any poipu boards will use DP mode(or mini DP)..
Quoted 1 line
Konrad
Re: [PATCH v4 3/5] phy: qcom: edp: Add SC7280/SC8180X swing/pre-emphasis tables
Quoted 13 lines · Yongxing Mou
Quoted 10 lines · Konrad Dybcio
The swing and preem settings for HBR3 look OK
For DP / low-Vdiff:
.swing_hbr3_hbr2 OK
.swing_hbr_rbr - I don't know. The docs are unclear whether the same settings should be used for RBR and HBR3, but maybe? There's a separate table for mini-DP but I doubt there's any poipu boards with such a connector (maybe some obscure ones)
Quoted 7 lines
Quoted 3 lines
.pre_emphasis_hbr3_hbr2 OK
.pre_emphasis_hbr_rbr same as aboveThanks for point this, so
pre_emphasis_hbr_rbrsame withpre_emphasis_hbr3_hbr2? I also don't get it's RBR or HBR3 from phy HPG. But now i think only eDP will be used in upstreamed poipu boards. i check the dts and not find any poipu boards will use DP mode(or mini DP)..
After checking the HPG, could you please actually talk to the colleagues who brough up the PHY on those platforms (with the downstreaam kernels)? They might know the details not captured in the HPG.
Signature · 2 lines
With best wishes Dmitry
Re: [PATCH v4 3/5] phy: qcom: edp: Add SC7280/SC8180X swing/pre-emphasis tables
Quoted 17 lines · Dmitry Baryshkov
Quoted 16 lines · Yongxing Mou
Quoted 13 lines · Konrad Dybcio
The swing and preem settings for HBR3 look OK
For DP / low-Vdiff:
.swing_hbr3_hbr2 OK
.swing_hbr_rbr - I don't know. The docs are unclear whether the same settings should be used for RBR and HBR3, but maybe? There's a separate table for mini-DP but I doubt there's any poipu boards with such a connector (maybe some obscure ones).pre_emphasis_hbr3_hbr2 OK
.pre_emphasis_hbr_rbr same as above
Quoted 9 lines
Quoted 4 lines
Thanks for point this, so
pre_emphasis_hbr_rbrsame withpre_emphasis_hbr3_hbr2? I also don't get it's RBR or HBR3 from phy HPG. But now i think only eDP will be used in upstreamed poipu boards. i check the dts and not find any poipu boards will use DP mode(or mini DP)..After checking the HPG, could you please actually talk to the colleagues who brough up the PHY on those platforms (with the downstreaam kernels)? They might know the details not captured in the HPG.
The driver actually existed in the very first upstream version, but it didn’t use any tables back then.
On the downstream side, I couldn’t find any 7nm eDP PHY implementations either.
I tried reaching out to a few teams, but this platform is quite old and most people don’t really have context any more. My understanding is that it was primarily a compute-oriented chip, but I’m not very familiar with that code path myself. At this point, the only remaining option is to try contacting the hardware team to see if they have any additional insights. Since this is unlikely to be resolved quickly, I’d like to proceed with posting the next revision first. For SC8180X, it should only ever be using eDP mode.
Re: [PATCH v4 3/5] phy: qcom: edp: Add SC7280/SC8180X swing/pre-emphasis tables
In reply to Yongxing MouQuoted 18 lines · Yongxing Mou
Quoted 15 lines · Konrad Dybcio
Quoted 13 lines · Yongxing Mou
SC7280 and SC8180X previously shared the same cfg because they did not use swing/pre-emphasis tables. Add the corresponding tables for these platforms. Since they have different PHY sub-versions, their eDP/DP mode tables also differ, so move SC8180X to its own cfg instead of reusing the SC7280 one.
Signed-off-by Yongxing Mou <[email protected]>---
+static const struct
qcom_edp_swing_pre_emph_cfgedp_phy_swing_pre_emph_cfg_v2= { + .swing_hbr_rbr =&edp_swing_hbr_rbr,
Quoted 8 lines
Quoted 6 lines
For eDP / low-Vdiff:
I believe the RBR swing settings for 8180 should
instead be:
0x070x0f0x170x1f(matches)Emm i see from ipcat eDP Low vdiff(Lower HBR) swing settings is
0x070x0f0x160x1f
Yes, you're right, I made a typo
[...]
Quoted 4 lines
Quoted 3 lines
.pre_emphasis_hbr3_hbr2 OK
.pre_emphasis_hbr_rbr same as aboveThanks for point this, so
pre_emphasis_hbr_rbrsame with pre_emphasis_hbr3_hbr2? I also don't get it's RBR or HBR3 from phy HPG. But now i think only eDP will be used in upstreamed poipu boards. i check the dts and not find any poipu boards will use DP mode(or mini DP)..
Yeah let's not worry about it today..
Konrad
Re: [PATCH v4 3/5] phy: qcom: edp: Add SC7280/SC8180X swing/pre-emphasis tables
Quoted 30 lines · Konrad Dybcio
Quoted 18 lines · Yongxing Mou
Quoted 15 lines · Konrad Dybcio
Quoted 13 lines · Yongxing Mou
SC7280 and SC8180X previously shared the same cfg because they did not use swing/pre-emphasis tables. Add the corresponding tables for these platforms. Since they have different PHY sub-versions, their eDP/DP mode tables also differ, so move SC8180X to its own cfg instead of reusing the SC7280 one.
Signed-off-by Yongxing Mou <[email protected]>---
+static const struct
qcom_edp_swing_pre_emph_cfgedp_phy_swing_pre_emph_cfg_v2= { + .swing_hbr_rbr =&edp_swing_hbr_rbr,Quoted 8 lines
Quoted 6 lines
For eDP / low-Vdiff:
I believe the RBR swing settings for 8180 should
instead be:
0x070x0f0x170x1f(matches)Emm i see from ipcat eDP Low vdiff(Lower HBR) swing settings is
0x070x0f0x160x1fYes, you're right, I made a typo
Quoted 8 lines
[...]
Quoted 4 lines
Quoted 3 lines
.pre_emphasis_hbr3_hbr2 OK
.pre_emphasis_hbr_rbr same as aboveThanks for point this, so
pre_emphasis_hbr_rbrsame with pre_emphasis_hbr3_hbr2? I also don't get it's RBR or HBR3 from phy HPG. But now i think only eDP will be used in upstreamed poipu boards. i check the dts and not find any poipu boards will use DP mode(or mini DP)..Yeah let's not worry about it today..
About mini-dp specifically that is
Konrad
PATCH v4 4/5 phy: qcom: edp: Fix AUX_CFG8 programming for DP mode
In reply to Yongxing MouAUX_CFG8 depends on whether the PHY is operating in eDP or DP mode, not the selected swing/pre-emphasis table. All supported platforms already have the proper tables, so remove the unnecessary check.
--- drivers/phy/qualcomm/phy-qcom-edp.c | 7 +------ 1 file changed, 1 insertion(+), 6 deletions(-)
drivers/phy/qualcomm/phy-qcom-edp.c +1 -6
@@ -312,12 +312,7 @@ static int qcom_edp_phy_init(struct phy *phy)DP_PHY_PD_CTL_PLL_PWRDN |DP_PHY_PD_CTL_DP_CLAMP_EN , edp->edp + DP_PHY_PD_CTL); -/* -* TODO: Re-work the conditions around setting the cfg8 value -* when more information becomes available about why this is -* even needed. -*/ -if (edp->cfg->dp_swing_pre_emph_cfg && !edp->is_edp) +if (!edp->is_edp) aux_cfg[8 ] =0xb7 ;writel (0xfc , edp->edp +DP_PHY_MODE );
Signature · 1 line
2.43.0
Re: [PATCH v4 4/5] phy: qcom: edp: Fix AUX_CFG8 programming for DP mode
Quoted 10 lines · Yongxing Mou
AUX_CFG8depends on whether the PHY is operating in eDP or DP mode, not the selected swing/pre-emphasis table. All supported platforms already have the proper tables, so remove the unnecessary check.Reviewed-by Konrad Dybcio <[email protected]>Signed-off-by Yongxing Mou <[email protected]>--- drivers/phy/qualcomm/phy-qcom-edp.c | 7 +------ 1 file changed, 1 insertion(+), 6 deletions(-)
Fixes?
With the tag in place,
Signature · 2 lines
With best wishes Dmitry
PATCH v4 5/5 phy: qcom: edp: Add PHY-specific LDO config for eDP low vdiff
In reply to Yongxing MouFor eDP low vdiff, the LDO setting depends on the PHY version rather than being a simple 0x0 or 0x1 value. Introduce a PHY callback to program the correct LDO setting according to the HPG.
Since SC7280/SC8180X uses different LDO settings from SA8775P/SC8280XP, introduce qcom_edp_phy_ops_v3 to keep the LDO setting correct.
--- drivers/phy/qualcomm/phy-qcom-edp.c | 88 ++++++++++++++++++++++++++++++++----- 1 file changed, 77 insertions(+), 11 deletions(-)
drivers/phy/qualcomm/phy-qcom-edp.c +77 -11
@@ -81,6 +81,7 @@ struct phy_ver_ops {int (*com_clk_fwd_cfg)(const struct qcom_edp *edp);int (*com_configure_pll)(const struct qcom_edp *edp);int (*com_configure_ssc)(const struct qcom_edp *edp); +int (*com_ldo_config)(const struct qcom_edp *edp); };struct qcom_edp_phy_cfg {
@@ -339,7 +340,7 @@ static int qcom_edp_set_voltages(struct qcom_edp *edp, const struct phy_configurconst struct qcom_edp_swing_pre_emph_cfg *cfg;unsigned int v_level =0 ;unsigned int p_level =0 ; -u8 ldo_config; +int ret;u8 swing;u8 emph;int i;
@@ -365,13 +366,13 @@ static int qcom_edp_set_voltages(struct qcom_edp *edp, const struct phy_configurif (swing ==0xff || emph ==0xff )return -EINVAL ; - ldo_config = edp->is_edp ?0x0 :0x1 ; + ret = edp->cfg->ver_ops->com_ldo_config (edp); +if (ret) +return ret; -writel (ldo_config, edp->tx0 + TXn_LDO_CONFIG);writel (swing, edp->tx0 + TXn_TX_DRV_LVL);writel (emph, edp->tx0 + TXn_TX_EMP_POST1_LVL); -writel (ldo_config, edp->tx1 + TXn_LDO_CONFIG);writel (swing, edp->tx1 + TXn_TX_DRV_LVL);writel (emph, edp->tx1 + TXn_TX_EMP_POST1_LVL);
@@ -595,6 +596,52 @@ static int qcom_edp_com_configure_pll_v4(const struct qcom_edp *edp)return 0 ; } +static int qcom_edp_ldo_config_v3 (const struct qcom_edp *edp) +{ +const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts; +u32 ldo_config; + +if (!edp->is_edp) + ldo_config =0x0 ; +else if (dp_opts->link_rate <=2700 ) + ldo_config =0x81 ; +else + ldo_config =0x41 ; + +writel (ldo_config, edp->tx0 + TXn_LDO_CONFIG); +writel (dp_opts->lanes >2 ? ldo_config :0x00 , edp->tx1 + TXn_LDO_CONFIG); + +return 0 ; +} + +static int qcom_edp_ldo_config_v4 (const struct qcom_edp *edp) +{ +const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts; +u32 ldo_config; + +if (!edp->is_edp) + ldo_config =0x0 ; +else if (dp_opts->link_rate <=2700 ) + ldo_config =0xc1 ; +else + ldo_config =0x81 ; + +writel (ldo_config, edp->tx0 + TXn_LDO_CONFIG); +writel (dp_opts->lanes >2 ? ldo_config :0x00 , edp->tx1 + TXn_LDO_CONFIG); + +return 0 ; +} + +static const struct phy_ver_ops qcom_edp_phy_ops_v3 = { + .com_power_on = qcom_edp_phy_power_on_v4, + .com_resetsm_cntrl = qcom_edp_phy_com_resetsm_cntrl_v4, + .com_bias_en_clkbuflr = qcom_edp_com_bias_en_clkbuflr_v4, + .com_clk_fwd_cfg = qcom_edp_com_clk_fwd_cfg_v4, + .com_configure_pll = qcom_edp_com_configure_pll_v4, + .com_configure_ssc = qcom_edp_com_configure_ssc_v4, + .com_ldo_config = qcom_edp_ldo_config_v3, +}; +static const struct phy_ver_ops qcom_edp_phy_ops_v4 = { .com_power_on = qcom_edp_phy_power_on_v4, .com_resetsm_cntrl = qcom_edp_phy_com_resetsm_cntrl_v4,
@@ -602,6 +649,7 @@ static const struct phy_ver_ops qcom_edp_phy_ops_v4 = { .com_clk_fwd_cfg = qcom_edp_com_clk_fwd_cfg_v4, .com_configure_pll = qcom_edp_com_configure_pll_v4, .com_configure_ssc = qcom_edp_com_configure_ssc_v4, + .com_ldo_config = qcom_edp_ldo_config_v4, };static const struct qcom_edp_phy_cfg sa8775p_dp_phy_cfg = {
@@ -618,7 +666,7 @@ static const struct qcom_edp_phy_cfg sc7280_dp_phy_cfg = { .vco_div_cfg = edp_phy_vco_div_cfg_v4, .dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg, .edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg_v3, - .ver_ops = &qcom_edp_phy_ops_v4, + .ver_ops = &qcom_edp_phy_ops_v3, };static const struct qcom_edp_phy_cfg sc8180x_dp_phy_cfg = {
@@ -626,7 +674,7 @@ static const struct qcom_edp_phy_cfg sc8180x_dp_phy_cfg = { .vco_div_cfg = edp_phy_vco_div_cfg_v4, .dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg_v2, .edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg_v2, - .ver_ops = &qcom_edp_phy_ops_v4, + .ver_ops = &qcom_edp_phy_ops_v3, };static const struct qcom_edp_phy_cfg sc8280xp_dp_phy_cfg = {
@@ -811,6 +859,24 @@ static int qcom_edp_com_configure_pll_v6(const struct qcom_edp *edp)return 0 ; } +static int qcom_edp_ldo_config_v6 (const struct qcom_edp *edp) +{ +const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts; +u32 ldo_config; + +if (!edp->is_edp) + ldo_config =0x0 ; +else if (dp_opts->link_rate <=2700 ) + ldo_config =0x51 ; +else + ldo_config =0x91 ; + +writel (ldo_config, edp->tx0 + TXn_LDO_CONFIG); +writel (dp_opts->lanes >2 ? ldo_config :0x00 , edp->tx1 + TXn_LDO_CONFIG); + +return 0 ; +} +static const struct phy_ver_ops qcom_edp_phy_ops_v6 = { .com_power_on = qcom_edp_phy_power_on_v6, .com_resetsm_cntrl = qcom_edp_phy_com_resetsm_cntrl_v6,
@@ -818,6 +884,7 @@ static const struct phy_ver_ops qcom_edp_phy_ops_v6 = { .com_clk_fwd_cfg = qcom_edp_com_clk_fwd_cfg_v4, .com_configure_pll = qcom_edp_com_configure_pll_v6, .com_configure_ssc = qcom_edp_com_configure_ssc_v6, + .com_ldo_config = qcom_edp_ldo_config_v6, };static struct qcom_edp_phy_cfg x1e80100_phy_cfg = {
@@ -998,6 +1065,7 @@ static const struct phy_ver_ops qcom_edp_phy_ops_v8 = { .com_clk_fwd_cfg = qcom_edp_com_clk_fwd_cfg_v8, .com_configure_pll = qcom_edp_com_configure_pll_v8, .com_configure_ssc = qcom_edp_com_configure_ssc_v8, + .com_ldo_config = qcom_edp_ldo_config_v6, };static struct qcom_edp_phy_cfg glymur_phy_cfg = {
@@ -1013,7 +1081,6 @@ static int qcom_edp_phy_power_on(struct phy *phy)const struct qcom_edp *edp =phy_get_drvdata (phy);u32 bias0_en, drvr0_en, bias1_en, drvr1_en;unsigned long pixel_freq; -u8 ldo_config =0x0 ;int ret;u32 val;u8 cfg1;
@@ -1022,11 +1089,10 @@ static int qcom_edp_phy_power_on(struct phy *phy)if (ret)return ret; -if (edp->cfg->edp_swing_pre_emph_cfg && !edp->is_edp) - ldo_config =0x1 ; + ret = edp->cfg->ver_ops->com_ldo_config (edp); +if (ret) +return ret; -writel (ldo_config, edp->tx0 + TXn_LDO_CONFIG); -writel (ldo_config, edp->tx1 + TXn_LDO_CONFIG);writel (0x00 , edp->tx0 + TXn_LANE_MODE_1);writel (0x00 , edp->tx1 + TXn_LANE_MODE_1);
Signature · 1 line
2.43.0
Quoted 11 lines · Yongxing Mou
Currently the PHY selects the DP/eDP configuration tables in a fixed way, choosing the table when enable. This driver has known issues:
1. The selected table does not match the actual platform mode.
2. It cannot support both modes at the same time.As discussed here[1], this series:
1. Cleans up duplicated and incorrect tables based on the HPG.
2. Fixes the LDO programming error in eDP mode.
3. Adds DP/eDP mode switching support.Note: x1e80100/sa8775p/sc7280/SC8280XP have been tested, while
Tested with eDP or with mini-DP too?
Quoted 45 lines
glymur/sc8180x have not been tested.
[1] https://lore.kernel.org/all/[email protected]/
Signed-off-by Yongxing Mou <[email protected]>---
Changes in v4:
- Splite changes.[Dmitry]
- Add sc8180x tables in a single chagne.[Dmitry][Konrad]
- Link to v3: https://lore.kernel.org/r/[email protected]Changes in v3:
- Rebase to next-20260224.[Dmitry]
- Only enable TX1 LDO when lane counts > 2.[Konrad]
- Link to v2: https://lore.kernel.org/all/[email protected]/Changes in v2:
- Combine the third patch with the first one.[Dmitry]
- Fix code formatting issues.[Konrad][Dmitry]
- Update the commit message description.[Dmitry][Konrad]
- Fix kodiak swing/pre_emp table values.[Konrad]---
Yongxing Mou (5):
phy: qcom: edp: Unify generic DP/eDP swing and pre-emphasis tables
phy: qcom: edp: Add eDP/DP mode switch support
phy: qcom: edp: Add SC7280/SC8180X swing/pre-emphasis tables
phy: qcom: edp: FixAUX_CFG8programming for DP mode
phy: qcom: edp: Add PHY-specific LDO config for eDP low vdiffdrivers/phy/qualcomm/phy-qcom-edp.c | 221 ++++++++++++++++++++++++++++-------- 1 file changed, 173 insertions(+), 48 deletions(-)---
base-commit:bee6ea30c48788e18348309f891ed8afbf7702ac
change-id: 20260205-edp_phy-1eca3ed074c0Best regards,
Signature · 7 lines
Yongxing Mou <[email protected]> -- linux-phy mailing list [email protected] https://lists.infradead.org/mailman/listinfo/linux-phy
Signature · 2 lines
With best wishes Dmitry
Quoted 6 lines · Dmitry Baryshkov
Quoted 5 lines · Yongxing Mou
Currently the PHY selects the DP/eDP configuration tables in a fixed way, choosing the table when enable. This driver has known issues:
1. The selected table does not match the actual platform mode.
2. It cannot support both modes at the same time.
Quoted 9 lines
Quoted 6 lines
As discussed here[1], this series:
1. Cleans up duplicated and incorrect tables based on the HPG.
2. Fixes the LDO programming error in eDP mode.
3. Adds DP/eDP mode switching support.Note: x1e80100/sa8775p/sc7280/SC8280XP have been tested, while
Tested with eDP or with mini-DP too?
x1e80100 eDP (hamoa-evk)
sa8775p DP(full-size)
sc7280 (rb3, mini-DP)
sorry for sa8775p mini-DP... i don't have the hardware to test.
Quoted 46 lines
Quoted 45 lines
glymur/sc8180x have not been tested.
[1] https://lore.kernel.org/all/[email protected]/
Signed-off-by Yongxing Mou <[email protected]>---
Changes in v4:
- Splite changes.[Dmitry]
- Add sc8180x tables in a single chagne.[Dmitry][Konrad]
- Link to v3: https://lore.kernel.org/r/[email protected]Changes in v3:
- Rebase to next-20260224.[Dmitry]
- Only enable TX1 LDO when lane counts > 2.[Konrad]
- Link to v2: https://lore.kernel.org/all/[email protected]/Changes in v2:
- Combine the third patch with the first one.[Dmitry]
- Fix code formatting issues.[Konrad][Dmitry]
- Update the commit message description.[Dmitry][Konrad]
- Fix kodiak swing/pre_emp table values.[Konrad]---
Yongxing Mou (5):
phy: qcom: edp: Unify generic DP/eDP swing and pre-emphasis tables
phy: qcom: edp: Add eDP/DP mode switch support
phy: qcom: edp: Add SC7280/SC8180X swing/pre-emphasis tables
phy: qcom: edp: FixAUX_CFG8programming for DP mode
phy: qcom: edp: Add PHY-specific LDO config for eDP low vdiffdrivers/phy/qualcomm/phy-qcom-edp.c | 221 ++++++++++++++++++++++++++++-------- 1 file changed, 173 insertions(+), 48 deletions(-)---
base-commit:bee6ea30c48788e18348309f891ed8afbf7702ac
change-id: 20260205-edp_phy-1eca3ed074c0Best regards,
Signature · 7 lines
Yongxing Mou <[email protected]> -- linux-phy mailing list [email protected] https://lists.infradead.org/mailman/listinfo/linux-phy